// SPDX-License-Identifier: GPL-2.0
/* Copyright(c) 2007 - 2018 Intel Corporation. */

/* e1000_82575
 * e1000_82576
 */

#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt

#include <linux/types.h>
#include <linux/if_ether.h>
#include <linux/i2c.h>

#include "e1000_mac.h"
#include "e1000_82575.h"
#include "e1000_i210.h"
#include "igb.h"

static s32  igb_get_invariants_82575(struct e1000_hw *);
static s32  igb_acquire_phy_82575(struct e1000_hw *);
static void igb_release_phy_82575(struct e1000_hw *);
static s32  igb_acquire_nvm_82575(struct e1000_hw *);
static void igb_release_nvm_82575(struct e1000_hw *);
static s32  igb_check_for_link_82575(struct e1000_hw *);
static s32  igb_get_cfg_done_82575(struct e1000_hw *);
static s32  igb_init_hw_82575(struct e1000_hw *);
static s32  igb_phy_hw_reset_sgmii_82575(struct e1000_hw *);
static s32  igb_read_phy_reg_sgmii_82575(struct e1000_hw *, u32, u16 *);
static s32  igb_reset_hw_82575(struct e1000_hw *);
static s32  igb_reset_hw_82580(struct e1000_hw *);
static s32  igb_set_d0_lplu_state_82575(struct e1000_hw *, bool);
static s32  igb_set_d0_lplu_state_82580(struct e1000_hw *, bool);
static s32  igb_set_d3_lplu_state_82580(struct e1000_hw *, bool);
static s32  igb_setup_copper_link_82575(struct e1000_hw *);
static s32  igb_setup_serdes_link_82575(struct e1000_hw *);
static s32  igb_write_phy_reg_sgmii_82575(struct e1000_hw *, u32, u16);
static void igb_clear_hw_cntrs_82575(struct e1000_hw *);
static s32  igb_acquire_swfw_sync_82575(struct e1000_hw *, u16);
static s32  igb_get_pcs_speed_and_duplex_82575(struct e1000_hw *, u16 *,
                                                 u16 *);
static s32  igb_get_phy_id_82575(struct e1000_hw *);
static void igb_release_swfw_sync_82575(struct e1000_hw *, u16);
static bool igb_sgmii_active_82575(struct e1000_hw *);
static s32  igb_reset_init_script_82575(struct e1000_hw *);
static s32  igb_read_mac_addr_82575(struct e1000_hw *);
static s32  igb_set_pcie_completion_timeout(struct e1000_hw *hw);
static s32  igb_reset_mdicnfg_82580(struct e1000_hw *hw);
static s32  igb_validate_nvm_checksum_82580(struct e1000_hw *hw);
static s32  igb_update_nvm_checksum_82580(struct e1000_hw *hw);
static s32 igb_validate_nvm_checksum_i350(struct e1000_hw *hw);
static s32 igb_update_nvm_checksum_i350(struct e1000_hw *hw);
static const u16 e1000_82580_rxpbs_table[] = {
        36, 72, 144, 1, 2, 4, 8, 16, 35, 70, 140 };

/* Due to a hw errata, if the host tries to  configure the VFTA register
 * while performing queries from the BMC or DMA, then the VFTA in some
 * cases won't be written.
 */

/**
 *  igb_write_vfta_i350 - Write value to VLAN filter table
 *  @hw: pointer to the HW structure
 *  @offset: register offset in VLAN filter table
 *  @value: register value written to VLAN filter table
 *
 *  Writes value at the given offset in the register array which stores
 *  the VLAN filter table.
 **/
static void igb_write_vfta_i350(struct e1000_hw *hw, u32 offset, u32 value)
{
        struct igb_adapter *adapter = hw->back;
        int i;

        for (i = 10; i--;)
                array_wr32(E1000_VFTA, offset, value);

        wrfl();
        adapter->shadow_vfta[offset] = value;
}

/**
 *  igb_sgmii_uses_mdio_82575 - Determine if I2C pins are for external MDIO
 *  @hw: pointer to the HW structure
 *
 *  Called to determine if the I2C pins are being used for I2C or as an
 *  external MDIO interface since the two options are mutually exclusive.
 **/
static bool igb_sgmii_uses_mdio_82575(struct e1000_hw *hw)
{
        u32 reg = 0;
        bool ext_mdio = false;

        switch (hw->mac.type) {
        case e1000_82575:
        case e1000_82576:
                reg = rd32(E1000_MDIC);
                ext_mdio = !!(reg & E1000_MDIC_DEST);
                break;
        case e1000_82580:
        case e1000_i350:
        case e1000_i354:
        case e1000_i210:
        case e1000_i211:
                reg = rd32(E1000_MDICNFG);
                ext_mdio = !!(reg & E1000_MDICNFG_EXT_MDIO);
                break;
        default:
                break;
        }
        return ext_mdio;
}

/**
 *  igb_check_for_link_media_swap - Check which M88E1112 interface linked
 *  @hw: pointer to the HW structure
 *
 *  Poll the M88E1112 interfaces to see which interface achieved link.
 */
static s32 igb_check_for_link_media_swap(struct e1000_hw *hw)
{
        struct e1000_phy_info *phy = &hw->phy;
        s32 ret_val;
        u16 data;
        u8 port = 0;

        /* Check the copper medium. */
        ret_val = phy->ops.write_reg(hw, E1000_M88E1112_PAGE_ADDR, 0);
        if (ret_val)
                return ret_val;

        ret_val = phy->ops.read_reg(hw, E1000_M88E1112_STATUS, &data);
        if (ret_val)
                return ret_val;

        if (data & E1000_M88E1112_STATUS_LINK)
                port = E1000_MEDIA_PORT_COPPER;

        /* Check the other medium. */
        ret_val = phy->ops.write_reg(hw, E1000_M88E1112_PAGE_ADDR, 1);
        if (ret_val)
                return ret_val;

        ret_val = phy->ops.read_reg(hw, E1000_M88E1112_STATUS, &data);
        if (ret_val)
                return ret_val;


        if (data & E1000_M88E1112_STATUS_LINK)
                port = E1000_MEDIA_PORT_OTHER;

        /* Determine if a swap needs to happen. */
        if (port && (hw->dev_spec._82575.media_port != port)) {
                hw->dev_spec._82575.media_port = port;
                hw->dev_spec._82575.media_changed = true;
        }

        if (port == E1000_MEDIA_PORT_COPPER) {
                /* reset page to 0 */
                ret_val = phy->ops.write_reg(hw, E1000_M88E1112_PAGE_ADDR, 0);
                if (ret_val)
                        return ret_val;
                igb_check_for_link_82575(hw);
        } else {
                igb_check_for_link_82575(hw);
                /* reset page to 0 */
                ret_val = phy->ops.write_reg(hw, E1000_M88E1112_PAGE_ADDR, 0);
                if (ret_val)
                        return ret_val;
        }

        return 0;
}

/**
 *  igb_init_phy_params_82575 - Init PHY func ptrs.
 *  @hw: pointer to the HW structure
 **/
static s32 igb_init_phy_params_82575(struct e1000_hw *hw)
{
        struct e1000_phy_info *phy = &hw->phy;
        s32 ret_val = 0;
        u32 ctrl_ext;

        if (hw->phy.media_type != e1000_media_type_copper) {
                phy->type = e1000_phy_none;
                goto out;
        }

        phy->autoneg_mask       = AUTONEG_ADVERTISE_SPEED_DEFAULT;
        phy->reset_delay_us     = 100;

        ctrl_ext = rd32(E1000_CTRL_EXT);

        if (igb_sgmii_active_82575(hw)) {
                phy->ops.reset = igb_phy_hw_reset_sgmii_82575;
                ctrl_ext |= E1000_CTRL_I2C_ENA;
        } else {
                phy->ops.reset = igb_phy_hw_reset;
                ctrl_ext &= ~E1000_CTRL_I2C_ENA;
        }

        wr32(E1000_CTRL_EXT, ctrl_ext);
        igb_reset_mdicnfg_82580(hw);

        if (igb_sgmii_active_82575(hw) && !igb_sgmii_uses_mdio_82575(hw)) {
                phy->ops.read_reg = igb_read_phy_reg_sgmii_82575;
                phy->ops.write_reg = igb_write_phy_reg_sgmii_82575;
        } else {
                switch (hw->mac.type) {
                case e1000_82580:
                case e1000_i350:
                case e1000_i354:
                case e1000_i210:
                case e1000_i211:
                        phy->ops.read_reg = igb_read_phy_reg_82580;
                        phy->ops.write_reg = igb_write_phy_reg_82580;
                        break;
                default:
                        phy->ops.read_reg = igb_read_phy_reg_igp;
                        phy->ops.write_reg = igb_write_phy_reg_igp;
                }
        }

        /* set lan id */
        hw->bus.func = (rd32(E1000_STATUS) & E1000_STATUS_FUNC_MASK) >>
                        E1000_STATUS_FUNC_SHIFT;

        /* Set phy->phy_addr and phy->id. */
        ret_val = igb_get_phy_id_82575(hw);
        if (ret_val)
                return ret_val;

        /* Verify phy id and set remaining function pointers */
        switch (phy->id) {
        case M88E1543_E_PHY_ID:
        case M88E1512_E_PHY_ID:
        case I347AT4_E_PHY_ID:
        case M88E1112_E_PHY_ID:
        case M88E1111_I_PHY_ID:
                phy->type               = e1000_phy_m88;
                phy->ops.check_polarity = igb_check_polarity_m88;
                phy->ops.get_phy_info   = igb_get_phy_info_m88;
                if (phy->id != M88E1111_I_PHY_ID)
                        phy->ops.get_cable_length =
                                         igb_get_cable_length_m88_gen2;
                else
                        phy->ops.get_cable_length = igb_get_cable_length_m88;
                phy->ops.force_speed_duplex = igb_phy_force_speed_duplex_m88;
                /* Check if this PHY is configured for media swap. */
                if (phy->id == M88E1112_E_PHY_ID) {
                        u16 data;

                        ret_val = phy->ops.write_reg(hw,
                                                     E1000_M88E1112_PAGE_ADDR,
                                                     2);
                        if (ret_val)
                                goto out;

                        ret_val = phy->ops.read_reg(hw,
                                                    E1000_M88E1112_MAC_CTRL_1,
                                                    &data);
                        if (ret_val)
                                goto out;

                        data = (data & E1000_M88E1112_MAC_CTRL_1_MODE_MASK) >>
                               E1000_M88E1112_MAC_CTRL_1_MODE_SHIFT;
                        if (data == E1000_M88E1112_AUTO_COPPER_SGMII ||
                            data == E1000_M88E1112_AUTO_COPPER_BASEX)
                                hw->mac.ops.check_for_link =
                                                igb_check_for_link_media_swap;
                }
                if (phy->id == M88E1512_E_PHY_ID) {
                        ret_val = igb_initialize_M88E1512_phy(hw);
                        if (ret_val)
                                goto out;
                }
                if (phy->id == M88E1543_E_PHY_ID) {
                        ret_val = igb_initialize_M88E1543_phy(hw);
                        if (ret_val)
                                goto out;
                }
                break;
        case IGP03E1000_E_PHY_ID:
                phy->type = e1000_phy_igp_3;
                phy->ops.get_phy_info = igb_get_phy_info_igp;
                phy->ops.get_cable_length = igb_get_cable_length_igp_2;
                phy->ops.force_speed_duplex = igb_phy_force_speed_duplex_igp;
                phy->ops.set_d0_lplu_state = igb_set_d0_lplu_state_82575;
                phy->ops.set_d3_lplu_state = igb_set_d3_lplu_state;
                break;
        case I82580_I_PHY_ID:
        case I350_I_PHY_ID:
                phy->type = e1000_phy_82580;
                phy->ops.force_speed_duplex =
                                         igb_phy_force_speed_duplex_82580;
                phy->ops.get_cable_length = igb_get_cable_length_82580;
                phy->ops.get_phy_info = igb_get_phy_info_82580;
                phy->ops.set_d0_lplu_state = igb_set_d0_lplu_state_82580;
                phy->ops.set_d3_lplu_state = igb_set_d3_lplu_state_82580;
                break;
        case I210_I_PHY_ID:
                phy->type               = e1000_phy_i210;
                phy->ops.check_polarity = igb_check_polarity_m88;
                phy->ops.get_cfg_done   = igb_get_cfg_done_i210;
                phy->ops.get_phy_info   = igb_get_phy_info_m88;
                phy->ops.get_cable_length = igb_get_cable_length_m88_gen2;
                phy->ops.set_d0_lplu_state = igb_set_d0_lplu_state_82580;
                phy->ops.set_d3_lplu_state = igb_set_d3_lplu_state_82580;
                phy->ops.force_speed_duplex = igb_phy_force_speed_duplex_m88;
                break;
        case BCM54616_E_PHY_ID:
                phy->type = e1000_phy_bcm54616;
                break;
        default:
                ret_val = -E1000_ERR_PHY;
                goto out;
        }

out:
        return ret_val;
}

/**
 *  igb_init_nvm_params_82575 - Init NVM func ptrs.
 *  @hw: pointer to the HW structure
 **/
static s32 igb_init_nvm_params_82575(struct e1000_hw *hw)
{
        struct e1000_nvm_info *nvm = &hw->nvm;
        u32 eecd = rd32(E1000_EECD);
        u16 size;

        size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >>
                     E1000_EECD_SIZE_EX_SHIFT);

