LXR linux/drivers/net/hamradio/baycom

   1// SPDX-License-Identifier: GPL-2.0-or-later
   2/*****************************************************************************/
   3
   4/*
   5 *      baycom_par.c  -- baycom par96 and picpar radio modem driver.
   6 *
   7 *      Copyright (C) 1996-2000  Thomas Sailer (sailer@ife.ee.ethz.ch)
   8 *
   9 *  Please note that the GPL allows you to use the driver, NOT the radio.
  10 *  In order to use the radio, you need a license from the communications
  11 *  authority of your country.
  12 *
  13 *  Supported modems
  14 *
  15 *  par96:  This is a modem for 9600 baud FSK compatible to the G3RUH standard.
  16 *          The modem does all the filtering and regenerates the receiver clock.
  17 *          Data is transferred from and to the PC via a shift register.
  18 *          The shift register is filled with 16 bits and an interrupt is
  19 *          signalled. The PC then empties the shift register in a burst. This
  20 *          modem connects to the parallel port, hence the name. The modem
  21 *          leaves the implementation of the HDLC protocol and the scrambler
  22 *          polynomial to the PC. This modem is no longer available (at least
  23 *          from Baycom) and has been replaced by the PICPAR modem (see below).
  24 *          You may however still build one from the schematics published in
  25 *          cq-DL :-).
  26 *
  27 *  picpar: This is a redesign of the par96 modem by Henning Rech, DF9IC. The
  28 *          modem is protocol compatible to par96, but uses only three low
  29 *          power ICs and can therefore be fed from the parallel port and
  30 *          does not require an additional power supply. It features
  31 *          built in DCD circuitry. The driver should therefore be configured
  32 *          for hardware DCD.
  33 *
  34 *  Command line options (insmod command line)
  35 *
  36 *  mode     driver mode string. Valid choices are par96 and picpar.
  37 *  iobase   base address of the port; common values are 0x378, 0x278, 0x3bc
  38 *
  39 *  History:
  40 *   0.1  26.06.1996  Adapted from baycom.c and made network driver interface
  41 *        18.10.1996  Changed to new user space access routines (copy_{to,from}_user)
  42 *   0.3  26.04.1997  init code/data tagged
  43 *   0.4  08.07.1997  alternative ser12 decoding algorithm (uses delta CTS ints)
  44 *   0.5  11.11.1997  split into separate files for ser12/par96
  45 *   0.6  03.08.1999  adapt to Linus' new __setup/__initcall
  46 *                    removed some pre-2.2 kernel compatibility cruft
  47 *   0.7  10.08.1999  Check if parport can do SPP and is safe to access during interrupt contexts
  48 *   0.8  12.02.2000  adapted to softnet driver interface
  49 *                    removed direct parport access, uses parport driver methods
  50 *   0.9  03.07.2000  fix interface name handling
  51 */
  52
  53/*****************************************************************************/
  54
  55#include <linux/module.h>
  56#include <linux/kernel.h>
  57#include <linux/types.h>
  58#include <linux/fcntl.h>
  59#include <linux/interrupt.h>
  60#include <linux/ioport.h>
  61#include <linux/in.h>
  62#include <linux/string.h>
  63#include <linux/init.h>
  64#include <linux/delay.h>
  65#include <linux/errno.h>
  66#include <linux/netdevice.h>
  67#include <linux/hdlcdrv.h>
  68#include <linux/baycom.h>
  69#include <linux/parport.h>
  70#include <linux/bitops.h>
  71#include <linux/jiffies.h>
  72
  73#include <linux/uaccess.h>
  74
  75/* --------------------------------------------------------------------- */
  76
  77#define BAYCOM_DEBUG
  78
  79/*
  80 * modem options; bit mask
  81 */
  82#define BAYCOM_OPTIONS_SOFTDCD  1
  83
  84/* --------------------------------------------------------------------- */
  85
  86static const char bc_drvname[] = "baycom_par";
  87static const char bc_drvinfo[] = KERN_INFO "baycom_par: (C) 1996-2000 Thomas Sailer, HB9JNX/AE4WA\n"
  88"baycom_par: version 0.9\n";
  89
  90/* --------------------------------------------------------------------- */
  91
  92#define NR_PORTS 4
  93
  94static struct net_device *baycom_device[NR_PORTS];
  95
  96/* --------------------------------------------------------------------- */
  97
  98#define PAR96_BURSTBITS 16
  99#define PAR96_BURST     4
 100#define PAR96_PTT       2
 101#define PAR96_TXBIT     1
 102#define PAR96_ACK       0x40
 103#define PAR96_RXBIT     0x20
 104#define PAR96_DCD       0x10
 105#define PAR97_POWER     0xf8
 106
 107/* ---------------------------------------------------------------------- */
 108/*
 109 * Information that need to be kept for each board.
