linux/drivers/bluetooth/hci_bcm.c
<<
>>
Prefs
   1// SPDX-License-Identifier: GPL-2.0-or-later
   2/*
   3 *
   4 *  Bluetooth HCI UART driver for Broadcom devices
   5 *
   6 *  Copyright (C) 2015  Intel Corporation
   7 */
   8
   9#include <linux/kernel.h>
  10#include <linux/errno.h>
  11#include <linux/skbuff.h>
  12#include <linux/firmware.h>
  13#include <linux/module.h>
  14#include <linux/acpi.h>
  15#include <linux/of.h>
  16#include <linux/of_irq.h>
  17#include <linux/property.h>
  18#include <linux/platform_data/x86/apple.h>
  19#include <linux/platform_device.h>
  20#include <linux/regulator/consumer.h>
  21#include <linux/clk.h>
  22#include <linux/gpio/consumer.h>
  23#include <linux/tty.h>
  24#include <linux/interrupt.h>
  25#include <linux/dmi.h>
  26#include <linux/pm_runtime.h>
  27#include <linux/serdev.h>
  28
  29#include <net/bluetooth/bluetooth.h>
  30#include <net/bluetooth/hci_core.h>
  31
  32#include "btbcm.h"
  33#include "hci_uart.h"
  34
  35#define BCM_NULL_PKT 0x00
  36#define BCM_NULL_SIZE 0
  37
  38#define BCM_LM_DIAG_PKT 0x07
  39#define BCM_LM_DIAG_SIZE 63
  40
  41#define BCM_TYPE49_PKT 0x31
  42#define BCM_TYPE49_SIZE 0
  43
  44#define BCM_TYPE52_PKT 0x34
  45#define BCM_TYPE52_SIZE 0
  46
  47#define BCM_AUTOSUSPEND_DELAY   5000 /* default autosleep delay */
  48
  49#define BCM_NUM_SUPPLIES 2
  50
  51/**
  52 * struct bcm_device_data - device specific data
  53 * @no_early_set_baudrate: Disallow set baudrate before driver setup()
  54 * @drive_rts_on_open: drive RTS signal on ->open() when platform requires it
  55 */
  56struct bcm_device_data {
  57        bool    no_early_set_baudrate;
  58        bool    drive_rts_on_open;
  59};
  60
  61/**
  62 * struct bcm_device - device driver resources
  63 * @serdev_hu: HCI UART controller struct
  64 * @list: bcm_device_list node
  65 * @dev: physical UART slave
  66 * @name: device name logged by bt_dev_*() functions
  67 * @device_wakeup: BT_WAKE pin,
  68 *      assert = Bluetooth device must wake up or remain awake,
  69 *      deassert = Bluetooth device may sleep when sleep criteria are met
  70 * @shutdown: BT_REG_ON pin,
  71 *      power up or power down Bluetooth device internal regulators
  72 * @reset: BT_RST_N pin,
  73 *      active low resets the Bluetooth logic core
  74 * @set_device_wakeup: callback to toggle BT_WAKE pin
  75 *      either by accessing @device_wakeup or by calling @btlp
  76 * @set_shutdown: callback to toggle BT_REG_ON pin
  77 *      either by accessing @shutdown or by calling @btpu/@btpd
  78 * @btlp: Apple ACPI method to toggle BT_WAKE pin ("Bluetooth Low Power")
  79 * @btpu: Apple ACPI method to drive BT_REG_ON pin high ("Bluetooth Power Up")
  80 * @btpd: Apple ACPI method to drive BT_REG_ON pin low ("Bluetooth Power Down")
  81 * @gpio_count: internal counter for GPIO resources associated with ACPI device
  82 * @gpio_int_idx: index in _CRS for GpioInt() resource
  83 * @txco_clk: external reference frequency clock used by Bluetooth device
  84 * @lpo_clk: external LPO clock used by Bluetooth device
  85 * @supplies: VBAT and VDDIO supplies used by Bluetooth device
  86 * @res_enabled: whether clocks and supplies are prepared and enabled
  87 * @init_speed: default baudrate of Bluetooth device;
  88 *      the host UART is initially set to this baudrate so that
  89 *      it can configure the Bluetooth device for @oper_speed
  90 * @oper_speed: preferred baudrate of Bluetooth device;
  91 *      set to 0 if @init_speed is already the preferred baudrate
  92 * @irq: interrupt triggered by HOST_WAKE_BT pin
  93 * @irq_active_low: whether @irq is active low
  94 * @irq_acquired: flag to show if IRQ handler has been assigned
  95 * @hu: pointer to HCI UART controller struct,
  96 *      used to disable flow control during runtime suspend and system sleep
  97 * @is_suspended: whether flow control is currently disabled
  98 * @no_early_set_baudrate: don't set_baudrate before setup()
  99 * @drive_rts_on_open: drive RTS signal on ->open() when platform requires it
 100 * @pcm_int_params: keep the initial PCM configuration
 101 */
 102struct bcm_device {
 103        /* Must be the first member, hci_serdev.c expects this. */
 104        struct hci_uart         serdev_hu;
 105        struct list_head        list;
 106
 107        struct device           *dev;
 108
 109        const char              *name;
 110        struct gpio_desc        *device_wakeup;
 111        struct gpio_desc        *shutdown;
 112        struct gpio_desc        *reset;
 113        int                     (*set_device_wakeup)(struct bcm_device *, bool);
 114        int                     (*set_shutdown)(struct bcm_device *, bool);
 115#ifdef CONFIG_ACPI
 116        acpi_handle             btlp, btpu, btpd;
 117        int                     gpio_count;
 118        int                     gpio_int_idx;
 119#endif
 120
 121        struct clk              *txco_clk;
 122        struct clk              *lpo_clk;
 123        struct regulator_bulk_data supplies[BCM_NUM_SUPPLIES];
 124        bool                    res_enabled;
 125
 126        u32                     init_speed;
 127        u32                     oper_speed;
 128        int                     irq;
 129        bool                    irq_active_low;
 130        bool                    irq_acquired;
 131
 132#ifdef CONFIG_PM
 133        struct hci_uart         *hu;
 134        bool                    is_suspended;
 135#endif
 136        bool                    no_early_set_baudrate;
 137        bool                    drive_rts_on_open;
 138        u8                      pcm_int_params[5];
 139};
 140
 141/* generic bcm uart resources */
 142struct bcm_data {
 143        struct sk_buff          *rx_skb;
 144        struct sk_buff_head     txq;
 145
 146        struct bcm_device       *dev;
 147};
 148
 149/* List of BCM BT UART devices */
 150static DEFINE_MUTEX(bcm_device_lock);
 151static LIST_HEAD(bcm_device_list);
 152
 153static int irq_polarity = -1;
 154module_param(irq_polarity, int, 0444);
 155MODULE_PARM_DESC(irq_polarity, "IRQ polarity 0: active-high 1: active-low");
 156
 157static inline void host_set_baudrate(struct hci_uart *hu, unsigned int speed)
 158{
 159        if (hu->serdev)
 160                serdev_device_set_baudrate(hu->serdev, speed);
 161        else
 162                hci_uart_set_baudrate(hu, speed);
 163}
 164
 165static int bcm_set_baudrate(struct hci_uart *hu, unsigned int speed)
 166{
 167        struct hci_dev *hdev = hu->hdev;
 168        struct sk_buff *skb;
 169        struct bcm_update_uart_baud_rate param;
 170
 171        if (speed > 3000000) {
 172                struct bcm_write_uart_clock_setting clock;
 173
 174                clock.type = BCM_UART_CLOCK_48MHZ;
 175
 176                bt_dev_dbg(hdev, "Set Controller clock (%d)", clock.type);
 177
 178                /* This Broadcom specific command changes the UART's controller
 179                 * clock for baud rate > 3000000.
