linux/drivers/hwmon/w83792d.c
<<
>>
Prefs
   1// SPDX-License-Identifier: GPL-2.0-or-later
   2/*
   3 * w83792d.c - Part of lm_sensors, Linux kernel modules for hardware
   4 *             monitoring
   5 * Copyright (C) 2004, 2005 Winbond Electronics Corp.
   6 *                          Shane Huang,
   7 *                          Rudolf Marek <r.marek@assembler.cz>
   8 *
   9 * Note:
  10 * 1. This driver is only for 2.6 kernel, 2.4 kernel need a different driver.
  11 * 2. This driver is only for Winbond W83792D C version device, there
  12 *     are also some motherboards with B version W83792D device. The
  13 *     calculation method to in6-in7(measured value, limits) is a little
  14 *     different between C and B version. C or B version can be identified
  15 *     by CR[0x49h].
  16 */
  17
  18/*
  19 * Supports following chips:
  20 *
  21 * Chip         #vin    #fanin  #pwm    #temp   wchipid vendid  i2c     ISA
  22 * w83792d      9       7       7       3       0x7a    0x5ca3  yes     no
  23 */
  24
  25#include <linux/module.h>
  26#include <linux/init.h>
  27#include <linux/slab.h>
  28#include <linux/i2c.h>
  29#include <linux/hwmon.h>
  30#include <linux/hwmon-sysfs.h>
  31#include <linux/err.h>
  32#include <linux/mutex.h>
  33#include <linux/sysfs.h>
  34#include <linux/jiffies.h>
  35
  36/* Addresses to scan */
  37static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f,
  38                                                I2C_CLIENT_END };
  39
  40/* Insmod parameters */
  41
  42static unsigned short force_subclients[4];
  43module_param_array(force_subclients, short, NULL, 0);
  44MODULE_PARM_DESC(force_subclients,
  45                 "List of subclient addresses: {bus, clientaddr, subclientaddr1, subclientaddr2}");
  46
  47static bool init;
  48module_param(init, bool, 0);
  49MODULE_PARM_DESC(init, "Set to one to force chip initialization");
  50
  51/* The W83792D registers */
  52static const u8 W83792D_REG_IN[9] = {
  53        0x20,   /* Vcore A in DataSheet */
  54        0x21,   /* Vcore B in DataSheet */
  55        0x22,   /* VIN0 in DataSheet */
  56        0x23,   /* VIN1 in DataSheet */
  57        0x24,   /* VIN2 in DataSheet */
  58        0x25,   /* VIN3 in DataSheet */
  59        0x26,   /* 5VCC in DataSheet */
  60        0xB0,   /* 5VSB in DataSheet */
  61        0xB1    /* VBAT in DataSheet */
  62};
  63#define W83792D_REG_LOW_BITS1 0x3E  /* Low Bits I in DataSheet */
  64#define W83792D_REG_LOW_BITS2 0x3F  /* Low Bits II in DataSheet */
  65static const u8 W83792D_REG_IN_MAX[9] = {
  66        0x2B,   /* Vcore A High Limit in DataSheet */
  67        0x2D,   /* Vcore B High Limit in DataSheet */
  68        0x2F,   /* VIN0 High Limit in DataSheet */
  69        0x31,   /* VIN1 High Limit in DataSheet */
  70        0x33,   /* VIN2 High Limit in DataSheet */
  71        0x35,   /* VIN3 High Limit in DataSheet */
  72        0x37,   /* 5VCC High Limit in DataSheet */
  73        0xB4,   /* 5VSB High Limit in DataSheet */
  74        0xB6    /* VBAT High Limit in DataSheet */
  75};
  76static const u8 W83792D_REG_IN_MIN[9] = {
  77        0x2C,   /* Vcore A Low Limit in DataSheet */
  78        0x2E,   /* Vcore B Low Limit in DataSheet */
  79        0x30,   /* VIN0 Low Limit in DataSheet */
  80        0x32,   /* VIN1 Low Limit in DataSheet */
  81        0x34,   /* VIN2 Low Limit in DataSheet */
  82        0x36,   /* VIN3 Low Limit in DataSheet */
  83        0x38,   /* 5VCC Low Limit in DataSheet */
  84        0xB5,   /* 5VSB Low Limit in DataSheet */
  85        0xB7    /* VBAT Low Limit in DataSheet */
  86};
  87static const u8 W83792D_REG_FAN[7] = {
  88        0x28,   /* FAN 1 Count in DataSheet */
  89        0x29,   /* FAN 2 Count in DataSheet */
  90        0x2A,   /* FAN 3 Count in DataSheet */
  91        0xB8,   /* FAN 4 Count in DataSheet */
  92        0xB9,   /* FAN 5 Count in DataSheet */
  93        0xBA,   /* FAN 6 Count in DataSheet */
  94        0xBE    /* FAN 7 Count in DataSheet */
  95};
  96static const u8 W83792D_REG_FAN_MIN[7] = {
  97        0x3B,   /* FAN 1 Count Low Limit in DataSheet */
  98        0x3C,   /* FAN 2 Count Low Limit in DataSheet */
  99        0x3D,   /* FAN 3 Count Low Limit in DataSheet */
 100        0xBB,   /* FAN 4 Count Low Limit in DataSheet */
 101        0xBC,   /* FAN 5 Count Low Limit in DataSheet */
 102        0xBD,   /* FAN 6 Count Low Limit in DataSheet */
 103        0xBF    /* FAN 7 Count Low Limit in DataSheet */
 104};
 105#define W83792D_REG_FAN_CFG 0x84        /* FAN Configuration in DataSheet */
 106static const u8 W83792D_REG_FAN_DIV[4] = {
 107        0x47,   /* contains FAN2 and FAN1 Divisor */
 108        0x5B,   /* contains FAN4 and FAN3 Divisor */
 109        0x5C,   /* contains FAN6 and FAN5 Divisor */
 110        0x9E    /* contains FAN7 Divisor. */
 111};
 112static const u8 W83792D_REG_PWM[7] = {
 113        0x81,   /* FAN 1 Duty Cycle, be used to control */
 114        0x83,   /* FAN 2 Duty Cycle, be used to control */
 115        0x94,   /* FAN 3 Duty Cycle, be used to control */
 116        0xA3,   /* FAN 4 Duty Cycle, be used to control */
 117        0xA4,   /* FAN 5 Duty Cycle, be used to control */
 118        0xA5,   /* FAN 6 Duty Cycle, be used to control */
 119        0xA6    /* FAN 7 Duty Cycle, be used to control */
 120};
 121#define W83792D_REG_BANK                0x4E
 122#define W83792D_REG_TEMP2_CONFIG        0xC2
 123#define W83792D_REG_TEMP3_CONFIG        0xCA
 124
 125static const u8 W83792D_REG_TEMP1[3] = {
 126        0x27,   /* TEMP 1 in DataSheet */
 127        0x39,   /* TEMP 1 Over in DataSheet */
 128        0x3A,   /* TEMP 1 Hyst in DataSheet */
 129};
 130
 131static const u8 W83792D_REG_TEMP_ADD[2][6] = {
 132        { 0xC0,         /* TEMP 2 in DataSheet */
 133          0xC1,         /* TEMP 2(0.5 deg) in DataSheet */
 134          0xC5,         /* TEMP 2 Over High part in DataSheet */
 135          0xC6,         /* TEMP 2 Over Low part in DataSheet */
 136          0xC3,         /* TEMP 2 Thyst High part in DataSheet */
 137          0xC4 },       /* TEMP 2 Thyst Low part in DataSheet */
 138        { 0xC8,         /* TEMP 3 in DataSheet */
 139          0xC9,         /* TEMP 3(0.5 deg) in DataSheet */
 140          0xCD,         /* TEMP 3 Over High part in DataSheet */
 141          0xCE,         /* TEMP 3 Over Low part in DataSheet */
 142          0xCB,         /* TEMP 3 Thyst High part in DataSheet */
 143          0xCC }        /* TEMP 3 Thyst Low part in DataSheet */
 144};
 145
 146static const u8 W83792D_REG_THERMAL[3] = {
 147        0x85,   /* SmartFanI: Fan1 target value */
 148        0x86,   /* SmartFanI: Fan2 target value */
 149        0x96    /* SmartFanI: Fan3 target value */
 150};
 151
 152static const u8 W83792D_REG_TOLERANCE[3] = {
 153        0x87,   /* (bit3-0)SmartFan Fan1 tolerance */
 154        0x87,   /* (bit7-4)SmartFan Fan2 tolerance */
 155        0x97    /* (bit3-0)SmartFan Fan3 tolerance */
 156};
 157
 158static const u8 W83792D_REG_POINTS[3][4] = {
 159        { 0x85,         /* SmartFanII: Fan1 temp point 1 */
 160          0xE3,         /* SmartFanII: Fan1 temp point 2 */
 161          0xE4,         /* SmartFanII: Fan1 temp point 3 */
 162          0xE5 },       /* SmartFanII: Fan1 temp point 4 */
 163        { 0x86,         /* SmartFanII: Fan2 temp point 1 */
 164          0xE6,         /* SmartFanII: Fan2 temp point 2 */
 165          0xE7,         /* SmartFanII: Fan2 temp point 3 */
 166          0xE8 },       /* SmartFanII: Fan2 temp point 4 */
 167        { 0x96,         /* SmartFanII: Fan3 temp point 1 */
 168          0xE9,         /* SmartFanII: Fan3 temp point 2 */
 169          0xEA,         /* SmartFanII: Fan3 temp point 3 */
 170          0xEB }        /* SmartFanII: Fan3 temp point 4 */
 171};
 172
 173static const u8 W83792D_REG_LEVELS[3][4] = {
 174        { 0x88,         /* (bit3-0) SmartFanII: Fan1 Non-Stop */
 175          0x88,         /* (bit7-4) SmartFanII: Fan1 Level 1 */
 176          0xE0,         /* (bit7-4) SmartFanII: Fan1 Level 2 */
 177          0xE0 },       /* (bit3-0) SmartFanII: Fan1 Level 3 */
 178        { 0x89,         /* (bit3-0) SmartFanII: Fan2 Non-Stop */
 179          0x89,         /* (bit7-4) SmartFanII: Fan2 Level 1 */
 180          0xE1,         /* (bit7-4) SmartFanII: Fan2 Level 2 */
 181          0xE1 },       /* (bit3-0) SmartFanII: Fan2 Level 3 */
 182        { 0x98,         /* (bit3-0) SmartFanII: Fan3 Non-Stop */
 183          0x98,         /* (bit7-4) SmartFanII: Fan3 Level 1 */
 184          0xE2,         /* (bit7-4) SmartFanII: Fan3 Level 2 */
 185          0xE2 }        /* (bit3-0) SmartFanII: Fan3 Level 3 */
 186};
 187
 188#define W83792D_REG_GPIO_EN             0x1A
 189#define W83792D_REG_CONFIG              0x40
 190#define W83792D_REG_VID_FANDIV          0x47
 191#define W83792D_REG_CHIPID              0x49
 192#define W83792D_REG_WCHIPID             0x58
 193#define W83792D_REG_CHIPMAN             0x4F
 194#define W83792D_REG_PIN                 0x4B
 195#define W83792D_REG_I2C_SUBADDR         0x4A
 196
 197#define W83792D_REG_ALARM1 0xA9         /* realtime status register1 */
 198#define W83792D_REG_ALARM2 0xAA         /* realtime status register2 */
 199#define W83792D_REG_ALARM3 0xAB         /* realtime status register3 */
 200#define W83792D_REG_CHASSIS 0x42        /* Bit 5: Case Open status bit */
 201#define W83792D_REG_CHASSIS_CLR 0x44    /* Bit 7: Case Open CLR_CHS/Reset bit */
 202
 203/* control in0/in1 's limit modifiability */
 204#define W83792D_REG_VID_IN_B            0x17
 205
 206#define W83792D_REG_VBAT                0x5D
 207#define W83792D_REG_I2C_ADDR            0x48
 208
 209/*
 210 * Conversions. Rounding and limit checking is only done on the TO_REG
 211 * variants. Note that you should be a bit careful with which arguments
 212 * these macros are called: arguments may be evaluated more than once.