        /* Added to a constant, "size" becomes the left-shift value
         * for setting word_size.
         */
        size += NVM_WORD_SIZE_BASE_SHIFT;

        /* Just in case size is out of range, cap it to the largest
         * EEPROM size supported
         */
        if (size > 15)
                size = 15;

        nvm->word_size = BIT(size);
        nvm->opcode_bits = 8;
        nvm->delay_usec = 1;

        switch (nvm->override) {
        case e1000_nvm_override_spi_large:
                nvm->page_size = 32;
                nvm->address_bits = 16;
                break;
        case e1000_nvm_override_spi_small:
                nvm->page_size = 8;
                nvm->address_bits = 8;
                break;
        default:
                nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8;
                nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ?
                                    16 : 8;
                break;
        }
        if (nvm->word_size == BIT(15))
                nvm->page_size = 128;

        nvm->type = e1000_nvm_eeprom_spi;

        /* NVM Function Pointers */
        nvm->ops.acquire = igb_acquire_nvm_82575;
        nvm->ops.release = igb_release_nvm_82575;
        nvm->ops.write = igb_write_nvm_spi;
        nvm->ops.validate = igb_validate_nvm_checksum;
        nvm->ops.update = igb_update_nvm_checksum;
        if (nvm->word_size < BIT(15))
                nvm->ops.read = igb_read_nvm_eerd;
        else
                nvm->ops.read = igb_read_nvm_spi;

        /* override generic family function pointers for specific descendants */
        switch (hw->mac.type) {
        case e1000_82580:
                nvm->ops.validate = igb_validate_nvm_checksum_82580;
                nvm->ops.update = igb_update_nvm_checksum_82580;
                break;
        case e1000_i354:
        case e1000_i350:
                nvm->ops.validate = igb_validate_nvm_checksum_i350;
                nvm->ops.update = igb_update_nvm_checksum_i350;
                break;
        default:
                break;
        }

        return 0;
}

/**
 *  igb_init_mac_params_82575 - Init MAC func ptrs.
 *  @hw: pointer to the HW structure
 **/
static s32 igb_init_mac_params_82575(struct e1000_hw *hw)
{
        struct e1000_mac_info *mac = &hw->mac;
        struct e1000_dev_spec_82575 *dev_spec = &hw->dev_spec._82575;

        /* Set mta register count */
        mac->mta_reg_count = 128;
        /* Set uta register count */
        mac->uta_reg_count = (hw->mac.type == e1000_82575) ? 0 : 128;
        /* Set rar entry count */
        switch (mac->type) {
        case e1000_82576:
                mac->rar_entry_count = E1000_RAR_ENTRIES_82576;
                break;
        case e1000_82580:
                mac->rar_entry_count = E1000_RAR_ENTRIES_82580;
                break;
        case e1000_i350:
        case e1000_i354:
                mac->rar_entry_count = E1000_RAR_ENTRIES_I350;
                break;
        default:
                mac->rar_entry_count = E1000_RAR_ENTRIES_82575;
                break;
        }
        /* reset */
        if (mac->type >= e1000_82580)
                mac->ops.reset_hw = igb_reset_hw_82580;
        else
                mac->ops.reset_hw = igb_reset_hw_82575;

        if (mac->type >= e1000_i210) {
                mac->ops.acquire_swfw_sync = igb_acquire_swfw_sync_i210;
                mac->ops.release_swfw_sync = igb_release_swfw_sync_i210;

        } else {
                mac->ops.acquire_swfw_sync = igb_acquire_swfw_sync_82575;
                mac->ops.release_swfw_sync = igb_release_swfw_sync_82575;
        }

        if ((hw->mac.type == e1000_i350) || (hw->mac.type == e1000_i354))
                mac->ops.write_vfta = igb_write_vfta_i350;
        else
                mac->ops.write_vfta = igb_write_vfta;

        /* Set if part includes ASF firmware */
        mac->asf_firmware_present = true;
        /* Set if manageability features are enabled. */
        mac->arc_subsystem_valid =
                (rd32(E1000_FWSM) & E1000_FWSM_MODE_MASK)
                        ? true : false;
        /* enable EEE on i350 parts and later parts */
        if (mac->type >= e1000_i350)
                dev_spec->eee_disable = false;
        else
                dev_spec->eee_disable = true;
        /* Allow a single clear of the SW semaphore on I210 and newer */
        if (mac->type >= e1000_i210)
                dev_spec->clear_semaphore_once = true;
        /* physical interface link setup */
        mac->ops.setup_physical_interface =
                (hw->phy.media_type == e1000_media_type_copper)
                        ? igb_setup_copper_link_82575
                        : igb_setup_serdes_link_82575;

        if (mac->type == e1000_82580 || mac->type == e1000_i350) {
                switch (hw->device_id) {
                /* feature not supported on these id's */
                case E1000_DEV_ID_DH89XXCC_SGMII:
                case E1000_DEV_ID_DH89XXCC_SERDES:
                case E1000_DEV_ID_DH89XXCC_BACKPLANE:
                case E1000_DEV_ID_DH89XXCC_SFP:
                        break;
                default:
                        hw->dev_spec._82575.mas_capable = true;
                        break;
                }
        }
        return 0;
}

/**
 *  igb_set_sfp_media_type_82575 - derives SFP module media type.
 *  @hw: pointer to the HW structure
 *
 *  The media type is chosen based on SFP module.
 *  compatibility flags retrieved from SFP ID EEPROM.
 **/
static s32 igb_set_sfp_media_type_82575(struct e1000_hw *hw)
{
        s32 ret_val = E1000_ERR_CONFIG;
        u32 ctrl_ext = 0;
        struct e1000_dev_spec_82575 *dev_spec = &hw->dev_spec._82575;
        struct e1000_sfp_flags *eth_flags = &dev_spec->eth_flags;
        u8 tranceiver_type = 0;
        s32 timeout = 3;

        /* Turn I2C interface ON and power on sfp cage */
        ctrl_ext = rd32(E1000_CTRL_EXT);
        ctrl_ext &= ~E1000_CTRL_EXT_SDP3_DATA;
        wr32(E1000_CTRL_EXT, ctrl_ext | E1000_CTRL_I2C_ENA);

        wrfl();

        /* Read SFP module data */
        while (timeout) {
                ret_val = igb_read_sfp_data_byte(hw,
                        E1000_I2CCMD_SFP_DATA_ADDR(E1000_SFF_IDENTIFIER_OFFSET),
                        &tranceiver_type);
                if (ret_val == 0)
                        break;
                msleep(100);
                timeout--;
        }
        if (ret_val != 0)
                goto out;

        ret_val = igb_read_sfp_data_byte(hw,
                        E1000_I2CCMD_SFP_DATA_ADDR(E1000_SFF_ETH_FLAGS_OFFSET),
                        (u8 *)eth_flags);
        if (ret_val != 0)
                goto out;

        /* Check if there is some SFP module plugged and powered */
        if ((tranceiver_type == E1000_SFF_IDENTIFIER_SFP) ||
            (tranceiver_type == E1000_SFF_IDENTIFIER_SFF)) {
                dev_spec->module_plugged = true;
                if (eth_flags->e1000_base_lx || eth_flags->e1000_base_sx) {
                        hw->phy.media_type = e1000_media_type_internal_serdes;
                } else if (eth_flags->e100_base_fx) {
                        dev_spec->sgmii_active = true;
                        hw->phy.media_type = e1000_media_type_internal_serdes;
                } else if (eth_flags->e1000_base_t) {
                        dev_spec->sgmii_active = true;
                        hw->phy.media_type = e1000_media_type_copper;
                } else {
                        hw->phy.media_type = e1000_media_type_unknown;
                        hw_dbg("PHY module has not been recognized\n");
                        goto out;
                }
        } else {
                hw->phy.media_type = e1000_media_type_unknown;
        }
        ret_val = 0;
out:
        /* Restore I2C interface setting */
        wr32(E1000_CTRL_EXT, ctrl_ext);
        return ret_val;
}

static s32 igb_get_invariants_82575(struct e1000_hw *hw)
{
        struct e1000_mac_info *mac = &hw->mac;
        struct e1000_dev_spec_82575 *dev_spec = &hw->dev_spec._82575;
        s32 ret_val;
        u32 ctrl_ext = 0;
        u32 link_mode = 0;

        switch (hw->device_id) {
        case E1000_DEV_ID_82575EB_COPPER:
        case E1000_DEV_ID_82575EB_FIBER_SERDES:
        case E1000_DEV_ID_82575GB_QUAD_COPPER:
                mac->type = e1000_82575;
                break;
        case E1000_DEV_ID_82576:
        case E1000_DEV_ID_82576_NS:
        case E1000_DEV_ID_82576_NS_SERDES:
        case E1000_DEV_ID_82576_FIBER:
        case E1000_DEV_ID_82576_SERDES:
        case E1000_DEV_ID_82576_QUAD_COPPER:
        case E1000_DEV_ID_82576_QUAD_COPPER_ET2:
        case E1000_DEV_ID_82576_SERDES_QUAD:
                mac->type = e1000_82576;
                break;
        case E1000_DEV_ID_82580_COPPER:
        case E1000_DEV_ID_82580_FIBER:
        case E1000_DEV_ID_82580_QUAD_FIBER:
        case E1000_DEV_ID_82580_SERDES:
        case E1000_DEV_ID_82580_SGMII:
        case E1000_DEV_ID_82580_COPPER_DUAL:
        case E1000_DEV_ID_DH89XXCC_SGMII:
        case E1000_DEV_ID_DH89XXCC_SERDES:
        case E1000_DEV_ID_DH89XXCC_BACKPLANE:
        case E1000_DEV_ID_DH89XXCC_SFP:
                mac->type = e1000_82580;
                break;
        case E1000_DEV_ID_I350_COPPER:
        case E1000_DEV_ID_I350_FIBER:
        case E1000_DEV_ID_I350_SERDES:
        case E1000_DEV_ID_I350_SGMII:
                mac->type = e1000_i350;
                break;
        case E1000_DEV_ID_I210_COPPER:
        case E1000_DEV_ID_I210_FIBER:
        case E1000_DEV_ID_I210_SERDES:
        case E1000_DEV_ID_I210_SGMII:
        case E1000_DEV_ID_I210_COPPER_FLASHLESS:
        case E1000_DEV_ID_I210_SERDES_FLASHLESS:
                mac->type = e1000_i210;
                break;
        case E1000_DEV_ID_I211_COPPER:
                mac->type = e1000_i211;
                break;
        case E1000_DEV_ID_I354_BACKPLANE_1GBPS:
        case E1000_DEV_ID_I354_SGMII:
        case E1000_DEV_ID_I354_BACKPLANE_2_5GBPS:
                mac->type = e1000_i354;
                break;
        default:
                return -E1000_ERR_MAC_INIT;
        }

        /* Set media type */
        /* The 82575 uses bits 22:23 for link mode. The mode can be changed
         * based on the EEPROM. We cannot rely upon device ID. There
         * is no distinguishable difference between fiber and internal
         * SerDes mode on the 82575. There can be an external PHY attached
         * on the SGMII interface. For this, we'll set sgmii_active to true.
         */
        hw->phy.media_type = e1000_media_type_copper;
        dev_spec->sgmii_active = false;
        dev_spec->module_plugged = false;

        ctrl_ext = rd32(E1000_CTRL_EXT);

        link_mode = ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK;
        switch (link_mode) {
        case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX:
                hw->phy.media_type = e1000_media_type_internal_serdes;
                break;
        case E1000_CTRL_EXT_LINK_MODE_SGMII:
                /* Get phy control interface type set (MDIO vs. I2C)*/
                if (igb_sgmii_uses_mdio_82575(hw)) {
                        hw->phy.media_type = e1000_media_type_copper;
                        dev_spec->sgmii_active = true;
                        break;
                }
                /* fall through - for I2C based SGMII */
        case E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES:
                /* read media type from SFP EEPROM */
                ret_val = igb_set_sfp_media_type_82575(hw);
                if ((ret_val != 0) ||
                    (hw->phy.media_type == e1000_media_type_unknown)) {
                        /* If media type was not identified then return media
                         * type defined by the CTRL_EXT settings.
                         */
                        hw->phy.media_type = e1000_media_type_internal_serdes;

                        if (link_mode == E1000_CTRL_EXT_LINK_MODE_SGMII) {
                                hw->phy.media_type = e1000_media_type_copper;
                                dev_spec->sgmii_active = true;
                        }

                        break;
                }

                /* do not change link mode for 100BaseFX */
                if (dev_spec->eth_flags.e100_base_fx)
                        break;

                /* change current link mode setting */
                ctrl_ext &= ~E1000_CTRL_EXT_LINK_MODE_MASK;

                if (hw->phy.media_type == e1000_media_type_copper)
                        ctrl_ext |= E1000_CTRL_EXT_LINK_MODE_SGMII;
                else
                        ctrl_ext |= E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES;

                wr32(E1000_CTRL_EXT, ctrl_ext);

                break;
        default:
                break;
        }

        /* mac initialization and operations */
        ret_val = igb_init_mac_params_82575(hw);
        if (ret_val)
                goto out;

