// SPDX-License-Identifier: GPL-2.0-only
/*
 * PHY support for Xenon SDHC
 *
 * Copyright (C) 2016 Marvell, All Rights Reserved.
 *
 * Author:      Hu Ziji <huziji@marvell.com>
 * Date:        2016-8-24
 */

#include <linux/slab.h>
#include <linux/delay.h>
#include <linux/ktime.h>
#include <linux/of_address.h>

#include "sdhci-pltfm.h"
#include "sdhci-xenon.h"

/* Register base for eMMC PHY 5.0 Version */
#define XENON_EMMC_5_0_PHY_REG_BASE             0x0160
/* Register base for eMMC PHY 5.1 Version */
#define XENON_EMMC_PHY_REG_BASE                 0x0170

#define XENON_EMMC_PHY_TIMING_ADJUST            XENON_EMMC_PHY_REG_BASE
#define XENON_EMMC_5_0_PHY_TIMING_ADJUST        XENON_EMMC_5_0_PHY_REG_BASE
#define XENON_TIMING_ADJUST_SLOW_MODE           BIT(29)
#define XENON_TIMING_ADJUST_SDIO_MODE           BIT(28)
#define XENON_SAMPL_INV_QSP_PHASE_SELECT        BIT(18)
#define XENON_SAMPL_INV_QSP_PHASE_SELECT_SHIFT  18
#define XENON_PHY_INITIALIZAION                 BIT(31)
#define XENON_WAIT_CYCLE_BEFORE_USING_MASK      0xF
#define XENON_WAIT_CYCLE_BEFORE_USING_SHIFT     12
#define XENON_FC_SYNC_EN_DURATION_MASK          0xF
#define XENON_FC_SYNC_EN_DURATION_SHIFT         8
#define XENON_FC_SYNC_RST_EN_DURATION_MASK      0xF
#define XENON_FC_SYNC_RST_EN_DURATION_SHIFT     4
#define XENON_FC_SYNC_RST_DURATION_MASK         0xF
#define XENON_FC_SYNC_RST_DURATION_SHIFT        0

#define XENON_EMMC_PHY_FUNC_CONTROL             (XENON_EMMC_PHY_REG_BASE + 0x4)
#define XENON_EMMC_5_0_PHY_FUNC_CONTROL         \
        (XENON_EMMC_5_0_PHY_REG_BASE + 0x4)
#define XENON_ASYNC_DDRMODE_MASK                BIT(23)
#define XENON_ASYNC_DDRMODE_SHIFT               23
#define XENON_CMD_DDR_MODE                      BIT(16)
#define XENON_DQ_DDR_MODE_SHIFT                 8
#define XENON_DQ_DDR_MODE_MASK                  0xFF
#define XENON_DQ_ASYNC_MODE                     BIT(4)

#define XENON_EMMC_PHY_PAD_CONTROL              (XENON_EMMC_PHY_REG_BASE + 0x8)
#define XENON_EMMC_5_0_PHY_PAD_CONTROL          \
        (XENON_EMMC_5_0_PHY_REG_BASE + 0x8)
#define XENON_REC_EN_SHIFT                      24
#define XENON_REC_EN_MASK                       0xF
#define XENON_FC_DQ_RECEN                       BIT(24)
#define XENON_FC_CMD_RECEN                      BIT(25)
#define XENON_FC_QSP_RECEN                      BIT(26)
#define XENON_FC_QSN_RECEN                      BIT(27)
#define XENON_OEN_QSN                           BIT(28)
#define XENON_AUTO_RECEN_CTRL                   BIT(30)
#define XENON_FC_ALL_CMOS_RECEIVER              0xF000

#define XENON_EMMC5_FC_QSP_PD                   BIT(18)
#define XENON_EMMC5_FC_QSP_PU                   BIT(22)
#define XENON_EMMC5_FC_CMD_PD                   BIT(17)
#define XENON_EMMC5_FC_CMD_PU                   BIT(21)
#define XENON_EMMC5_FC_DQ_PD                    BIT(16)
#define XENON_EMMC5_FC_DQ_PU                    BIT(20)

#define XENON_EMMC_PHY_PAD_CONTROL1             (XENON_EMMC_PHY_REG_BASE + 0xC)
#define XENON_EMMC5_1_FC_QSP_PD                 BIT(9)
#define XENON_EMMC5_1_FC_QSP_PU                 BIT(25)
#define XENON_EMMC5_1_FC_CMD_PD                 BIT(8)
#define XENON_EMMC5_1_FC_CMD_PU                 BIT(24)
#define XENON_EMMC5_1_FC_DQ_PD                  0xFF
#define XENON_EMMC5_1_FC_DQ_PU                  (0xFF << 16)