 213 * Fixing this is just not worth it.
 214 */
 215#define IN_FROM_REG(nr, val) (((nr) <= 1) ? ((val) * 2) : \
 216                ((((nr) == 6) || ((nr) == 7)) ? ((val) * 6) : ((val) * 4)))
 217#define IN_TO_REG(nr, val) (((nr) <= 1) ? ((val) / 2) : \
 218                ((((nr) == 6) || ((nr) == 7)) ? ((val) / 6) : ((val) / 4)))
 219
 220static inline u8
 221FAN_TO_REG(long rpm, int div)
 222{
 223        if (rpm == 0)
 224                return 255;
 225        rpm = clamp_val(rpm, 1, 1000000);
 226        return clamp_val((1350000 + rpm * div / 2) / (rpm * div), 1, 254);
 227}
 228
 229#define FAN_FROM_REG(val, div)  ((val) == 0   ? -1 : \
 230                                ((val) == 255 ? 0 : \
 231                                                1350000 / ((val) * (div))))
 232
 233/* for temp1 */
 234#define TEMP1_TO_REG(val)       (clamp_val(((val) < 0 ? (val) + 0x100 * 1000 \
 235                                                      : (val)) / 1000, 0, 0xff))
 236#define TEMP1_FROM_REG(val)     (((val) & 0x80 ? (val)-0x100 : (val)) * 1000)
 237/* for temp2 and temp3, because they need additional resolution */
 238#define TEMP_ADD_FROM_REG(val1, val2) \
 239        ((((val1) & 0x80 ? (val1)-0x100 \
 240                : (val1)) * 1000) + ((val2 & 0x80) ? 500 : 0))
 241#define TEMP_ADD_TO_REG_HIGH(val) \
 242        (clamp_val(((val) < 0 ? (val) + 0x100 * 1000 : (val)) / 1000, 0, 0xff))
 243#define TEMP_ADD_TO_REG_LOW(val)        ((val%1000) ? 0x80 : 0x00)
 244
 245#define DIV_FROM_REG(val)               (1 << (val))
 246
 247static inline u8
 248DIV_TO_REG(long val)
 249{
 250        int i;
 251        val = clamp_val(val, 1, 128) >> 1;
 252        for (i = 0; i < 7; i++) {
 253                if (val == 0)
 254                        break;
 255                val >>= 1;
 256        }
 257        return (u8)i;
 258}
 259
 260struct w83792d_data {
 261        struct device *hwmon_dev;
 262
 263        struct mutex update_lock;
 264        char valid;             /* !=0 if following fields are valid */
 265        unsigned long last_updated;     /* In jiffies */
 266
 267        u8 in[9];               /* Register value */
 268        u8 in_max[9];           /* Register value */
 269        u8 in_min[9];           /* Register value */
 270        u16 low_bits;           /* Additional resolution to voltage in6-0 */
 271        u8 fan[7];              /* Register value */
 272        u8 fan_min[7];          /* Register value */
 273        u8 temp1[3];            /* current, over, thyst */
 274        u8 temp_add[2][6];      /* Register value */
 275        u8 fan_div[7];          /* Register encoding, shifted right */
 276        u8 pwm[7];              /* The 7 PWM outputs */
 277        u8 pwmenable[3];
 278        u32 alarms;             /* realtime status register encoding,combined */
 279        u8 chassis;             /* Chassis status */
 280        u8 thermal_cruise[3];   /* Smart FanI: Fan1,2,3 target value */
 281        u8 tolerance[3];        /* Fan1,2,3 tolerance(Smart Fan I/II) */
 282        u8 sf2_points[3][4];    /* Smart FanII: Fan1,2,3 temperature points */
 283        u8 sf2_levels[3][4];    /* Smart FanII: Fan1,2,3 duty cycle levels */
 284};
 285
 286static int w83792d_probe(struct i2c_client *client);
 287static int w83792d_detect(struct i2c_client *client,
 288                          struct i2c_board_info *info);
 289static int w83792d_remove(struct i2c_client *client);
 290static struct w83792d_data *w83792d_update_device(struct device *dev);
 291
 292#ifdef DEBUG
 293static void w83792d_print_debug(struct w83792d_data *data, struct device *dev);
 294#endif
 295
 296static void w83792d_init_client(struct i2c_client *client);
 297
 298static const struct i2c_device_id w83792d_id[] = {
 299        { "w83792d", 0 },
 300        { }
 301};
 302MODULE_DEVICE_TABLE(i2c, w83792d_id);
 303
 304static struct i2c_driver w83792d_driver = {
 305        .class          = I2C_CLASS_HWMON,
 306        .driver = {
 307                .name = "w83792d",
 308        },
 309        .probe_new      = w83792d_probe,
 310        .remove         = w83792d_remove,
 311        .id_table       = w83792d_id,
 312        .detect         = w83792d_detect,
 313        .address_list   = normal_i2c,
 314};
 315
 316static inline long in_count_from_reg(int nr, struct w83792d_data *data)
 317{
 318        /* in7 and in8 do not have low bits, but the formula still works */
 319        return (data->in[nr] << 2) | ((data->low_bits >> (2 * nr)) & 0x03);
 320}
 321
 322/*
 323 * The SMBus locks itself. The Winbond W83792D chip has a bank register,
 324 * but the driver only accesses registers in bank 0, so we don't have
 325 * to switch banks and lock access between switches.
 326 */
 327static inline int w83792d_read_value(struct i2c_client *client, u8 reg)
 328{
 329        return i2c_smbus_read_byte_data(client, reg);
 330}
 331
 332static inline int
 333w83792d_write_value(struct i2c_client *client, u8 reg, u8 value)
 334{
 335        return i2c_smbus_write_byte_data(client, reg, value);
 336}
 337
 338/* following are the sysfs callback functions */
 339static ssize_t show_in(struct device *dev, struct device_attribute *attr,
 340                        char *buf)
 341{
 342        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 343        int nr = sensor_attr->index;
 344        struct w83792d_data *data = w83792d_update_device(dev);
 345        return sprintf(buf, "%ld\n",
 346                       IN_FROM_REG(nr, in_count_from_reg(nr, data)));
 347}
 348
 349#define show_in_reg(reg) \
 350static ssize_t show_##reg(struct device *dev, struct device_attribute *attr, \
 351                        char *buf) \
 352{ \
 353        struct sensor_device_attribute *sensor_attr \
 354                = to_sensor_dev_attr(attr); \
 355        int nr = sensor_attr->index; \
 356        struct w83792d_data *data = w83792d_update_device(dev); \
 357        return sprintf(buf, "%ld\n", \
 358                       (long)(IN_FROM_REG(nr, data->reg[nr]) * 4)); \
 359}
 360
 361show_in_reg(in_min);
 362show_in_reg(in_max);
 363
 364#define store_in_reg(REG, reg) \
 365static ssize_t store_in_##reg(struct device *dev, \
 366                                struct device_attribute *attr, \
 367                                const char *buf, size_t count) \
 368{ \
 369        struct sensor_device_attribute *sensor_attr \
 370                        = to_sensor_dev_attr(attr); \
 371        int nr = sensor_attr->index; \
 372        struct i2c_client *client = to_i2c_client(dev); \
 373        struct w83792d_data *data = i2c_get_clientdata(client); \
 374        unsigned long val; \
 375        int err = kstrtoul(buf, 10, &val); \
 376        if (err) \
 377                return err; \
 378        mutex_lock(&data->update_lock); \
 379        data->in_##reg[nr] = clamp_val(IN_TO_REG(nr, val) / 4, 0, 255); \
 380        w83792d_write_value(client, W83792D_REG_IN_##REG[nr], \
 381                            data->in_##reg[nr]); \
 382        mutex_unlock(&data->update_lock); \
 383         \
 384        return count; \
 385}
 386store_in_reg(MIN, min);
 387store_in_reg(MAX, max);
 388
 389#define show_fan_reg(reg) \
 390static ssize_t show_##reg(struct device *dev, struct device_attribute *attr, \
 391                        char *buf) \
 392{ \
 393        struct sensor_device_attribute *sensor_attr \
 394                        = to_sensor_dev_attr(attr); \
 395        int nr = sensor_attr->index - 1; \
 396        struct w83792d_data *data = w83792d_update_device(dev); \
 397        return sprintf(buf, "%d\n", \
 398                FAN_FROM_REG(data->reg[nr], DIV_FROM_REG(data->fan_div[nr]))); \
 399}
 400
 401show_fan_reg(fan);
 402show_fan_reg(fan_min);
 403
 404static ssize_t
 405store_fan_min(struct device *dev, struct device_attribute *attr,
 406                const char *buf, size_t count)
 407{
 408        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 409        int nr = sensor_attr->index - 1;
 410        struct i2c_client *client = to_i2c_client(dev);
 411        struct w83792d_data *data = i2c_get_clientdata(client);
 412        unsigned long val;
 413        int err;
 414
 415        err = kstrtoul(buf, 10, &val);
 416        if (err)
 417                return err;
 418
 419        mutex_lock(&data->update_lock);
 420        data->fan_min[nr] = FAN_TO_REG(val, DIV_FROM_REG(data->fan_div[nr]));
 421        w83792d_write_value(client, W83792D_REG_FAN_MIN[nr],
 422                                data->fan_min[nr]);
 423        mutex_unlock(&data->update_lock);
 424
 425        return count;
 426}
 427
 428static ssize_t
 429show_fan_div(struct device *dev, struct device_attribute *attr,
 430                char *buf)
 431{
 432        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 433        int nr = sensor_attr->index;
 434        struct w83792d_data *data = w83792d_update_device(dev);
 435        return sprintf(buf, "%u\n", DIV_FROM_REG(data->fan_div[nr - 1]));
 436}
 437
 438/*
 439 * Note: we save and restore the fan minimum here, because its value is
 440 * determined in part by the fan divisor.  This follows the principle of
 441 * least surprise; the user doesn't expect the fan minimum to change just
 442 * because the divisor changed.