        /* NVM initialization */
        ret_val = igb_init_nvm_params_82575(hw);
        switch (hw->mac.type) {
        case e1000_i210:
        case e1000_i211:
                ret_val = igb_init_nvm_params_i210(hw);
                break;
        default:
                break;
        }

        if (ret_val)
                goto out;

        /* if part supports SR-IOV then initialize mailbox parameters */
        switch (mac->type) {
        case e1000_82576:
        case e1000_i350:
                igb_init_mbx_params_pf(hw);
                break;
        default:
                break;
        }

        /* setup PHY parameters */
        ret_val = igb_init_phy_params_82575(hw);

out:
        return ret_val;
}

/**
 *  igb_acquire_phy_82575 - Acquire rights to access PHY
 *  @hw: pointer to the HW structure
 *
 *  Acquire access rights to the correct PHY.  This is a
 *  function pointer entry point called by the api module.
 **/
static s32 igb_acquire_phy_82575(struct e1000_hw *hw)
{
        u16 mask = E1000_SWFW_PHY0_SM;

        if (hw->bus.func == E1000_FUNC_1)
                mask = E1000_SWFW_PHY1_SM;
        else if (hw->bus.func == E1000_FUNC_2)
                mask = E1000_SWFW_PHY2_SM;
        else if (hw->bus.func == E1000_FUNC_3)
                mask = E1000_SWFW_PHY3_SM;

        return hw->mac.ops.acquire_swfw_sync(hw, mask);
}

/**
 *  igb_release_phy_82575 - Release rights to access PHY
 *  @hw: pointer to the HW structure
 *
 *  A wrapper to release access rights to the correct PHY.  This is a
 *  function pointer entry point called by the api module.
 **/
static void igb_release_phy_82575(struct e1000_hw *hw)
{
        u16 mask = E1000_SWFW_PHY0_SM;

        if (hw->bus.func == E1000_FUNC_1)
                mask = E1000_SWFW_PHY1_SM;
        else if (hw->bus.func == E1000_FUNC_2)
                mask = E1000_SWFW_PHY2_SM;
        else if (hw->bus.func == E1000_FUNC_3)
                mask = E1000_SWFW_PHY3_SM;

        hw->mac.ops.release_swfw_sync(hw, mask);
}

/**
 *  igb_read_phy_reg_sgmii_82575 - Read PHY register using sgmii
 *  @hw: pointer to the HW structure
 *  @offset: register offset to be read
 *  @data: pointer to the read data
 *
 *  Reads the PHY register at offset using the serial gigabit media independent
 *  interface and stores the retrieved information in data.
 **/
static s32 igb_read_phy_reg_sgmii_82575(struct e1000_hw *hw, u32 offset,
                                          u16 *data)
{
        s32 ret_val = -E1000_ERR_PARAM;

        if (offset > E1000_MAX_SGMII_PHY_REG_ADDR) {
                hw_dbg("PHY Address %u is out of range\n", offset);
                goto out;
        }

        ret_val = hw->phy.ops.acquire(hw);
        if (ret_val)
                goto out;

        ret_val = igb_read_phy_reg_i2c(hw, offset, data);

        hw->phy.ops.release(hw);

out:
        return ret_val;
}

/**
 *  igb_write_phy_reg_sgmii_82575 - Write PHY register using sgmii
 *  @hw: pointer to the HW structure
 *  @offset: register offset to write to
 *  @data: data to write at register offset
 *
 *  Writes the data to PHY register at the offset using the serial gigabit
 *  media independent interface.
 **/
static s32 igb_write_phy_reg_sgmii_82575(struct e1000_hw *hw, u32 offset,
                                           u16 data)
{
        s32 ret_val = -E1000_ERR_PARAM;


        if (offset > E1000_MAX_SGMII_PHY_REG_ADDR) {
                hw_dbg("PHY Address %d is out of range\n", offset);
                goto out;
        }

        ret_val = hw->phy.ops.acquire(hw);
        if (ret_val)
                goto out;

        ret_val = igb_write_phy_reg_i2c(hw, offset, data);

        hw->phy.ops.release(hw);

out:
        return ret_val;
}

/**
 *  igb_get_phy_id_82575 - Retrieve PHY addr and id
 *  @hw: pointer to the HW structure
 *
 *  Retrieves the PHY address and ID for both PHY's which do and do not use
 *  sgmi interface.
 **/
static s32 igb_get_phy_id_82575(struct e1000_hw *hw)
{
        struct e1000_phy_info *phy = &hw->phy;
        s32  ret_val = 0;
        u16 phy_id;
        u32 ctrl_ext;
        u32 mdic;

        /* Extra read required for some PHY's on i354 */
        if (hw->mac.type == e1000_i354)
                igb_get_phy_id(hw);

        /* For SGMII PHYs, we try the list of possible addresses until
         * we find one that works.  For non-SGMII PHYs
         * (e.g. integrated copper PHYs), an address of 1 should
         * work.  The result of this function should mean phy->phy_addr
         * and phy->id are set correctly.
         */
        if (!(igb_sgmii_active_82575(hw))) {
                phy->addr = 1;
                ret_val = igb_get_phy_id(hw);
                goto out;
        }

        if (igb_sgmii_uses_mdio_82575(hw)) {
                switch (hw->mac.type) {
                case e1000_82575:
                case e1000_82576:
                        mdic = rd32(E1000_MDIC);
                        mdic &= E1000_MDIC_PHY_MASK;
                        phy->addr = mdic >> E1000_MDIC_PHY_SHIFT;
                        break;
                case e1000_82580:
                case e1000_i350:
                case e1000_i354:
                case e1000_i210:
                case e1000_i211:
                        mdic = rd32(E1000_MDICNFG);
                        mdic &= E1000_MDICNFG_PHY_MASK;
                        phy->addr = mdic >> E1000_MDICNFG_PHY_SHIFT;
                        break;
                default:
                        ret_val = -E1000_ERR_PHY;
                        goto out;
                }
                ret_val = igb_get_phy_id(hw);
                goto out;
        }

        /* Power on sgmii phy if it is disabled */
        ctrl_ext = rd32(E1000_CTRL_EXT);
        wr32(E1000_CTRL_EXT, ctrl_ext & ~E1000_CTRL_EXT_SDP3_DATA);
        wrfl();
        msleep(300);

        /* The address field in the I2CCMD register is 3 bits and 0 is invalid.
         * Therefore, we need to test 1-7
         */
        for (phy->addr = 1; phy->addr < 8; phy->addr++) {
                ret_val = igb_read_phy_reg_sgmii_82575(hw, PHY_ID1, &phy_id);
                if (ret_val == 0) {
                        hw_dbg("Vendor ID 0x%08X read at address %u\n",
                               phy_id, phy->addr);
                        /* At the time of this writing, The M88 part is
                         * the only supported SGMII PHY product.
                         */
                        if (phy_id == M88_VENDOR)
                                break;
                } else {
                        hw_dbg("PHY address %u was unreadable\n", phy->addr);
                }
        }

        /* A valid PHY type couldn't be found. */
        if (phy->addr == 8) {
                phy->addr = 0;
                ret_val = -E1000_ERR_PHY;
                goto out;
        } else {
                ret_val = igb_get_phy_id(hw);
        }

        /* restore previous sfp cage power state */
        wr32(E1000_CTRL_EXT, ctrl_ext);

out:
        return ret_val;
}

/**
 *  igb_phy_hw_reset_sgmii_82575 - Performs a PHY reset
 *  @hw: pointer to the HW structure
 *
 *  Resets the PHY using the serial gigabit media independent interface.
 **/
static s32 igb_phy_hw_reset_sgmii_82575(struct e1000_hw *hw)
{
        struct e1000_phy_info *phy = &hw->phy;
        s32 ret_val;

        /* This isn't a true "hard" reset, but is the only reset
         * available to us at this time.
         */

        hw_dbg("Soft resetting SGMII attached PHY...\n");

        /* SFP documentation requires the following to configure the SPF module
         * to work on SGMII.  No further documentation is given.
         */
        ret_val = hw->phy.ops.write_reg(hw, 0x1B, 0x8084);
        if (ret_val)
                goto out;

        ret_val = igb_phy_sw_reset(hw);
        if (ret_val)
                goto out;

        if (phy->id == M88E1512_E_PHY_ID)
                ret_val = igb_initialize_M88E1512_phy(hw);
        if (phy->id == M88E1543_E_PHY_ID)
                ret_val = igb_initialize_M88E1543_phy(hw);
out:
        return ret_val;
}

/**
 *  igb_set_d0_lplu_state_82575 - Set Low Power Linkup D0 state
 *  @hw: pointer to the HW structure
 *  @active: true to enable LPLU, false to disable
 *
 *  Sets the LPLU D0 state according to the active flag.  When
 *  activating LPLU this function also disables smart speed
 *  and vice versa.  LPLU will not be activated unless the
 *  device autonegotiation advertisement meets standards of
 *  either 10 or 10/100 or 10/100/1000 at all duplexes.
 *  This is a function pointer entry point only called by
 *  PHY setup routines.
 **/
static s32 igb_set_d0_lplu_state_82575(struct e1000_hw *hw, bool active)
{
        struct e1000_phy_info *phy = &hw->phy;
        s32 ret_val;
        u16 data;

        ret_val = phy->ops.read_reg(hw, IGP02E1000_PHY_POWER_MGMT, &data);
        if (ret_val)
                goto out;

        if (active) {
                data |= IGP02E1000_PM_D0_LPLU;
                ret_val = phy->ops.write_reg(hw, IGP02E1000_PHY_POWER_MGMT,
                                                 data);
                if (ret_val)
                        goto out;

                /* When LPLU is enabled, we should disable SmartSpeed */
                ret_val = phy->ops.read_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
                                                &data);
                data &= ~IGP01E1000_PSCFR_SMART_SPEED;
                ret_val = phy->ops.write_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
                                                 data);
                if (ret_val)
                        goto out;
        } else {
                data &= ~IGP02E1000_PM_D0_LPLU;
                ret_val = phy->ops.write_reg(hw, IGP02E1000_PHY_POWER_MGMT,
                                                 data);
                /* LPLU and SmartSpeed are mutually exclusive.  LPLU is used
                 * during Dx states where the power conservation is most
                 * important.  During driver activity we should enable
                 * SmartSpeed, so performance is maintained.
                 */
                if (phy->smart_speed == e1000_smart_speed_on) {
                        ret_val = phy->ops.read_reg(hw,

                                        IGP01E1000_PHY_PORT_CONFIG, &data);
                        if (ret_val)
                                goto out;

                        data |= IGP01E1000_PSCFR_SMART_SPEED;
                        ret_val = phy->ops.write_reg(hw,
                                        IGP01E1000_PHY_PORT_CONFIG, data);
                        if (ret_val)
                                goto out;
                } else if (phy->smart_speed == e1000_smart_speed_off) {
                        ret_val = phy->ops.read_reg(hw,
                                        IGP01E1000_PHY_PORT_CONFIG, &data);
                        if (ret_val)
                                goto out;

                        data &= ~IGP01E1000_PSCFR_SMART_SPEED;
                        ret_val = phy->ops.write_reg(hw,
                                        IGP01E1000_PHY_PORT_CONFIG, data);
                        if (ret_val)
                                goto out;
                }
        }

out:
        return ret_val;
}

/**
 *  igb_set_d0_lplu_state_82580 - Set Low Power Linkup D0 state
 *  @hw: pointer to the HW structure
 *  @active: true to enable LPLU, false to disable
 *
 *  Sets the LPLU D0 state according to the active flag.  When
 *  activating LPLU this function also disables smart speed
 *  and vice versa.  LPLU will not be activated unless the
 *  device autonegotiation advertisement meets standards of
 *  either 10 or 10/100 or 10/100/1000 at all duplexes.
 *  This is a function pointer entry point only called by
 *  PHY setup routines.
 **/
static s32 igb_set_d0_lplu_state_82580(struct e1000_hw *hw, bool active)
{
        struct e1000_phy_info *phy = &hw->phy;
        u16 data;

        data = rd32(E1000_82580_PHY_POWER_MGMT);

        if (active) {
                data |= E1000_82580_PM_D0_LPLU;

                /* When LPLU is enabled, we should disable SmartSpeed */
                data &= ~E1000_82580_PM_SPD;
        } else {
                data &= ~E1000_82580_PM_D0_LPLU;

