/*
 * wm8903.c  --  WM8903 ALSA SoC Audio driver
 *
 * Copyright 2008-12 Wolfson Microelectronics
 * Copyright 2011-2012 NVIDIA, Inc.
 *
 * Author: Mark Brown <broonie@opensource.wolfsonmicro.com>
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 *
 * TODO:
 *  - TDM mode configuration.
 *  - Digital microphone support.
 */

#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/init.h>
#include <linux/completion.h>
#include <linux/delay.h>
#include <linux/gpio/driver.h>
#include <linux/pm.h>
#include <linux/i2c.h>
#include <linux/regmap.h>
#include <linux/regulator/consumer.h>
#include <linux/slab.h>
#include <linux/irq.h>
#include <linux/mutex.h>
#include <sound/core.h>
#include <sound/jack.h>
#include <sound/pcm.h>
#include <sound/pcm_params.h>
#include <sound/tlv.h>
#include <sound/soc.h>
#include <sound/initval.h>
#include <sound/wm8903.h>
#include <trace/events/asoc.h>

#include "wm8903.h"

/* Register defaults at reset */
static const struct reg_default wm8903_reg_defaults[] = {
        { 4,  0x0018 },     /* R4   - Bias Control 0 */
        { 5,  0x0000 },     /* R5   - VMID Control 0 */
        { 6,  0x0000 },     /* R6   - Mic Bias Control 0 */
        { 8,  0x0001 },     /* R8   - Analogue DAC 0 */
        { 10, 0x0001 },     /* R10  - Analogue ADC 0 */
        { 12, 0x0000 },     /* R12  - Power Management 0 */
        { 13, 0x0000 },     /* R13  - Power Management 1 */
        { 14, 0x0000 },     /* R14  - Power Management 2 */
        { 15, 0x0000 },     /* R15  - Power Management 3 */
        { 16, 0x0000 },     /* R16  - Power Management 4 */
        { 17, 0x0000 },     /* R17  - Power Management 5 */
        { 18, 0x0000 },     /* R18  - Power Management 6 */
        { 20, 0x0400 },     /* R20  - Clock Rates 0 */
        { 21, 0x0D07 },     /* R21  - Clock Rates 1 */
        { 22, 0x0000 },     /* R22  - Clock Rates 2 */
        { 24, 0x0050 },     /* R24  - Audio Interface 0 */
        { 25, 0x0242 },     /* R25  - Audio Interface 1 */
        { 26, 0x0008 },     /* R26  - Audio Interface 2 */
        { 27, 0x0022 },     /* R27  - Audio Interface 3 */
        { 30, 0x00C0 },     /* R30  - DAC Digital Volume Left */
        { 31, 0x00C0 },     /* R31  - DAC Digital Volume Right */
        { 32, 0x0000 },     /* R32  - DAC Digital 0 */
        { 33, 0x0000 },     /* R33  - DAC Digital 1 */
        { 36, 0x00C0 },     /* R36  - ADC Digital Volume Left */
        { 37, 0x00C0 },     /* R37  - ADC Digital Volume Right */
        { 38, 0x0000 },     /* R38  - ADC Digital 0 */
        { 39, 0x0073 },     /* R39  - Digital Microphone 0 */
        { 40, 0x09BF },     /* R40  - DRC 0 */
        { 41, 0x3241 },     /* R41  - DRC 1 */
        { 42, 0x0020 },     /* R42  - DRC 2 */
        { 43, 0x0000 },     /* R43  - DRC 3 */
        { 44, 0x0085 },     /* R44  - Analogue Left Input 0 */
        { 45, 0x0085 },     /* R45  - Analogue Right Input 0 */
        { 46, 0x0044 },     /* R46  - Analogue Left Input 1 */
        { 47, 0x0044 },     /* R47  - Analogue Right Input 1 */
        { 50, 0x0008 },     /* R50  - Analogue Left Mix 0 */
        { 51, 0x0004 },     /* R51  - Analogue Right Mix 0 */
        { 52, 0x0000 },     /* R52  - Analogue Spk Mix Left 0 */
        { 53, 0x0000 },     /* R53  - Analogue Spk Mix Left 1 */
        { 54, 0x0000 },     /* R54  - Analogue Spk Mix Right 0 */
        { 55, 0x0000 },     /* R55  - Analogue Spk Mix Right 1 */
        { 57, 0x002D },     /* R57  - Analogue OUT1 Left */
        { 58, 0x002D },     /* R58  - Analogue OUT1 Right */
        { 59, 0x0039 },     /* R59  - Analogue OUT2 Left */
        { 60, 0x0039 },     /* R60  - Analogue OUT2 Right */
        { 62, 0x0139 },     /* R62  - Analogue OUT3 Left */
        { 63, 0x0139 },     /* R63  - Analogue OUT3 Right */
        { 64, 0x0000 },     /* R65  - Analogue SPK Output Control 0 */
        { 67, 0x0010 },     /* R67  - DC Servo 0 */
        { 69, 0x00A4 },     /* R69  - DC Servo 2 */
        { 90, 0x0000 },     /* R90  - Analogue HP 0 */
        { 94, 0x0000 },     /* R94  - Analogue Lineout 0 */
        { 98, 0x0000 },     /* R98  - Charge Pump 0 */
        { 104, 0x0000 },    /* R104 - Class W 0 */
        { 108, 0x0000 },    /* R108 - Write Sequencer 0 */
        { 109, 0x0000 },    /* R109 - Write Sequencer 1 */
        { 110, 0x0000 },    /* R110 - Write Sequencer 2 */
        { 111, 0x0000 },    /* R111 - Write Sequencer 3 */
        { 112, 0x0000 },    /* R112 - Write Sequencer 4 */
        { 114, 0x0000 },    /* R114 - Control Interface */
        { 116, 0x00A8 },    /* R116 - GPIO Control 1 */
        { 117, 0x00A8 },    /* R117 - GPIO Control 2 */
        { 118, 0x00A8 },    /* R118 - GPIO Control 3 */
        { 119, 0x0220 },    /* R119 - GPIO Control 4 */
        { 120, 0x01A0 },    /* R120 - GPIO Control 5 */
        { 122, 0xFFFF },    /* R122 - Interrupt Status 1 Mask */
        { 123, 0x0000 },    /* R123 - Interrupt Polarity 1 */
        { 126, 0x0000 },    /* R126 - Interrupt Control */
        { 129, 0x0000 },    /* R129 - Control Interface Test 1 */
        { 149, 0x6810 },    /* R149 - Charge Pump Test 1 */
        { 164, 0x0028 },    /* R164 - Clock Rate Test 4 */
        { 172, 0x0000 },    /* R172 - Analogue Output Bias 0 */
};

#define WM8903_NUM_SUPPLIES 4
static const char *wm8903_supply_names[WM8903_NUM_SUPPLIES] = {
        "AVDD",
        "CPVDD",
        "DBVDD",
        "DCVDD",
};

struct wm8903_priv {
        struct wm8903_platform_data *pdata;
        struct device *dev;
        struct regmap *regmap;
        struct regulator_bulk_data supplies[WM8903_NUM_SUPPLIES];

        int sysclk;
        int irq;

        struct mutex lock;
        int fs;
        int deemph;

        int dcs_pending;
        int dcs_cache[4];

        /* Reference count */
        int class_w_users;

        struct snd_soc_jack *mic_jack;
        int mic_det;
        int mic_short;
        int mic_last_report;
        int mic_delay;

#ifdef CONFIG_GPIOLIB
        struct gpio_chip gpio_chip;
#endif
};

static bool wm8903_readable_register(struct device *dev, unsigned int reg)
{
        switch (reg) {
        case WM8903_SW_RESET_AND_ID:
        case WM8903_REVISION_NUMBER:
        case WM8903_BIAS_CONTROL_0:
        case WM8903_VMID_CONTROL_0:
        case WM8903_MIC_BIAS_CONTROL_0:
        case WM8903_ANALOGUE_DAC_0:
        case WM8903_ANALOGUE_ADC_0:
        case WM8903_POWER_MANAGEMENT_0:
        case WM8903_POWER_MANAGEMENT_1:
        case WM8903_POWER_MANAGEMENT_2:
        case WM8903_POWER_MANAGEMENT_3:
        case WM8903_POWER_MANAGEMENT_4:
        case WM8903_POWER_MANAGEMENT_5:
        case WM8903_POWER_MANAGEMENT_6:
        case WM8903_CLOCK_RATES_0:
        case WM8903_CLOCK_RATES_1:
        case WM8903_CLOCK_RATES_2:
        case WM8903_AUDIO_INTERFACE_0:
        case WM8903_AUDIO_INTERFACE_1:
        case WM8903_AUDIO_INTERFACE_2:
        case WM8903_AUDIO_INTERFACE_3:
        case WM8903_DAC_DIGITAL_VOLUME_LEFT:
        case WM8903_DAC_DIGITAL_VOLUME_RIGHT:
        case WM8903_DAC_DIGITAL_0:
        case WM8903_DAC_DIGITAL_1:
        case WM8903_ADC_DIGITAL_VOLUME_LEFT:
        case WM8903_ADC_DIGITAL_VOLUME_RIGHT:
        case WM8903_ADC_DIGITAL_0:
        case WM8903_DIGITAL_MICROPHONE_0:
        case WM8903_DRC_0:
        case WM8903_DRC_1:
        case WM8903_DRC_2:
        case WM8903_DRC_3:
        case WM8903_ANALOGUE_LEFT_INPUT_0:
        case WM8903_ANALOGUE_RIGHT_INPUT_0:
        case WM8903_ANALOGUE_LEFT_INPUT_1:
        case WM8903_ANALOGUE_RIGHT_INPUT_1:
        case WM8903_ANALOGUE_LEFT_MIX_0:
        case WM8903_ANALOGUE_RIGHT_MIX_0:
        case WM8903_ANALOGUE_SPK_MIX_LEFT_0:
        case WM8903_ANALOGUE_SPK_MIX_LEFT_1:
        case WM8903_ANALOGUE_SPK_MIX_RIGHT_0:
        case WM8903_ANALOGUE_SPK_MIX_RIGHT_1:
        case WM8903_ANALOGUE_OUT1_LEFT:
        case WM8903_ANALOGUE_OUT1_RIGHT:
        case WM8903_ANALOGUE_OUT2_LEFT:
        case WM8903_ANALOGUE_OUT2_RIGHT:
        case WM8903_ANALOGUE_OUT3_LEFT:
        case WM8903_ANALOGUE_OUT3_RIGHT:
        case WM8903_ANALOGUE_SPK_OUTPUT_CONTROL_0:
        case WM8903_DC_SERVO_0:
        case WM8903_DC_SERVO_2:
        case WM8903_DC_SERVO_READBACK_1:
        case WM8903_DC_SERVO_READBACK_2:
        case WM8903_DC_SERVO_READBACK_3:
        case WM8903_DC_SERVO_READBACK_4:
        case WM8903_ANALOGUE_HP_0:
        case WM8903_ANALOGUE_LINEOUT_0:
        case WM8903_CHARGE_PUMP_0:
        case WM8903_CLASS_W_0:
        case WM8903_WRITE_SEQUENCER_0:
        case WM8903_WRITE_SEQUENCER_1:
        case WM8903_WRITE_SEQUENCER_2:
        case WM8903_WRITE_SEQUENCER_3:
        case WM8903_WRITE_SEQUENCER_4:
        case WM8903_CONTROL_INTERFACE:
        case WM8903_GPIO_CONTROL_1:
        case WM8903_GPIO_CONTROL_2:
        case WM8903_GPIO_CONTROL_3:
        case WM8903_GPIO_CONTROL_4:
        case WM8903_GPIO_CONTROL_5:
        case WM8903_INTERRUPT_STATUS_1:
        case WM8903_INTERRUPT_STATUS_1_MASK:
        case WM8903_INTERRUPT_POLARITY_1:
        case WM8903_INTERRUPT_CONTROL:
        case WM8903_CLOCK_RATE_TEST_4:
        case WM8903_ANALOGUE_OUTPUT_BIAS_0:
                return true;
        default:
                return false;
        }
}

static bool wm8903_volatile_register(struct device *dev, unsigned int reg)
{
        switch (reg) {
        case WM8903_SW_RESET_AND_ID:
        case WM8903_REVISION_NUMBER:
        case WM8903_INTERRUPT_STATUS_1:
        case WM8903_WRITE_SEQUENCER_4:
        case WM8903_DC_SERVO_READBACK_1:
        case WM8903_DC_SERVO_READBACK_2:
        case WM8903_DC_SERVO_READBACK_3:
        case WM8903_DC_SERVO_READBACK_4:
                return true;

        default:
                return false;
        }
}

static int wm8903_cp_event(struct snd_soc_dapm_widget *w,
                           struct snd_kcontrol *kcontrol, int event)
{
        WARN_ON(event != SND_SOC_DAPM_POST_PMU);
        mdelay(4);

        return 0;
}

static int wm8903_dcs_event(struct snd_soc_dapm_widget *w,
                            struct snd_kcontrol *kcontrol, int event)
{
        struct snd_soc_component *component = snd_soc_dapm_to_component(w->dapm);
        struct wm8903_priv *wm8903 = snd_soc_component_get_drvdata(component);

        switch (event) {
        case SND_SOC_DAPM_POST_PMU:
                wm8903->dcs_pending |= 1 << w->shift;
                break;
        case SND_SOC_DAPM_PRE_PMD:
                snd_soc_component_update_bits(component, WM8903_DC_SERVO_0,
                                    1 << w->shift, 0);
                break;
        }

        return 0;
}

#define WM8903_DCS_MODE_WRITE_STOP 0
#define WM8903_DCS_MODE_START_STOP 2

static void wm8903_seq_notifier(struct snd_soc_component *component,
                                enum snd_soc_dapm_type event, int subseq)
{
        struct wm8903_priv *wm8903 = snd_soc_component_get_drvdata(component);
        int dcs_mode = WM8903_DCS_MODE_WRITE_STOP;
        int i, val;