 180                 */
 181                skb = __hci_cmd_sync(hdev, 0xfc45, 1, &clock, HCI_INIT_TIMEOUT);
 182                if (IS_ERR(skb)) {
 183                        int err = PTR_ERR(skb);
 184                        bt_dev_err(hdev, "BCM: failed to write clock (%d)",
 185                                   err);
 186                        return err;
 187                }
 188
 189                kfree_skb(skb);
 190        }
 191
 192        bt_dev_dbg(hdev, "Set Controller UART speed to %d bit/s", speed);
 193
 194        param.zero = cpu_to_le16(0);
 195        param.baud_rate = cpu_to_le32(speed);
 196
 197        /* This Broadcom specific command changes the UART's controller baud
 198         * rate.
 199         */
 200        skb = __hci_cmd_sync(hdev, 0xfc18, sizeof(param), &param,
 201                             HCI_INIT_TIMEOUT);
 202        if (IS_ERR(skb)) {
 203                int err = PTR_ERR(skb);
 204                bt_dev_err(hdev, "BCM: failed to write update baudrate (%d)",
 205                           err);
 206                return err;
 207        }
 208
 209        kfree_skb(skb);
 210
 211        return 0;
 212}
 213
 214/* bcm_device_exists should be protected by bcm_device_lock */
 215static bool bcm_device_exists(struct bcm_device *device)
 216{
 217        struct list_head *p;
 218
 219#ifdef CONFIG_PM
 220        /* Devices using serdev always exist */
 221        if (device && device->hu && device->hu->serdev)
 222                return true;
 223#endif
 224
 225        list_for_each(p, &bcm_device_list) {
 226                struct bcm_device *dev = list_entry(p, struct bcm_device, list);
 227
 228                if (device == dev)
 229                        return true;
 230        }
 231
 232        return false;
 233}
 234
 235static int bcm_gpio_set_power(struct bcm_device *dev, bool powered)
 236{
 237        int err;
 238
 239        if (powered && !dev->res_enabled) {
 240                /* Intel Macs use bcm_apple_get_resources() and don't
 241                 * have regulator supplies configured.
 242                 */
 243                if (dev->supplies[0].supply) {
 244                        err = regulator_bulk_enable(BCM_NUM_SUPPLIES,
 245                                                    dev->supplies);
 246                        if (err)
 247                                return err;
 248                }
 249
 250                /* LPO clock needs to be 32.768 kHz */
 251                err = clk_set_rate(dev->lpo_clk, 32768);
 252                if (err) {
 253                        dev_err(dev->dev, "Could not set LPO clock rate\n");
 254                        goto err_regulator_disable;
 255                }
 256
 257                err = clk_prepare_enable(dev->lpo_clk);
 258                if (err)
 259                        goto err_regulator_disable;
 260
 261                err = clk_prepare_enable(dev->txco_clk);
 262                if (err)
 263                        goto err_lpo_clk_disable;
 264        }
 265
 266        err = dev->set_shutdown(dev, powered);
 267        if (err)
 268                goto err_txco_clk_disable;
 269
 270        err = dev->set_device_wakeup(dev, powered);
 271        if (err)
 272                goto err_revert_shutdown;
 273
 274        if (!powered && dev->res_enabled) {
 275                clk_disable_unprepare(dev->txco_clk);
 276                clk_disable_unprepare(dev->lpo_clk);
 277
 278                /* Intel Macs use bcm_apple_get_resources() and don't
 279                 * have regulator supplies configured.
 280                 */
 281                if (dev->supplies[0].supply)
 282                        regulator_bulk_disable(BCM_NUM_SUPPLIES,
 283                                               dev->supplies);
 284        }
 285
 286        /* wait for device to power on and come out of reset */
 287        usleep_range(100000, 120000);
 288
 289        dev->res_enabled = powered;
 290
 291        return 0;
 292
 293err_revert_shutdown:
 294        dev->set_shutdown(dev, !powered);
 295err_txco_clk_disable:
 296        if (powered && !dev->res_enabled)
 297                clk_disable_unprepare(dev->txco_clk);
 298err_lpo_clk_disable:
 299        if (powered && !dev->res_enabled)
 300                clk_disable_unprepare(dev->lpo_clk);
 301err_regulator_disable:
 302        if (powered && !dev->res_enabled)
 303                regulator_bulk_disable(BCM_NUM_SUPPLIES, dev->supplies);
 304        return err;
 305}
 306
 307#ifdef CONFIG_PM
 308static irqreturn_t bcm_host_wake(int irq, void *data)
 309{
 310        struct bcm_device *bdev = data;
 311
 312        bt_dev_dbg(bdev, "Host wake IRQ");
 313
 314        pm_runtime_get(bdev->dev);
 315        pm_runtime_mark_last_busy(bdev->dev);
 316        pm_runtime_put_autosuspend(bdev->dev);
 317
 318        return IRQ_HANDLED;
 319}
 320
 321static int bcm_request_irq(struct bcm_data *bcm)
 322{
 323        struct bcm_device *bdev = bcm->dev;
 324        int err;
 325
 326        mutex_lock(&bcm_device_lock);
 327        if (!bcm_device_exists(bdev)) {
 328                err = -ENODEV;
 329                goto unlock;
 330        }
 331
 332        if (bdev->irq <= 0) {
 333                err = -EOPNOTSUPP;
 334                goto unlock;
 335        }
 336
 337        err = devm_request_irq(bdev->dev, bdev->irq, bcm_host_wake,
 338                               bdev->irq_active_low ? IRQF_TRIGGER_FALLING :
 339                                                      IRQF_TRIGGER_RISING,
 340                               "host_wake", bdev);
 341        if (err) {
 342                bdev->irq = err;
 343                goto unlock;
 344        }
 345
 346        bdev->irq_acquired = true;
 347
 348        device_init_wakeup(bdev->dev, true);
 349
 350        pm_runtime_set_autosuspend_delay(bdev->dev,
 351                                         BCM_AUTOSUSPEND_DELAY);
 352        pm_runtime_use_autosuspend(bdev->dev);
 353        pm_runtime_set_active(bdev->dev);
 354        pm_runtime_enable(bdev->dev);
 355
 356unlock:
 357        mutex_unlock(&bcm_device_lock);
 358
 359        return err;
 360}
 361
 362static const struct bcm_set_sleep_mode default_sleep_params = {
 363        .sleep_mode = 1,        /* 0=Disabled, 1=UART, 2=Reserved, 3=USB */
 364        .idle_host = 2,         /* idle threshold HOST, in 300ms */
 365        .idle_dev = 2,          /* idle threshold device, in 300ms */
 366        .bt_wake_active = 1,    /* BT_WAKE active mode: 1 = high, 0 = low */
 367        .host_wake_active = 0,  /* HOST_WAKE active mode: 1 = high, 0 = low */
 368        .allow_host_sleep = 1,  /* Allow host sleep in SCO flag */
 369        .combine_modes = 1,     /* Combine sleep and LPM flag */
 370        .tristate_control = 0,  /* Allow tri-state control of UART tx flag */
 371        /* Irrelevant USB flags */
 372        .usb_auto_sleep = 0,
 373        .usb_resume_timeout = 0,
 374        .break_to_host = 0,
 375        .pulsed_host_wake = 1,
 376};
 377
 378static int bcm_setup_sleep(struct hci_uart *hu)
 379{
 380        struct bcm_data *bcm = hu->priv;
 381        struct sk_buff *skb;
 382        struct bcm_set_sleep_mode sleep_params = default_sleep_params;
 383
 384        sleep_params.host_wake_active = !bcm->dev->irq_active_low;
 385
 386        skb = __hci_cmd_sync(hu->hdev, 0xfc27, sizeof(sleep_params),