#define XENON_EMMC_PHY_PAD_CONTROL2             (XENON_EMMC_PHY_REG_BASE + 0x10)
#define XENON_EMMC_5_0_PHY_PAD_CONTROL2         \
        (XENON_EMMC_5_0_PHY_REG_BASE + 0xC)
#define XENON_ZNR_MASK                          0x1F
#define XENON_ZNR_SHIFT                         8
#define XENON_ZPR_MASK                          0x1F
/* Preferred ZNR and ZPR value vary between different boards.
 * The specific ZNR and ZPR value should be defined here
 * according to board actual timing.
 */
#define XENON_ZNR_DEF_VALUE                     0xF
#define XENON_ZPR_DEF_VALUE                     0xF

#define XENON_EMMC_PHY_DLL_CONTROL              (XENON_EMMC_PHY_REG_BASE + 0x14)
#define XENON_EMMC_5_0_PHY_DLL_CONTROL          \
        (XENON_EMMC_5_0_PHY_REG_BASE + 0x10)
#define XENON_DLL_ENABLE                        BIT(31)
#define XENON_DLL_UPDATE_STROBE_5_0             BIT(30)
#define XENON_DLL_REFCLK_SEL                    BIT(30)
#define XENON_DLL_UPDATE                        BIT(23)
#define XENON_DLL_PHSEL1_SHIFT                  24
#define XENON_DLL_PHSEL0_SHIFT                  16
#define XENON_DLL_PHASE_MASK                    0x3F
#define XENON_DLL_PHASE_90_DEGREE               0x1F
#define XENON_DLL_FAST_LOCK                     BIT(5)
#define XENON_DLL_GAIN2X                        BIT(3)
#define XENON_DLL_BYPASS_EN                     BIT(0)

#define XENON_EMMC_5_0_PHY_LOGIC_TIMING_ADJUST  \
        (XENON_EMMC_5_0_PHY_REG_BASE + 0x14)
#define XENON_EMMC_5_0_PHY_LOGIC_TIMING_VALUE   0x5A54
#define XENON_EMMC_PHY_LOGIC_TIMING_ADJUST      (XENON_EMMC_PHY_REG_BASE + 0x18)
#define XENON_LOGIC_TIMING_VALUE                0x00AA8977

/*
 * List offset of PHY registers and some special register values
 * in eMMC PHY 5.0 or eMMC PHY 5.1
 */
struct xenon_emmc_phy_regs {
        /* Offset of Timing Adjust register */
        u16 timing_adj;
        /* Offset of Func Control register */
        u16 func_ctrl;
        /* Offset of Pad Control register */
        u16 pad_ctrl;
        /* Offset of Pad Control register 2 */
        u16 pad_ctrl2;
        /* Offset of DLL Control register */
        u16 dll_ctrl;
        /* Offset of Logic Timing Adjust register */
        u16 logic_timing_adj;
        /* DLL Update Enable bit */
        u32 dll_update;
        /* value in Logic Timing Adjustment register */
        u32 logic_timing_val;
};

static const char * const phy_types[] = {
        "emmc 5.0 phy",
        "emmc 5.1 phy"
};

enum xenon_phy_type_enum {
        EMMC_5_0_PHY,
        EMMC_5_1_PHY,
        NR_PHY_TYPES
};

enum soc_pad_ctrl_type {
        SOC_PAD_SD,
        SOC_PAD_FIXED_1_8V,
};

struct soc_pad_ctrl {
        /* Register address of SoC PHY PAD ctrl */
        void __iomem    *reg;
        /* SoC PHY PAD ctrl type */
        enum soc_pad_ctrl_type pad_type;
        /* SoC specific operation to set SoC PHY PAD */
        void (*set_soc_pad)(struct sdhci_host *host,
                            unsigned char signal_voltage);
};

static struct xenon_emmc_phy_regs xenon_emmc_5_0_phy_regs = {
        .timing_adj     = XENON_EMMC_5_0_PHY_TIMING_ADJUST,
        .func_ctrl      = XENON_EMMC_5_0_PHY_FUNC_CONTROL,
        .pad_ctrl       = XENON_EMMC_5_0_PHY_PAD_CONTROL,
        .pad_ctrl2      = XENON_EMMC_5_0_PHY_PAD_CONTROL2,
        .dll_ctrl       = XENON_EMMC_5_0_PHY_DLL_CONTROL,
        .logic_timing_adj = XENON_EMMC_5_0_PHY_LOGIC_TIMING_ADJUST,
        .dll_update     = XENON_DLL_UPDATE_STROBE_5_0,
        .logic_timing_val = XENON_EMMC_5_0_PHY_LOGIC_TIMING_VALUE,
};

