linux/drivers/media/tuners/mt2060.c
<<
>>
Prefs
   1// SPDX-License-Identifier: GPL-2.0-or-later
   2/*
   3 *  Driver for Microtune MT2060 "Single chip dual conversion broadband tuner"
   4 *
   5 *  Copyright (c) 2006 Olivier DANET <odanet@caramail.com>
   6 */
   7
   8/* In that file, frequencies are expressed in kiloHertz to avoid 32 bits overflows */
   9
  10#include <linux/module.h>
  11#include <linux/delay.h>
  12#include <linux/dvb/frontend.h>
  13#include <linux/i2c.h>
  14#include <linux/slab.h>
  15
  16#include <media/dvb_frontend.h>
  17
  18#include "mt2060.h"
  19#include "mt2060_priv.h"
  20
  21static int debug;
  22module_param(debug, int, 0644);
  23MODULE_PARM_DESC(debug, "Turn on/off debugging (default:off).");
  24
  25#define dprintk(args...) do { if (debug) {printk(KERN_DEBUG "MT2060: " args); printk("\n"); }} while (0)
  26
  27// Reads a single register
  28static int mt2060_readreg(struct mt2060_priv *priv, u8 reg, u8 *val)
  29{
  30        struct i2c_msg msg[2] = {
  31                { .addr = priv->cfg->i2c_address, .flags = 0, .len = 1 },
  32                { .addr = priv->cfg->i2c_address, .flags = I2C_M_RD, .len = 1 },
  33        };
  34        int rc = 0;
  35        u8 *b;
  36
  37        b = kmalloc(2, GFP_KERNEL);
  38        if (!b)
  39                return -ENOMEM;
  40
  41        b[0] = reg;
  42        b[1] = 0;
  43
  44        msg[0].buf = b;
  45        msg[1].buf = b + 1;
  46
  47        if (i2c_transfer(priv->i2c, msg, 2) != 2) {
  48                printk(KERN_WARNING "mt2060 I2C read failed\n");
  49                rc = -EREMOTEIO;
  50        }
  51        *val = b[1];
  52        kfree(b);
  53
  54        return rc;
  55}
  56
  57// Writes a single register
  58static int mt2060_writereg(struct mt2060_priv *priv, u8 reg, u8 val)
  59{
  60        struct i2c_msg msg = {
  61                .addr = priv->cfg->i2c_address, .flags = 0, .len = 2
  62        };
  63        u8 *buf;
  64        int rc = 0;
  65
  66        buf = kmalloc(2, GFP_KERNEL);
  67        if (!buf)
  68                return -ENOMEM;
  69
  70        buf[0] = reg;
  71        buf[1] = val;
  72
  73        msg.buf = buf;
  74
  75        if (i2c_transfer(priv->i2c, &msg, 1) != 1) {
  76                printk(KERN_WARNING "mt2060 I2C write failed\n");
  77                rc = -EREMOTEIO;
  78        }
  79        kfree(buf);
  80        return rc;
  81}
  82
  83// Writes a set of consecutive registers
  84static int mt2060_writeregs(struct mt2060_priv *priv,u8 *buf, u8 len)
  85{
  86        int rem, val_len;
  87        u8 *xfer_buf;
  88        int rc = 0;
  89        struct i2c_msg msg = {
  90                .addr = priv->cfg->i2c_address, .flags = 0
  91        };
  92
  93        xfer_buf = kmalloc(16, GFP_KERNEL);
  94        if (!xfer_buf)
  95                return -ENOMEM;
  96
  97        msg.buf = xfer_buf;
  98
  99        for (rem = len - 1; rem > 0; rem -= priv->i2c_max_regs) {
 100                val_len = min_t(int, rem, priv->i2c_max_regs);
 101                msg.len = 1 + val_len;
 102                xfer_buf[0] = buf[0] + len - 1 - rem;
 103                memcpy(&xfer_buf[1], &buf[1 + len - 1 - rem], val_len);
 104
 105                if (i2c_transfer(priv->i2c, &msg, 1) != 1) {
 106                        printk(KERN_WARNING "mt2060 I2C write failed (len=%i)\n", val_len);
 107                        rc = -EREMOTEIO;
 108                        break;
 109                }
 110        }
 111
 112        kfree(xfer_buf);
 113        return rc;
 114}
 115