        /* Complete any pending DC servo starts */
        if (wm8903->dcs_pending) {
                dev_dbg(component->dev, "Starting DC servo for %x\n",
                        wm8903->dcs_pending);

                /* If we've no cached values then we need to do startup */
                for (i = 0; i < ARRAY_SIZE(wm8903->dcs_cache); i++) {
                        if (!(wm8903->dcs_pending & (1 << i)))
                                continue;

                        if (wm8903->dcs_cache[i]) {
                                dev_dbg(component->dev,
                                        "Restore DC servo %d value %x\n",
                                        3 - i, wm8903->dcs_cache[i]);

                                snd_soc_component_write(component, WM8903_DC_SERVO_4 + i,
                                              wm8903->dcs_cache[i] & 0xff);
                        } else {
                                dev_dbg(component->dev,
                                        "Calibrate DC servo %d\n", 3 - i);
                                dcs_mode = WM8903_DCS_MODE_START_STOP;
                        }
                }

                /* Don't trust the cache for analogue */
                if (wm8903->class_w_users)
                        dcs_mode = WM8903_DCS_MODE_START_STOP;

                snd_soc_component_update_bits(component, WM8903_DC_SERVO_2,
                                    WM8903_DCS_MODE_MASK, dcs_mode);

                snd_soc_component_update_bits(component, WM8903_DC_SERVO_0,
                                    WM8903_DCS_ENA_MASK, wm8903->dcs_pending);

                switch (dcs_mode) {
                case WM8903_DCS_MODE_WRITE_STOP:
                        break;

                case WM8903_DCS_MODE_START_STOP:
                        msleep(270);

                        /* Cache the measured offsets for digital */
                        if (wm8903->class_w_users)
                                break;

                        for (i = 0; i < ARRAY_SIZE(wm8903->dcs_cache); i++) {
                                if (!(wm8903->dcs_pending & (1 << i)))
                                        continue;

                                val = snd_soc_component_read32(component,
                                                   WM8903_DC_SERVO_READBACK_1 + i);
                                dev_dbg(component->dev, "DC servo %d: %x\n",
                                        3 - i, val);
                                wm8903->dcs_cache[i] = val;
                        }
                        break;

                default:
                        pr_warn("DCS mode %d delay not set\n", dcs_mode);
                        break;
                }

                wm8903->dcs_pending = 0;
        }
}

/*
 * When used with DAC outputs only the WM8903 charge pump supports
 * operation in class W mode, providing very low power consumption
 * when used with digital sources.  Enable and disable this mode
 * automatically depending on the mixer configuration.
 *
 * All the relevant controls are simple switches.
 */
static int wm8903_class_w_put(struct snd_kcontrol *kcontrol,
                              struct snd_ctl_elem_value *ucontrol)
{
        struct snd_soc_component *component = snd_soc_dapm_kcontrol_component(kcontrol);
        struct wm8903_priv *wm8903 = snd_soc_component_get_drvdata(component);
        u16 reg;
        int ret;

        reg = snd_soc_component_read32(component, WM8903_CLASS_W_0);

        /* Turn it off if we're about to enable bypass */
        if (ucontrol->value.integer.value[0]) {
                if (wm8903->class_w_users == 0) {
                        dev_dbg(component->dev, "Disabling Class W\n");
                        snd_soc_component_write(component, WM8903_CLASS_W_0, reg &
                                     ~(WM8903_CP_DYN_FREQ | WM8903_CP_DYN_V));
                }
                wm8903->class_w_users++;
        }

        /* Implement the change */
        ret = snd_soc_dapm_put_volsw(kcontrol, ucontrol);

        /* If we've just disabled the last bypass path turn Class W on */
        if (!ucontrol->value.integer.value[0]) {
                if (wm8903->class_w_users == 1) {
                        dev_dbg(component->dev, "Enabling Class W\n");
                        snd_soc_component_write(component, WM8903_CLASS_W_0, reg |
                                     WM8903_CP_DYN_FREQ | WM8903_CP_DYN_V);
                }
                wm8903->class_w_users--;
        }

        dev_dbg(component->dev, "Bypass use count now %d\n",
                wm8903->class_w_users);

        return ret;
}

#define SOC_DAPM_SINGLE_W(xname, reg, shift, max, invert) \
        SOC_SINGLE_EXT(xname, reg, shift, max, invert, \
                snd_soc_dapm_get_volsw, wm8903_class_w_put)


static int wm8903_deemph[] = { 0, 32000, 44100, 48000 };

static int wm8903_set_deemph(struct snd_soc_component *component)
{
        struct wm8903_priv *wm8903 = snd_soc_component_get_drvdata(component);
        int val, i, best;

        /* If we're using deemphasis select the nearest available sample
         * rate.
         */
        if (wm8903->deemph) {
                best = 1;
                for (i = 2; i < ARRAY_SIZE(wm8903_deemph); i++) {
                        if (abs(wm8903_deemph[i] - wm8903->fs) <
                            abs(wm8903_deemph[best] - wm8903->fs))
                                best = i;
                }

                val = best << WM8903_DEEMPH_SHIFT;
        } else {
                best = 0;
                val = 0;
        }

        dev_dbg(component->dev, "Set deemphasis %d (%dHz)\n",
                best, wm8903_deemph[best]);

        return snd_soc_component_update_bits(component, WM8903_DAC_DIGITAL_1,
                                   WM8903_DEEMPH_MASK, val);
}

static int wm8903_get_deemph(struct snd_kcontrol *kcontrol,
                             struct snd_ctl_elem_value *ucontrol)
{
        struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol);
        struct wm8903_priv *wm8903 = snd_soc_component_get_drvdata(component);

        ucontrol->value.integer.value[0] = wm8903->deemph;

        return 0;
}

static int wm8903_put_deemph(struct snd_kcontrol *kcontrol,
                             struct snd_ctl_elem_value *ucontrol)
{
        struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol);
        struct wm8903_priv *wm8903 = snd_soc_component_get_drvdata(component);
        unsigned int deemph = ucontrol->value.integer.value[0];
        int ret = 0;

        if (deemph > 1)
                return -EINVAL;

        mutex_lock(&wm8903->lock);
        if (wm8903->deemph != deemph) {
                wm8903->deemph = deemph;

                wm8903_set_deemph(component);

                ret = 1;
        }
        mutex_unlock(&wm8903->lock);

        return ret;
}

/* ALSA can only do steps of .01dB */
static const DECLARE_TLV_DB_SCALE(digital_tlv, -7200, 75, 1);

static const DECLARE_TLV_DB_SCALE(dac_boost_tlv, 0, 600, 0);

static const DECLARE_TLV_DB_SCALE(digital_sidetone_tlv, -3600, 300, 0);
static const DECLARE_TLV_DB_SCALE(out_tlv, -5700, 100, 0);

static const DECLARE_TLV_DB_SCALE(drc_tlv_thresh, 0, 75, 0);
static const DECLARE_TLV_DB_SCALE(drc_tlv_amp, -2250, 75, 0);
static const DECLARE_TLV_DB_SCALE(drc_tlv_min, 0, 600, 0);
static const DECLARE_TLV_DB_SCALE(drc_tlv_max, 1200, 600, 0);
static const DECLARE_TLV_DB_SCALE(drc_tlv_startup, -300, 50, 0);

static const char *hpf_mode_text[] = {
        "Hi-fi", "Voice 1", "Voice 2", "Voice 3"
};

static SOC_ENUM_SINGLE_DECL(hpf_mode,
                            WM8903_ADC_DIGITAL_0, 5, hpf_mode_text);

static const char *osr_text[] = {
        "Low power", "High performance"
};

static SOC_ENUM_SINGLE_DECL(adc_osr,
                            WM8903_ANALOGUE_ADC_0, 0, osr_text);

static SOC_ENUM_SINGLE_DECL(dac_osr,
                            WM8903_DAC_DIGITAL_1, 0, osr_text);

static const char *drc_slope_text[] = {
        "1", "1/2", "1/4", "1/8", "1/16", "0"
};

static SOC_ENUM_SINGLE_DECL(drc_slope_r0,
                            WM8903_DRC_2, 3, drc_slope_text);

static SOC_ENUM_SINGLE_DECL(drc_slope_r1,
                            WM8903_DRC_2, 0, drc_slope_text);

static const char *drc_attack_text[] = {
        "instantaneous",
        "363us", "762us", "1.45ms", "2.9ms", "5.8ms", "11.6ms", "23.2ms",
        "46.4ms", "92.8ms", "185.6ms"
};

static SOC_ENUM_SINGLE_DECL(drc_attack,
                            WM8903_DRC_1, 12, drc_attack_text);

static const char *drc_decay_text[] = {
        "186ms", "372ms", "743ms", "1.49s", "2.97s", "5.94s", "11.89s",
        "23.87s", "47.56s"
};

static SOC_ENUM_SINGLE_DECL(drc_decay,
                            WM8903_DRC_1, 8, drc_decay_text);

static const char *drc_ff_delay_text[] = {
        "5 samples", "9 samples"
};

static SOC_ENUM_SINGLE_DECL(drc_ff_delay,
                            WM8903_DRC_0, 5, drc_ff_delay_text);

static const char *drc_qr_decay_text[] = {
        "0.725ms", "1.45ms", "5.8ms"
};

static SOC_ENUM_SINGLE_DECL(drc_qr_decay,
                            WM8903_DRC_1, 4, drc_qr_decay_text);

static const char *drc_smoothing_text[] = {
        "Low", "Medium", "High"
};

static SOC_ENUM_SINGLE_DECL(drc_smoothing,
                            WM8903_DRC_0, 11, drc_smoothing_text);

static const char *soft_mute_text[] = {
        "Fast (fs/2)", "Slow (fs/32)"
};

static SOC_ENUM_SINGLE_DECL(soft_mute,
                            WM8903_DAC_DIGITAL_1, 10, soft_mute_text);

static const char *mute_mode_text[] = {
        "Hard", "Soft"
};

static SOC_ENUM_SINGLE_DECL(mute_mode,
                            WM8903_DAC_DIGITAL_1, 9, mute_mode_text);

static const char *companding_text[] = {
        "ulaw", "alaw"
};

static SOC_ENUM_SINGLE_DECL(dac_companding,
                            WM8903_AUDIO_INTERFACE_0, 0, companding_text);

static SOC_ENUM_SINGLE_DECL(adc_companding,
                            WM8903_AUDIO_INTERFACE_0, 2, companding_text);

static const char *input_mode_text[] = {
        "Single-Ended", "Differential Line", "Differential Mic"
};

static SOC_ENUM_SINGLE_DECL(linput_mode_enum,
                            WM8903_ANALOGUE_LEFT_INPUT_1, 0, input_mode_text);

static SOC_ENUM_SINGLE_DECL(rinput_mode_enum,
                            WM8903_ANALOGUE_RIGHT_INPUT_1, 0, input_mode_text);

static const char *linput_mux_text[] = {
        "IN1L", "IN2L", "IN3L"
};

static SOC_ENUM_SINGLE_DECL(linput_enum,
                            WM8903_ANALOGUE_LEFT_INPUT_1, 2, linput_mux_text);

