// SPDX-License-Identifier: GPL-2.0
/*
 * Intel MID PCI support
 *   Copyright (c) 2008 Intel Corporation
 *     Jesse Barnes <jesse.barnes@intel.com>
 *
 * Moorestown has an interesting PCI implementation:
 *   - configuration space is memory mapped (as defined by MCFG)
 *   - Lincroft devices also have a real, type 1 configuration space
 *   - Early Lincroft silicon has a type 1 access bug that will cause
 *     a hang if non-existent devices are accessed
 *   - some devices have the "fixed BAR" capability, which means
 *     they can't be relocated or modified; check for that during
 *     BAR sizing
 *
 * So, we use the MCFG space for all reads and writes, but also send
 * Lincroft writes to type 1 space.  But only read/write if the device
 * actually exists, otherwise return all 1s for reads and bit bucket
 * the writes.
 */

#include <linux/sched.h>
#include <linux/pci.h>
#include <linux/ioport.h>
#include <linux/init.h>
#include <linux/dmi.h>
#include <linux/acpi.h>
#include <linux/io.h>
#include <linux/smp.h>

#include <asm/segment.h>
#include <asm/pci_x86.h>
#include <asm/hw_irq.h>
#include <asm/io_apic.h>
#include <asm/intel-mid.h>
#include <asm/acpi.h>

#define PCIE_CAP_OFFSET 0x100

/* Quirks for the listed devices */
#define PCI_DEVICE_ID_INTEL_MRFLD_MMC   0x1190
#define PCI_DEVICE_ID_INTEL_MRFLD_HSU   0x1191

/* Fixed BAR fields */
#define PCIE_VNDR_CAP_ID_FIXED_BAR 0x00 /* Fixed BAR (TBD) */
#define PCI_FIXED_BAR_0_SIZE    0x04
#define PCI_FIXED_BAR_1_SIZE    0x08
#define PCI_FIXED_BAR_2_SIZE    0x0c
#define PCI_FIXED_BAR_3_SIZE    0x10
#define PCI_FIXED_BAR_4_SIZE    0x14
#define PCI_FIXED_BAR_5_SIZE    0x1c

static int pci_soc_mode;

/**
 * fixed_bar_cap - return the offset of the fixed BAR cap if found
 * @bus: PCI bus
 * @devfn: device in question
 *
 * Look for the fixed BAR cap on @bus and @devfn, returning its offset
 * if found or 0 otherwise.
 */
static int fixed_bar_cap(struct pci_bus *bus, unsigned int devfn)
{
        int pos;
        u32 pcie_cap = 0, cap_data;

        pos = PCIE_CAP_OFFSET;

        if (!raw_pci_ext_ops)
                return 0;

        while (pos) {
                if (raw_pci_ext_ops->read(pci_domain_nr(bus), bus->number,
                                          devfn, pos, 4, &pcie_cap))
                        return 0;

                if (PCI_EXT_CAP_ID(pcie_cap) == 0x0000 ||
                        PCI_EXT_CAP_ID(pcie_cap) == 0xffff)
                        break;

                if (PCI_EXT_CAP_ID(pcie_cap) == PCI_EXT_CAP_ID_VNDR) {
                        raw_pci_ext_ops->read(pci_domain_nr(bus), bus->number,
                                              devfn, pos + 4, 4, &cap_data);
                        if ((cap_data & 0xffff) == PCIE_VNDR_CAP_ID_FIXED_BAR)
                                return pos;
                }

                pos = PCI_EXT_CAP_NEXT(pcie_cap);
        }

        return 0;
}

static int pci_device_update_fixed(struct pci_bus *bus, unsigned int devfn,
                                   int reg, int len, u32 val, int offset)
{
        u32 size;
        unsigned int domain, busnum;
        int bar = (reg - PCI_BASE_ADDRESS_0) >> 2;

        domain = pci_domain_nr(bus);
        busnum = bus->number;

        if (val == ~0 && len == 4) {
                unsigned long decode;

                raw_pci_ext_ops->read(domain, busnum, devfn,
                               offset + 8 + (bar * 4), 4, &size);

                /* Turn the size into a decode pattern for the sizing code */
                if (size) {
                        decode = size - 1;
                        decode |= decode >> 1;
                        decode |= decode >> 2;
                        decode |= decode >> 4;
                        decode |= decode >> 8;
                        decode |= decode >> 16;
                        decode++;
                        decode = ~(decode - 1);
                } else {
                        decode = 0;
                }

