// SPDX-License-Identifier: GPL-2.0-or-later
/*
 */

#include <linux/init.h>
#include <linux/slab.h>
#include <linux/usb.h>
#include <linux/usb/audio.h>
#include <linux/usb/midi.h>
#include <linux/bits.h>

#include <sound/control.h>
#include <sound/core.h>
#include <sound/info.h>
#include <sound/pcm.h>

#include "usbaudio.h"
#include "card.h"
#include "mixer.h"
#include "mixer_quirks.h"
#include "midi.h"
#include "quirks.h"
#include "helper.h"
#include "endpoint.h"
#include "pcm.h"
#include "clock.h"
#include "stream.h"

/*
 * handle the quirks for the contained interfaces
 */
static int create_composite_quirk(struct snd_usb_audio *chip,
                                  struct usb_interface *iface,
                                  struct usb_driver *driver,
                                  const struct snd_usb_audio_quirk *quirk_comp)
{
        int probed_ifnum = get_iface_desc(iface->altsetting)->bInterfaceNumber;
        const struct snd_usb_audio_quirk *quirk;
        int err;

        for (quirk = quirk_comp->data; quirk->ifnum >= 0; ++quirk) {
                iface = usb_ifnum_to_if(chip->dev, quirk->ifnum);
                if (!iface)
                        continue;
                if (quirk->ifnum != probed_ifnum &&
                    usb_interface_claimed(iface))
                        continue;
                err = snd_usb_create_quirk(chip, iface, driver, quirk);
                if (err < 0)
                        return err;
        }

        for (quirk = quirk_comp->data; quirk->ifnum >= 0; ++quirk) {
                iface = usb_ifnum_to_if(chip->dev, quirk->ifnum);
                if (!iface)
                        continue;
                if (quirk->ifnum != probed_ifnum &&
                    !usb_interface_claimed(iface))
                        usb_driver_claim_interface(driver, iface, (void *)-1L);
        }

        return 0;
}

static int ignore_interface_quirk(struct snd_usb_audio *chip,
                                  struct usb_interface *iface,
                                  struct usb_driver *driver,
                                  const struct snd_usb_audio_quirk *quirk)
{
        return 0;
}


/*
 * Allow alignment on audio sub-slot (channel samples) rather than
 * on audio slots (audio frames)
 */
static int create_align_transfer_quirk(struct snd_usb_audio *chip,
                                       struct usb_interface *iface,
                                       struct usb_driver *driver,
                                       const struct snd_usb_audio_quirk *quirk)
{
        chip->txfr_quirk = 1;
        return 1;       /* Continue with creating streams and mixer */
}

static int create_any_midi_quirk(struct snd_usb_audio *chip,
                                 struct usb_interface *intf,
                                 struct usb_driver *driver,
                                 const struct snd_usb_audio_quirk *quirk)
{
        return snd_usbmidi_create(chip->card, intf, &chip->midi_list, quirk);
}

/*
 * create a stream for an interface with proper descriptors
 */
static int create_standard_audio_quirk(struct snd_usb_audio *chip,
                                       struct usb_interface *iface,
                                       struct usb_driver *driver,
                                       const struct snd_usb_audio_quirk *quirk)
{
        struct usb_host_interface *alts;
        struct usb_interface_descriptor *altsd;
        int err;

        if (chip->usb_id == USB_ID(0x1686, 0x00dd)) /* Zoom R16/24 */
                chip->tx_length_quirk = 1;

        alts = &iface->altsetting[0];
        altsd = get_iface_desc(alts);
        err = snd_usb_parse_audio_interface(chip, altsd->bInterfaceNumber);
        if (err < 0) {
                usb_audio_err(chip, "cannot setup if %d: error %d\n",
                           altsd->bInterfaceNumber, err);
                return err;
        }
        /* reset the current interface */
        usb_set_interface(chip->dev, altsd->bInterfaceNumber, 0);
        return 0;
}

/*
 * create a stream for an endpoint/altsetting without proper descriptors
 */
static int create_fixed_stream_quirk(struct snd_usb_audio *chip,
                                     struct usb_interface *iface,
                                     struct usb_driver *driver,
                                     const struct snd_usb_audio_quirk *quirk)
{
        struct audioformat *fp;
        struct usb_host_interface *alts;
        struct usb_interface_descriptor *altsd;
        int stream, err;
        unsigned *rate_table = NULL;

        fp = kmemdup(quirk->data, sizeof(*fp), GFP_KERNEL);
        if (!fp)
                return -ENOMEM;

        INIT_LIST_HEAD(&fp->list);
        if (fp->nr_rates > MAX_NR_RATES) {
                kfree(fp);
                return -EINVAL;
        }
        if (fp->nr_rates > 0) {
                rate_table = kmemdup(fp->rate_table,
                                     sizeof(int) * fp->nr_rates, GFP_KERNEL);
                if (!rate_table) {
                        kfree(fp);
                        return -ENOMEM;
                }
                fp->rate_table = rate_table;
        }

        stream = (fp->endpoint & USB_DIR_IN)
                ? SNDRV_PCM_STREAM_CAPTURE : SNDRV_PCM_STREAM_PLAYBACK;
        err = snd_usb_add_audio_stream(chip, stream, fp);
        if (err < 0)
                goto error;
        if (fp->iface != get_iface_desc(&iface->altsetting[0])->bInterfaceNumber ||
            fp->altset_idx >= iface->num_altsetting) {
                err = -EINVAL;
                goto error;
        }
        alts = &iface->altsetting[fp->altset_idx];
        altsd = get_iface_desc(alts);
        if (altsd->bNumEndpoints < 1) {
                err = -EINVAL;
                goto error;
        }

        fp->protocol = altsd->bInterfaceProtocol;

        if (fp->datainterval == 0)
                fp->datainterval = snd_usb_parse_datainterval(chip, alts);
        if (fp->maxpacksize == 0)
                fp->maxpacksize = le16_to_cpu(get_endpoint(alts, 0)->wMaxPacketSize);
        usb_set_interface(chip->dev, fp->iface, 0);
        snd_usb_init_pitch(chip, fp->iface, alts, fp);
        snd_usb_init_sample_rate(chip, fp->iface, alts, fp, fp->rate_max);
        return 0;

 error:
        list_del(&fp->list); /* unlink for avoiding double-free */
        kfree(fp);
        kfree(rate_table);
        return err;
}

static int create_auto_pcm_quirk(struct snd_usb_audio *chip,
                                 struct usb_interface *iface,
                                 struct usb_driver *driver)
{
        struct usb_host_interface *alts;
        struct usb_interface_descriptor *altsd;
        struct usb_endpoint_descriptor *epd;
        struct uac1_as_header_descriptor *ashd;
        struct uac_format_type_i_discrete_descriptor *fmtd;

        /*
         * Most Roland/Yamaha audio streaming interfaces have more or less
         * standard descriptors, but older devices might lack descriptors, and
         * future ones might change, so ensure that we fail silently if the
         * interface doesn't look exactly right.
         */

        /* must have a non-zero altsetting for streaming */
        if (iface->num_altsetting < 2)
                return -ENODEV;
        alts = &iface->altsetting[1];
        altsd = get_iface_desc(alts);

        /* must have an isochronous endpoint for streaming */
        if (altsd->bNumEndpoints < 1)
                return -ENODEV;
        epd = get_endpoint(alts, 0);
        if (!usb_endpoint_xfer_isoc(epd))
                return -ENODEV;

        /* must have format descriptors */
        ashd = snd_usb_find_csint_desc(alts->extra, alts->extralen, NULL,
                                       UAC_AS_GENERAL);
        fmtd = snd_usb_find_csint_desc(alts->extra, alts->extralen, NULL,
                                       UAC_FORMAT_TYPE);
        if (!ashd || ashd->bLength < 7 ||
            !fmtd || fmtd->bLength < 8)
                return -ENODEV;

        return create_standard_audio_quirk(chip, iface, driver, NULL);
}

static int create_yamaha_midi_quirk(struct snd_usb_audio *chip,
                                    struct usb_interface *iface,
                                    struct usb_driver *driver,
                                    struct usb_host_interface *alts)
{
        static const struct snd_usb_audio_quirk yamaha_midi_quirk = {
                .type = QUIRK_MIDI_YAMAHA
        };
        struct usb_midi_in_jack_descriptor *injd;
        struct usb_midi_out_jack_descriptor *outjd;

        /* must have some valid jack descriptors */
        injd = snd_usb_find_csint_desc(alts->extra, alts->extralen,
                                       NULL, USB_MS_MIDI_IN_JACK);
        outjd = snd_usb_find_csint_desc(alts->extra, alts->extralen,
                                        NULL, USB_MS_MIDI_OUT_JACK);
        if (!injd && !outjd)
                return -ENODEV;
        if ((injd && !snd_usb_validate_midi_desc(injd)) ||
            (outjd && !snd_usb_validate_midi_desc(outjd)))
                return -ENODEV;
        if (injd && (injd->bLength < 5 ||
                     (injd->bJackType != USB_MS_EMBEDDED &&
                      injd->bJackType != USB_MS_EXTERNAL)))
                return -ENODEV;
        if (outjd && (outjd->bLength < 6 ||
                      (outjd->bJackType != USB_MS_EMBEDDED &&
                       outjd->bJackType != USB_MS_EXTERNAL)))
                return -ENODEV;
        return create_any_midi_quirk(chip, iface, driver, &yamaha_midi_quirk);
}

static int create_roland_midi_quirk(struct snd_usb_audio *chip,
                                    struct usb_interface *iface,
                                    struct usb_driver *driver,
                                    struct usb_host_interface *alts)
{
        static const struct snd_usb_audio_quirk roland_midi_quirk = {
                .type = QUIRK_MIDI_ROLAND
        };
        u8 *roland_desc = NULL;