 387                             &sleep_params, HCI_INIT_TIMEOUT);
 388        if (IS_ERR(skb)) {
 389                int err = PTR_ERR(skb);
 390                bt_dev_err(hu->hdev, "Sleep VSC failed (%d)", err);
 391                return err;
 392        }
 393        kfree_skb(skb);
 394
 395        bt_dev_dbg(hu->hdev, "Set Sleep Parameters VSC succeeded");
 396
 397        return 0;
 398}
 399#else
 400static inline int bcm_request_irq(struct bcm_data *bcm) { return 0; }
 401static inline int bcm_setup_sleep(struct hci_uart *hu) { return 0; }
 402#endif
 403
 404static int bcm_set_diag(struct hci_dev *hdev, bool enable)
 405{
 406        struct hci_uart *hu = hci_get_drvdata(hdev);
 407        struct bcm_data *bcm = hu->priv;
 408        struct sk_buff *skb;
 409
 410        if (!test_bit(HCI_RUNNING, &hdev->flags))
 411                return -ENETDOWN;
 412
 413        skb = bt_skb_alloc(3, GFP_KERNEL);
 414        if (!skb)
 415                return -ENOMEM;
 416
 417        skb_put_u8(skb, BCM_LM_DIAG_PKT);
 418        skb_put_u8(skb, 0xf0);
 419        skb_put_u8(skb, enable);
 420
 421        skb_queue_tail(&bcm->txq, skb);
 422        hci_uart_tx_wakeup(hu);
 423
 424        return 0;
 425}
 426
 427static int bcm_open(struct hci_uart *hu)
 428{
 429        struct bcm_data *bcm;
 430        struct list_head *p;
 431        int err;
 432
 433        bt_dev_dbg(hu->hdev, "hu %p", hu);
 434
 435        if (!hci_uart_has_flow_control(hu))
 436                return -EOPNOTSUPP;
 437
 438        bcm = kzalloc(sizeof(*bcm), GFP_KERNEL);
 439        if (!bcm)
 440                return -ENOMEM;
 441
 442        skb_queue_head_init(&bcm->txq);
 443
 444        hu->priv = bcm;
 445
 446        mutex_lock(&bcm_device_lock);
 447
 448        if (hu->serdev) {
 449                bcm->dev = serdev_device_get_drvdata(hu->serdev);
 450                goto out;
 451        }
 452
 453        if (!hu->tty->dev)
 454                goto out;
 455
 456        list_for_each(p, &bcm_device_list) {
 457                struct bcm_device *dev = list_entry(p, struct bcm_device, list);
 458
 459                /* Retrieve saved bcm_device based on parent of the
 460                 * platform device (saved during device probe) and
 461                 * parent of tty device used by hci_uart
 462                 */
 463                if (hu->tty->dev->parent == dev->dev->parent) {
 464                        bcm->dev = dev;
 465#ifdef CONFIG_PM
 466                        dev->hu = hu;
 467#endif
 468                        break;
 469                }
 470        }
 471
 472out:
 473        if (bcm->dev) {
 474                if (bcm->dev->drive_rts_on_open)
 475                        hci_uart_set_flow_control(hu, true);
 476
 477                hu->init_speed = bcm->dev->init_speed;
 478
 479                /* If oper_speed is set, ldisc/serdev will set the baudrate
 480                 * before calling setup()
 481                 */
 482                if (!bcm->dev->no_early_set_baudrate)
 483                        hu->oper_speed = bcm->dev->oper_speed;
 484
 485                err = bcm_gpio_set_power(bcm->dev, true);
 486
 487                if (bcm->dev->drive_rts_on_open)
 488                        hci_uart_set_flow_control(hu, false);
 489
 490                if (err)
 491                        goto err_unset_hu;
 492        }
 493
 494        mutex_unlock(&bcm_device_lock);
 495        return 0;
 496
 497err_unset_hu:
 498#ifdef CONFIG_PM
 499        if (!hu->serdev)
 500                bcm->dev->hu = NULL;
 501#endif
 502        mutex_unlock(&bcm_device_lock);
 503        hu->priv = NULL;
 504        kfree(bcm);
 505        return err;
 506}
 507
 508static int bcm_close(struct hci_uart *hu)
 509{
 510        struct bcm_data *bcm = hu->priv;
 511        struct bcm_device *bdev = NULL;
 512        int err;
 513
 514        bt_dev_dbg(hu->hdev, "hu %p", hu);
 515
 516        /* Protect bcm->dev against removal of the device or driver */
 517        mutex_lock(&bcm_device_lock);
 518
 519        if (hu->serdev) {
 520                bdev = serdev_device_get_drvdata(hu->serdev);
 521        } else if (bcm_device_exists(bcm->dev)) {
 522                bdev = bcm->dev;
 523#ifdef CONFIG_PM
 524                bdev->hu = NULL;
 525#endif
 526        }
 527
 528        if (bdev) {
 529                if (IS_ENABLED(CONFIG_PM) && bdev->irq_acquired) {
 530                        devm_free_irq(bdev->dev, bdev->irq, bdev);
 531                        device_init_wakeup(bdev->dev, false);
 532                        pm_runtime_disable(bdev->dev);
 533                }
 534
 535                err = bcm_gpio_set_power(bdev, false);
 536                if (err)
 537                        bt_dev_err(hu->hdev, "Failed to power down");
 538                else
 539                        pm_runtime_set_suspended(bdev->dev);
 540        }
 541        mutex_unlock(&bcm_device_lock);
 542
 543        skb_queue_purge(&bcm->txq);
 544        kfree_skb(bcm->rx_skb);
 545        kfree(bcm);
 546
 547        hu->priv = NULL;
 548        return 0;
 549}
 550
 551static int bcm_flush(struct hci_uart *hu)
 552{
 553        struct bcm_data *bcm = hu->priv;
 554
 555        bt_dev_dbg(hu->hdev, "hu %p", hu);
 556
 557        skb_queue_purge(&bcm->txq);
 558
 559        return 0;
 560}
 561
 562static int bcm_setup(struct hci_uart *hu)
 563{
 564        struct bcm_data *bcm = hu->priv;
 565        bool fw_load_done = false;
 566        unsigned int speed;
 567        int err;
 568
 569        bt_dev_dbg(hu->hdev, "hu %p", hu);
 570
 571        hu->hdev->set_diag = bcm_set_diag;
 572        hu->hdev->set_bdaddr = btbcm_set_bdaddr;
 573
 574        err = btbcm_initialize(hu->hdev, &fw_load_done);
 575        if (err)
 576                return err;
 577
 578        if (!fw_load_done)
 579                return 0;
 580
 581        /* Init speed if any */
 582        if (hu->init_speed)
 583                speed = hu->init_speed;
 584        else if (hu->proto->init_speed)
 585                speed = hu->proto->init_speed;
 586        else
 587                speed = 0;
 588
 589        if (speed)
 590                host_set_baudrate(hu, speed);
 591
 592        /* Operational speed if any */
 593        if (hu->oper_speed)
 594                speed = hu->oper_speed;
 595        else if (bcm->dev && bcm->dev->oper_speed)
 596                speed = bcm->dev->oper_speed;
 597        else if (hu->proto->oper_speed)
 598                speed = hu->proto->oper_speed;
 599        else
 600                speed = 0;
 601
 602        if (speed) {
 603                err = bcm_set_baudrate(hu, speed);
 604                if (!err)
 605                        host_set_baudrate(hu, speed);
 606        }
 607
 608        /* PCM parameters if provided */
 609        if (bcm->dev && bcm->dev->pcm_int_params[0] != 0xff) {
 610                struct bcm_set_pcm_int_params params;
 611
 612                btbcm_read_pcm_int_params(hu->hdev, &params);
 613
 614                memcpy(&params, bcm->dev->pcm_int_params, 5);
 615                btbcm_write_pcm_int_params(hu->hdev, &params);
 616        }
 617
 618        err = btbcm_finalize(hu->hdev, &fw_load_done);
 619        if (err)
 620                return err;
 621
 622        /* Some devices ship with the controller default address.
