/*
 * PMC-Sierra SPC 8001 SAS/SATA based host adapters driver
 *
 * Copyright (c) 2008-2009 USI Co., Ltd.
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions, and the following disclaimer,
 *    without modification.
 * 2. Redistributions in binary form must reproduce at minimum a disclaimer
 *    substantially similar to the "NO WARRANTY" disclaimer below
 *    ("Disclaimer") and any redistribution must be conditioned upon
 *    including a substantially similar Disclaimer requirement for further
 *    binary redistribution.
 * 3. Neither the names of the above-listed copyright holders nor the names
 *    of any contributors may be used to endorse or promote products derived
 *    from this software without specific prior written permission.
 *
 * Alternatively, this software may be distributed under the terms of the
 * GNU General Public License ("GPL") version 2 as published by the Free
 * Software Foundation.
 *
 * NO WARRANTY
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR
 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
 * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
 * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGES.
 *
 */
 #include <linux/slab.h>
 #include "pm8001_sas.h"
 #include "pm8001_hwi.h"
 #include "pm8001_chips.h"
 #include "pm8001_ctl.h"

/**
 * read_main_config_table - read the configure table and save it.
 * @pm8001_ha: our hba card information
 */
static void read_main_config_table(struct pm8001_hba_info *pm8001_ha)
{
        void __iomem *address = pm8001_ha->main_cfg_tbl_addr;
        pm8001_ha->main_cfg_tbl.pm8001_tbl.signature    =
                                pm8001_mr32(address, 0x00);
        pm8001_ha->main_cfg_tbl.pm8001_tbl.interface_rev =
                                pm8001_mr32(address, 0x04);
        pm8001_ha->main_cfg_tbl.pm8001_tbl.firmware_rev =
                                pm8001_mr32(address, 0x08);
        pm8001_ha->main_cfg_tbl.pm8001_tbl.max_out_io   =
                                pm8001_mr32(address, 0x0C);
        pm8001_ha->main_cfg_tbl.pm8001_tbl.max_sgl      =
                                pm8001_mr32(address, 0x10);
        pm8001_ha->main_cfg_tbl.pm8001_tbl.ctrl_cap_flag =
                                pm8001_mr32(address, 0x14);
        pm8001_ha->main_cfg_tbl.pm8001_tbl.gst_offset   =
                                pm8001_mr32(address, 0x18);
        pm8001_ha->main_cfg_tbl.pm8001_tbl.inbound_queue_offset =
                pm8001_mr32(address, MAIN_IBQ_OFFSET);
        pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_queue_offset =
                pm8001_mr32(address, MAIN_OBQ_OFFSET);
        pm8001_ha->main_cfg_tbl.pm8001_tbl.hda_mode_flag        =
                pm8001_mr32(address, MAIN_HDA_FLAGS_OFFSET);

        /* read analog Setting offset from the configuration table */
        pm8001_ha->main_cfg_tbl.pm8001_tbl.anolog_setup_table_offset =
                pm8001_mr32(address, MAIN_ANALOG_SETUP_OFFSET);

        /* read Error Dump Offset and Length */
        pm8001_ha->main_cfg_tbl.pm8001_tbl.fatal_err_dump_offset0 =
                pm8001_mr32(address, MAIN_FATAL_ERROR_RDUMP0_OFFSET);
        pm8001_ha->main_cfg_tbl.pm8001_tbl.fatal_err_dump_length0 =
                pm8001_mr32(address, MAIN_FATAL_ERROR_RDUMP0_LENGTH);
        pm8001_ha->main_cfg_tbl.pm8001_tbl.fatal_err_dump_offset1 =
                pm8001_mr32(address, MAIN_FATAL_ERROR_RDUMP1_OFFSET);
        pm8001_ha->main_cfg_tbl.pm8001_tbl.fatal_err_dump_length1 =
                pm8001_mr32(address, MAIN_FATAL_ERROR_RDUMP1_LENGTH);
}

/**
 * read_general_status_table - read the general status table and save it.
 * @pm8001_ha: our hba card information
 */
static void read_general_status_table(struct pm8001_hba_info *pm8001_ha)
{
        void __iomem *address = pm8001_ha->general_stat_tbl_addr;
        pm8001_ha->gs_tbl.pm8001_tbl.gst_len_mpistate   =
                                pm8001_mr32(address, 0x00);
        pm8001_ha->gs_tbl.pm8001_tbl.iq_freeze_state0   =
                                pm8001_mr32(address, 0x04);
        pm8001_ha->gs_tbl.pm8001_tbl.iq_freeze_state1   =
                                pm8001_mr32(address, 0x08);
        pm8001_ha->gs_tbl.pm8001_tbl.msgu_tcnt          =
                                pm8001_mr32(address, 0x0C);
        pm8001_ha->gs_tbl.pm8001_tbl.iop_tcnt           =
                                pm8001_mr32(address, 0x10);
        pm8001_ha->gs_tbl.pm8001_tbl.rsvd               =
                                pm8001_mr32(address, 0x14);
        pm8001_ha->gs_tbl.pm8001_tbl.phy_state[0]       =
                                pm8001_mr32(address, 0x18);
        pm8001_ha->gs_tbl.pm8001_tbl.phy_state[1]       =
                                pm8001_mr32(address, 0x1C);
        pm8001_ha->gs_tbl.pm8001_tbl.phy_state[2]       =
                                pm8001_mr32(address, 0x20);
        pm8001_ha->gs_tbl.pm8001_tbl.phy_state[3]       =
                                pm8001_mr32(address, 0x24);
        pm8001_ha->gs_tbl.pm8001_tbl.phy_state[4]       =
                                pm8001_mr32(address, 0x28);
        pm8001_ha->gs_tbl.pm8001_tbl.phy_state[5]       =
                                pm8001_mr32(address, 0x2C);
        pm8001_ha->gs_tbl.pm8001_tbl.phy_state[6]       =
                                pm8001_mr32(address, 0x30);
        pm8001_ha->gs_tbl.pm8001_tbl.phy_state[7]       =
                                pm8001_mr32(address, 0x34);
        pm8001_ha->gs_tbl.pm8001_tbl.gpio_input_val     =
                                pm8001_mr32(address, 0x38);
        pm8001_ha->gs_tbl.pm8001_tbl.rsvd1[0]           =
                                pm8001_mr32(address, 0x3C);
        pm8001_ha->gs_tbl.pm8001_tbl.rsvd1[1]           =
                                pm8001_mr32(address, 0x40);
        pm8001_ha->gs_tbl.pm8001_tbl.recover_err_info[0]        =
                                pm8001_mr32(address, 0x44);
        pm8001_ha->gs_tbl.pm8001_tbl.recover_err_info[1]        =
                                pm8001_mr32(address, 0x48);
        pm8001_ha->gs_tbl.pm8001_tbl.recover_err_info[2]        =
                                pm8001_mr32(address, 0x4C);
        pm8001_ha->gs_tbl.pm8001_tbl.recover_err_info[3]        =
                                pm8001_mr32(address, 0x50);
        pm8001_ha->gs_tbl.pm8001_tbl.recover_err_info[4]        =
                                pm8001_mr32(address, 0x54);
        pm8001_ha->gs_tbl.pm8001_tbl.recover_err_info[5]        =
                                pm8001_mr32(address, 0x58);
        pm8001_ha->gs_tbl.pm8001_tbl.recover_err_info[6]        =
                                pm8001_mr32(address, 0x5C);
        pm8001_ha->gs_tbl.pm8001_tbl.recover_err_info[7]        =
                                pm8001_mr32(address, 0x60);
}

/**
 * read_inbnd_queue_table - read the inbound queue table and save it.
 * @pm8001_ha: our hba card information
 */
static void read_inbnd_queue_table(struct pm8001_hba_info *pm8001_ha)
{
        int i;
        void __iomem *address = pm8001_ha->inbnd_q_tbl_addr;
        for (i = 0; i < PM8001_MAX_INB_NUM; i++) {
                u32 offset = i * 0x20;
                pm8001_ha->inbnd_q_tbl[i].pi_pci_bar =
                      get_pci_bar_index(pm8001_mr32(address, (offset + 0x14)));
                pm8001_ha->inbnd_q_tbl[i].pi_offset =
                        pm8001_mr32(address, (offset + 0x18));
        }
}

/**
 * read_outbnd_queue_table - read the outbound queue table and save it.
 * @pm8001_ha: our hba card information
 */
static void read_outbnd_queue_table(struct pm8001_hba_info *pm8001_ha)
{
        int i;
        void __iomem *address = pm8001_ha->outbnd_q_tbl_addr;
        for (i = 0; i < PM8001_MAX_OUTB_NUM; i++) {
                u32 offset = i * 0x24;
                pm8001_ha->outbnd_q_tbl[i].ci_pci_bar =
                      get_pci_bar_index(pm8001_mr32(address, (offset + 0x14)));
                pm8001_ha->outbnd_q_tbl[i].ci_offset =
                        pm8001_mr32(address, (offset + 0x18));
        }
}

/**
 * init_default_table_values - init the default table.
 * @pm8001_ha: our hba card information
 */
static void init_default_table_values(struct pm8001_hba_info *pm8001_ha)
{
        int i;
        u32 offsetib, offsetob;
        void __iomem *addressib = pm8001_ha->inbnd_q_tbl_addr;
        void __iomem *addressob = pm8001_ha->outbnd_q_tbl_addr;

        pm8001_ha->main_cfg_tbl.pm8001_tbl.inbound_q_nppd_hppd          = 0;
        pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_hw_event_pid0_3     = 0;
        pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_hw_event_pid4_7     = 0;
        pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_ncq_event_pid0_3    = 0;
        pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_ncq_event_pid4_7    = 0;
        pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_tgt_ITNexus_event_pid0_3 =
                                                                         0;
        pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_tgt_ITNexus_event_pid4_7 =
                                                                         0;
        pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_tgt_ssp_event_pid0_3 = 0;
        pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_tgt_ssp_event_pid4_7 = 0;
        pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_tgt_smp_event_pid0_3 = 0;
        pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_tgt_smp_event_pid4_7 = 0;

        pm8001_ha->main_cfg_tbl.pm8001_tbl.upper_event_log_addr         =
                pm8001_ha->memoryMap.region[AAP1].phys_addr_hi;
        pm8001_ha->main_cfg_tbl.pm8001_tbl.lower_event_log_addr         =
                pm8001_ha->memoryMap.region[AAP1].phys_addr_lo;
        pm8001_ha->main_cfg_tbl.pm8001_tbl.event_log_size               =
                PM8001_EVENT_LOG_SIZE;
        pm8001_ha->main_cfg_tbl.pm8001_tbl.event_log_option             = 0x01;
        pm8001_ha->main_cfg_tbl.pm8001_tbl.upper_iop_event_log_addr     =
                pm8001_ha->memoryMap.region[IOP].phys_addr_hi;
        pm8001_ha->main_cfg_tbl.pm8001_tbl.lower_iop_event_log_addr     =
                pm8001_ha->memoryMap.region[IOP].phys_addr_lo;
        pm8001_ha->main_cfg_tbl.pm8001_tbl.iop_event_log_size           =
                PM8001_EVENT_LOG_SIZE;
        pm8001_ha->main_cfg_tbl.pm8001_tbl.iop_event_log_option         = 0x01;
        pm8001_ha->main_cfg_tbl.pm8001_tbl.fatal_err_interrupt          = 0x01;
        for (i = 0; i < PM8001_MAX_INB_NUM; i++) {
                pm8001_ha->inbnd_q_tbl[i].element_pri_size_cnt  =
                        PM8001_MPI_QUEUE | (pm8001_ha->iomb_size << 16) | (0x00<<30);
                pm8001_ha->inbnd_q_tbl[i].upper_base_addr       =
                        pm8001_ha->memoryMap.region[IB + i].phys_addr_hi;
                pm8001_ha->inbnd_q_tbl[i].lower_base_addr       =
                pm8001_ha->memoryMap.region[IB + i].phys_addr_lo;
                pm8001_ha->inbnd_q_tbl[i].base_virt             =
                        (u8 *)pm8001_ha->memoryMap.region[IB + i].virt_ptr;
                pm8001_ha->inbnd_q_tbl[i].total_length          =
                        pm8001_ha->memoryMap.region[IB + i].total_len;
                pm8001_ha->inbnd_q_tbl[i].ci_upper_base_addr    =
                        pm8001_ha->memoryMap.region[CI + i].phys_addr_hi;
                pm8001_ha->inbnd_q_tbl[i].ci_lower_base_addr    =
                        pm8001_ha->memoryMap.region[CI + i].phys_addr_lo;
                pm8001_ha->inbnd_q_tbl[i].ci_virt               =
                        pm8001_ha->memoryMap.region[CI + i].virt_ptr;
                offsetib = i * 0x20;
                pm8001_ha->inbnd_q_tbl[i].pi_pci_bar            =
                        get_pci_bar_index(pm8001_mr32(addressib,
                                (offsetib + 0x14)));
                pm8001_ha->inbnd_q_tbl[i].pi_offset             =
                        pm8001_mr32(addressib, (offsetib + 0x18));
                pm8001_ha->inbnd_q_tbl[i].producer_idx          = 0;
                pm8001_ha->inbnd_q_tbl[i].consumer_index        = 0;
        }
        for (i = 0; i < PM8001_MAX_OUTB_NUM; i++) {
                pm8001_ha->outbnd_q_tbl[i].element_size_cnt     =
                        PM8001_MPI_QUEUE | (pm8001_ha->iomb_size << 16) | (0x01<<30);
                pm8001_ha->outbnd_q_tbl[i].upper_base_addr      =
                        pm8001_ha->memoryMap.region[OB + i].phys_addr_hi;
                pm8001_ha->outbnd_q_tbl[i].lower_base_addr      =
                        pm8001_ha->memoryMap.region[OB + i].phys_addr_lo;
                pm8001_ha->outbnd_q_tbl[i].base_virt            =
                        (u8 *)pm8001_ha->memoryMap.region[OB + i].virt_ptr;
                pm8001_ha->outbnd_q_tbl[i].total_length         =
                        pm8001_ha->memoryMap.region[OB + i].total_len;
                pm8001_ha->outbnd_q_tbl[i].pi_upper_base_addr   =
                        pm8001_ha->memoryMap.region[PI + i].phys_addr_hi;
                pm8001_ha->outbnd_q_tbl[i].pi_lower_base_addr   =
                        pm8001_ha->memoryMap.region[PI + i].phys_addr_lo;
                pm8001_ha->outbnd_q_tbl[i].interrup_vec_cnt_delay       =
                        0 | (10 << 16) | (i << 24);
                pm8001_ha->outbnd_q_tbl[i].pi_virt              =
                        pm8001_ha->memoryMap.region[PI + i].virt_ptr;
                offsetob = i * 0x24;
                pm8001_ha->outbnd_q_tbl[i].ci_pci_bar           =
                        get_pci_bar_index(pm8001_mr32(addressob,
                        offsetob + 0x14));
                pm8001_ha->outbnd_q_tbl[i].ci_offset            =
                        pm8001_mr32(addressob, (offsetob + 0x18));
                pm8001_ha->outbnd_q_tbl[i].consumer_idx         = 0;
                pm8001_ha->outbnd_q_tbl[i].producer_index       = 0;
        }
}