        /* might have a vendor-specific descriptor <06 24 F1 02 ...> */
        for (;;) {
                roland_desc = snd_usb_find_csint_desc(alts->extra,
                                                      alts->extralen,
                                                      roland_desc, 0xf1);
                if (!roland_desc)
                        return -ENODEV;
                if (roland_desc[0] < 6 || roland_desc[3] != 2)
                        continue;
                return create_any_midi_quirk(chip, iface, driver,
                                             &roland_midi_quirk);
        }
}

static int create_std_midi_quirk(struct snd_usb_audio *chip,
                                 struct usb_interface *iface,
                                 struct usb_driver *driver,
                                 struct usb_host_interface *alts)
{
        struct usb_ms_header_descriptor *mshd;
        struct usb_ms_endpoint_descriptor *msepd;

        /* must have the MIDIStreaming interface header descriptor*/
        mshd = (struct usb_ms_header_descriptor *)alts->extra;
        if (alts->extralen < 7 ||
            mshd->bLength < 7 ||
            mshd->bDescriptorType != USB_DT_CS_INTERFACE ||
            mshd->bDescriptorSubtype != USB_MS_HEADER)
                return -ENODEV;
        /* must have the MIDIStreaming endpoint descriptor*/
        msepd = (struct usb_ms_endpoint_descriptor *)alts->endpoint[0].extra;
        if (alts->endpoint[0].extralen < 4 ||
            msepd->bLength < 4 ||
            msepd->bDescriptorType != USB_DT_CS_ENDPOINT ||
            msepd->bDescriptorSubtype != UAC_MS_GENERAL ||
            msepd->bNumEmbMIDIJack < 1 ||
            msepd->bNumEmbMIDIJack > 16)
                return -ENODEV;

        return create_any_midi_quirk(chip, iface, driver, NULL);
}

static int create_auto_midi_quirk(struct snd_usb_audio *chip,
                                  struct usb_interface *iface,
                                  struct usb_driver *driver)
{
        struct usb_host_interface *alts;
        struct usb_interface_descriptor *altsd;
        struct usb_endpoint_descriptor *epd;
        int err;

        alts = &iface->altsetting[0];
        altsd = get_iface_desc(alts);

        /* must have at least one bulk/interrupt endpoint for streaming */
        if (altsd->bNumEndpoints < 1)
                return -ENODEV;
        epd = get_endpoint(alts, 0);
        if (!usb_endpoint_xfer_bulk(epd) &&
            !usb_endpoint_xfer_int(epd))
                return -ENODEV;

        switch (USB_ID_VENDOR(chip->usb_id)) {
        case 0x0499: /* Yamaha */
                err = create_yamaha_midi_quirk(chip, iface, driver, alts);
                if (err != -ENODEV)
                        return err;
                break;
        case 0x0582: /* Roland */
                err = create_roland_midi_quirk(chip, iface, driver, alts);
                if (err != -ENODEV)
                        return err;
                break;
        }

        return create_std_midi_quirk(chip, iface, driver, alts);
}

static int create_autodetect_quirk(struct snd_usb_audio *chip,
                                   struct usb_interface *iface,
                                   struct usb_driver *driver)
{
        int err;

        err = create_auto_pcm_quirk(chip, iface, driver);
        if (err == -ENODEV)
                err = create_auto_midi_quirk(chip, iface, driver);
        return err;
}

static int create_autodetect_quirks(struct snd_usb_audio *chip,
                                    struct usb_interface *iface,
                                    struct usb_driver *driver,
                                    const struct snd_usb_audio_quirk *quirk)
{
        int probed_ifnum = get_iface_desc(iface->altsetting)->bInterfaceNumber;
        int ifcount, ifnum, err;

        err = create_autodetect_quirk(chip, iface, driver);
        if (err < 0)
                return err;

        /*
         * ALSA PCM playback/capture devices cannot be registered in two steps,
         * so we have to claim the other corresponding interface here.
         */
        ifcount = chip->dev->actconfig->desc.bNumInterfaces;
        for (ifnum = 0; ifnum < ifcount; ifnum++) {
                if (ifnum == probed_ifnum || quirk->ifnum >= 0)
                        continue;
                iface = usb_ifnum_to_if(chip->dev, ifnum);
                if (!iface ||
                    usb_interface_claimed(iface) ||
                    get_iface_desc(iface->altsetting)->bInterfaceClass !=
                                                        USB_CLASS_VENDOR_SPEC)
                        continue;

                err = create_autodetect_quirk(chip, iface, driver);
                if (err >= 0)
                        usb_driver_claim_interface(driver, iface, (void *)-1L);
        }

        return 0;
}

/*
 * Create a stream for an Edirol UA-700/UA-25/UA-4FX interface.  
 * The only way to detect the sample rate is by looking at wMaxPacketSize.
 */
static int create_uaxx_quirk(struct snd_usb_audio *chip,
                             struct usb_interface *iface,
                             struct usb_driver *driver,
                             const struct snd_usb_audio_quirk *quirk)
{
        static const struct audioformat ua_format = {
                .formats = SNDRV_PCM_FMTBIT_S24_3LE,
                .channels = 2,
                .fmt_type = UAC_FORMAT_TYPE_I,
                .altsetting = 1,
                .altset_idx = 1,
                .rates = SNDRV_PCM_RATE_CONTINUOUS,
        };
        struct usb_host_interface *alts;
        struct usb_interface_descriptor *altsd;
        struct audioformat *fp;
        int stream, err;

        /* both PCM and MIDI interfaces have 2 or more altsettings */
        if (iface->num_altsetting < 2)
                return -ENXIO;
        alts = &iface->altsetting[1];
        altsd = get_iface_desc(alts);

        if (altsd->bNumEndpoints == 2) {
                static const struct snd_usb_midi_endpoint_info ua700_ep = {
                        .out_cables = 0x0003,
                        .in_cables  = 0x0003
                };
                static const struct snd_usb_audio_quirk ua700_quirk = {
                        .type = QUIRK_MIDI_FIXED_ENDPOINT,
                        .data = &ua700_ep
                };
                static const struct snd_usb_midi_endpoint_info uaxx_ep = {
                        .out_cables = 0x0001,
                        .in_cables  = 0x0001
                };
                static const struct snd_usb_audio_quirk uaxx_quirk = {
                        .type = QUIRK_MIDI_FIXED_ENDPOINT,
                        .data = &uaxx_ep
                };
                const struct snd_usb_audio_quirk *quirk =
                        chip->usb_id == USB_ID(0x0582, 0x002b)
                        ? &ua700_quirk : &uaxx_quirk;
                return __snd_usbmidi_create(chip->card, iface,
                                          &chip->midi_list, quirk,
                                          chip->usb_id);
        }

        if (altsd->bNumEndpoints != 1)
                return -ENXIO;

        fp = kmemdup(&ua_format, sizeof(*fp), GFP_KERNEL);
        if (!fp)
                return -ENOMEM;

        fp->iface = altsd->bInterfaceNumber;
        fp->endpoint = get_endpoint(alts, 0)->bEndpointAddress;
        fp->ep_attr = get_endpoint(alts, 0)->bmAttributes;
        fp->datainterval = 0;
        fp->maxpacksize = le16_to_cpu(get_endpoint(alts, 0)->wMaxPacketSize);
        INIT_LIST_HEAD(&fp->list);

        switch (fp->maxpacksize) {
        case 0x120:
                fp->rate_max = fp->rate_min = 44100;
                break;
        case 0x138:
        case 0x140:
                fp->rate_max = fp->rate_min = 48000;
                break;
        case 0x258:
        case 0x260:
                fp->rate_max = fp->rate_min = 96000;
                break;
        default:
                usb_audio_err(chip, "unknown sample rate\n");
                kfree(fp);
                return -ENXIO;
        }

        stream = (fp->endpoint & USB_DIR_IN)
                ? SNDRV_PCM_STREAM_CAPTURE : SNDRV_PCM_STREAM_PLAYBACK;
        err = snd_usb_add_audio_stream(chip, stream, fp);
        if (err < 0) {
                list_del(&fp->list); /* unlink for avoiding double-free */
                kfree(fp);
                return err;
        }
        usb_set_interface(chip->dev, fp->iface, 0);
        return 0;
}

/*
 * Create a standard mixer for the specified interface.
 */
static int create_standard_mixer_quirk(struct snd_usb_audio *chip,
                                       struct usb_interface *iface,
                                       struct usb_driver *driver,
                                       const struct snd_usb_audio_quirk *quirk)
{
        if (quirk->ifnum < 0)
                return 0;

        return snd_usb_create_mixer(chip, quirk->ifnum, 0);
}


static int setup_fmt_after_resume_quirk(struct snd_usb_audio *chip,
                                       struct usb_interface *iface,
                                       struct usb_driver *driver,
                                       const struct snd_usb_audio_quirk *quirk)
{
        chip->setup_fmt_after_resume_quirk = 1;
        return 1;       /* Continue with creating streams and mixer */
}

static int setup_disable_autosuspend(struct snd_usb_audio *chip,
                                       struct usb_interface *iface,
                                       struct usb_driver *driver,
                                       const struct snd_usb_audio_quirk *quirk)
{
        driver->supports_autosuspend = 0;
        return 1;       /* Continue with creating streams and mixer */
}