                /* LPLU and SmartSpeed are mutually exclusive.  LPLU is used
                 * during Dx states where the power conservation is most
                 * important.  During driver activity we should enable
                 * SmartSpeed, so performance is maintained.
                 */
                if (phy->smart_speed == e1000_smart_speed_on)
                        data |= E1000_82580_PM_SPD;
                else if (phy->smart_speed == e1000_smart_speed_off)
                        data &= ~E1000_82580_PM_SPD; }

        wr32(E1000_82580_PHY_POWER_MGMT, data);
        return 0;
}

/**
 *  igb_set_d3_lplu_state_82580 - Sets low power link up state for D3
 *  @hw: pointer to the HW structure
 *  @active: boolean used to enable/disable lplu
 *
 *  Success returns 0, Failure returns 1
 *
 *  The low power link up (lplu) state is set to the power management level D3
 *  and SmartSpeed is disabled when active is true, else clear lplu for D3
 *  and enable Smartspeed.  LPLU and Smartspeed are mutually exclusive.  LPLU
 *  is used during Dx states where the power conservation is most important.
 *  During driver activity, SmartSpeed should be enabled so performance is
 *  maintained.
 **/
static s32 igb_set_d3_lplu_state_82580(struct e1000_hw *hw, bool active)
{
        struct e1000_phy_info *phy = &hw->phy;
        u16 data;

        data = rd32(E1000_82580_PHY_POWER_MGMT);

        if (!active) {
                data &= ~E1000_82580_PM_D3_LPLU;
                /* LPLU and SmartSpeed are mutually exclusive.  LPLU is used
                 * during Dx states where the power conservation is most
                 * important.  During driver activity we should enable
                 * SmartSpeed, so performance is maintained.
                 */
                if (phy->smart_speed == e1000_smart_speed_on)
                        data |= E1000_82580_PM_SPD;
                else if (phy->smart_speed == e1000_smart_speed_off)
                        data &= ~E1000_82580_PM_SPD;
        } else if ((phy->autoneg_advertised == E1000_ALL_SPEED_DUPLEX) ||
                   (phy->autoneg_advertised == E1000_ALL_NOT_GIG) ||
                   (phy->autoneg_advertised == E1000_ALL_10_SPEED)) {
                data |= E1000_82580_PM_D3_LPLU;
                /* When LPLU is enabled, we should disable SmartSpeed */
                data &= ~E1000_82580_PM_SPD;
        }

        wr32(E1000_82580_PHY_POWER_MGMT, data);
        return 0;
}

/**
 *  igb_acquire_nvm_82575 - Request for access to EEPROM
 *  @hw: pointer to the HW structure
 *
 *  Acquire the necessary semaphores for exclusive access to the EEPROM.
 *  Set the EEPROM access request bit and wait for EEPROM access grant bit.
 *  Return successful if access grant bit set, else clear the request for
 *  EEPROM access and return -E1000_ERR_NVM (-1).
 **/
static s32 igb_acquire_nvm_82575(struct e1000_hw *hw)
{
        s32 ret_val;

        ret_val = hw->mac.ops.acquire_swfw_sync(hw, E1000_SWFW_EEP_SM);
        if (ret_val)
                goto out;

        ret_val = igb_acquire_nvm(hw);

        if (ret_val)
                hw->mac.ops.release_swfw_sync(hw, E1000_SWFW_EEP_SM);

out:
        return ret_val;
}

/**
 *  igb_release_nvm_82575 - Release exclusive access to EEPROM
 *  @hw: pointer to the HW structure
 *
 *  Stop any current commands to the EEPROM and clear the EEPROM request bit,
 *  then release the semaphores acquired.
 **/
static void igb_release_nvm_82575(struct e1000_hw *hw)
{
        igb_release_nvm(hw);
        hw->mac.ops.release_swfw_sync(hw, E1000_SWFW_EEP_SM);
}

/**
 *  igb_acquire_swfw_sync_82575 - Acquire SW/FW semaphore
 *  @hw: pointer to the HW structure
 *  @mask: specifies which semaphore to acquire
 *
 *  Acquire the SW/FW semaphore to access the PHY or NVM.  The mask
 *  will also specify which port we're acquiring the lock for.
 **/
static s32 igb_acquire_swfw_sync_82575(struct e1000_hw *hw, u16 mask)
{
        u32 swfw_sync;
        u32 swmask = mask;
        u32 fwmask = mask << 16;
        s32 ret_val = 0;
        s32 i = 0, timeout = 200;

        while (i < timeout) {
                if (igb_get_hw_semaphore(hw)) {
                        ret_val = -E1000_ERR_SWFW_SYNC;
                        goto out;
                }

                swfw_sync = rd32(E1000_SW_FW_SYNC);
                if (!(swfw_sync & (fwmask | swmask)))
                        break;

                /* Firmware currently using resource (fwmask)
                 * or other software thread using resource (swmask)
                 */
                igb_put_hw_semaphore(hw);
                mdelay(5);
                i++;
        }

        if (i == timeout) {
                hw_dbg("Driver can't access resource, SW_FW_SYNC timeout.\n");
                ret_val = -E1000_ERR_SWFW_SYNC;
                goto out;
        }

        swfw_sync |= swmask;
        wr32(E1000_SW_FW_SYNC, swfw_sync);

        igb_put_hw_semaphore(hw);

out:
        return ret_val;
}

/**
 *  igb_release_swfw_sync_82575 - Release SW/FW semaphore
 *  @hw: pointer to the HW structure
 *  @mask: specifies which semaphore to acquire
 *
 *  Release the SW/FW semaphore used to access the PHY or NVM.  The mask
 *  will also specify which port we're releasing the lock for.
 **/
static void igb_release_swfw_sync_82575(struct e1000_hw *hw, u16 mask)
{
        u32 swfw_sync;

        while (igb_get_hw_semaphore(hw) != 0)
                ; /* Empty */

        swfw_sync = rd32(E1000_SW_FW_SYNC);
        swfw_sync &= ~mask;
        wr32(E1000_SW_FW_SYNC, swfw_sync);

        igb_put_hw_semaphore(hw);
}

/**
 *  igb_get_cfg_done_82575 - Read config done bit
 *  @hw: pointer to the HW structure
 *
 *  Read the management control register for the config done bit for
 *  completion status.  NOTE: silicon which is EEPROM-less will fail trying
 *  to read the config done bit, so an error is *ONLY* logged and returns
 *  0.  If we were to return with error, EEPROM-less silicon
 *  would not be able to be reset or change link.
 **/
static s32 igb_get_cfg_done_82575(struct e1000_hw *hw)
{
        s32 timeout = PHY_CFG_TIMEOUT;
        u32 mask = E1000_NVM_CFG_DONE_PORT_0;

        if (hw->bus.func == 1)
                mask = E1000_NVM_CFG_DONE_PORT_1;
        else if (hw->bus.func == E1000_FUNC_2)
                mask = E1000_NVM_CFG_DONE_PORT_2;
        else if (hw->bus.func == E1000_FUNC_3)
                mask = E1000_NVM_CFG_DONE_PORT_3;

        while (timeout) {
                if (rd32(E1000_EEMNGCTL) & mask)
                        break;
                usleep_range(1000, 2000);
                timeout--;
        }
        if (!timeout)
                hw_dbg("MNG configuration cycle has not completed.\n");

        /* If EEPROM is not marked present, init the PHY manually */
        if (((rd32(E1000_EECD) & E1000_EECD_PRES) == 0) &&
            (hw->phy.type == e1000_phy_igp_3))
                igb_phy_init_script_igp3(hw);

        return 0;
}

/**
 *  igb_get_link_up_info_82575 - Get link speed/duplex info
 *  @hw: pointer to the HW structure
 *  @speed: stores the current speed
 *  @duplex: stores the current duplex
 *
 *  This is a wrapper function, if using the serial gigabit media independent
 *  interface, use PCS to retrieve the link speed and duplex information.
 *  Otherwise, use the generic function to get the link speed and duplex info.
 **/
static s32 igb_get_link_up_info_82575(struct e1000_hw *hw, u16 *speed,
                                        u16 *duplex)
{
        s32 ret_val;

        if (hw->phy.media_type != e1000_media_type_copper)
                ret_val = igb_get_pcs_speed_and_duplex_82575(hw, speed,
                                                               duplex);
        else
                ret_val = igb_get_speed_and_duplex_copper(hw, speed,
                                                                    duplex);

        return ret_val;
}

/**
 *  igb_check_for_link_82575 - Check for link
 *  @hw: pointer to the HW structure
 *
 *  If sgmii is enabled, then use the pcs register to determine link, otherwise
 *  use the generic interface for determining link.
 **/
static s32 igb_check_for_link_82575(struct e1000_hw *hw)
{
        s32 ret_val;
        u16 speed, duplex;

        if (hw->phy.media_type != e1000_media_type_copper) {
                ret_val = igb_get_pcs_speed_and_duplex_82575(hw, &speed,
                                                             &duplex);
                /* Use this flag to determine if link needs to be checked or
                 * not.  If  we have link clear the flag so that we do not
                 * continue to check for link.
                 */
                hw->mac.get_link_status = !hw->mac.serdes_has_link;

                /* Configure Flow Control now that Auto-Neg has completed.
                 * First, we need to restore the desired flow control
                 * settings because we may have had to re-autoneg with a
                 * different link partner.
                 */
                ret_val = igb_config_fc_after_link_up(hw);
                if (ret_val)
                        hw_dbg("Error configuring flow control\n");
        } else {
                ret_val = igb_check_for_copper_link(hw);
        }

        return ret_val;
}

/**
 *  igb_power_up_serdes_link_82575 - Power up the serdes link after shutdown
 *  @hw: pointer to the HW structure
 **/
void igb_power_up_serdes_link_82575(struct e1000_hw *hw)
{
        u32 reg;


        if ((hw->phy.media_type != e1000_media_type_internal_serdes) &&
            !igb_sgmii_active_82575(hw))
                return;

        /* Enable PCS to turn on link */
        reg = rd32(E1000_PCS_CFG0);
        reg |= E1000_PCS_CFG_PCS_EN;
        wr32(E1000_PCS_CFG0, reg);

        /* Power up the laser */
        reg = rd32(E1000_CTRL_EXT);
        reg &= ~E1000_CTRL_EXT_SDP3_DATA;
        wr32(E1000_CTRL_EXT, reg);

        /* flush the write to verify completion */
        wrfl();
        usleep_range(1000, 2000);
}

/**
 *  igb_get_pcs_speed_and_duplex_82575 - Retrieve current speed/duplex
 *  @hw: pointer to the HW structure
 *  @speed: stores the current speed
 *  @duplex: stores the current duplex
 *
 *  Using the physical coding sub-layer (PCS), retrieve the current speed and
 *  duplex, then store the values in the pointers provided.
 **/
static s32 igb_get_pcs_speed_and_duplex_82575(struct e1000_hw *hw, u16 *speed,
                                                u16 *duplex)
{
        struct e1000_mac_info *mac = &hw->mac;
        u32 pcs, status;

        /* Set up defaults for the return values of this function */
        mac->serdes_has_link = false;
        *speed = 0;
        *duplex = 0;

        /* Read the PCS Status register for link state. For non-copper mode,
         * the status register is not accurate. The PCS status register is
         * used instead.
         */
        pcs = rd32(E1000_PCS_LSTAT);

        /* The link up bit determines when link is up on autoneg. The sync ok
         * gets set once both sides sync up and agree upon link. Stable link
         * can be determined by checking for both link up and link sync ok
         */
        if ((pcs & E1000_PCS_LSTS_LINK_OK) && (pcs & E1000_PCS_LSTS_SYNK_OK)) {
                mac->serdes_has_link = true;

                /* Detect and store PCS speed */
                if (pcs & E1000_PCS_LSTS_SPEED_1000)
                        *speed = SPEED_1000;
                else if (pcs & E1000_PCS_LSTS_SPEED_100)
                        *speed = SPEED_100;
                else
                        *speed = SPEED_10;

                /* Detect and store PCS duplex */
                if (pcs & E1000_PCS_LSTS_DUPLEX_FULL)
                        *duplex = FULL_DUPLEX;
                else
                        *duplex = HALF_DUPLEX;

        /* Check if it is an I354 2.5Gb backplane connection. */
                if (mac->type == e1000_i354) {
                        status = rd32(E1000_STATUS);
                        if ((status & E1000_STATUS_2P5_SKU) &&
                            !(status & E1000_STATUS_2P5_SKU_OVER)) {
                                *speed = SPEED_2500;
                                *duplex = FULL_DUPLEX;
                                hw_dbg("2500 Mbs, ");
                                hw_dbg("Full Duplex\n");
                        }
                }

        }

        return 0;
}

/**
 *  igb_shutdown_serdes_link_82575 - Remove link during power down
 *  @hw: pointer to the HW structure
 *
 *  In the case of fiber serdes, shut down optics and PCS on driver unload
 *  when management pass thru is not enabled.
 **/
void igb_shutdown_serdes_link_82575(struct e1000_hw *hw)
{
        u32 reg;

        if (hw->phy.media_type != e1000_media_type_internal_serdes &&
            igb_sgmii_active_82575(hw))
                return;

        if (!igb_enable_mng_pass_thru(hw)) {
                /* Disable PCS to turn off link */
                reg = rd32(E1000_PCS_CFG0);
                reg &= ~E1000_PCS_CFG_PCS_EN;
                wr32(E1000_PCS_CFG0, reg);

                /* shutdown the laser */
                reg = rd32(E1000_CTRL_EXT);
                reg |= E1000_CTRL_EXT_SDP3_DATA;
                wr32(E1000_CTRL_EXT, reg);

                /* flush the write to verify completion */
                wrfl();
                usleep_range(1000, 2000);
        }
}

/**
 *  igb_reset_hw_82575 - Reset hardware
 *  @hw: pointer to the HW structure
 *
 *  This resets the hardware into a known state.  This is a
 *  function pointer entry point called by the api module.
 **/
static s32 igb_reset_hw_82575(struct e1000_hw *hw)
{
        u32 ctrl;
        s32 ret_val;

        /* Prevent the PCI-E bus from sticking if there is no TLP connection
         * on the last TLP read/write transaction when MAC is reset.
         */
        ret_val = igb_disable_pcie_master(hw);
        if (ret_val)
                hw_dbg("PCI-E Master disable polling has failed.\n");