/**
 * update_main_config_table - update the main default table to the HBA.
 * @pm8001_ha: our hba card information
 */
static void update_main_config_table(struct pm8001_hba_info *pm8001_ha)
{
        void __iomem *address = pm8001_ha->main_cfg_tbl_addr;
        pm8001_mw32(address, 0x24,
                pm8001_ha->main_cfg_tbl.pm8001_tbl.inbound_q_nppd_hppd);
        pm8001_mw32(address, 0x28,
                pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_hw_event_pid0_3);
        pm8001_mw32(address, 0x2C,
                pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_hw_event_pid4_7);
        pm8001_mw32(address, 0x30,
                pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_ncq_event_pid0_3);
        pm8001_mw32(address, 0x34,
                pm8001_ha->main_cfg_tbl.pm8001_tbl.outbound_ncq_event_pid4_7);
        pm8001_mw32(address, 0x38,
                pm8001_ha->main_cfg_tbl.pm8001_tbl.
                                        outbound_tgt_ITNexus_event_pid0_3);
        pm8001_mw32(address, 0x3C,
                pm8001_ha->main_cfg_tbl.pm8001_tbl.
                                        outbound_tgt_ITNexus_event_pid4_7);
        pm8001_mw32(address, 0x40,
                pm8001_ha->main_cfg_tbl.pm8001_tbl.
                                        outbound_tgt_ssp_event_pid0_3);
        pm8001_mw32(address, 0x44,
                pm8001_ha->main_cfg_tbl.pm8001_tbl.
                                        outbound_tgt_ssp_event_pid4_7);
        pm8001_mw32(address, 0x48,
                pm8001_ha->main_cfg_tbl.pm8001_tbl.
                                        outbound_tgt_smp_event_pid0_3);
        pm8001_mw32(address, 0x4C,
                pm8001_ha->main_cfg_tbl.pm8001_tbl.
                                        outbound_tgt_smp_event_pid4_7);
        pm8001_mw32(address, 0x50,
                pm8001_ha->main_cfg_tbl.pm8001_tbl.upper_event_log_addr);
        pm8001_mw32(address, 0x54,
                pm8001_ha->main_cfg_tbl.pm8001_tbl.lower_event_log_addr);
        pm8001_mw32(address, 0x58,
                pm8001_ha->main_cfg_tbl.pm8001_tbl.event_log_size);
        pm8001_mw32(address, 0x5C,
                pm8001_ha->main_cfg_tbl.pm8001_tbl.event_log_option);
        pm8001_mw32(address, 0x60,
                pm8001_ha->main_cfg_tbl.pm8001_tbl.upper_iop_event_log_addr);
        pm8001_mw32(address, 0x64,
                pm8001_ha->main_cfg_tbl.pm8001_tbl.lower_iop_event_log_addr);
        pm8001_mw32(address, 0x68,
                pm8001_ha->main_cfg_tbl.pm8001_tbl.iop_event_log_size);
        pm8001_mw32(address, 0x6C,
                pm8001_ha->main_cfg_tbl.pm8001_tbl.iop_event_log_option);
        pm8001_mw32(address, 0x70,
                pm8001_ha->main_cfg_tbl.pm8001_tbl.fatal_err_interrupt);
}

/**
 * update_inbnd_queue_table - update the inbound queue table to the HBA.
 * @pm8001_ha: our hba card information
 */
static void update_inbnd_queue_table(struct pm8001_hba_info *pm8001_ha,
                                     int number)
{
        void __iomem *address = pm8001_ha->inbnd_q_tbl_addr;
        u16 offset = number * 0x20;
        pm8001_mw32(address, offset + 0x00,
                pm8001_ha->inbnd_q_tbl[number].element_pri_size_cnt);
        pm8001_mw32(address, offset + 0x04,
                pm8001_ha->inbnd_q_tbl[number].upper_base_addr);
        pm8001_mw32(address, offset + 0x08,
                pm8001_ha->inbnd_q_tbl[number].lower_base_addr);
        pm8001_mw32(address, offset + 0x0C,
                pm8001_ha->inbnd_q_tbl[number].ci_upper_base_addr);
        pm8001_mw32(address, offset + 0x10,
                pm8001_ha->inbnd_q_tbl[number].ci_lower_base_addr);
}

/**
 * update_outbnd_queue_table - update the outbound queue table to the HBA.
 * @pm8001_ha: our hba card information
 */
static void update_outbnd_queue_table(struct pm8001_hba_info *pm8001_ha,
                                      int number)
{
        void __iomem *address = pm8001_ha->outbnd_q_tbl_addr;
        u16 offset = number * 0x24;
        pm8001_mw32(address, offset + 0x00,
                pm8001_ha->outbnd_q_tbl[number].element_size_cnt);
        pm8001_mw32(address, offset + 0x04,
                pm8001_ha->outbnd_q_tbl[number].upper_base_addr);
        pm8001_mw32(address, offset + 0x08,
                pm8001_ha->outbnd_q_tbl[number].lower_base_addr);
        pm8001_mw32(address, offset + 0x0C,
                pm8001_ha->outbnd_q_tbl[number].pi_upper_base_addr);
        pm8001_mw32(address, offset + 0x10,
                pm8001_ha->outbnd_q_tbl[number].pi_lower_base_addr);
        pm8001_mw32(address, offset + 0x1C,
                pm8001_ha->outbnd_q_tbl[number].interrup_vec_cnt_delay);
}

/**
 * pm8001_bar4_shift - function is called to shift BAR base address
 * @pm8001_ha : our hba card infomation
 * @shiftValue : shifting value in memory bar.
 */
int pm8001_bar4_shift(struct pm8001_hba_info *pm8001_ha, u32 shiftValue)
{
        u32 regVal;
        unsigned long start;

        /* program the inbound AXI translation Lower Address */
        pm8001_cw32(pm8001_ha, 1, SPC_IBW_AXI_TRANSLATION_LOW, shiftValue);

        /* confirm the setting is written */
        start = jiffies + HZ; /* 1 sec */
        do {
                regVal = pm8001_cr32(pm8001_ha, 1, SPC_IBW_AXI_TRANSLATION_LOW);
        } while ((regVal != shiftValue) && time_before(jiffies, start));

        if (regVal != shiftValue) {
                PM8001_INIT_DBG(pm8001_ha,
                        pm8001_printk("TIMEOUT:SPC_IBW_AXI_TRANSLATION_LOW"
                        " = 0x%x\n", regVal));
                return -1;
        }
        return 0;
}

/**
 * mpi_set_phys_g3_with_ssc
 * @pm8001_ha: our hba card information
 * @SSCbit: set SSCbit to 0 to disable all phys ssc; 1 to enable all phys ssc.
 */
static void mpi_set_phys_g3_with_ssc(struct pm8001_hba_info *pm8001_ha,
                                     u32 SSCbit)
{
        u32 value, offset, i;
        unsigned long flags;

#define SAS2_SETTINGS_LOCAL_PHY_0_3_SHIFT_ADDR 0x00030000
#define SAS2_SETTINGS_LOCAL_PHY_4_7_SHIFT_ADDR 0x00040000
#define SAS2_SETTINGS_LOCAL_PHY_0_3_OFFSET 0x1074
#define SAS2_SETTINGS_LOCAL_PHY_4_7_OFFSET 0x1074
#define PHY_G3_WITHOUT_SSC_BIT_SHIFT 12
#define PHY_G3_WITH_SSC_BIT_SHIFT 13
#define SNW3_PHY_CAPABILITIES_PARITY 31

   /*
    * Using shifted destination address 0x3_0000:0x1074 + 0x4000*N (N=0:3)
    * Using shifted destination address 0x4_0000:0x1074 + 0x4000*(N-4) (N=4:7)
    */
        spin_lock_irqsave(&pm8001_ha->lock, flags);
        if (-1 == pm8001_bar4_shift(pm8001_ha,
                                SAS2_SETTINGS_LOCAL_PHY_0_3_SHIFT_ADDR)) {
                spin_unlock_irqrestore(&pm8001_ha->lock, flags);
                return;
        }

        for (i = 0; i < 4; i++) {
                offset = SAS2_SETTINGS_LOCAL_PHY_0_3_OFFSET + 0x4000 * i;
                pm8001_cw32(pm8001_ha, 2, offset, 0x80001501);
        }
        /* shift membase 3 for SAS2_SETTINGS_LOCAL_PHY 4 - 7 */
        if (-1 == pm8001_bar4_shift(pm8001_ha,
                                SAS2_SETTINGS_LOCAL_PHY_4_7_SHIFT_ADDR)) {
                spin_unlock_irqrestore(&pm8001_ha->lock, flags);
                return;
        }
        for (i = 4; i < 8; i++) {
                offset = SAS2_SETTINGS_LOCAL_PHY_4_7_OFFSET + 0x4000 * (i-4);
                pm8001_cw32(pm8001_ha, 2, offset, 0x80001501);
        }
        /*************************************************************
        Change the SSC upspreading value to 0x0 so that upspreading is disabled.
        Device MABC SMOD0 Controls
        Address: (via MEMBASE-III):
        Using shifted destination address 0x0_0000: with Offset 0xD8

        31:28 R/W Reserved Do not change
        27:24 R/W SAS_SMOD_SPRDUP 0000
        23:20 R/W SAS_SMOD_SPRDDN 0000
        19:0  R/W  Reserved Do not change
        Upon power-up this register will read as 0x8990c016,
        and I would like you to change the SAS_SMOD_SPRDUP bits to 0b0000
        so that the written value will be 0x8090c016.
        This will ensure only down-spreading SSC is enabled on the SPC.
        *************************************************************/
        value = pm8001_cr32(pm8001_ha, 2, 0xd8);
        pm8001_cw32(pm8001_ha, 2, 0xd8, 0x8000C016);

        /*set the shifted destination address to 0x0 to avoid error operation */
        pm8001_bar4_shift(pm8001_ha, 0x0);
        spin_unlock_irqrestore(&pm8001_ha->lock, flags);
        return;
}

/**
 * mpi_set_open_retry_interval_reg
 * @pm8001_ha: our hba card information
 * @interval - interval time for each OPEN_REJECT (RETRY). The units are in 1us.
 */
static void mpi_set_open_retry_interval_reg(struct pm8001_hba_info *pm8001_ha,
                                            u32 interval)
{
        u32 offset;
        u32 value;
        u32 i;
        unsigned long flags;

#define OPEN_RETRY_INTERVAL_PHY_0_3_SHIFT_ADDR 0x00030000
#define OPEN_RETRY_INTERVAL_PHY_4_7_SHIFT_ADDR 0x00040000
#define OPEN_RETRY_INTERVAL_PHY_0_3_OFFSET 0x30B4
#define OPEN_RETRY_INTERVAL_PHY_4_7_OFFSET 0x30B4
#define OPEN_RETRY_INTERVAL_REG_MASK 0x0000FFFF

        value = interval & OPEN_RETRY_INTERVAL_REG_MASK;
        spin_lock_irqsave(&pm8001_ha->lock, flags);
        /* shift bar and set the OPEN_REJECT(RETRY) interval time of PHY 0 -3.*/
        if (-1 == pm8001_bar4_shift(pm8001_ha,
                             OPEN_RETRY_INTERVAL_PHY_0_3_SHIFT_ADDR)) {
                spin_unlock_irqrestore(&pm8001_ha->lock, flags);
                return;
        }
        for (i = 0; i < 4; i++) {
                offset = OPEN_RETRY_INTERVAL_PHY_0_3_OFFSET + 0x4000 * i;
                pm8001_cw32(pm8001_ha, 2, offset, value);
        }

        if (-1 == pm8001_bar4_shift(pm8001_ha,
                             OPEN_RETRY_INTERVAL_PHY_4_7_SHIFT_ADDR)) {
                spin_unlock_irqrestore(&pm8001_ha->lock, flags);
                return;
        }
        for (i = 4; i < 8; i++) {
                offset = OPEN_RETRY_INTERVAL_PHY_4_7_OFFSET + 0x4000 * (i-4);
                pm8001_cw32(pm8001_ha, 2, offset, value);
        }
        /*set the shifted destination address to 0x0 to avoid error operation */
        pm8001_bar4_shift(pm8001_ha, 0x0);
        spin_unlock_irqrestore(&pm8001_ha->lock, flags);
        return;
}

/**
 * mpi_init_check - check firmware initialization status.
 * @pm8001_ha: our hba card information
 */
static int mpi_init_check(struct pm8001_hba_info *pm8001_ha)
{
        u32 max_wait_count;
        u32 value;
        u32 gst_len_mpistate;
        /* Write bit0=1 to Inbound DoorBell Register to tell the SPC FW the
        table is updated */
        pm8001_cw32(pm8001_ha, 0, MSGU_IBDB_SET, SPC_MSGU_CFG_TABLE_UPDATE);
        /* wait until Inbound DoorBell Clear Register toggled */
        max_wait_count = 1 * 1000 * 1000;/* 1 sec */
        do {
                udelay(1);
                value = pm8001_cr32(pm8001_ha, 0, MSGU_IBDB_SET);
                value &= SPC_MSGU_CFG_TABLE_UPDATE;
        } while ((value != 0) && (--max_wait_count));

        if (!max_wait_count)
                return -1;
        /* check the MPI-State for initialization */
        gst_len_mpistate =
                pm8001_mr32(pm8001_ha->general_stat_tbl_addr,
                GST_GSTLEN_MPIS_OFFSET);
        if (GST_MPI_STATE_INIT != (gst_len_mpistate & GST_MPI_STATE_MASK))
                return -1;
        /* check MPI Initialization error */
        gst_len_mpistate = gst_len_mpistate >> 16;
        if (0x0000 != gst_len_mpistate)
                return -1;
        return 0;
}