static SOC_ENUM_SINGLE_DECL(linput_inv_enum,
                            WM8903_ANALOGUE_LEFT_INPUT_1, 4, linput_mux_text);

static const char *rinput_mux_text[] = {
        "IN1R", "IN2R", "IN3R"
};

static SOC_ENUM_SINGLE_DECL(rinput_enum,
                            WM8903_ANALOGUE_RIGHT_INPUT_1, 2, rinput_mux_text);

static SOC_ENUM_SINGLE_DECL(rinput_inv_enum,
                            WM8903_ANALOGUE_RIGHT_INPUT_1, 4, rinput_mux_text);


static const char *sidetone_text[] = {
        "None", "Left", "Right"
};

static SOC_ENUM_SINGLE_DECL(lsidetone_enum,
                            WM8903_DAC_DIGITAL_0, 2, sidetone_text);

static SOC_ENUM_SINGLE_DECL(rsidetone_enum,
                            WM8903_DAC_DIGITAL_0, 0, sidetone_text);

static const char *adcinput_text[] = {
        "ADC", "DMIC"
};

static SOC_ENUM_SINGLE_DECL(adcinput_enum,
                            WM8903_CLOCK_RATE_TEST_4, 9, adcinput_text);

static const char *aif_text[] = {
        "Left", "Right"
};

static SOC_ENUM_SINGLE_DECL(lcapture_enum,
                            WM8903_AUDIO_INTERFACE_0, 7, aif_text);

static SOC_ENUM_SINGLE_DECL(rcapture_enum,
                            WM8903_AUDIO_INTERFACE_0, 6, aif_text);

static SOC_ENUM_SINGLE_DECL(lplay_enum,
                            WM8903_AUDIO_INTERFACE_0, 5, aif_text);

static SOC_ENUM_SINGLE_DECL(rplay_enum,
                            WM8903_AUDIO_INTERFACE_0, 4, aif_text);

static const struct snd_kcontrol_new wm8903_snd_controls[] = {

/* Input PGAs - No TLV since the scale depends on PGA mode */
SOC_SINGLE("Left Input PGA Switch", WM8903_ANALOGUE_LEFT_INPUT_0,
           7, 1, 1),
SOC_SINGLE("Left Input PGA Volume", WM8903_ANALOGUE_LEFT_INPUT_0,
           0, 31, 0),
SOC_SINGLE("Left Input PGA Common Mode Switch", WM8903_ANALOGUE_LEFT_INPUT_1,
           6, 1, 0),

SOC_SINGLE("Right Input PGA Switch", WM8903_ANALOGUE_RIGHT_INPUT_0,
           7, 1, 1),
SOC_SINGLE("Right Input PGA Volume", WM8903_ANALOGUE_RIGHT_INPUT_0,
           0, 31, 0),
SOC_SINGLE("Right Input PGA Common Mode Switch", WM8903_ANALOGUE_RIGHT_INPUT_1,
           6, 1, 0),

/* ADCs */
SOC_ENUM("ADC OSR", adc_osr),
SOC_SINGLE("HPF Switch", WM8903_ADC_DIGITAL_0, 4, 1, 0),
SOC_ENUM("HPF Mode", hpf_mode),
SOC_SINGLE("DRC Switch", WM8903_DRC_0, 15, 1, 0),
SOC_ENUM("DRC Compressor Slope R0", drc_slope_r0),
SOC_ENUM("DRC Compressor Slope R1", drc_slope_r1),
SOC_SINGLE_TLV("DRC Compressor Threshold Volume", WM8903_DRC_3, 5, 124, 1,
               drc_tlv_thresh),
SOC_SINGLE_TLV("DRC Volume", WM8903_DRC_3, 0, 30, 1, drc_tlv_amp),
SOC_SINGLE_TLV("DRC Minimum Gain Volume", WM8903_DRC_1, 2, 3, 1, drc_tlv_min),
SOC_SINGLE_TLV("DRC Maximum Gain Volume", WM8903_DRC_1, 0, 3, 0, drc_tlv_max),
SOC_ENUM("DRC Attack Rate", drc_attack),
SOC_ENUM("DRC Decay Rate", drc_decay),
SOC_ENUM("DRC FF Delay", drc_ff_delay),
SOC_SINGLE("DRC Anticlip Switch", WM8903_DRC_0, 1, 1, 0),
SOC_SINGLE("DRC QR Switch", WM8903_DRC_0, 2, 1, 0),
SOC_SINGLE_TLV("DRC QR Threshold Volume", WM8903_DRC_0, 6, 3, 0, drc_tlv_max),
SOC_ENUM("DRC QR Decay Rate", drc_qr_decay),
SOC_SINGLE("DRC Smoothing Switch", WM8903_DRC_0, 3, 1, 0),
SOC_SINGLE("DRC Smoothing Hysteresis Switch", WM8903_DRC_0, 0, 1, 0),
SOC_ENUM("DRC Smoothing Threshold", drc_smoothing),
SOC_SINGLE_TLV("DRC Startup Volume", WM8903_DRC_0, 6, 18, 0, drc_tlv_startup),

SOC_DOUBLE_R_TLV("Digital Capture Volume", WM8903_ADC_DIGITAL_VOLUME_LEFT,
                 WM8903_ADC_DIGITAL_VOLUME_RIGHT, 1, 120, 0, digital_tlv),
SOC_ENUM("ADC Companding Mode", adc_companding),
SOC_SINGLE("ADC Companding Switch", WM8903_AUDIO_INTERFACE_0, 3, 1, 0),

SOC_DOUBLE_TLV("Digital Sidetone Volume", WM8903_DAC_DIGITAL_0, 4, 8,
               12, 0, digital_sidetone_tlv),

/* DAC */
SOC_ENUM("DAC OSR", dac_osr),
SOC_DOUBLE_R_TLV("Digital Playback Volume", WM8903_DAC_DIGITAL_VOLUME_LEFT,
                 WM8903_DAC_DIGITAL_VOLUME_RIGHT, 1, 120, 0, digital_tlv),
SOC_ENUM("DAC Soft Mute Rate", soft_mute),
SOC_ENUM("DAC Mute Mode", mute_mode),
SOC_SINGLE("DAC Mono Switch", WM8903_DAC_DIGITAL_1, 12, 1, 0),
SOC_ENUM("DAC Companding Mode", dac_companding),
SOC_SINGLE("DAC Companding Switch", WM8903_AUDIO_INTERFACE_0, 1, 1, 0),
SOC_SINGLE_TLV("DAC Boost Volume", WM8903_AUDIO_INTERFACE_0, 9, 3, 0,
               dac_boost_tlv),
SOC_SINGLE_BOOL_EXT("Playback Deemphasis Switch", 0,
                    wm8903_get_deemph, wm8903_put_deemph),

/* Headphones */
SOC_DOUBLE_R("Headphone Switch",
             WM8903_ANALOGUE_OUT1_LEFT, WM8903_ANALOGUE_OUT1_RIGHT,
             8, 1, 1),
SOC_DOUBLE_R("Headphone ZC Switch",
             WM8903_ANALOGUE_OUT1_LEFT, WM8903_ANALOGUE_OUT1_RIGHT,
             6, 1, 0),
SOC_DOUBLE_R_TLV("Headphone Volume",
                 WM8903_ANALOGUE_OUT1_LEFT, WM8903_ANALOGUE_OUT1_RIGHT,
                 0, 63, 0, out_tlv),

/* Line out */
SOC_DOUBLE_R("Line Out Switch",
             WM8903_ANALOGUE_OUT2_LEFT, WM8903_ANALOGUE_OUT2_RIGHT,
             8, 1, 1),
SOC_DOUBLE_R("Line Out ZC Switch",
             WM8903_ANALOGUE_OUT2_LEFT, WM8903_ANALOGUE_OUT2_RIGHT,
             6, 1, 0),
SOC_DOUBLE_R_TLV("Line Out Volume",
                 WM8903_ANALOGUE_OUT2_LEFT, WM8903_ANALOGUE_OUT2_RIGHT,
                 0, 63, 0, out_tlv),

/* Speaker */
SOC_DOUBLE_R("Speaker Switch",
             WM8903_ANALOGUE_OUT3_LEFT, WM8903_ANALOGUE_OUT3_RIGHT, 8, 1, 1),
SOC_DOUBLE_R("Speaker ZC Switch",
             WM8903_ANALOGUE_OUT3_LEFT, WM8903_ANALOGUE_OUT3_RIGHT, 6, 1, 0),
SOC_DOUBLE_R_TLV("Speaker Volume",
                 WM8903_ANALOGUE_OUT3_LEFT, WM8903_ANALOGUE_OUT3_RIGHT,
                 0, 63, 0, out_tlv),
};

static const struct snd_kcontrol_new linput_mode_mux =
        SOC_DAPM_ENUM("Left Input Mode Mux", linput_mode_enum);

static const struct snd_kcontrol_new rinput_mode_mux =
        SOC_DAPM_ENUM("Right Input Mode Mux", rinput_mode_enum);

static const struct snd_kcontrol_new linput_mux =
        SOC_DAPM_ENUM("Left Input Mux", linput_enum);

static const struct snd_kcontrol_new linput_inv_mux =
        SOC_DAPM_ENUM("Left Inverting Input Mux", linput_inv_enum);

static const struct snd_kcontrol_new rinput_mux =
        SOC_DAPM_ENUM("Right Input Mux", rinput_enum);

static const struct snd_kcontrol_new rinput_inv_mux =
        SOC_DAPM_ENUM("Right Inverting Input Mux", rinput_inv_enum);

static const struct snd_kcontrol_new lsidetone_mux =
        SOC_DAPM_ENUM("DACL Sidetone Mux", lsidetone_enum);

static const struct snd_kcontrol_new rsidetone_mux =
        SOC_DAPM_ENUM("DACR Sidetone Mux", rsidetone_enum);

static const struct snd_kcontrol_new adcinput_mux =
        SOC_DAPM_ENUM("ADC Input", adcinput_enum);

static const struct snd_kcontrol_new lcapture_mux =
        SOC_DAPM_ENUM("Left Capture Mux", lcapture_enum);

static const struct snd_kcontrol_new rcapture_mux =
        SOC_DAPM_ENUM("Right Capture Mux", rcapture_enum);

static const struct snd_kcontrol_new lplay_mux =
        SOC_DAPM_ENUM("Left Playback Mux", lplay_enum);

static const struct snd_kcontrol_new rplay_mux =
        SOC_DAPM_ENUM("Right Playback Mux", rplay_enum);

static const struct snd_kcontrol_new left_output_mixer[] = {
SOC_DAPM_SINGLE("DACL Switch", WM8903_ANALOGUE_LEFT_MIX_0, 3, 1, 0),
SOC_DAPM_SINGLE("DACR Switch", WM8903_ANALOGUE_LEFT_MIX_0, 2, 1, 0),
SOC_DAPM_SINGLE_W("Left Bypass Switch", WM8903_ANALOGUE_LEFT_MIX_0, 1, 1, 0),
SOC_DAPM_SINGLE_W("Right Bypass Switch", WM8903_ANALOGUE_LEFT_MIX_0, 0, 1, 0),
};

static const struct snd_kcontrol_new right_output_mixer[] = {
SOC_DAPM_SINGLE("DACL Switch", WM8903_ANALOGUE_RIGHT_MIX_0, 3, 1, 0),
SOC_DAPM_SINGLE("DACR Switch", WM8903_ANALOGUE_RIGHT_MIX_0, 2, 1, 0),
SOC_DAPM_SINGLE_W("Left Bypass Switch", WM8903_ANALOGUE_RIGHT_MIX_0, 1, 1, 0),
SOC_DAPM_SINGLE_W("Right Bypass Switch", WM8903_ANALOGUE_RIGHT_MIX_0, 0, 1, 0),
};

static const struct snd_kcontrol_new left_speaker_mixer[] = {
SOC_DAPM_SINGLE("DACL Switch", WM8903_ANALOGUE_SPK_MIX_LEFT_0, 3, 1, 0),
SOC_DAPM_SINGLE("DACR Switch", WM8903_ANALOGUE_SPK_MIX_LEFT_0, 2, 1, 0),
SOC_DAPM_SINGLE("Left Bypass Switch", WM8903_ANALOGUE_SPK_MIX_LEFT_0, 1, 1, 0),
SOC_DAPM_SINGLE("Right Bypass Switch", WM8903_ANALOGUE_SPK_MIX_LEFT_0,
                0, 1, 0),
};

static const struct snd_kcontrol_new right_speaker_mixer[] = {
SOC_DAPM_SINGLE("DACL Switch", WM8903_ANALOGUE_SPK_MIX_RIGHT_0, 3, 1, 0),
SOC_DAPM_SINGLE("DACR Switch", WM8903_ANALOGUE_SPK_MIX_RIGHT_0, 2, 1, 0),
SOC_DAPM_SINGLE("Left Bypass Switch", WM8903_ANALOGUE_SPK_MIX_RIGHT_0,
                1, 1, 0),
SOC_DAPM_SINGLE("Right Bypass Switch", WM8903_ANALOGUE_SPK_MIX_RIGHT_0,
                0, 1, 0),
};

static const struct snd_soc_dapm_widget wm8903_dapm_widgets[] = {
SND_SOC_DAPM_INPUT("IN1L"),
SND_SOC_DAPM_INPUT("IN1R"),
SND_SOC_DAPM_INPUT("IN2L"),
SND_SOC_DAPM_INPUT("IN2R"),
SND_SOC_DAPM_INPUT("IN3L"),
SND_SOC_DAPM_INPUT("IN3R"),
SND_SOC_DAPM_INPUT("DMICDAT"),