 443 */
 444static ssize_t
 445store_fan_div(struct device *dev, struct device_attribute *attr,
 446                const char *buf, size_t count)
 447{
 448        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 449        int nr = sensor_attr->index - 1;
 450        struct i2c_client *client = to_i2c_client(dev);
 451        struct w83792d_data *data = i2c_get_clientdata(client);
 452        unsigned long min;
 453        /*u8 reg;*/
 454        u8 fan_div_reg = 0;
 455        u8 tmp_fan_div;
 456        unsigned long val;
 457        int err;
 458
 459        err = kstrtoul(buf, 10, &val);
 460        if (err)
 461                return err;
 462
 463        /* Save fan_min */
 464        mutex_lock(&data->update_lock);
 465        min = FAN_FROM_REG(data->fan_min[nr],
 466                           DIV_FROM_REG(data->fan_div[nr]));
 467
 468        data->fan_div[nr] = DIV_TO_REG(val);
 469
 470        fan_div_reg = w83792d_read_value(client, W83792D_REG_FAN_DIV[nr >> 1]);
 471        fan_div_reg &= (nr & 0x01) ? 0x8f : 0xf8;
 472        tmp_fan_div = (nr & 0x01) ? (((data->fan_div[nr]) << 4) & 0x70)
 473                                        : ((data->fan_div[nr]) & 0x07);
 474        w83792d_write_value(client, W83792D_REG_FAN_DIV[nr >> 1],
 475                                        fan_div_reg | tmp_fan_div);
 476
 477        /* Restore fan_min */
 478        data->fan_min[nr] = FAN_TO_REG(min, DIV_FROM_REG(data->fan_div[nr]));
 479        w83792d_write_value(client, W83792D_REG_FAN_MIN[nr], data->fan_min[nr]);
 480        mutex_unlock(&data->update_lock);
 481
 482        return count;
 483}
 484
 485/* read/write the temperature1, includes measured value and limits */
 486
 487static ssize_t show_temp1(struct device *dev, struct device_attribute *attr,
 488                                char *buf)
 489{
 490        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 491        int nr = sensor_attr->index;
 492        struct w83792d_data *data = w83792d_update_device(dev);
 493        return sprintf(buf, "%d\n", TEMP1_FROM_REG(data->temp1[nr]));
 494}
 495
 496static ssize_t store_temp1(struct device *dev, struct device_attribute *attr,
 497                                const char *buf, size_t count)
 498{
 499        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 500        int nr = sensor_attr->index;
 501        struct i2c_client *client = to_i2c_client(dev);
 502        struct w83792d_data *data = i2c_get_clientdata(client);
 503        long val;
 504        int err;
 505
 506        err = kstrtol(buf, 10, &val);
 507        if (err)
 508                return err;
 509
 510        mutex_lock(&data->update_lock);
 511        data->temp1[nr] = TEMP1_TO_REG(val);
 512        w83792d_write_value(client, W83792D_REG_TEMP1[nr],
 513                data->temp1[nr]);
 514        mutex_unlock(&data->update_lock);
 515
 516        return count;
 517}
 518
 519/* read/write the temperature2-3, includes measured value and limits */
 520
 521static ssize_t show_temp23(struct device *dev, struct device_attribute *attr,
 522                                char *buf)
 523{
 524        struct sensor_device_attribute_2 *sensor_attr
 525          = to_sensor_dev_attr_2(attr);
 526        int nr = sensor_attr->nr;
 527        int index = sensor_attr->index;
 528        struct w83792d_data *data = w83792d_update_device(dev);
 529        return sprintf(buf, "%ld\n",
 530                (long)TEMP_ADD_FROM_REG(data->temp_add[nr][index],
 531                        data->temp_add[nr][index+1]));
 532}
 533
 534static ssize_t store_temp23(struct device *dev, struct device_attribute *attr,
 535                                const char *buf, size_t count)
 536{
 537        struct sensor_device_attribute_2 *sensor_attr
 538          = to_sensor_dev_attr_2(attr);
 539        int nr = sensor_attr->nr;
 540        int index = sensor_attr->index;
 541        struct i2c_client *client = to_i2c_client(dev);
 542        struct w83792d_data *data = i2c_get_clientdata(client);
 543        long val;
 544        int err;
 545
 546        err = kstrtol(buf, 10, &val);
 547        if (err)
 548                return err;
 549
 550        mutex_lock(&data->update_lock);
 551        data->temp_add[nr][index] = TEMP_ADD_TO_REG_HIGH(val);
 552        data->temp_add[nr][index+1] = TEMP_ADD_TO_REG_LOW(val);
 553        w83792d_write_value(client, W83792D_REG_TEMP_ADD[nr][index],
 554                data->temp_add[nr][index]);
 555        w83792d_write_value(client, W83792D_REG_TEMP_ADD[nr][index+1],
 556                data->temp_add[nr][index+1]);
 557        mutex_unlock(&data->update_lock);
 558
 559        return count;
 560}
 561
 562/* get realtime status of all sensors items: voltage, temp, fan */
 563static ssize_t
 564alarms_show(struct device *dev, struct device_attribute *attr, char *buf)
 565{
 566        struct w83792d_data *data = w83792d_update_device(dev);
 567        return sprintf(buf, "%d\n", data->alarms);
 568}
 569
 570static ssize_t show_alarm(struct device *dev,
 571                          struct device_attribute *attr, char *buf)
 572{
 573        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 574        int nr = sensor_attr->index;
 575        struct w83792d_data *data = w83792d_update_device(dev);
 576        return sprintf(buf, "%d\n", (data->alarms >> nr) & 1);
 577}
 578
 579static ssize_t
 580show_pwm(struct device *dev, struct device_attribute *attr,
 581                char *buf)
 582{
 583        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 584        int nr = sensor_attr->index;
 585        struct w83792d_data *data = w83792d_update_device(dev);
 586        return sprintf(buf, "%d\n", (data->pwm[nr] & 0x0f) << 4);
 587}
 588
 589static ssize_t
 590show_pwmenable(struct device *dev, struct device_attribute *attr,
 591                        char *buf)
 592{
 593        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 594        int nr = sensor_attr->index - 1;
 595        struct w83792d_data *data = w83792d_update_device(dev);
 596        long pwm_enable_tmp = 1;
 597
 598        switch (data->pwmenable[nr]) {
 599        case 0:
 600                pwm_enable_tmp = 1; /* manual mode */
 601                break;
 602        case 1:
 603                pwm_enable_tmp = 3; /*thermal cruise/Smart Fan I */
 604                break;
 605        case 2:
 606                pwm_enable_tmp = 2; /* Smart Fan II */
 607                break;
 608        }
 609
 610        return sprintf(buf, "%ld\n", pwm_enable_tmp);
 611}
 612
 613static ssize_t
 614store_pwm(struct device *dev, struct device_attribute *attr,
 615                const char *buf, size_t count)
 616{
 617        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 618        int nr = sensor_attr->index;
 619        struct i2c_client *client = to_i2c_client(dev);
 620        struct w83792d_data *data = i2c_get_clientdata(client);
 621        unsigned long val;
 622        int err;
 623
 624        err = kstrtoul(buf, 10, &val);
 625        if (err)
 626                return err;
 627        val = clamp_val(val, 0, 255) >> 4;
 628
 629        mutex_lock(&data->update_lock);
 630        val |= w83792d_read_value(client, W83792D_REG_PWM[nr]) & 0xf0;
 631        data->pwm[nr] = val;
 632        w83792d_write_value(client, W83792D_REG_PWM[nr], data->pwm[nr]);
 633        mutex_unlock(&data->update_lock);
 634
 635        return count;
 636}
 637
 638static ssize_t
 639store_pwmenable(struct device *dev, struct device_attribute *attr,
 640                        const char *buf, size_t count)
 641{
 642        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 643        int nr = sensor_attr->index - 1;
 644        struct i2c_client *client = to_i2c_client(dev);
 645        struct w83792d_data *data = i2c_get_clientdata(client);
 646        u8 fan_cfg_tmp, cfg1_tmp, cfg2_tmp, cfg3_tmp, cfg4_tmp;
 647        unsigned long val;
 648        int err;
 649
 650        err = kstrtoul(buf, 10, &val);
 651        if (err)
 652                return err;
 653
 654        if (val < 1 || val > 3)
 655                return -EINVAL;
 656
 657        mutex_lock(&data->update_lock);
 658        switch (val) {
 659        case 1:
 660                data->pwmenable[nr] = 0; /* manual mode */
 661                break;
 662        case 2:
 663                data->pwmenable[nr] = 2; /* Smart Fan II */
 664                break;
 665        case 3:
 666                data->pwmenable[nr] = 1; /* thermal cruise/Smart Fan I */
 667                break;
 668        }
 669        cfg1_tmp = data->pwmenable[0];
 670        cfg2_tmp = (data->pwmenable[1]) << 2;
 671        cfg3_tmp = (data->pwmenable[2]) << 4;
 672        cfg4_tmp = w83792d_read_value(client, W83792D_REG_FAN_CFG) & 0xc0;
 673        fan_cfg_tmp = ((cfg4_tmp | cfg3_tmp) | cfg2_tmp) | cfg1_tmp;
 674        w83792d_write_value(client, W83792D_REG_FAN_CFG, fan_cfg_tmp);
 675        mutex_unlock(&data->update_lock);
 676
 677        return count;
 678}
 679
 680static ssize_t
 681show_pwm_mode(struct device *dev, struct device_attribute *attr,
 682                        char *buf)