/**
 * check_fw_ready - The LLDD check if the FW is ready, if not, return error.
 * @pm8001_ha: our hba card information
 */
static int check_fw_ready(struct pm8001_hba_info *pm8001_ha)
{
        u32 value, value1;
        u32 max_wait_count;
        /* check error state */
        value = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1);
        value1 = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_2);
        /* check AAP error */
        if (SCRATCH_PAD1_ERR == (value & SCRATCH_PAD_STATE_MASK)) {
                /* error state */
                value = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_0);
                return -1;
        }

        /* check IOP error */
        if (SCRATCH_PAD2_ERR == (value1 & SCRATCH_PAD_STATE_MASK)) {
                /* error state */
                value1 = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_3);
                return -1;
        }

        /* bit 4-31 of scratch pad1 should be zeros if it is not
        in error state*/
        if (value & SCRATCH_PAD1_STATE_MASK) {
                /* error case */
                pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_0);
                return -1;
        }

        /* bit 2, 4-31 of scratch pad2 should be zeros if it is not
        in error state */
        if (value1 & SCRATCH_PAD2_STATE_MASK) {
                /* error case */
                return -1;
        }

        max_wait_count = 1 * 1000 * 1000;/* 1 sec timeout */

        /* wait until scratch pad 1 and 2 registers in ready state  */
        do {
                udelay(1);
                value = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1)
                        & SCRATCH_PAD1_RDY;
                value1 = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_2)
                        & SCRATCH_PAD2_RDY;
                if ((--max_wait_count) == 0)
                        return -1;
        } while ((value != SCRATCH_PAD1_RDY) || (value1 != SCRATCH_PAD2_RDY));
        return 0;
}

static void init_pci_device_addresses(struct pm8001_hba_info *pm8001_ha)
{
        void __iomem *base_addr;
        u32     value;
        u32     offset;
        u32     pcibar;
        u32     pcilogic;

        value = pm8001_cr32(pm8001_ha, 0, 0x44);
        offset = value & 0x03FFFFFF;
        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("Scratchpad 0 Offset: %x\n", offset));
        pcilogic = (value & 0xFC000000) >> 26;
        pcibar = get_pci_bar_index(pcilogic);
        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("Scratchpad 0 PCI BAR: %d\n", pcibar));
        pm8001_ha->main_cfg_tbl_addr = base_addr =
                pm8001_ha->io_mem[pcibar].memvirtaddr + offset;
        pm8001_ha->general_stat_tbl_addr =
                base_addr + pm8001_cr32(pm8001_ha, pcibar, offset + 0x18);
        pm8001_ha->inbnd_q_tbl_addr =
                base_addr + pm8001_cr32(pm8001_ha, pcibar, offset + 0x1C);
        pm8001_ha->outbnd_q_tbl_addr =
                base_addr + pm8001_cr32(pm8001_ha, pcibar, offset + 0x20);
}

/**
 * pm8001_chip_init - the main init function that initialize whole PM8001 chip.
 * @pm8001_ha: our hba card information
 */
static int pm8001_chip_init(struct pm8001_hba_info *pm8001_ha)
{
        u8 i = 0;
        u16 deviceid;
        pci_read_config_word(pm8001_ha->pdev, PCI_DEVICE_ID, &deviceid);
        /* 8081 controllers need BAR shift to access MPI space
        * as this is shared with BIOS data */
        if (deviceid == 0x8081 || deviceid == 0x0042) {
                if (-1 == pm8001_bar4_shift(pm8001_ha, GSM_SM_BASE)) {
                        PM8001_FAIL_DBG(pm8001_ha,
                                pm8001_printk("Shift Bar4 to 0x%x failed\n",
                                        GSM_SM_BASE));
                        return -1;
                }
        }
        /* check the firmware status */
        if (-1 == check_fw_ready(pm8001_ha)) {
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("Firmware is not ready!\n"));
                return -EBUSY;
        }

        /* Initialize pci space address eg: mpi offset */
        init_pci_device_addresses(pm8001_ha);
        init_default_table_values(pm8001_ha);
        read_main_config_table(pm8001_ha);
        read_general_status_table(pm8001_ha);
        read_inbnd_queue_table(pm8001_ha);
        read_outbnd_queue_table(pm8001_ha);
        /* update main config table ,inbound table and outbound table */
        update_main_config_table(pm8001_ha);
        for (i = 0; i < PM8001_MAX_INB_NUM; i++)
                update_inbnd_queue_table(pm8001_ha, i);
        for (i = 0; i < PM8001_MAX_OUTB_NUM; i++)
                update_outbnd_queue_table(pm8001_ha, i);
        /* 8081 controller donot require these operations */
        if (deviceid != 0x8081 && deviceid != 0x0042) {
                mpi_set_phys_g3_with_ssc(pm8001_ha, 0);
                /* 7->130ms, 34->500ms, 119->1.5s */
                mpi_set_open_retry_interval_reg(pm8001_ha, 119);
        }
        /* notify firmware update finished and check initialization status */
        if (0 == mpi_init_check(pm8001_ha)) {
                PM8001_INIT_DBG(pm8001_ha,
                        pm8001_printk("MPI initialize successful!\n"));
        } else
                return -EBUSY;
        /*This register is a 16-bit timer with a resolution of 1us. This is the
        timer used for interrupt delay/coalescing in the PCIe Application Layer.
        Zero is not a valid value. A value of 1 in the register will cause the
        interrupts to be normal. A value greater than 1 will cause coalescing
        delays.*/
        pm8001_cw32(pm8001_ha, 1, 0x0033c0, 0x1);
        pm8001_cw32(pm8001_ha, 1, 0x0033c4, 0x0);
        return 0;
}

static int mpi_uninit_check(struct pm8001_hba_info *pm8001_ha)
{
        u32 max_wait_count;
        u32 value;
        u32 gst_len_mpistate;
        u16 deviceid;
        pci_read_config_word(pm8001_ha->pdev, PCI_DEVICE_ID, &deviceid);
        if (deviceid == 0x8081 || deviceid == 0x0042) {
                if (-1 == pm8001_bar4_shift(pm8001_ha, GSM_SM_BASE)) {
                        PM8001_FAIL_DBG(pm8001_ha,
                                pm8001_printk("Shift Bar4 to 0x%x failed\n",
                                        GSM_SM_BASE));
                        return -1;
                }
        }
        init_pci_device_addresses(pm8001_ha);
        /* Write bit1=1 to Inbound DoorBell Register to tell the SPC FW the
        table is stop */
        pm8001_cw32(pm8001_ha, 0, MSGU_IBDB_SET, SPC_MSGU_CFG_TABLE_RESET);

        /* wait until Inbound DoorBell Clear Register toggled */
        max_wait_count = 1 * 1000 * 1000;/* 1 sec */
        do {
                udelay(1);
                value = pm8001_cr32(pm8001_ha, 0, MSGU_IBDB_SET);
                value &= SPC_MSGU_CFG_TABLE_RESET;
        } while ((value != 0) && (--max_wait_count));

        if (!max_wait_count) {
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("TIMEOUT:IBDB value/=0x%x\n", value));
                return -1;
        }

        /* check the MPI-State for termination in progress */
        /* wait until Inbound DoorBell Clear Register toggled */
        max_wait_count = 1 * 1000 * 1000;  /* 1 sec */
        do {
                udelay(1);
                gst_len_mpistate =
                        pm8001_mr32(pm8001_ha->general_stat_tbl_addr,
                        GST_GSTLEN_MPIS_OFFSET);
                if (GST_MPI_STATE_UNINIT ==
                        (gst_len_mpistate & GST_MPI_STATE_MASK))
                        break;
        } while (--max_wait_count);
        if (!max_wait_count) {
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk(" TIME OUT MPI State = 0x%x\n",
                                gst_len_mpistate & GST_MPI_STATE_MASK));
                return -1;
        }
        return 0;
}

/**
 * soft_reset_ready_check - Function to check FW is ready for soft reset.
 * @pm8001_ha: our hba card information
 */
static u32 soft_reset_ready_check(struct pm8001_hba_info *pm8001_ha)
{
        u32 regVal, regVal1, regVal2;
        if (mpi_uninit_check(pm8001_ha) != 0) {
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("MPI state is not ready\n"));
                return -1;
        }
        /* read the scratch pad 2 register bit 2 */
        regVal = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_2)
                & SCRATCH_PAD2_FWRDY_RST;
        if (regVal == SCRATCH_PAD2_FWRDY_RST) {
                PM8001_INIT_DBG(pm8001_ha,
                        pm8001_printk("Firmware is ready for reset .\n"));
        } else {
                unsigned long flags;
                /* Trigger NMI twice via RB6 */
                spin_lock_irqsave(&pm8001_ha->lock, flags);
                if (-1 == pm8001_bar4_shift(pm8001_ha, RB6_ACCESS_REG)) {
                        spin_unlock_irqrestore(&pm8001_ha->lock, flags);
                        PM8001_FAIL_DBG(pm8001_ha,
                                pm8001_printk("Shift Bar4 to 0x%x failed\n",
                                        RB6_ACCESS_REG));
                        return -1;
                }
                pm8001_cw32(pm8001_ha, 2, SPC_RB6_OFFSET,
                        RB6_MAGIC_NUMBER_RST);
                pm8001_cw32(pm8001_ha, 2, SPC_RB6_OFFSET, RB6_MAGIC_NUMBER_RST);
                /* wait for 100 ms */
                mdelay(100);
                regVal = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_2) &
                        SCRATCH_PAD2_FWRDY_RST;
                if (regVal != SCRATCH_PAD2_FWRDY_RST) {
                        regVal1 = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1);
                        regVal2 = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_2);
                        PM8001_FAIL_DBG(pm8001_ha,
                                pm8001_printk("TIMEOUT:MSGU_SCRATCH_PAD1"
                                "=0x%x, MSGU_SCRATCH_PAD2=0x%x\n",
                                regVal1, regVal2));
                        PM8001_FAIL_DBG(pm8001_ha,
                                pm8001_printk("SCRATCH_PAD0 value = 0x%x\n",
                                pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_0)));
                        PM8001_FAIL_DBG(pm8001_ha,
                                pm8001_printk("SCRATCH_PAD3 value = 0x%x\n",
                                pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_3)));
                        spin_unlock_irqrestore(&pm8001_ha->lock, flags);
                        return -1;
                }
                spin_unlock_irqrestore(&pm8001_ha->lock, flags);
        }
        return 0;
}

/**
 * pm8001_chip_soft_rst - soft reset the PM8001 chip, so that the clear all
 * the FW register status to the originated status.
 * @pm8001_ha: our hba card information
 */
static int
pm8001_chip_soft_rst(struct pm8001_hba_info *pm8001_ha)
{
        u32     regVal, toggleVal;
        u32     max_wait_count;
        u32     regVal1, regVal2, regVal3;
        u32     signature = 0x252acbcd; /* for host scratch pad0 */
        unsigned long flags;

        /* step1: Check FW is ready for soft reset */
        if (soft_reset_ready_check(pm8001_ha) != 0) {
                PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("FW is not ready\n"));
                return -1;
        }

        /* step 2: clear NMI status register on AAP1 and IOP, write the same
        value to clear */
        /* map 0x60000 to BAR4(0x20), BAR2(win) */
        spin_lock_irqsave(&pm8001_ha->lock, flags);
        if (-1 == pm8001_bar4_shift(pm8001_ha, MBIC_AAP1_ADDR_BASE)) {
                spin_unlock_irqrestore(&pm8001_ha->lock, flags);
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("Shift Bar4 to 0x%x failed\n",
                        MBIC_AAP1_ADDR_BASE));
                return -1;
        }
        regVal = pm8001_cr32(pm8001_ha, 2, MBIC_NMI_ENABLE_VPE0_IOP);
        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("MBIC - NMI Enable VPE0 (IOP)= 0x%x\n", regVal));
        pm8001_cw32(pm8001_ha, 2, MBIC_NMI_ENABLE_VPE0_IOP, 0x0);
        /* map 0x70000 to BAR4(0x20), BAR2(win) */
        if (-1 == pm8001_bar4_shift(pm8001_ha, MBIC_IOP_ADDR_BASE)) {
                spin_unlock_irqrestore(&pm8001_ha->lock, flags);
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("Shift Bar4 to 0x%x failed\n",
                        MBIC_IOP_ADDR_BASE));
                return -1;
        }
        regVal = pm8001_cr32(pm8001_ha, 2, MBIC_NMI_ENABLE_VPE0_AAP1);
        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("MBIC - NMI Enable VPE0 (AAP1)= 0x%x\n", regVal));
        pm8001_cw32(pm8001_ha, 2, MBIC_NMI_ENABLE_VPE0_AAP1, 0x0);

        regVal = pm8001_cr32(pm8001_ha, 1, PCIE_EVENT_INTERRUPT_ENABLE);
        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("PCIE -Event Interrupt Enable = 0x%x\n", regVal));
        pm8001_cw32(pm8001_ha, 1, PCIE_EVENT_INTERRUPT_ENABLE, 0x0);

        regVal = pm8001_cr32(pm8001_ha, 1, PCIE_EVENT_INTERRUPT);
        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("PCIE - Event Interrupt  = 0x%x\n", regVal));
        pm8001_cw32(pm8001_ha, 1, PCIE_EVENT_INTERRUPT, regVal);

        regVal = pm8001_cr32(pm8001_ha, 1, PCIE_ERROR_INTERRUPT_ENABLE);
        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("PCIE -Error Interrupt Enable = 0x%x\n", regVal));
        pm8001_cw32(pm8001_ha, 1, PCIE_ERROR_INTERRUPT_ENABLE, 0x0);

        regVal = pm8001_cr32(pm8001_ha, 1, PCIE_ERROR_INTERRUPT);
        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("PCIE - Error Interrupt = 0x%x\n", regVal));
        pm8001_cw32(pm8001_ha, 1, PCIE_ERROR_INTERRUPT, regVal);

        /* read the scratch pad 1 register bit 2 */
        regVal = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1)
                & SCRATCH_PAD1_RST;
        toggleVal = regVal ^ SCRATCH_PAD1_RST;