 110 */
 111
 112struct baycom_state {
 113        struct hdlcdrv_state hdrv;
 114
 115        struct pardevice *pdev;
 116        unsigned int options;
 117
 118        struct modem_state {
 119                short arb_divider;
 120                unsigned char flags;
 121                unsigned int shreg;
 122                struct modem_state_par96 {
 123                        int dcd_count;
 124                        unsigned int dcd_shreg;
 125                        unsigned long descram;
 126                        unsigned long scram;
 127                } par96;
 128        } modem;
 129
 130#ifdef BAYCOM_DEBUG
 131        struct debug_vals {
 132                unsigned long last_jiffies;
 133                unsigned cur_intcnt;
 134                unsigned last_intcnt;
 135                int cur_pllcorr;
 136                int last_pllcorr;
 137        } debug_vals;
 138#endif /* BAYCOM_DEBUG */
 139};
 140
 141/* --------------------------------------------------------------------- */
 142
 143static inline void baycom_int_freq(struct baycom_state *bc)
 144{
 145#ifdef BAYCOM_DEBUG
 146        unsigned long cur_jiffies = jiffies;
 147        /*
 148         * measure the interrupt frequency
 149         */
 150        bc->debug_vals.cur_intcnt++;
 151        if (time_after_eq(cur_jiffies, bc->debug_vals.last_jiffies + HZ)) {
 152                bc->debug_vals.last_jiffies = cur_jiffies;
 153                bc->debug_vals.last_intcnt = bc->debug_vals.cur_intcnt;
 154                bc->debug_vals.cur_intcnt = 0;
 155                bc->debug_vals.last_pllcorr = bc->debug_vals.cur_pllcorr;
 156                bc->debug_vals.cur_pllcorr = 0;
 157        }
 158#endif /* BAYCOM_DEBUG */
 159}
 160
 161/* --------------------------------------------------------------------- */
 162/*
 163 * ===================== PAR96 specific routines =========================
 164 */
 165
 166#define PAR96_DESCRAM_TAP1 0x20000
 167#define PAR96_DESCRAM_TAP2 0x01000
 168#define PAR96_DESCRAM_TAP3 0x00001
 169
 170#define PAR96_DESCRAM_TAPSH1 17
 171#define PAR96_DESCRAM_TAPSH2 12
 172#define PAR96_DESCRAM_TAPSH3 0
 173
 174#define PAR96_SCRAM_TAP1 0x20000 /* X^17 */
 175#define PAR96_SCRAM_TAPN 0x00021 /* X^0+X^5 */
 176
 177/* --------------------------------------------------------------------- */
 178
 179static inline void par96_tx(struct net_device *dev, struct baycom_state *bc)
 180{
 181        int i;
 182        unsigned int data = hdlcdrv_getbits(&bc->hdrv);
 183        struct parport *pp = bc->pdev->port;
 184
 185        for(i = 0; i < PAR96_BURSTBITS; i++, data >>= 1) {
 186                unsigned char val = PAR97_POWER;
 187                bc->modem.par96.scram = ((bc->modem.par96.scram << 1) |
 188                                         (bc->modem.par96.scram & 1));
 189                if (!(data & 1))
 190                        bc->modem.par96.scram ^= 1;
 191                if (bc->modem.par96.scram & (PAR96_SCRAM_TAP1 << 1))
 192                        bc->modem.par96.scram ^=
 193                                (PAR96_SCRAM_TAPN << 1);
 194                if (bc->modem.par96.scram & (PAR96_SCRAM_TAP1 << 2))
 195                        val |= PAR96_TXBIT;
 196                pp->ops->write_data(pp, val);
 197                pp->ops->write_data(pp, val | PAR96_BURST);
 198        }
 199}
 200
 201/* --------------------------------------------------------------------- */
 202
 203static inline void par96_rx(struct net_device *dev, struct baycom_state *bc)
 204{
 205        int i;
 206        unsigned int data, mask, mask2, descx;