 683{
 684        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 685        int nr = sensor_attr->index;
 686        struct w83792d_data *data = w83792d_update_device(dev);
 687        return sprintf(buf, "%d\n", data->pwm[nr] >> 7);
 688}
 689
 690static ssize_t
 691store_pwm_mode(struct device *dev, struct device_attribute *attr,
 692                        const char *buf, size_t count)
 693{
 694        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 695        int nr = sensor_attr->index;
 696        struct i2c_client *client = to_i2c_client(dev);
 697        struct w83792d_data *data = i2c_get_clientdata(client);
 698        unsigned long val;
 699        int err;
 700
 701        err = kstrtoul(buf, 10, &val);
 702        if (err)
 703                return err;
 704        if (val > 1)
 705                return -EINVAL;
 706
 707        mutex_lock(&data->update_lock);
 708        data->pwm[nr] = w83792d_read_value(client, W83792D_REG_PWM[nr]);
 709        if (val) {                      /* PWM mode */
 710                data->pwm[nr] |= 0x80;
 711        } else {                        /* DC mode */
 712                data->pwm[nr] &= 0x7f;
 713        }
 714        w83792d_write_value(client, W83792D_REG_PWM[nr], data->pwm[nr]);
 715        mutex_unlock(&data->update_lock);
 716
 717        return count;
 718}
 719
 720static ssize_t
 721intrusion0_alarm_show(struct device *dev, struct device_attribute *attr,
 722                      char *buf)
 723{
 724        struct w83792d_data *data = w83792d_update_device(dev);
 725        return sprintf(buf, "%d\n", data->chassis);
 726}
 727
 728static ssize_t
 729intrusion0_alarm_store(struct device *dev, struct device_attribute *attr,
 730                       const char *buf, size_t count)
 731{
 732        struct i2c_client *client = to_i2c_client(dev);
 733        struct w83792d_data *data = i2c_get_clientdata(client);
 734        unsigned long val;
 735        u8 reg;
 736
 737        if (kstrtoul(buf, 10, &val) || val != 0)
 738                return -EINVAL;
 739
 740        mutex_lock(&data->update_lock);
 741        reg = w83792d_read_value(client, W83792D_REG_CHASSIS_CLR);
 742        w83792d_write_value(client, W83792D_REG_CHASSIS_CLR, reg | 0x80);
 743        data->valid = 0;                /* Force cache refresh */
 744        mutex_unlock(&data->update_lock);
 745
 746        return count;
 747}
 748
 749/* For Smart Fan I / Thermal Cruise */
 750static ssize_t
 751show_thermal_cruise(struct device *dev, struct device_attribute *attr,
 752                        char *buf)
 753{
 754        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 755        int nr = sensor_attr->index;
 756        struct w83792d_data *data = w83792d_update_device(dev);
 757        return sprintf(buf, "%ld\n", (long)data->thermal_cruise[nr-1]);
 758}
 759
 760static ssize_t
 761store_thermal_cruise(struct device *dev, struct device_attribute *attr,
 762                        const char *buf, size_t count)
 763{
 764        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 765        int nr = sensor_attr->index - 1;
 766        struct i2c_client *client = to_i2c_client(dev);
 767        struct w83792d_data *data = i2c_get_clientdata(client);
 768        u8 target_tmp = 0, target_mask = 0;
 769        unsigned long val;
 770        int err;
 771
 772        err = kstrtoul(buf, 10, &val);
 773        if (err)
 774                return err;
 775
 776        target_tmp = val;
 777        target_tmp = target_tmp & 0x7f;
 778        mutex_lock(&data->update_lock);
 779        target_mask = w83792d_read_value(client,
 780                                         W83792D_REG_THERMAL[nr]) & 0x80;
 781        data->thermal_cruise[nr] = clamp_val(target_tmp, 0, 255);
 782        w83792d_write_value(client, W83792D_REG_THERMAL[nr],
 783                (data->thermal_cruise[nr]) | target_mask);
 784        mutex_unlock(&data->update_lock);
 785
 786        return count;
 787}
 788
 789/* For Smart Fan I/Thermal Cruise and Smart Fan II */
 790static ssize_t
 791show_tolerance(struct device *dev, struct device_attribute *attr,
 792                char *buf)
 793{
 794        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 795        int nr = sensor_attr->index;
 796        struct w83792d_data *data = w83792d_update_device(dev);
 797        return sprintf(buf, "%ld\n", (long)data->tolerance[nr-1]);
 798}
 799
 800static ssize_t
 801store_tolerance(struct device *dev, struct device_attribute *attr,
 802                const char *buf, size_t count)
 803{
 804        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 805        int nr = sensor_attr->index - 1;
 806        struct i2c_client *client = to_i2c_client(dev);
 807        struct w83792d_data *data = i2c_get_clientdata(client);
 808        u8 tol_tmp, tol_mask;
 809        unsigned long val;
 810        int err;
 811
 812        err = kstrtoul(buf, 10, &val);
 813        if (err)
 814                return err;
 815
 816        mutex_lock(&data->update_lock);
 817        tol_mask = w83792d_read_value(client,
 818                W83792D_REG_TOLERANCE[nr]) & ((nr == 1) ? 0x0f : 0xf0);
 819        tol_tmp = clamp_val(val, 0, 15);
 820        tol_tmp &= 0x0f;
 821        data->tolerance[nr] = tol_tmp;
 822        if (nr == 1)
 823                tol_tmp <<= 4;
 824        w83792d_write_value(client, W83792D_REG_TOLERANCE[nr],
 825                tol_mask | tol_tmp);
 826        mutex_unlock(&data->update_lock);
 827
 828        return count;
 829}
 830
 831/* For Smart Fan II */
 832static ssize_t
 833show_sf2_point(struct device *dev, struct device_attribute *attr,
 834                char *buf)
 835{
 836        struct sensor_device_attribute_2 *sensor_attr
 837          = to_sensor_dev_attr_2(attr);
 838        int nr = sensor_attr->nr;
 839        int index = sensor_attr->index;
 840        struct w83792d_data *data = w83792d_update_device(dev);
 841        return sprintf(buf, "%ld\n", (long)data->sf2_points[index-1][nr-1]);
 842}
 843
 844static ssize_t
 845store_sf2_point(struct device *dev, struct device_attribute *attr,
 846                const char *buf, size_t count)
 847{
 848        struct sensor_device_attribute_2 *sensor_attr
 849          = to_sensor_dev_attr_2(attr);
 850        int nr = sensor_attr->nr - 1;
 851        int index = sensor_attr->index - 1;
 852        struct i2c_client *client = to_i2c_client(dev);
 853        struct w83792d_data *data = i2c_get_clientdata(client);
 854        u8 mask_tmp = 0;
 855        unsigned long val;
 856        int err;
 857
 858        err = kstrtoul(buf, 10, &val);
 859        if (err)
 860                return err;
 861
 862        mutex_lock(&data->update_lock);
 863        data->sf2_points[index][nr] = clamp_val(val, 0, 127);
 864        mask_tmp = w83792d_read_value(client,
 865                                        W83792D_REG_POINTS[index][nr]) & 0x80;
 866        w83792d_write_value(client, W83792D_REG_POINTS[index][nr],
 867                mask_tmp|data->sf2_points[index][nr]);
 868        mutex_unlock(&data->update_lock);
 869
 870        return count;
 871}
 872
 873static ssize_t
 874show_sf2_level(struct device *dev, struct device_attribute *attr,
 875                char *buf)
 876{
 877        struct sensor_device_attribute_2 *sensor_attr
 878          = to_sensor_dev_attr_2(attr);
 879        int nr = sensor_attr->nr;
 880        int index = sensor_attr->index;
 881        struct w83792d_data *data = w83792d_update_device(dev);
 882        return sprintf(buf, "%d\n",
 883                        (((data->sf2_levels[index-1][nr]) * 100) / 15));
 884}
 885
 886static ssize_t
 887store_sf2_level(struct device *dev, struct device_attribute *attr,
 888                const char *buf, size_t count)
 889{
 890        struct sensor_device_attribute_2 *sensor_attr
 891          = to_sensor_dev_attr_2(attr);
 892        int nr = sensor_attr->nr;
 893        int index = sensor_attr->index - 1;
 894        struct i2c_client *client = to_i2c_client(dev);
 895        struct w83792d_data *data = i2c_get_clientdata(client);
 896        u8 mask_tmp = 0, level_tmp = 0;
 897        unsigned long val;
 898        int err;
 899
 900        err = kstrtoul(buf, 10, &val);
 901        if (err)
 902                return err;
 903
 904        mutex_lock(&data->update_lock);
 905        data->sf2_levels[index][nr] = clamp_val((val * 15) / 100, 0, 15);
 906        mask_tmp = w83792d_read_value(client, W83792D_REG_LEVELS[index][nr])
 907                & ((nr == 3) ? 0xf0 : 0x0f);
 908        if (nr == 3)
 909                level_tmp = data->sf2_levels[index][nr];
 910        else
 911                level_tmp = data->sf2_levels[index][nr] << 4;
 912        w83792d_write_value(client, W83792D_REG_LEVELS[index][nr],
 913                            level_tmp | mask_tmp);
 914        mutex_unlock(&data->update_lock);
 915
 916        return count;
 917}
 918
 919
 920static int
 921w83792d_detect_subclients(struct i2c_client *new_client)
 922{
 923        int i, id;
 924        int address = new_client->addr;
 925        u8 val;