/*
 * audio-interface quirks
 *
 * returns zero if no standard audio/MIDI parsing is needed.
 * returns a positive value if standard audio/midi interfaces are parsed
 * after this.
 * returns a negative value at error.
 */
int snd_usb_create_quirk(struct snd_usb_audio *chip,
                         struct usb_interface *iface,
                         struct usb_driver *driver,
                         const struct snd_usb_audio_quirk *quirk)
{
        typedef int (*quirk_func_t)(struct snd_usb_audio *,
                                    struct usb_interface *,
                                    struct usb_driver *,
                                    const struct snd_usb_audio_quirk *);
        static const quirk_func_t quirk_funcs[] = {
                [QUIRK_IGNORE_INTERFACE] = ignore_interface_quirk,
                [QUIRK_COMPOSITE] = create_composite_quirk,
                [QUIRK_AUTODETECT] = create_autodetect_quirks,
                [QUIRK_MIDI_STANDARD_INTERFACE] = create_any_midi_quirk,
                [QUIRK_MIDI_FIXED_ENDPOINT] = create_any_midi_quirk,
                [QUIRK_MIDI_YAMAHA] = create_any_midi_quirk,
                [QUIRK_MIDI_ROLAND] = create_any_midi_quirk,
                [QUIRK_MIDI_MIDIMAN] = create_any_midi_quirk,
                [QUIRK_MIDI_NOVATION] = create_any_midi_quirk,
                [QUIRK_MIDI_RAW_BYTES] = create_any_midi_quirk,
                [QUIRK_MIDI_EMAGIC] = create_any_midi_quirk,
                [QUIRK_MIDI_CME] = create_any_midi_quirk,
                [QUIRK_MIDI_AKAI] = create_any_midi_quirk,
                [QUIRK_MIDI_FTDI] = create_any_midi_quirk,
                [QUIRK_MIDI_CH345] = create_any_midi_quirk,
                [QUIRK_AUDIO_STANDARD_INTERFACE] = create_standard_audio_quirk,
                [QUIRK_AUDIO_FIXED_ENDPOINT] = create_fixed_stream_quirk,
                [QUIRK_AUDIO_EDIROL_UAXX] = create_uaxx_quirk,
                [QUIRK_AUDIO_ALIGN_TRANSFER] = create_align_transfer_quirk,
                [QUIRK_AUDIO_STANDARD_MIXER] = create_standard_mixer_quirk,
                [QUIRK_SETUP_FMT_AFTER_RESUME] = setup_fmt_after_resume_quirk,
                [QUIRK_SETUP_DISABLE_AUTOSUSPEND] = setup_disable_autosuspend,
        };

        if (quirk->type < QUIRK_TYPE_COUNT) {
                return quirk_funcs[quirk->type](chip, iface, driver, quirk);
        } else {
                usb_audio_err(chip, "invalid quirk type %d\n", quirk->type);
                return -ENXIO;
        }
}

/*
 * boot quirks
 */

#define EXTIGY_FIRMWARE_SIZE_OLD 794
#define EXTIGY_FIRMWARE_SIZE_NEW 483

static int snd_usb_extigy_boot_quirk(struct usb_device *dev, struct usb_interface *intf)
{
        struct usb_host_config *config = dev->actconfig;
        int err;

        if (le16_to_cpu(get_cfg_desc(config)->wTotalLength) == EXTIGY_FIRMWARE_SIZE_OLD ||
            le16_to_cpu(get_cfg_desc(config)->wTotalLength) == EXTIGY_FIRMWARE_SIZE_NEW) {
                dev_dbg(&dev->dev, "sending Extigy boot sequence...\n");
                /* Send message to force it to reconnect with full interface. */
                err = snd_usb_ctl_msg(dev, usb_sndctrlpipe(dev,0),
                                      0x10, 0x43, 0x0001, 0x000a, NULL, 0);
                if (err < 0)
                        dev_dbg(&dev->dev, "error sending boot message: %d\n", err);
                err = usb_get_descriptor(dev, USB_DT_DEVICE, 0,
                                &dev->descriptor, sizeof(dev->descriptor));
                config = dev->actconfig;
                if (err < 0)
                        dev_dbg(&dev->dev, "error usb_get_descriptor: %d\n", err);
                err = usb_reset_configuration(dev);
                if (err < 0)
                        dev_dbg(&dev->dev, "error usb_reset_configuration: %d\n", err);
                dev_dbg(&dev->dev, "extigy_boot: new boot length = %d\n",
                            le16_to_cpu(get_cfg_desc(config)->wTotalLength));
                return -ENODEV; /* quit this anyway */
        }
        return 0;
}

static int snd_usb_audigy2nx_boot_quirk(struct usb_device *dev)
{
        u8 buf = 1;

        snd_usb_ctl_msg(dev, usb_rcvctrlpipe(dev, 0), 0x2a,
                        USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_OTHER,
                        0, 0, &buf, 1);
        if (buf == 0) {
                snd_usb_ctl_msg(dev, usb_sndctrlpipe(dev, 0), 0x29,
                                USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_OTHER,
                                1, 2000, NULL, 0);
                return -ENODEV;
        }
        return 0;
}

static int snd_usb_fasttrackpro_boot_quirk(struct usb_device *dev)
{
        int err;

        if (dev->actconfig->desc.bConfigurationValue == 1) {
                dev_info(&dev->dev,
                           "Fast Track Pro switching to config #2\n");
                /* This function has to be available by the usb core module.
                 * if it is not avialable the boot quirk has to be left out
                 * and the configuration has to be set by udev or hotplug
                 * rules
                 */
                err = usb_driver_set_configuration(dev, 2);
                if (err < 0)
                        dev_dbg(&dev->dev,
                                "error usb_driver_set_configuration: %d\n",
                                err);
                /* Always return an error, so that we stop creating a device
                   that will just be destroyed and recreated with a new
                   configuration */
                return -ENODEV;
        } else
                dev_info(&dev->dev, "Fast Track Pro config OK\n");

        return 0;
}

/*
 * C-Media CM106/CM106+ have four 16-bit internal registers that are nicely
 * documented in the device's data sheet.
 */
static int snd_usb_cm106_write_int_reg(struct usb_device *dev, int reg, u16 value)
{
        u8 buf[4];
        buf[0] = 0x20;
        buf[1] = value & 0xff;
        buf[2] = (value >> 8) & 0xff;
        buf[3] = reg;
        return snd_usb_ctl_msg(dev, usb_sndctrlpipe(dev, 0), USB_REQ_SET_CONFIGURATION,
                               USB_DIR_OUT | USB_TYPE_CLASS | USB_RECIP_ENDPOINT,
                               0, 0, &buf, 4);
}

static int snd_usb_cm106_boot_quirk(struct usb_device *dev)
{
        /*
         * Enable line-out driver mode, set headphone source to front
         * channels, enable stereo mic.
         */
        return snd_usb_cm106_write_int_reg(dev, 2, 0x8004);
}

/*
 * CM6206 registers from the CM6206 datasheet rev 2.1
 */
#define CM6206_REG0_DMA_MASTER BIT(15)
#define CM6206_REG0_SPDIFO_RATE_48K (2 << 12)
#define CM6206_REG0_SPDIFO_RATE_96K (7 << 12)
/* Bit 4 thru 11 is the S/PDIF category code */
#define CM6206_REG0_SPDIFO_CAT_CODE_GENERAL (0 << 4)
#define CM6206_REG0_SPDIFO_EMPHASIS_CD BIT(3)
#define CM6206_REG0_SPDIFO_COPYRIGHT_NA BIT(2)
#define CM6206_REG0_SPDIFO_NON_AUDIO BIT(1)
#define CM6206_REG0_SPDIFO_PRO_FORMAT BIT(0)

#define CM6206_REG1_TEST_SEL_CLK BIT(14)
#define CM6206_REG1_PLLBIN_EN BIT(13)
#define CM6206_REG1_SOFT_MUTE_EN BIT(12)
#define CM6206_REG1_GPIO4_OUT BIT(11)
#define CM6206_REG1_GPIO4_OE BIT(10)
#define CM6206_REG1_GPIO3_OUT BIT(9)
#define CM6206_REG1_GPIO3_OE BIT(8)
#define CM6206_REG1_GPIO2_OUT BIT(7)
#define CM6206_REG1_GPIO2_OE BIT(6)
#define CM6206_REG1_GPIO1_OUT BIT(5)
#define CM6206_REG1_GPIO1_OE BIT(4)
#define CM6206_REG1_SPDIFO_INVALID BIT(3)
#define CM6206_REG1_SPDIF_LOOP_EN BIT(2)
#define CM6206_REG1_SPDIFO_DIS BIT(1)
#define CM6206_REG1_SPDIFI_MIX BIT(0)

#define CM6206_REG2_DRIVER_ON BIT(15)
#define CM6206_REG2_HEADP_SEL_SIDE_CHANNELS (0 << 13)
#define CM6206_REG2_HEADP_SEL_SURROUND_CHANNELS (1 << 13)
#define CM6206_REG2_HEADP_SEL_CENTER_SUBW (2 << 13)
#define CM6206_REG2_HEADP_SEL_FRONT_CHANNELS (3 << 13)
#define CM6206_REG2_MUTE_HEADPHONE_RIGHT BIT(12)
#define CM6206_REG2_MUTE_HEADPHONE_LEFT BIT(11)
#define CM6206_REG2_MUTE_REAR_SURROUND_RIGHT BIT(10)
#define CM6206_REG2_MUTE_REAR_SURROUND_LEFT BIT(9)
#define CM6206_REG2_MUTE_SIDE_SURROUND_RIGHT BIT(8)
#define CM6206_REG2_MUTE_SIDE_SURROUND_LEFT BIT(7)
#define CM6206_REG2_MUTE_SUBWOOFER BIT(6)
#define CM6206_REG2_MUTE_CENTER BIT(5)
#define CM6206_REG2_MUTE_RIGHT_FRONT BIT(3)
#define CM6206_REG2_MUTE_LEFT_FRONT BIT(3)
#define CM6206_REG2_EN_BTL BIT(2)
#define CM6206_REG2_MCUCLKSEL_1_5_MHZ (0)
#define CM6206_REG2_MCUCLKSEL_3_MHZ (1)
#define CM6206_REG2_MCUCLKSEL_6_MHZ (2)
#define CM6206_REG2_MCUCLKSEL_12_MHZ (3)