 116// Initialisation sequences
 117// LNABAND=3, NUM1=0x3C, DIV1=0x74, NUM2=0x1080, DIV2=0x49
 118static u8 mt2060_config1[] = {
 119        REG_LO1C1,
 120        0x3F,   0x74,   0x00,   0x08,   0x93
 121};
 122
 123// FMCG=2, GP2=0, GP1=0
 124static u8 mt2060_config2[] = {
 125        REG_MISC_CTRL,
 126        0x20,   0x1E,   0x30,   0xff,   0x80,   0xff,   0x00,   0x2c,   0x42
 127};
 128
 129//  VGAG=3, V1CSE=1
 130
 131#ifdef  MT2060_SPURCHECK
 132/* The function below calculates the frequency offset between the output frequency if2
 133 and the closer cross modulation subcarrier between lo1 and lo2 up to the tenth harmonic */
 134static int mt2060_spurcalc(u32 lo1,u32 lo2,u32 if2)
 135{
 136        int I,J;
 137        int dia,diamin,diff;
 138        diamin=1000000;
 139        for (I = 1; I < 10; I++) {
 140                J = ((2*I*lo1)/lo2+1)/2;
 141                diff = I*(int)lo1-J*(int)lo2;
 142                if (diff < 0) diff=-diff;
 143                dia = (diff-(int)if2);
 144                if (dia < 0) dia=-dia;
 145                if (diamin > dia) diamin=dia;
 146        }
 147        return diamin;
 148}
 149
 150#define BANDWIDTH 4000 // kHz
 151
 152/* Calculates the frequency offset to add to avoid spurs. Returns 0 if no offset is needed */
 153static int mt2060_spurcheck(u32 lo1,u32 lo2,u32 if2)
 154{
 155        u32 Spur,Sp1,Sp2;
 156        int I,J;
 157        I=0;
 158        J=1000;
 159
 160        Spur=mt2060_spurcalc(lo1,lo2,if2);
 161        if (Spur < BANDWIDTH) {
 162                /* Potential spurs detected */
 163                dprintk("Spurs before : f_lo1: %d  f_lo2: %d  (kHz)",
 164                        (int)lo1,(int)lo2);
 165                I=1000;
 166                Sp1 = mt2060_spurcalc(lo1+I,lo2+I,if2);
 167                Sp2 = mt2060_spurcalc(lo1-I,lo2-I,if2);
 168
 169                if (Sp1 < Sp2) {
 170                        J=-J; I=-I; Spur=Sp2;
 171                } else
 172                        Spur=Sp1;
 173
 174                while (Spur < BANDWIDTH) {
 175                        I += J;
 176                        Spur = mt2060_spurcalc(lo1+I,lo2+I,if2);
 177                }
 178                dprintk("Spurs after  : f_lo1: %d  f_lo2: %d  (kHz)",
 179                        (int)(lo1+I),(int)(lo2+I));
 180        }
 181        return I;
 182}
 183#endif
 184
 185#define IF2  36150       // IF2 frequency = 36.150 MHz
 186#define FREF 16000       // Quartz oscillator 16 MHz
 187
 188static int mt2060_set_params(struct dvb_frontend *fe)
 189{
 190        struct dtv_frontend_properties *c = &fe->dtv_property_cache;
 191        struct mt2060_priv *priv;
 192        int i=0;
 193        u32 freq;
 194        u8  lnaband;
 195        u32 f_lo1,f_lo2;
 196        u32 div1,num1,div2,num2;
 197        u8  b[8];
 198        u32 if1;
 199
 200        priv = fe->tuner_priv;
 201
 202        if1 = priv->if1_freq;
 203        b[0] = REG_LO1B1;
 204        b[1] = 0xFF;
 205
 206        if (fe->ops.i2c_gate_ctrl)
 207                fe->ops.i2c_gate_ctrl(fe, 1); /* open i2c_gate */
 208
 209        mt2060_writeregs(priv,b,2);
 210
 211        freq = c->frequency / 1000; /* Hz -> kHz */
 212
 213        f_lo1 = freq + if1 * 1000;
 214        f_lo1 = (f_lo1 / 250) * 250;
 215        f_lo2 = f_lo1 - freq - IF2;
 216        // From the Comtech datasheet, the step used is 50kHz. The tuner chip could be more precise
 217        f_lo2 = ((f_lo2 + 25) / 50) * 50;
 218        priv->frequency =  (f_lo1 - f_lo2 - IF2) * 1000,
 219
 220#ifdef MT2060_SPURCHECK
 221        // LO-related spurs detection and correction