 926        struct i2c_adapter *adapter = new_client->adapter;
 927
 928        id = i2c_adapter_id(adapter);
 929        if (force_subclients[0] == id && force_subclients[1] == address) {
 930                for (i = 2; i <= 3; i++) {
 931                        if (force_subclients[i] < 0x48 ||
 932                            force_subclients[i] > 0x4f) {
 933                                dev_err(&new_client->dev,
 934                                        "invalid subclient address %d; must be 0x48-0x4f\n",
 935                                        force_subclients[i]);
 936                                return -ENODEV;
 937                        }
 938                }
 939                w83792d_write_value(new_client, W83792D_REG_I2C_SUBADDR,
 940                                        (force_subclients[2] & 0x07) |
 941                                        ((force_subclients[3] & 0x07) << 4));
 942        }
 943
 944        val = w83792d_read_value(new_client, W83792D_REG_I2C_SUBADDR);
 945
 946        if (!(val & 0x88) && (val & 0x7) == ((val >> 4) & 0x7)) {
 947                dev_err(&new_client->dev,
 948                        "duplicate addresses 0x%x, use force_subclient\n", 0x48 + (val & 0x7));
 949                return -ENODEV;
 950        }
 951
 952        if (!(val & 0x08))
 953                devm_i2c_new_dummy_device(&new_client->dev, adapter, 0x48 + (val & 0x7));
 954
 955        if (!(val & 0x80))
 956                devm_i2c_new_dummy_device(&new_client->dev, adapter, 0x48 + ((val >> 4) & 0x7));
 957
 958        return 0;
 959}
 960
 961static SENSOR_DEVICE_ATTR(in0_input, S_IRUGO, show_in, NULL, 0);
 962static SENSOR_DEVICE_ATTR(in1_input, S_IRUGO, show_in, NULL, 1);
 963static SENSOR_DEVICE_ATTR(in2_input, S_IRUGO, show_in, NULL, 2);
 964static SENSOR_DEVICE_ATTR(in3_input, S_IRUGO, show_in, NULL, 3);
 965static SENSOR_DEVICE_ATTR(in4_input, S_IRUGO, show_in, NULL, 4);
 966static SENSOR_DEVICE_ATTR(in5_input, S_IRUGO, show_in, NULL, 5);
 967static SENSOR_DEVICE_ATTR(in6_input, S_IRUGO, show_in, NULL, 6);
 968static SENSOR_DEVICE_ATTR(in7_input, S_IRUGO, show_in, NULL, 7);
 969static SENSOR_DEVICE_ATTR(in8_input, S_IRUGO, show_in, NULL, 8);
 970static SENSOR_DEVICE_ATTR(in0_min, S_IWUSR | S_IRUGO,
 971                        show_in_min, store_in_min, 0);
 972static SENSOR_DEVICE_ATTR(in1_min, S_IWUSR | S_IRUGO,
 973                        show_in_min, store_in_min, 1);
 974static SENSOR_DEVICE_ATTR(in2_min, S_IWUSR | S_IRUGO,
 975                        show_in_min, store_in_min, 2);
 976static SENSOR_DEVICE_ATTR(in3_min, S_IWUSR | S_IRUGO,
 977                        show_in_min, store_in_min, 3);
 978static SENSOR_DEVICE_ATTR(in4_min, S_IWUSR | S_IRUGO,
 979                        show_in_min, store_in_min, 4);
 980static SENSOR_DEVICE_ATTR(in5_min, S_IWUSR | S_IRUGO,
 981                        show_in_min, store_in_min, 5);
 982static SENSOR_DEVICE_ATTR(in6_min, S_IWUSR | S_IRUGO,
 983                        show_in_min, store_in_min, 6);
 984static SENSOR_DEVICE_ATTR(in7_min, S_IWUSR | S_IRUGO,
 985                        show_in_min, store_in_min, 7);
 986static SENSOR_DEVICE_ATTR(in8_min, S_IWUSR | S_IRUGO,
 987                        show_in_min, store_in_min, 8);
 988static SENSOR_DEVICE_ATTR(in0_max, S_IWUSR | S_IRUGO,
 989                        show_in_max, store_in_max, 0);
 990static SENSOR_DEVICE_ATTR(in1_max, S_IWUSR | S_IRUGO,
 991                        show_in_max, store_in_max, 1);
 992static SENSOR_DEVICE_ATTR(in2_max, S_IWUSR | S_IRUGO,
 993                        show_in_max, store_in_max, 2);
 994static SENSOR_DEVICE_ATTR(in3_max, S_IWUSR | S_IRUGO,
 995                        show_in_max, store_in_max, 3);
 996static SENSOR_DEVICE_ATTR(in4_max, S_IWUSR | S_IRUGO,
 997                        show_in_max, store_in_max, 4);
 998static SENSOR_DEVICE_ATTR(in5_max, S_IWUSR | S_IRUGO,
 999                        show_in_max, store_in_max, 5);
1000static SENSOR_DEVICE_ATTR(in6_max, S_IWUSR | S_IRUGO,
1001                        show_in_max, store_in_max, 6);
1002static SENSOR_DEVICE_ATTR(in7_max, S_IWUSR | S_IRUGO,
1003                        show_in_max, store_in_max, 7);
1004static SENSOR_DEVICE_ATTR(in8_max, S_IWUSR | S_IRUGO,
1005                        show_in_max, store_in_max, 8);
1006static SENSOR_DEVICE_ATTR_2(temp1_input, S_IRUGO, show_temp1, NULL, 0, 0);
1007static SENSOR_DEVICE_ATTR_2(temp2_input, S_IRUGO, show_temp23, NULL, 0, 0);
1008static SENSOR_DEVICE_ATTR_2(temp3_input, S_IRUGO, show_temp23, NULL, 1, 0);
1009static SENSOR_DEVICE_ATTR_2(temp1_max, S_IRUGO | S_IWUSR,
1010                        show_temp1, store_temp1, 0, 1);
1011static SENSOR_DEVICE_ATTR_2(temp2_max, S_IRUGO | S_IWUSR, show_temp23,
1012                        store_temp23, 0, 2);
1013static SENSOR_DEVICE_ATTR_2(temp3_max, S_IRUGO | S_IWUSR, show_temp23,
1014                        store_temp23, 1, 2);
1015static SENSOR_DEVICE_ATTR_2(temp1_max_hyst, S_IRUGO | S_IWUSR,
1016                        show_temp1, store_temp1, 0, 2);
1017static SENSOR_DEVICE_ATTR_2(temp2_max_hyst, S_IRUGO | S_IWUSR,
1018                        show_temp23, store_temp23, 0, 4);
1019static SENSOR_DEVICE_ATTR_2(temp3_max_hyst, S_IRUGO | S_IWUSR,
1020                        show_temp23, store_temp23, 1, 4);
1021static DEVICE_ATTR_RO(alarms);
1022static SENSOR_DEVICE_ATTR(in0_alarm, S_IRUGO, show_alarm, NULL, 0);
1023static SENSOR_DEVICE_ATTR(in1_alarm, S_IRUGO, show_alarm, NULL, 1);
1024static SENSOR_DEVICE_ATTR(temp1_alarm, S_IRUGO, show_alarm, NULL, 2);
1025static SENSOR_DEVICE_ATTR(temp2_alarm, S_IRUGO, show_alarm, NULL, 3);
1026static SENSOR_DEVICE_ATTR(temp3_alarm, S_IRUGO, show_alarm, NULL, 4);
1027static SENSOR_DEVICE_ATTR(fan1_alarm, S_IRUGO, show_alarm, NULL, 5);
1028static SENSOR_DEVICE_ATTR(fan2_alarm, S_IRUGO, show_alarm, NULL, 6);
1029static SENSOR_DEVICE_ATTR(fan3_alarm, S_IRUGO, show_alarm, NULL, 7);
1030static SENSOR_DEVICE_ATTR(in2_alarm, S_IRUGO, show_alarm, NULL, 8);
1031static SENSOR_DEVICE_ATTR(in3_alarm, S_IRUGO, show_alarm, NULL, 9);
1032static SENSOR_DEVICE_ATTR(in4_alarm, S_IRUGO, show_alarm, NULL, 10);
1033static SENSOR_DEVICE_ATTR(in5_alarm, S_IRUGO, show_alarm, NULL, 11);
1034static SENSOR_DEVICE_ATTR(in6_alarm, S_IRUGO, show_alarm, NULL, 12);
1035static SENSOR_DEVICE_ATTR(fan7_alarm, S_IRUGO, show_alarm, NULL, 15);
1036static SENSOR_DEVICE_ATTR(in7_alarm, S_IRUGO, show_alarm, NULL, 19);
1037static SENSOR_DEVICE_ATTR(in8_alarm, S_IRUGO, show_alarm, NULL, 20);
1038static SENSOR_DEVICE_ATTR(fan4_alarm, S_IRUGO, show_alarm, NULL, 21);
1039static SENSOR_DEVICE_ATTR(fan5_alarm, S_IRUGO, show_alarm, NULL, 22);
1040static SENSOR_DEVICE_ATTR(fan6_alarm, S_IRUGO, show_alarm, NULL, 23);
1041static DEVICE_ATTR_RW(intrusion0_alarm);
1042static SENSOR_DEVICE_ATTR(pwm1, S_IWUSR | S_IRUGO, show_pwm, store_pwm, 0);
1043static SENSOR_DEVICE_ATTR(pwm2, S_IWUSR | S_IRUGO, show_pwm, store_pwm, 1);
1044static SENSOR_DEVICE_ATTR(pwm3, S_IWUSR | S_IRUGO, show_pwm, store_pwm, 2);
1045static SENSOR_DEVICE_ATTR(pwm4, S_IWUSR | S_IRUGO, show_pwm, store_pwm, 3);
1046static SENSOR_DEVICE_ATTR(pwm5, S_IWUSR | S_IRUGO, show_pwm, store_pwm, 4);
1047static SENSOR_DEVICE_ATTR(pwm6, S_IWUSR | S_IRUGO, show_pwm, store_pwm, 5);
1048static SENSOR_DEVICE_ATTR(pwm7, S_IWUSR | S_IRUGO, show_pwm, store_pwm, 6);
1049static SENSOR_DEVICE_ATTR(pwm1_enable, S_IWUSR | S_IRUGO,
1050                        show_pwmenable, store_pwmenable, 1);
1051static SENSOR_DEVICE_ATTR(pwm2_enable, S_IWUSR | S_IRUGO,
1052                        show_pwmenable, store_pwmenable, 2);
1053static SENSOR_DEVICE_ATTR(pwm3_enable, S_IWUSR | S_IRUGO,
1054                        show_pwmenable, store_pwmenable, 3);
1055static SENSOR_DEVICE_ATTR(pwm1_mode, S_IWUSR | S_IRUGO,
1056                        show_pwm_mode, store_pwm_mode, 0);
1057static SENSOR_DEVICE_ATTR(pwm2_mode, S_IWUSR | S_IRUGO,
1058                        show_pwm_mode, store_pwm_mode, 1);
1059static SENSOR_DEVICE_ATTR(pwm3_mode, S_IWUSR | S_IRUGO,
1060                        show_pwm_mode, store_pwm_mode, 2);
1061static SENSOR_DEVICE_ATTR(pwm4_mode, S_IWUSR | S_IRUGO,
1062                        show_pwm_mode, store_pwm_mode, 3);
1063static SENSOR_DEVICE_ATTR(pwm5_mode, S_IWUSR | S_IRUGO,
1064                        show_pwm_mode, store_pwm_mode, 4);
1065static SENSOR_DEVICE_ATTR(pwm6_mode, S_IWUSR | S_IRUGO,
1066                        show_pwm_mode, store_pwm_mode, 5);
1067static SENSOR_DEVICE_ATTR(pwm7_mode, S_IWUSR | S_IRUGO,
1068                        show_pwm_mode, store_pwm_mode, 6);
1069static SENSOR_DEVICE_ATTR(tolerance1, S_IWUSR | S_IRUGO,
1070                        show_tolerance, store_tolerance, 1);
1071static SENSOR_DEVICE_ATTR(tolerance2, S_IWUSR | S_IRUGO,
1072                        show_tolerance, store_tolerance, 2);
1073static SENSOR_DEVICE_ATTR(tolerance3, S_IWUSR | S_IRUGO,
1074                        show_tolerance, store_tolerance, 3);
1075static SENSOR_DEVICE_ATTR(thermal_cruise1, S_IWUSR | S_IRUGO,
1076                        show_thermal_cruise, store_thermal_cruise, 1);
1077static SENSOR_DEVICE_ATTR(thermal_cruise2, S_IWUSR | S_IRUGO,
1078                        show_thermal_cruise, store_thermal_cruise, 2);