                /*
                 * If val is all ones, the core code is trying to size the reg,
                 * so update the mmconfig space with the real size.
                 *
                 * Note: this assumes the fixed size we got is a power of two.
                 */
                return raw_pci_ext_ops->write(domain, busnum, devfn, reg, 4,
                                       decode);
        }

        /* This is some other kind of BAR write, so just do it. */
        return raw_pci_ext_ops->write(domain, busnum, devfn, reg, len, val);
}

/**
 * type1_access_ok - check whether to use type 1
 * @bus: bus number
 * @devfn: device & function in question
 *
 * If the bus is on a Lincroft chip and it exists, or is not on a Lincroft at
 * all, the we can go ahead with any reads & writes.  If it's on a Lincroft,
 * but doesn't exist, avoid the access altogether to keep the chip from
 * hanging.
 */
static bool type1_access_ok(unsigned int bus, unsigned int devfn, int reg)
{
        /*
         * This is a workaround for A0 LNC bug where PCI status register does
         * not have new CAP bit set. can not be written by SW either.
         *
         * PCI header type in real LNC indicates a single function device, this
         * will prevent probing other devices under the same function in PCI
         * shim. Therefore, use the header type in shim instead.
         */
        if (reg >= 0x100 || reg == PCI_STATUS || reg == PCI_HEADER_TYPE)
                return false;
        if (bus == 0 && (devfn == PCI_DEVFN(2, 0)
                                || devfn == PCI_DEVFN(0, 0)
                                || devfn == PCI_DEVFN(3, 0)))
                return true;
        return false; /* Langwell on others */
}

static int pci_read(struct pci_bus *bus, unsigned int devfn, int where,
                    int size, u32 *value)
{
        if (type1_access_ok(bus->number, devfn, where))
                return pci_direct_conf1.read(pci_domain_nr(bus), bus->number,
                                        devfn, where, size, value);
        return raw_pci_ext_ops->read(pci_domain_nr(bus), bus->number,
                              devfn, where, size, value);
}

static int pci_write(struct pci_bus *bus, unsigned int devfn, int where,
                     int size, u32 value)
{
        int offset;

        /*
         * On MRST, there is no PCI ROM BAR, this will cause a subsequent read
         * to ROM BAR return 0 then being ignored.
         */
        if (where == PCI_ROM_ADDRESS)
                return 0;

        /*
         * Devices with fixed BARs need special handling:
         *   - BAR sizing code will save, write ~0, read size, restore
         *   - so writes to fixed BARs need special handling
         *   - other writes to fixed BAR devices should go through mmconfig
         */
        offset = fixed_bar_cap(bus, devfn);
        if (offset &&
            (where >= PCI_BASE_ADDRESS_0 && where <= PCI_BASE_ADDRESS_5)) {
                return pci_device_update_fixed(bus, devfn, where, size, value,
                                               offset);
        }

        /*
         * On Moorestown update both real & mmconfig space
         * Note: early Lincroft silicon can't handle type 1 accesses to
         *       non-existent devices, so just eat the write in that case.
         */
        if (type1_access_ok(bus->number, devfn, where))
                return pci_direct_conf1.write(pci_domain_nr(bus), bus->number,
                                              devfn, where, size, value);
        return raw_pci_ext_ops->write(pci_domain_nr(bus), bus->number, devfn,
                               where, size, value);
}

static int intel_mid_pci_irq_enable(struct pci_dev *dev)
{
        struct irq_alloc_info info;
        int polarity;
        int ret;
        u8 gsi;

        if (dev->irq_managed && dev->irq > 0)
                return 0;

        ret = pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &gsi);
        if (ret < 0) {
                dev_warn(&dev->dev, "Failed to read interrupt line: %d\n", ret);
                return ret;
        }

        switch (intel_mid_identify_cpu()) {
        case INTEL_MID_CPU_CHIP_TANGIER:
                polarity = IOAPIC_POL_HIGH;

                /* Special treatment for IRQ0 */
                if (gsi == 0) {
                        /*
                         * Skip HS UART common registers device since it has
                         * IRQ0 assigned and not used by the kernel.
                         */
                        if (dev->device == PCI_DEVICE_ID_INTEL_MRFLD_HSU)
                                return -EBUSY;
                        /*
                         * TNG has IRQ0 assigned to eMMC controller. But there
                         * are also other devices with bogus PCI configuration
                         * that have IRQ0 assigned. This check ensures that
                         * eMMC gets it. The rest of devices still could be
                         * enabled without interrupt line being allocated.
                         */
                        if (dev->device != PCI_DEVICE_ID_INTEL_MRFLD_MMC)
                                return 0;
                }
                break;
        default:
                polarity = IOAPIC_POL_LOW;
                break;
        }

        ioapic_set_alloc_attr(&info, dev_to_node(&dev->dev), 1, polarity);

