/* SPDX-License-Identifier: GPL-2.0 */
/*
 * ChromeOS Embedded Controller protocol interface.
 *
 * Copyright (C) 2012 Google, Inc
 */

#ifndef __LINUX_CROS_EC_PROTO_H
#define __LINUX_CROS_EC_PROTO_H

#include <linux/device.h>
#include <linux/mutex.h>
#include <linux/notifier.h>

#include <linux/platform_data/cros_ec_commands.h>

#define CROS_EC_DEV_NAME        "cros_ec"
#define CROS_EC_DEV_FP_NAME     "cros_fp"
#define CROS_EC_DEV_ISH_NAME    "cros_ish"
#define CROS_EC_DEV_PD_NAME     "cros_pd"
#define CROS_EC_DEV_SCP_NAME    "cros_scp"
#define CROS_EC_DEV_TP_NAME     "cros_tp"

/*
 * The EC is unresponsive for a time after a reboot command.  Add a
 * simple delay to make sure that the bus stays locked.
 */
#define EC_REBOOT_DELAY_MS              50

/*
 * Max bus-specific overhead incurred by request/responses.
 * I2C requires 1 additional byte for requests.
 * I2C requires 2 additional bytes for responses.
 * SPI requires up to 32 additional bytes for responses.
 */
#define EC_PROTO_VERSION_UNKNOWN        0
#define EC_MAX_REQUEST_OVERHEAD         1
#define EC_MAX_RESPONSE_OVERHEAD        32

/*
 * Command interface between EC and AP, for LPC, I2C and SPI interfaces.
 */
enum {
        EC_MSG_TX_HEADER_BYTES  = 3,
        EC_MSG_TX_TRAILER_BYTES = 1,
        EC_MSG_TX_PROTO_BYTES   = EC_MSG_TX_HEADER_BYTES +
                                  EC_MSG_TX_TRAILER_BYTES,
        EC_MSG_RX_PROTO_BYTES   = 3,

        /* Max length of messages for proto 2*/
        EC_PROTO2_MSG_BYTES     = EC_PROTO2_MAX_PARAM_SIZE +
                                  EC_MSG_TX_PROTO_BYTES,

        EC_MAX_MSG_BYTES        = 64 * 1024,
};

/**
 * struct cros_ec_command - Information about a ChromeOS EC command.
 * @version: Command version number (often 0).
 * @command: Command to send (EC_CMD_...).
 * @outsize: Outgoing length in bytes.
 * @insize: Max number of bytes to accept from the EC.
 * @result: EC's response to the command (separate from communication failure).
 * @data: Where to put the incoming data from EC and outgoing data to EC.
 */
struct cros_ec_command {
        uint32_t version;
        uint32_t command;
        uint32_t outsize;
        uint32_t insize;
        uint32_t result;
        uint8_t data[0];
};