        /* set the completion timeout for interface */
        ret_val = igb_set_pcie_completion_timeout(hw);
        if (ret_val)
                hw_dbg("PCI-E Set completion timeout has failed.\n");

        hw_dbg("Masking off all interrupts\n");
        wr32(E1000_IMC, 0xffffffff);

        wr32(E1000_RCTL, 0);
        wr32(E1000_TCTL, E1000_TCTL_PSP);
        wrfl();

        usleep_range(10000, 20000);

        ctrl = rd32(E1000_CTRL);

        hw_dbg("Issuing a global reset to MAC\n");
        wr32(E1000_CTRL, ctrl | E1000_CTRL_RST);

        ret_val = igb_get_auto_rd_done(hw);
        if (ret_val) {
                /* When auto config read does not complete, do not
                 * return with an error. This can happen in situations
                 * where there is no eeprom and prevents getting link.
                 */
                hw_dbg("Auto Read Done did not complete\n");
        }

        /* If EEPROM is not present, run manual init scripts */
        if ((rd32(E1000_EECD) & E1000_EECD_PRES) == 0)
                igb_reset_init_script_82575(hw);

        /* Clear any pending interrupt events. */
        wr32(E1000_IMC, 0xffffffff);
        rd32(E1000_ICR);

        /* Install any alternate MAC address into RAR0 */
        ret_val = igb_check_alt_mac_addr(hw);

        return ret_val;
}

/**
 *  igb_init_hw_82575 - Initialize hardware
 *  @hw: pointer to the HW structure
 *
 *  This inits the hardware readying it for operation.
 **/
static s32 igb_init_hw_82575(struct e1000_hw *hw)
{
        struct e1000_mac_info *mac = &hw->mac;
        s32 ret_val;
        u16 i, rar_count = mac->rar_entry_count;

        if ((hw->mac.type >= e1000_i210) &&
            !(igb_get_flash_presence_i210(hw))) {
                ret_val = igb_pll_workaround_i210(hw);
                if (ret_val)
                        return ret_val;
        }

        /* Initialize identification LED */
        ret_val = igb_id_led_init(hw);
        if (ret_val) {
                hw_dbg("Error initializing identification LED\n");
                /* This is not fatal and we should not stop init due to this */
        }

        /* Disabling VLAN filtering */
        hw_dbg("Initializing the IEEE VLAN\n");
        igb_clear_vfta(hw);

        /* Setup the receive address */
        igb_init_rx_addrs(hw, rar_count);

        /* Zero out the Multicast HASH table */
        hw_dbg("Zeroing the MTA\n");
        for (i = 0; i < mac->mta_reg_count; i++)
                array_wr32(E1000_MTA, i, 0);

        /* Zero out the Unicast HASH table */
        hw_dbg("Zeroing the UTA\n");
        for (i = 0; i < mac->uta_reg_count; i++)
                array_wr32(E1000_UTA, i, 0);

        /* Setup link and flow control */
        ret_val = igb_setup_link(hw);

        /* Clear all of the statistics registers (clear on read).  It is
         * important that we do this after we have tried to establish link
         * because the symbol error count will increment wildly if there
         * is no link.
         */
        igb_clear_hw_cntrs_82575(hw);
        return ret_val;
}

/**
 *  igb_setup_copper_link_82575 - Configure copper link settings
 *  @hw: pointer to the HW structure
 *
 *  Configures the link for auto-neg or forced speed and duplex.  Then we check
 *  for link, once link is established calls to configure collision distance
 *  and flow control are called.
 **/
static s32 igb_setup_copper_link_82575(struct e1000_hw *hw)
{
        u32 ctrl;
        s32  ret_val;
        u32 phpm_reg;

        ctrl = rd32(E1000_CTRL);
        ctrl |= E1000_CTRL_SLU;
        ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
        wr32(E1000_CTRL, ctrl);

        /* Clear Go Link Disconnect bit on supported devices */
        switch (hw->mac.type) {
        case e1000_82580:
        case e1000_i350:
        case e1000_i210:
        case e1000_i211:
                phpm_reg = rd32(E1000_82580_PHY_POWER_MGMT);
                phpm_reg &= ~E1000_82580_PM_GO_LINKD;
                wr32(E1000_82580_PHY_POWER_MGMT, phpm_reg);
                break;
        default:
                break;
        }

        ret_val = igb_setup_serdes_link_82575(hw);
        if (ret_val)
                goto out;

        if (igb_sgmii_active_82575(hw) && !hw->phy.reset_disable) {
                /* allow time for SFP cage time to power up phy */
                msleep(300);

                ret_val = hw->phy.ops.reset(hw);
                if (ret_val) {
                        hw_dbg("Error resetting the PHY.\n");
                        goto out;
                }
        }
        switch (hw->phy.type) {
        case e1000_phy_i210:
        case e1000_phy_m88:
                switch (hw->phy.id) {
                case I347AT4_E_PHY_ID:
                case M88E1112_E_PHY_ID:
                case M88E1543_E_PHY_ID:
                case M88E1512_E_PHY_ID:
                case I210_I_PHY_ID:
                        ret_val = igb_copper_link_setup_m88_gen2(hw);
                        break;
                default:
                        ret_val = igb_copper_link_setup_m88(hw);
                        break;
                }
                break;
        case e1000_phy_igp_3:
                ret_val = igb_copper_link_setup_igp(hw);
                break;
        case e1000_phy_82580:
                ret_val = igb_copper_link_setup_82580(hw);
                break;
        case e1000_phy_bcm54616:
                ret_val = 0;
                break;
        default:
                ret_val = -E1000_ERR_PHY;
                break;
        }

        if (ret_val)
                goto out;

        ret_val = igb_setup_copper_link(hw);
out:
        return ret_val;
}

/**
 *  igb_setup_serdes_link_82575 - Setup link for serdes
 *  @hw: pointer to the HW structure
 *
 *  Configure the physical coding sub-layer (PCS) link.  The PCS link is
 *  used on copper connections where the serialized gigabit media independent
 *  interface (sgmii), or serdes fiber is being used.  Configures the link
 *  for auto-negotiation or forces speed/duplex.
 **/
static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw)
{
        u32 ctrl_ext, ctrl_reg, reg, anadv_reg;
        bool pcs_autoneg;
        s32 ret_val = 0;
        u16 data;

        if ((hw->phy.media_type != e1000_media_type_internal_serdes) &&
            !igb_sgmii_active_82575(hw))
                return ret_val;


        /* On the 82575, SerDes loopback mode persists until it is
         * explicitly turned off or a power cycle is performed.  A read to
         * the register does not indicate its status.  Therefore, we ensure
         * loopback mode is disabled during initialization.
         */
        wr32(E1000_SCTL, E1000_SCTL_DISABLE_SERDES_LOOPBACK);

        /* power on the sfp cage if present and turn on I2C */
        ctrl_ext = rd32(E1000_CTRL_EXT);
        ctrl_ext &= ~E1000_CTRL_EXT_SDP3_DATA;
        ctrl_ext |= E1000_CTRL_I2C_ENA;
        wr32(E1000_CTRL_EXT, ctrl_ext);

        ctrl_reg = rd32(E1000_CTRL);
        ctrl_reg |= E1000_CTRL_SLU;

        if (hw->mac.type == e1000_82575 || hw->mac.type == e1000_82576) {
                /* set both sw defined pins */
                ctrl_reg |= E1000_CTRL_SWDPIN0 | E1000_CTRL_SWDPIN1;

                /* Set switch control to serdes energy detect */
                reg = rd32(E1000_CONNSW);
                reg |= E1000_CONNSW_ENRGSRC;
                wr32(E1000_CONNSW, reg);
        }

        reg = rd32(E1000_PCS_LCTL);

        /* default pcs_autoneg to the same setting as mac autoneg */
        pcs_autoneg = hw->mac.autoneg;

        switch (ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK) {
        case E1000_CTRL_EXT_LINK_MODE_SGMII:
                /* sgmii mode lets the phy handle forcing speed/duplex */
                pcs_autoneg = true;
                /* autoneg time out should be disabled for SGMII mode */
                reg &= ~(E1000_PCS_LCTL_AN_TIMEOUT);
                break;
        case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX:
                /* disable PCS autoneg and support parallel detect only */
                pcs_autoneg = false;
                /* fall through */
        default:
                if (hw->mac.type == e1000_82575 ||
                    hw->mac.type == e1000_82576) {
                        ret_val = hw->nvm.ops.read(hw, NVM_COMPAT, 1, &data);
                        if (ret_val) {
                                hw_dbg(KERN_DEBUG "NVM Read Error\n\n");
                                return ret_val;
                        }

                        if (data & E1000_EEPROM_PCS_AUTONEG_DISABLE_BIT)
                                pcs_autoneg = false;
                }

                /* non-SGMII modes only supports a speed of 1000/Full for the
                 * link so it is best to just force the MAC and let the pcs
                 * link either autoneg or be forced to 1000/Full
                 */
                ctrl_reg |= E1000_CTRL_SPD_1000 | E1000_CTRL_FRCSPD |
                                E1000_CTRL_FD | E1000_CTRL_FRCDPX;

                /* set speed of 1000/Full if speed/duplex is forced */
                reg |= E1000_PCS_LCTL_FSV_1000 | E1000_PCS_LCTL_FDV_FULL;
                break;
        }

        wr32(E1000_CTRL, ctrl_reg);

        /* New SerDes mode allows for forcing speed or autonegotiating speed
         * at 1gb. Autoneg should be default set by most drivers. This is the
         * mode that will be compatible with older link partners and switches.
         * However, both are supported by the hardware and some drivers/tools.
         */
        reg &= ~(E1000_PCS_LCTL_AN_ENABLE | E1000_PCS_LCTL_FLV_LINK_UP |
                E1000_PCS_LCTL_FSD | E1000_PCS_LCTL_FORCE_LINK);

        if (pcs_autoneg) {
                /* Set PCS register for autoneg */
                reg |= E1000_PCS_LCTL_AN_ENABLE | /* Enable Autoneg */
                       E1000_PCS_LCTL_AN_RESTART; /* Restart autoneg */

                /* Disable force flow control for autoneg */
                reg &= ~E1000_PCS_LCTL_FORCE_FCTRL;

                /* Configure flow control advertisement for autoneg */
                anadv_reg = rd32(E1000_PCS_ANADV);
                anadv_reg &= ~(E1000_TXCW_ASM_DIR | E1000_TXCW_PAUSE);
                switch (hw->fc.requested_mode) {
                case e1000_fc_full:
                case e1000_fc_rx_pause:
                        anadv_reg |= E1000_TXCW_ASM_DIR;
                        anadv_reg |= E1000_TXCW_PAUSE;
                        break;
                case e1000_fc_tx_pause:
                        anadv_reg |= E1000_TXCW_ASM_DIR;
                        break;
                default:
                        break;
                }
                wr32(E1000_PCS_ANADV, anadv_reg);

                hw_dbg("Configuring Autoneg:PCS_LCTL=0x%08X\n", reg);
        } else {
                /* Set PCS register for forced link */
                reg |= E1000_PCS_LCTL_FSD;        /* Force Speed */

                /* Force flow control for forced link */
                reg |= E1000_PCS_LCTL_FORCE_FCTRL;

                hw_dbg("Configuring Forced Link:PCS_LCTL=0x%08X\n", reg);
        }

        wr32(E1000_PCS_LCTL, reg);

        if (!pcs_autoneg && !igb_sgmii_active_82575(hw))
                igb_force_mac_fc(hw);

        return ret_val;
}

/**
 *  igb_sgmii_active_82575 - Return sgmii state
 *  @hw: pointer to the HW structure
 *
 *  82575 silicon has a serialized gigabit media independent interface (sgmii)
 *  which can be enabled for use in the embedded applications.  Simply
 *  return the current state of the sgmii interface.
 **/
static bool igb_sgmii_active_82575(struct e1000_hw *hw)
{
        struct e1000_dev_spec_82575 *dev_spec = &hw->dev_spec._82575;
        return dev_spec->sgmii_active;
}

/**
 *  igb_reset_init_script_82575 - Inits HW defaults after reset
 *  @hw: pointer to the HW structure
 *
 *  Inits recommended HW defaults after a reset when there is no EEPROM
 *  detected. This is only for the 82575.
 **/
static s32 igb_reset_init_script_82575(struct e1000_hw *hw)
{
        if (hw->mac.type == e1000_82575) {
                hw_dbg("Running reset init script for 82575\n");
                /* SerDes configuration via SERDESCTRL */
                igb_write_8bit_ctrl_reg(hw, E1000_SCTL, 0x00, 0x0C);
                igb_write_8bit_ctrl_reg(hw, E1000_SCTL, 0x01, 0x78);
                igb_write_8bit_ctrl_reg(hw, E1000_SCTL, 0x1B, 0x23);
                igb_write_8bit_ctrl_reg(hw, E1000_SCTL, 0x23, 0x15);

                /* CCM configuration via CCMCTL register */
                igb_write_8bit_ctrl_reg(hw, E1000_CCMCTL, 0x14, 0x00);
                igb_write_8bit_ctrl_reg(hw, E1000_CCMCTL, 0x10, 0x00);

                /* PCIe lanes configuration */
                igb_write_8bit_ctrl_reg(hw, E1000_GIOCTL, 0x00, 0xEC);
                igb_write_8bit_ctrl_reg(hw, E1000_GIOCTL, 0x61, 0xDF);
                igb_write_8bit_ctrl_reg(hw, E1000_GIOCTL, 0x34, 0x05);
                igb_write_8bit_ctrl_reg(hw, E1000_GIOCTL, 0x2F, 0x81);

