// SPDX-License-Identifier: GPL-2.0-or-later
/*
 * Broadcom Starfighter 2 DSA switch driver
 *
 * Copyright (C) 2014, Broadcom Corporation
 */

#include <linux/list.h>
#include <linux/module.h>
#include <linux/netdevice.h>
#include <linux/interrupt.h>
#include <linux/platform_device.h>
#include <linux/phy.h>
#include <linux/phy_fixed.h>
#include <linux/phylink.h>
#include <linux/mii.h>
#include <linux/clk.h>
#include <linux/of.h>
#include <linux/of_irq.h>
#include <linux/of_address.h>
#include <linux/of_net.h>
#include <linux/of_mdio.h>
#include <net/dsa.h>
#include <linux/ethtool.h>
#include <linux/if_bridge.h>
#include <linux/brcmphy.h>
#include <linux/etherdevice.h>
#include <linux/platform_data/b53.h>

#include "bcm_sf2.h"
#include "bcm_sf2_regs.h"
#include "b53/b53_priv.h"
#include "b53/b53_regs.h"

static u16 bcm_sf2_reg_rgmii_cntrl(struct bcm_sf2_priv *priv, int port)
{
        switch (priv->type) {
        case BCM4908_DEVICE_ID:
                switch (port) {
                case 7:
                        return REG_RGMII_11_CNTRL;
                default:
                        break;
                }
                break;
        default:
                switch (port) {
                case 0:
                        return REG_RGMII_0_CNTRL;
                case 1:
                        return REG_RGMII_1_CNTRL;
                case 2:
                        return REG_RGMII_2_CNTRL;
                default:
                        break;
                }
        }

        WARN_ONCE(1, "Unsupported port %d\n", port);

        /* RO fallback reg */
        return REG_SWITCH_STATUS;
}

/* Return the number of active ports, not counting the IMP (CPU) port */
static unsigned int bcm_sf2_num_active_ports(struct dsa_switch *ds)
{
        struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);
        unsigned int port, count = 0;

        for (port = 0; port < ds->num_ports; port++) {
                if (dsa_is_cpu_port(ds, port))
                        continue;
                if (priv->port_sts[port].enabled)
                        count++;
        }

        return count;
}

static void bcm_sf2_recalc_clock(struct dsa_switch *ds)
{
        struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);
        unsigned long new_rate;
        unsigned int ports_active;
        /* Frequenty in Mhz */
        static const unsigned long rate_table[] = {
                59220000,
                60820000,
                62500000,
                62500000,
        };

        ports_active = bcm_sf2_num_active_ports(ds);
        if (ports_active == 0 || !priv->clk_mdiv)
                return;

        /* If we overflow our table, just use the recommended operational
         * frequency
         */
        if (ports_active > ARRAY_SIZE(rate_table))
                new_rate = 90000000;
        else
                new_rate = rate_table[ports_active - 1];
        clk_set_rate(priv->clk_mdiv, new_rate);
}

static void bcm_sf2_imp_setup(struct dsa_switch *ds, int port)
{
        struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);
        unsigned int i;
        u32 reg, offset;

        /* Enable the port memories */
        reg = core_readl(priv, CORE_MEM_PSM_VDD_CTRL);
        reg &= ~P_TXQ_PSM_VDD(port);
        core_writel(priv, reg, CORE_MEM_PSM_VDD_CTRL);

        /* Enable forwarding */
        core_writel(priv, SW_FWDG_EN, CORE_SWMODE);

        /* Enable IMP port in dumb mode */
        reg = core_readl(priv, CORE_SWITCH_CTRL);
        reg |= MII_DUMB_FWDG_EN;
        core_writel(priv, reg, CORE_SWITCH_CTRL);

        /* Configure Traffic Class to QoS mapping, allow each priority to map
         * to a different queue number
         */
        reg = core_readl(priv, CORE_PORT_TC2_QOS_MAP_PORT(port));
        for (i = 0; i < SF2_NUM_EGRESS_QUEUES; i++)
                reg |= i << (PRT_TO_QID_SHIFT * i);
        core_writel(priv, reg, CORE_PORT_TC2_QOS_MAP_PORT(port));

        b53_brcm_hdr_setup(ds, port);

        if (port == 8) {
                if (priv->type == BCM4908_DEVICE_ID ||
                    priv->type == BCM7445_DEVICE_ID)
                        offset = CORE_STS_OVERRIDE_IMP;
                else
                        offset = CORE_STS_OVERRIDE_IMP2;

                /* Force link status for IMP port */
                reg = core_readl(priv, offset);
                reg |= (MII_SW_OR | LINK_STS);
                if (priv->type == BCM4908_DEVICE_ID)
                        reg |= GMII_SPEED_UP_2G;
                else
                        reg &= ~GMII_SPEED_UP_2G;
                core_writel(priv, reg, offset);