/**
 * struct cros_ec_device - Information about a ChromeOS EC device.
 * @phys_name: Name of physical comms layer (e.g. 'i2c-4').
 * @dev: Device pointer for physical comms device
 * @was_wake_device: True if this device was set to wake the system from
 *                   sleep at the last suspend.
 * @cros_class: The class structure for this device.
 * @cmd_readmem: Direct read of the EC memory-mapped region, if supported.
 *     @offset: Is within EC_LPC_ADDR_MEMMAP region.
 *     @bytes: Number of bytes to read. zero means "read a string" (including
 *             the trailing '\0'). At most only EC_MEMMAP_SIZE bytes can be
 *             read. Caller must ensure that the buffer is large enough for the
 *             result when reading a string.
 * @max_request: Max size of message requested.
 * @max_response: Max size of message response.
 * @max_passthru: Max sice of passthru message.
 * @proto_version: The protocol version used for this device.
 * @priv: Private data.
 * @irq: Interrupt to use.
 * @id: Device id.
 * @din: Input buffer (for data from EC). This buffer will always be
 *       dword-aligned and include enough space for up to 7 word-alignment
 *       bytes also, so we can ensure that the body of the message is always
 *       dword-aligned (64-bit). We use this alignment to keep ARM and x86
 *       happy. Probably word alignment would be OK, there might be a small
 *       performance advantage to using dword.
 * @dout: Output buffer (for data to EC). This buffer will always be
 *        dword-aligned and include enough space for up to 7 word-alignment
 *        bytes also, so we can ensure that the body of the message is always
 *        dword-aligned (64-bit). We use this alignment to keep ARM and x86
 *        happy. Probably word alignment would be OK, there might be a small
 *        performance advantage to using dword.
 * @din_size: Size of din buffer to allocate (zero to use static din).
 * @dout_size: Size of dout buffer to allocate (zero to use static dout).
 * @wake_enabled: True if this device can wake the system from sleep.
 * @suspended: True if this device had been suspended.
 * @cmd_xfer: Send command to EC and get response.
 *            Returns the number of bytes received if the communication
 *            succeeded, but that doesn't mean the EC was happy with the
 *            command. The caller should check msg.result for the EC's result
 *            code.
 * @pkt_xfer: Send packet to EC and get response.
 * @lock: One transaction at a time.
 * @mkbp_event_supported: True if this EC supports the MKBP event protocol.
 * @host_sleep_v1: True if this EC supports the sleep v1 command.
 * @event_notifier: Interrupt event notifier for transport devices.
 * @event_data: Raw payload transferred with the MKBP event.
 * @event_size: Size in bytes of the event data.
 * @host_event_wake_mask: Mask of host events that cause wake from suspend.
 * @ec: The platform_device used by the mfd driver to interface with the
 *      main EC.
 * @pd: The platform_device used by the mfd driver to interface with the
 *      PD behind an EC.
 */
struct cros_ec_device {
        /* These are used by other drivers that want to talk to the EC */
        const char *phys_name;
        struct device *dev;
        bool was_wake_device;
        struct class *cros_class;
        int (*cmd_readmem)(struct cros_ec_device *ec, unsigned int offset,
                           unsigned int bytes, void *dest);

        /* These are used to implement the platform-specific interface */
        u16 max_request;
        u16 max_response;
        u16 max_passthru;
        u16 proto_version;
        void *priv;
        int irq;
        u8 *din;
        u8 *dout;
        int din_size;
        int dout_size;
        bool wake_enabled;
        bool suspended;
        int (*cmd_xfer)(struct cros_ec_device *ec,
                        struct cros_ec_command *msg);
        int (*pkt_xfer)(struct cros_ec_device *ec,
                        struct cros_ec_command *msg);
        struct mutex lock;
        bool mkbp_event_supported;
        bool host_sleep_v1;
        struct blocking_notifier_head event_notifier;

        struct ec_response_get_next_event_v1 event_data;
        int event_size;
        u32 host_event_wake_mask;
        u32 last_resume_result;

        /* The platform devices used by the mfd driver */
        struct platform_device *ec;
        struct platform_device *pd;
};

/**
 * struct cros_ec_sensor_platform - ChromeOS EC sensor platform information.
 * @sensor_num: Id of the sensor, as reported by the EC.
 */
struct cros_ec_sensor_platform {
        u8 sensor_num;
};

/**
 * struct cros_ec_platform - ChromeOS EC platform information.
 * @ec_name: Name of EC device (e.g. 'cros-ec', 'cros-pd', ...)
 *           used in /dev/ and sysfs.
 * @cmd_offset: Offset to apply for each command. Set when
 *              registering a device behind another one.
 */
struct cros_ec_platform {
        const char *ec_name;
        u16 cmd_offset;
};

/**
 * cros_ec_suspend() - Handle a suspend operation for the ChromeOS EC device.
 * @ec_dev: Device to suspend.
 *
 * This can be called by drivers to handle a suspend event.
 *
 * Return: 0 on success or negative error code.
 */
int cros_ec_suspend(struct cros_ec_device *ec_dev);

/**
 * cros_ec_resume() - Handle a resume operation for the ChromeOS EC device.
 * @ec_dev: Device to resume.
 *
 * This can be called by drivers to handle a resume event.
 *
 * Return: 0 on success or negative error code.
 */
int cros_ec_resume(struct cros_ec_device *ec_dev);