 222        num1   = mt2060_spurcheck(f_lo1,f_lo2,IF2);
 223        f_lo1 += num1;
 224        f_lo2 += num1;
 225#endif
 226        //Frequency LO1 = 16MHz * (DIV1 + NUM1/64 )
 227        num1 = f_lo1 / (FREF / 64);
 228        div1 = num1 / 64;
 229        num1 &= 0x3f;
 230
 231        // Frequency LO2 = 16MHz * (DIV2 + NUM2/8192 )
 232        num2 = f_lo2 * 64 / (FREF / 128);
 233        div2 = num2 / 8192;
 234        num2 &= 0x1fff;
 235
 236        if (freq <=  95000) lnaband = 0xB0; else
 237        if (freq <= 180000) lnaband = 0xA0; else
 238        if (freq <= 260000) lnaband = 0x90; else
 239        if (freq <= 335000) lnaband = 0x80; else
 240        if (freq <= 425000) lnaband = 0x70; else
 241        if (freq <= 480000) lnaband = 0x60; else
 242        if (freq <= 570000) lnaband = 0x50; else
 243        if (freq <= 645000) lnaband = 0x40; else
 244        if (freq <= 730000) lnaband = 0x30; else
 245        if (freq <= 810000) lnaband = 0x20; else lnaband = 0x10;
 246
 247        b[0] = REG_LO1C1;
 248        b[1] = lnaband | ((num1 >>2) & 0x0F);
 249        b[2] = div1;
 250        b[3] = (num2 & 0x0F)  | ((num1 & 3) << 4);
 251        b[4] = num2 >> 4;
 252        b[5] = ((num2 >>12) & 1) | (div2 << 1);
 253
 254        dprintk("IF1: %dMHz",(int)if1);
 255        dprintk("PLL freq=%dkHz  f_lo1=%dkHz  f_lo2=%dkHz",(int)freq,(int)f_lo1,(int)f_lo2);
 256        dprintk("PLL div1=%d  num1=%d  div2=%d  num2=%d",(int)div1,(int)num1,(int)div2,(int)num2);
 257        dprintk("PLL [1..5]: %2x %2x %2x %2x %2x",(int)b[1],(int)b[2],(int)b[3],(int)b[4],(int)b[5]);
 258
 259        mt2060_writeregs(priv,b,6);
 260
 261        //Waits for pll lock or timeout
 262        i = 0;
 263        do {
 264                mt2060_readreg(priv,REG_LO_STATUS,b);
 265                if ((b[0] & 0x88)==0x88)
 266                        break;
 267                msleep(4);
 268                i++;
 269        } while (i<10);
 270
 271        if (fe->ops.i2c_gate_ctrl)
 272                fe->ops.i2c_gate_ctrl(fe, 0); /* close i2c_gate */
 273
 274        return 0;
 275}
 276
 277static void mt2060_calibrate(struct mt2060_priv *priv)
 278{
 279        u8 b = 0;
 280        int i = 0;
 281
 282        if (mt2060_writeregs(priv,mt2060_config1,sizeof(mt2060_config1)))
 283                return;
 284        if (mt2060_writeregs(priv,mt2060_config2,sizeof(mt2060_config2)))
 285                return;
 286
 287        /* initialize the clock output */
 288        mt2060_writereg(priv, REG_VGAG, (priv->cfg->clock_out << 6) | 0x30);
 289
 290        do {
 291                b |= (1 << 6); // FM1SS;
 292                mt2060_writereg(priv, REG_LO2C1,b);
 293                msleep(20);
 294
 295                if (i == 0) {
 296                        b |= (1 << 7); // FM1CA;
 297                        mt2060_writereg(priv, REG_LO2C1,b);
 298                        b &= ~(1 << 7); // FM1CA;
 299                        msleep(20);
 300                }
 301
 302                b &= ~(1 << 6); // FM1SS
 303                mt2060_writereg(priv, REG_LO2C1,b);
 304
 305                msleep(20);
 306                i++;
 307        } while (i < 9);
 308
 309        i = 0;
 310        while (i++ < 10 && mt2060_readreg(priv, REG_MISC_STAT, &b) == 0 && (b & (1 << 6)) == 0)
 311                msleep(20);
 312
 313        if (i <= 10) {
 314                mt2060_readreg(priv, REG_FM_FREQ, &priv->fmfreq); // now find out, what is fmreq used for :)
 315                dprintk("calibration was successful: %d", (int)priv->fmfreq);