/* Bit 11..13 sets the sensitivity to FLY tuner volume control VP/VD signal */
#define CM6206_REG3_FLYSPEED_DEFAULT (2 << 11)
#define CM6206_REG3_VRAP25EN BIT(10)
#define CM6206_REG3_MSEL1 BIT(9)
#define CM6206_REG3_SPDIFI_RATE_44_1K BIT(0 << 7)
#define CM6206_REG3_SPDIFI_RATE_48K BIT(2 << 7)
#define CM6206_REG3_SPDIFI_RATE_32K BIT(3 << 7)
#define CM6206_REG3_PINSEL BIT(6)
#define CM6206_REG3_FOE BIT(5)
#define CM6206_REG3_ROE BIT(4)
#define CM6206_REG3_CBOE BIT(3)
#define CM6206_REG3_LOSE BIT(2)
#define CM6206_REG3_HPOE BIT(1)
#define CM6206_REG3_SPDIFI_CANREC BIT(0)

#define CM6206_REG5_DA_RSTN BIT(13)
#define CM6206_REG5_AD_RSTN BIT(12)
#define CM6206_REG5_SPDIFO_AD2SPDO BIT(12)
#define CM6206_REG5_SPDIFO_SEL_FRONT (0 << 9)
#define CM6206_REG5_SPDIFO_SEL_SIDE_SUR (1 << 9)
#define CM6206_REG5_SPDIFO_SEL_CEN_LFE (2 << 9)
#define CM6206_REG5_SPDIFO_SEL_REAR_SUR (3 << 9)
#define CM6206_REG5_CODECM BIT(8)
#define CM6206_REG5_EN_HPF BIT(7)
#define CM6206_REG5_T_SEL_DSDA4 BIT(6)
#define CM6206_REG5_T_SEL_DSDA3 BIT(5)
#define CM6206_REG5_T_SEL_DSDA2 BIT(4)
#define CM6206_REG5_T_SEL_DSDA1 BIT(3)
#define CM6206_REG5_T_SEL_DSDAD_NORMAL 0
#define CM6206_REG5_T_SEL_DSDAD_FRONT 4
#define CM6206_REG5_T_SEL_DSDAD_S_SURROUND 5
#define CM6206_REG5_T_SEL_DSDAD_CEN_LFE 6
#define CM6206_REG5_T_SEL_DSDAD_R_SURROUND 7

static int snd_usb_cm6206_boot_quirk(struct usb_device *dev)
{
        int err  = 0, reg;
        int val[] = {
                /*
                 * Values here are chosen based on sniffing USB traffic
                 * under Windows.
                 *
                 * REG0: DAC is master, sample rate 48kHz, no copyright
                 */
                CM6206_REG0_SPDIFO_RATE_48K |
                CM6206_REG0_SPDIFO_COPYRIGHT_NA,
                /*
                 * REG1: PLL binary search enable, soft mute enable.
                 */
                CM6206_REG1_PLLBIN_EN |
                CM6206_REG1_SOFT_MUTE_EN,
                /*
                 * REG2: enable output drivers,
                 * select front channels to the headphone output,
                 * then mute the headphone channels, run the MCU
                 * at 1.5 MHz.
                 */
                CM6206_REG2_DRIVER_ON |
                CM6206_REG2_HEADP_SEL_FRONT_CHANNELS |
                CM6206_REG2_MUTE_HEADPHONE_RIGHT |
                CM6206_REG2_MUTE_HEADPHONE_LEFT,
                /*
                 * REG3: default flyspeed, set 2.5V mic bias
                 * enable all line out ports and enable SPDIF
                 */
                CM6206_REG3_FLYSPEED_DEFAULT |
                CM6206_REG3_VRAP25EN |
                CM6206_REG3_FOE |
                CM6206_REG3_ROE |
                CM6206_REG3_CBOE |
                CM6206_REG3_LOSE |
                CM6206_REG3_HPOE |
                CM6206_REG3_SPDIFI_CANREC,
                /* REG4 is just a bunch of GPIO lines */
                0x0000,
                /* REG5: de-assert AD/DA reset signals */
                CM6206_REG5_DA_RSTN |
                CM6206_REG5_AD_RSTN };

        for (reg = 0; reg < ARRAY_SIZE(val); reg++) {
                err = snd_usb_cm106_write_int_reg(dev, reg, val[reg]);
                if (err < 0)
                        return err;
        }

        return err;
}

/* quirk for Plantronics GameCom 780 with CM6302 chip */
static int snd_usb_gamecon780_boot_quirk(struct usb_device *dev)
{
        /* set the initial volume and don't change; other values are either
         * too loud or silent due to firmware bug (bko#65251)
         */
        u8 buf[2] = { 0x74, 0xe3 };
        return snd_usb_ctl_msg(dev, usb_sndctrlpipe(dev, 0), UAC_SET_CUR,
                        USB_RECIP_INTERFACE | USB_TYPE_CLASS | USB_DIR_OUT,
                        UAC_FU_VOLUME << 8, 9 << 8, buf, 2);
}

/*
 * Novation Twitch DJ controller
 * Focusrite Novation Saffire 6 USB audio card
 */
static int snd_usb_novation_boot_quirk(struct usb_device *dev)
{
        /* preemptively set up the device because otherwise the
         * raw MIDI endpoints are not active */
        usb_set_interface(dev, 0, 1);
        return 0;
}

/*
 * This call will put the synth in "USB send" mode, i.e it will send MIDI
 * messages through USB (this is disabled at startup). The synth will
 * acknowledge by sending a sysex on endpoint 0x85 and by displaying a USB
 * sign on its LCD. Values here are chosen based on sniffing USB traffic
 * under Windows.
 */
static int snd_usb_accessmusic_boot_quirk(struct usb_device *dev)
{
        int err, actual_length;
        /* "midi send" enable */
        static const u8 seq[] = { 0x4e, 0x73, 0x52, 0x01 };
        void *buf;

        if (usb_pipe_type_check(dev, usb_sndintpipe(dev, 0x05)))
                return -EINVAL;
        buf = kmemdup(seq, ARRAY_SIZE(seq), GFP_KERNEL);
        if (!buf)
                return -ENOMEM;
        err = usb_interrupt_msg(dev, usb_sndintpipe(dev, 0x05), buf,
                        ARRAY_SIZE(seq), &actual_length, 1000);
        kfree(buf);
        if (err < 0)
                return err;

        return 0;
}

/*
 * Some sound cards from Native Instruments are in fact compliant to the USB
 * audio standard of version 2 and other approved USB standards, even though
 * they come up as vendor-specific device when first connected.
 *
 * However, they can be told to come up with a new set of descriptors
 * upon their next enumeration, and the interfaces announced by the new
 * descriptors will then be handled by the kernel's class drivers. As the
 * product ID will also change, no further checks are required.
 */

static int snd_usb_nativeinstruments_boot_quirk(struct usb_device *dev)
{
        int ret;

        ret = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
                                  0xaf, USB_TYPE_VENDOR | USB_RECIP_DEVICE,
                                  1, 0, NULL, 0, 1000);

        if (ret < 0)
                return ret;

        usb_reset_device(dev);

        /* return -EAGAIN, so the creation of an audio interface for this
         * temporary device is aborted. The device will reconnect with a
         * new product ID */
        return -EAGAIN;
}

static void mbox2_setup_48_24_magic(struct usb_device *dev)
{
        u8 srate[3];
        u8 temp[12];

        /* Choose 48000Hz permanently */
        srate[0] = 0x80;
        srate[1] = 0xbb;
        srate[2] = 0x00;

        /* Send the magic! */
        snd_usb_ctl_msg(dev, usb_rcvctrlpipe(dev, 0),
                0x01, 0x22, 0x0100, 0x0085, &temp, 0x0003);
        snd_usb_ctl_msg(dev, usb_sndctrlpipe(dev, 0),
                0x81, 0xa2, 0x0100, 0x0085, &srate, 0x0003);
        snd_usb_ctl_msg(dev, usb_sndctrlpipe(dev, 0),
                0x81, 0xa2, 0x0100, 0x0086, &srate, 0x0003);
        snd_usb_ctl_msg(dev, usb_sndctrlpipe(dev, 0),
                0x81, 0xa2, 0x0100, 0x0003, &srate, 0x0003);
        return;
}

/* Digidesign Mbox 2 needs to load firmware onboard
 * and driver must wait a few seconds for initialisation.
 */