static struct xenon_emmc_phy_regs xenon_emmc_5_1_phy_regs = {
        .timing_adj     = XENON_EMMC_PHY_TIMING_ADJUST,
        .func_ctrl      = XENON_EMMC_PHY_FUNC_CONTROL,
        .pad_ctrl       = XENON_EMMC_PHY_PAD_CONTROL,
        .pad_ctrl2      = XENON_EMMC_PHY_PAD_CONTROL2,
        .dll_ctrl       = XENON_EMMC_PHY_DLL_CONTROL,
        .logic_timing_adj = XENON_EMMC_PHY_LOGIC_TIMING_ADJUST,
        .dll_update     = XENON_DLL_UPDATE,
        .logic_timing_val = XENON_LOGIC_TIMING_VALUE,
};

/*
 * eMMC PHY configuration and operations
 */
struct xenon_emmc_phy_params {
        bool    slow_mode;

        u8      znr;
        u8      zpr;

        /* Nr of consecutive Sampling Points of a Valid Sampling Window */
        u8      nr_tun_times;
        /* Divider for calculating Tuning Step */
        u8      tun_step_divider;

        struct soc_pad_ctrl pad_ctrl;
};

static int xenon_alloc_emmc_phy(struct sdhci_host *host)
{
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
        struct xenon_emmc_phy_params *params;

        params = devm_kzalloc(mmc_dev(host->mmc), sizeof(*params), GFP_KERNEL);
        if (!params)
                return -ENOMEM;

        priv->phy_params = params;
        if (priv->phy_type == EMMC_5_0_PHY)
                priv->emmc_phy_regs = &xenon_emmc_5_0_phy_regs;
        else
                priv->emmc_phy_regs = &xenon_emmc_5_1_phy_regs;

        return 0;
}

/*
 * eMMC 5.0/5.1 PHY init/re-init.
 * eMMC PHY init should be executed after:
 * 1. SDCLK frequency changes.
 * 2. SDCLK is stopped and re-enabled.
 * 3. config in emmc_phy_regs->timing_adj and emmc_phy_regs->func_ctrl
 * are changed
 */
static int xenon_emmc_phy_init(struct sdhci_host *host)
{
        u32 reg;
        u32 wait, clock;
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
        struct xenon_emmc_phy_regs *phy_regs = priv->emmc_phy_regs;

        reg = sdhci_readl(host, phy_regs->timing_adj);
        reg |= XENON_PHY_INITIALIZAION;
        sdhci_writel(host, reg, phy_regs->timing_adj);

        /* Add duration of FC_SYNC_RST */
        wait = ((reg >> XENON_FC_SYNC_RST_DURATION_SHIFT) &
                        XENON_FC_SYNC_RST_DURATION_MASK);
        /* Add interval between FC_SYNC_EN and FC_SYNC_RST */
        wait += ((reg >> XENON_FC_SYNC_RST_EN_DURATION_SHIFT) &
                        XENON_FC_SYNC_RST_EN_DURATION_MASK);
        /* Add duration of asserting FC_SYNC_EN */
        wait += ((reg >> XENON_FC_SYNC_EN_DURATION_SHIFT) &
                        XENON_FC_SYNC_EN_DURATION_MASK);
        /* Add duration of waiting for PHY */
        wait += ((reg >> XENON_WAIT_CYCLE_BEFORE_USING_SHIFT) &
                        XENON_WAIT_CYCLE_BEFORE_USING_MASK);
        /* 4 additional bus clock and 4 AXI bus clock are required */
        wait += 8;
        wait <<= 20;

        clock = host->clock;
        if (!clock)
                /* Use the possibly slowest bus frequency value */
                clock = XENON_LOWEST_SDCLK_FREQ;
        /* get the wait time */
        wait /= clock;
        wait++;
        /* wait for host eMMC PHY init completes */
        udelay(wait);

        reg = sdhci_readl(host, phy_regs->timing_adj);
        reg &= XENON_PHY_INITIALIZAION;
        if (reg) {
                dev_err(mmc_dev(host->mmc), "eMMC PHY init cannot complete after %d us\n",
                        wait);
                return -ETIMEDOUT;
        }

        return 0;
}

#define ARMADA_3700_SOC_PAD_1_8V        0x1
#define ARMADA_3700_SOC_PAD_3_3V        0x0

static void armada_3700_soc_pad_voltage_set(struct sdhci_host *host,
                                            unsigned char signal_voltage)
{
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
        struct xenon_emmc_phy_params *params = priv->phy_params;