 623         * Allow the bootloader to set a valid address through the
 624         * device tree.
 625         */
 626        set_bit(HCI_QUIRK_USE_BDADDR_PROPERTY, &hu->hdev->quirks);
 627
 628        if (!bcm_request_irq(bcm))
 629                err = bcm_setup_sleep(hu);
 630
 631        return err;
 632}
 633
 634#define BCM_RECV_LM_DIAG \
 635        .type = BCM_LM_DIAG_PKT, \
 636        .hlen = BCM_LM_DIAG_SIZE, \
 637        .loff = 0, \
 638        .lsize = 0, \
 639        .maxlen = BCM_LM_DIAG_SIZE
 640
 641#define BCM_RECV_NULL \
 642        .type = BCM_NULL_PKT, \
 643        .hlen = BCM_NULL_SIZE, \
 644        .loff = 0, \
 645        .lsize = 0, \
 646        .maxlen = BCM_NULL_SIZE
 647
 648#define BCM_RECV_TYPE49 \
 649        .type = BCM_TYPE49_PKT, \
 650        .hlen = BCM_TYPE49_SIZE, \
 651        .loff = 0, \
 652        .lsize = 0, \
 653        .maxlen = BCM_TYPE49_SIZE
 654
 655#define BCM_RECV_TYPE52 \
 656        .type = BCM_TYPE52_PKT, \
 657        .hlen = BCM_TYPE52_SIZE, \
 658        .loff = 0, \
 659        .lsize = 0, \
 660        .maxlen = BCM_TYPE52_SIZE
 661
 662static const struct h4_recv_pkt bcm_recv_pkts[] = {
 663        { H4_RECV_ACL,      .recv = hci_recv_frame },
 664        { H4_RECV_SCO,      .recv = hci_recv_frame },
 665        { H4_RECV_EVENT,    .recv = hci_recv_frame },
 666        { H4_RECV_ISO,      .recv = hci_recv_frame },
 667        { BCM_RECV_LM_DIAG, .recv = hci_recv_diag  },
 668        { BCM_RECV_NULL,    .recv = hci_recv_diag  },
 669        { BCM_RECV_TYPE49,  .recv = hci_recv_diag  },
 670        { BCM_RECV_TYPE52,  .recv = hci_recv_diag  },
 671};
 672
 673static int bcm_recv(struct hci_uart *hu, const void *data, int count)
 674{
 675        struct bcm_data *bcm = hu->priv;
 676
 677        if (!test_bit(HCI_UART_REGISTERED, &hu->flags))
 678                return -EUNATCH;
 679
 680        bcm->rx_skb = h4_recv_buf(hu->hdev, bcm->rx_skb, data, count,
 681                                  bcm_recv_pkts, ARRAY_SIZE(bcm_recv_pkts));
 682        if (IS_ERR(bcm->rx_skb)) {
 683                int err = PTR_ERR(bcm->rx_skb);
 684                bt_dev_err(hu->hdev, "Frame reassembly failed (%d)", err);
 685                bcm->rx_skb = NULL;
 686                return err;
 687        } else if (!bcm->rx_skb) {
 688                /* Delay auto-suspend when receiving completed packet */
 689                mutex_lock(&bcm_device_lock);
 690                if (bcm->dev && bcm_device_exists(bcm->dev)) {
 691                        pm_runtime_get(bcm->dev->dev);
 692                        pm_runtime_mark_last_busy(bcm->dev->dev);
 693                        pm_runtime_put_autosuspend(bcm->dev->dev);
 694                }
 695                mutex_unlock(&bcm_device_lock);
 696        }
 697
 698        return count;
 699}
 700
 701static int bcm_enqueue(struct hci_uart *hu, struct sk_buff *skb)
 702{
 703        struct bcm_data *bcm = hu->priv;
 704
 705        bt_dev_dbg(hu->hdev, "hu %p skb %p", hu, skb);
 706
 707        /* Prepend skb with frame type */
 708        memcpy(skb_push(skb, 1), &hci_skb_pkt_type(skb), 1);
 709        skb_queue_tail(&bcm->txq, skb);
 710
 711        return 0;
 712}
 713
 714static struct sk_buff *bcm_dequeue(struct hci_uart *hu)
 715{
 716        struct bcm_data *bcm = hu->priv;
 717        struct sk_buff *skb = NULL;
 718        struct bcm_device *bdev = NULL;
 719
 720        mutex_lock(&bcm_device_lock);
 721
 722        if (bcm_device_exists(bcm->dev)) {
 723                bdev = bcm->dev;
 724                pm_runtime_get_sync(bdev->dev);
 725                /* Shall be resumed here */
 726        }
 727
 728        skb = skb_dequeue(&bcm->txq);
 729
 730        if (bdev) {
 731                pm_runtime_mark_last_busy(bdev->dev);
 732                pm_runtime_put_autosuspend(bdev->dev);
 733        }
 734
 735        mutex_unlock(&bcm_device_lock);
 736
 737        return skb;
 738}
 739
 740#ifdef CONFIG_PM
 741static int bcm_suspend_device(struct device *dev)
 742{
 743        struct bcm_device *bdev = dev_get_drvdata(dev);
 744        int err;
 745
 746        bt_dev_dbg(bdev, "");
 747
 748        if (!bdev->is_suspended && bdev->hu) {
 749                hci_uart_set_flow_control(bdev->hu, true);
 750
 751                /* Once this returns, driver suspends BT via GPIO */
 752                bdev->is_suspended = true;
 753        }
 754
 755        /* Suspend the device */
 756        err = bdev->set_device_wakeup(bdev, false);
 757        if (err) {
 758                if (bdev->is_suspended && bdev->hu) {
 759                        bdev->is_suspended = false;
 760                        hci_uart_set_flow_control(bdev->hu, false);
 761                }
 762                return -EBUSY;
 763        }
 764
 765        bt_dev_dbg(bdev, "suspend, delaying 15 ms");
 766        msleep(15);
 767
 768        return 0;
 769}
 770
 771static int bcm_resume_device(struct device *dev)
 772{
 773        struct bcm_device *bdev = dev_get_drvdata(dev);
 774        int err;
 775
 776        bt_dev_dbg(bdev, "");
 777
 778        err = bdev->set_device_wakeup(bdev, true);
 779        if (err) {
 780                dev_err(dev, "Failed to power up\n");
 781                return err;
 782        }
 783
 784        bt_dev_dbg(bdev, "resume, delaying 15 ms");
 785        msleep(15);
 786
 787        /* When this executes, the device has woken up already */
 788        if (bdev->is_suspended && bdev->hu) {
 789                bdev->is_suspended = false;
 790
 791                hci_uart_set_flow_control(bdev->hu, false);
 792        }
 793
 794        return 0;
 795}
 796#endif
 797
 798#ifdef CONFIG_PM_SLEEP
 799/* suspend callback */
 800static int bcm_suspend(struct device *dev)
 801{
 802        struct bcm_device *bdev = dev_get_drvdata(dev);
 803        int error;
 804
 805        bt_dev_dbg(bdev, "suspend: is_suspended %d", bdev->is_suspended);
 806
 807        /*
 808         * When used with a device instantiated as platform_device, bcm_suspend
 809         * can be called at any time as long as the platform device is bound,
 810         * so it should use bcm_device_lock to protect access to hci_uart
 811         * and device_wake-up GPIO.