SND_SOC_DAPM_OUTPUT("HPOUTL"),
SND_SOC_DAPM_OUTPUT("HPOUTR"),
SND_SOC_DAPM_OUTPUT("LINEOUTL"),
SND_SOC_DAPM_OUTPUT("LINEOUTR"),
SND_SOC_DAPM_OUTPUT("LOP"),
SND_SOC_DAPM_OUTPUT("LON"),
SND_SOC_DAPM_OUTPUT("ROP"),
SND_SOC_DAPM_OUTPUT("RON"),

SND_SOC_DAPM_SUPPLY("MICBIAS", WM8903_MIC_BIAS_CONTROL_0, 0, 0, NULL, 0),

SND_SOC_DAPM_MUX("Left Input Mux", SND_SOC_NOPM, 0, 0, &linput_mux),
SND_SOC_DAPM_MUX("Left Input Inverting Mux", SND_SOC_NOPM, 0, 0,
                 &linput_inv_mux),
SND_SOC_DAPM_MUX("Left Input Mode Mux", SND_SOC_NOPM, 0, 0, &linput_mode_mux),

SND_SOC_DAPM_MUX("Right Input Mux", SND_SOC_NOPM, 0, 0, &rinput_mux),
SND_SOC_DAPM_MUX("Right Input Inverting Mux", SND_SOC_NOPM, 0, 0,
                 &rinput_inv_mux),
SND_SOC_DAPM_MUX("Right Input Mode Mux", SND_SOC_NOPM, 0, 0, &rinput_mode_mux),

SND_SOC_DAPM_PGA("Left Input PGA", WM8903_POWER_MANAGEMENT_0, 1, 0, NULL, 0),
SND_SOC_DAPM_PGA("Right Input PGA", WM8903_POWER_MANAGEMENT_0, 0, 0, NULL, 0),

SND_SOC_DAPM_MUX("Left ADC Input", SND_SOC_NOPM, 0, 0, &adcinput_mux),
SND_SOC_DAPM_MUX("Right ADC Input", SND_SOC_NOPM, 0, 0, &adcinput_mux),

SND_SOC_DAPM_ADC("ADCL", NULL, WM8903_POWER_MANAGEMENT_6, 1, 0),
SND_SOC_DAPM_ADC("ADCR", NULL, WM8903_POWER_MANAGEMENT_6, 0, 0),

SND_SOC_DAPM_MUX("Left Capture Mux", SND_SOC_NOPM, 0, 0, &lcapture_mux),
SND_SOC_DAPM_MUX("Right Capture Mux", SND_SOC_NOPM, 0, 0, &rcapture_mux),

SND_SOC_DAPM_AIF_OUT("AIFTXL", "Left HiFi Capture", 0, SND_SOC_NOPM, 0, 0),
SND_SOC_DAPM_AIF_OUT("AIFTXR", "Right HiFi Capture", 0, SND_SOC_NOPM, 0, 0),

SND_SOC_DAPM_MUX("DACL Sidetone", SND_SOC_NOPM, 0, 0, &lsidetone_mux),
SND_SOC_DAPM_MUX("DACR Sidetone", SND_SOC_NOPM, 0, 0, &rsidetone_mux),

SND_SOC_DAPM_AIF_IN("AIFRXL", "Left Playback", 0, SND_SOC_NOPM, 0, 0),
SND_SOC_DAPM_AIF_IN("AIFRXR", "Right Playback", 0, SND_SOC_NOPM, 0, 0),

SND_SOC_DAPM_MUX("Left Playback Mux", SND_SOC_NOPM, 0, 0, &lplay_mux),
SND_SOC_DAPM_MUX("Right Playback Mux", SND_SOC_NOPM, 0, 0, &rplay_mux),

SND_SOC_DAPM_DAC("DACL", NULL, WM8903_POWER_MANAGEMENT_6, 3, 0),
SND_SOC_DAPM_DAC("DACR", NULL, WM8903_POWER_MANAGEMENT_6, 2, 0),

SND_SOC_DAPM_MIXER("Left Output Mixer", WM8903_POWER_MANAGEMENT_1, 1, 0,
                   left_output_mixer, ARRAY_SIZE(left_output_mixer)),
SND_SOC_DAPM_MIXER("Right Output Mixer", WM8903_POWER_MANAGEMENT_1, 0, 0,
                   right_output_mixer, ARRAY_SIZE(right_output_mixer)),

SND_SOC_DAPM_MIXER("Left Speaker Mixer", WM8903_POWER_MANAGEMENT_4, 1, 0,
                   left_speaker_mixer, ARRAY_SIZE(left_speaker_mixer)),
SND_SOC_DAPM_MIXER("Right Speaker Mixer", WM8903_POWER_MANAGEMENT_4, 0, 0,
                   right_speaker_mixer, ARRAY_SIZE(right_speaker_mixer)),

SND_SOC_DAPM_PGA_S("Left Headphone Output PGA", 0, WM8903_POWER_MANAGEMENT_2,
                   1, 0, NULL, 0),
SND_SOC_DAPM_PGA_S("Right Headphone Output PGA", 0, WM8903_POWER_MANAGEMENT_2,
                   0, 0, NULL, 0),

SND_SOC_DAPM_PGA_S("Left Line Output PGA", 0, WM8903_POWER_MANAGEMENT_3, 1, 0,
                   NULL, 0),
SND_SOC_DAPM_PGA_S("Right Line Output PGA", 0, WM8903_POWER_MANAGEMENT_3, 0, 0,
                   NULL, 0),

SND_SOC_DAPM_PGA_S("HPL_RMV_SHORT", 4, WM8903_ANALOGUE_HP_0, 7, 0, NULL, 0),
SND_SOC_DAPM_PGA_S("HPL_ENA_OUTP", 3, WM8903_ANALOGUE_HP_0, 6, 0, NULL, 0),
SND_SOC_DAPM_PGA_S("HPL_ENA_DLY", 2, WM8903_ANALOGUE_HP_0, 5, 0, NULL, 0),
SND_SOC_DAPM_PGA_S("HPL_ENA", 1, WM8903_ANALOGUE_HP_0, 4, 0, NULL, 0),
SND_SOC_DAPM_PGA_S("HPR_RMV_SHORT", 4, WM8903_ANALOGUE_HP_0, 3, 0, NULL, 0),
SND_SOC_DAPM_PGA_S("HPR_ENA_OUTP", 3, WM8903_ANALOGUE_HP_0, 2, 0, NULL, 0),
SND_SOC_DAPM_PGA_S("HPR_ENA_DLY", 2, WM8903_ANALOGUE_HP_0, 1, 0, NULL, 0),
SND_SOC_DAPM_PGA_S("HPR_ENA", 1, WM8903_ANALOGUE_HP_0, 0, 0, NULL, 0),

SND_SOC_DAPM_PGA_S("LINEOUTL_RMV_SHORT", 4, WM8903_ANALOGUE_LINEOUT_0, 7, 0,
                   NULL, 0),
SND_SOC_DAPM_PGA_S("LINEOUTL_ENA_OUTP", 3, WM8903_ANALOGUE_LINEOUT_0, 6, 0,
                   NULL, 0),
SND_SOC_DAPM_PGA_S("LINEOUTL_ENA_DLY", 2, WM8903_ANALOGUE_LINEOUT_0, 5, 0,
                   NULL, 0),
SND_SOC_DAPM_PGA_S("LINEOUTL_ENA", 1, WM8903_ANALOGUE_LINEOUT_0, 4, 0,
                   NULL, 0),
SND_SOC_DAPM_PGA_S("LINEOUTR_RMV_SHORT", 4, WM8903_ANALOGUE_LINEOUT_0, 3, 0,
                   NULL, 0),
SND_SOC_DAPM_PGA_S("LINEOUTR_ENA_OUTP", 3, WM8903_ANALOGUE_LINEOUT_0, 2, 0,
                   NULL, 0),
SND_SOC_DAPM_PGA_S("LINEOUTR_ENA_DLY", 2, WM8903_ANALOGUE_LINEOUT_0, 1, 0,
                   NULL, 0),
SND_SOC_DAPM_PGA_S("LINEOUTR_ENA", 1, WM8903_ANALOGUE_LINEOUT_0, 0, 0,
                   NULL, 0),

SND_SOC_DAPM_SUPPLY("DCS Master", WM8903_DC_SERVO_0, 4, 0, NULL, 0),
SND_SOC_DAPM_PGA_S("HPL_DCS", 3, SND_SOC_NOPM, 3, 0, wm8903_dcs_event,
                   SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD),
SND_SOC_DAPM_PGA_S("HPR_DCS", 3, SND_SOC_NOPM, 2, 0, wm8903_dcs_event,
                   SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD),
SND_SOC_DAPM_PGA_S("LINEOUTL_DCS", 3, SND_SOC_NOPM, 1, 0, wm8903_dcs_event,
                   SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD),
SND_SOC_DAPM_PGA_S("LINEOUTR_DCS", 3, SND_SOC_NOPM, 0, 0, wm8903_dcs_event,
                   SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD),

SND_SOC_DAPM_PGA("Left Speaker PGA", WM8903_POWER_MANAGEMENT_5, 1, 0,
                 NULL, 0),
SND_SOC_DAPM_PGA("Right Speaker PGA", WM8903_POWER_MANAGEMENT_5, 0, 0,
                 NULL, 0),

SND_SOC_DAPM_SUPPLY("Charge Pump", WM8903_CHARGE_PUMP_0, 0, 0,
                    wm8903_cp_event, SND_SOC_DAPM_POST_PMU),
SND_SOC_DAPM_SUPPLY("CLK_DSP", WM8903_CLOCK_RATES_2, 1, 0, NULL, 0),
SND_SOC_DAPM_SUPPLY("CLK_SYS", WM8903_CLOCK_RATES_2, 2, 0, NULL, 0),
};

static const struct snd_soc_dapm_route wm8903_intercon[] = {

        { "CLK_DSP", NULL, "CLK_SYS" },
        { "MICBIAS", NULL, "CLK_SYS" },
        { "HPL_DCS", NULL, "CLK_SYS" },
        { "HPR_DCS", NULL, "CLK_SYS" },
        { "LINEOUTL_DCS", NULL, "CLK_SYS" },
        { "LINEOUTR_DCS", NULL, "CLK_SYS" },

        { "Left Input Mux", "IN1L", "IN1L" },
        { "Left Input Mux", "IN2L", "IN2L" },
        { "Left Input Mux", "IN3L", "IN3L" },

        { "Left Input Inverting Mux", "IN1L", "IN1L" },
        { "Left Input Inverting Mux", "IN2L", "IN2L" },
        { "Left Input Inverting Mux", "IN3L", "IN3L" },

        { "Right Input Mux", "IN1R", "IN1R" },
        { "Right Input Mux", "IN2R", "IN2R" },
        { "Right Input Mux", "IN3R", "IN3R" },

        { "Right Input Inverting Mux", "IN1R", "IN1R" },
        { "Right Input Inverting Mux", "IN2R", "IN2R" },
        { "Right Input Inverting Mux", "IN3R", "IN3R" },

        { "Left Input Mode Mux", "Single-Ended", "Left Input Inverting Mux" },
        { "Left Input Mode Mux", "Differential Line",
          "Left Input Mux" },
        { "Left Input Mode Mux", "Differential Line",
          "Left Input Inverting Mux" },
        { "Left Input Mode Mux", "Differential Mic",
          "Left Input Mux" },
        { "Left Input Mode Mux", "Differential Mic",
          "Left Input Inverting Mux" },