        if (params->pad_ctrl.pad_type == SOC_PAD_FIXED_1_8V) {
                writel(ARMADA_3700_SOC_PAD_1_8V, params->pad_ctrl.reg);
        } else if (params->pad_ctrl.pad_type == SOC_PAD_SD) {
                if (signal_voltage == MMC_SIGNAL_VOLTAGE_180)
                        writel(ARMADA_3700_SOC_PAD_1_8V, params->pad_ctrl.reg);
                else if (signal_voltage == MMC_SIGNAL_VOLTAGE_330)
                        writel(ARMADA_3700_SOC_PAD_3_3V, params->pad_ctrl.reg);
        }
}

/*
 * Set SoC PHY voltage PAD control register,
 * according to the operation voltage on PAD.
 * The detailed operation depends on SoC implementation.
 */
static void xenon_emmc_phy_set_soc_pad(struct sdhci_host *host,
                                       unsigned char signal_voltage)
{
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
        struct xenon_emmc_phy_params *params = priv->phy_params;

        if (!params->pad_ctrl.reg)
                return;

        if (params->pad_ctrl.set_soc_pad)
                params->pad_ctrl.set_soc_pad(host, signal_voltage);
}

/*
 * Enable eMMC PHY HW DLL
 * DLL should be enabled and stable before HS200/SDR104 tuning,
 * and before HS400 data strobe setting.
 */
static int xenon_emmc_phy_enable_dll(struct sdhci_host *host)
{
        u32 reg;
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
        struct xenon_emmc_phy_regs *phy_regs = priv->emmc_phy_regs;
        ktime_t timeout;

        if (WARN_ON(host->clock <= MMC_HIGH_52_MAX_DTR))
                return -EINVAL;

        reg = sdhci_readl(host, phy_regs->dll_ctrl);
        if (reg & XENON_DLL_ENABLE)
                return 0;

        /* Enable DLL */
        reg = sdhci_readl(host, phy_regs->dll_ctrl);
        reg |= (XENON_DLL_ENABLE | XENON_DLL_FAST_LOCK);

        /*
         * Set Phase as 90 degree, which is most common value.
         * Might set another value if necessary.
         * The granularity is 1 degree.
         */
        reg &= ~((XENON_DLL_PHASE_MASK << XENON_DLL_PHSEL0_SHIFT) |
                 (XENON_DLL_PHASE_MASK << XENON_DLL_PHSEL1_SHIFT));
        reg |= ((XENON_DLL_PHASE_90_DEGREE << XENON_DLL_PHSEL0_SHIFT) |
                (XENON_DLL_PHASE_90_DEGREE << XENON_DLL_PHSEL1_SHIFT));

        reg &= ~XENON_DLL_BYPASS_EN;
        reg |= phy_regs->dll_update;
        if (priv->phy_type == EMMC_5_1_PHY)
                reg &= ~XENON_DLL_REFCLK_SEL;
        sdhci_writel(host, reg, phy_regs->dll_ctrl);

        /* Wait max 32 ms */
        timeout = ktime_add_ms(ktime_get(), 32);
        while (1) {
                bool timedout = ktime_after(ktime_get(), timeout);

                if (sdhci_readw(host, XENON_SLOT_EXT_PRESENT_STATE) &
                    XENON_DLL_LOCK_STATE)
                        break;
                if (timedout) {
                        dev_err(mmc_dev(host->mmc), "Wait for DLL Lock time-out\n");
                        return -ETIMEDOUT;
                }
                udelay(100);
        }
        return 0;
}

/*
 * Config to eMMC PHY to prepare for tuning.
 * Enable HW DLL and set the TUNING_STEP
 */
static int xenon_emmc_phy_config_tuning(struct sdhci_host *host)
{
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
        struct xenon_emmc_phy_params *params = priv->phy_params;
        u32 reg, tuning_step;
        int ret;

        if (host->clock <= MMC_HIGH_52_MAX_DTR)
                return -EINVAL;

        ret = xenon_emmc_phy_enable_dll(host);
        if (ret)
                return ret;

        /* Achieve TUNING_STEP with HW DLL help */
        reg = sdhci_readl(host, XENON_SLOT_DLL_CUR_DLY_VAL);
        tuning_step = reg / params->tun_step_divider;
        if (unlikely(tuning_step > XENON_TUNING_STEP_MASK)) {
                dev_warn(mmc_dev(host->mmc),
                         "HS200 TUNING_STEP %d is larger than MAX value\n",
                         tuning_step);
                tuning_step = XENON_TUNING_STEP_MASK;
        }