#define MBOX2_FIRMWARE_SIZE    646
#define MBOX2_BOOT_LOADING     0x01 /* Hard coded into the device */
#define MBOX2_BOOT_READY       0x02 /* Hard coded into the device */

static int snd_usb_mbox2_boot_quirk(struct usb_device *dev)
{
        struct usb_host_config *config = dev->actconfig;
        int err;
        u8 bootresponse[0x12];
        int fwsize;
        int count;

        fwsize = le16_to_cpu(get_cfg_desc(config)->wTotalLength);

        if (fwsize != MBOX2_FIRMWARE_SIZE) {
                dev_err(&dev->dev, "Invalid firmware size=%d.\n", fwsize);
                return -ENODEV;
        }

        dev_dbg(&dev->dev, "Sending Digidesign Mbox 2 boot sequence...\n");

        count = 0;
        bootresponse[0] = MBOX2_BOOT_LOADING;
        while ((bootresponse[0] == MBOX2_BOOT_LOADING) && (count < 10)) {
                msleep(500); /* 0.5 second delay */
                snd_usb_ctl_msg(dev, usb_rcvctrlpipe(dev, 0),
                        /* Control magic - load onboard firmware */
                        0x85, 0xc0, 0x0001, 0x0000, &bootresponse, 0x0012);
                if (bootresponse[0] == MBOX2_BOOT_READY)
                        break;
                dev_dbg(&dev->dev, "device not ready, resending boot sequence...\n");
                count++;
        }

        if (bootresponse[0] != MBOX2_BOOT_READY) {
                dev_err(&dev->dev, "Unknown bootresponse=%d, or timed out, ignoring device.\n", bootresponse[0]);
                return -ENODEV;
        }

        dev_dbg(&dev->dev, "device initialised!\n");

        err = usb_get_descriptor(dev, USB_DT_DEVICE, 0,
                &dev->descriptor, sizeof(dev->descriptor));
        config = dev->actconfig;
        if (err < 0)
                dev_dbg(&dev->dev, "error usb_get_descriptor: %d\n", err);

        err = usb_reset_configuration(dev);
        if (err < 0)
                dev_dbg(&dev->dev, "error usb_reset_configuration: %d\n", err);
        dev_dbg(&dev->dev, "mbox2_boot: new boot length = %d\n",
                le16_to_cpu(get_cfg_desc(config)->wTotalLength));

        mbox2_setup_48_24_magic(dev);

        dev_info(&dev->dev, "Digidesign Mbox 2: 24bit 48kHz");

        return 0; /* Successful boot */
}

static int snd_usb_axefx3_boot_quirk(struct usb_device *dev)
{
        int err;

        dev_dbg(&dev->dev, "Waiting for Axe-Fx III to boot up...\n");

        /* If the Axe-Fx III has not fully booted, it will timeout when trying
         * to enable the audio streaming interface. A more generous timeout is
         * used here to detect when the Axe-Fx III has finished booting as the
         * set interface message will be acked once it has
         */
        err = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),

                                USB_REQ_SET_INTERFACE, USB_RECIP_INTERFACE,
                                1, 1, NULL, 0, 120000);
        if (err < 0) {
                dev_err(&dev->dev,
                        "failed waiting for Axe-Fx III to boot: %d\n", err);
                return err;
        }

        dev_dbg(&dev->dev, "Axe-Fx III is now ready\n");

        err = usb_set_interface(dev, 1, 0);
        if (err < 0)
                dev_dbg(&dev->dev,
                        "error stopping Axe-Fx III interface: %d\n", err);

        return 0;
}


#define MICROBOOK_BUF_SIZE 128

static int snd_usb_motu_microbookii_communicate(struct usb_device *dev, u8 *buf,
                                                int buf_size, int *length)
{
        int err, actual_length;

        if (usb_pipe_type_check(dev, usb_sndintpipe(dev, 0x01)))
                return -EINVAL;
        err = usb_interrupt_msg(dev, usb_sndintpipe(dev, 0x01), buf, *length,
                                &actual_length, 1000);
        if (err < 0)
                return err;

        print_hex_dump(KERN_DEBUG, "MicroBookII snd: ", DUMP_PREFIX_NONE, 16, 1,
                       buf, actual_length, false);

        memset(buf, 0, buf_size);

        if (usb_pipe_type_check(dev, usb_rcvintpipe(dev, 0x82)))
                return -EINVAL;
        err = usb_interrupt_msg(dev, usb_rcvintpipe(dev, 0x82), buf, buf_size,
                                &actual_length, 1000);
        if (err < 0)
                return err;

        print_hex_dump(KERN_DEBUG, "MicroBookII rcv: ", DUMP_PREFIX_NONE, 16, 1,
                       buf, actual_length, false);

        *length = actual_length;
        return 0;
}

static int snd_usb_motu_microbookii_boot_quirk(struct usb_device *dev)
{
        int err, actual_length, poll_attempts = 0;
        static const u8 set_samplerate_seq[] = { 0x00, 0x00, 0x00, 0x00,
                                                 0x00, 0x00, 0x0b, 0x14,
                                                 0x00, 0x00, 0x00, 0x01 };
        static const u8 poll_ready_seq[] = { 0x00, 0x04, 0x00, 0x00,
                                             0x00, 0x00, 0x0b, 0x18 };
        u8 *buf = kzalloc(MICROBOOK_BUF_SIZE, GFP_KERNEL);

        if (!buf)
                return -ENOMEM;

        dev_info(&dev->dev, "Waiting for MOTU Microbook II to boot up...\n");

        /* First we tell the device which sample rate to use. */
        memcpy(buf, set_samplerate_seq, sizeof(set_samplerate_seq));
        actual_length = sizeof(set_samplerate_seq);
        err = snd_usb_motu_microbookii_communicate(dev, buf, MICROBOOK_BUF_SIZE,
                                                   &actual_length);

        if (err < 0) {
                dev_err(&dev->dev,
                        "failed setting the sample rate for Motu MicroBook II: %d\n",
                        err);
                goto free_buf;
        }

        /* Then we poll every 100 ms until the device informs of its readiness. */
        while (true) {
                if (++poll_attempts > 100) {
                        dev_err(&dev->dev,
                                "failed booting Motu MicroBook II: timeout\n");
                        err = -ENODEV;
                        goto free_buf;
                }

                memset(buf, 0, MICROBOOK_BUF_SIZE);
                memcpy(buf, poll_ready_seq, sizeof(poll_ready_seq));

                actual_length = sizeof(poll_ready_seq);
                err = snd_usb_motu_microbookii_communicate(
                        dev, buf, MICROBOOK_BUF_SIZE, &actual_length);
                if (err < 0) {
                        dev_err(&dev->dev,
                                "failed booting Motu MicroBook II: communication error %d\n",
                                err);
                        goto free_buf;
                }

                /* the device signals its readiness through a message of the
                 * form
                 *           XX 06 00 00 00 00 0b 18  00 00 00 01
                 * If the device is not yet ready to accept audio data, the
                 * last byte of that sequence is 00.
                 */
                if (actual_length == 12 && buf[actual_length - 1] == 1)
                        break;

                msleep(100);
        }

        dev_info(&dev->dev, "MOTU MicroBook II ready\n");

free_buf:
        kfree(buf);
        return err;
}

static int snd_usb_motu_m_series_boot_quirk(struct usb_device *dev)
{
        int ret;

        ret = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
                              1, USB_TYPE_VENDOR | USB_RECIP_DEVICE,
                              0x0, 0, NULL, 0, 1000);

        if (ret < 0)
                return ret;

        msleep(2000);

        ret = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
                              1, USB_TYPE_VENDOR | USB_RECIP_DEVICE,
                              0x20, 0, NULL, 0, 1000);

        if (ret < 0)
                return ret;

        return 0;
}

/*
 * Setup quirks
 */
#define MAUDIO_SET              0x01 /* parse device_setup */
#define MAUDIO_SET_COMPATIBLE   0x80 /* use only "win-compatible" interfaces */
#define MAUDIO_SET_DTS          0x02 /* enable DTS Digital Output */
#define MAUDIO_SET_96K          0x04 /* 48-96kHz rate if set, 8-48kHz otherwise */
#define MAUDIO_SET_24B          0x08 /* 24bits sample if set, 16bits otherwise */
#define MAUDIO_SET_DI           0x10 /* enable Digital Input */
#define MAUDIO_SET_MASK         0x1f /* bit mask for setup value */
#define MAUDIO_SET_24B_48K_DI    0x19 /* 24bits+48kHz+Digital Input */
#define MAUDIO_SET_24B_48K_NOTDI 0x09 /* 24bits+48kHz+No Digital Input */
#define MAUDIO_SET_16B_48K_DI    0x11 /* 16bits+48kHz+Digital Input */
#define MAUDIO_SET_16B_48K_NOTDI 0x01 /* 16bits+48kHz+No Digital Input */

static int quattro_skip_setting_quirk(struct snd_usb_audio *chip,
                                      int iface, int altno)
{
        /* Reset ALL ifaces to 0 altsetting.
         * Call it for every possible altsetting of every interface.
         */
        usb_set_interface(chip->dev, iface, 0);
        if (chip->setup & MAUDIO_SET) {
                if (chip->setup & MAUDIO_SET_COMPATIBLE) {
                        if (iface != 1 && iface != 2)
                                return 1; /* skip all interfaces but 1 and 2 */
                } else {
                        unsigned int mask;
                        if (iface == 1 || iface == 2)
                                return 1; /* skip interfaces 1 and 2 */
                        if ((chip->setup & MAUDIO_SET_96K) && altno != 1)
                                return 1; /* skip this altsetting */
                        mask = chip->setup & MAUDIO_SET_MASK;
                        if (mask == MAUDIO_SET_24B_48K_DI && altno != 2)
                                return 1; /* skip this altsetting */
                        if (mask == MAUDIO_SET_24B_48K_NOTDI && altno != 3)
                                return 1; /* skip this altsetting */
                        if (mask == MAUDIO_SET_16B_48K_NOTDI && altno != 4)
                                return 1; /* skip this altsetting */
                }
        }
        usb_audio_dbg(chip,
                    "using altsetting %d for interface %d config %d\n",
                    altno, iface, chip->setup);
        return 0; /* keep this altsetting */
}

static int audiophile_skip_setting_quirk(struct snd_usb_audio *chip,
                                         int iface,
                                         int altno)
{
        /* Reset ALL ifaces to 0 altsetting.
         * Call it for every possible altsetting of every interface.
         */
        usb_set_interface(chip->dev, iface, 0);

        if (chip->setup & MAUDIO_SET) {
                unsigned int mask;
                if ((chip->setup & MAUDIO_SET_DTS) && altno != 6)
                        return 1; /* skip this altsetting */
                if ((chip->setup & MAUDIO_SET_96K) && altno != 1)
                        return 1; /* skip this altsetting */
                mask = chip->setup & MAUDIO_SET_MASK;
                if (mask == MAUDIO_SET_24B_48K_DI && altno != 2)
                        return 1; /* skip this altsetting */
                if (mask == MAUDIO_SET_24B_48K_NOTDI && altno != 3)
                        return 1; /* skip this altsetting */
                if (mask == MAUDIO_SET_16B_48K_DI && altno != 4)
                        return 1; /* skip this altsetting */
                if (mask == MAUDIO_SET_16B_48K_NOTDI && altno != 5)
                        return 1; /* skip this altsetting */
        }

        return 0; /* keep this altsetting */
}

static int fasttrackpro_skip_setting_quirk(struct snd_usb_audio *chip,
                                           int iface, int altno)
{
        /* Reset ALL ifaces to 0 altsetting.
         * Call it for every possible altsetting of every interface.
         */
        usb_set_interface(chip->dev, iface, 0);