1079static SENSOR_DEVICE_ATTR(thermal_cruise3, S_IWUSR | S_IRUGO,
1080                        show_thermal_cruise, store_thermal_cruise, 3);
1081static SENSOR_DEVICE_ATTR_2(sf2_point1_fan1, S_IRUGO | S_IWUSR,
1082                        show_sf2_point, store_sf2_point, 1, 1);
1083static SENSOR_DEVICE_ATTR_2(sf2_point2_fan1, S_IRUGO | S_IWUSR,
1084                        show_sf2_point, store_sf2_point, 2, 1);
1085static SENSOR_DEVICE_ATTR_2(sf2_point3_fan1, S_IRUGO | S_IWUSR,
1086                        show_sf2_point, store_sf2_point, 3, 1);
1087static SENSOR_DEVICE_ATTR_2(sf2_point4_fan1, S_IRUGO | S_IWUSR,
1088                        show_sf2_point, store_sf2_point, 4, 1);
1089static SENSOR_DEVICE_ATTR_2(sf2_point1_fan2, S_IRUGO | S_IWUSR,
1090                        show_sf2_point, store_sf2_point, 1, 2);
1091static SENSOR_DEVICE_ATTR_2(sf2_point2_fan2, S_IRUGO | S_IWUSR,
1092                        show_sf2_point, store_sf2_point, 2, 2);
1093static SENSOR_DEVICE_ATTR_2(sf2_point3_fan2, S_IRUGO | S_IWUSR,
1094                        show_sf2_point, store_sf2_point, 3, 2);
1095static SENSOR_DEVICE_ATTR_2(sf2_point4_fan2, S_IRUGO | S_IWUSR,
1096                        show_sf2_point, store_sf2_point, 4, 2);
1097static SENSOR_DEVICE_ATTR_2(sf2_point1_fan3, S_IRUGO | S_IWUSR,
1098                        show_sf2_point, store_sf2_point, 1, 3);
1099static SENSOR_DEVICE_ATTR_2(sf2_point2_fan3, S_IRUGO | S_IWUSR,
1100                        show_sf2_point, store_sf2_point, 2, 3);
1101static SENSOR_DEVICE_ATTR_2(sf2_point3_fan3, S_IRUGO | S_IWUSR,
1102                        show_sf2_point, store_sf2_point, 3, 3);
1103static SENSOR_DEVICE_ATTR_2(sf2_point4_fan3, S_IRUGO | S_IWUSR,
1104                        show_sf2_point, store_sf2_point, 4, 3);
1105static SENSOR_DEVICE_ATTR_2(sf2_level1_fan1, S_IRUGO | S_IWUSR,
1106                        show_sf2_level, store_sf2_level, 1, 1);
1107static SENSOR_DEVICE_ATTR_2(sf2_level2_fan1, S_IRUGO | S_IWUSR,
1108                        show_sf2_level, store_sf2_level, 2, 1);
1109static SENSOR_DEVICE_ATTR_2(sf2_level3_fan1, S_IRUGO | S_IWUSR,
1110                        show_sf2_level, store_sf2_level, 3, 1);
1111static SENSOR_DEVICE_ATTR_2(sf2_level1_fan2, S_IRUGO | S_IWUSR,
1112                        show_sf2_level, store_sf2_level, 1, 2);
1113static SENSOR_DEVICE_ATTR_2(sf2_level2_fan2, S_IRUGO | S_IWUSR,
1114                        show_sf2_level, store_sf2_level, 2, 2);
1115static SENSOR_DEVICE_ATTR_2(sf2_level3_fan2, S_IRUGO | S_IWUSR,
1116                        show_sf2_level, store_sf2_level, 3, 2);
1117static SENSOR_DEVICE_ATTR_2(sf2_level1_fan3, S_IRUGO | S_IWUSR,
1118                        show_sf2_level, store_sf2_level, 1, 3);
1119static SENSOR_DEVICE_ATTR_2(sf2_level2_fan3, S_IRUGO | S_IWUSR,
1120                        show_sf2_level, store_sf2_level, 2, 3);
1121static SENSOR_DEVICE_ATTR_2(sf2_level3_fan3, S_IRUGO | S_IWUSR,
1122                        show_sf2_level, store_sf2_level, 3, 3);
1123static SENSOR_DEVICE_ATTR(fan1_input, S_IRUGO, show_fan, NULL, 1);
1124static SENSOR_DEVICE_ATTR(fan2_input, S_IRUGO, show_fan, NULL, 2);
1125static SENSOR_DEVICE_ATTR(fan3_input, S_IRUGO, show_fan, NULL, 3);
1126static SENSOR_DEVICE_ATTR(fan4_input, S_IRUGO, show_fan, NULL, 4);
1127static SENSOR_DEVICE_ATTR(fan5_input, S_IRUGO, show_fan, NULL, 5);
1128static SENSOR_DEVICE_ATTR(fan6_input, S_IRUGO, show_fan, NULL, 6);
1129static SENSOR_DEVICE_ATTR(fan7_input, S_IRUGO, show_fan, NULL, 7);
1130static SENSOR_DEVICE_ATTR(fan1_min, S_IWUSR | S_IRUGO,
1131                        show_fan_min, store_fan_min, 1);
1132static SENSOR_DEVICE_ATTR(fan2_min, S_IWUSR | S_IRUGO,
1133                        show_fan_min, store_fan_min, 2);
1134static SENSOR_DEVICE_ATTR(fan3_min, S_IWUSR | S_IRUGO,
1135                        show_fan_min, store_fan_min, 3);
1136static SENSOR_DEVICE_ATTR(fan4_min, S_IWUSR | S_IRUGO,
1137                        show_fan_min, store_fan_min, 4);
1138static SENSOR_DEVICE_ATTR(fan5_min, S_IWUSR | S_IRUGO,
1139                        show_fan_min, store_fan_min, 5);
1140static SENSOR_DEVICE_ATTR(fan6_min, S_IWUSR | S_IRUGO,
1141                        show_fan_min, store_fan_min, 6);
1142static SENSOR_DEVICE_ATTR(fan7_min, S_IWUSR | S_IRUGO,
1143                        show_fan_min, store_fan_min, 7);
1144static SENSOR_DEVICE_ATTR(fan1_div, S_IWUSR | S_IRUGO,
1145                        show_fan_div, store_fan_div, 1);
1146static SENSOR_DEVICE_ATTR(fan2_div, S_IWUSR | S_IRUGO,
1147                        show_fan_div, store_fan_div, 2);
1148static SENSOR_DEVICE_ATTR(fan3_div, S_IWUSR | S_IRUGO,
1149                        show_fan_div, store_fan_div, 3);
1150static SENSOR_DEVICE_ATTR(fan4_div, S_IWUSR | S_IRUGO,
1151                        show_fan_div, store_fan_div, 4);
1152static SENSOR_DEVICE_ATTR(fan5_div, S_IWUSR | S_IRUGO,
1153                        show_fan_div, store_fan_div, 5);
1154static SENSOR_DEVICE_ATTR(fan6_div, S_IWUSR | S_IRUGO,
1155                        show_fan_div, store_fan_div, 6);
1156static SENSOR_DEVICE_ATTR(fan7_div, S_IWUSR | S_IRUGO,
1157                        show_fan_div, store_fan_div, 7);
1158
1159static struct attribute *w83792d_attributes_fan[4][7] = {
1160        {
1161                &sensor_dev_attr_fan4_input.dev_attr.attr,
1162                &sensor_dev_attr_fan4_min.dev_attr.attr,
1163                &sensor_dev_attr_fan4_div.dev_attr.attr,
1164                &sensor_dev_attr_fan4_alarm.dev_attr.attr,
1165                &sensor_dev_attr_pwm4.dev_attr.attr,
1166                &sensor_dev_attr_pwm4_mode.dev_attr.attr,
1167                NULL
1168        }, {
1169                &sensor_dev_attr_fan5_input.dev_attr.attr,
1170                &sensor_dev_attr_fan5_min.dev_attr.attr,
1171                &sensor_dev_attr_fan5_div.dev_attr.attr,
1172                &sensor_dev_attr_fan5_alarm.dev_attr.attr,
1173                &sensor_dev_attr_pwm5.dev_attr.attr,
1174                &sensor_dev_attr_pwm5_mode.dev_attr.attr,
1175                NULL
1176        }, {
1177                &sensor_dev_attr_fan6_input.dev_attr.attr,
1178                &sensor_dev_attr_fan6_min.dev_attr.attr,
1179                &sensor_dev_attr_fan6_div.dev_attr.attr,
1180                &sensor_dev_attr_fan6_alarm.dev_attr.attr,
1181                &sensor_dev_attr_pwm6.dev_attr.attr,
1182                &sensor_dev_attr_pwm6_mode.dev_attr.attr,
1183                NULL
1184        }, {
1185                &sensor_dev_attr_fan7_input.dev_attr.attr,
1186                &sensor_dev_attr_fan7_min.dev_attr.attr,
1187                &sensor_dev_attr_fan7_div.dev_attr.attr,
1188                &sensor_dev_attr_fan7_alarm.dev_attr.attr,
1189                &sensor_dev_attr_pwm7.dev_attr.attr,
1190                &sensor_dev_attr_pwm7_mode.dev_attr.attr,
1191                NULL
1192        }
1193};
1194
1195static const struct attribute_group w83792d_group_fan[4] = {
1196        { .attrs = w83792d_attributes_fan[0] },
1197        { .attrs = w83792d_attributes_fan[1] },
1198        { .attrs = w83792d_attributes_fan[2] },
1199        { .attrs = w83792d_attributes_fan[3] },
1200};
1201
1202static struct attribute *w83792d_attributes[] = {
1203        &sensor_dev_attr_in0_input.dev_attr.attr,
1204        &sensor_dev_attr_in0_max.dev_attr.attr,
1205        &sensor_dev_attr_in0_min.dev_attr.attr,
1206        &sensor_dev_attr_in1_input.dev_attr.attr,
1207        &sensor_dev_attr_in1_max.dev_attr.attr,
1208        &sensor_dev_attr_in1_min.dev_attr.attr,
1209        &sensor_dev_attr_in2_input.dev_attr.attr,
1210        &sensor_dev_attr_in2_max.dev_attr.attr,
1211        &sensor_dev_attr_in2_min.dev_attr.attr,
1212        &sensor_dev_attr_in3_input.dev_attr.attr,
1213        &sensor_dev_attr_in3_max.dev_attr.attr,
1214        &sensor_dev_attr_in3_min.dev_attr.attr,
1215        &sensor_dev_attr_in4_input.dev_attr.attr,
1216        &sensor_dev_attr_in4_max.dev_attr.attr,
1217        &sensor_dev_attr_in4_min.dev_attr.attr,
1218        &sensor_dev_attr_in5_input.dev_attr.attr,
1219        &sensor_dev_attr_in5_max.dev_attr.attr,
1220        &sensor_dev_attr_in5_min.dev_attr.attr,
1221        &sensor_dev_attr_in6_input.dev_attr.attr,
1222        &sensor_dev_attr_in6_max.dev_attr.attr,
1223        &sensor_dev_attr_in6_min.dev_attr.attr,
1224        &sensor_dev_attr_in7_input.dev_attr.attr,
1225        &sensor_dev_attr_in7_max.dev_attr.attr,
1226        &sensor_dev_attr_in7_min.dev_attr.attr,
1227        &sensor_dev_attr_in8_input.dev_attr.attr,
1228        &sensor_dev_attr_in8_max.dev_attr.attr,
1229        &sensor_dev_attr_in8_min.dev_attr.attr,
1230        &sensor_dev_attr_in0_alarm.dev_attr.attr,
1231        &sensor_dev_attr_in1_alarm.dev_attr.attr,
1232        &sensor_dev_attr_in2_alarm.dev_attr.attr,
1233        &sensor_dev_attr_in3_alarm.dev_attr.attr,
1234        &sensor_dev_attr_in4_alarm.dev_attr.attr,
1235        &sensor_dev_attr_in5_alarm.dev_attr.attr,
1236        &sensor_dev_attr_in6_alarm.dev_attr.attr,
1237        &sensor_dev_attr_in7_alarm.dev_attr.attr,
1238        &sensor_dev_attr_in8_alarm.dev_attr.attr,