        { "Right Input Mode Mux", "Single-Ended",
          "Right Input Inverting Mux" },
        { "Right Input Mode Mux", "Differential Line",
          "Right Input Mux" },
        { "Right Input Mode Mux", "Differential Line",
          "Right Input Inverting Mux" },
        { "Right Input Mode Mux", "Differential Mic",
          "Right Input Mux" },
        { "Right Input Mode Mux", "Differential Mic",
          "Right Input Inverting Mux" },

        { "Left Input PGA", NULL, "Left Input Mode Mux" },
        { "Right Input PGA", NULL, "Right Input Mode Mux" },

        { "Left ADC Input", "ADC", "Left Input PGA" },
        { "Left ADC Input", "DMIC", "DMICDAT" },
        { "Right ADC Input", "ADC", "Right Input PGA" },
        { "Right ADC Input", "DMIC", "DMICDAT" },

        { "Left Capture Mux", "Left", "ADCL" },
        { "Left Capture Mux", "Right", "ADCR" },

        { "Right Capture Mux", "Left", "ADCL" },
        { "Right Capture Mux", "Right", "ADCR" },

        { "AIFTXL", NULL, "Left Capture Mux" },
        { "AIFTXR", NULL, "Right Capture Mux" },

        { "ADCL", NULL, "Left ADC Input" },
        { "ADCL", NULL, "CLK_DSP" },
        { "ADCR", NULL, "Right ADC Input" },
        { "ADCR", NULL, "CLK_DSP" },

        { "Left Playback Mux", "Left", "AIFRXL" },
        { "Left Playback Mux", "Right", "AIFRXR" },

        { "Right Playback Mux", "Left", "AIFRXL" },
        { "Right Playback Mux", "Right", "AIFRXR" },

        { "DACL Sidetone", "Left", "ADCL" },
        { "DACL Sidetone", "Right", "ADCR" },
        { "DACR Sidetone", "Left", "ADCL" },
        { "DACR Sidetone", "Right", "ADCR" },

        { "DACL", NULL, "Left Playback Mux" },
        { "DACL", NULL, "DACL Sidetone" },
        { "DACL", NULL, "CLK_DSP" },

        { "DACR", NULL, "Right Playback Mux" },
        { "DACR", NULL, "DACR Sidetone" },
        { "DACR", NULL, "CLK_DSP" },

        { "Left Output Mixer", "Left Bypass Switch", "Left Input PGA" },
        { "Left Output Mixer", "Right Bypass Switch", "Right Input PGA" },
        { "Left Output Mixer", "DACL Switch", "DACL" },
        { "Left Output Mixer", "DACR Switch", "DACR" },

        { "Right Output Mixer", "Left Bypass Switch", "Left Input PGA" },
        { "Right Output Mixer", "Right Bypass Switch", "Right Input PGA" },
        { "Right Output Mixer", "DACL Switch", "DACL" },
        { "Right Output Mixer", "DACR Switch", "DACR" },

        { "Left Speaker Mixer", "Left Bypass Switch", "Left Input PGA" },
        { "Left Speaker Mixer", "Right Bypass Switch", "Right Input PGA" },
        { "Left Speaker Mixer", "DACL Switch", "DACL" },
        { "Left Speaker Mixer", "DACR Switch", "DACR" },

        { "Right Speaker Mixer", "Left Bypass Switch", "Left Input PGA" },
        { "Right Speaker Mixer", "Right Bypass Switch", "Right Input PGA" },
        { "Right Speaker Mixer", "DACL Switch", "DACL" },
        { "Right Speaker Mixer", "DACR Switch", "DACR" },

        { "Left Line Output PGA", NULL, "Left Output Mixer" },
        { "Right Line Output PGA", NULL, "Right Output Mixer" },

        { "Left Headphone Output PGA", NULL, "Left Output Mixer" },
        { "Right Headphone Output PGA", NULL, "Right Output Mixer" },

        { "Left Speaker PGA", NULL, "Left Speaker Mixer" },
        { "Right Speaker PGA", NULL, "Right Speaker Mixer" },

        { "HPL_ENA", NULL, "Left Headphone Output PGA" },
        { "HPR_ENA", NULL, "Right Headphone Output PGA" },
        { "HPL_ENA_DLY", NULL, "HPL_ENA" },
        { "HPR_ENA_DLY", NULL, "HPR_ENA" },
        { "LINEOUTL_ENA", NULL, "Left Line Output PGA" },
        { "LINEOUTR_ENA", NULL, "Right Line Output PGA" },
        { "LINEOUTL_ENA_DLY", NULL, "LINEOUTL_ENA" },
        { "LINEOUTR_ENA_DLY", NULL, "LINEOUTR_ENA" },

        { "HPL_DCS", NULL, "DCS Master" },
        { "HPR_DCS", NULL, "DCS Master" },
        { "LINEOUTL_DCS", NULL, "DCS Master" },
        { "LINEOUTR_DCS", NULL, "DCS Master" },

        { "HPL_DCS", NULL, "HPL_ENA_DLY" },
        { "HPR_DCS", NULL, "HPR_ENA_DLY" },
        { "LINEOUTL_DCS", NULL, "LINEOUTL_ENA_DLY" },
        { "LINEOUTR_DCS", NULL, "LINEOUTR_ENA_DLY" },

        { "HPL_ENA_OUTP", NULL, "HPL_DCS" },
        { "HPR_ENA_OUTP", NULL, "HPR_DCS" },
        { "LINEOUTL_ENA_OUTP", NULL, "LINEOUTL_DCS" },
        { "LINEOUTR_ENA_OUTP", NULL, "LINEOUTR_DCS" },

        { "HPL_RMV_SHORT", NULL, "HPL_ENA_OUTP" },
        { "HPR_RMV_SHORT", NULL, "HPR_ENA_OUTP" },
        { "LINEOUTL_RMV_SHORT", NULL, "LINEOUTL_ENA_OUTP" },
        { "LINEOUTR_RMV_SHORT", NULL, "LINEOUTR_ENA_OUTP" },

        { "HPOUTL", NULL, "HPL_RMV_SHORT" },
        { "HPOUTR", NULL, "HPR_RMV_SHORT" },
        { "LINEOUTL", NULL, "LINEOUTL_RMV_SHORT" },
        { "LINEOUTR", NULL, "LINEOUTR_RMV_SHORT" },

        { "LOP", NULL, "Left Speaker PGA" },
        { "LON", NULL, "Left Speaker PGA" },

        { "ROP", NULL, "Right Speaker PGA" },
        { "RON", NULL, "Right Speaker PGA" },

        { "Charge Pump", NULL, "CLK_DSP" },

        { "Left Headphone Output PGA", NULL, "Charge Pump" },
        { "Right Headphone Output PGA", NULL, "Charge Pump" },
        { "Left Line Output PGA", NULL, "Charge Pump" },
        { "Right Line Output PGA", NULL, "Charge Pump" },
};

static int wm8903_set_bias_level(struct snd_soc_component *component,
                                 enum snd_soc_bias_level level)
{
        switch (level) {
        case SND_SOC_BIAS_ON:
                break;

        case SND_SOC_BIAS_PREPARE:
                snd_soc_component_update_bits(component, WM8903_VMID_CONTROL_0,
                                    WM8903_VMID_RES_MASK,
                                    WM8903_VMID_RES_50K);
                break;

        case SND_SOC_BIAS_STANDBY:
                if (snd_soc_component_get_bias_level(component) == SND_SOC_BIAS_OFF) {
                        snd_soc_component_update_bits(component, WM8903_BIAS_CONTROL_0,
                                            WM8903_POBCTRL | WM8903_ISEL_MASK |
                                            WM8903_STARTUP_BIAS_ENA |
                                            WM8903_BIAS_ENA,
                                            WM8903_POBCTRL |
                                            (2 << WM8903_ISEL_SHIFT) |
                                            WM8903_STARTUP_BIAS_ENA);

                        snd_soc_component_update_bits(component,
                                            WM8903_ANALOGUE_SPK_OUTPUT_CONTROL_0,
                                            WM8903_SPK_DISCHARGE,
                                            WM8903_SPK_DISCHARGE);

                        msleep(33);

                        snd_soc_component_update_bits(component, WM8903_POWER_MANAGEMENT_5,
                                            WM8903_SPKL_ENA | WM8903_SPKR_ENA,
                                            WM8903_SPKL_ENA | WM8903_SPKR_ENA);

                        snd_soc_component_update_bits(component,
                                            WM8903_ANALOGUE_SPK_OUTPUT_CONTROL_0,
                                            WM8903_SPK_DISCHARGE, 0);

                        snd_soc_component_update_bits(component, WM8903_VMID_CONTROL_0,
                                            WM8903_VMID_TIE_ENA |
                                            WM8903_BUFIO_ENA |
                                            WM8903_VMID_IO_ENA |
                                            WM8903_VMID_SOFT_MASK |
                                            WM8903_VMID_RES_MASK |
                                            WM8903_VMID_BUF_ENA,
                                            WM8903_VMID_TIE_ENA |
                                            WM8903_BUFIO_ENA |
                                            WM8903_VMID_IO_ENA |
                                            (2 << WM8903_VMID_SOFT_SHIFT) |
                                            WM8903_VMID_RES_250K |
                                            WM8903_VMID_BUF_ENA);

                        msleep(129);

                        snd_soc_component_update_bits(component, WM8903_POWER_MANAGEMENT_5,
                                            WM8903_SPKL_ENA | WM8903_SPKR_ENA,
                                            0);

                        snd_soc_component_update_bits(component, WM8903_VMID_CONTROL_0,
                                            WM8903_VMID_SOFT_MASK, 0);

                        snd_soc_component_update_bits(component, WM8903_VMID_CONTROL_0,
                                            WM8903_VMID_RES_MASK,
                                            WM8903_VMID_RES_50K);

                        snd_soc_component_update_bits(component, WM8903_BIAS_CONTROL_0,
                                            WM8903_BIAS_ENA | WM8903_POBCTRL,
                                            WM8903_BIAS_ENA);

                        /* By default no bypass paths are enabled so
                         * enable Class W support.
                         */
                        dev_dbg(component->dev, "Enabling Class W\n");
                        snd_soc_component_update_bits(component, WM8903_CLASS_W_0,
                                            WM8903_CP_DYN_FREQ |
                                            WM8903_CP_DYN_V,
                                            WM8903_CP_DYN_FREQ |
                                            WM8903_CP_DYN_V);
                }

                snd_soc_component_update_bits(component, WM8903_VMID_CONTROL_0,
                                    WM8903_VMID_RES_MASK,
                                    WM8903_VMID_RES_250K);
                break;

        case SND_SOC_BIAS_OFF:
                snd_soc_component_update_bits(component, WM8903_BIAS_CONTROL_0,
                                    WM8903_BIAS_ENA, 0);

                snd_soc_component_update_bits(component, WM8903_VMID_CONTROL_0,
                                    WM8903_VMID_SOFT_MASK,
                                    2 << WM8903_VMID_SOFT_SHIFT);

                snd_soc_component_update_bits(component, WM8903_VMID_CONTROL_0,
                                    WM8903_VMID_BUF_ENA, 0);

                msleep(290);

                snd_soc_component_update_bits(component, WM8903_VMID_CONTROL_0,
                                    WM8903_VMID_TIE_ENA | WM8903_BUFIO_ENA |
                                    WM8903_VMID_IO_ENA | WM8903_VMID_RES_MASK |
                                    WM8903_VMID_SOFT_MASK |
                                    WM8903_VMID_BUF_ENA, 0);

                snd_soc_component_update_bits(component, WM8903_BIAS_CONTROL_0,
                                    WM8903_STARTUP_BIAS_ENA, 0);
                break;
        }

        return 0;
}

static int wm8903_set_dai_sysclk(struct snd_soc_dai *codec_dai,
                                 int clk_id, unsigned int freq, int dir)
{
        struct snd_soc_component *component = codec_dai->component;
        struct wm8903_priv *wm8903 = snd_soc_component_get_drvdata(component);

        wm8903->sysclk = freq;

        return 0;
}

static int wm8903_set_dai_fmt(struct snd_soc_dai *codec_dai,
                              unsigned int fmt)
{
        struct snd_soc_component *component = codec_dai->component;
        u16 aif1 = snd_soc_component_read32(component, WM8903_AUDIO_INTERFACE_1);

        aif1 &= ~(WM8903_LRCLK_DIR | WM8903_BCLK_DIR | WM8903_AIF_FMT_MASK |
                  WM8903_AIF_LRCLK_INV | WM8903_AIF_BCLK_INV);

        switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
        case SND_SOC_DAIFMT_CBS_CFS:
                break;
        case SND_SOC_DAIFMT_CBS_CFM:
                aif1 |= WM8903_LRCLK_DIR;
                break;
        case SND_SOC_DAIFMT_CBM_CFM:
                aif1 |= WM8903_LRCLK_DIR | WM8903_BCLK_DIR;
                break;
        case SND_SOC_DAIFMT_CBM_CFS:
                aif1 |= WM8903_BCLK_DIR;
                break;
        default:
                return -EINVAL;
        }

        switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
        case SND_SOC_DAIFMT_DSP_A:
                aif1 |= 0x3;
                break;
        case SND_SOC_DAIFMT_DSP_B:
                aif1 |= 0x3 | WM8903_AIF_LRCLK_INV;
                break;
        case SND_SOC_DAIFMT_I2S:
                aif1 |= 0x2;
                break;
        case SND_SOC_DAIFMT_RIGHT_J:
                aif1 |= 0x1;
                break;
        case SND_SOC_DAIFMT_LEFT_J:
                break;
        default:
                return -EINVAL;
        }