 316        } else
 317                dprintk("FMCAL timed out");
 318}
 319
 320static int mt2060_get_frequency(struct dvb_frontend *fe, u32 *frequency)
 321{
 322        struct mt2060_priv *priv = fe->tuner_priv;
 323        *frequency = priv->frequency;
 324        return 0;
 325}
 326
 327static int mt2060_get_if_frequency(struct dvb_frontend *fe, u32 *frequency)
 328{
 329        *frequency = IF2 * 1000;
 330        return 0;
 331}
 332
 333static int mt2060_init(struct dvb_frontend *fe)
 334{
 335        struct mt2060_priv *priv = fe->tuner_priv;
 336        int ret;
 337
 338        if (fe->ops.i2c_gate_ctrl)
 339                fe->ops.i2c_gate_ctrl(fe, 1); /* open i2c_gate */
 340
 341        if (priv->sleep) {
 342                ret = mt2060_writereg(priv, REG_MISC_CTRL, 0x20);
 343                if (ret)
 344                        goto err_i2c_gate_ctrl;
 345        }
 346
 347        ret = mt2060_writereg(priv, REG_VGAG,
 348                              (priv->cfg->clock_out << 6) | 0x33);
 349
 350err_i2c_gate_ctrl:
 351        if (fe->ops.i2c_gate_ctrl)
 352                fe->ops.i2c_gate_ctrl(fe, 0); /* close i2c_gate */
 353
 354        return ret;
 355}
 356
 357static int mt2060_sleep(struct dvb_frontend *fe)
 358{
 359        struct mt2060_priv *priv = fe->tuner_priv;
 360        int ret;
 361
 362        if (fe->ops.i2c_gate_ctrl)
 363                fe->ops.i2c_gate_ctrl(fe, 1); /* open i2c_gate */
 364
 365        ret = mt2060_writereg(priv, REG_VGAG,
 366                              (priv->cfg->clock_out << 6) | 0x30);
 367        if (ret)
 368                goto err_i2c_gate_ctrl;
 369
 370        if (priv->sleep)
 371                ret = mt2060_writereg(priv, REG_MISC_CTRL, 0xe8);
 372
 373err_i2c_gate_ctrl:
 374        if (fe->ops.i2c_gate_ctrl)
 375                fe->ops.i2c_gate_ctrl(fe, 0); /* close i2c_gate */
 376
 377        return ret;
 378}
 379
 380static void mt2060_release(struct dvb_frontend *fe)
 381{
 382        kfree(fe->tuner_priv);
 383        fe->tuner_priv = NULL;
 384}
 385
 386static const struct dvb_tuner_ops mt2060_tuner_ops = {
 387        .info = {
 388                .name              = "Microtune MT2060",
 389                .frequency_min_hz  =  48 * MHz,
 390                .frequency_max_hz  = 860 * MHz,
 391                .frequency_step_hz =  50 * kHz,
 392        },
 393
 394        .release       = mt2060_release,
 395
 396        .init          = mt2060_init,
 397        .sleep         = mt2060_sleep,
 398
 399        .set_params    = mt2060_set_params,
 400        .get_frequency = mt2060_get_frequency,
 401        .get_if_frequency = mt2060_get_if_frequency,
 402};
 403
 404/* This functions tries to identify a MT2060 tuner by reading the PART/REV register. This is hasty. */
 405struct dvb_frontend * mt2060_attach(struct dvb_frontend *fe, struct i2c_adapter *i2c, struct mt2060_config *cfg, u16 if1)
 406{
 407        struct mt2060_priv *priv = NULL;
 408        u8 id = 0;
 409
 410        priv = kzalloc(sizeof(struct mt2060_priv), GFP_KERNEL);
 411        if (priv == NULL)
 412                return NULL;
 413
 414        priv->cfg      = cfg;
 415        priv->i2c      = i2c;
 416        priv->if1_freq = if1;
 417        priv->i2c_max_regs = ~0;
 418
 419        if (fe->ops.i2c_gate_ctrl)
 420                fe->ops.i2c_gate_ctrl(fe, 1); /* open i2c_gate */
 421
 422        if (mt2060_readreg(priv,REG_PART_REV,&id) != 0) {
 423                kfree(priv);
 424                return NULL;
 425        }
 426
 427        if (id != PART_REV) {