/**
 * cros_ec_prepare_tx() - Prepare an outgoing message in the output buffer.
 * @ec_dev: Device to register.
 * @msg: Message to write.
 *
 * This is intended to be used by all ChromeOS EC drivers, but at present
 * only SPI uses it. Once LPC uses the same protocol it can start using it.
 * I2C could use it now, with a refactor of the existing code.
 *
 * Return: 0 on success or negative error code.
 */
int cros_ec_prepare_tx(struct cros_ec_device *ec_dev,
                       struct cros_ec_command *msg);

/**
 * cros_ec_check_result() - Check ec_msg->result.
 * @ec_dev: EC device.
 * @msg: Message to check.
 *
 * This is used by ChromeOS EC drivers to check the ec_msg->result for
 * errors and to warn about them.
 *
 * Return: 0 on success or negative error code.
 */
int cros_ec_check_result(struct cros_ec_device *ec_dev,
                         struct cros_ec_command *msg);

/**
 * cros_ec_cmd_xfer() - Send a command to the ChromeOS EC.
 * @ec_dev: EC device.
 * @msg: Message to write.
 *
 * Call this to send a command to the ChromeOS EC.  This should be used
 * instead of calling the EC's cmd_xfer() callback directly.
 *
 * Return: 0 on success or negative error code.
 */
int cros_ec_cmd_xfer(struct cros_ec_device *ec_dev,
                     struct cros_ec_command *msg);

/**
 * cros_ec_cmd_xfer_status() - Send a command to the ChromeOS EC.
 * @ec_dev: EC device.
 * @msg: Message to write.
 *
 * This function is identical to cros_ec_cmd_xfer, except it returns success
 * status only if both the command was transmitted successfully and the EC
 * replied with success status. It's not necessary to check msg->result when
 * using this function.
 *
 * Return: The number of bytes transferred on success or negative error code.
 */
int cros_ec_cmd_xfer_status(struct cros_ec_device *ec_dev,
                            struct cros_ec_command *msg);

/**
 * cros_ec_register() - Register a new ChromeOS EC, using the provided info.
 * @ec_dev: Device to register.
 *
 * Before calling this, allocate a pointer to a new device and then fill
 * in all the fields up to the --private-- marker.
 *
 * Return: 0 on success or negative error code.
 */
int cros_ec_register(struct cros_ec_device *ec_dev);

/**
 * cros_ec_unregister() - Remove a ChromeOS EC.
 * @ec_dev: Device to unregister.
 *
 * Call this to deregister a ChromeOS EC, then clean up any private data.
 *
 * Return: 0 on success or negative error code.
 */
int cros_ec_unregister(struct cros_ec_device *ec_dev);

/**
 * cros_ec_query_all() -  Query the protocol version supported by the
 *         ChromeOS EC.
 * @ec_dev: Device to register.
 *
 * Return: 0 on success or negative error code.
 */
int cros_ec_query_all(struct cros_ec_device *ec_dev);

/**
 * cros_ec_get_next_event() - Fetch next event from the ChromeOS EC.
 * @ec_dev: Device to fetch event from.
 * @wake_event: Pointer to a bool set to true upon return if the event might be
 *              treated as a wake event. Ignored if null.
 *
 * Return: negative error code on errors; 0 for no data; or else number of
 * bytes received (i.e., an event was retrieved successfully). Event types are
 * written out to @ec_dev->event_data.event_type on success.
 */
int cros_ec_get_next_event(struct cros_ec_device *ec_dev, bool *wake_event);

/**
 * cros_ec_get_host_event() - Return a mask of event set by the ChromeOS EC.
 * @ec_dev: Device to fetch event from.
 *
 * When MKBP is supported, when the EC raises an interrupt, we collect the
 * events raised and call the functions in the ec notifier. This function
 * is a helper to know which events are raised.
 *
 * Return: 0 on error or non-zero bitmask of one or more EC_HOST_EVENT_*.
 */
u32 cros_ec_get_host_event(struct cros_ec_device *ec_dev);

#endif /* __LINUX_CROS_EC_PROTO_H */