        /* possible configuration where both inputs and only one output is
         *used is not supported by the current setup
         */
        if (chip->setup & (MAUDIO_SET | MAUDIO_SET_24B)) {
                if (chip->setup & MAUDIO_SET_96K) {
                        if (altno != 3 && altno != 6)
                                return 1;
                } else if (chip->setup & MAUDIO_SET_DI) {
                        if (iface == 4)
                                return 1; /* no analog input */
                        if (altno != 2 && altno != 5)
                                return 1; /* enable only altsets 2 and 5 */
                } else {
                        if (iface == 5)
                                return 1; /* disable digialt input */
                        if (altno != 2 && altno != 5)
                                return 1; /* enalbe only altsets 2 and 5 */
                }
        } else {
                /* keep only 16-Bit mode */
                if (altno != 1)
                        return 1;
        }

        usb_audio_dbg(chip,
                    "using altsetting %d for interface %d config %d\n",
                    altno, iface, chip->setup);
        return 0; /* keep this altsetting */
}

static int s1810c_skip_setting_quirk(struct snd_usb_audio *chip,
                                           int iface, int altno)
{
        /*
         * Altno settings:
         *
         * Playback (Interface 1):
         * 1: 6 Analog + 2 S/PDIF
         * 2: 6 Analog + 2 S/PDIF
         * 3: 6 Analog
         *
         * Capture (Interface 2):
         * 1: 8 Analog + 2 S/PDIF + 8 ADAT
         * 2: 8 Analog + 2 S/PDIF + 4 ADAT
         * 3: 8 Analog
         */

        /*
         * I'll leave 2 as the default one and
         * use device_setup to switch to the
         * other two.
         */
        if ((chip->setup == 0 || chip->setup > 2) && altno != 2)
                return 1;
        else if (chip->setup == 1 && altno != 1)
                return 1;
        else if (chip->setup == 2 && altno != 3)
                return 1;

        return 0;
}

int snd_usb_apply_interface_quirk(struct snd_usb_audio *chip,
                                  int iface,
                                  int altno)
{
        /* audiophile usb: skip altsets incompatible with device_setup */
        if (chip->usb_id == USB_ID(0x0763, 0x2003))
                return audiophile_skip_setting_quirk(chip, iface, altno);
        /* quattro usb: skip altsets incompatible with device_setup */
        if (chip->usb_id == USB_ID(0x0763, 0x2001))
                return quattro_skip_setting_quirk(chip, iface, altno);
        /* fasttrackpro usb: skip altsets incompatible with device_setup */
        if (chip->usb_id == USB_ID(0x0763, 0x2012))
                return fasttrackpro_skip_setting_quirk(chip, iface, altno);
        /* presonus studio 1810c: skip altsets incompatible with device_setup */
        if (chip->usb_id == USB_ID(0x0194f, 0x010c))
                return s1810c_skip_setting_quirk(chip, iface, altno);


        return 0;
}

int snd_usb_apply_boot_quirk(struct usb_device *dev,
                             struct usb_interface *intf,
                             const struct snd_usb_audio_quirk *quirk,
                             unsigned int id)
{
        switch (id) {
        case USB_ID(0x041e, 0x3000):
                /* SB Extigy needs special boot-up sequence */
                /* if more models come, this will go to the quirk list. */
                return snd_usb_extigy_boot_quirk(dev, intf);

        case USB_ID(0x041e, 0x3020):
                /* SB Audigy 2 NX needs its own boot-up magic, too */
                return snd_usb_audigy2nx_boot_quirk(dev);

        case USB_ID(0x10f5, 0x0200):
                /* C-Media CM106 / Turtle Beach Audio Advantage Roadie */
                return snd_usb_cm106_boot_quirk(dev);

        case USB_ID(0x0d8c, 0x0102):
                /* C-Media CM6206 / CM106-Like Sound Device */
        case USB_ID(0x0ccd, 0x00b1): /* Terratec Aureon 7.1 USB */
                return snd_usb_cm6206_boot_quirk(dev);

        case USB_ID(0x0dba, 0x3000):
                /* Digidesign Mbox 2 */
                return snd_usb_mbox2_boot_quirk(dev);

        case USB_ID(0x1235, 0x0010): /* Focusrite Novation Saffire 6 USB */
        case USB_ID(0x1235, 0x0018): /* Focusrite Novation Twitch */
                return snd_usb_novation_boot_quirk(dev);

        case USB_ID(0x133e, 0x0815):
                /* Access Music VirusTI Desktop */
                return snd_usb_accessmusic_boot_quirk(dev);

        case USB_ID(0x17cc, 0x1000): /* Komplete Audio 6 */
        case USB_ID(0x17cc, 0x1010): /* Traktor Audio 6 */
        case USB_ID(0x17cc, 0x1020): /* Traktor Audio 10 */
                return snd_usb_nativeinstruments_boot_quirk(dev);
        case USB_ID(0x0763, 0x2012):  /* M-Audio Fast Track Pro USB */
                return snd_usb_fasttrackpro_boot_quirk(dev);
        case USB_ID(0x047f, 0xc010): /* Plantronics Gamecom 780 */
                return snd_usb_gamecon780_boot_quirk(dev);
        case USB_ID(0x2466, 0x8010): /* Fractal Audio Axe-Fx 3 */
                return snd_usb_axefx3_boot_quirk(dev);
        case USB_ID(0x07fd, 0x0004): /* MOTU MicroBook II */
                /*
                 * For some reason interface 3 with vendor-spec class is
                 * detected on MicroBook IIc.
                 */
                if (get_iface_desc(intf->altsetting)->bInterfaceClass ==
                    USB_CLASS_VENDOR_SPEC &&
                    get_iface_desc(intf->altsetting)->bInterfaceNumber < 3)
                        return snd_usb_motu_microbookii_boot_quirk(dev);
                break;
        }

        return 0;
}

int snd_usb_apply_boot_quirk_once(struct usb_device *dev,
                                  struct usb_interface *intf,
                                  const struct snd_usb_audio_quirk *quirk,
                                  unsigned int id)
{
        switch (id) {
        case USB_ID(0x07fd, 0x0008): /* MOTU M Series */
                return snd_usb_motu_m_series_boot_quirk(dev);
        }

        return 0;
}

/*
 * check if the device uses big-endian samples
 */
int snd_usb_is_big_endian_format(struct snd_usb_audio *chip, struct audioformat *fp)
{
        /* it depends on altsetting whether the device is big-endian or not */
        switch (chip->usb_id) {
        case USB_ID(0x0763, 0x2001): /* M-Audio Quattro: captured data only */
                if (fp->altsetting == 2 || fp->altsetting == 3 ||
                        fp->altsetting == 5 || fp->altsetting == 6)
                        return 1;
                break;
        case USB_ID(0x0763, 0x2003): /* M-Audio Audiophile USB */
                if (chip->setup == 0x00 ||
                        fp->altsetting == 1 || fp->altsetting == 2 ||
                        fp->altsetting == 3)
                        return 1;
                break;
        case USB_ID(0x0763, 0x2012): /* M-Audio Fast Track Pro */
                if (fp->altsetting == 2 || fp->altsetting == 3 ||
                        fp->altsetting == 5 || fp->altsetting == 6)
                        return 1;
                break;
        }
        return 0;
}

/*
 * For E-Mu 0404USB/0202USB/TrackerPre/0204 sample rate should be set for device,
 * not for interface.
 */

enum {
        EMU_QUIRK_SR_44100HZ = 0,
        EMU_QUIRK_SR_48000HZ,
        EMU_QUIRK_SR_88200HZ,
        EMU_QUIRK_SR_96000HZ,
        EMU_QUIRK_SR_176400HZ,
        EMU_QUIRK_SR_192000HZ
};

static void set_format_emu_quirk(struct snd_usb_substream *subs,
                                 struct audioformat *fmt)
{
        unsigned char emu_samplerate_id = 0;