        /* Clock inversion */
        switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
        case SND_SOC_DAIFMT_DSP_A:
        case SND_SOC_DAIFMT_DSP_B:
                /* frame inversion not valid for DSP modes */
                switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
                case SND_SOC_DAIFMT_NB_NF:
                        break;
                case SND_SOC_DAIFMT_IB_NF:
                        aif1 |= WM8903_AIF_BCLK_INV;
                        break;
                default:
                        return -EINVAL;
                }
                break;
        case SND_SOC_DAIFMT_I2S:
        case SND_SOC_DAIFMT_RIGHT_J:
        case SND_SOC_DAIFMT_LEFT_J:
                switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
                case SND_SOC_DAIFMT_NB_NF:
                        break;
                case SND_SOC_DAIFMT_IB_IF:
                        aif1 |= WM8903_AIF_BCLK_INV | WM8903_AIF_LRCLK_INV;
                        break;
                case SND_SOC_DAIFMT_IB_NF:
                        aif1 |= WM8903_AIF_BCLK_INV;
                        break;
                case SND_SOC_DAIFMT_NB_IF:
                        aif1 |= WM8903_AIF_LRCLK_INV;
                        break;
                default:
                        return -EINVAL;
                }
                break;
        default:
                return -EINVAL;
        }

        snd_soc_component_write(component, WM8903_AUDIO_INTERFACE_1, aif1);

        return 0;
}

static int wm8903_digital_mute(struct snd_soc_dai *codec_dai, int mute)
{
        struct snd_soc_component *component = codec_dai->component;
        u16 reg;

        reg = snd_soc_component_read32(component, WM8903_DAC_DIGITAL_1);

        if (mute)
                reg |= WM8903_DAC_MUTE;
        else
                reg &= ~WM8903_DAC_MUTE;

        snd_soc_component_write(component, WM8903_DAC_DIGITAL_1, reg);

        return 0;
}

/* Lookup table for CLK_SYS/fs ratio.  256fs or more is recommended
 * for optimal performance so we list the lower rates first and match
 * on the last match we find. */
static struct {
        int div;
        int rate;
        int mode;
        int mclk_div;
} clk_sys_ratios[] = {
        {   64, 0x0, 0x0, 1 },
        {   68, 0x0, 0x1, 1 },
        {  125, 0x0, 0x2, 1 },
        {  128, 0x1, 0x0, 1 },
        {  136, 0x1, 0x1, 1 },
        {  192, 0x2, 0x0, 1 },
        {  204, 0x2, 0x1, 1 },

        {   64, 0x0, 0x0, 2 },
        {   68, 0x0, 0x1, 2 },
        {  125, 0x0, 0x2, 2 },
        {  128, 0x1, 0x0, 2 },
        {  136, 0x1, 0x1, 2 },
        {  192, 0x2, 0x0, 2 },
        {  204, 0x2, 0x1, 2 },

        {  250, 0x2, 0x2, 1 },
        {  256, 0x3, 0x0, 1 },
        {  272, 0x3, 0x1, 1 },
        {  384, 0x4, 0x0, 1 },
        {  408, 0x4, 0x1, 1 },
        {  375, 0x4, 0x2, 1 },
        {  512, 0x5, 0x0, 1 },
        {  544, 0x5, 0x1, 1 },
        {  500, 0x5, 0x2, 1 },
        {  768, 0x6, 0x0, 1 },
        {  816, 0x6, 0x1, 1 },
        {  750, 0x6, 0x2, 1 },
        { 1024, 0x7, 0x0, 1 },
        { 1088, 0x7, 0x1, 1 },
        { 1000, 0x7, 0x2, 1 },
        { 1408, 0x8, 0x0, 1 },
        { 1496, 0x8, 0x1, 1 },
        { 1536, 0x9, 0x0, 1 },
        { 1632, 0x9, 0x1, 1 },
        { 1500, 0x9, 0x2, 1 },

        {  250, 0x2, 0x2, 2 },
        {  256, 0x3, 0x0, 2 },
        {  272, 0x3, 0x1, 2 },
        {  384, 0x4, 0x0, 2 },
        {  408, 0x4, 0x1, 2 },
        {  375, 0x4, 0x2, 2 },
        {  512, 0x5, 0x0, 2 },
        {  544, 0x5, 0x1, 2 },
        {  500, 0x5, 0x2, 2 },
        {  768, 0x6, 0x0, 2 },
        {  816, 0x6, 0x1, 2 },
        {  750, 0x6, 0x2, 2 },
        { 1024, 0x7, 0x0, 2 },
        { 1088, 0x7, 0x1, 2 },
        { 1000, 0x7, 0x2, 2 },
        { 1408, 0x8, 0x0, 2 },
        { 1496, 0x8, 0x1, 2 },
        { 1536, 0x9, 0x0, 2 },
        { 1632, 0x9, 0x1, 2 },
        { 1500, 0x9, 0x2, 2 },
};

/* CLK_SYS/BCLK ratios - multiplied by 10 due to .5s */
static struct {
        int ratio;
        int div;
} bclk_divs[] = {
        {  10,  0 },
        {  20,  2 },
        {  30,  3 },
        {  40,  4 },
        {  50,  5 },
        {  60,  7 },
        {  80,  8 },
        { 100,  9 },
        { 120, 11 },
        { 160, 12 },
        { 200, 13 },
        { 220, 14 },
        { 240, 15 },
        { 300, 17 },
        { 320, 18 },
        { 440, 19 },
        { 480, 20 },
};

/* Sample rates for DSP */
static struct {
        int rate;
        int value;
} sample_rates[] = {
        {  8000,  0 },
        { 11025,  1 },
        { 12000,  2 },
        { 16000,  3 },
        { 22050,  4 },
        { 24000,  5 },
        { 32000,  6 },
        { 44100,  7 },
        { 48000,  8 },
        { 88200,  9 },
        { 96000, 10 },
        { 0,      0 },
};

static int wm8903_hw_params(struct snd_pcm_substream *substream,
                            struct snd_pcm_hw_params *params,
                            struct snd_soc_dai *dai)
{
        struct snd_soc_component *component = dai->component;
        struct wm8903_priv *wm8903 = snd_soc_component_get_drvdata(component);
        int fs = params_rate(params);
        int bclk;
        int bclk_div;
        int i;
        int dsp_config;
        int clk_config;
        int best_val;
        int cur_val;
        int clk_sys;

        u16 aif1 = snd_soc_component_read32(component, WM8903_AUDIO_INTERFACE_1);
        u16 aif2 = snd_soc_component_read32(component, WM8903_AUDIO_INTERFACE_2);
        u16 aif3 = snd_soc_component_read32(component, WM8903_AUDIO_INTERFACE_3);
        u16 clock0 = snd_soc_component_read32(component, WM8903_CLOCK_RATES_0);
        u16 clock1 = snd_soc_component_read32(component, WM8903_CLOCK_RATES_1);
        u16 dac_digital1 = snd_soc_component_read32(component, WM8903_DAC_DIGITAL_1);

        /* Enable sloping stopband filter for low sample rates */
        if (fs <= 24000)
                dac_digital1 |= WM8903_DAC_SB_FILT;
        else
                dac_digital1 &= ~WM8903_DAC_SB_FILT;

        /* Configure sample rate logic for DSP - choose nearest rate */
        dsp_config = 0;
        best_val = abs(sample_rates[dsp_config].rate - fs);
        for (i = 1; i < ARRAY_SIZE(sample_rates); i++) {
                cur_val = abs(sample_rates[i].rate - fs);
                if (cur_val <= best_val) {
                        dsp_config = i;
                        best_val = cur_val;
                }
        }

        dev_dbg(component->dev, "DSP fs = %dHz\n", sample_rates[dsp_config].rate);
        clock1 &= ~WM8903_SAMPLE_RATE_MASK;
        clock1 |= sample_rates[dsp_config].value;

        aif1 &= ~WM8903_AIF_WL_MASK;
        bclk = 2 * fs;
        switch (params_width(params)) {
        case 16:
                bclk *= 16;
                break;
        case 20:
                bclk *= 20;
                aif1 |= 0x4;
                break;
        case 24:
                bclk *= 24;
                aif1 |= 0x8;
                break;
        case 32:
                bclk *= 32;
                aif1 |= 0xc;
                break;
        default:
                return -EINVAL;
        }

        dev_dbg(component->dev, "MCLK = %dHz, target sample rate = %dHz\n",
                wm8903->sysclk, fs);

        /* We may not have an MCLK which allows us to generate exactly
         * the clock we want, particularly with USB derived inputs, so
         * approximate.
         */
        clk_config = 0;
        best_val = abs((wm8903->sysclk /
                        (clk_sys_ratios[0].mclk_div *
                         clk_sys_ratios[0].div)) - fs);
        for (i = 1; i < ARRAY_SIZE(clk_sys_ratios); i++) {
                cur_val = abs((wm8903->sysclk /
                               (clk_sys_ratios[i].mclk_div *
                                clk_sys_ratios[i].div)) - fs);

                if (cur_val <= best_val) {
                        clk_config = i;
                        best_val = cur_val;
                }
        }

        if (clk_sys_ratios[clk_config].mclk_div == 2) {
                clock0 |= WM8903_MCLKDIV2;
                clk_sys = wm8903->sysclk / 2;
        } else {
                clock0 &= ~WM8903_MCLKDIV2;
                clk_sys = wm8903->sysclk;
        }

        clock1 &= ~(WM8903_CLK_SYS_RATE_MASK |
                    WM8903_CLK_SYS_MODE_MASK);
        clock1 |= clk_sys_ratios[clk_config].rate << WM8903_CLK_SYS_RATE_SHIFT;
        clock1 |= clk_sys_ratios[clk_config].mode << WM8903_CLK_SYS_MODE_SHIFT;

        dev_dbg(component->dev, "CLK_SYS_RATE=%x, CLK_SYS_MODE=%x div=%d\n",
                clk_sys_ratios[clk_config].rate,
                clk_sys_ratios[clk_config].mode,
                clk_sys_ratios[clk_config].div);

        dev_dbg(component->dev, "Actual CLK_SYS = %dHz\n", clk_sys);