        /* Set TUNING_STEP for later tuning */
        reg = sdhci_readl(host, XENON_SLOT_OP_STATUS_CTRL);
        reg &= ~(XENON_TUN_CONSECUTIVE_TIMES_MASK <<
                 XENON_TUN_CONSECUTIVE_TIMES_SHIFT);
        reg |= (params->nr_tun_times << XENON_TUN_CONSECUTIVE_TIMES_SHIFT);
        reg &= ~(XENON_TUNING_STEP_MASK << XENON_TUNING_STEP_SHIFT);
        reg |= (tuning_step << XENON_TUNING_STEP_SHIFT);
        sdhci_writel(host, reg, XENON_SLOT_OP_STATUS_CTRL);

        return 0;
}

static void xenon_emmc_phy_disable_strobe(struct sdhci_host *host)
{
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
        u32 reg;

        /* Disable both SDHC Data Strobe and Enhanced Strobe */
        reg = sdhci_readl(host, XENON_SLOT_EMMC_CTRL);
        reg &= ~(XENON_ENABLE_DATA_STROBE | XENON_ENABLE_RESP_STROBE);
        sdhci_writel(host, reg, XENON_SLOT_EMMC_CTRL);

        /* Clear Strobe line Pull down or Pull up */
        if (priv->phy_type == EMMC_5_0_PHY) {
                reg = sdhci_readl(host, XENON_EMMC_5_0_PHY_PAD_CONTROL);
                reg &= ~(XENON_EMMC5_FC_QSP_PD | XENON_EMMC5_FC_QSP_PU);
                sdhci_writel(host, reg, XENON_EMMC_5_0_PHY_PAD_CONTROL);
        } else {
                reg = sdhci_readl(host, XENON_EMMC_PHY_PAD_CONTROL1);
                reg &= ~(XENON_EMMC5_1_FC_QSP_PD | XENON_EMMC5_1_FC_QSP_PU);
                sdhci_writel(host, reg, XENON_EMMC_PHY_PAD_CONTROL1);
        }
}

/* Set HS400 Data Strobe and Enhanced Strobe */
static void xenon_emmc_phy_strobe_delay_adj(struct sdhci_host *host)
{
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
        u32 reg;

        if (WARN_ON(host->timing != MMC_TIMING_MMC_HS400))
                return;

        if (host->clock <= MMC_HIGH_52_MAX_DTR)
                return;

        dev_dbg(mmc_dev(host->mmc), "starts HS400 strobe delay adjustment\n");

        xenon_emmc_phy_enable_dll(host);

        /* Enable SDHC Data Strobe */
        reg = sdhci_readl(host, XENON_SLOT_EMMC_CTRL);
        reg |= XENON_ENABLE_DATA_STROBE;
        /*
         * Enable SDHC Enhanced Strobe if supported
         * Xenon Enhanced Strobe should be enabled only when
         * 1. card is in HS400 mode and
         * 2. SDCLK is higher than 52MHz
         * 3. DLL is enabled
         */
        if (host->mmc->ios.enhanced_strobe)
                reg |= XENON_ENABLE_RESP_STROBE;
        sdhci_writel(host, reg, XENON_SLOT_EMMC_CTRL);

        /* Set Data Strobe Pull down */
        if (priv->phy_type == EMMC_5_0_PHY) {
                reg = sdhci_readl(host, XENON_EMMC_5_0_PHY_PAD_CONTROL);
                reg |= XENON_EMMC5_FC_QSP_PD;
                reg &= ~XENON_EMMC5_FC_QSP_PU;
                sdhci_writel(host, reg, XENON_EMMC_5_0_PHY_PAD_CONTROL);
        } else {
                reg = sdhci_readl(host, XENON_EMMC_PHY_PAD_CONTROL1);
                reg |= XENON_EMMC5_1_FC_QSP_PD;
                reg &= ~XENON_EMMC5_1_FC_QSP_PU;
                sdhci_writel(host, reg, XENON_EMMC_PHY_PAD_CONTROL1);
        }
}