 207        struct parport *pp = bc->pdev->port;
 208
 209        /*
 210         * do receiver; differential decode and descramble on the fly
 211         */
 212        for(data = i = 0; i < PAR96_BURSTBITS; i++) {
 213                bc->modem.par96.descram = (bc->modem.par96.descram << 1);
 214                if (pp->ops->read_status(pp) & PAR96_RXBIT)
 215                        bc->modem.par96.descram |= 1;
 216                descx = bc->modem.par96.descram ^
 217                        (bc->modem.par96.descram >> 1);
 218                /* now the diff decoded data is inverted in descram */
 219                pp->ops->write_data(pp, PAR97_POWER | PAR96_PTT);
 220                descx ^= ((descx >> PAR96_DESCRAM_TAPSH1) ^
 221                          (descx >> PAR96_DESCRAM_TAPSH2));
 222                data >>= 1;
 223                if (!(descx & 1))
 224                        data |= 0x8000;
 225                pp->ops->write_data(pp, PAR97_POWER | PAR96_PTT | PAR96_BURST);
 226        }
 227        hdlcdrv_putbits(&bc->hdrv, data);
 228        /*
 229         * do DCD algorithm
 230         */
 231        if (bc->options & BAYCOM_OPTIONS_SOFTDCD) {
 232                bc->modem.par96.dcd_shreg = (bc->modem.par96.dcd_shreg >> 16)
 233                        | (data << 16);
 234                /* search for flags and set the dcd counter appropriately */
 235                for(mask = 0x1fe00, mask2 = 0xfc00, i = 0;
 236                    i < PAR96_BURSTBITS; i++, mask <<= 1, mask2 <<= 1)
 237                        if ((bc->modem.par96.dcd_shreg & mask) == mask2)
 238                                bc->modem.par96.dcd_count = HDLCDRV_MAXFLEN+4;
 239                /* check for abort/noise sequences */
 240                for(mask = 0x1fe00, mask2 = 0x1fe00, i = 0;
 241                    i < PAR96_BURSTBITS; i++, mask <<= 1, mask2 <<= 1)
 242                        if (((bc->modem.par96.dcd_shreg & mask) == mask2) &&
 243                            (bc->modem.par96.dcd_count >= 0))
 244                                bc->modem.par96.dcd_count -= HDLCDRV_MAXFLEN-10;
 245                /* decrement and set the dcd variable */
 246                if (bc->modem.par96.dcd_count >= 0)
 247                        bc->modem.par96.dcd_count -= 2;
 248                hdlcdrv_setdcd(&bc->hdrv, bc->modem.par96.dcd_count > 0);
 249        } else {
 250                hdlcdrv_setdcd(&bc->hdrv, !!(pp->ops->read_status(pp) & PAR96_DCD));
 251        }
 252}
 253
 254/* --------------------------------------------------------------------- */
 255
 256static void par96_interrupt(void *dev_id)
 257{
 258        struct net_device *dev = dev_id;
 259        struct baycom_state *bc = netdev_priv(dev);
 260
 261        baycom_int_freq(bc);
 262        /*
 263         * check if transmitter active
 264         */
 265        if (hdlcdrv_ptt(&bc->hdrv))
 266                par96_tx(dev, bc);
 267        else {
 268                par96_rx(dev, bc);
 269                if (--bc->modem.arb_divider <= 0) {
 270                        bc->modem.arb_divider = 6;
 271                        local_irq_enable();
 272                        hdlcdrv_arbitrate(dev, &bc->hdrv);
 273                }
 274        }
 275        local_irq_enable();
 276        hdlcdrv_transmitter(dev, &bc->hdrv);
 277        hdlcdrv_receiver(dev, &bc->hdrv);
 278        local_irq_disable();
 279}
 280
 281/* --------------------------------------------------------------------- */
 282
 283static void par96_wakeup(void *handle)
 284{
 285        struct net_device *dev = (struct net_device *)handle;
 286        struct baycom_state *bc = netdev_priv(dev);