 428                kfree(priv);
 429                return NULL;
 430        }
 431        printk(KERN_INFO "MT2060: successfully identified (IF1 = %d)\n", if1);
 432        memcpy(&fe->ops.tuner_ops, &mt2060_tuner_ops, sizeof(struct dvb_tuner_ops));
 433
 434        fe->tuner_priv = priv;
 435
 436        mt2060_calibrate(priv);
 437
 438        if (fe->ops.i2c_gate_ctrl)
 439                fe->ops.i2c_gate_ctrl(fe, 0); /* close i2c_gate */
 440
 441        return fe;
 442}
 443EXPORT_SYMBOL(mt2060_attach);
 444
 445static int mt2060_probe(struct i2c_client *client,
 446                        const struct i2c_device_id *id)
 447{
 448        struct mt2060_platform_data *pdata = client->dev.platform_data;
 449        struct dvb_frontend *fe;
 450        struct mt2060_priv *dev;
 451        int ret;
 452        u8 chip_id;
 453
 454        dev_dbg(&client->dev, "\n");
 455
 456        if (!pdata) {
 457                dev_err(&client->dev, "Cannot proceed without platform data\n");
 458                ret = -EINVAL;
 459                goto err;
 460        }
 461
 462        dev = devm_kzalloc(&client->dev, sizeof(*dev), GFP_KERNEL);
 463        if (!dev) {
 464                ret = -ENOMEM;
 465                goto err;
 466        }
 467
 468        fe = pdata->dvb_frontend;
 469        dev->config.i2c_address = client->addr;
 470        dev->config.clock_out = pdata->clock_out;
 471        dev->cfg = &dev->config;
 472        dev->i2c = client->adapter;
 473        dev->if1_freq = pdata->if1 ? pdata->if1 : 1220;
 474        dev->client = client;
 475        dev->i2c_max_regs = pdata->i2c_write_max ? pdata->i2c_write_max - 1 : ~0;
 476        dev->sleep = true;
 477
 478        ret = mt2060_readreg(dev, REG_PART_REV, &chip_id);
 479        if (ret) {
 480                ret = -ENODEV;
 481                goto err;
 482        }
 483
 484        dev_dbg(&client->dev, "chip id=%02x\n", chip_id);
 485
 486        if (chip_id != PART_REV) {
 487                ret = -ENODEV;
 488                goto err;
 489        }
 490
 491        /* Power on, calibrate, sleep */
 492        ret = mt2060_writereg(dev, REG_MISC_CTRL, 0x20);
 493        if (ret)
 494                goto err;
 495        mt2060_calibrate(dev);
 496        ret = mt2060_writereg(dev, REG_MISC_CTRL, 0xe8);
 497        if (ret)
 498                goto err;
 499
 500        dev_info(&client->dev, "Microtune MT2060 successfully identified\n");
 501        memcpy(&fe->ops.tuner_ops, &mt2060_tuner_ops, sizeof(fe->ops.tuner_ops));
 502        fe->ops.tuner_ops.release = NULL;
 503        fe->tuner_priv = dev;
 504        i2c_set_clientdata(client, dev);
 505
 506        return 0;
 507err:
 508        dev_dbg(&client->dev, "failed=%d\n", ret);
 509        return ret;
 510}
 511
 512static int mt2060_remove(struct i2c_client *client)
 513{
 514        dev_dbg(&client->dev, "\n");
 515
 516        return 0;
 517}
 518
 519static const struct i2c_device_id mt2060_id_table[] = {
 520        {"mt2060", 0},
 521        {}
 522};
 523MODULE_DEVICE_TABLE(i2c, mt2060_id_table);
 524
 525static struct i2c_driver mt2060_driver = {
 526        .driver = {
 527                .name = "mt2060",
 528                .suppress_bind_attrs = true,
 529        },
 530        .probe          = mt2060_probe,
 531        .remove         = mt2060_remove,
 532        .id_table       = mt2060_id_table,
 533};
 534
 535module_i2c_driver(mt2060_driver);
 536
 537MODULE_AUTHOR("Olivier DANET");
 538MODULE_DESCRIPTION("Microtune MT2060 silicon tuner driver");
 539MODULE_LICENSE("GPL");
 540