/*
 * If eMMC PHY Slow Mode is required in lower speed mode (SDCLK < 55MHz)
 * in SDR mode, enable Slow Mode to bypass eMMC PHY.
 * SDIO slower SDR mode also requires Slow Mode.
 *
 * If Slow Mode is enabled, return true.
 * Otherwise, return false.
 */
static bool xenon_emmc_phy_slow_mode(struct sdhci_host *host,
                                     unsigned char timing)
{
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
        struct xenon_emmc_phy_params *params = priv->phy_params;
        struct xenon_emmc_phy_regs *phy_regs = priv->emmc_phy_regs;
        u32 reg;
        int ret;

        if (host->clock > MMC_HIGH_52_MAX_DTR)
                return false;

        reg = sdhci_readl(host, phy_regs->timing_adj);
        /* When in slower SDR mode, enable Slow Mode for SDIO
         * or when Slow Mode flag is set
         */
        switch (timing) {
        case MMC_TIMING_LEGACY:
                /*
                 * If Slow Mode is required, enable Slow Mode by default
                 * in early init phase to avoid any potential issue.
                 */
                if (params->slow_mode) {
                        reg |= XENON_TIMING_ADJUST_SLOW_MODE;
                        ret = true;
                } else {
                        reg &= ~XENON_TIMING_ADJUST_SLOW_MODE;
                        ret = false;
                }
                break;
        case MMC_TIMING_UHS_SDR25:
        case MMC_TIMING_UHS_SDR12:
        case MMC_TIMING_SD_HS:
        case MMC_TIMING_MMC_HS:
                if ((priv->init_card_type == MMC_TYPE_SDIO) ||
                    params->slow_mode) {
                        reg |= XENON_TIMING_ADJUST_SLOW_MODE;
                        ret = true;
                        break;
                }
                fallthrough;
        default:
                reg &= ~XENON_TIMING_ADJUST_SLOW_MODE;
                ret = false;
        }

        sdhci_writel(host, reg, phy_regs->timing_adj);
        return ret;
}

/*
 * Set-up eMMC 5.0/5.1 PHY.
 * Specific configuration depends on the current speed mode in use.
 */
static void xenon_emmc_phy_set(struct sdhci_host *host,
                               unsigned char timing)
{
        u32 reg;
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
        struct xenon_emmc_phy_params *params = priv->phy_params;
        struct xenon_emmc_phy_regs *phy_regs = priv->emmc_phy_regs;

        dev_dbg(mmc_dev(host->mmc), "eMMC PHY setting starts\n");

        /* Setup pad, set bit[28] and bits[26:24] */
        reg = sdhci_readl(host, phy_regs->pad_ctrl);
        reg |= (XENON_FC_DQ_RECEN | XENON_FC_CMD_RECEN |
                XENON_FC_QSP_RECEN | XENON_OEN_QSN);
        /* All FC_XX_RECEIVCE should be set as CMOS Type */
        reg |= XENON_FC_ALL_CMOS_RECEIVER;
        sdhci_writel(host, reg, phy_regs->pad_ctrl);

        /* Set CMD and DQ Pull Up */
        if (priv->phy_type == EMMC_5_0_PHY) {
                reg = sdhci_readl(host, XENON_EMMC_5_0_PHY_PAD_CONTROL);
                reg |= (XENON_EMMC5_FC_CMD_PU | XENON_EMMC5_FC_DQ_PU);
                reg &= ~(XENON_EMMC5_FC_CMD_PD | XENON_EMMC5_FC_DQ_PD);
                sdhci_writel(host, reg, XENON_EMMC_5_0_PHY_PAD_CONTROL);
        } else {
                reg = sdhci_readl(host, XENON_EMMC_PHY_PAD_CONTROL1);
                reg |= (XENON_EMMC5_1_FC_CMD_PU | XENON_EMMC5_1_FC_DQ_PU);
                reg &= ~(XENON_EMMC5_1_FC_CMD_PD | XENON_EMMC5_1_FC_DQ_PD);
                sdhci_writel(host, reg, XENON_EMMC_PHY_PAD_CONTROL1);
        }

        if (timing == MMC_TIMING_LEGACY) {
                xenon_emmc_phy_slow_mode(host, timing);
                goto phy_init;
        }

        /*
         * If SDIO card, set SDIO Mode
         * Otherwise, clear SDIO Mode
         */
        reg = sdhci_readl(host, phy_regs->timing_adj);
        if (priv->init_card_type == MMC_TYPE_SDIO)
                reg |= XENON_TIMING_ADJUST_SDIO_MODE;
        else
                reg &= ~XENON_TIMING_ADJUST_SDIO_MODE;
        sdhci_writel(host, reg, phy_regs->timing_adj);

        if (xenon_emmc_phy_slow_mode(host, timing))
                goto phy_init;

        /*
         * Set preferred ZNR and ZPR value
         * The ZNR and ZPR value vary between different boards.
         * Define them both in sdhci-xenon-emmc-phy.h.
         */
        reg = sdhci_readl(host, phy_regs->pad_ctrl2);
        reg &= ~((XENON_ZNR_MASK << XENON_ZNR_SHIFT) | XENON_ZPR_MASK);
        reg |= ((params->znr << XENON_ZNR_SHIFT) | params->zpr);
        sdhci_writel(host, reg, phy_regs->pad_ctrl2);