 812         */
 813        mutex_lock(&bcm_device_lock);
 814
 815        if (!bdev->hu)
 816                goto unlock;
 817
 818        if (pm_runtime_active(dev))
 819                bcm_suspend_device(dev);
 820
 821        if (device_may_wakeup(dev) && bdev->irq > 0) {
 822                error = enable_irq_wake(bdev->irq);
 823                if (!error)
 824                        bt_dev_dbg(bdev, "BCM irq: enabled");
 825        }
 826
 827unlock:
 828        mutex_unlock(&bcm_device_lock);
 829
 830        return 0;
 831}
 832
 833/* resume callback */
 834static int bcm_resume(struct device *dev)
 835{
 836        struct bcm_device *bdev = dev_get_drvdata(dev);
 837        int err = 0;
 838
 839        bt_dev_dbg(bdev, "resume: is_suspended %d", bdev->is_suspended);
 840
 841        /*
 842         * When used with a device instantiated as platform_device, bcm_resume
 843         * can be called at any time as long as platform device is bound,
 844         * so it should use bcm_device_lock to protect access to hci_uart
 845         * and device_wake-up GPIO.
 846         */
 847        mutex_lock(&bcm_device_lock);
 848
 849        if (!bdev->hu)
 850                goto unlock;
 851
 852        if (device_may_wakeup(dev) && bdev->irq > 0) {
 853                disable_irq_wake(bdev->irq);
 854                bt_dev_dbg(bdev, "BCM irq: disabled");
 855        }
 856
 857        err = bcm_resume_device(dev);
 858
 859unlock:
 860        mutex_unlock(&bcm_device_lock);
 861
 862        if (!err) {
 863                pm_runtime_disable(dev);
 864                pm_runtime_set_active(dev);
 865                pm_runtime_enable(dev);
 866        }
 867
 868        return 0;
 869}
 870#endif
 871
 872/* Some firmware reports an IRQ which does not work (wrong pin in fw table?) */
 873static const struct dmi_system_id bcm_broken_irq_dmi_table[] = {
 874        {
 875                .ident = "Meegopad T08",
 876                .matches = {
 877                        DMI_EXACT_MATCH(DMI_BOARD_VENDOR,
 878                                        "To be filled by OEM."),
 879                        DMI_EXACT_MATCH(DMI_BOARD_NAME, "T3 MRD"),
 880                        DMI_EXACT_MATCH(DMI_BOARD_VERSION, "V1.1"),
 881                },
 882        },
 883        { }
 884};
 885
 886#ifdef CONFIG_ACPI
 887static const struct acpi_gpio_params first_gpio = { 0, 0, false };
 888static const struct acpi_gpio_params second_gpio = { 1, 0, false };
 889static const struct acpi_gpio_params third_gpio = { 2, 0, false };
 890
 891static const struct acpi_gpio_mapping acpi_bcm_int_last_gpios[] = {
 892        { "device-wakeup-gpios", &first_gpio, 1 },
 893        { "shutdown-gpios", &second_gpio, 1 },
 894        { "host-wakeup-gpios", &third_gpio, 1 },
 895        { },
 896};
 897
 898static const struct acpi_gpio_mapping acpi_bcm_int_first_gpios[] = {
 899        { "host-wakeup-gpios", &first_gpio, 1 },
 900        { "device-wakeup-gpios", &second_gpio, 1 },
 901        { "shutdown-gpios", &third_gpio, 1 },
 902        { },
 903};
 904
 905static int bcm_resource(struct acpi_resource *ares, void *data)
 906{
 907        struct bcm_device *dev = data;
 908        struct acpi_resource_extended_irq *irq;
 909        struct acpi_resource_gpio *gpio;
 910        struct acpi_resource_uart_serialbus *sb;
 911
 912        switch (ares->type) {
 913        case ACPI_RESOURCE_TYPE_EXTENDED_IRQ:
 914                irq = &ares->data.extended_irq;
 915                if (irq->polarity != ACPI_ACTIVE_LOW)
 916                        dev_info(dev->dev, "ACPI Interrupt resource is active-high, this is usually wrong, treating the IRQ as active-low\n");
 917                dev->irq_active_low = true;
 918                break;
 919
 920        case ACPI_RESOURCE_TYPE_GPIO:
 921                gpio = &ares->data.gpio;
 922                if (gpio->connection_type == ACPI_RESOURCE_GPIO_TYPE_INT) {
 923                        dev->gpio_int_idx = dev->gpio_count;
 924                        dev->irq_active_low = gpio->polarity == ACPI_ACTIVE_LOW;
 925                }
 926                dev->gpio_count++;
 927                break;
 928
 929        case ACPI_RESOURCE_TYPE_SERIAL_BUS:
 930                sb = &ares->data.uart_serial_bus;
 931                if (sb->type == ACPI_RESOURCE_SERIAL_TYPE_UART) {
 932                        dev->init_speed = sb->default_baud_rate;
 933                        dev->oper_speed = 4000000;
 934                }
 935                break;
 936
 937        default:
 938                break;
 939        }
 940
 941        return 0;
 942}
 943
 944static int bcm_apple_set_device_wakeup(struct bcm_device *dev, bool awake)
 945{
 946        if (ACPI_FAILURE(acpi_execute_simple_method(dev->btlp, NULL, !awake)))
 947                return -EIO;
 948
 949        return 0;
 950}
 951
 952static int bcm_apple_set_shutdown(struct bcm_device *dev, bool powered)
 953{
 954        if (ACPI_FAILURE(acpi_evaluate_object(powered ? dev->btpu : dev->btpd,
 955                                              NULL, NULL, NULL)))
 956                return -EIO;
 957
 958        return 0;
 959}
 960
 961static int bcm_apple_get_resources(struct bcm_device *dev)
 962{
 963        struct acpi_device *adev = ACPI_COMPANION(dev->dev);
 964        const union acpi_object *obj;
 965
 966        if (!adev ||
 967            ACPI_FAILURE(acpi_get_handle(adev->handle, "BTLP", &dev->btlp)) ||
 968            ACPI_FAILURE(acpi_get_handle(adev->handle, "BTPU", &dev->btpu)) ||
 969            ACPI_FAILURE(acpi_get_handle(adev->handle, "BTPD", &dev->btpd)))
 970                return -ENODEV;
 971
 972        if (!acpi_dev_get_property(adev, "baud", ACPI_TYPE_BUFFER, &obj) &&
 973            obj->buffer.length == 8)
 974                dev->init_speed = *(u64 *)obj->buffer.pointer;
 975
 976        dev->set_device_wakeup = bcm_apple_set_device_wakeup;
 977        dev->set_shutdown = bcm_apple_set_shutdown;
 978
 979        return 0;
 980}
 981#else
 982static inline int bcm_apple_get_resources(struct bcm_device *dev)
 983{
 984        return -EOPNOTSUPP;
 985}
 986#endif /* CONFIG_ACPI */
 987
 988static int bcm_gpio_set_device_wakeup(struct bcm_device *dev, bool awake)
 989{
 990        gpiod_set_value_cansleep(dev->device_wakeup, awake);
 991        return 0;
 992}
 993
 994static int bcm_gpio_set_shutdown(struct bcm_device *dev, bool powered)
 995{
 996        gpiod_set_value_cansleep(dev->shutdown, powered);
 997        if (dev->reset)
 998                /*
 999                 * The reset line is asserted on powerdown and deasserted
1000                 * on poweron so the inverse of powered is used. Notice
1001                 * that the GPIO line BT_RST_N needs to be specified as
1002                 * active low in the device tree or similar system
1003                 * description.