                /* PCIe PLL Configuration */
                igb_write_8bit_ctrl_reg(hw, E1000_SCCTL, 0x02, 0x47);
                igb_write_8bit_ctrl_reg(hw, E1000_SCCTL, 0x14, 0x00);
                igb_write_8bit_ctrl_reg(hw, E1000_SCCTL, 0x10, 0x00);
        }

        return 0;
}

/**
 *  igb_read_mac_addr_82575 - Read device MAC address
 *  @hw: pointer to the HW structure
 **/
static s32 igb_read_mac_addr_82575(struct e1000_hw *hw)
{
        s32 ret_val = 0;

        /* If there's an alternate MAC address place it in RAR0
         * so that it will override the Si installed default perm
         * address.
         */
        ret_val = igb_check_alt_mac_addr(hw);
        if (ret_val)
                goto out;

        ret_val = igb_read_mac_addr(hw);

out:
        return ret_val;
}

/**
 * igb_power_down_phy_copper_82575 - Remove link during PHY power down
 * @hw: pointer to the HW structure
 *
 * In the case of a PHY power down to save power, or to turn off link during a
 * driver unload, or wake on lan is not enabled, remove the link.
 **/
void igb_power_down_phy_copper_82575(struct e1000_hw *hw)
{
        /* If the management interface is not enabled, then power down */
        if (!(igb_enable_mng_pass_thru(hw) || igb_check_reset_block(hw)))
                igb_power_down_phy_copper(hw);
}

/**
 *  igb_clear_hw_cntrs_82575 - Clear device specific hardware counters
 *  @hw: pointer to the HW structure
 *
 *  Clears the hardware counters by reading the counter registers.
 **/
static void igb_clear_hw_cntrs_82575(struct e1000_hw *hw)
{
        igb_clear_hw_cntrs_base(hw);

        rd32(E1000_PRC64);
        rd32(E1000_PRC127);
        rd32(E1000_PRC255);
        rd32(E1000_PRC511);
        rd32(E1000_PRC1023);
        rd32(E1000_PRC1522);
        rd32(E1000_PTC64);
        rd32(E1000_PTC127);
        rd32(E1000_PTC255);
        rd32(E1000_PTC511);
        rd32(E1000_PTC1023);
        rd32(E1000_PTC1522);

        rd32(E1000_ALGNERRC);
        rd32(E1000_RXERRC);
        rd32(E1000_TNCRS);
        rd32(E1000_CEXTERR);
        rd32(E1000_TSCTC);
        rd32(E1000_TSCTFC);

        rd32(E1000_MGTPRC);
        rd32(E1000_MGTPDC);
        rd32(E1000_MGTPTC);

        rd32(E1000_IAC);
        rd32(E1000_ICRXOC);

        rd32(E1000_ICRXPTC);
        rd32(E1000_ICRXATC);
        rd32(E1000_ICTXPTC);
        rd32(E1000_ICTXATC);
        rd32(E1000_ICTXQEC);
        rd32(E1000_ICTXQMTC);
        rd32(E1000_ICRXDMTC);

        rd32(E1000_CBTMPC);
        rd32(E1000_HTDPMC);
        rd32(E1000_CBRMPC);
        rd32(E1000_RPTHC);
        rd32(E1000_HGPTC);
        rd32(E1000_HTCBDPC);
        rd32(E1000_HGORCL);
        rd32(E1000_HGORCH);
        rd32(E1000_HGOTCL);
        rd32(E1000_HGOTCH);
        rd32(E1000_LENERRS);

        /* This register should not be read in copper configurations */
        if (hw->phy.media_type == e1000_media_type_internal_serdes ||
            igb_sgmii_active_82575(hw))
                rd32(E1000_SCVPC);
}

/**
 *  igb_rx_fifo_flush_82575 - Clean rx fifo after RX enable
 *  @hw: pointer to the HW structure
 *
 *  After rx enable if manageability is enabled then there is likely some
 *  bad data at the start of the fifo and possibly in the DMA fifo. This
 *  function clears the fifos and flushes any packets that came in as rx was
 *  being enabled.
 **/
void igb_rx_fifo_flush_82575(struct e1000_hw *hw)
{
        u32 rctl, rlpml, rxdctl[4], rfctl, temp_rctl, rx_enabled;
        int i, ms_wait;

        /* disable IPv6 options as per hardware errata */
        rfctl = rd32(E1000_RFCTL);
        rfctl |= E1000_RFCTL_IPV6_EX_DIS;
        wr32(E1000_RFCTL, rfctl);

        if (hw->mac.type != e1000_82575 ||
            !(rd32(E1000_MANC) & E1000_MANC_RCV_TCO_EN))
                return;

        /* Disable all RX queues */
        for (i = 0; i < 4; i++) {
                rxdctl[i] = rd32(E1000_RXDCTL(i));
                wr32(E1000_RXDCTL(i),
                     rxdctl[i] & ~E1000_RXDCTL_QUEUE_ENABLE);
        }
        /* Poll all queues to verify they have shut down */
        for (ms_wait = 0; ms_wait < 10; ms_wait++) {
                usleep_range(1000, 2000);
                rx_enabled = 0;
                for (i = 0; i < 4; i++)
                        rx_enabled |= rd32(E1000_RXDCTL(i));
                if (!(rx_enabled & E1000_RXDCTL_QUEUE_ENABLE))
                        break;
        }

        if (ms_wait == 10)
                hw_dbg("Queue disable timed out after 10ms\n");

        /* Clear RLPML, RCTL.SBP, RFCTL.LEF, and set RCTL.LPE so that all
         * incoming packets are rejected.  Set enable and wait 2ms so that
         * any packet that was coming in as RCTL.EN was set is flushed
         */
        wr32(E1000_RFCTL, rfctl & ~E1000_RFCTL_LEF);

        rlpml = rd32(E1000_RLPML);
        wr32(E1000_RLPML, 0);

        rctl = rd32(E1000_RCTL);
        temp_rctl = rctl & ~(E1000_RCTL_EN | E1000_RCTL_SBP);
        temp_rctl |= E1000_RCTL_LPE;

        wr32(E1000_RCTL, temp_rctl);
        wr32(E1000_RCTL, temp_rctl | E1000_RCTL_EN);
        wrfl();
        usleep_range(2000, 3000);

        /* Enable RX queues that were previously enabled and restore our

         * previous state
         */
        for (i = 0; i < 4; i++)
                wr32(E1000_RXDCTL(i), rxdctl[i]);
        wr32(E1000_RCTL, rctl);
        wrfl();

        wr32(E1000_RLPML, rlpml);
        wr32(E1000_RFCTL, rfctl);

        /* Flush receive errors generated by workaround */
        rd32(E1000_ROC);
        rd32(E1000_RNBC);
        rd32(E1000_MPC);
}

/**
 *  igb_set_pcie_completion_timeout - set pci-e completion timeout
 *  @hw: pointer to the HW structure
 *
 *  The defaults for 82575 and 82576 should be in the range of 50us to 50ms,
 *  however the hardware default for these parts is 500us to 1ms which is less
 *  than the 10ms recommended by the pci-e spec.  To address this we need to
 *  increase the value to either 10ms to 200ms for capability version 1 config,
 *  or 16ms to 55ms for version 2.
 **/
static s32 igb_set_pcie_completion_timeout(struct e1000_hw *hw)
{
        u32 gcr = rd32(E1000_GCR);
        s32 ret_val = 0;
        u16 pcie_devctl2;

        /* only take action if timeout value is defaulted to 0 */
        if (gcr & E1000_GCR_CMPL_TMOUT_MASK)
                goto out;

        /* if capabilities version is type 1 we can write the
         * timeout of 10ms to 200ms through the GCR register
         */
        if (!(gcr & E1000_GCR_CAP_VER2)) {
                gcr |= E1000_GCR_CMPL_TMOUT_10ms;
                goto out;
        }

        /* for version 2 capabilities we need to write the config space
         * directly in order to set the completion timeout value for
         * 16ms to 55ms
         */
        ret_val = igb_read_pcie_cap_reg(hw, PCIE_DEVICE_CONTROL2,
                                        &pcie_devctl2);
        if (ret_val)
                goto out;

        pcie_devctl2 |= PCIE_DEVICE_CONTROL2_16ms;

        ret_val = igb_write_pcie_cap_reg(hw, PCIE_DEVICE_CONTROL2,
                                         &pcie_devctl2);
out:
        /* disable completion timeout resend */
        gcr &= ~E1000_GCR_CMPL_TMOUT_RESEND;

        wr32(E1000_GCR, gcr);
        return ret_val;
}

/**
 *  igb_vmdq_set_anti_spoofing_pf - enable or disable anti-spoofing
 *  @hw: pointer to the hardware struct
 *  @enable: state to enter, either enabled or disabled
 *  @pf: Physical Function pool - do not set anti-spoofing for the PF
 *
 *  enables/disables L2 switch anti-spoofing functionality.
 **/
void igb_vmdq_set_anti_spoofing_pf(struct e1000_hw *hw, bool enable, int pf)
{
        u32 reg_val, reg_offset;

        switch (hw->mac.type) {
        case e1000_82576:
                reg_offset = E1000_DTXSWC;
                break;
        case e1000_i350:
        case e1000_i354:
                reg_offset = E1000_TXSWC;
                break;
        default:
                return;
        }

        reg_val = rd32(reg_offset);
        if (enable) {
                reg_val |= (E1000_DTXSWC_MAC_SPOOF_MASK |
                             E1000_DTXSWC_VLAN_SPOOF_MASK);
                /* The PF can spoof - it has to in order to
                 * support emulation mode NICs
                 */
                reg_val ^= (BIT(pf) | BIT(pf + MAX_NUM_VFS));
        } else {
                reg_val &= ~(E1000_DTXSWC_MAC_SPOOF_MASK |
                             E1000_DTXSWC_VLAN_SPOOF_MASK);
        }
        wr32(reg_offset, reg_val);
}

/**
 *  igb_vmdq_set_loopback_pf - enable or disable vmdq loopback
 *  @hw: pointer to the hardware struct
 *  @enable: state to enter, either enabled or disabled
 *
 *  enables/disables L2 switch loopback functionality.
 **/
void igb_vmdq_set_loopback_pf(struct e1000_hw *hw, bool enable)
{
        u32 dtxswc;

        switch (hw->mac.type) {
        case e1000_82576:
                dtxswc = rd32(E1000_DTXSWC);
                if (enable)
                        dtxswc |= E1000_DTXSWC_VMDQ_LOOPBACK_EN;
                else
                        dtxswc &= ~E1000_DTXSWC_VMDQ_LOOPBACK_EN;
                wr32(E1000_DTXSWC, dtxswc);
                break;
        case e1000_i354:
        case e1000_i350:
                dtxswc = rd32(E1000_TXSWC);
                if (enable)
                        dtxswc |= E1000_DTXSWC_VMDQ_LOOPBACK_EN;
                else
                        dtxswc &= ~E1000_DTXSWC_VMDQ_LOOPBACK_EN;
                wr32(E1000_TXSWC, dtxswc);
                break;
        default:
                /* Currently no other hardware supports loopback */
                break;
        }

}

/**
 *  igb_vmdq_set_replication_pf - enable or disable vmdq replication
 *  @hw: pointer to the hardware struct
 *  @enable: state to enter, either enabled or disabled
 *
 *  enables/disables replication of packets across multiple pools.
 **/
void igb_vmdq_set_replication_pf(struct e1000_hw *hw, bool enable)
{
        u32 vt_ctl = rd32(E1000_VT_CTL);

        if (enable)
                vt_ctl |= E1000_VT_CTL_VM_REPL_EN;
        else
                vt_ctl &= ~E1000_VT_CTL_VM_REPL_EN;

        wr32(E1000_VT_CTL, vt_ctl);
}

/**
 *  igb_read_phy_reg_82580 - Read 82580 MDI control register
 *  @hw: pointer to the HW structure
 *  @offset: register offset to be read
 *  @data: pointer to the read data
 *
 *  Reads the MDI control register in the PHY at offset and stores the
 *  information read to data.
 **/
s32 igb_read_phy_reg_82580(struct e1000_hw *hw, u32 offset, u16 *data)
{
        s32 ret_val;

        ret_val = hw->phy.ops.acquire(hw);
        if (ret_val)
                goto out;

        ret_val = igb_read_phy_reg_mdic(hw, offset, data);

        hw->phy.ops.release(hw);

out:
        return ret_val;
}

/**
 *  igb_write_phy_reg_82580 - Write 82580 MDI control register
 *  @hw: pointer to the HW structure
 *  @offset: register offset to write to
 *  @data: data to write to register at offset
 *
 *  Writes data to MDI control register in the PHY at offset.
 **/
s32 igb_write_phy_reg_82580(struct e1000_hw *hw, u32 offset, u16 data)
{
        s32 ret_val;


        ret_val = hw->phy.ops.acquire(hw);
        if (ret_val)
                goto out;

        ret_val = igb_write_phy_reg_mdic(hw, offset, data);

        hw->phy.ops.release(hw);

out:
        return ret_val;
}

/**
 *  igb_reset_mdicnfg_82580 - Reset MDICNFG destination and com_mdio bits
 *  @hw: pointer to the HW structure
 *
 *  This resets the the MDICNFG.Destination and MDICNFG.Com_MDIO bits based on
 *  the values found in the EEPROM.  This addresses an issue in which these
 *  bits are not restored from EEPROM after reset.
 **/
static s32 igb_reset_mdicnfg_82580(struct e1000_hw *hw)
{
        s32 ret_val = 0;
        u32 mdicnfg;
        u16 nvm_data = 0;

        if (hw->mac.type != e1000_82580)
                goto out;
        if (!igb_sgmii_active_82575(hw))
                goto out;

        ret_val = hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A +
                                   NVM_82580_LAN_FUNC_OFFSET(hw->bus.func), 1,
                                   &nvm_data);
        if (ret_val) {
                hw_dbg("NVM Read Error\n");
                goto out;
        }

        mdicnfg = rd32(E1000_MDICNFG);
        if (nvm_data & NVM_WORD24_EXT_MDIO)
                mdicnfg |= E1000_MDICNFG_EXT_MDIO;
        if (nvm_data & NVM_WORD24_COM_MDIO)
                mdicnfg |= E1000_MDICNFG_COM_MDIO;
        wr32(E1000_MDICNFG, mdicnfg);
out:
        return ret_val;
}