        /*
         * When setting EMMC_PHY_FUNC_CONTROL register,
         * SD clock should be disabled
         */
        reg = sdhci_readl(host, SDHCI_CLOCK_CONTROL);
        reg &= ~SDHCI_CLOCK_CARD_EN;
        sdhci_writew(host, reg, SDHCI_CLOCK_CONTROL);

        reg = sdhci_readl(host, phy_regs->func_ctrl);
        switch (timing) {
        case MMC_TIMING_MMC_HS400:
                reg |= (XENON_DQ_DDR_MODE_MASK << XENON_DQ_DDR_MODE_SHIFT) |
                       XENON_CMD_DDR_MODE;
                reg &= ~XENON_DQ_ASYNC_MODE;
                break;
        case MMC_TIMING_UHS_DDR50:
        case MMC_TIMING_MMC_DDR52:
                reg |= (XENON_DQ_DDR_MODE_MASK << XENON_DQ_DDR_MODE_SHIFT) |
                       XENON_CMD_DDR_MODE | XENON_DQ_ASYNC_MODE;
                break;
        default:
                reg &= ~((XENON_DQ_DDR_MODE_MASK << XENON_DQ_DDR_MODE_SHIFT) |
                         XENON_CMD_DDR_MODE);
                reg |= XENON_DQ_ASYNC_MODE;
        }
        sdhci_writel(host, reg, phy_regs->func_ctrl);

        /* Enable bus clock */
        reg = sdhci_readl(host, SDHCI_CLOCK_CONTROL);
        reg |= SDHCI_CLOCK_CARD_EN;
        sdhci_writew(host, reg, SDHCI_CLOCK_CONTROL);

        if (timing == MMC_TIMING_MMC_HS400)
                /* Hardware team recommend a value for HS400 */
                sdhci_writel(host, phy_regs->logic_timing_val,
                             phy_regs->logic_timing_adj);
        else
                xenon_emmc_phy_disable_strobe(host);

phy_init:
        xenon_emmc_phy_init(host);

        dev_dbg(mmc_dev(host->mmc), "eMMC PHY setting completes\n");
}

static int get_dt_pad_ctrl_data(struct sdhci_host *host,
                                struct device_node *np,
                                struct xenon_emmc_phy_params *params)
{
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
        int ret = 0;
        const char *name;
        struct resource iomem;

        if (priv->hw_version == XENON_A3700)
                params->pad_ctrl.set_soc_pad = armada_3700_soc_pad_voltage_set;
        else
                return 0;

        if (of_address_to_resource(np, 1, &iomem)) {
                dev_err(mmc_dev(host->mmc), "Unable to find SoC PAD ctrl register address for %pOFn\n",
                        np);
                return -EINVAL;
        }

        params->pad_ctrl.reg = devm_ioremap_resource(mmc_dev(host->mmc),
                                                     &iomem);
        if (IS_ERR(params->pad_ctrl.reg))
                return PTR_ERR(params->pad_ctrl.reg);

        ret = of_property_read_string(np, "marvell,pad-type", &name);
        if (ret) {
                dev_err(mmc_dev(host->mmc), "Unable to determine SoC PHY PAD ctrl type\n");
                return ret;
        }
        if (!strcmp(name, "sd")) {
                params->pad_ctrl.pad_type = SOC_PAD_SD;
        } else if (!strcmp(name, "fixed-1-8v")) {
                params->pad_ctrl.pad_type = SOC_PAD_FIXED_1_8V;
        } else {
                dev_err(mmc_dev(host->mmc), "Unsupported SoC PHY PAD ctrl type %s\n",
                        name);
                return -EINVAL;
        }

        return ret;
}

static int xenon_emmc_phy_parse_params(struct sdhci_host *host,
                                       struct device *dev,
                                       struct xenon_emmc_phy_params *params)
{
        u32 value;

        params->slow_mode = false;
        if (device_property_read_bool(dev, "marvell,xenon-phy-slow-mode"))
                params->slow_mode = true;

        params->znr = XENON_ZNR_DEF_VALUE;
        if (!device_property_read_u32(dev, "marvell,xenon-phy-znr", &value))
                params->znr = value & XENON_ZNR_MASK;

        params->zpr = XENON_ZPR_DEF_VALUE;
        if (!device_property_read_u32(dev, "marvell,xenon-phy-zpr", &value))
                params->zpr = value & XENON_ZPR_MASK;

        params->nr_tun_times = XENON_TUN_CONSECUTIVE_TIMES;
        if (!device_property_read_u32(dev, "marvell,xenon-phy-nr-success-tun",
                                      &value))
                params->nr_tun_times = value & XENON_TUN_CONSECUTIVE_TIMES_MASK;

        params->tun_step_divider = XENON_TUNING_STEP_DIVIDER;
        if (!device_property_read_u32(dev, "marvell,xenon-phy-tun-step-divider",
                                      &value))
                params->tun_step_divider = value & 0xFF;

        if (dev->of_node)
                return get_dt_pad_ctrl_data(host, dev->of_node, params);
        return 0;
}