        /* When capture is active
         * sample rate shouldn't be changed
         * by playback substream
         */
        if (subs->direction == SNDRV_PCM_STREAM_PLAYBACK) {
                if (subs->stream->substream[SNDRV_PCM_STREAM_CAPTURE].interface != -1)
                        return;
        }

        switch (fmt->rate_min) {
        case 48000:
                emu_samplerate_id = EMU_QUIRK_SR_48000HZ;
                break;
        case 88200:
                emu_samplerate_id = EMU_QUIRK_SR_88200HZ;
                break;
        case 96000:
                emu_samplerate_id = EMU_QUIRK_SR_96000HZ;
                break;
        case 176400:
                emu_samplerate_id = EMU_QUIRK_SR_176400HZ;
                break;
        case 192000:
                emu_samplerate_id = EMU_QUIRK_SR_192000HZ;
                break;
        default:
                emu_samplerate_id = EMU_QUIRK_SR_44100HZ;
                break;
        }
        snd_emuusb_set_samplerate(subs->stream->chip, emu_samplerate_id);
        subs->pkt_offset_adj = (emu_samplerate_id >= EMU_QUIRK_SR_176400HZ) ? 4 : 0;
}


/*
 * Pioneer DJ DJM-900NXS2
 * Device needs to know the sample rate each time substream is started
 */
static int pioneer_djm_set_format_quirk(struct snd_usb_substream *subs)
{

        /* Convert sample rate value to little endian */
        u8 sr[3];

        sr[0] = subs->cur_rate & 0xff;
        sr[1] = (subs->cur_rate >> 8) & 0xff;
        sr[2] = (subs->cur_rate >> 16) & 0xff;

        /* Configure device */
        usb_set_interface(subs->dev, 0, 1);
        snd_usb_ctl_msg(subs->stream->chip->dev,
                usb_rcvctrlpipe(subs->stream->chip->dev, 0),
                0x01, 0x22, 0x0100, 0x0082, &sr, 0x0003);

        return 0;
}

void snd_usb_set_format_quirk(struct snd_usb_substream *subs,
                              struct audioformat *fmt)
{
        switch (subs->stream->chip->usb_id) {
        case USB_ID(0x041e, 0x3f02): /* E-Mu 0202 USB */
        case USB_ID(0x041e, 0x3f04): /* E-Mu 0404 USB */
        case USB_ID(0x041e, 0x3f0a): /* E-Mu Tracker Pre */
        case USB_ID(0x041e, 0x3f19): /* E-Mu 0204 USB */
                set_format_emu_quirk(subs, fmt);
                break;
        case USB_ID(0x2b73, 0x000a): /* Pioneer DJ DJM-900NXS2 */
        case USB_ID(0x2b73, 0x0017): /* Pioneer DJ DJM-250MK2 */
                pioneer_djm_set_format_quirk(subs);
                break;
        case USB_ID(0x534d, 0x2109): /* MacroSilicon MS2109 */
                subs->stream_offset_adj = 2;
                break;
        }
}

bool snd_usb_get_sample_rate_quirk(struct snd_usb_audio *chip)
{
        /* devices which do not support reading the sample rate. */
        switch (chip->usb_id) {
        case USB_ID(0x041e, 0x4080): /* Creative Live Cam VF0610 */
        case USB_ID(0x04d8, 0xfeea): /* Benchmark DAC1 Pre */
        case USB_ID(0x0556, 0x0014): /* Phoenix Audio TMX320VC */
        case USB_ID(0x05a3, 0x9420): /* ELP HD USB Camera */
        case USB_ID(0x05a7, 0x1020): /* Bose Companion 5 */
        case USB_ID(0x074d, 0x3553): /* Outlaw RR2150 (Micronas UAC3553B) */
        case USB_ID(0x1395, 0x740a): /* Sennheiser DECT */
        case USB_ID(0x1901, 0x0191): /* GE B850V3 CP2114 audio interface */
        case USB_ID(0x21b4, 0x0081): /* AudioQuest DragonFly */
        case USB_ID(0x2912, 0x30c8): /* Audioengine D1 */
                return true;
        }

        /* devices of these vendors don't support reading rate, either */
        switch (USB_ID_VENDOR(chip->usb_id)) {
        case 0x045e: /* MS Lifecam */
        case 0x047f: /* Plantronics */
        case 0x1de7: /* Phoenix Audio */
                return true;
        }

        return false;
}

/* ITF-USB DSD based DACs need a vendor cmd to switch
 * between PCM and native DSD mode
 */
static bool is_itf_usb_dsd_dac(unsigned int id)
{
        switch (id) {
        case USB_ID(0x154e, 0x1002): /* Denon DCD-1500RE */
        case USB_ID(0x154e, 0x1003): /* Denon DA-300USB */
        case USB_ID(0x154e, 0x3005): /* Marantz HD-DAC1 */
        case USB_ID(0x154e, 0x3006): /* Marantz SA-14S1 */
        case USB_ID(0x1852, 0x5065): /* Luxman DA-06 */
        case USB_ID(0x0644, 0x8043): /* TEAC UD-501/UD-501V2/UD-503/NT-503 */
        case USB_ID(0x0644, 0x8044): /* Esoteric D-05X */
        case USB_ID(0x0644, 0x804a): /* TEAC UD-301 */
                return true;
        }
        return false;
}

int snd_usb_select_mode_quirk(struct snd_usb_substream *subs,
                              struct audioformat *fmt)
{
        struct usb_device *dev = subs->dev;
        int err;

        if (is_itf_usb_dsd_dac(subs->stream->chip->usb_id)) {
                /* First switch to alt set 0, otherwise the mode switch cmd
                 * will not be accepted by the DAC
                 */
                err = usb_set_interface(dev, fmt->iface, 0);
                if (err < 0)
                        return err;

                msleep(20); /* Delay needed after setting the interface */

                /* Vendor mode switch cmd is required. */
                if (fmt->formats & SNDRV_PCM_FMTBIT_DSD_U32_BE) {
                        /* DSD mode (DSD_U32) requested */
                        err = snd_usb_ctl_msg(dev, usb_sndctrlpipe(dev, 0), 0,
                                              USB_DIR_OUT|USB_TYPE_VENDOR|USB_RECIP_INTERFACE,
                                              1, 1, NULL, 0);
                        if (err < 0)
                                return err;

                } else {
                        /* PCM or DOP mode (S32) requested */
                        /* PCM mode (S16) requested */
                        err = snd_usb_ctl_msg(dev, usb_sndctrlpipe(dev, 0), 0,
                                              USB_DIR_OUT|USB_TYPE_VENDOR|USB_RECIP_INTERFACE,
                                              0, 1, NULL, 0);
                        if (err < 0)
                                return err;

                }
                msleep(20);
        }
        return 0;
}

void snd_usb_endpoint_start_quirk(struct snd_usb_endpoint *ep)
{
        /*
         * "Playback Design" products send bogus feedback data at the start
         * of the stream. Ignore them.
         */
        if (USB_ID_VENDOR(ep->chip->usb_id) == 0x23ba &&
            ep->type == SND_USB_ENDPOINT_TYPE_SYNC)
                ep->skip_packets = 4;

        /*
         * M-Audio Fast Track C400/C600 - when packets are not skipped, real
         * world latency varies by approx. +/- 50 frames (at 96kHz) each time
         * the stream is (re)started. When skipping packets 16 at endpoint
         * start up, the real world latency is stable within +/- 1 frame (also
         * across power cycles).
         */
        if ((ep->chip->usb_id == USB_ID(0x0763, 0x2030) ||
             ep->chip->usb_id == USB_ID(0x0763, 0x2031)) &&
            ep->type == SND_USB_ENDPOINT_TYPE_DATA)
                ep->skip_packets = 16;

        /* Work around devices that report unreasonable feedback data */
        if ((ep->chip->usb_id == USB_ID(0x0644, 0x8038) ||  /* TEAC UD-H01 */
             ep->chip->usb_id == USB_ID(0x1852, 0x5034)) && /* T+A Dac8 */
            ep->syncmaxsize == 4)
                ep->tenor_fb_quirk = 1;
}

void snd_usb_set_interface_quirk(struct usb_device *dev)
{
        struct snd_usb_audio *chip = dev_get_drvdata(&dev->dev);

        if (!chip)
                return;
        /*
         * "Playback Design" products need a 50ms delay after setting the
         * USB interface.
         */
        switch (USB_ID_VENDOR(chip->usb_id)) {
        case 0x23ba: /* Playback Design */
        case 0x0644: /* TEAC Corp. */
                msleep(50);
                break;
        }
}

/* quirk applied after snd_usb_ctl_msg(); not applied during boot quirks */
void snd_usb_ctl_msg_quirk(struct usb_device *dev, unsigned int pipe,
                           __u8 request, __u8 requesttype, __u16 value,
                           __u16 index, void *data, __u16 size)
{
        struct snd_usb_audio *chip = dev_get_drvdata(&dev->dev);

        if (!chip)
                return;
        /*
         * "Playback Design" products need a 20ms delay after each
         * class compliant request
         */
        if (USB_ID_VENDOR(chip->usb_id) == 0x23ba &&
            (requesttype & USB_TYPE_MASK) == USB_TYPE_CLASS)
                msleep(20);

        /*
         * "TEAC Corp." products need a 20ms delay after each
         * class compliant request
         */
        if (USB_ID_VENDOR(chip->usb_id) == 0x0644 &&
            (requesttype & USB_TYPE_MASK) == USB_TYPE_CLASS)
                msleep(20);

        /* ITF-USB DSD based DACs functionality need a delay
         * after each class compliant request
         */
        if (is_itf_usb_dsd_dac(chip->usb_id)
            && (requesttype & USB_TYPE_MASK) == USB_TYPE_CLASS)
                msleep(20);