        /* set signature in host scratch pad0 register to tell SPC that the
        host performs the soft reset */
        pm8001_cw32(pm8001_ha, 0, MSGU_HOST_SCRATCH_PAD_0, signature);

        /* read required registers for confirmming */
        /* map 0x0700000 to BAR4(0x20), BAR2(win) */
        if (-1 == pm8001_bar4_shift(pm8001_ha, GSM_ADDR_BASE)) {
                spin_unlock_irqrestore(&pm8001_ha->lock, flags);
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("Shift Bar4 to 0x%x failed\n",
                        GSM_ADDR_BASE));
                return -1;
        }
        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("GSM 0x0(0x00007b88)-GSM Configuration and"
                " Reset = 0x%x\n",
                pm8001_cr32(pm8001_ha, 2, GSM_CONFIG_RESET)));

        /* step 3: host read GSM Configuration and Reset register */
        regVal = pm8001_cr32(pm8001_ha, 2, GSM_CONFIG_RESET);
        /* Put those bits to low */
        /* GSM XCBI offset = 0x70 0000
        0x00 Bit 13 COM_SLV_SW_RSTB 1
        0x00 Bit 12 QSSP_SW_RSTB 1
        0x00 Bit 11 RAAE_SW_RSTB 1
        0x00 Bit 9 RB_1_SW_RSTB 1
        0x00 Bit 8 SM_SW_RSTB 1
        */
        regVal &= ~(0x00003b00);
        /* host write GSM Configuration and Reset register */
        pm8001_cw32(pm8001_ha, 2, GSM_CONFIG_RESET, regVal);
        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("GSM 0x0 (0x00007b88 ==> 0x00004088) - GSM "
                "Configuration and Reset is set to = 0x%x\n",
                pm8001_cr32(pm8001_ha, 2, GSM_CONFIG_RESET)));

        /* step 4: */
        /* disable GSM - Read Address Parity Check */
        regVal1 = pm8001_cr32(pm8001_ha, 2, GSM_READ_ADDR_PARITY_CHECK);
        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("GSM 0x700038 - Read Address Parity Check "
                "Enable = 0x%x\n", regVal1));
        pm8001_cw32(pm8001_ha, 2, GSM_READ_ADDR_PARITY_CHECK, 0x0);
        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("GSM 0x700038 - Read Address Parity Check Enable"
                "is set to = 0x%x\n",
                pm8001_cr32(pm8001_ha, 2, GSM_READ_ADDR_PARITY_CHECK)));

        /* disable GSM - Write Address Parity Check */
        regVal2 = pm8001_cr32(pm8001_ha, 2, GSM_WRITE_ADDR_PARITY_CHECK);
        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("GSM 0x700040 - Write Address Parity Check"
                " Enable = 0x%x\n", regVal2));
        pm8001_cw32(pm8001_ha, 2, GSM_WRITE_ADDR_PARITY_CHECK, 0x0);
        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("GSM 0x700040 - Write Address Parity Check "
                "Enable is set to = 0x%x\n",
                pm8001_cr32(pm8001_ha, 2, GSM_WRITE_ADDR_PARITY_CHECK)));

        /* disable GSM - Write Data Parity Check */
        regVal3 = pm8001_cr32(pm8001_ha, 2, GSM_WRITE_DATA_PARITY_CHECK);
        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("GSM 0x300048 - Write Data Parity Check"
                " Enable = 0x%x\n", regVal3));
        pm8001_cw32(pm8001_ha, 2, GSM_WRITE_DATA_PARITY_CHECK, 0x0);
        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("GSM 0x300048 - Write Data Parity Check Enable"
                "is set to = 0x%x\n",
        pm8001_cr32(pm8001_ha, 2, GSM_WRITE_DATA_PARITY_CHECK)));

        /* step 5: delay 10 usec */
        udelay(10);
        /* step 5-b: set GPIO-0 output control to tristate anyway */
        if (-1 == pm8001_bar4_shift(pm8001_ha, GPIO_ADDR_BASE)) {
                spin_unlock_irqrestore(&pm8001_ha->lock, flags);
                PM8001_INIT_DBG(pm8001_ha,
                                pm8001_printk("Shift Bar4 to 0x%x failed\n",
                                GPIO_ADDR_BASE));
                return -1;
        }
        regVal = pm8001_cr32(pm8001_ha, 2, GPIO_GPIO_0_0UTPUT_CTL_OFFSET);
                PM8001_INIT_DBG(pm8001_ha,
                                pm8001_printk("GPIO Output Control Register:"
                                " = 0x%x\n", regVal));
        /* set GPIO-0 output control to tri-state */
        regVal &= 0xFFFFFFFC;
        pm8001_cw32(pm8001_ha, 2, GPIO_GPIO_0_0UTPUT_CTL_OFFSET, regVal);

        /* Step 6: Reset the IOP and AAP1 */
        /* map 0x00000 to BAR4(0x20), BAR2(win) */
        if (-1 == pm8001_bar4_shift(pm8001_ha, SPC_TOP_LEVEL_ADDR_BASE)) {
                spin_unlock_irqrestore(&pm8001_ha->lock, flags);
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("SPC Shift Bar4 to 0x%x failed\n",
                        SPC_TOP_LEVEL_ADDR_BASE));
                return -1;
        }
        regVal = pm8001_cr32(pm8001_ha, 2, SPC_REG_RESET);
        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("Top Register before resetting IOP/AAP1"
                ":= 0x%x\n", regVal));
        regVal &= ~(SPC_REG_RESET_PCS_IOP_SS | SPC_REG_RESET_PCS_AAP1_SS);
        pm8001_cw32(pm8001_ha, 2, SPC_REG_RESET, regVal);

        /* step 7: Reset the BDMA/OSSP */
        regVal = pm8001_cr32(pm8001_ha, 2, SPC_REG_RESET);
        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("Top Register before resetting BDMA/OSSP"
                ": = 0x%x\n", regVal));
        regVal &= ~(SPC_REG_RESET_BDMA_CORE | SPC_REG_RESET_OSSP);
        pm8001_cw32(pm8001_ha, 2, SPC_REG_RESET, regVal);

        /* step 8: delay 10 usec */
        udelay(10);

        /* step 9: bring the BDMA and OSSP out of reset */
        regVal = pm8001_cr32(pm8001_ha, 2, SPC_REG_RESET);
        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("Top Register before bringing up BDMA/OSSP"

                ":= 0x%x\n", regVal));
        regVal |= (SPC_REG_RESET_BDMA_CORE | SPC_REG_RESET_OSSP);
        pm8001_cw32(pm8001_ha, 2, SPC_REG_RESET, regVal);

        /* step 10: delay 10 usec */
        udelay(10);

        /* step 11: reads and sets the GSM Configuration and Reset Register */
        /* map 0x0700000 to BAR4(0x20), BAR2(win) */
        if (-1 == pm8001_bar4_shift(pm8001_ha, GSM_ADDR_BASE)) {
                spin_unlock_irqrestore(&pm8001_ha->lock, flags);
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("SPC Shift Bar4 to 0x%x failed\n",
                        GSM_ADDR_BASE));
                return -1;
        }
        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("GSM 0x0 (0x00007b88)-GSM Configuration and "
                "Reset = 0x%x\n", pm8001_cr32(pm8001_ha, 2, GSM_CONFIG_RESET)));
        regVal = pm8001_cr32(pm8001_ha, 2, GSM_CONFIG_RESET);
        /* Put those bits to high */
        /* GSM XCBI offset = 0x70 0000
        0x00 Bit 13 COM_SLV_SW_RSTB 1
        0x00 Bit 12 QSSP_SW_RSTB 1
        0x00 Bit 11 RAAE_SW_RSTB 1
        0x00 Bit 9   RB_1_SW_RSTB 1
        0x00 Bit 8   SM_SW_RSTB 1
        */
        regVal |= (GSM_CONFIG_RESET_VALUE);
        pm8001_cw32(pm8001_ha, 2, GSM_CONFIG_RESET, regVal);
        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("GSM (0x00004088 ==> 0x00007b88) - GSM"
                " Configuration and Reset is set to = 0x%x\n",
                pm8001_cr32(pm8001_ha, 2, GSM_CONFIG_RESET)));

        /* step 12: Restore GSM - Read Address Parity Check */
        regVal = pm8001_cr32(pm8001_ha, 2, GSM_READ_ADDR_PARITY_CHECK);
        /* just for debugging */
        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("GSM 0x700038 - Read Address Parity Check Enable"
                " = 0x%x\n", regVal));
        pm8001_cw32(pm8001_ha, 2, GSM_READ_ADDR_PARITY_CHECK, regVal1);
        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("GSM 0x700038 - Read Address Parity"
                " Check Enable is set to = 0x%x\n",
                pm8001_cr32(pm8001_ha, 2, GSM_READ_ADDR_PARITY_CHECK)));
        /* Restore GSM - Write Address Parity Check */
        regVal = pm8001_cr32(pm8001_ha, 2, GSM_WRITE_ADDR_PARITY_CHECK);
        pm8001_cw32(pm8001_ha, 2, GSM_WRITE_ADDR_PARITY_CHECK, regVal2);
        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("GSM 0x700040 - Write Address Parity Check"
                " Enable is set to = 0x%x\n",
                pm8001_cr32(pm8001_ha, 2, GSM_WRITE_ADDR_PARITY_CHECK)));
        /* Restore GSM - Write Data Parity Check */
        regVal = pm8001_cr32(pm8001_ha, 2, GSM_WRITE_DATA_PARITY_CHECK);
        pm8001_cw32(pm8001_ha, 2, GSM_WRITE_DATA_PARITY_CHECK, regVal3);
        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("GSM 0x700048 - Write Data Parity Check Enable"
                "is set to = 0x%x\n",
                pm8001_cr32(pm8001_ha, 2, GSM_WRITE_DATA_PARITY_CHECK)));

        /* step 13: bring the IOP and AAP1 out of reset */
        /* map 0x00000 to BAR4(0x20), BAR2(win) */
        if (-1 == pm8001_bar4_shift(pm8001_ha, SPC_TOP_LEVEL_ADDR_BASE)) {
                spin_unlock_irqrestore(&pm8001_ha->lock, flags);
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("Shift Bar4 to 0x%x failed\n",
                        SPC_TOP_LEVEL_ADDR_BASE));
                return -1;
        }
        regVal = pm8001_cr32(pm8001_ha, 2, SPC_REG_RESET);
        regVal |= (SPC_REG_RESET_PCS_IOP_SS | SPC_REG_RESET_PCS_AAP1_SS);
        pm8001_cw32(pm8001_ha, 2, SPC_REG_RESET, regVal);

        /* step 14: delay 10 usec - Normal Mode */
        udelay(10);
        /* check Soft Reset Normal mode or Soft Reset HDA mode */
        if (signature == SPC_SOFT_RESET_SIGNATURE) {
                /* step 15 (Normal Mode): wait until scratch pad1 register
                bit 2 toggled */
                max_wait_count = 2 * 1000 * 1000;/* 2 sec */
                do {
                        udelay(1);
                        regVal = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1) &
                                SCRATCH_PAD1_RST;
                } while ((regVal != toggleVal) && (--max_wait_count));

                if (!max_wait_count) {
                        regVal = pm8001_cr32(pm8001_ha, 0,
                                MSGU_SCRATCH_PAD_1);
                        PM8001_FAIL_DBG(pm8001_ha,
                                pm8001_printk("TIMEOUT : ToggleVal 0x%x,"
                                "MSGU_SCRATCH_PAD1 = 0x%x\n",
                                toggleVal, regVal));
                        PM8001_FAIL_DBG(pm8001_ha,
                                pm8001_printk("SCRATCH_PAD0 value = 0x%x\n",
                                pm8001_cr32(pm8001_ha, 0,
                                MSGU_SCRATCH_PAD_0)));
                        PM8001_FAIL_DBG(pm8001_ha,
                                pm8001_printk("SCRATCH_PAD2 value = 0x%x\n",
                                pm8001_cr32(pm8001_ha, 0,
                                MSGU_SCRATCH_PAD_2)));
                        PM8001_FAIL_DBG(pm8001_ha,
                                pm8001_printk("SCRATCH_PAD3 value = 0x%x\n",
                                pm8001_cr32(pm8001_ha, 0,
                                MSGU_SCRATCH_PAD_3)));
                        spin_unlock_irqrestore(&pm8001_ha->lock, flags);
                        return -1;
                }

                /* step 16 (Normal) - Clear ODMR and ODCR */
                pm8001_cw32(pm8001_ha, 0, MSGU_ODCR, ODCR_CLEAR_ALL);
                pm8001_cw32(pm8001_ha, 0, MSGU_ODMR, ODMR_CLEAR_ALL);

                /* step 17 (Normal Mode): wait for the FW and IOP to get
                ready - 1 sec timeout */
                /* Wait for the SPC Configuration Table to be ready */
                if (check_fw_ready(pm8001_ha) == -1) {
                        regVal = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1);
                        /* return error if MPI Configuration Table not ready */
                        PM8001_INIT_DBG(pm8001_ha,
                                pm8001_printk("FW not ready SCRATCH_PAD1"
                                " = 0x%x\n", regVal));
                        regVal = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_2);
                        /* return error if MPI Configuration Table not ready */
                        PM8001_INIT_DBG(pm8001_ha,
                                pm8001_printk("FW not ready SCRATCH_PAD2"
                                " = 0x%x\n", regVal));
                        PM8001_INIT_DBG(pm8001_ha,
                                pm8001_printk("SCRATCH_PAD0 value = 0x%x\n",
                                pm8001_cr32(pm8001_ha, 0,
                                MSGU_SCRATCH_PAD_0)));
                        PM8001_INIT_DBG(pm8001_ha,
                                pm8001_printk("SCRATCH_PAD3 value = 0x%x\n",
                                pm8001_cr32(pm8001_ha, 0,
                                MSGU_SCRATCH_PAD_3)));
                        spin_unlock_irqrestore(&pm8001_ha->lock, flags);
                        return -1;
                }
        }
        pm8001_bar4_shift(pm8001_ha, 0);
        spin_unlock_irqrestore(&pm8001_ha->lock, flags);

        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("SPC soft reset Complete\n"));
        return 0;
}

static void pm8001_hw_chip_rst(struct pm8001_hba_info *pm8001_ha)
{
        u32 i;
        u32 regVal;
        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("chip reset start\n"));