        /* We may not get quite the right frequency if using
         * approximate clocks so look for the closest match that is
         * higher than the target (we need to ensure that there enough
         * BCLKs to clock out the samples).
         */
        bclk_div = 0;
        best_val = ((clk_sys * 10) / bclk_divs[0].ratio) - bclk;
        i = 1;
        while (i < ARRAY_SIZE(bclk_divs)) {
                cur_val = ((clk_sys * 10) / bclk_divs[i].ratio) - bclk;
                if (cur_val < 0) /* BCLK table is sorted */
                        break;
                bclk_div = i;
                best_val = cur_val;
                i++;
        }

        aif2 &= ~WM8903_BCLK_DIV_MASK;
        aif3 &= ~WM8903_LRCLK_RATE_MASK;

        dev_dbg(component->dev, "BCLK ratio %d for %dHz - actual BCLK = %dHz\n",
                bclk_divs[bclk_div].ratio / 10, bclk,
                (clk_sys * 10) / bclk_divs[bclk_div].ratio);

        aif2 |= bclk_divs[bclk_div].div;
        aif3 |= bclk / fs;

        wm8903->fs = params_rate(params);
        wm8903_set_deemph(component);

        snd_soc_component_write(component, WM8903_CLOCK_RATES_0, clock0);
        snd_soc_component_write(component, WM8903_CLOCK_RATES_1, clock1);
        snd_soc_component_write(component, WM8903_AUDIO_INTERFACE_1, aif1);
        snd_soc_component_write(component, WM8903_AUDIO_INTERFACE_2, aif2);
        snd_soc_component_write(component, WM8903_AUDIO_INTERFACE_3, aif3);
        snd_soc_component_write(component, WM8903_DAC_DIGITAL_1, dac_digital1);

        return 0;
}

/**
 * wm8903_mic_detect - Enable microphone detection via the WM8903 IRQ
 *
 * @component:  WM8903 component
 * @jack:   jack to report detection events on
 * @det:    value to report for presence detection
 * @shrt:   value to report for short detection
 *
 * Enable microphone detection via IRQ on the WM8903.  If GPIOs are
 * being used to bring out signals to the processor then only platform
 * data configuration is needed for WM8903 and processor GPIOs should
 * be configured using snd_soc_jack_add_gpios() instead.
 *
 * The current threasholds for detection should be configured using
 * micdet_cfg in the platform data.  Using this function will force on
 * the microphone bias for the device.
 */
int wm8903_mic_detect(struct snd_soc_component *component, struct snd_soc_jack *jack,
                      int det, int shrt)
{
        struct wm8903_priv *wm8903 = snd_soc_component_get_drvdata(component);
        int irq_mask = WM8903_MICDET_EINT | WM8903_MICSHRT_EINT;

        dev_dbg(component->dev, "Enabling microphone detection: %x %x\n",
                det, shrt);

        /* Store the configuration */
        wm8903->mic_jack = jack;
        wm8903->mic_det = det;
        wm8903->mic_short = shrt;

        /* Enable interrupts we've got a report configured for */
        if (det)
                irq_mask &= ~WM8903_MICDET_EINT;
        if (shrt)
                irq_mask &= ~WM8903_MICSHRT_EINT;

        snd_soc_component_update_bits(component, WM8903_INTERRUPT_STATUS_1_MASK,
                            WM8903_MICDET_EINT | WM8903_MICSHRT_EINT,
                            irq_mask);

        if (det || shrt) {
                /* Enable mic detection, this may not have been set through
                 * platform data (eg, if the defaults are OK). */
                snd_soc_component_update_bits(component, WM8903_WRITE_SEQUENCER_0,
                                    WM8903_WSEQ_ENA, WM8903_WSEQ_ENA);
                snd_soc_component_update_bits(component, WM8903_MIC_BIAS_CONTROL_0,
                                    WM8903_MICDET_ENA, WM8903_MICDET_ENA);
        } else {
                snd_soc_component_update_bits(component, WM8903_MIC_BIAS_CONTROL_0,
                                    WM8903_MICDET_ENA, 0);
        }

        return 0;
}
EXPORT_SYMBOL_GPL(wm8903_mic_detect);

static irqreturn_t wm8903_irq(int irq, void *data)
{
        struct wm8903_priv *wm8903 = data;
        int mic_report, ret;
        unsigned int int_val, mask, int_pol;

        ret = regmap_read(wm8903->regmap, WM8903_INTERRUPT_STATUS_1_MASK,
                          &mask);
        if (ret != 0) {
                dev_err(wm8903->dev, "Failed to read IRQ mask: %d\n", ret);
                return IRQ_NONE;
        }

        ret = regmap_read(wm8903->regmap, WM8903_INTERRUPT_STATUS_1, &int_val);
        if (ret != 0) {
                dev_err(wm8903->dev, "Failed to read IRQ status: %d\n", ret);
                return IRQ_NONE;
        }

        int_val &= ~mask;

        if (int_val & WM8903_WSEQ_BUSY_EINT) {
                dev_warn(wm8903->dev, "Write sequencer done\n");
        }

        /*
         * The rest is microphone jack detection.  We need to manually
         * invert the polarity of the interrupt after each event - to
         * simplify the code keep track of the last state we reported
         * and just invert the relevant bits in both the report and
         * the polarity register.
         */
        mic_report = wm8903->mic_last_report;
        ret = regmap_read(wm8903->regmap, WM8903_INTERRUPT_POLARITY_1,
                          &int_pol);
        if (ret != 0) {
                dev_err(wm8903->dev, "Failed to read interrupt polarity: %d\n",
                        ret);
                return IRQ_HANDLED;
        }

#ifndef CONFIG_SND_SOC_WM8903_MODULE
        if (int_val & (WM8903_MICSHRT_EINT | WM8903_MICDET_EINT))
                trace_snd_soc_jack_irq(dev_name(wm8903->dev));
#endif

        if (int_val & WM8903_MICSHRT_EINT) {
                dev_dbg(wm8903->dev, "Microphone short (pol=%x)\n", int_pol);

                mic_report ^= wm8903->mic_short;
                int_pol ^= WM8903_MICSHRT_INV;
        }

        if (int_val & WM8903_MICDET_EINT) {
                dev_dbg(wm8903->dev, "Microphone detect (pol=%x)\n", int_pol);

                mic_report ^= wm8903->mic_det;
                int_pol ^= WM8903_MICDET_INV;

                msleep(wm8903->mic_delay);
        }

        regmap_update_bits(wm8903->regmap, WM8903_INTERRUPT_POLARITY_1,
                           WM8903_MICSHRT_INV | WM8903_MICDET_INV, int_pol);

        snd_soc_jack_report(wm8903->mic_jack, mic_report,
                            wm8903->mic_short | wm8903->mic_det);

        wm8903->mic_last_report = mic_report;

        return IRQ_HANDLED;
}

#define WM8903_PLAYBACK_RATES (SNDRV_PCM_RATE_8000 |\
                               SNDRV_PCM_RATE_11025 |   \
                               SNDRV_PCM_RATE_16000 |   \
                               SNDRV_PCM_RATE_22050 |   \
                               SNDRV_PCM_RATE_32000 |   \
                               SNDRV_PCM_RATE_44100 |   \
                               SNDRV_PCM_RATE_48000 |   \
                               SNDRV_PCM_RATE_88200 |   \
                               SNDRV_PCM_RATE_96000)

#define WM8903_CAPTURE_RATES (SNDRV_PCM_RATE_8000 |\
                              SNDRV_PCM_RATE_11025 |    \
                              SNDRV_PCM_RATE_16000 |    \
                              SNDRV_PCM_RATE_22050 |    \
                              SNDRV_PCM_RATE_32000 |    \
                              SNDRV_PCM_RATE_44100 |    \
                              SNDRV_PCM_RATE_48000)

#define WM8903_FORMATS (SNDRV_PCM_FMTBIT_S16_LE |\
                        SNDRV_PCM_FMTBIT_S20_3LE |\
                        SNDRV_PCM_FMTBIT_S24_LE)

static const struct snd_soc_dai_ops wm8903_dai_ops = {
        .hw_params      = wm8903_hw_params,
        .digital_mute   = wm8903_digital_mute,
        .set_fmt        = wm8903_set_dai_fmt,
        .set_sysclk     = wm8903_set_dai_sysclk,
};

static struct snd_soc_dai_driver wm8903_dai = {
        .name = "wm8903-hifi",
        .playback = {
                .stream_name = "Playback",
                .channels_min = 2,
                .channels_max = 2,
                .rates = WM8903_PLAYBACK_RATES,
                .formats = WM8903_FORMATS,
        },
        .capture = {
                 .stream_name = "Capture",
                 .channels_min = 2,
                 .channels_max = 2,
                 .rates = WM8903_CAPTURE_RATES,
                 .formats = WM8903_FORMATS,
         },
        .ops = &wm8903_dai_ops,
        .symmetric_rates = 1,
};

static int wm8903_resume(struct snd_soc_component *component)
{
        struct wm8903_priv *wm8903 = snd_soc_component_get_drvdata(component);

        regcache_sync(wm8903->regmap);

        return 0;
}

#ifdef CONFIG_GPIOLIB
static int wm8903_gpio_request(struct gpio_chip *chip, unsigned offset)
{
        if (offset >= WM8903_NUM_GPIO)
                return -EINVAL;

        return 0;
}

static int wm8903_gpio_direction_in(struct gpio_chip *chip, unsigned offset)
{
        struct wm8903_priv *wm8903 = gpiochip_get_data(chip);
        unsigned int mask, val;
        int ret;

        mask = WM8903_GP1_FN_MASK | WM8903_GP1_DIR_MASK;
        val = (WM8903_GPn_FN_GPIO_INPUT << WM8903_GP1_FN_SHIFT) |
                WM8903_GP1_DIR;

        ret = regmap_update_bits(wm8903->regmap,
                                 WM8903_GPIO_CONTROL_1 + offset, mask, val);
        if (ret < 0)
                return ret;

        return 0;
}

static int wm8903_gpio_get(struct gpio_chip *chip, unsigned offset)
{
        struct wm8903_priv *wm8903 = gpiochip_get_data(chip);
        unsigned int reg;

        regmap_read(wm8903->regmap, WM8903_GPIO_CONTROL_1 + offset, &reg);

        return !!((reg & WM8903_GP1_LVL_MASK) >> WM8903_GP1_LVL_SHIFT);
}

static int wm8903_gpio_direction_out(struct gpio_chip *chip,
                                     unsigned offset, int value)
{
        struct wm8903_priv *wm8903 = gpiochip_get_data(chip);
        unsigned int mask, val;
        int ret;

        mask = WM8903_GP1_FN_MASK | WM8903_GP1_DIR_MASK | WM8903_GP1_LVL_MASK;
        val = (WM8903_GPn_FN_GPIO_OUTPUT << WM8903_GP1_FN_SHIFT) |
                (value << WM8903_GP2_LVL_SHIFT);

        ret = regmap_update_bits(wm8903->regmap,
                                 WM8903_GPIO_CONTROL_1 + offset, mask, val);
        if (ret < 0)
                return ret;

        return 0;
}

static void wm8903_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
{
        struct wm8903_priv *wm8903 = gpiochip_get_data(chip);

        regmap_update_bits(wm8903->regmap, WM8903_GPIO_CONTROL_1 + offset,
                           WM8903_GP1_LVL_MASK,
                           !!value << WM8903_GP1_LVL_SHIFT);
}

static const struct gpio_chip wm8903_template_chip = {
        .label                  = "wm8903",
        .owner                  = THIS_MODULE,
        .request                = wm8903_gpio_request,
        .direction_input        = wm8903_gpio_direction_in,
        .get                    = wm8903_gpio_get,
        .direction_output       = wm8903_gpio_direction_out,
        .set                    = wm8903_gpio_set,
        .can_sleep              = 1,
};

static void wm8903_init_gpio(struct wm8903_priv *wm8903)
{
        struct wm8903_platform_data *pdata = wm8903->pdata;
        int ret;

        wm8903->gpio_chip = wm8903_template_chip;
        wm8903->gpio_chip.ngpio = WM8903_NUM_GPIO;
        wm8903->gpio_chip.parent = wm8903->dev;

        if (pdata->gpio_base)
                wm8903->gpio_chip.base = pdata->gpio_base;
        else
                wm8903->gpio_chip.base = -1;

        ret = gpiochip_add_data(&wm8903->gpio_chip, wm8903);
        if (ret != 0)
                dev_err(wm8903->dev, "Failed to add GPIOs: %d\n", ret);
}

static void wm8903_free_gpio(struct wm8903_priv *wm8903)
{
        gpiochip_remove(&wm8903->gpio_chip);
}
#else
static void wm8903_init_gpio(struct wm8903_priv *wm8903)
{
}

static void wm8903_free_gpio(struct wm8903_priv *wm8903)
{
}
#endif

static const struct snd_soc_component_driver soc_component_dev_wm8903 = {
        .resume                 = wm8903_resume,
        .set_bias_level         = wm8903_set_bias_level,
        .seq_notifier           = wm8903_seq_notifier,
        .controls               = wm8903_snd_controls,
        .num_controls           = ARRAY_SIZE(wm8903_snd_controls),
        .dapm_widgets           = wm8903_dapm_widgets,
        .num_dapm_widgets       = ARRAY_SIZE(wm8903_dapm_widgets),
        .dapm_routes            = wm8903_intercon,
        .num_dapm_routes        = ARRAY_SIZE(wm8903_intercon),
        .suspend_bias_off       = 1,
        .idle_bias_on           = 1,
        .use_pmdown_time        = 1,
        .endianness             = 1,
        .non_legacy_dai_naming  = 1,
};

static const struct regmap_config wm8903_regmap = {
        .reg_bits = 8,
        .val_bits = 16,

        .max_register = WM8903_MAX_REGISTER,
        .volatile_reg = wm8903_volatile_register,
        .readable_reg = wm8903_readable_register,