        /* Zoom R16/24, many Logitech(at least H650e/H570e/BCC950),
         * Jabra 550a, Kingston HyperX needs a tiny delay here,
         * otherwise requests like get/set frequency return
         * as failed despite actually succeeding.
         */
        if ((chip->usb_id == USB_ID(0x1686, 0x00dd) ||
             USB_ID_VENDOR(chip->usb_id) == 0x046d  || /* Logitech */
             chip->usb_id == USB_ID(0x0b0e, 0x0349) ||
             chip->usb_id == USB_ID(0x0951, 0x16ad)) &&
            (requesttype & USB_TYPE_MASK) == USB_TYPE_CLASS)
                usleep_range(1000, 2000);

        /*
         * Samsung USBC Headset (AKG) need a tiny delay after each
         * class compliant request. (Model number: AAM625R or AAM627R)
         */
        if (chip->usb_id == USB_ID(0x04e8, 0xa051) &&
            (requesttype & USB_TYPE_MASK) == USB_TYPE_CLASS)
                usleep_range(5000, 6000);
}

/*
 * snd_usb_interface_dsd_format_quirks() is called from format.c to
 * augment the PCM format bit-field for DSD types. The UAC standards
 * don't have a designated bit field to denote DSD-capable interfaces,
 * hence all hardware that is known to support this format has to be
 * listed here.
 */
u64 snd_usb_interface_dsd_format_quirks(struct snd_usb_audio *chip,
                                        struct audioformat *fp,
                                        unsigned int sample_bytes)
{
        struct usb_interface *iface;

        /* Playback Designs */
        if (USB_ID_VENDOR(chip->usb_id) == 0x23ba &&
            USB_ID_PRODUCT(chip->usb_id) < 0x0110) {
                switch (fp->altsetting) {
                case 1:
                        fp->dsd_dop = true;
                        return SNDRV_PCM_FMTBIT_DSD_U16_LE;
                case 2:
                        fp->dsd_bitrev = true;
                        return SNDRV_PCM_FMTBIT_DSD_U8;
                case 3:
                        fp->dsd_bitrev = true;
                        return SNDRV_PCM_FMTBIT_DSD_U16_LE;
                }
        }

        /* XMOS based USB DACs */
        switch (chip->usb_id) {
        case USB_ID(0x1511, 0x0037): /* AURALiC VEGA */
        case USB_ID(0x2522, 0x0012): /* LH Labs VI DAC Infinity */
        case USB_ID(0x2772, 0x0230): /* Pro-Ject Pre Box S2 Digital */
                if (fp->altsetting == 2)
                        return SNDRV_PCM_FMTBIT_DSD_U32_BE;
                break;

        case USB_ID(0x0d8c, 0x0316): /* Hegel HD12 DSD */
        case USB_ID(0x10cb, 0x0103): /* The Bit Opus #3; with fp->dsd_raw */
        case USB_ID(0x16d0, 0x06b2): /* NuPrime DAC-10 */
        case USB_ID(0x16d0, 0x09dd): /* Encore mDSD */
        case USB_ID(0x16d0, 0x0733): /* Furutech ADL Stratos */
        case USB_ID(0x16d0, 0x09db): /* NuPrime Audio DAC-9 */
        case USB_ID(0x1db5, 0x0003): /* Bryston BDA3 */
        case USB_ID(0x22e1, 0xca01): /* HDTA Serenade DSD */
        case USB_ID(0x249c, 0x9326): /* M2Tech Young MkIII */
        case USB_ID(0x2616, 0x0106): /* PS Audio NuWave DAC */
        case USB_ID(0x2622, 0x0041): /* Audiolab M-DAC+ */
        case USB_ID(0x27f7, 0x3002): /* W4S DAC-2v2SE */
        case USB_ID(0x29a2, 0x0086): /* Mutec MC3+ USB */
        case USB_ID(0x6b42, 0x0042): /* MSB Technology */
                if (fp->altsetting == 3)
                        return SNDRV_PCM_FMTBIT_DSD_U32_BE;
                break;

        /* Amanero Combo384 USB based DACs with native DSD support */
        case USB_ID(0x16d0, 0x071a):  /* Amanero - Combo384 */
        case USB_ID(0x2ab6, 0x0004):  /* T+A DAC8DSD-V2.0, MP1000E-V2.0, MP2000R-V2.0, MP2500R-V2.0, MP3100HV-V2.0 */
        case USB_ID(0x2ab6, 0x0005):  /* T+A USB HD Audio 1 */
        case USB_ID(0x2ab6, 0x0006):  /* T+A USB HD Audio 2 */
                if (fp->altsetting == 2) {
                        switch (le16_to_cpu(chip->dev->descriptor.bcdDevice)) {
                        case 0x199:
                                return SNDRV_PCM_FMTBIT_DSD_U32_LE;
                        case 0x19b:
                        case 0x203:
                                return SNDRV_PCM_FMTBIT_DSD_U32_BE;
                        default:
                                break;
                        }
                }
                break;
        case USB_ID(0x16d0, 0x0a23):
                if (fp->altsetting == 2)
                        return SNDRV_PCM_FMTBIT_DSD_U32_BE;
                break;

        default:
                break;
        }

        /* ITF-USB DSD based DACs */
        if (is_itf_usb_dsd_dac(chip->usb_id)) {
                iface = usb_ifnum_to_if(chip->dev, fp->iface);

                /* Altsetting 2 support native DSD if the num of altsets is
                 * three (0-2),
                 * Altsetting 3 support native DSD if the num of altsets is
                 * four (0-3).
                 */
                if (fp->altsetting == iface->num_altsetting - 1)
                        return SNDRV_PCM_FMTBIT_DSD_U32_BE;
        }

        /* Mostly generic method to detect many DSD-capable implementations -
         * from XMOS/Thesycon
         */
        switch (USB_ID_VENDOR(chip->usb_id)) {
        case 0x152a:  /* Thesycon devices */
        case 0x20b1:  /* XMOS based devices */
        case 0x22d9:  /* Oppo */
        case 0x23ba:  /* Playback Designs */
        case 0x25ce:  /* Mytek devices */
        case 0x278b:  /* Rotel? */
        case 0x292b:  /* Gustard/Ess based devices */
        case 0x2ab6:  /* T+A devices */
        case 0x3353:  /* Khadas devices */
        case 0x3842:  /* EVGA */
        case 0xc502:  /* HiBy devices */
                if (fp->dsd_raw)
                        return SNDRV_PCM_FMTBIT_DSD_U32_BE;
                break;
        default:
                break;

        }

        return 0;
}

void snd_usb_audioformat_attributes_quirk(struct snd_usb_audio *chip,
                                          struct audioformat *fp,
                                          int stream)
{
        switch (chip->usb_id) {
        case USB_ID(0x0a92, 0x0053): /* AudioTrak Optoplay */
                /* Optoplay sets the sample rate attribute although
                 * it seems not supporting it in fact.
                 */
                fp->attributes &= ~UAC_EP_CS_ATTR_SAMPLE_RATE;
                break;
        case USB_ID(0x041e, 0x3020): /* Creative SB Audigy 2 NX */
        case USB_ID(0x0763, 0x2003): /* M-Audio Audiophile USB */
                /* doesn't set the sample rate attribute, but supports it */
                fp->attributes |= UAC_EP_CS_ATTR_SAMPLE_RATE;
                break;
        case USB_ID(0x0763, 0x2001):  /* M-Audio Quattro USB */
        case USB_ID(0x0763, 0x2012):  /* M-Audio Fast Track Pro USB */
        case USB_ID(0x047f, 0x0ca1): /* plantronics headset */
        case USB_ID(0x077d, 0x07af): /* Griffin iMic (note that there is
                                        an older model 77d:223) */
        /*
         * plantronics headset and Griffin iMic have set adaptive-in
         * although it's really not...
         */
                fp->ep_attr &= ~USB_ENDPOINT_SYNCTYPE;
                if (stream == SNDRV_PCM_STREAM_PLAYBACK)
                        fp->ep_attr |= USB_ENDPOINT_SYNC_ADAPTIVE;
                else
                        fp->ep_attr |= USB_ENDPOINT_SYNC_SYNC;
                break;
        case USB_ID(0x07fd, 0x0004):  /* MOTU MicroBook IIc */
                /*
                 * MaxPacketsOnly attribute is erroneously set in endpoint
                 * descriptors. As a result this card produces noise with
                 * all sample rates other than 96 kHz.
                 */
                fp->attributes &= ~UAC_EP_CS_ATTR_FILL_MAX;
                break;
        }
}

/*
 * registration quirk:
 * the registration is skipped if a device matches with the given ID,
 * unless the interface reaches to the defined one.  This is for delaying
 * the registration until the last known interface, so that the card and
 * devices appear at the same time.
 */

struct registration_quirk {
        unsigned int usb_id;    /* composed via USB_ID() */
        unsigned int interface; /* the interface to trigger register */
};

#define REG_QUIRK_ENTRY(vendor, product, iface) \
        { .usb_id = USB_ID(vendor, product), .interface = (iface) }

static const struct registration_quirk registration_quirks[] = {
        REG_QUIRK_ENTRY(0x0951, 0x16d8, 2),     /* Kingston HyperX AMP */
        REG_QUIRK_ENTRY(0x0951, 0x16ed, 2),     /* Kingston HyperX Cloud Alpha S */
        REG_QUIRK_ENTRY(0x0951, 0x16ea, 2),     /* Kingston HyperX Cloud Flight S */
        { 0 }                                   /* terminator */
};

/* return true if skipping registration */
bool snd_usb_registration_quirk(struct snd_usb_audio *chip, int iface)
{
        const struct registration_quirk *q;

        for (q = registration_quirks; q->usb_id; q++)
                if (chip->usb_id == q->usb_id)
                        return iface != q->interface;

        /* Register as normal */
        return false;
}