        /* do SPC chip reset. */
        regVal = pm8001_cr32(pm8001_ha, 1, SPC_REG_RESET);
        regVal &= ~(SPC_REG_RESET_DEVICE);
        pm8001_cw32(pm8001_ha, 1, SPC_REG_RESET, regVal);

        /* delay 10 usec */
        udelay(10);

        /* bring chip reset out of reset */
        regVal = pm8001_cr32(pm8001_ha, 1, SPC_REG_RESET);
        regVal |= SPC_REG_RESET_DEVICE;
        pm8001_cw32(pm8001_ha, 1, SPC_REG_RESET, regVal);

        /* delay 10 usec */
        udelay(10);

        /* wait for 20 msec until the firmware gets reloaded */
        i = 20;
        do {
                mdelay(1);
        } while ((--i) != 0);

        PM8001_INIT_DBG(pm8001_ha,
                pm8001_printk("chip reset finished\n"));
}

/**
 * pm8001_chip_iounmap - which maped when initialized.
 * @pm8001_ha: our hba card information
 */
void pm8001_chip_iounmap(struct pm8001_hba_info *pm8001_ha)
{
        s8 bar, logical = 0;
        for (bar = 0; bar < 6; bar++) {
                /*
                ** logical BARs for SPC:
                ** bar 0 and 1 - logical BAR0
                ** bar 2 and 3 - logical BAR1
                ** bar4 - logical BAR2
                ** bar5 - logical BAR3
                ** Skip the appropriate assignments:
                */
                if ((bar == 1) || (bar == 3))
                        continue;
                if (pm8001_ha->io_mem[logical].memvirtaddr) {
                        iounmap(pm8001_ha->io_mem[logical].memvirtaddr);
                        logical++;
                }
        }
}

/**
 * pm8001_chip_interrupt_enable - enable PM8001 chip interrupt
 * @pm8001_ha: our hba card information
 */
static void
pm8001_chip_intx_interrupt_enable(struct pm8001_hba_info *pm8001_ha)
{
        pm8001_cw32(pm8001_ha, 0, MSGU_ODMR, ODMR_CLEAR_ALL);
        pm8001_cw32(pm8001_ha, 0, MSGU_ODCR, ODCR_CLEAR_ALL);
}

 /**
  * pm8001_chip_intx_interrupt_disable- disable PM8001 chip interrupt
  * @pm8001_ha: our hba card information
  */
static void
pm8001_chip_intx_interrupt_disable(struct pm8001_hba_info *pm8001_ha)
{
        pm8001_cw32(pm8001_ha, 0, MSGU_ODMR, ODMR_MASK_ALL);
}

/**
 * pm8001_chip_msix_interrupt_enable - enable PM8001 chip interrupt
 * @pm8001_ha: our hba card information
 */
static void
pm8001_chip_msix_interrupt_enable(struct pm8001_hba_info *pm8001_ha,
        u32 int_vec_idx)
{
        u32 msi_index;
        u32 value;
        msi_index = int_vec_idx * MSIX_TABLE_ELEMENT_SIZE;
        msi_index += MSIX_TABLE_BASE;
        pm8001_cw32(pm8001_ha, 0, msi_index, MSIX_INTERRUPT_ENABLE);
        value = (1 << int_vec_idx);
        pm8001_cw32(pm8001_ha, 0,  MSGU_ODCR, value);

}

/**
 * pm8001_chip_msix_interrupt_disable - disable PM8001 chip interrupt
 * @pm8001_ha: our hba card information
 */
static void
pm8001_chip_msix_interrupt_disable(struct pm8001_hba_info *pm8001_ha,
        u32 int_vec_idx)
{
        u32 msi_index;
        msi_index = int_vec_idx * MSIX_TABLE_ELEMENT_SIZE;
        msi_index += MSIX_TABLE_BASE;
        pm8001_cw32(pm8001_ha, 0,  msi_index, MSIX_INTERRUPT_DISABLE);
}

/**
 * pm8001_chip_interrupt_enable - enable PM8001 chip interrupt
 * @pm8001_ha: our hba card information
 */
static void
pm8001_chip_interrupt_enable(struct pm8001_hba_info *pm8001_ha, u8 vec)
{
#ifdef PM8001_USE_MSIX
        pm8001_chip_msix_interrupt_enable(pm8001_ha, 0);
        return;
#endif
        pm8001_chip_intx_interrupt_enable(pm8001_ha);

}

/**
 * pm8001_chip_intx_interrupt_disable- disable PM8001 chip interrupt
 * @pm8001_ha: our hba card information
 */
static void
pm8001_chip_interrupt_disable(struct pm8001_hba_info *pm8001_ha, u8 vec)
{
#ifdef PM8001_USE_MSIX
        pm8001_chip_msix_interrupt_disable(pm8001_ha, 0);
        return;
#endif
        pm8001_chip_intx_interrupt_disable(pm8001_ha);

}

/**
 * pm8001_mpi_msg_free_get - get the free message buffer for transfer
 * inbound queue.
 * @circularQ: the inbound queue  we want to transfer to HBA.
 * @messageSize: the message size of this transfer, normally it is 64 bytes
 * @messagePtr: the pointer to message.
 */
int pm8001_mpi_msg_free_get(struct inbound_queue_table *circularQ,
                            u16 messageSize, void **messagePtr)
{
        u32 offset, consumer_index;
        struct mpi_msg_hdr *msgHeader;
        u8 bcCount = 1; /* only support single buffer */

        /* Checks is the requested message size can be allocated in this queue*/
        if (messageSize > IOMB_SIZE_SPCV) {
                *messagePtr = NULL;
                return -1;
        }

        /* Stores the new consumer index */
        consumer_index = pm8001_read_32(circularQ->ci_virt);
        circularQ->consumer_index = cpu_to_le32(consumer_index);
        if (((circularQ->producer_idx + bcCount) % PM8001_MPI_QUEUE) ==
                le32_to_cpu(circularQ->consumer_index)) {
                *messagePtr = NULL;
                return -1;
        }
        /* get memory IOMB buffer address */
        offset = circularQ->producer_idx * messageSize;
        /* increment to next bcCount element */
        circularQ->producer_idx = (circularQ->producer_idx + bcCount)
                                % PM8001_MPI_QUEUE;
        /* Adds that distance to the base of the region virtual address plus
        the message header size*/
        msgHeader = (struct mpi_msg_hdr *)(circularQ->base_virt + offset);
        *messagePtr = ((void *)msgHeader) + sizeof(struct mpi_msg_hdr);
        return 0;
}

/**
 * pm8001_mpi_build_cmd- build the message queue for transfer, update the PI to
 * FW to tell the fw to get this message from IOMB.
 * @pm8001_ha: our hba card information
 * @circularQ: the inbound queue we want to transfer to HBA.
 * @opCode: the operation code represents commands which LLDD and fw recognized.
 * @payload: the command payload of each operation command.
 */
int pm8001_mpi_build_cmd(struct pm8001_hba_info *pm8001_ha,
                         struct inbound_queue_table *circularQ,
                         u32 opCode, void *payload, u32 responseQueue)
{
        u32 Header = 0, hpriority = 0, bc = 1, category = 0x02;
        void *pMessage;

        if (pm8001_mpi_msg_free_get(circularQ, pm8001_ha->iomb_size,
                &pMessage) < 0) {
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("No free mpi buffer\n"));
                return -ENOMEM;
        }
        BUG_ON(!payload);
        /*Copy to the payload*/
        memcpy(pMessage, payload, (pm8001_ha->iomb_size -
                                sizeof(struct mpi_msg_hdr)));

        /*Build the header*/
        Header = ((1 << 31) | (hpriority << 30) | ((bc & 0x1f) << 24)
                | ((responseQueue & 0x3F) << 16)
                | ((category & 0xF) << 12) | (opCode & 0xFFF));

        pm8001_write_32((pMessage - 4), 0, cpu_to_le32(Header));
        /*Update the PI to the firmware*/
        pm8001_cw32(pm8001_ha, circularQ->pi_pci_bar,
                circularQ->pi_offset, circularQ->producer_idx);
        PM8001_IO_DBG(pm8001_ha,
                pm8001_printk("INB Q %x OPCODE:%x , UPDATED PI=%d CI=%d\n",
                        responseQueue, opCode, circularQ->producer_idx,
                        circularQ->consumer_index));
        return 0;
}

u32 pm8001_mpi_msg_free_set(struct pm8001_hba_info *pm8001_ha, void *pMsg,
                            struct outbound_queue_table *circularQ, u8 bc)
{
        u32 producer_index;
        struct mpi_msg_hdr *msgHeader;
        struct mpi_msg_hdr *pOutBoundMsgHeader;

        msgHeader = (struct mpi_msg_hdr *)(pMsg - sizeof(struct mpi_msg_hdr));
        pOutBoundMsgHeader = (struct mpi_msg_hdr *)(circularQ->base_virt +
                                circularQ->consumer_idx * pm8001_ha->iomb_size);
        if (pOutBoundMsgHeader != msgHeader) {
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("consumer_idx = %d msgHeader = %p\n",
                        circularQ->consumer_idx, msgHeader));

                /* Update the producer index from SPC */
                producer_index = pm8001_read_32(circularQ->pi_virt);
                circularQ->producer_index = cpu_to_le32(producer_index);
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("consumer_idx = %d producer_index = %d"
                        "msgHeader = %p\n", circularQ->consumer_idx,
                        circularQ->producer_index, msgHeader));
                return 0;
        }
        /* free the circular queue buffer elements associated with the message*/
        circularQ->consumer_idx = (circularQ->consumer_idx + bc)
                                % PM8001_MPI_QUEUE;
        /* update the CI of outbound queue */
        pm8001_cw32(pm8001_ha, circularQ->ci_pci_bar, circularQ->ci_offset,
                circularQ->consumer_idx);
        /* Update the producer index from SPC*/
        producer_index = pm8001_read_32(circularQ->pi_virt);
        circularQ->producer_index = cpu_to_le32(producer_index);
        PM8001_IO_DBG(pm8001_ha,
                pm8001_printk(" CI=%d PI=%d\n", circularQ->consumer_idx,
                circularQ->producer_index));
        return 0;
}

/**
 * pm8001_mpi_msg_consume- get the MPI message from outbound queue
 * message table.
 * @pm8001_ha: our hba card information
 * @circularQ: the outbound queue  table.
 * @messagePtr1: the message contents of this outbound message.
 * @pBC: the message size.
 */
u32 pm8001_mpi_msg_consume(struct pm8001_hba_info *pm8001_ha,
                           struct outbound_queue_table *circularQ,
                           void **messagePtr1, u8 *pBC)
{
        struct mpi_msg_hdr      *msgHeader;
        __le32  msgHeader_tmp;
        u32 header_tmp;
        do {
                /* If there are not-yet-delivered messages ... */
                if (le32_to_cpu(circularQ->producer_index)
                        != circularQ->consumer_idx) {
                        /*Get the pointer to the circular queue buffer element*/
                        msgHeader = (struct mpi_msg_hdr *)
                                (circularQ->base_virt +
                                circularQ->consumer_idx * pm8001_ha->iomb_size);
                        /* read header */
                        header_tmp = pm8001_read_32(msgHeader);
                        msgHeader_tmp = cpu_to_le32(header_tmp);
                        if (0 != (le32_to_cpu(msgHeader_tmp) & 0x80000000)) {
                                if (OPC_OUB_SKIP_ENTRY !=
                                        (le32_to_cpu(msgHeader_tmp) & 0xfff)) {
                                        *messagePtr1 =
                                                ((u8 *)msgHeader) +
                                                sizeof(struct mpi_msg_hdr);
                                        *pBC = (u8)((le32_to_cpu(msgHeader_tmp)
                                                >> 24) & 0x1f);
                                        PM8001_IO_DBG(pm8001_ha,
                                                pm8001_printk(": CI=%d PI=%d "
                                                "msgHeader=%x\n",
                                                circularQ->consumer_idx,
                                                circularQ->producer_index,
                                                msgHeader_tmp));
                                        return MPI_IO_STATUS_SUCCESS;
                                } else {
                                        circularQ->consumer_idx =
                                                (circularQ->consumer_idx +
                                                ((le32_to_cpu(msgHeader_tmp)
                                                 >> 24) & 0x1f))
                                                        % PM8001_MPI_QUEUE;
                                        msgHeader_tmp = 0;
                                        pm8001_write_32(msgHeader, 0, 0);
                                        /* update the CI of outbound queue */
                                        pm8001_cw32(pm8001_ha,
                                                circularQ->ci_pci_bar,
                                                circularQ->ci_offset,
                                                circularQ->consumer_idx);
                                }
                        } else {
                                circularQ->consumer_idx =
                                        (circularQ->consumer_idx +
                                        ((le32_to_cpu(msgHeader_tmp) >> 24) &
                                        0x1f)) % PM8001_MPI_QUEUE;
                                msgHeader_tmp = 0;
                                pm8001_write_32(msgHeader, 0, 0);
                                /* update the CI of outbound queue */
                                pm8001_cw32(pm8001_ha, circularQ->ci_pci_bar,
                                        circularQ->ci_offset,
                                        circularQ->consumer_idx);
                                return MPI_IO_STATUS_FAIL;
                        }
                } else {
                        u32 producer_index;
                        void *pi_virt = circularQ->pi_virt;
                        /* Update the producer index from SPC */
                        producer_index = pm8001_read_32(pi_virt);
                        circularQ->producer_index = cpu_to_le32(producer_index);
                }
        } while (le32_to_cpu(circularQ->producer_index) !=
                circularQ->consumer_idx);
        /* while we don't have any more not-yet-delivered message */
        /* report empty */
        return MPI_IO_STATUS_BUSY;
}

void pm8001_work_fn(struct work_struct *work)
{
        struct pm8001_work *pw = container_of(work, struct pm8001_work, work);
        struct pm8001_device *pm8001_dev;
        struct domain_device *dev;