/**
 *  igb_reset_hw_82580 - Reset hardware
 *  @hw: pointer to the HW structure
 *
 *  This resets function or entire device (all ports, etc.)
 *  to a known state.
 **/
static s32 igb_reset_hw_82580(struct e1000_hw *hw)
{
        s32 ret_val = 0;
        /* BH SW mailbox bit in SW_FW_SYNC */
        u16 swmbsw_mask = E1000_SW_SYNCH_MB;
        u32 ctrl;
        bool global_device_reset = hw->dev_spec._82575.global_device_reset;

        hw->dev_spec._82575.global_device_reset = false;

        /* due to hw errata, global device reset doesn't always
         * work on 82580
         */
        if (hw->mac.type == e1000_82580)
                global_device_reset = false;

        /* Get current control state. */
        ctrl = rd32(E1000_CTRL);

        /* Prevent the PCI-E bus from sticking if there is no TLP connection
         * on the last TLP read/write transaction when MAC is reset.
         */
        ret_val = igb_disable_pcie_master(hw);
        if (ret_val)
                hw_dbg("PCI-E Master disable polling has failed.\n");

        hw_dbg("Masking off all interrupts\n");
        wr32(E1000_IMC, 0xffffffff);
        wr32(E1000_RCTL, 0);
        wr32(E1000_TCTL, E1000_TCTL_PSP);
        wrfl();

        usleep_range(10000, 11000);

        /* Determine whether or not a global dev reset is requested */
        if (global_device_reset &&
                hw->mac.ops.acquire_swfw_sync(hw, swmbsw_mask))
                        global_device_reset = false;

        if (global_device_reset &&
                !(rd32(E1000_STATUS) & E1000_STAT_DEV_RST_SET))
                ctrl |= E1000_CTRL_DEV_RST;
        else
                ctrl |= E1000_CTRL_RST;

        wr32(E1000_CTRL, ctrl);
        wrfl();

        /* Add delay to insure DEV_RST has time to complete */
        if (global_device_reset)
                usleep_range(5000, 6000);

        ret_val = igb_get_auto_rd_done(hw);
        if (ret_val) {
                /* When auto config read does not complete, do not
                 * return with an error. This can happen in situations
                 * where there is no eeprom and prevents getting link.
                 */
                hw_dbg("Auto Read Done did not complete\n");
        }

        /* clear global device reset status bit */
        wr32(E1000_STATUS, E1000_STAT_DEV_RST_SET);

        /* Clear any pending interrupt events. */
        wr32(E1000_IMC, 0xffffffff);
        rd32(E1000_ICR);

        ret_val = igb_reset_mdicnfg_82580(hw);
        if (ret_val)
                hw_dbg("Could not reset MDICNFG based on EEPROM\n");

        /* Install any alternate MAC address into RAR0 */
        ret_val = igb_check_alt_mac_addr(hw);

        /* Release semaphore */
        if (global_device_reset)
                hw->mac.ops.release_swfw_sync(hw, swmbsw_mask);

        return ret_val;
}

/**
 *  igb_rxpbs_adjust_82580 - adjust RXPBS value to reflect actual RX PBA size
 *  @data: data received by reading RXPBS register
 *
 *  The 82580 uses a table based approach for packet buffer allocation sizes.
 *  This function converts the retrieved value into the correct table value
 *     0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7
 *  0x0 36  72 144   1   2   4   8  16
 *  0x8 35  70 140 rsv rsv rsv rsv rsv
 */
u16 igb_rxpbs_adjust_82580(u32 data)
{
        u16 ret_val = 0;

        if (data < ARRAY_SIZE(e1000_82580_rxpbs_table))
                ret_val = e1000_82580_rxpbs_table[data];

        return ret_val;
}

/**
 *  igb_validate_nvm_checksum_with_offset - Validate EEPROM
 *  checksum
 *  @hw: pointer to the HW structure
 *  @offset: offset in words of the checksum protected region
 *
 *  Calculates the EEPROM checksum by reading/adding each word of the EEPROM
 *  and then verifies that the sum of the EEPROM is equal to 0xBABA.
 **/
static s32 igb_validate_nvm_checksum_with_offset(struct e1000_hw *hw,
                                                 u16 offset)
{
        s32 ret_val = 0;
        u16 checksum = 0;
        u16 i, nvm_data;

        for (i = offset; i < ((NVM_CHECKSUM_REG + offset) + 1); i++) {
                ret_val = hw->nvm.ops.read(hw, i, 1, &nvm_data);
                if (ret_val) {
                        hw_dbg("NVM Read Error\n");
                        goto out;
                }
                checksum += nvm_data;
        }

        if (checksum != (u16) NVM_SUM) {
                hw_dbg("NVM Checksum Invalid\n");
                ret_val = -E1000_ERR_NVM;
                goto out;
        }

out:
        return ret_val;
}

/**
 *  igb_update_nvm_checksum_with_offset - Update EEPROM
 *  checksum
 *  @hw: pointer to the HW structure
 *  @offset: offset in words of the checksum protected region
 *
 *  Updates the EEPROM checksum by reading/adding each word of the EEPROM
 *  up to the checksum.  Then calculates the EEPROM checksum and writes the
 *  value to the EEPROM.
 **/
static s32 igb_update_nvm_checksum_with_offset(struct e1000_hw *hw, u16 offset)
{
        s32 ret_val;
        u16 checksum = 0;
        u16 i, nvm_data;

        for (i = offset; i < (NVM_CHECKSUM_REG + offset); i++) {
                ret_val = hw->nvm.ops.read(hw, i, 1, &nvm_data);
                if (ret_val) {
                        hw_dbg("NVM Read Error while updating checksum.\n");
                        goto out;
                }
                checksum += nvm_data;
        }
        checksum = (u16) NVM_SUM - checksum;
        ret_val = hw->nvm.ops.write(hw, (NVM_CHECKSUM_REG + offset), 1,
                                &checksum);
        if (ret_val)
                hw_dbg("NVM Write Error while updating checksum.\n");

out:
        return ret_val;
}

/**
 *  igb_validate_nvm_checksum_82580 - Validate EEPROM checksum
 *  @hw: pointer to the HW structure
 *
 *  Calculates the EEPROM section checksum by reading/adding each word of
 *  the EEPROM and then verifies that the sum of the EEPROM is
 *  equal to 0xBABA.
 **/
static s32 igb_validate_nvm_checksum_82580(struct e1000_hw *hw)
{
        s32 ret_val = 0;
        u16 eeprom_regions_count = 1;
        u16 j, nvm_data;
        u16 nvm_offset;

        ret_val = hw->nvm.ops.read(hw, NVM_COMPATIBILITY_REG_3, 1, &nvm_data);
        if (ret_val) {
                hw_dbg("NVM Read Error\n");
                goto out;
        }

        if (nvm_data & NVM_COMPATIBILITY_BIT_MASK) {
                /* if checksums compatibility bit is set validate checksums
                 * for all 4 ports.
                 */
                eeprom_regions_count = 4;
        }

        for (j = 0; j < eeprom_regions_count; j++) {
                nvm_offset = NVM_82580_LAN_FUNC_OFFSET(j);
                ret_val = igb_validate_nvm_checksum_with_offset(hw,
                                                                nvm_offset);
                if (ret_val != 0)
                        goto out;
        }

out:
        return ret_val;
}

/**
 *  igb_update_nvm_checksum_82580 - Update EEPROM checksum
 *  @hw: pointer to the HW structure
 *
 *  Updates the EEPROM section checksums for all 4 ports by reading/adding
 *  each word of the EEPROM up to the checksum.  Then calculates the EEPROM
 *  checksum and writes the value to the EEPROM.
 **/
static s32 igb_update_nvm_checksum_82580(struct e1000_hw *hw)
{
        s32 ret_val;
        u16 j, nvm_data;
        u16 nvm_offset;

        ret_val = hw->nvm.ops.read(hw, NVM_COMPATIBILITY_REG_3, 1, &nvm_data);
        if (ret_val) {
                hw_dbg("NVM Read Error while updating checksum compatibility bit.\n");
                goto out;
        }

        if ((nvm_data & NVM_COMPATIBILITY_BIT_MASK) == 0) {
                /* set compatibility bit to validate checksums appropriately */
                nvm_data = nvm_data | NVM_COMPATIBILITY_BIT_MASK;
                ret_val = hw->nvm.ops.write(hw, NVM_COMPATIBILITY_REG_3, 1,
                                        &nvm_data);
                if (ret_val) {
                        hw_dbg("NVM Write Error while updating checksum compatibility bit.\n");
                        goto out;
                }
        }

        for (j = 0; j < 4; j++) {
                nvm_offset = NVM_82580_LAN_FUNC_OFFSET(j);
                ret_val = igb_update_nvm_checksum_with_offset(hw, nvm_offset);
                if (ret_val)
                        goto out;
        }

out:
        return ret_val;
}

/**
 *  igb_validate_nvm_checksum_i350 - Validate EEPROM checksum
 *  @hw: pointer to the HW structure
 *
 *  Calculates the EEPROM section checksum by reading/adding each word of
 *  the EEPROM and then verifies that the sum of the EEPROM is
 *  equal to 0xBABA.
 **/
static s32 igb_validate_nvm_checksum_i350(struct e1000_hw *hw)
{
        s32 ret_val = 0;
        u16 j;
        u16 nvm_offset;

        for (j = 0; j < 4; j++) {
                nvm_offset = NVM_82580_LAN_FUNC_OFFSET(j);
                ret_val = igb_validate_nvm_checksum_with_offset(hw,
                                                                nvm_offset);
                if (ret_val != 0)
                        goto out;
        }

out:
        return ret_val;
}

/**
 *  igb_update_nvm_checksum_i350 - Update EEPROM checksum
 *  @hw: pointer to the HW structure
 *
 *  Updates the EEPROM section checksums for all 4 ports by reading/adding
 *  each word of the EEPROM up to the checksum.  Then calculates the EEPROM
 *  checksum and writes the value to the EEPROM.
 **/
static s32 igb_update_nvm_checksum_i350(struct e1000_hw *hw)
{
        s32 ret_val = 0;
        u16 j;
        u16 nvm_offset;

        for (j = 0; j < 4; j++) {
                nvm_offset = NVM_82580_LAN_FUNC_OFFSET(j);
                ret_val = igb_update_nvm_checksum_with_offset(hw, nvm_offset);
                if (ret_val != 0)
                        goto out;
        }

out:
        return ret_val;
}

/**
 *  __igb_access_emi_reg - Read/write EMI register
 *  @hw: pointer to the HW structure
 *  @addr: EMI address to program
 *  @data: pointer to value to read/write from/to the EMI address
 *  @read: boolean flag to indicate read or write
 **/
static s32 __igb_access_emi_reg(struct e1000_hw *hw, u16 address,
                                  u16 *data, bool read)
{
        s32 ret_val = 0;

        ret_val = hw->phy.ops.write_reg(hw, E1000_EMIADD, address);
        if (ret_val)
                return ret_val;

        if (read)
                ret_val = hw->phy.ops.read_reg(hw, E1000_EMIDATA, data);
        else
                ret_val = hw->phy.ops.write_reg(hw, E1000_EMIDATA, *data);

        return ret_val;
}

/**
 *  igb_read_emi_reg - Read Extended Management Interface register
 *  @hw: pointer to the HW structure
 *  @addr: EMI address to program
 *  @data: value to be read from the EMI address
 **/
s32 igb_read_emi_reg(struct e1000_hw *hw, u16 addr, u16 *data)
{
        return __igb_access_emi_reg(hw, addr, data, true);
}

/**
 *  igb_set_eee_i350 - Enable/disable EEE support
 *  @hw: pointer to the HW structure
 *  @adv1G: boolean flag enabling 1G EEE advertisement
 *  @adv100m: boolean flag enabling 100M EEE advertisement
 *
 *  Enable/disable EEE based on setting in dev_spec structure.
 *
 **/
s32 igb_set_eee_i350(struct e1000_hw *hw, bool adv1G, bool adv100M)
{
        u32 ipcnfg, eeer;

        if ((hw->mac.type < e1000_i350) ||
            (hw->phy.media_type != e1000_media_type_copper))
                goto out;
        ipcnfg = rd32(E1000_IPCNFG);
        eeer = rd32(E1000_EEER);