/* Set SoC PHY Voltage PAD */
void xenon_soc_pad_ctrl(struct sdhci_host *host,
                        unsigned char signal_voltage)
{
        xenon_emmc_phy_set_soc_pad(host, signal_voltage);
}

/*
 * Setting PHY when card is working in High Speed Mode.
 * HS400 set Data Strobe and Enhanced Strobe if it is supported.
 * HS200/SDR104 set tuning config to prepare for tuning.
 */
static int xenon_hs_delay_adj(struct sdhci_host *host)
{
        int ret = 0;

        if (WARN_ON(host->clock <= XENON_DEFAULT_SDCLK_FREQ))
                return -EINVAL;

        switch (host->timing) {
        case MMC_TIMING_MMC_HS400:
                xenon_emmc_phy_strobe_delay_adj(host);
                return 0;
        case MMC_TIMING_MMC_HS200:
        case MMC_TIMING_UHS_SDR104:
                return xenon_emmc_phy_config_tuning(host);
        case MMC_TIMING_MMC_DDR52:
        case MMC_TIMING_UHS_DDR50:
                /*
                 * DDR Mode requires driver to scan Sampling Fixed Delay Line,
                 * to find out a perfect operation sampling point.
                 * It is hard to implement such a scan in host driver
                 * since initiating commands by host driver is not safe.
                 * Thus so far just keep PHY Sampling Fixed Delay in
                 * default value of DDR mode.
                 *
                 * If any timing issue occurs in DDR mode on Marvell products,
                 * please contact maintainer for internal support in Marvell.
                 */
                dev_warn_once(mmc_dev(host->mmc), "Timing issue might occur in DDR mode\n");
                return 0;
        }

        return ret;
}

/*
 * Adjust PHY setting.
 * PHY setting should be adjusted when SDCLK frequency, Bus Width
 * or Speed Mode is changed.
 * Additional config are required when card is working in High Speed mode,
 * after leaving Legacy Mode.
 */
int xenon_phy_adj(struct sdhci_host *host, struct mmc_ios *ios)
{
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
        int ret = 0;

        if (!host->clock) {
                priv->clock = 0;
                return 0;
        }

        /*
         * The timing, frequency or bus width is changed,
         * better to set eMMC PHY based on current setting
         * and adjust Xenon SDHC delay.
         */
        if ((host->clock == priv->clock) &&
            (ios->bus_width == priv->bus_width) &&
            (ios->timing == priv->timing))
                return 0;

        xenon_emmc_phy_set(host, ios->timing);

        /* Update the record */
        priv->bus_width = ios->bus_width;

        priv->timing = ios->timing;
        priv->clock = host->clock;

        /* Legacy mode is a special case */
        if (ios->timing == MMC_TIMING_LEGACY)
                return 0;

        if (host->clock > XENON_DEFAULT_SDCLK_FREQ)
                ret = xenon_hs_delay_adj(host);
        return ret;
}

static int xenon_add_phy(struct device *dev, struct sdhci_host *host,
                         const char *phy_name)
{
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
        int ret;

        priv->phy_type = match_string(phy_types, NR_PHY_TYPES, phy_name);
        if (priv->phy_type < 0) {
                dev_err(mmc_dev(host->mmc),
                        "Unable to determine PHY name %s. Use default eMMC 5.1 PHY\n",
                        phy_name);
                priv->phy_type = EMMC_5_1_PHY;
        }

        ret = xenon_alloc_emmc_phy(host);
        if (ret)
                return ret;

        return xenon_emmc_phy_parse_params(host, dev, priv->phy_params);
}

int xenon_phy_parse_params(struct device *dev, struct sdhci_host *host)
{
        const char *phy_type = NULL;

        if (!device_property_read_string(dev, "marvell,xenon-phy-type", &phy_type))
                return xenon_add_phy(dev, host, phy_type);

        return xenon_add_phy(dev, host, "emmc 5.1 phy");
}