1239        &sensor_dev_attr_temp1_input.dev_attr.attr,
1240        &sensor_dev_attr_temp1_max.dev_attr.attr,
1241        &sensor_dev_attr_temp1_max_hyst.dev_attr.attr,
1242        &sensor_dev_attr_temp2_input.dev_attr.attr,
1243        &sensor_dev_attr_temp2_max.dev_attr.attr,
1244        &sensor_dev_attr_temp2_max_hyst.dev_attr.attr,
1245        &sensor_dev_attr_temp3_input.dev_attr.attr,
1246        &sensor_dev_attr_temp3_max.dev_attr.attr,
1247        &sensor_dev_attr_temp3_max_hyst.dev_attr.attr,
1248        &sensor_dev_attr_temp1_alarm.dev_attr.attr,
1249        &sensor_dev_attr_temp2_alarm.dev_attr.attr,
1250        &sensor_dev_attr_temp3_alarm.dev_attr.attr,
1251        &sensor_dev_attr_pwm1.dev_attr.attr,
1252        &sensor_dev_attr_pwm1_mode.dev_attr.attr,
1253        &sensor_dev_attr_pwm1_enable.dev_attr.attr,
1254        &sensor_dev_attr_pwm2.dev_attr.attr,
1255        &sensor_dev_attr_pwm2_mode.dev_attr.attr,
1256        &sensor_dev_attr_pwm2_enable.dev_attr.attr,
1257        &sensor_dev_attr_pwm3.dev_attr.attr,
1258        &sensor_dev_attr_pwm3_mode.dev_attr.attr,
1259        &sensor_dev_attr_pwm3_enable.dev_attr.attr,
1260        &dev_attr_alarms.attr,
1261        &dev_attr_intrusion0_alarm.attr,
1262        &sensor_dev_attr_tolerance1.dev_attr.attr,
1263        &sensor_dev_attr_thermal_cruise1.dev_attr.attr,
1264        &sensor_dev_attr_tolerance2.dev_attr.attr,
1265        &sensor_dev_attr_thermal_cruise2.dev_attr.attr,
1266        &sensor_dev_attr_tolerance3.dev_attr.attr,
1267        &sensor_dev_attr_thermal_cruise3.dev_attr.attr,
1268        &sensor_dev_attr_sf2_point1_fan1.dev_attr.attr,
1269        &sensor_dev_attr_sf2_point2_fan1.dev_attr.attr,
1270        &sensor_dev_attr_sf2_point3_fan1.dev_attr.attr,
1271        &sensor_dev_attr_sf2_point4_fan1.dev_attr.attr,
1272        &sensor_dev_attr_sf2_point1_fan2.dev_attr.attr,
1273        &sensor_dev_attr_sf2_point2_fan2.dev_attr.attr,
1274        &sensor_dev_attr_sf2_point3_fan2.dev_attr.attr,
1275        &sensor_dev_attr_sf2_point4_fan2.dev_attr.attr,
1276        &sensor_dev_attr_sf2_point1_fan3.dev_attr.attr,
1277        &sensor_dev_attr_sf2_point2_fan3.dev_attr.attr,
1278        &sensor_dev_attr_sf2_point3_fan3.dev_attr.attr,
1279        &sensor_dev_attr_sf2_point4_fan3.dev_attr.attr,
1280        &sensor_dev_attr_sf2_level1_fan1.dev_attr.attr,
1281        &sensor_dev_attr_sf2_level2_fan1.dev_attr.attr,
1282        &sensor_dev_attr_sf2_level3_fan1.dev_attr.attr,
1283        &sensor_dev_attr_sf2_level1_fan2.dev_attr.attr,
1284        &sensor_dev_attr_sf2_level2_fan2.dev_attr.attr,
1285        &sensor_dev_attr_sf2_level3_fan2.dev_attr.attr,
1286        &sensor_dev_attr_sf2_level1_fan3.dev_attr.attr,
1287        &sensor_dev_attr_sf2_level2_fan3.dev_attr.attr,
1288        &sensor_dev_attr_sf2_level3_fan3.dev_attr.attr,
1289        &sensor_dev_attr_fan1_input.dev_attr.attr,
1290        &sensor_dev_attr_fan1_min.dev_attr.attr,
1291        &sensor_dev_attr_fan1_div.dev_attr.attr,
1292        &sensor_dev_attr_fan1_alarm.dev_attr.attr,
1293        &sensor_dev_attr_fan2_input.dev_attr.attr,
1294        &sensor_dev_attr_fan2_min.dev_attr.attr,
1295        &sensor_dev_attr_fan2_div.dev_attr.attr,
1296        &sensor_dev_attr_fan2_alarm.dev_attr.attr,
1297        &sensor_dev_attr_fan3_input.dev_attr.attr,
1298        &sensor_dev_attr_fan3_min.dev_attr.attr,
1299        &sensor_dev_attr_fan3_div.dev_attr.attr,
1300        &sensor_dev_attr_fan3_alarm.dev_attr.attr,
1301        NULL
1302};
1303
1304static const struct attribute_group w83792d_group = {
1305        .attrs = w83792d_attributes,
1306};
1307
1308/* Return 0 if detection is successful, -ENODEV otherwise */
1309static int
1310w83792d_detect(struct i2c_client *client, struct i2c_board_info *info)
1311{
1312        struct i2c_adapter *adapter = client->adapter;
1313        int val1, val2;
1314        unsigned short address = client->addr;
1315
1316        if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
1317                return -ENODEV;
1318
1319        if (w83792d_read_value(client, W83792D_REG_CONFIG) & 0x80)
1320                return -ENODEV;
1321
1322        val1 = w83792d_read_value(client, W83792D_REG_BANK);
1323        val2 = w83792d_read_value(client, W83792D_REG_CHIPMAN);
1324        /* Check for Winbond ID if in bank 0 */
1325        if (!(val1 & 0x07)) {  /* is Bank0 */
1326                if ((!(val1 & 0x80) && val2 != 0xa3) ||
1327                    ((val1 & 0x80) && val2 != 0x5c))
1328                        return -ENODEV;
1329        }
1330        /*
1331         * If Winbond chip, address of chip and W83792D_REG_I2C_ADDR
1332         * should match
1333         */
1334        if (w83792d_read_value(client, W83792D_REG_I2C_ADDR) != address)
1335                return -ENODEV;
1336
1337        /*  Put it now into bank 0 and Vendor ID High Byte */
1338        w83792d_write_value(client,
1339                            W83792D_REG_BANK,
1340                            (w83792d_read_value(client,
1341                                W83792D_REG_BANK) & 0x78) | 0x80);
1342
1343        /* Determine the chip type. */
1344        val1 = w83792d_read_value(client, W83792D_REG_WCHIPID);
1345        val2 = w83792d_read_value(client, W83792D_REG_CHIPMAN);
1346        if (val1 != 0x7a || val2 != 0x5c)
1347                return -ENODEV;
1348
1349        strlcpy(info->type, "w83792d", I2C_NAME_SIZE);
1350
1351        return 0;
1352}
1353
1354static int
1355w83792d_probe(struct i2c_client *client)
1356{
1357        struct w83792d_data *data;
1358        struct device *dev = &client->dev;
1359        int i, val1, err;
1360
1361        data = devm_kzalloc(dev, sizeof(struct w83792d_data), GFP_KERNEL);
1362        if (!data)
1363                return -ENOMEM;
1364
1365        i2c_set_clientdata(client, data);
1366        mutex_init(&data->update_lock);
1367
1368        err = w83792d_detect_subclients(client);
1369        if (err)
1370                return err;
1371
1372        /* Initialize the chip */
1373        w83792d_init_client(client);
1374
1375        /* A few vars need to be filled upon startup */
1376        for (i = 0; i < 7; i++) {
1377                data->fan_min[i] = w83792d_read_value(client,
1378                                        W83792D_REG_FAN_MIN[i]);
1379        }
1380
1381        /* Register sysfs hooks */
1382        err = sysfs_create_group(&dev->kobj, &w83792d_group);
1383        if (err)
1384                return err;
1385
1386        /*
1387         * Read GPIO enable register to check if pins for fan 4,5 are used as
1388         * GPIO
1389         */
1390        val1 = w83792d_read_value(client, W83792D_REG_GPIO_EN);
1391
1392        if (!(val1 & 0x40)) {
1393                err = sysfs_create_group(&dev->kobj, &w83792d_group_fan[0]);
1394                if (err)
1395                        goto exit_remove_files;
1396        }
1397
1398        if (!(val1 & 0x20)) {
1399                err = sysfs_create_group(&dev->kobj, &w83792d_group_fan[1]);
1400                if (err)
1401                        goto exit_remove_files;
1402        }
1403
1404        val1 = w83792d_read_value(client, W83792D_REG_PIN);
1405        if (val1 & 0x40) {
1406                err = sysfs_create_group(&dev->kobj, &w83792d_group_fan[2]);
1407                if (err)
1408                        goto exit_remove_files;
1409        }
1410
1411        if (val1 & 0x04) {
1412                err = sysfs_create_group(&dev->kobj, &w83792d_group_fan[3]);
1413                if (err)
1414                        goto exit_remove_files;
1415        }
1416
1417        data->hwmon_dev = hwmon_device_register(dev);
1418        if (IS_ERR(data->hwmon_dev)) {
1419                err = PTR_ERR(data->hwmon_dev);
1420                goto exit_remove_files;
1421        }
1422
1423        return 0;
1424
1425exit_remove_files:
1426        sysfs_remove_group(&dev->kobj, &w83792d_group);
1427        for (i = 0; i < ARRAY_SIZE(w83792d_group_fan); i++)
1428                sysfs_remove_group(&dev->kobj, &w83792d_group_fan[i]);
1429        return err;
1430}
1431
1432static int
1433w83792d_remove(struct i2c_client *client)
1434{
1435        struct w83792d_data *data = i2c_get_clientdata(client);
1436        int i;
1437
1438        hwmon_device_unregister(data->hwmon_dev);
1439        sysfs_remove_group(&client->dev.kobj, &w83792d_group);
1440        for (i = 0; i < ARRAY_SIZE(w83792d_group_fan); i++)
1441                sysfs_remove_group(&client->dev.kobj,
1442                                   &w83792d_group_fan[i]);
1443
1444        return 0;
1445}
1446
1447static void
1448w83792d_init_client(struct i2c_client *client)
1449{
1450        u8 temp2_cfg, temp3_cfg, vid_in_b;
1451
1452        if (init)
1453                w83792d_write_value(client, W83792D_REG_CONFIG, 0x80);
1454
1455        /*
1456         * Clear the bit6 of W83792D_REG_VID_IN_B(set it into 0):
1457         * W83792D_REG_VID_IN_B bit6 = 0: the high/low limit of
1458         * vin0/vin1 can be modified by user;
1459         * W83792D_REG_VID_IN_B bit6 = 1: the high/low limit of
1460         * vin0/vin1 auto-updated, can NOT be modified by user.