        /*
         * So far, all users of this stash an associated structure here.
         * If we get here, and this pointer is null, then the action
         * was cancelled. This nullification happens when the device
         * goes away.
         */
        pm8001_dev = pw->data; /* Most stash device structure */
        if ((pm8001_dev == NULL)
         || ((pw->handler != IO_XFER_ERROR_BREAK)
          && (pm8001_dev->dev_type == SAS_PHY_UNUSED))) {
                kfree(pw);
                return;
        }

        switch (pw->handler) {
        case IO_XFER_ERROR_BREAK:
        {       /* This one stashes the sas_task instead */
                struct sas_task *t = (struct sas_task *)pm8001_dev;
                u32 tag;
                struct pm8001_ccb_info *ccb;
                struct pm8001_hba_info *pm8001_ha = pw->pm8001_ha;
                unsigned long flags, flags1;
                struct task_status_struct *ts;
                int i;

                if (pm8001_query_task(t) == TMF_RESP_FUNC_SUCC)
                        break; /* Task still on lu */
                spin_lock_irqsave(&pm8001_ha->lock, flags);

                spin_lock_irqsave(&t->task_state_lock, flags1);
                if (unlikely((t->task_state_flags & SAS_TASK_STATE_DONE))) {
                        spin_unlock_irqrestore(&t->task_state_lock, flags1);
                        spin_unlock_irqrestore(&pm8001_ha->lock, flags);
                        break; /* Task got completed by another */
                }
                spin_unlock_irqrestore(&t->task_state_lock, flags1);

                /* Search for a possible ccb that matches the task */
                for (i = 0; ccb = NULL, i < PM8001_MAX_CCB; i++) {
                        ccb = &pm8001_ha->ccb_info[i];
                        tag = ccb->ccb_tag;
                        if ((tag != 0xFFFFFFFF) && (ccb->task == t))
                                break;
                }
                if (!ccb) {
                        spin_unlock_irqrestore(&pm8001_ha->lock, flags);
                        break; /* Task got freed by another */
                }
                ts = &t->task_status;
                ts->resp = SAS_TASK_COMPLETE;
                /* Force the midlayer to retry */
                ts->stat = SAS_QUEUE_FULL;
                pm8001_dev = ccb->device;
                if (pm8001_dev)
                        pm8001_dev->running_req--;
                spin_lock_irqsave(&t->task_state_lock, flags1);
                t->task_state_flags &= ~SAS_TASK_STATE_PENDING;
                t->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
                t->task_state_flags |= SAS_TASK_STATE_DONE;
                if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) {
                        spin_unlock_irqrestore(&t->task_state_lock, flags1);
                        PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("task 0x%p"
                                " done with event 0x%x resp 0x%x stat 0x%x but"
                                " aborted by upper layer!\n",
                                t, pw->handler, ts->resp, ts->stat));
                        pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
                        spin_unlock_irqrestore(&pm8001_ha->lock, flags);
                } else {
                        spin_unlock_irqrestore(&t->task_state_lock, flags1);
                        pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
                        mb();/* in order to force CPU ordering */
                        spin_unlock_irqrestore(&pm8001_ha->lock, flags);
                        t->task_done(t);
                }
        }       break;
        case IO_XFER_OPEN_RETRY_TIMEOUT:
        {       /* This one stashes the sas_task instead */
                struct sas_task *t = (struct sas_task *)pm8001_dev;
                u32 tag;
                struct pm8001_ccb_info *ccb;
                struct pm8001_hba_info *pm8001_ha = pw->pm8001_ha;
                unsigned long flags, flags1;
                int i, ret = 0;

                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n"));

                ret = pm8001_query_task(t);

                PM8001_IO_DBG(pm8001_ha,
                        switch (ret) {
                        case TMF_RESP_FUNC_SUCC:
                                pm8001_printk("...Task on lu\n");
                                break;

                        case TMF_RESP_FUNC_COMPLETE:
                                pm8001_printk("...Task NOT on lu\n");
                                break;

                        default:
                                pm8001_printk("...query task failed!!!\n");
                                break;
                        });

                spin_lock_irqsave(&pm8001_ha->lock, flags);

                spin_lock_irqsave(&t->task_state_lock, flags1);

                if (unlikely((t->task_state_flags & SAS_TASK_STATE_DONE))) {
                        spin_unlock_irqrestore(&t->task_state_lock, flags1);
                        spin_unlock_irqrestore(&pm8001_ha->lock, flags);
                        if (ret == TMF_RESP_FUNC_SUCC) /* task on lu */
                                (void)pm8001_abort_task(t);
                        break; /* Task got completed by another */
                }

                spin_unlock_irqrestore(&t->task_state_lock, flags1);

                /* Search for a possible ccb that matches the task */
                for (i = 0; ccb = NULL, i < PM8001_MAX_CCB; i++) {
                        ccb = &pm8001_ha->ccb_info[i];
                        tag = ccb->ccb_tag;
                        if ((tag != 0xFFFFFFFF) && (ccb->task == t))
                                break;
                }
                if (!ccb) {
                        spin_unlock_irqrestore(&pm8001_ha->lock, flags);
                        if (ret == TMF_RESP_FUNC_SUCC) /* task on lu */
                                (void)pm8001_abort_task(t);
                        break; /* Task got freed by another */
                }

                pm8001_dev = ccb->device;
                dev = pm8001_dev->sas_device;

                switch (ret) {
                case TMF_RESP_FUNC_SUCC: /* task on lu */
                        ccb->open_retry = 1; /* Snub completion */
                        spin_unlock_irqrestore(&pm8001_ha->lock, flags);
                        ret = pm8001_abort_task(t);
                        ccb->open_retry = 0;
                        switch (ret) {
                        case TMF_RESP_FUNC_SUCC:
                        case TMF_RESP_FUNC_COMPLETE:
                                break;
                        default: /* device misbehavior */
                                ret = TMF_RESP_FUNC_FAILED;
                                PM8001_IO_DBG(pm8001_ha,
                                        pm8001_printk("...Reset phy\n"));
                                pm8001_I_T_nexus_reset(dev);
                                break;
                        }
                        break;

                case TMF_RESP_FUNC_COMPLETE: /* task not on lu */
                        spin_unlock_irqrestore(&pm8001_ha->lock, flags);
                        /* Do we need to abort the task locally? */
                        break;

                default: /* device misbehavior */
                        spin_unlock_irqrestore(&pm8001_ha->lock, flags);
                        ret = TMF_RESP_FUNC_FAILED;
                        PM8001_IO_DBG(pm8001_ha,
                                pm8001_printk("...Reset phy\n"));
                        pm8001_I_T_nexus_reset(dev);
                }

                if (ret == TMF_RESP_FUNC_FAILED)
                        t = NULL;
                pm8001_open_reject_retry(pm8001_ha, t, pm8001_dev);
                PM8001_IO_DBG(pm8001_ha, pm8001_printk("...Complete\n"));
        }       break;
        case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS:
                dev = pm8001_dev->sas_device;
                pm8001_I_T_nexus_event_handler(dev);
                break;
        case IO_OPEN_CNX_ERROR_STP_RESOURCES_BUSY:
                dev = pm8001_dev->sas_device;
                pm8001_I_T_nexus_reset(dev);
                break;
        case IO_DS_IN_ERROR:
                dev = pm8001_dev->sas_device;
                pm8001_I_T_nexus_reset(dev);
                break;
        case IO_DS_NON_OPERATIONAL:
                dev = pm8001_dev->sas_device;
                pm8001_I_T_nexus_reset(dev);
                break;
        }
        kfree(pw);
}

int pm8001_handle_event(struct pm8001_hba_info *pm8001_ha, void *data,
                               int handler)
{
        struct pm8001_work *pw;
        int ret = 0;

        pw = kmalloc(sizeof(struct pm8001_work), GFP_ATOMIC);
        if (pw) {
                pw->pm8001_ha = pm8001_ha;
                pw->data = data;
                pw->handler = handler;
                INIT_WORK(&pw->work, pm8001_work_fn);
                queue_work(pm8001_wq, &pw->work);
        } else
                ret = -ENOMEM;

        return ret;
}

static void pm8001_send_abort_all(struct pm8001_hba_info *pm8001_ha,
                struct pm8001_device *pm8001_ha_dev)
{
        int res;
        u32 ccb_tag;
        struct pm8001_ccb_info *ccb;
        struct sas_task *task = NULL;
        struct task_abort_req task_abort;
        struct inbound_queue_table *circularQ;
        u32 opc = OPC_INB_SATA_ABORT;
        int ret;

        if (!pm8001_ha_dev) {
                PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("dev is null\n"));
                return;
        }

        task = sas_alloc_slow_task(GFP_ATOMIC);

        if (!task) {
                PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("cannot "
                                                "allocate task\n"));
                return;
        }

        task->task_done = pm8001_task_done;

        res = pm8001_tag_alloc(pm8001_ha, &ccb_tag);
        if (res)
                return;

        ccb = &pm8001_ha->ccb_info[ccb_tag];
        ccb->device = pm8001_ha_dev;
        ccb->ccb_tag = ccb_tag;
        ccb->task = task;

        circularQ = &pm8001_ha->inbnd_q_tbl[0];

        memset(&task_abort, 0, sizeof(task_abort));
        task_abort.abort_all = cpu_to_le32(1);
        task_abort.device_id = cpu_to_le32(pm8001_ha_dev->device_id);
        task_abort.tag = cpu_to_le32(ccb_tag);

        ret = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &task_abort, 0);
        if (ret)
                pm8001_tag_free(pm8001_ha, ccb_tag);

}

static void pm8001_send_read_log(struct pm8001_hba_info *pm8001_ha,
                struct pm8001_device *pm8001_ha_dev)
{
        struct sata_start_req sata_cmd;
        int res;
        u32 ccb_tag;
        struct pm8001_ccb_info *ccb;
        struct sas_task *task = NULL;
        struct host_to_dev_fis fis;
        struct domain_device *dev;
        struct inbound_queue_table *circularQ;
        u32 opc = OPC_INB_SATA_HOST_OPSTART;

        task = sas_alloc_slow_task(GFP_ATOMIC);

        if (!task) {
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("cannot allocate task !!!\n"));
                return;
        }
        task->task_done = pm8001_task_done;

        res = pm8001_tag_alloc(pm8001_ha, &ccb_tag);
        if (res) {
                sas_free_task(task);
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("cannot allocate tag !!!\n"));
                return;
        }

        /* allocate domain device by ourselves as libsas
         * is not going to provide any
        */
        dev = kzalloc(sizeof(struct domain_device), GFP_ATOMIC);
        if (!dev) {
                sas_free_task(task);
                pm8001_tag_free(pm8001_ha, ccb_tag);
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("Domain device cannot be allocated\n"));
                return;
        }
        task->dev = dev;
        task->dev->lldd_dev = pm8001_ha_dev;

        ccb = &pm8001_ha->ccb_info[ccb_tag];
        ccb->device = pm8001_ha_dev;
        ccb->ccb_tag = ccb_tag;
        ccb->task = task;
        pm8001_ha_dev->id |= NCQ_READ_LOG_FLAG;
        pm8001_ha_dev->id |= NCQ_2ND_RLE_FLAG;

        memset(&sata_cmd, 0, sizeof(sata_cmd));
        circularQ = &pm8001_ha->inbnd_q_tbl[0];

        /* construct read log FIS */
        memset(&fis, 0, sizeof(struct host_to_dev_fis));
        fis.fis_type = 0x27;
        fis.flags = 0x80;
        fis.command = ATA_CMD_READ_LOG_EXT;
        fis.lbal = 0x10;
        fis.sector_count = 0x1;

        sata_cmd.tag = cpu_to_le32(ccb_tag);
        sata_cmd.device_id = cpu_to_le32(pm8001_ha_dev->device_id);
        sata_cmd.ncqtag_atap_dir_m |= ((0x1 << 7) | (0x5 << 9));
        memcpy(&sata_cmd.sata_fis, &fis, sizeof(struct host_to_dev_fis));

        res = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &sata_cmd, 0);
        if (res) {
                sas_free_task(task);
                pm8001_tag_free(pm8001_ha, ccb_tag);
                kfree(dev);
        }
}

/**
 * mpi_ssp_completion- process the event that FW response to the SSP request.
 * @pm8001_ha: our hba card information
 * @piomb: the message contents of this outbound message.
 *
 * When FW has completed a ssp request for example a IO request, after it has
 * filled the SG data with the data, it will trigger this event represent
 * that he has finished the job,please check the coresponding buffer.
 * So we will tell the caller who maybe waiting the result to tell upper layer
 * that the task has been finished.
 */
static void
mpi_ssp_completion(struct pm8001_hba_info *pm8001_ha , void *piomb)
{
        struct sas_task *t;
        struct pm8001_ccb_info *ccb;
        unsigned long flags;
        u32 status;
        u32 param;
        u32 tag;
        struct ssp_completion_resp *psspPayload;
        struct task_status_struct *ts;
        struct ssp_response_iu *iu;
        struct pm8001_device *pm8001_dev;
        psspPayload = (struct ssp_completion_resp *)(piomb + 4);
        status = le32_to_cpu(psspPayload->status);
        tag = le32_to_cpu(psspPayload->tag);
        ccb = &pm8001_ha->ccb_info[tag];
        if ((status == IO_ABORTED) && ccb->open_retry) {
                /* Being completed by another */
                ccb->open_retry = 0;
                return;
        }
        pm8001_dev = ccb->device;
        param = le32_to_cpu(psspPayload->param);

        t = ccb->task;

        if (status && status != IO_UNDERFLOW)
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("sas IO status 0x%x\n", status));
        if (unlikely(!t || !t->lldd_task || !t->dev))
                return;
        ts = &t->task_status;
        /* Print sas address of IO failed device */
        if ((status != IO_SUCCESS) && (status != IO_OVERFLOW) &&
                (status != IO_UNDERFLOW))
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("SAS Address of IO Failure Drive:"
                        "%016llx", SAS_ADDR(t->dev->sas_addr)));

        switch (status) {
        case IO_SUCCESS:
                PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_SUCCESS"
                        ",param = %d\n", param));
                if (param == 0) {
                        ts->resp = SAS_TASK_COMPLETE;
                        ts->stat = SAM_STAT_GOOD;
                } else {
                        ts->resp = SAS_TASK_COMPLETE;
                        ts->stat = SAS_PROTO_RESPONSE;
                        ts->residual = param;
                        iu = &psspPayload->ssp_resp_iu;
                        sas_ssp_task_response(pm8001_ha->dev, t, iu);
                }
                if (pm8001_dev)
                        pm8001_dev->running_req--;
                break;
        case IO_ABORTED:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_ABORTED IOMB Tag\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_ABORTED_TASK;
                break;
        case IO_UNDERFLOW:
                /* SSP Completion with error */
                PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_UNDERFLOW"
                        ",param = %d\n", param));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_DATA_UNDERRUN;
                ts->residual = param;
                if (pm8001_dev)
                        pm8001_dev->running_req--;
                break;
        case IO_NO_DEVICE:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_NO_DEVICE\n"));
                ts->resp = SAS_TASK_UNDELIVERED;
                ts->stat = SAS_PHY_DOWN;
                break;
        case IO_XFER_ERROR_BREAK:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_BREAK\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                /* Force the midlayer to retry */
                ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
                break;
        case IO_XFER_ERROR_PHY_NOT_READY:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
                break;
        case IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED:
                PM8001_IO_DBG(pm8001_ha,
                pm8001_printk("IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_EPROTO;
                break;
        case IO_OPEN_CNX_ERROR_ZONE_VIOLATION:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_UNKNOWN;
                break;
        case IO_OPEN_CNX_ERROR_BREAK:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
                break;
        case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_UNKNOWN;
                if (!t->uldd_task)
                        pm8001_handle_event(pm8001_ha,
                                pm8001_dev,
                                IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
                break;
        case IO_OPEN_CNX_ERROR_BAD_DESTINATION:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_BAD_DEST;
                break;
        case IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_CONNECTION_RATE_"
                        "NOT_SUPPORTED\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_CONN_RATE;
                break;
        case IO_OPEN_CNX_ERROR_WRONG_DESTINATION:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n"));
                ts->resp = SAS_TASK_UNDELIVERED;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_WRONG_DEST;
                break;
        case IO_XFER_ERROR_NAK_RECEIVED:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_NAK_RECEIVED\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
                break;
        case IO_XFER_ERROR_ACK_NAK_TIMEOUT:

                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_ACK_NAK_TIMEOUT\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_NAK_R_ERR;
                break;
        case IO_XFER_ERROR_DMA:
                PM8001_IO_DBG(pm8001_ha,
                pm8001_printk("IO_XFER_ERROR_DMA\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                break;
        case IO_XFER_OPEN_RETRY_TIMEOUT:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
                break;
        case IO_XFER_ERROR_OFFSET_MISMATCH:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_OFFSET_MISMATCH\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                break;
        case IO_PORT_IN_RESET:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_PORT_IN_RESET\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                break;
        case IO_DS_NON_OPERATIONAL:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_DS_NON_OPERATIONAL\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                if (!t->uldd_task)
                        pm8001_handle_event(pm8001_ha,
                                pm8001_dev,
                                IO_DS_NON_OPERATIONAL);
                break;
        case IO_DS_IN_RECOVERY:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_DS_IN_RECOVERY\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                break;
        case IO_TM_TAG_NOT_FOUND:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_TM_TAG_NOT_FOUND\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                break;
        case IO_SSP_EXT_IU_ZERO_LEN_ERROR:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_SSP_EXT_IU_ZERO_LEN_ERROR\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                break;
        case IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
                break;
        default:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("Unknown status 0x%x\n", status));
                /* not allowed case. Therefore, return failed status */
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                break;
        }
        PM8001_IO_DBG(pm8001_ha,
                pm8001_printk("scsi_status = %x\n ",
                psspPayload->ssp_resp_iu.status));
        spin_lock_irqsave(&t->task_state_lock, flags);
        t->task_state_flags &= ~SAS_TASK_STATE_PENDING;
        t->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
        t->task_state_flags |= SAS_TASK_STATE_DONE;
        if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) {
                spin_unlock_irqrestore(&t->task_state_lock, flags);
                PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("task 0x%p done with"
                        " io_status 0x%x resp 0x%x "
                        "stat 0x%x but aborted by upper layer!\n",
                        t, status, ts->resp, ts->stat));
                pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
        } else {
                spin_unlock_irqrestore(&t->task_state_lock, flags);
                pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
                mb();/* in order to force CPU ordering */
                t->task_done(t);
        }
}

/*See the comments for mpi_ssp_completion */
static void mpi_ssp_event(struct pm8001_hba_info *pm8001_ha , void *piomb)
{
        struct sas_task *t;
        unsigned long flags;
        struct task_status_struct *ts;
        struct pm8001_ccb_info *ccb;
        struct pm8001_device *pm8001_dev;
        struct ssp_event_resp *psspPayload =
                (struct ssp_event_resp *)(piomb + 4);
        u32 event = le32_to_cpu(psspPayload->event);
        u32 tag = le32_to_cpu(psspPayload->tag);
        u32 port_id = le32_to_cpu(psspPayload->port_id);
        u32 dev_id = le32_to_cpu(psspPayload->device_id);

        ccb = &pm8001_ha->ccb_info[tag];
        t = ccb->task;
        pm8001_dev = ccb->device;
        if (event)
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("sas IO status 0x%x\n", event));
        if (unlikely(!t || !t->lldd_task || !t->dev))
                return;
        ts = &t->task_status;
        PM8001_IO_DBG(pm8001_ha,
                pm8001_printk("port_id = %x,device_id = %x\n",
                port_id, dev_id));
        switch (event) {
        case IO_OVERFLOW:
                PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_UNDERFLOW\n");)
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_DATA_OVERRUN;
                ts->residual = 0;
                if (pm8001_dev)
                        pm8001_dev->running_req--;
                break;
        case IO_XFER_ERROR_BREAK:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_BREAK\n"));
                pm8001_handle_event(pm8001_ha, t, IO_XFER_ERROR_BREAK);
                return;
        case IO_XFER_ERROR_PHY_NOT_READY:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
                break;
        case IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_PROTOCOL_NOT"
                        "_SUPPORTED\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_EPROTO;
                break;
        case IO_OPEN_CNX_ERROR_ZONE_VIOLATION:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_UNKNOWN;
                break;
        case IO_OPEN_CNX_ERROR_BREAK:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
                break;
        case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_UNKNOWN;
                if (!t->uldd_task)
                        pm8001_handle_event(pm8001_ha,
                                pm8001_dev,
                                IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
                break;
        case IO_OPEN_CNX_ERROR_BAD_DESTINATION:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_BAD_DEST;
                break;
        case IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_CONNECTION_RATE_"
                        "NOT_SUPPORTED\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_CONN_RATE;
                break;
        case IO_OPEN_CNX_ERROR_WRONG_DESTINATION:
                PM8001_IO_DBG(pm8001_ha,
                       pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_WRONG_DEST;
                break;
        case IO_XFER_ERROR_NAK_RECEIVED:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_NAK_RECEIVED\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
                break;
        case IO_XFER_ERROR_ACK_NAK_TIMEOUT:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_ACK_NAK_TIMEOUT\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_NAK_R_ERR;
                break;
        case IO_XFER_OPEN_RETRY_TIMEOUT:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n"));
                pm8001_handle_event(pm8001_ha, t, IO_XFER_OPEN_RETRY_TIMEOUT);
                return;
        case IO_XFER_ERROR_UNEXPECTED_PHASE:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_UNEXPECTED_PHASE\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_DATA_OVERRUN;
                break;
        case IO_XFER_ERROR_XFER_RDY_OVERRUN:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_XFER_RDY_OVERRUN\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_DATA_OVERRUN;
                break;
        case IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED:
                PM8001_IO_DBG(pm8001_ha,
                       pm8001_printk("IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_DATA_OVERRUN;
                break;
        case IO_XFER_ERROR_CMD_ISSUE_ACK_NAK_TIMEOUT:
                PM8001_IO_DBG(pm8001_ha,
                pm8001_printk("IO_XFER_ERROR_CMD_ISSUE_ACK_NAK_TIMEOUT\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_DATA_OVERRUN;
                break;
        case IO_XFER_ERROR_OFFSET_MISMATCH:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_OFFSET_MISMATCH\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_DATA_OVERRUN;
                break;
        case IO_XFER_ERROR_XFER_ZERO_DATA_LEN:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_XFER_ZERO_DATA_LEN\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_DATA_OVERRUN;
                break;
        case IO_XFER_CMD_FRAME_ISSUED:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("  IO_XFER_CMD_FRAME_ISSUED\n"));
                return;
        default:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("Unknown status 0x%x\n", event));
                /* not allowed case. Therefore, return failed status */
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_DATA_OVERRUN;
                break;
        }
        spin_lock_irqsave(&t->task_state_lock, flags);
        t->task_state_flags &= ~SAS_TASK_STATE_PENDING;
        t->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
        t->task_state_flags |= SAS_TASK_STATE_DONE;
        if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) {
                spin_unlock_irqrestore(&t->task_state_lock, flags);
                PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("task 0x%p done with"
                        " event 0x%x resp 0x%x "
                        "stat 0x%x but aborted by upper layer!\n",
                        t, event, ts->resp, ts->stat));
                pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
        } else {
                spin_unlock_irqrestore(&t->task_state_lock, flags);
                pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
                mb();/* in order to force CPU ordering */
                t->task_done(t);
        }
}

/*See the comments for mpi_ssp_completion */
static void
mpi_sata_completion(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
        struct sas_task *t;
        struct pm8001_ccb_info *ccb;
        u32 param;
        u32 status;
        u32 tag;
        int i, j;
        u8 sata_addr_low[4];
        u32 temp_sata_addr_low;
        u8 sata_addr_hi[4];
        u32 temp_sata_addr_hi;
        struct sata_completion_resp *psataPayload;
        struct task_status_struct *ts;
        struct ata_task_resp *resp ;
        u32 *sata_resp;
        struct pm8001_device *pm8001_dev;
        unsigned long flags;

        psataPayload = (struct sata_completion_resp *)(piomb + 4);
        status = le32_to_cpu(psataPayload->status);
        tag = le32_to_cpu(psataPayload->tag);

        if (!tag) {
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("tag null\n"));
                return;
        }
        ccb = &pm8001_ha->ccb_info[tag];
        param = le32_to_cpu(psataPayload->param);
        if (ccb) {
                t = ccb->task;
                pm8001_dev = ccb->device;
        } else {
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("ccb null\n"));
                return;
        }

        if (t) {
                if (t->dev && (t->dev->lldd_dev))
                        pm8001_dev = t->dev->lldd_dev;
        } else {
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("task null\n"));
                return;
        }

        if ((pm8001_dev && !(pm8001_dev->id & NCQ_READ_LOG_FLAG))
                && unlikely(!t || !t->lldd_task || !t->dev)) {
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("task or dev null\n"));
                return;
        }