1004                 */
1005                gpiod_set_value_cansleep(dev->reset, !powered);
1006        return 0;
1007}
1008
1009/* Try a bunch of names for TXCO */
1010static struct clk *bcm_get_txco(struct device *dev)
1011{
1012        struct clk *clk;
1013
1014        /* New explicit name */
1015        clk = devm_clk_get(dev, "txco");
1016        if (!IS_ERR(clk) || PTR_ERR(clk) == -EPROBE_DEFER)
1017                return clk;
1018
1019        /* Deprecated name */
1020        clk = devm_clk_get(dev, "extclk");
1021        if (!IS_ERR(clk) || PTR_ERR(clk) == -EPROBE_DEFER)
1022                return clk;
1023
1024        /* Original code used no name at all */
1025        return devm_clk_get(dev, NULL);
1026}
1027
1028static int bcm_get_resources(struct bcm_device *dev)
1029{
1030        const struct dmi_system_id *dmi_id;
1031        int err;
1032
1033        dev->name = dev_name(dev->dev);
1034
1035        if (x86_apple_machine && !bcm_apple_get_resources(dev))
1036                return 0;
1037
1038        dev->txco_clk = bcm_get_txco(dev->dev);
1039
1040        /* Handle deferred probing */
1041        if (dev->txco_clk == ERR_PTR(-EPROBE_DEFER))
1042                return PTR_ERR(dev->txco_clk);
1043
1044        /* Ignore all other errors as before */
1045        if (IS_ERR(dev->txco_clk))
1046                dev->txco_clk = NULL;
1047
1048        dev->lpo_clk = devm_clk_get(dev->dev, "lpo");
1049        if (dev->lpo_clk == ERR_PTR(-EPROBE_DEFER))
1050                return PTR_ERR(dev->lpo_clk);
1051
1052        if (IS_ERR(dev->lpo_clk))
1053                dev->lpo_clk = NULL;
1054
1055        /* Check if we accidentally fetched the lpo clock twice */
1056        if (dev->lpo_clk && clk_is_match(dev->lpo_clk, dev->txco_clk)) {
1057                devm_clk_put(dev->dev, dev->txco_clk);
1058                dev->txco_clk = NULL;
1059        }
1060
1061        dev->device_wakeup = devm_gpiod_get_optional(dev->dev, "device-wakeup",
1062                                                     GPIOD_OUT_LOW);
1063        if (IS_ERR(dev->device_wakeup))
1064                return PTR_ERR(dev->device_wakeup);
1065
1066        dev->shutdown = devm_gpiod_get_optional(dev->dev, "shutdown",
1067                                                GPIOD_OUT_LOW);
1068        if (IS_ERR(dev->shutdown))
1069                return PTR_ERR(dev->shutdown);
1070
1071        dev->reset = devm_gpiod_get_optional(dev->dev, "reset",
1072                                             GPIOD_OUT_LOW);
1073        if (IS_ERR(dev->reset))
1074                return PTR_ERR(dev->reset);
1075
1076        dev->set_device_wakeup = bcm_gpio_set_device_wakeup;
1077        dev->set_shutdown = bcm_gpio_set_shutdown;
1078
1079        dev->supplies[0].supply = "vbat";
1080        dev->supplies[1].supply = "vddio";
1081        err = devm_regulator_bulk_get(dev->dev, BCM_NUM_SUPPLIES,
1082                                      dev->supplies);
1083        if (err)
1084                return err;
1085
1086        /* IRQ can be declared in ACPI table as Interrupt or GpioInt */
1087        if (dev->irq <= 0) {
1088                struct gpio_desc *gpio;
1089
1090                gpio = devm_gpiod_get_optional(dev->dev, "host-wakeup",
1091                                               GPIOD_IN);
1092                if (IS_ERR(gpio))
1093                        return PTR_ERR(gpio);
1094
1095                dev->irq = gpiod_to_irq(gpio);
1096        }
1097
1098        dmi_id = dmi_first_match(bcm_broken_irq_dmi_table);
1099        if (dmi_id) {
1100                dev_info(dev->dev, "%s: Has a broken IRQ config, disabling IRQ support / runtime-pm\n",
1101                         dmi_id->ident);
1102                dev->irq = 0;
1103        }
1104
1105        dev_dbg(dev->dev, "BCM irq: %d\n", dev->irq);
1106        return 0;
1107}
1108
1109#ifdef CONFIG_ACPI
1110static int bcm_acpi_probe(struct bcm_device *dev)
1111{
1112        LIST_HEAD(resources);
1113        const struct acpi_gpio_mapping *gpio_mapping = acpi_bcm_int_last_gpios;
1114        struct resource_entry *entry;
1115        int ret;
1116
1117        /* Retrieve UART ACPI info */
1118        dev->gpio_int_idx = -1;
1119        ret = acpi_dev_get_resources(ACPI_COMPANION(dev->dev),
1120                                     &resources, bcm_resource, dev);
1121        if (ret < 0)
1122                return ret;
1123
1124        resource_list_for_each_entry(entry, &resources) {
1125                if (resource_type(entry->res) == IORESOURCE_IRQ) {
1126                        dev->irq = entry->res->start;
1127                        break;
1128                }
1129        }
1130        acpi_dev_free_resource_list(&resources);
1131
1132        /* If the DSDT uses an Interrupt resource for the IRQ, then there are
1133         * only 2 GPIO resources, we use the irq-last mapping for this, since
1134         * we already have an irq the 3th / last mapping will not be used.