1461         */
1462        vid_in_b = w83792d_read_value(client, W83792D_REG_VID_IN_B);
1463        w83792d_write_value(client, W83792D_REG_VID_IN_B,
1464                            vid_in_b & 0xbf);
1465
1466        temp2_cfg = w83792d_read_value(client, W83792D_REG_TEMP2_CONFIG);
1467        temp3_cfg = w83792d_read_value(client, W83792D_REG_TEMP3_CONFIG);
1468        w83792d_write_value(client, W83792D_REG_TEMP2_CONFIG,
1469                                temp2_cfg & 0xe6);
1470        w83792d_write_value(client, W83792D_REG_TEMP3_CONFIG,
1471                                temp3_cfg & 0xe6);
1472
1473        /* Start monitoring */
1474        w83792d_write_value(client, W83792D_REG_CONFIG,
1475                            (w83792d_read_value(client,
1476                                                W83792D_REG_CONFIG) & 0xf7)
1477                            | 0x01);
1478}
1479
1480static struct w83792d_data *w83792d_update_device(struct device *dev)
1481{
1482        struct i2c_client *client = to_i2c_client(dev);
1483        struct w83792d_data *data = i2c_get_clientdata(client);
1484        int i, j;
1485        u8 reg_array_tmp[4], reg_tmp;
1486
1487        mutex_lock(&data->update_lock);
1488
1489        if (time_after
1490            (jiffies - data->last_updated, (unsigned long) (HZ * 3))
1491            || time_before(jiffies, data->last_updated) || !data->valid) {
1492                dev_dbg(dev, "Starting device update\n");
1493
1494                /* Update the voltages measured value and limits */
1495                for (i = 0; i < 9; i++) {
1496                        data->in[i] = w83792d_read_value(client,
1497                                                W83792D_REG_IN[i]);
1498                        data->in_max[i] = w83792d_read_value(client,
1499                                                W83792D_REG_IN_MAX[i]);
1500                        data->in_min[i] = w83792d_read_value(client,
1501                                                W83792D_REG_IN_MIN[i]);
1502                }
1503                data->low_bits = w83792d_read_value(client,
1504                                                W83792D_REG_LOW_BITS1) +
1505                                 (w83792d_read_value(client,
1506                                                W83792D_REG_LOW_BITS2) << 8);
1507                for (i = 0; i < 7; i++) {
1508                        /* Update the Fan measured value and limits */
1509                        data->fan[i] = w83792d_read_value(client,
1510                                                W83792D_REG_FAN[i]);
1511                        data->fan_min[i] = w83792d_read_value(client,
1512                                                W83792D_REG_FAN_MIN[i]);
1513                        /* Update the PWM/DC Value and PWM/DC flag */
1514                        data->pwm[i] = w83792d_read_value(client,
1515                                                W83792D_REG_PWM[i]);
1516                }
1517
1518                reg_tmp = w83792d_read_value(client, W83792D_REG_FAN_CFG);
1519                data->pwmenable[0] = reg_tmp & 0x03;
1520                data->pwmenable[1] = (reg_tmp>>2) & 0x03;
1521                data->pwmenable[2] = (reg_tmp>>4) & 0x03;
1522
1523                for (i = 0; i < 3; i++) {
1524                        data->temp1[i] = w83792d_read_value(client,
1525                                                        W83792D_REG_TEMP1[i]);
1526                }
1527                for (i = 0; i < 2; i++) {
1528                        for (j = 0; j < 6; j++) {
1529                                data->temp_add[i][j] = w83792d_read_value(
1530                                        client, W83792D_REG_TEMP_ADD[i][j]);
1531                        }
1532                }
1533
1534                /* Update the Fan Divisor */
1535                for (i = 0; i < 4; i++) {
1536                        reg_array_tmp[i] = w83792d_read_value(client,
1537                                                        W83792D_REG_FAN_DIV[i]);
1538                }
1539                data->fan_div[0] = reg_array_tmp[0] & 0x07;
1540                data->fan_div[1] = (reg_array_tmp[0] >> 4) & 0x07;
1541                data->fan_div[2] = reg_array_tmp[1] & 0x07;
1542                data->fan_div[3] = (reg_array_tmp[1] >> 4) & 0x07;
1543                data->fan_div[4] = reg_array_tmp[2] & 0x07;
1544                data->fan_div[5] = (reg_array_tmp[2] >> 4) & 0x07;
1545                data->fan_div[6] = reg_array_tmp[3] & 0x07;
1546
1547                /* Update the realtime status */
1548                data->alarms = w83792d_read_value(client, W83792D_REG_ALARM1) +
1549                        (w83792d_read_value(client, W83792D_REG_ALARM2) << 8) +
1550                        (w83792d_read_value(client, W83792D_REG_ALARM3) << 16);
1551
1552                /* Update CaseOpen status and it's CLR_CHS. */
1553                data->chassis = (w83792d_read_value(client,
1554                        W83792D_REG_CHASSIS) >> 5) & 0x01;
1555
1556                /* Update Thermal Cruise/Smart Fan I target value */
1557                for (i = 0; i < 3; i++) {
1558                        data->thermal_cruise[i] =
1559                                w83792d_read_value(client,
1560                                W83792D_REG_THERMAL[i]) & 0x7f;
1561                }
1562
1563                /* Update Smart Fan I/II tolerance */
1564                reg_tmp = w83792d_read_value(client, W83792D_REG_TOLERANCE[0]);
1565                data->tolerance[0] = reg_tmp & 0x0f;
1566                data->tolerance[1] = (reg_tmp >> 4) & 0x0f;
1567                data->tolerance[2] = w83792d_read_value(client,
1568                                        W83792D_REG_TOLERANCE[2]) & 0x0f;
1569
1570                /* Update Smart Fan II temperature points */
1571                for (i = 0; i < 3; i++) {
1572                        for (j = 0; j < 4; j++) {
1573                                data->sf2_points[i][j]
1574                                  = w83792d_read_value(client,
1575                                        W83792D_REG_POINTS[i][j]) & 0x7f;
1576                        }
1577                }
1578
1579                /* Update Smart Fan II duty cycle levels */
1580                for (i = 0; i < 3; i++) {
1581                        reg_tmp = w83792d_read_value(client,
1582                                                W83792D_REG_LEVELS[i][0]);
1583                        data->sf2_levels[i][0] = reg_tmp & 0x0f;
1584                        data->sf2_levels[i][1] = (reg_tmp >> 4) & 0x0f;
1585                        reg_tmp = w83792d_read_value(client,
1586                                                W83792D_REG_LEVELS[i][2]);
1587                        data->sf2_levels[i][2] = (reg_tmp >> 4) & 0x0f;
1588                        data->sf2_levels[i][3] = reg_tmp & 0x0f;
1589                }
1590
1591                data->last_updated = jiffies;
1592                data->valid = 1;
1593        }
1594
1595        mutex_unlock(&data->update_lock);
1596
1597#ifdef DEBUG
1598        w83792d_print_debug(data, dev);
1599#endif
1600
1601        return data;
1602}
1603
1604#ifdef DEBUG
1605static void w83792d_print_debug(struct w83792d_data *data, struct device *dev)
1606{
1607        int i = 0, j = 0;
1608        dev_dbg(dev, "==========The following is the debug message...========\n");
1609        dev_dbg(dev, "9 set of Voltages: =====>\n");
1610        for (i = 0; i < 9; i++) {
1611                dev_dbg(dev, "vin[%d] is: 0x%x\n", i, data->in[i]);
1612                dev_dbg(dev, "vin[%d] max is: 0x%x\n", i, data->in_max[i]);
1613                dev_dbg(dev, "vin[%d] min is: 0x%x\n", i, data->in_min[i]);
1614        }
1615        dev_dbg(dev, "Low Bit1 is: 0x%x\n", data->low_bits & 0xff);
1616        dev_dbg(dev, "Low Bit2 is: 0x%x\n", data->low_bits >> 8);
1617        dev_dbg(dev, "7 set of Fan Counts and Duty Cycles: =====>\n");
1618        for (i = 0; i < 7; i++) {
1619                dev_dbg(dev, "fan[%d] is: 0x%x\n", i, data->fan[i]);
1620                dev_dbg(dev, "fan[%d] min is: 0x%x\n", i, data->fan_min[i]);
1621                dev_dbg(dev, "pwm[%d]     is: 0x%x\n", i, data->pwm[i]);
1622        }
1623        dev_dbg(dev, "3 set of Temperatures: =====>\n");
1624        for (i = 0; i < 3; i++)
1625                dev_dbg(dev, "temp1[%d] is: 0x%x\n", i, data->temp1[i]);
1626
1627        for (i = 0; i < 2; i++) {
1628                for (j = 0; j < 6; j++) {
1629                        dev_dbg(dev, "temp_add[%d][%d] is: 0x%x\n", i, j,
1630                                                        data->temp_add[i][j]);
1631                }
1632        }
1633
1634        for (i = 0; i < 7; i++)
1635                dev_dbg(dev, "fan_div[%d] is: 0x%x\n", i, data->fan_div[i]);
1636
1637        dev_dbg(dev, "==========End of the debug message...================\n");
1638        dev_dbg(dev, "\n");
1639}
1640#endif
1641
1642module_i2c_driver(w83792d_driver);
1643
1644MODULE_AUTHOR("Shane Huang (Winbond)");
1645MODULE_DESCRIPTION("W83792AD/D driver for linux-2.6");
1646MODULE_LICENSE("GPL");
1647