 287
 288        printk(KERN_DEBUG "baycom_par: %s: why am I being woken up?\n", dev->name);
 289        if (!parport_claim(bc->pdev))
 290                printk(KERN_DEBUG "baycom_par: %s: I'm broken.\n", dev->name);
 291}
 292
 293/* --------------------------------------------------------------------- */
 294
 295static int par96_open(struct net_device *dev)
 296{
 297        struct baycom_state *bc = netdev_priv(dev);
 298        struct pardev_cb par_cb;
 299        struct parport *pp;
 300        int i;
 301
 302        if (!dev || !bc)
 303                return -ENXIO;
 304        pp = parport_find_base(dev->base_addr);
 305        if (!pp) {
 306                printk(KERN_ERR "baycom_par: parport at 0x%lx unknown\n", dev->base_addr);
 307                return -ENXIO;
 308        }
 309        if (pp->irq < 0) {
 310                printk(KERN_ERR "baycom_par: parport at 0x%lx has no irq\n", pp->base);
 311                parport_put_port(pp);
 312                return -ENXIO;
 313        }
 314        if ((~pp->modes) & (PARPORT_MODE_PCSPP | PARPORT_MODE_SAFEININT)) {
 315                printk(KERN_ERR "baycom_par: parport at 0x%lx cannot be used\n", pp->base);
 316                parport_put_port(pp);
 317                return -ENXIO;
 318        }
 319        memset(&bc->modem, 0, sizeof(bc->modem));
 320        bc->hdrv.par.bitrate = 9600;
 321        memset(&par_cb, 0, sizeof(par_cb));
 322        par_cb.wakeup = par96_wakeup;
 323        par_cb.irq_func = par96_interrupt;
 324        par_cb.private = (void *)dev;
 325        par_cb.flags = PARPORT_DEV_EXCL;
 326        for (i = 0; i < NR_PORTS; i++)
 327                if (baycom_device[i] == dev)
 328                        break;
 329
 330        if (i == NR_PORTS) {
 331                pr_err("%s: no device found\n", bc_drvname);
 332                parport_put_port(pp);
 333                return -ENODEV;
 334        }
 335        bc->pdev = parport_register_dev_model(pp, dev->name, &par_cb, i);
 336        parport_put_port(pp);
 337        if (!bc->pdev) {
 338                printk(KERN_ERR "baycom_par: cannot register parport at 0x%lx\n", dev->base_addr);
 339                return -ENXIO;
 340        }
 341        if (parport_claim(bc->pdev)) {
 342                printk(KERN_ERR "baycom_par: parport at 0x%lx busy\n", pp->base);
 343                parport_unregister_device(bc->pdev);
 344                return -EBUSY;
 345        }
 346        pp = bc->pdev->port;
 347        dev->irq = pp->irq;
 348        pp->ops->data_forward(pp);
 349        bc->hdrv.par.bitrate = 9600;
 350        pp->ops->write_data(pp, PAR96_PTT | PAR97_POWER); /* switch off PTT */
 351        pp->ops->enable_irq(pp);
 352        printk(KERN_INFO "%s: par96 at iobase 0x%lx irq %u options 0x%x\n",
 353               bc_drvname, dev->base_addr, dev->irq, bc->options);
 354        return 0;
 355}
 356
 357/* --------------------------------------------------------------------- */
 358
 359static int par96_close(struct net_device *dev)
 360{
 361        struct baycom_state *bc = netdev_priv(dev);
 362        struct parport *pp;
 363
 364        if (!dev || !bc)
 365                return -EINVAL;
 366        pp = bc->pdev->port;
 367        /* disable interrupt */
 368        pp->ops->disable_irq(pp);
 369        /* switch off PTT */
 370        pp->ops->write_data(pp, PAR96_PTT | PAR97_POWER);
 371        parport_release(bc->pdev);
 372        parport_unregister_device(bc->pdev);
 373        printk(KERN_INFO "%s: close par96 at iobase 0x%lx irq %u\n",
 374               bc_drvname, dev->base_addr, dev->irq);