1135         */
1136        if (dev->irq)
1137                gpio_mapping = acpi_bcm_int_last_gpios;
1138        else if (dev->gpio_int_idx == 0)
1139                gpio_mapping = acpi_bcm_int_first_gpios;
1140        else if (dev->gpio_int_idx == 2)
1141                gpio_mapping = acpi_bcm_int_last_gpios;
1142        else
1143                dev_warn(dev->dev, "Unexpected ACPI gpio_int_idx: %d\n",
1144                         dev->gpio_int_idx);
1145
1146        /* Warn if our expectations are not met. */
1147        if (dev->gpio_count != (dev->irq ? 2 : 3))
1148                dev_warn(dev->dev, "Unexpected number of ACPI GPIOs: %d\n",
1149                         dev->gpio_count);
1150
1151        ret = devm_acpi_dev_add_driver_gpios(dev->dev, gpio_mapping);
1152        if (ret)
1153                return ret;
1154
1155        if (irq_polarity != -1) {
1156                dev->irq_active_low = irq_polarity;
1157                dev_warn(dev->dev, "Overwriting IRQ polarity to active %s by module-param\n",
1158                         dev->irq_active_low ? "low" : "high");
1159        }
1160
1161        return 0;
1162}
1163#else
1164static int bcm_acpi_probe(struct bcm_device *dev)
1165{
1166        return -EINVAL;
1167}
1168#endif /* CONFIG_ACPI */
1169
1170static int bcm_of_probe(struct bcm_device *bdev)
1171{
1172        device_property_read_u32(bdev->dev, "max-speed", &bdev->oper_speed);
1173        device_property_read_u8_array(bdev->dev, "brcm,bt-pcm-int-params",
1174                                      bdev->pcm_int_params, 5);
1175        bdev->irq = of_irq_get_byname(bdev->dev->of_node, "host-wakeup");
1176        bdev->irq_active_low = irq_get_trigger_type(bdev->irq)
1177                             & (IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_LEVEL_LOW);
1178        return 0;
1179}
1180
1181static int bcm_probe(struct platform_device *pdev)
1182{
1183        struct bcm_device *dev;
1184        int ret;
1185
1186        dev = devm_kzalloc(&pdev->dev, sizeof(*dev), GFP_KERNEL);
1187        if (!dev)
1188                return -ENOMEM;
1189
1190        dev->dev = &pdev->dev;
1191        dev->irq = platform_get_irq(pdev, 0);
1192
1193        /* Initialize routing field to an unused value */
1194        dev->pcm_int_params[0] = 0xff;
1195
1196        if (has_acpi_companion(&pdev->dev)) {
1197                ret = bcm_acpi_probe(dev);
1198                if (ret)
1199                        return ret;
1200        }
1201
1202        ret = bcm_get_resources(dev);
1203        if (ret)
1204                return ret;
1205
1206        platform_set_drvdata(pdev, dev);
1207
1208        dev_info(&pdev->dev, "%s device registered.\n", dev->name);
1209
1210        /* Place this instance on the device list */
1211        mutex_lock(&bcm_device_lock);
1212        list_add_tail(&dev->list, &bcm_device_list);
1213        mutex_unlock(&bcm_device_lock);
1214
1215        ret = bcm_gpio_set_power(dev, false);
1216        if (ret)
1217                dev_err(&pdev->dev, "Failed to power down\n");
1218
1219        return 0;
1220}
1221
1222static int bcm_remove(struct platform_device *pdev)
1223{
1224        struct bcm_device *dev = platform_get_drvdata(pdev);
1225
1226        mutex_lock(&bcm_device_lock);
1227        list_del(&dev->list);
1228        mutex_unlock(&bcm_device_lock);
1229
1230        dev_info(&pdev->dev, "%s device unregistered.\n", dev->name);
1231
1232        return 0;
1233}
1234
1235static const struct hci_uart_proto bcm_proto = {
1236        .id             = HCI_UART_BCM,
1237        .name           = "Broadcom",
1238        .manufacturer   = 15,
1239        .init_speed     = 115200,
1240        .open           = bcm_open,
1241        .close          = bcm_close,
1242        .flush          = bcm_flush,
1243        .setup          = bcm_setup,
1244        .set_baudrate   = bcm_set_baudrate,
1245        .recv           = bcm_recv,
1246        .enqueue        = bcm_enqueue,
1247        .dequeue        = bcm_dequeue,
1248};
1249
1250#ifdef CONFIG_ACPI
1251static const struct acpi_device_id bcm_acpi_match[] = {
1252        { "BCM2E00" },
1253        { "BCM2E01" },
1254        { "BCM2E02" },
1255        { "BCM2E03" },
1256        { "BCM2E04" },
1257        { "BCM2E05" },
1258        { "BCM2E06" },
1259        { "BCM2E07" },
1260        { "BCM2E08" },
1261        { "BCM2E09" },
1262        { "BCM2E0A" },
1263        { "BCM2E0B" },
1264        { "BCM2E0C" },
1265        { "BCM2E0D" },
1266        { "BCM2E0E" },
1267        { "BCM2E0F" },
1268        { "BCM2E10" },
1269        { "BCM2E11" },
1270        { "BCM2E12" },
1271        { "BCM2E13" },
1272        { "BCM2E14" },
1273        { "BCM2E15" },
1274        { "BCM2E16" },
1275        { "BCM2E17" },
1276        { "BCM2E18" },
1277        { "BCM2E19" },
1278        { "BCM2E1A" },
1279        { "BCM2E1B" },
1280        { "BCM2E1C" },
1281        { "BCM2E1D" },
1282        { "BCM2E1F" },
1283        { "BCM2E20" },
1284        { "BCM2E21" },
1285        { "BCM2E22" },
1286        { "BCM2E23" },
1287        { "BCM2E24" },
1288        { "BCM2E25" },
1289        { "BCM2E26" },
1290        { "BCM2E27" },
1291        { "BCM2E28" },
1292        { "BCM2E29" },
1293        { "BCM2E2A" },
1294        { "BCM2E2B" },
1295        { "BCM2E2C" },
1296        { "BCM2E2D" },
1297        { "BCM2E2E" },
1298        { "BCM2E2F" },
1299        { "BCM2E30" },
1300        { "BCM2E31" },
1301        { "BCM2E32" },
1302        { "BCM2E33" },
1303        { "BCM2E34" },
1304        { "BCM2E35" },
1305        { "BCM2E36" },
1306        { "BCM2E37" },
1307        { "BCM2E38" },
1308        { "BCM2E39" },
1309        { "BCM2E3A" },
1310        { "BCM2E3B" },
1311        { "BCM2E3C" },
1312        { "BCM2E3D" },
1313        { "BCM2E3E" },
1314        { "BCM2E3F" },
1315        { "BCM2E40" },
1316        { "BCM2E41" },
1317        { "BCM2E42" },
1318        { "BCM2E43" },
1319        { "BCM2E44" },
1320        { "BCM2E45" },
1321        { "BCM2E46" },
1322        { "BCM2E47" },
1323        { "BCM2E48" },
1324        { "BCM2E49" },
1325        { "BCM2E4A" },
1326        { "BCM2E4B" },
1327        { "BCM2E4C" },
1328        { "BCM2E4D" },
1329        { "BCM2E4E" },
1330        { "BCM2E4F" },
1331        { "BCM2E50" },
1332        { "BCM2E51" },
1333        { "BCM2E52" },
1334        { "BCM2E53" },
1335        { "BCM2E54" },
1336        { "BCM2E55" },
1337        { "BCM2E56" },
1338        { "BCM2E57" },
1339        { "BCM2E58" },
1340        { "BCM2E59" },
1341        { "BCM2E5A" },