        /*
         * MRST only have IOAPIC, the PCI irq lines are 1:1 mapped to
         * IOAPIC RTE entries, so we just enable RTE for the device.
         */
        ret = mp_map_gsi_to_irq(gsi, IOAPIC_MAP_ALLOC, &info);
        if (ret < 0)
                return ret;

        dev->irq = ret;
        dev->irq_managed = 1;

        return 0;
}

static void intel_mid_pci_irq_disable(struct pci_dev *dev)
{
        if (!mp_should_keep_irq(&dev->dev) && dev->irq_managed &&
            dev->irq > 0) {
                mp_unmap_irq(dev->irq);
                dev->irq_managed = 0;
        }
}

static const struct pci_ops intel_mid_pci_ops __initconst = {
        .read = pci_read,
        .write = pci_write,
};

/**
 * intel_mid_pci_init - installs intel_mid_pci_ops
 *
 * Moorestown has an interesting PCI implementation (see above).
 * Called when the early platform detection installs it.
 */
int __init intel_mid_pci_init(void)
{
        pr_info("Intel MID platform detected, using MID PCI ops\n");
        pci_mmcfg_late_init();
        pcibios_enable_irq = intel_mid_pci_irq_enable;
        pcibios_disable_irq = intel_mid_pci_irq_disable;
        pci_root_ops = intel_mid_pci_ops;
        pci_soc_mode = 1;
        /* Continue with standard init */
        acpi_noirq_set();
        return 1;
}

/*
 * Langwell devices are not true PCI devices; they are not subject to 10 ms
 * d3 to d0 delay required by PCI spec.
 */
static void pci_d3delay_fixup(struct pci_dev *dev)
{
        /*
         * PCI fixups are effectively decided compile time. If we have a dual
         * SoC/non-SoC kernel we don't want to mangle d3 on non-SoC devices.
         */
        if (!pci_soc_mode)
                return;
        /*
         * True PCI devices in Lincroft should allow type 1 access, the rest
         * are Langwell fake PCI devices.
         */
        if (type1_access_ok(dev->bus->number, dev->devfn, PCI_DEVICE_ID))
                return;
        dev->d3hot_delay = 0;
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, pci_d3delay_fixup);

static void mid_power_off_one_device(struct pci_dev *dev)
{
        u16 pmcsr;

        /*
         * Update current state first, otherwise PCI core enforces PCI_D0 in
         * pci_set_power_state() for devices which status was PCI_UNKNOWN.
         */
        pci_read_config_word(dev, dev->pm_cap + PCI_PM_CTRL, &pmcsr);
        dev->current_state = (pci_power_t __force)(pmcsr & PCI_PM_CTRL_STATE_MASK);

        pci_set_power_state(dev, PCI_D3hot);
}

static void mid_power_off_devices(struct pci_dev *dev)
{
        int id;

        if (!pci_soc_mode)
                return;

        id = intel_mid_pwr_get_lss_id(dev);
        if (id < 0)
                return;

        /*
         * This sets only PMCSR bits. The actual power off will happen in
         * arch/x86/platform/intel-mid/pwr.c.
         */
        mid_power_off_one_device(dev);
}

DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, mid_power_off_devices);

/*
 * Langwell devices reside at fixed offsets, don't try to move them.
 */
static void pci_fixed_bar_fixup(struct pci_dev *dev)
{
        unsigned long offset;
        u32 size;
        int i;

        if (!pci_soc_mode)
                return;

        /* Must have extended configuration space */
        if (dev->cfg_size < PCIE_CAP_OFFSET + 4)
                return;

        /* Fixup the BAR sizes for fixed BAR devices and make them unmoveable */
        offset = fixed_bar_cap(dev->bus, dev->devfn);
        if (!offset || PCI_DEVFN(2, 0) == dev->devfn ||
            PCI_DEVFN(2, 2) == dev->devfn)
                return;

        for (i = 0; i < PCI_STD_NUM_BARS; i++) {
                pci_read_config_dword(dev, offset + 8 + (i * 4), &size);
                dev->resource[i].end = dev->resource[i].start + size - 1;
                dev->resource[i].flags |= IORESOURCE_PCI_FIXED;
        }
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, pci_fixed_bar_fixup);