 375        return 0;
 376}
 377
 378/* --------------------------------------------------------------------- */
 379/*
 380 * ===================== hdlcdrv driver interface =========================
 381 */
 382
 383static int baycom_ioctl(struct net_device *dev, struct ifreq *ifr,
 384                        struct hdlcdrv_ioctl *hi, int cmd);
 385
 386/* --------------------------------------------------------------------- */
 387
 388static const struct hdlcdrv_ops par96_ops = {
 389        .drvname = bc_drvname,
 390        .drvinfo = bc_drvinfo,
 391        .open    = par96_open,
 392        .close   = par96_close,
 393        .ioctl   = baycom_ioctl
 394};
 395
 396/* --------------------------------------------------------------------- */
 397
 398static int baycom_setmode(struct baycom_state *bc, const char *modestr)
 399{
 400        if (!strncmp(modestr, "picpar", 6))
 401                bc->options = 0;
 402        else if (!strncmp(modestr, "par96", 5))
 403                bc->options = BAYCOM_OPTIONS_SOFTDCD;
 404        else
 405                bc->options = !!strchr(modestr, '*');
 406        return 0;
 407}
 408
 409/* --------------------------------------------------------------------- */
 410
 411static int baycom_ioctl(struct net_device *dev, struct ifreq *ifr,
 412                        struct hdlcdrv_ioctl *hi, int cmd)
 413{
 414        struct baycom_state *bc;
 415        struct baycom_ioctl bi;
 416
 417        if (!dev)
 418                return -EINVAL;
 419
 420        bc = netdev_priv(dev);
 421        BUG_ON(bc->hdrv.magic != HDLCDRV_MAGIC);
 422
 423        if (cmd != SIOCDEVPRIVATE)
 424                return -ENOIOCTLCMD;
 425        switch (hi->cmd) {
 426        default:
 427                break;
 428
 429        case HDLCDRVCTL_GETMODE:
 430                strcpy(hi->data.modename, bc->options ? "par96" : "picpar");
 431                if (copy_to_user(ifr->ifr_data, hi, sizeof(struct hdlcdrv_ioctl)))
 432                        return -EFAULT;
 433                return 0;
 434
 435        case HDLCDRVCTL_SETMODE:
 436                if (netif_running(dev) || !capable(CAP_NET_ADMIN))
 437                        return -EACCES;
 438                hi->data.modename[sizeof(hi->data.modename)-1] = '\0';
 439                return baycom_setmode(bc, hi->data.modename);
 440
 441        case HDLCDRVCTL_MODELIST:
 442                strcpy(hi->data.modename, "par96,picpar");
 443                if (copy_to_user(ifr->ifr_data, hi, sizeof(struct hdlcdrv_ioctl)))
 444                        return -EFAULT;
 445                return 0;
 446
 447        case HDLCDRVCTL_MODEMPARMASK:
 448                return HDLCDRV_PARMASK_IOBASE;
 449
 450        }
 451
 452        if (copy_from_user(&bi, ifr->ifr_data, sizeof(bi)))
 453                return -EFAULT;
 454        switch (bi.cmd) {
 455        default:
 456                return -ENOIOCTLCMD;
 457
 458#ifdef BAYCOM_DEBUG
 459        case BAYCOMCTL_GETDEBUG:
 460                bi.data.dbg.debug1 = bc->hdrv.ptt_keyed;
 461                bi.data.dbg.debug2 = bc->debug_vals.last_intcnt;
 462                bi.data.dbg.debug3 = bc->debug_vals.last_pllcorr;
 463                break;
 464#endif /* BAYCOM_DEBUG */
 465
 466        }
 467        if (copy_to_user(ifr->ifr_data, &bi, sizeof(bi)))
 468                return -EFAULT;
 469        return 0;
 470
 471}
 472
 473/* --------------------------------------------------------------------- */
 474
 475/*
 476 * command line settable parameters
 477 */
 478static char *mode[NR_PORTS] = { "picpar", };