        ts = &t->task_status;
        if (!ts) {
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("ts null\n"));
                return;
        }
        /* Print sas address of IO failed device */
        if ((status != IO_SUCCESS) && (status != IO_OVERFLOW) &&
                (status != IO_UNDERFLOW)) {
                if (!((t->dev->parent) &&
                        (DEV_IS_EXPANDER(t->dev->parent->dev_type)))) {
                        for (i = 0 , j = 4; j <= 7 && i <= 3; i++ , j++)
                                sata_addr_low[i] = pm8001_ha->sas_addr[j];
                        for (i = 0 , j = 0; j <= 3 && i <= 3; i++ , j++)
                                sata_addr_hi[i] = pm8001_ha->sas_addr[j];
                        memcpy(&temp_sata_addr_low, sata_addr_low,
                                sizeof(sata_addr_low));
                        memcpy(&temp_sata_addr_hi, sata_addr_hi,
                                sizeof(sata_addr_hi));
                        temp_sata_addr_hi = (((temp_sata_addr_hi >> 24) & 0xff)
                                                |((temp_sata_addr_hi << 8) &
                                                0xff0000) |
                                                ((temp_sata_addr_hi >> 8)
                                                & 0xff00) |
                                                ((temp_sata_addr_hi << 24) &
                                                0xff000000));
                        temp_sata_addr_low = ((((temp_sata_addr_low >> 24)
                                                & 0xff) |
                                                ((temp_sata_addr_low << 8)
                                                & 0xff0000) |
                                                ((temp_sata_addr_low >> 8)
                                                & 0xff00) |
                                                ((temp_sata_addr_low << 24)
                                                & 0xff000000)) +
                                                pm8001_dev->attached_phy +
                                                0x10);
                        PM8001_FAIL_DBG(pm8001_ha,
                                pm8001_printk("SAS Address of IO Failure Drive:"
                                "%08x%08x", temp_sata_addr_hi,
                                        temp_sata_addr_low));
                } else {
                        PM8001_FAIL_DBG(pm8001_ha,
                                pm8001_printk("SAS Address of IO Failure Drive:"
                                "%016llx", SAS_ADDR(t->dev->sas_addr)));
                }
        }
        switch (status) {
        case IO_SUCCESS:
                PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_SUCCESS\n"));
                if (param == 0) {
                        ts->resp = SAS_TASK_COMPLETE;
                        ts->stat = SAM_STAT_GOOD;
                        /* check if response is for SEND READ LOG */
                        if (pm8001_dev &&
                                (pm8001_dev->id & NCQ_READ_LOG_FLAG)) {
                                /* set new bit for abort_all */
                                pm8001_dev->id |= NCQ_ABORT_ALL_FLAG;
                                /* clear bit for read log */
                                pm8001_dev->id = pm8001_dev->id & 0x7FFFFFFF;
                                pm8001_send_abort_all(pm8001_ha, pm8001_dev);
                                /* Free the tag */
                                pm8001_tag_free(pm8001_ha, tag);
                                sas_free_task(t);
                                return;
                        }
                } else {
                        u8 len;
                        ts->resp = SAS_TASK_COMPLETE;
                        ts->stat = SAS_PROTO_RESPONSE;
                        ts->residual = param;
                        PM8001_IO_DBG(pm8001_ha,
                                pm8001_printk("SAS_PROTO_RESPONSE len = %d\n",
                                param));
                        sata_resp = &psataPayload->sata_resp[0];
                        resp = (struct ata_task_resp *)ts->buf;
                        if (t->ata_task.dma_xfer == 0 &&
                        t->data_dir == PCI_DMA_FROMDEVICE) {
                                len = sizeof(struct pio_setup_fis);
                                PM8001_IO_DBG(pm8001_ha,
                                pm8001_printk("PIO read len = %d\n", len));
                        } else if (t->ata_task.use_ncq) {
                                len = sizeof(struct set_dev_bits_fis);
                                PM8001_IO_DBG(pm8001_ha,
                                        pm8001_printk("FPDMA len = %d\n", len));
                        } else {
                                len = sizeof(struct dev_to_host_fis);
                                PM8001_IO_DBG(pm8001_ha,
                                pm8001_printk("other len = %d\n", len));
                        }
                        if (SAS_STATUS_BUF_SIZE >= sizeof(*resp)) {
                                resp->frame_len = len;
                                memcpy(&resp->ending_fis[0], sata_resp, len);
                                ts->buf_valid_size = sizeof(*resp);
                        } else
                                PM8001_IO_DBG(pm8001_ha,
                                        pm8001_printk("response to large\n"));
                }
                if (pm8001_dev)
                        pm8001_dev->running_req--;
                break;
        case IO_ABORTED:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_ABORTED IOMB Tag\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_ABORTED_TASK;
                if (pm8001_dev)
                        pm8001_dev->running_req--;
                break;
                /* following cases are to do cases */
        case IO_UNDERFLOW:
                /* SATA Completion with error */
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_UNDERFLOW param = %d\n", param));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_DATA_UNDERRUN;
                ts->residual =  param;
                if (pm8001_dev)
                        pm8001_dev->running_req--;
                break;
        case IO_NO_DEVICE:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_NO_DEVICE\n"));
                ts->resp = SAS_TASK_UNDELIVERED;
                ts->stat = SAS_PHY_DOWN;
                break;
        case IO_XFER_ERROR_BREAK:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_BREAK\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_INTERRUPTED;
                break;
        case IO_XFER_ERROR_PHY_NOT_READY:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
                break;
        case IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_PROTOCOL_NOT"
                        "_SUPPORTED\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_EPROTO;
                break;
        case IO_OPEN_CNX_ERROR_ZONE_VIOLATION:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_UNKNOWN;
                break;
        case IO_OPEN_CNX_ERROR_BREAK:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_RSVD_CONT0;
                break;
        case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_DEV_NO_RESPONSE;
                if (!t->uldd_task) {
                        pm8001_handle_event(pm8001_ha,
                                pm8001_dev,
                                IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
                        ts->resp = SAS_TASK_UNDELIVERED;
                        ts->stat = SAS_QUEUE_FULL;
                        pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
                        return;
                }
                break;
        case IO_OPEN_CNX_ERROR_BAD_DESTINATION:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n"));
                ts->resp = SAS_TASK_UNDELIVERED;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_BAD_DEST;
                if (!t->uldd_task) {
                        pm8001_handle_event(pm8001_ha,
                                pm8001_dev,
                                IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
                        ts->resp = SAS_TASK_UNDELIVERED;
                        ts->stat = SAS_QUEUE_FULL;
                        pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
                        return;
                }
                break;
        case IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_CONNECTION_RATE_"
                        "NOT_SUPPORTED\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_CONN_RATE;
                break;
        case IO_OPEN_CNX_ERROR_STP_RESOURCES_BUSY:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_STP_RESOURCES"
                        "_BUSY\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_DEV_NO_RESPONSE;
                if (!t->uldd_task) {
                        pm8001_handle_event(pm8001_ha,
                                pm8001_dev,
                                IO_OPEN_CNX_ERROR_STP_RESOURCES_BUSY);
                        ts->resp = SAS_TASK_UNDELIVERED;
                        ts->stat = SAS_QUEUE_FULL;
                        pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
                        return;
                }
                break;
        case IO_OPEN_CNX_ERROR_WRONG_DESTINATION:
                PM8001_IO_DBG(pm8001_ha,
                       pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_WRONG_DEST;
                break;
        case IO_XFER_ERROR_NAK_RECEIVED:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_NAK_RECEIVED\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_NAK_R_ERR;
                break;
        case IO_XFER_ERROR_ACK_NAK_TIMEOUT:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_ACK_NAK_TIMEOUT\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_NAK_R_ERR;
                break;
        case IO_XFER_ERROR_DMA:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_DMA\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_ABORTED_TASK;
                break;
        case IO_XFER_ERROR_SATA_LINK_TIMEOUT:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_SATA_LINK_TIMEOUT\n"));
                ts->resp = SAS_TASK_UNDELIVERED;
                ts->stat = SAS_DEV_NO_RESPONSE;
                break;
        case IO_XFER_ERROR_REJECTED_NCQ_MODE:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_REJECTED_NCQ_MODE\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_DATA_UNDERRUN;
                break;
        case IO_XFER_OPEN_RETRY_TIMEOUT:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_TO;
                break;
        case IO_PORT_IN_RESET:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_PORT_IN_RESET\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_DEV_NO_RESPONSE;
                break;
        case IO_DS_NON_OPERATIONAL:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_DS_NON_OPERATIONAL\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_DEV_NO_RESPONSE;
                if (!t->uldd_task) {
                        pm8001_handle_event(pm8001_ha, pm8001_dev,
                                    IO_DS_NON_OPERATIONAL);
                        ts->resp = SAS_TASK_UNDELIVERED;
                        ts->stat = SAS_QUEUE_FULL;
                        pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
                        return;
                }
                break;
        case IO_DS_IN_RECOVERY:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("  IO_DS_IN_RECOVERY\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_DEV_NO_RESPONSE;
                break;
        case IO_DS_IN_ERROR:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_DS_IN_ERROR\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_DEV_NO_RESPONSE;
                if (!t->uldd_task) {
                        pm8001_handle_event(pm8001_ha, pm8001_dev,
                                    IO_DS_IN_ERROR);
                        ts->resp = SAS_TASK_UNDELIVERED;
                        ts->stat = SAS_QUEUE_FULL;
                        pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
                        return;
                }
                break;
        case IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
                break;
        default:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("Unknown status 0x%x\n", status));
                /* not allowed case. Therefore, return failed status */
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_DEV_NO_RESPONSE;
                break;
        }
        spin_lock_irqsave(&t->task_state_lock, flags);
        t->task_state_flags &= ~SAS_TASK_STATE_PENDING;
        t->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
        t->task_state_flags |= SAS_TASK_STATE_DONE;
        if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) {
                spin_unlock_irqrestore(&t->task_state_lock, flags);
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("task 0x%p done with io_status 0x%x"
                        " resp 0x%x stat 0x%x but aborted by upper layer!\n",
                        t, status, ts->resp, ts->stat));
                pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
        } else {
                spin_unlock_irqrestore(&t->task_state_lock, flags);
                pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
        }
}

/*See the comments for mpi_ssp_completion */
static void mpi_sata_event(struct pm8001_hba_info *pm8001_ha , void *piomb)
{
        struct sas_task *t;
        struct task_status_struct *ts;
        struct pm8001_ccb_info *ccb;
        struct pm8001_device *pm8001_dev;
        struct sata_event_resp *psataPayload =
                (struct sata_event_resp *)(piomb + 4);
        u32 event = le32_to_cpu(psataPayload->event);
        u32 tag = le32_to_cpu(psataPayload->tag);
        u32 port_id = le32_to_cpu(psataPayload->port_id);
        u32 dev_id = le32_to_cpu(psataPayload->device_id);
        unsigned long flags;

        ccb = &pm8001_ha->ccb_info[tag];

        if (ccb) {
                t = ccb->task;
                pm8001_dev = ccb->device;
        } else {
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("No CCB !!!. returning\n"));
        }
        if (event)
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("SATA EVENT 0x%x\n", event));

        /* Check if this is NCQ error */
        if (event == IO_XFER_ERROR_ABORTED_NCQ_MODE) {
                /* find device using device id */
                pm8001_dev = pm8001_find_dev(pm8001_ha, dev_id);
                /* send read log extension */
                if (pm8001_dev)
                        pm8001_send_read_log(pm8001_ha, pm8001_dev);
                return;
        }

        ccb = &pm8001_ha->ccb_info[tag];
        t = ccb->task;
        pm8001_dev = ccb->device;
        if (event)
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("sata IO status 0x%x\n", event));
        if (unlikely(!t || !t->lldd_task || !t->dev))
                return;
        ts = &t->task_status;
        PM8001_IO_DBG(pm8001_ha, pm8001_printk(
                "port_id:0x%x, device_id:0x%x, tag:0x%x, event:0x%x\n",
                port_id, dev_id, tag, event));
        switch (event) {
        case IO_OVERFLOW:
                PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_UNDERFLOW\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_DATA_OVERRUN;
                ts->residual = 0;
                if (pm8001_dev)
                        pm8001_dev->running_req--;
                break;
        case IO_XFER_ERROR_BREAK:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_BREAK\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_INTERRUPTED;
                break;
        case IO_XFER_ERROR_PHY_NOT_READY:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
                break;
        case IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_PROTOCOL_NOT"
                        "_SUPPORTED\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_EPROTO;
                break;
        case IO_OPEN_CNX_ERROR_ZONE_VIOLATION:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_UNKNOWN;
                break;
        case IO_OPEN_CNX_ERROR_BREAK:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_RSVD_CONT0;
                break;
        case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n"));
                ts->resp = SAS_TASK_UNDELIVERED;
                ts->stat = SAS_DEV_NO_RESPONSE;
                if (!t->uldd_task) {
                        pm8001_handle_event(pm8001_ha,
                                pm8001_dev,
                                IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
                        ts->resp = SAS_TASK_COMPLETE;
                        ts->stat = SAS_QUEUE_FULL;
                        pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
                        return;
                }
                break;
        case IO_OPEN_CNX_ERROR_BAD_DESTINATION:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n"));
                ts->resp = SAS_TASK_UNDELIVERED;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_BAD_DEST;
                break;
        case IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_CONNECTION_RATE_"
                        "NOT_SUPPORTED\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_CONN_RATE;
                break;
        case IO_OPEN_CNX_ERROR_WRONG_DESTINATION:
                PM8001_IO_DBG(pm8001_ha,
                       pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_WRONG_DEST;
                break;
        case IO_XFER_ERROR_NAK_RECEIVED:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_NAK_RECEIVED\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_NAK_R_ERR;
                break;
        case IO_XFER_ERROR_PEER_ABORTED:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_PEER_ABORTED\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_NAK_R_ERR;
                break;
        case IO_XFER_ERROR_REJECTED_NCQ_MODE:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_REJECTED_NCQ_MODE\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_DATA_UNDERRUN;
                break;
        case IO_XFER_OPEN_RETRY_TIMEOUT:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_TO;
                break;
        case IO_XFER_ERROR_UNEXPECTED_PHASE:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_UNEXPECTED_PHASE\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_TO;
                break;
        case IO_XFER_ERROR_XFER_RDY_OVERRUN:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_XFER_RDY_OVERRUN\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_TO;
                break;
        case IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED:
                PM8001_IO_DBG(pm8001_ha,
                       pm8001_printk("IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_TO;
                break;
        case IO_XFER_ERROR_OFFSET_MISMATCH:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_OFFSET_MISMATCH\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_TO;
                break;
        case IO_XFER_ERROR_XFER_ZERO_DATA_LEN:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_XFER_ZERO_DATA_LEN\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_TO;
                break;
        case IO_XFER_CMD_FRAME_ISSUED:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_CMD_FRAME_ISSUED\n"));
                break;
        case IO_XFER_PIO_SETUP_ERROR:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_PIO_SETUP_ERROR\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_TO;
                break;
        default:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("Unknown status 0x%x\n", event));
                /* not allowed case. Therefore, return failed status */
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_TO;
                break;
        }
        spin_lock_irqsave(&t->task_state_lock, flags);
        t->task_state_flags &= ~SAS_TASK_STATE_PENDING;
        t->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
        t->task_state_flags |= SAS_TASK_STATE_DONE;
        if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) {
                spin_unlock_irqrestore(&t->task_state_lock, flags);
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("task 0x%p done with io_status 0x%x"
                        " resp 0x%x stat 0x%x but aborted by upper layer!\n",
                        t, event, ts->resp, ts->stat));
                pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
        } else {
                spin_unlock_irqrestore(&t->task_state_lock, flags);
                pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
        }
}

/*See the comments for mpi_ssp_completion */
static void
mpi_smp_completion(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
        u32 param;
        struct sas_task *t;
        struct pm8001_ccb_info *ccb;
        unsigned long flags;
        u32 status;
        u32 tag;
        struct smp_completion_resp *psmpPayload;
        struct task_status_struct *ts;
        struct pm8001_device *pm8001_dev;

        psmpPayload = (struct smp_completion_resp *)(piomb + 4);
        status = le32_to_cpu(psmpPayload->status);
        tag = le32_to_cpu(psmpPayload->tag);

        ccb = &pm8001_ha->ccb_info[tag];
        param = le32_to_cpu(psmpPayload->param);
        t = ccb->task;
        ts = &t->task_status;
        pm8001_dev = ccb->device;
        if (status)
                PM8001_FAIL_DBG(pm8001_ha,
                        pm8001_printk("smp IO status 0x%x\n", status));
        if (unlikely(!t || !t->lldd_task || !t->dev))
                return;

        switch (status) {
        case IO_SUCCESS:
                PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_SUCCESS\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAM_STAT_GOOD;
        if (pm8001_dev)
                        pm8001_dev->running_req--;
                break;
        case IO_ABORTED:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_ABORTED IOMB\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_ABORTED_TASK;
                if (pm8001_dev)
                        pm8001_dev->running_req--;
                break;
        case IO_OVERFLOW:
                PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_UNDERFLOW\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_DATA_OVERRUN;
                ts->residual = 0;
                if (pm8001_dev)
                        pm8001_dev->running_req--;
                break;
        case IO_NO_DEVICE:
                PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_NO_DEVICE\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_PHY_DOWN;
                break;
        case IO_ERROR_HW_TIMEOUT:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_ERROR_HW_TIMEOUT\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAM_STAT_BUSY;
                break;
        case IO_XFER_ERROR_BREAK:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_BREAK\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAM_STAT_BUSY;
                break;
        case IO_XFER_ERROR_PHY_NOT_READY:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAM_STAT_BUSY;
                break;
        case IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED:
                PM8001_IO_DBG(pm8001_ha,
                pm8001_printk("IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_UNKNOWN;
                break;
        case IO_OPEN_CNX_ERROR_ZONE_VIOLATION:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_UNKNOWN;
                break;
        case IO_OPEN_CNX_ERROR_BREAK:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_RSVD_CONT0;
                break;
        case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n"));
                ts->resp = SAS_TASK_COMPLETE;
                ts->stat = SAS_OPEN_REJECT;
                ts->open_rej_reason = SAS_OREJ_UNKNOWN;
                pm8001_handle_event(pm8001_ha,
                                pm8001_dev,
                                IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
                break;
        case IO_OPEN_CNX_ERROR_BAD_DESTINATION:
                PM8001_IO_DBG(pm8001_ha,
                        pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n"));