1342        { "BCM2E5B" },
1343        { "BCM2E5C" },
1344        { "BCM2E5D" },
1345        { "BCM2E5E" },
1346        { "BCM2E5F" },
1347        { "BCM2E60" },
1348        { "BCM2E61" },
1349        { "BCM2E62" },
1350        { "BCM2E63" },
1351        { "BCM2E64" },
1352        { "BCM2E65" },
1353        { "BCM2E66" },
1354        { "BCM2E67" },
1355        { "BCM2E68" },
1356        { "BCM2E69" },
1357        { "BCM2E6B" },
1358        { "BCM2E6D" },
1359        { "BCM2E6E" },
1360        { "BCM2E6F" },
1361        { "BCM2E70" },
1362        { "BCM2E71" },
1363        { "BCM2E72" },
1364        { "BCM2E73" },
1365        { "BCM2E74" },
1366        { "BCM2E75" },
1367        { "BCM2E76" },
1368        { "BCM2E77" },
1369        { "BCM2E78" },
1370        { "BCM2E79" },
1371        { "BCM2E7A" },
1372        { "BCM2E7B" },
1373        { "BCM2E7C" },
1374        { "BCM2E7D" },
1375        { "BCM2E7E" },
1376        { "BCM2E7F" },
1377        { "BCM2E80" },
1378        { "BCM2E81" },
1379        { "BCM2E82" },
1380        { "BCM2E83" },
1381        { "BCM2E84" },
1382        { "BCM2E85" },
1383        { "BCM2E86" },
1384        { "BCM2E87" },
1385        { "BCM2E88" },
1386        { "BCM2E89" },
1387        { "BCM2E8A" },
1388        { "BCM2E8B" },
1389        { "BCM2E8C" },
1390        { "BCM2E8D" },
1391        { "BCM2E8E" },
1392        { "BCM2E90" },
1393        { "BCM2E92" },
1394        { "BCM2E93" },
1395        { "BCM2E94" },
1396        { "BCM2E95" },
1397        { "BCM2E96" },
1398        { "BCM2E97" },
1399        { "BCM2E98" },
1400        { "BCM2E99" },
1401        { "BCM2E9A" },
1402        { "BCM2E9B" },
1403        { "BCM2E9C" },
1404        { "BCM2E9D" },
1405        { "BCM2EA0" },
1406        { "BCM2EA1" },
1407        { "BCM2EA2" },
1408        { "BCM2EA3" },
1409        { "BCM2EA4" },
1410        { "BCM2EA5" },
1411        { "BCM2EA6" },
1412        { "BCM2EA7" },
1413        { "BCM2EA8" },
1414        { "BCM2EA9" },
1415        { "BCM2EAA" },
1416        { "BCM2EAB" },
1417        { "BCM2EAC" },
1418        { },
1419};
1420MODULE_DEVICE_TABLE(acpi, bcm_acpi_match);
1421#endif
1422
1423/* suspend and resume callbacks */
1424static const struct dev_pm_ops bcm_pm_ops = {
1425        SET_SYSTEM_SLEEP_PM_OPS(bcm_suspend, bcm_resume)
1426        SET_RUNTIME_PM_OPS(bcm_suspend_device, bcm_resume_device, NULL)
1427};
1428
1429static struct platform_driver bcm_driver = {
1430        .probe = bcm_probe,
1431        .remove = bcm_remove,
1432        .driver = {
1433                .name = "hci_bcm",
1434                .acpi_match_table = ACPI_PTR(bcm_acpi_match),
1435                .pm = &bcm_pm_ops,
1436        },
1437};
1438
1439static int bcm_serdev_probe(struct serdev_device *serdev)
1440{
1441        struct bcm_device *bcmdev;
1442        const struct bcm_device_data *data;
1443        int err;
1444
1445        bcmdev = devm_kzalloc(&serdev->dev, sizeof(*bcmdev), GFP_KERNEL);
1446        if (!bcmdev)
1447                return -ENOMEM;
1448
1449        bcmdev->dev = &serdev->dev;
1450#ifdef CONFIG_PM
1451        bcmdev->hu = &bcmdev->serdev_hu;
1452#endif
1453        bcmdev->serdev_hu.serdev = serdev;
1454        serdev_device_set_drvdata(serdev, bcmdev);
1455
1456        /* Initialize routing field to an unused value */
1457        bcmdev->pcm_int_params[0] = 0xff;
1458
1459        if (has_acpi_companion(&serdev->dev))
1460                err = bcm_acpi_probe(bcmdev);
1461        else
1462                err = bcm_of_probe(bcmdev);
1463        if (err)
1464                return err;
1465
1466        err = bcm_get_resources(bcmdev);
1467        if (err)
1468                return err;
1469
1470        if (!bcmdev->shutdown) {
1471                dev_warn(&serdev->dev,
1472                         "No reset resource, using default baud rate\n");
1473                bcmdev->oper_speed = bcmdev->init_speed;
1474        }
1475
1476        err = bcm_gpio_set_power(bcmdev, false);
1477        if (err)
1478                dev_err(&serdev->dev, "Failed to power down\n");
1479
1480        data = device_get_match_data(bcmdev->dev);
1481        if (data) {
1482                bcmdev->no_early_set_baudrate = data->no_early_set_baudrate;
1483                bcmdev->drive_rts_on_open = data->drive_rts_on_open;
1484        }
1485
1486        return hci_uart_register_device(&bcmdev->serdev_hu, &bcm_proto);
1487}
1488
1489static void bcm_serdev_remove(struct serdev_device *serdev)
1490{
1491        struct bcm_device *bcmdev = serdev_device_get_drvdata(serdev);
1492
1493        hci_uart_unregister_device(&bcmdev->serdev_hu);
1494}
1495
1496#ifdef CONFIG_OF
1497static struct bcm_device_data bcm4354_device_data = {
1498        .no_early_set_baudrate = true,
1499};
1500
1501static struct bcm_device_data bcm43438_device_data = {
1502        .drive_rts_on_open = true,
1503};
1504
1505static const struct of_device_id bcm_bluetooth_of_match[] = {
1506        { .compatible = "brcm,bcm20702a1" },
1507        { .compatible = "brcm,bcm4329-bt" },
1508        { .compatible = "brcm,bcm4330-bt" },
1509        { .compatible = "brcm,bcm4334-bt" },
1510        { .compatible = "brcm,bcm4345c5" },
1511        { .compatible = "brcm,bcm4330-bt" },
1512        { .compatible = "brcm,bcm43438-bt", .data = &bcm43438_device_data },
1513        { .compatible = "brcm,bcm43540-bt", .data = &bcm4354_device_data },
1514        { .compatible = "brcm,bcm4335a0" },
1515        { },
1516};
1517MODULE_DEVICE_TABLE(of, bcm_bluetooth_of_match);
1518#endif
1519
1520static struct serdev_device_driver bcm_serdev_driver = {
1521        .probe = bcm_serdev_probe,
1522        .remove = bcm_serdev_remove,
1523        .driver = {
1524                .name = "hci_uart_bcm",
1525                .of_match_table = of_match_ptr(bcm_bluetooth_of_match),
1526                .acpi_match_table = ACPI_PTR(bcm_acpi_match),
1527                .pm = &bcm_pm_ops,
1528        },
1529};
1530
1531int __init bcm_init(void)
1532{
1533        /* For now, we need to keep both platform device
1534         * driver (ACPI generated) and serdev driver (DT).
1535         */
1536        platform_driver_register(&bcm_driver);
1537        serdev_device_driver_register(&bcm_serdev_driver);
1538
1539        return hci_uart_register_proto(&bcm_proto);
1540}
1541
1542int __exit bcm_deinit(void)
1543{
1544        platform_driver_unregister(&bcm_driver);
1545        serdev_device_driver_unregister(&bcm_serdev_driver);
1546
1547        return hci_uart_unregister_proto(&bcm_proto);
1548}
1549