 479static int iobase[NR_PORTS] = { 0x378, };
 480
 481module_param_array(mode, charp, NULL, 0);
 482MODULE_PARM_DESC(mode, "baycom operating mode; eg. par96 or picpar");
 483module_param_hw_array(iobase, int, ioport, NULL, 0);
 484MODULE_PARM_DESC(iobase, "baycom io base address");
 485
 486MODULE_AUTHOR("Thomas M. Sailer, sailer@ife.ee.ethz.ch, hb9jnx@hb9w.che.eu");
 487MODULE_DESCRIPTION("Baycom par96 and picpar amateur radio modem driver");
 488MODULE_LICENSE("GPL");
 489
 490/* --------------------------------------------------------------------- */
 491
 492static int baycom_par_probe(struct pardevice *par_dev)
 493{
 494        struct device_driver *drv = par_dev->dev.driver;
 495        int len = strlen(drv->name);
 496
 497        if (strncmp(par_dev->name, drv->name, len))
 498                return -ENODEV;
 499
 500        return 0;
 501}
 502
 503static struct parport_driver baycom_par_driver = {
 504        .name = "bcp",
 505        .probe = baycom_par_probe,
 506        .devmodel = true,
 507};
 508
 509static int __init init_baycompar(void)
 510{
 511        int i, found = 0, ret;
 512        char set_hw = 1;
 513
 514        printk(bc_drvinfo);
 515
 516        ret = parport_register_driver(&baycom_par_driver);
 517        if (ret)
 518                return ret;
 519
 520        /*
 521         * register net devices
 522         */
 523        for (i = 0; i < NR_PORTS; i++) {
 524                struct net_device *dev;
 525                struct baycom_state *bc;
 526                char ifname[IFNAMSIZ];
 527
 528                sprintf(ifname, "bcp%d", i);
 529
 530                if (!mode[i])
 531                        set_hw = 0;
 532                if (!set_hw)
 533                        iobase[i] = 0;
 534
 535                dev = hdlcdrv_register(&par96_ops,
 536                                       sizeof(struct baycom_state),
 537                                       ifname, iobase[i], 0, 0);
 538                if (IS_ERR(dev)) 
 539                        break;
 540
 541                bc = netdev_priv(dev);
 542                if (set_hw && baycom_setmode(bc, mode[i]))
 543                        set_hw = 0;
 544                found++;
 545                baycom_device[i] = dev;
 546        }
 547
 548        if (!found) {
 549                parport_unregister_driver(&baycom_par_driver);
 550                return -ENXIO;
 551        }
 552        return 0;
 553}
 554
 555static void __exit cleanup_baycompar(void)
 556{
 557        int i;
 558
 559        for(i = 0; i < NR_PORTS; i++) {
 560                struct net_device *dev = baycom_device[i];
 561
 562                if (dev)
 563                        hdlcdrv_unregister(dev);
 564        }
 565        parport_unregister_driver(&baycom_par_driver);
 566}
 567
 568module_init(init_baycompar);
 569module_exit(cleanup_baycompar);
 570
 571/* --------------------------------------------------------------------- */
 572
 573#ifndef MODULE
 574
 575/*
 576 * format: baycom_par=io,mode
 577 * mode: par96,picpar
 578 */
 579
 580static int __init baycom_par_setup(char *str)
 581{
 582        static unsigned nr_dev;
 583        int ints[2];
 584
 585        if (nr_dev >= NR_PORTS)
 586                return 0;
 587        str = get_options(str, 2, ints);
 588        if (ints[0] < 1)
 589                return 0;
 590        mode[nr_dev] = str;
 591        iobase[nr_dev] = ints[1];
 592        nr_dev++;
 593        return 1;
 594}
 595
 596__setup("baycom_par=", baycom_par_setup);
 597
 598#endif /* MODULE */
 599/* --------------------------------------------------------------------- */
 600