        /* enable or disable per user setting */
        if (!(hw->dev_spec._82575.eee_disable)) {
                u32 eee_su = rd32(E1000_EEE_SU);

                if (adv100M)
                        ipcnfg |= E1000_IPCNFG_EEE_100M_AN;
                else
                        ipcnfg &= ~E1000_IPCNFG_EEE_100M_AN;

                if (adv1G)
                        ipcnfg |= E1000_IPCNFG_EEE_1G_AN;
                else
                        ipcnfg &= ~E1000_IPCNFG_EEE_1G_AN;

                eeer |= (E1000_EEER_TX_LPI_EN | E1000_EEER_RX_LPI_EN |
                        E1000_EEER_LPI_FC);

                /* This bit should not be set in normal operation. */
                if (eee_su & E1000_EEE_SU_LPI_CLK_STP)
                        hw_dbg("LPI Clock Stop Bit should not be set!\n");

        } else {
                ipcnfg &= ~(E1000_IPCNFG_EEE_1G_AN |
                        E1000_IPCNFG_EEE_100M_AN);
                eeer &= ~(E1000_EEER_TX_LPI_EN |
                        E1000_EEER_RX_LPI_EN |
                        E1000_EEER_LPI_FC);
        }
        wr32(E1000_IPCNFG, ipcnfg);
        wr32(E1000_EEER, eeer);
        rd32(E1000_IPCNFG);
        rd32(E1000_EEER);
out:

        return 0;
}

/**
 *  igb_set_eee_i354 - Enable/disable EEE support
 *  @hw: pointer to the HW structure
 *  @adv1G: boolean flag enabling 1G EEE advertisement
 *  @adv100m: boolean flag enabling 100M EEE advertisement
 *
 *  Enable/disable EEE legacy mode based on setting in dev_spec structure.
 *
 **/
s32 igb_set_eee_i354(struct e1000_hw *hw, bool adv1G, bool adv100M)
{
        struct e1000_phy_info *phy = &hw->phy;
        s32 ret_val = 0;
        u16 phy_data;

        if ((hw->phy.media_type != e1000_media_type_copper) ||
            ((phy->id != M88E1543_E_PHY_ID) &&
             (phy->id != M88E1512_E_PHY_ID)))
                goto out;

        if (!hw->dev_spec._82575.eee_disable) {
                /* Switch to PHY page 18. */
                ret_val = phy->ops.write_reg(hw, E1000_M88E1543_PAGE_ADDR, 18);
                if (ret_val)
                        goto out;

                ret_val = phy->ops.read_reg(hw, E1000_M88E1543_EEE_CTRL_1,
                                            &phy_data);
                if (ret_val)
                        goto out;

                phy_data |= E1000_M88E1543_EEE_CTRL_1_MS;
                ret_val = phy->ops.write_reg(hw, E1000_M88E1543_EEE_CTRL_1,
                                             phy_data);
                if (ret_val)
                        goto out;

                /* Return the PHY to page 0. */
                ret_val = phy->ops.write_reg(hw, E1000_M88E1543_PAGE_ADDR, 0);
                if (ret_val)
                        goto out;

                /* Turn on EEE advertisement. */
                ret_val = igb_read_xmdio_reg(hw, E1000_EEE_ADV_ADDR_I354,
                                             E1000_EEE_ADV_DEV_I354,
                                             &phy_data);
                if (ret_val)
                        goto out;

                if (adv100M)
                        phy_data |= E1000_EEE_ADV_100_SUPPORTED;
                else
                        phy_data &= ~E1000_EEE_ADV_100_SUPPORTED;

                if (adv1G)
                        phy_data |= E1000_EEE_ADV_1000_SUPPORTED;
                else
                        phy_data &= ~E1000_EEE_ADV_1000_SUPPORTED;

                ret_val = igb_write_xmdio_reg(hw, E1000_EEE_ADV_ADDR_I354,
                                                E1000_EEE_ADV_DEV_I354,
                                                phy_data);
        } else {
                /* Turn off EEE advertisement. */
                ret_val = igb_read_xmdio_reg(hw, E1000_EEE_ADV_ADDR_I354,
                                             E1000_EEE_ADV_DEV_I354,
                                             &phy_data);
                if (ret_val)
                        goto out;

                phy_data &= ~(E1000_EEE_ADV_100_SUPPORTED |
                              E1000_EEE_ADV_1000_SUPPORTED);
                ret_val = igb_write_xmdio_reg(hw, E1000_EEE_ADV_ADDR_I354,
                                              E1000_EEE_ADV_DEV_I354,
                                              phy_data);
        }

out:
        return ret_val;
}

/**
 *  igb_get_eee_status_i354 - Get EEE status
 *  @hw: pointer to the HW structure
 *  @status: EEE status
 *
 *  Get EEE status by guessing based on whether Tx or Rx LPI indications have
 *  been received.
 **/
s32 igb_get_eee_status_i354(struct e1000_hw *hw, bool *status)
{
        struct e1000_phy_info *phy = &hw->phy;
        s32 ret_val = 0;
        u16 phy_data;

        /* Check if EEE is supported on this device. */
        if ((hw->phy.media_type != e1000_media_type_copper) ||
            ((phy->id != M88E1543_E_PHY_ID) &&
             (phy->id != M88E1512_E_PHY_ID)))
                goto out;

        ret_val = igb_read_xmdio_reg(hw, E1000_PCS_STATUS_ADDR_I354,
                                     E1000_PCS_STATUS_DEV_I354,
                                     &phy_data);
        if (ret_val)
                goto out;

        *status = phy_data & (E1000_PCS_STATUS_TX_LPI_RCVD |
                              E1000_PCS_STATUS_RX_LPI_RCVD) ? true : false;

out:
        return ret_val;
}

static const u8 e1000_emc_temp_data[4] = {
        E1000_EMC_INTERNAL_DATA,
        E1000_EMC_DIODE1_DATA,
        E1000_EMC_DIODE2_DATA,
        E1000_EMC_DIODE3_DATA
};
static const u8 e1000_emc_therm_limit[4] = {
        E1000_EMC_INTERNAL_THERM_LIMIT,
        E1000_EMC_DIODE1_THERM_LIMIT,
        E1000_EMC_DIODE2_THERM_LIMIT,
        E1000_EMC_DIODE3_THERM_LIMIT
};

#ifdef CONFIG_IGB_HWMON
/**
 *  igb_get_thermal_sensor_data_generic - Gathers thermal sensor data
 *  @hw: pointer to hardware structure
 *
 *  Updates the temperatures in mac.thermal_sensor_data
 **/
static s32 igb_get_thermal_sensor_data_generic(struct e1000_hw *hw)
{
        u16 ets_offset;
        u16 ets_cfg;
        u16 ets_sensor;
        u8  num_sensors;
        u8  sensor_index;
        u8  sensor_location;
        u8  i;
        struct e1000_thermal_sensor_data *data = &hw->mac.thermal_sensor_data;

        if ((hw->mac.type != e1000_i350) || (hw->bus.func != 0))
                return E1000_NOT_IMPLEMENTED;

        data->sensor[0].temp = (rd32(E1000_THMJT) & 0xFF);

        /* Return the internal sensor only if ETS is unsupported */
        hw->nvm.ops.read(hw, NVM_ETS_CFG, 1, &ets_offset);
        if ((ets_offset == 0x0000) || (ets_offset == 0xFFFF))
                return 0;

        hw->nvm.ops.read(hw, ets_offset, 1, &ets_cfg);
        if (((ets_cfg & NVM_ETS_TYPE_MASK) >> NVM_ETS_TYPE_SHIFT)
            != NVM_ETS_TYPE_EMC)
                return E1000_NOT_IMPLEMENTED;

        num_sensors = (ets_cfg & NVM_ETS_NUM_SENSORS_MASK);
        if (num_sensors > E1000_MAX_SENSORS)
                num_sensors = E1000_MAX_SENSORS;

        for (i = 1; i < num_sensors; i++) {
                hw->nvm.ops.read(hw, (ets_offset + i), 1, &ets_sensor);
                sensor_index = ((ets_sensor & NVM_ETS_DATA_INDEX_MASK) >>
                                NVM_ETS_DATA_INDEX_SHIFT);
                sensor_location = ((ets_sensor & NVM_ETS_DATA_LOC_MASK) >>
                                   NVM_ETS_DATA_LOC_SHIFT);

                if (sensor_location != 0)
                        hw->phy.ops.read_i2c_byte(hw,
                                        e1000_emc_temp_data[sensor_index],
                                        E1000_I2C_THERMAL_SENSOR_ADDR,
                                        &data->sensor[i].temp);
        }
        return 0;
}

/**
 *  igb_init_thermal_sensor_thresh_generic - Sets thermal sensor thresholds
 *  @hw: pointer to hardware structure
 *
 *  Sets the thermal sensor thresholds according to the NVM map
 *  and save off the threshold and location values into mac.thermal_sensor_data
 **/
static s32 igb_init_thermal_sensor_thresh_generic(struct e1000_hw *hw)
{
        u16 ets_offset;
        u16 ets_cfg;
        u16 ets_sensor;
        u8  low_thresh_delta;
        u8  num_sensors;
        u8  sensor_index;
        u8  sensor_location;
        u8  therm_limit;
        u8  i;
        struct e1000_thermal_sensor_data *data = &hw->mac.thermal_sensor_data;

        if ((hw->mac.type != e1000_i350) || (hw->bus.func != 0))
                return E1000_NOT_IMPLEMENTED;

        memset(data, 0, sizeof(struct e1000_thermal_sensor_data));

        data->sensor[0].location = 0x1;
        data->sensor[0].caution_thresh =
                (rd32(E1000_THHIGHTC) & 0xFF);
        data->sensor[0].max_op_thresh =
                (rd32(E1000_THLOWTC) & 0xFF);

        /* Return the internal sensor only if ETS is unsupported */
        hw->nvm.ops.read(hw, NVM_ETS_CFG, 1, &ets_offset);
        if ((ets_offset == 0x0000) || (ets_offset == 0xFFFF))
                return 0;

        hw->nvm.ops.read(hw, ets_offset, 1, &ets_cfg);
        if (((ets_cfg & NVM_ETS_TYPE_MASK) >> NVM_ETS_TYPE_SHIFT)
            != NVM_ETS_TYPE_EMC)
                return E1000_NOT_IMPLEMENTED;

        low_thresh_delta = ((ets_cfg & NVM_ETS_LTHRES_DELTA_MASK) >>
                            NVM_ETS_LTHRES_DELTA_SHIFT);
        num_sensors = (ets_cfg & NVM_ETS_NUM_SENSORS_MASK);

        for (i = 1; i <= num_sensors; i++) {
                hw->nvm.ops.read(hw, (ets_offset + i), 1, &ets_sensor);
                sensor_index = ((ets_sensor & NVM_ETS_DATA_INDEX_MASK) >>
                                NVM_ETS_DATA_INDEX_SHIFT);
                sensor_location = ((ets_sensor & NVM_ETS_DATA_LOC_MASK) >>
                                   NVM_ETS_DATA_LOC_SHIFT);
                therm_limit = ets_sensor & NVM_ETS_DATA_HTHRESH_MASK;

                hw->phy.ops.write_i2c_byte(hw,
                        e1000_emc_therm_limit[sensor_index],
                        E1000_I2C_THERMAL_SENSOR_ADDR,
                        therm_limit);

                if ((i < E1000_MAX_SENSORS) && (sensor_location != 0)) {
                        data->sensor[i].location = sensor_location;
                        data->sensor[i].caution_thresh = therm_limit;
                        data->sensor[i].max_op_thresh = therm_limit -
                                                        low_thresh_delta;
                }
        }
        return 0;
}

#endif
static struct e1000_mac_operations e1000_mac_ops_82575 = {
        .init_hw              = igb_init_hw_82575,
        .check_for_link       = igb_check_for_link_82575,
        .rar_set              = igb_rar_set,
        .read_mac_addr        = igb_read_mac_addr_82575,
        .get_speed_and_duplex = igb_get_link_up_info_82575,
#ifdef CONFIG_IGB_HWMON
        .get_thermal_sensor_data = igb_get_thermal_sensor_data_generic,
        .init_thermal_sensor_thresh = igb_init_thermal_sensor_thresh_generic,
#endif
};

static const struct e1000_phy_operations e1000_phy_ops_82575 = {
        .acquire              = igb_acquire_phy_82575,
        .get_cfg_done         = igb_get_cfg_done_82575,
        .release              = igb_release_phy_82575,
        .write_i2c_byte       = igb_write_i2c_byte,
        .read_i2c_byte        = igb_read_i2c_byte,
};

static struct e1000_nvm_operations e1000_nvm_ops_82575 = {
        .acquire              = igb_acquire_nvm_82575,
        .read                 = igb_read_nvm_eerd,
        .release              = igb_release_nvm_82575,
        .write                = igb_write_nvm_spi,
};

const struct e1000_info e1000_82575_info = {
        .get_invariants = igb_get_invariants_82575,
        .mac_ops = &e1000_mac_ops_82575,
        .phy_ops = &e1000_phy_ops_82575,
        .nvm_ops = &e1000_nvm_ops_82575,
};