        .cache_type = REGCACHE_RBTREE,
        .reg_defaults = wm8903_reg_defaults,
        .num_reg_defaults = ARRAY_SIZE(wm8903_reg_defaults),
};

static int wm8903_set_pdata_irq_trigger(struct i2c_client *i2c,
                                        struct wm8903_platform_data *pdata)
{
        struct irq_data *irq_data = irq_get_irq_data(i2c->irq);
        if (!irq_data) {
                dev_err(&i2c->dev, "Invalid IRQ: %d\n",
                        i2c->irq);
                return -EINVAL;
        }

        switch (irqd_get_trigger_type(irq_data)) {
        case IRQ_TYPE_NONE:
        default:
                /*
                * We assume the controller imposes no restrictions,
                * so we are able to select active-high
                */
                /* Fall-through */
        case IRQ_TYPE_LEVEL_HIGH:
                pdata->irq_active_low = false;
                break;
        case IRQ_TYPE_LEVEL_LOW:
                pdata->irq_active_low = true;
                break;
        }

        return 0;
}

static int wm8903_set_pdata_from_of(struct i2c_client *i2c,
                                    struct wm8903_platform_data *pdata)
{
        const struct device_node *np = i2c->dev.of_node;
        u32 val32;
        int i;

        if (of_property_read_u32(np, "micdet-cfg", &val32) >= 0)
                pdata->micdet_cfg = val32;

        if (of_property_read_u32(np, "micdet-delay", &val32) >= 0)
                pdata->micdet_delay = val32;

        if (of_property_read_u32_array(np, "gpio-cfg", pdata->gpio_cfg,
                                       ARRAY_SIZE(pdata->gpio_cfg)) >= 0) {
                /*
                 * In device tree: 0 means "write 0",
                 * 0xffffffff means "don't touch".
                 *
                 * In platform data: 0 means "don't touch",
                 * 0x8000 means "write 0".
                 *
                 * Note: WM8903_GPIO_CONFIG_ZERO == 0x8000.
                 *
                 *  Convert from DT to pdata representation here,
                 * so no other code needs to change.
                 */
                for (i = 0; i < ARRAY_SIZE(pdata->gpio_cfg); i++) {
                        if (pdata->gpio_cfg[i] == 0) {
                                pdata->gpio_cfg[i] = WM8903_GPIO_CONFIG_ZERO;
                        } else if (pdata->gpio_cfg[i] == 0xffffffff) {
                                pdata->gpio_cfg[i] = 0;
                        } else if (pdata->gpio_cfg[i] > 0x7fff) {
                                dev_err(&i2c->dev, "Invalid gpio-cfg[%d] %x\n",
                                        i, pdata->gpio_cfg[i]);
                                return -EINVAL;
                        }
                }
        }

        return 0;
}

static int wm8903_i2c_probe(struct i2c_client *i2c,
                            const struct i2c_device_id *id)
{
        struct wm8903_platform_data *pdata = dev_get_platdata(&i2c->dev);
        struct wm8903_priv *wm8903;
        int trigger;
        bool mic_gpio = false;
        unsigned int val, irq_pol;
        int ret, i;

        wm8903 = devm_kzalloc(&i2c->dev, sizeof(*wm8903), GFP_KERNEL);
        if (wm8903 == NULL)
                return -ENOMEM;

        mutex_init(&wm8903->lock);
        wm8903->dev = &i2c->dev;

        wm8903->regmap = devm_regmap_init_i2c(i2c, &wm8903_regmap);
        if (IS_ERR(wm8903->regmap)) {
                ret = PTR_ERR(wm8903->regmap);
                dev_err(&i2c->dev, "Failed to allocate register map: %d\n",
                        ret);
                return ret;
        }

        i2c_set_clientdata(i2c, wm8903);

        /* If no platform data was supplied, create storage for defaults */
        if (pdata) {
                wm8903->pdata = pdata;
        } else {
                wm8903->pdata = devm_kzalloc(&i2c->dev, sizeof(*wm8903->pdata),
                                             GFP_KERNEL);
                if (!wm8903->pdata)
                        return -ENOMEM;

                if (i2c->irq) {
                        ret = wm8903_set_pdata_irq_trigger(i2c, wm8903->pdata);
                        if (ret != 0)
                                return ret;
                }

                if (i2c->dev.of_node) {
                        ret = wm8903_set_pdata_from_of(i2c, wm8903->pdata);
                        if (ret != 0)
                                return ret;
                }
        }

        pdata = wm8903->pdata;

        for (i = 0; i < ARRAY_SIZE(wm8903->supplies); i++)
                wm8903->supplies[i].supply = wm8903_supply_names[i];

        ret = devm_regulator_bulk_get(&i2c->dev, ARRAY_SIZE(wm8903->supplies),
                                      wm8903->supplies);
        if (ret != 0) {
                dev_err(&i2c->dev, "Failed to request supplies: %d\n", ret);
                return ret;
        }

        ret = regulator_bulk_enable(ARRAY_SIZE(wm8903->supplies),
                                    wm8903->supplies);
        if (ret != 0) {
                dev_err(&i2c->dev, "Failed to enable supplies: %d\n", ret);
                return ret;
        }

        ret = regmap_read(wm8903->regmap, WM8903_SW_RESET_AND_ID, &val);
        if (ret != 0) {
                dev_err(&i2c->dev, "Failed to read chip ID: %d\n", ret);
                goto err;
        }
        if (val != 0x8903) {
                dev_err(&i2c->dev, "Device with ID %x is not a WM8903\n", val);
                ret = -ENODEV;
                goto err;
        }

        ret = regmap_read(wm8903->regmap, WM8903_REVISION_NUMBER, &val);
        if (ret != 0) {
                dev_err(&i2c->dev, "Failed to read chip revision: %d\n", ret);
                goto err;
        }
        dev_info(&i2c->dev, "WM8903 revision %c\n",
                 (val & WM8903_CHIP_REV_MASK) + 'A');

        /* Reset the device */
        regmap_write(wm8903->regmap, WM8903_SW_RESET_AND_ID, 0x8903);

        wm8903_init_gpio(wm8903);

        /* Set up GPIO pin state, detect if any are MIC detect outputs */
        for (i = 0; i < ARRAY_SIZE(pdata->gpio_cfg); i++) {
                if ((!pdata->gpio_cfg[i]) ||
                    (pdata->gpio_cfg[i] > WM8903_GPIO_CONFIG_ZERO))
                        continue;

                regmap_write(wm8903->regmap, WM8903_GPIO_CONTROL_1 + i,
                                pdata->gpio_cfg[i] & 0x7fff);

                val = (pdata->gpio_cfg[i] & WM8903_GP1_FN_MASK)
                        >> WM8903_GP1_FN_SHIFT;

                switch (val) {
                case WM8903_GPn_FN_MICBIAS_CURRENT_DETECT:
                case WM8903_GPn_FN_MICBIAS_SHORT_DETECT:
                        mic_gpio = true;
                        break;
                default:
                        break;
                }
        }

        /* Set up microphone detection */
        regmap_write(wm8903->regmap, WM8903_MIC_BIAS_CONTROL_0,
                     pdata->micdet_cfg);

        /* Microphone detection needs the WSEQ clock */
        if (pdata->micdet_cfg)
                regmap_update_bits(wm8903->regmap, WM8903_WRITE_SEQUENCER_0,
                                   WM8903_WSEQ_ENA, WM8903_WSEQ_ENA);

        /* If microphone detection is enabled by pdata but
         * detected via IRQ then interrupts can be lost before
         * the machine driver has set up microphone detection
         * IRQs as the IRQs are clear on read.  The detection
         * will be enabled when the machine driver configures.
         */
        WARN_ON(!mic_gpio && (pdata->micdet_cfg & WM8903_MICDET_ENA));

        wm8903->mic_delay = pdata->micdet_delay;

        if (i2c->irq) {
                if (pdata->irq_active_low) {
                        trigger = IRQF_TRIGGER_LOW;
                        irq_pol = WM8903_IRQ_POL;
                } else {
                        trigger = IRQF_TRIGGER_HIGH;
                        irq_pol = 0;
                }

                regmap_update_bits(wm8903->regmap, WM8903_INTERRUPT_CONTROL,
                                   WM8903_IRQ_POL, irq_pol);

                ret = request_threaded_irq(i2c->irq, NULL, wm8903_irq,
                                           trigger | IRQF_ONESHOT,
                                           "wm8903", wm8903);
                if (ret != 0) {
                        dev_err(wm8903->dev, "Failed to request IRQ: %d\n",
                                ret);
                        return ret;
                }

                /* Enable write sequencer interrupts */
                regmap_update_bits(wm8903->regmap,
                                   WM8903_INTERRUPT_STATUS_1_MASK,
                                   WM8903_IM_WSEQ_BUSY_EINT, 0);
        }

        /* Latch volume update bits */
        regmap_update_bits(wm8903->regmap, WM8903_ADC_DIGITAL_VOLUME_LEFT,
                           WM8903_ADCVU, WM8903_ADCVU);
        regmap_update_bits(wm8903->regmap, WM8903_ADC_DIGITAL_VOLUME_RIGHT,
                           WM8903_ADCVU, WM8903_ADCVU);

        regmap_update_bits(wm8903->regmap, WM8903_DAC_DIGITAL_VOLUME_LEFT,
                           WM8903_DACVU, WM8903_DACVU);
        regmap_update_bits(wm8903->regmap, WM8903_DAC_DIGITAL_VOLUME_RIGHT,
                           WM8903_DACVU, WM8903_DACVU);

        regmap_update_bits(wm8903->regmap, WM8903_ANALOGUE_OUT1_LEFT,
                           WM8903_HPOUTVU, WM8903_HPOUTVU);
        regmap_update_bits(wm8903->regmap, WM8903_ANALOGUE_OUT1_RIGHT,
                           WM8903_HPOUTVU, WM8903_HPOUTVU);

        regmap_update_bits(wm8903->regmap, WM8903_ANALOGUE_OUT2_LEFT,
                           WM8903_LINEOUTVU, WM8903_LINEOUTVU);
        regmap_update_bits(wm8903->regmap, WM8903_ANALOGUE_OUT2_RIGHT,
                           WM8903_LINEOUTVU, WM8903_LINEOUTVU);

        regmap_update_bits(wm8903->regmap, WM8903_ANALOGUE_OUT3_LEFT,
                           WM8903_SPKVU, WM8903_SPKVU);
        regmap_update_bits(wm8903->regmap, WM8903_ANALOGUE_OUT3_RIGHT,
                           WM8903_SPKVU, WM8903_SPKVU);

        /* Enable DAC soft mute by default */
        regmap_update_bits(wm8903->regmap, WM8903_DAC_DIGITAL_1,
                           WM8903_DAC_MUTEMODE | WM8903_DAC_MUTE,
                           WM8903_DAC_MUTEMODE | WM8903_DAC_MUTE);

        ret = devm_snd_soc_register_component(&i2c->dev,
                        &soc_component_dev_wm8903, &wm8903_dai, 1);
        if (ret != 0)
                goto err;

        return 0;
err:
        regulator_bulk_disable(ARRAY_SIZE(wm8903->supplies),
                               wm8903->supplies);
        return ret;
}

static int wm8903_i2c_remove(struct i2c_client *client)
{
        struct wm8903_priv *wm8903 = i2c_get_clientdata(client);

        regulator_bulk_disable(ARRAY_SIZE(wm8903->supplies),
                               wm8903->supplies);
        if (client->irq)
                free_irq(client->irq, wm8903);
        wm8903_free_gpio(wm8903);

        return 0;
}

static const struct of_device_id wm8903_of_match[] = {
        { .compatible = "wlf,wm8903", },
        {},
};
MODULE_DEVICE_TABLE(of, wm8903_of_match);

static const struct i2c_device_id wm8903_i2c_id[] = {
        { "wm8903", 0 },
        { }
};
MODULE_DEVICE_TABLE(i2c, wm8903_i2c_id);

static struct i2c_driver wm8903_i2c_driver = {
        .driver = {
                .name = "wm8903",
                .of_match_table = wm8903_of_match,
        },
        .probe =    wm8903_i2c_probe,
        .remove =   wm8903_i2c_remove,
        .id_table = wm8903_i2c_id,
};

module_i2c_driver(wm8903_i2c_driver);

MODULE_DESCRIPTION("ASoC WM8903 driver");
MODULE_AUTHOR("Mark Brown <broonie@opensource.wolfsonmicro.cm>");
MODULE_LICENSE("GPL");