                /* Enable Broadcast, Multicast, Unicast forwarding to IMP port */
                reg = core_readl(priv, CORE_IMP_CTL);
                reg |= (RX_BCST_EN | RX_MCST_EN | RX_UCST_EN);
                reg &= ~(RX_DIS | TX_DIS);
                core_writel(priv, reg, CORE_IMP_CTL);
        } else {
                reg = core_readl(priv, CORE_G_PCTL_PORT(port));
                reg &= ~(RX_DIS | TX_DIS);
                core_writel(priv, reg, CORE_G_PCTL_PORT(port));
        }

        priv->port_sts[port].enabled = true;
}

static void bcm_sf2_gphy_enable_set(struct dsa_switch *ds, bool enable)
{
        struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);
        u32 reg;

        reg = reg_readl(priv, REG_SPHY_CNTRL);
        if (enable) {
                reg |= PHY_RESET;
                reg &= ~(EXT_PWR_DOWN | IDDQ_BIAS | IDDQ_GLOBAL_PWR | CK25_DIS);
                reg_writel(priv, reg, REG_SPHY_CNTRL);
                udelay(21);
                reg = reg_readl(priv, REG_SPHY_CNTRL);
                reg &= ~PHY_RESET;
        } else {
                reg |= EXT_PWR_DOWN | IDDQ_BIAS | PHY_RESET;
                reg_writel(priv, reg, REG_SPHY_CNTRL);
                mdelay(1);
                reg |= CK25_DIS;
        }
        reg_writel(priv, reg, REG_SPHY_CNTRL);

        /* Use PHY-driven LED signaling */
        if (!enable) {
                reg = reg_readl(priv, REG_LED_CNTRL(0));
                reg |= SPDLNK_SRC_SEL;
                reg_writel(priv, reg, REG_LED_CNTRL(0));
        }
}

static inline void bcm_sf2_port_intr_enable(struct bcm_sf2_priv *priv,
                                            int port)
{
        unsigned int off;

        switch (port) {
        case 7:
                off = P7_IRQ_OFF;
                break;
        case 0:
                /* Port 0 interrupts are located on the first bank */
                intrl2_0_mask_clear(priv, P_IRQ_MASK(P0_IRQ_OFF));
                return;
        default:
                off = P_IRQ_OFF(port);
                break;
        }

        intrl2_1_mask_clear(priv, P_IRQ_MASK(off));
}

static inline void bcm_sf2_port_intr_disable(struct bcm_sf2_priv *priv,
                                             int port)
{
        unsigned int off;

        switch (port) {
        case 7:
                off = P7_IRQ_OFF;
                break;
        case 0:
                /* Port 0 interrupts are located on the first bank */
                intrl2_0_mask_set(priv, P_IRQ_MASK(P0_IRQ_OFF));
                intrl2_0_writel(priv, P_IRQ_MASK(P0_IRQ_OFF), INTRL2_CPU_CLEAR);
                return;
        default:
                off = P_IRQ_OFF(port);
                break;
        }

        intrl2_1_mask_set(priv, P_IRQ_MASK(off));
        intrl2_1_writel(priv, P_IRQ_MASK(off), INTRL2_CPU_CLEAR);
}

static int bcm_sf2_port_setup(struct dsa_switch *ds, int port,
                              struct phy_device *phy)
{
        struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);
        unsigned int i;
        u32 reg;

        if (!dsa_is_user_port(ds, port))
                return 0;

        priv->port_sts[port].enabled = true;

        bcm_sf2_recalc_clock(ds);

        /* Clear the memory power down */
        reg = core_readl(priv, CORE_MEM_PSM_VDD_CTRL);
        reg &= ~P_TXQ_PSM_VDD(port);
        core_writel(priv, reg, CORE_MEM_PSM_VDD_CTRL);

        /* Enable Broadcom tags for that port if requested */
        if (priv->brcm_tag_mask & BIT(port))
                b53_brcm_hdr_setup(ds, port);

        /* Configure Traffic Class to QoS mapping, allow each priority to map
         * to a different queue number
         */
        reg = core_readl(priv, CORE_PORT_TC2_QOS_MAP_PORT(port));
        for (i = 0; i < SF2_NUM_EGRESS_QUEUES; i++)
                reg |= i << (PRT_TO_QID_SHIFT * i);
        core_writel(priv, reg, CORE_PORT_TC2_QOS_MAP_PORT(port));

        /* Re-enable the GPHY and re-apply workarounds */
        if (priv->int_phy_mask & 1 << port && priv->hw_params.num_gphy == 1) {
                bcm_sf2_gphy_enable_set(ds, true);
                if (phy) {
                        /* if phy_stop() has been called before, phy
                         * will be in halted state, and phy_start()
                         * will call resume.
                         *
                         * the resume path does not configure back
                         * autoneg settings, and since we hard reset
                         * the phy manually here, we need to reset the
                         * state machine also.
                         */
                        phy->state = PHY_READY;
                        phy_init_hw(phy);
                }
        }

        /* Enable MoCA port interrupts to get notified */
        if (port == priv->moca_port)
                bcm_sf2_port_intr_enable(priv, port);

        /* Set per-queue pause threshold to 32 */
        core_writel(priv, 32, CORE_TXQ_THD_PAUSE_QN_PORT(port));

        /* Set ACB threshold to 24 */
        for (i = 0; i < SF2_NUM_EGRESS_QUEUES; i++) {
                reg = acb_readl(priv, ACB_QUEUE_CFG(port *
                                                    SF2_NUM_EGRESS_QUEUES + i));
                reg &= ~XOFF_THRESHOLD_MASK;
                reg |= 24;
                acb_writel(priv, reg, ACB_QUEUE_CFG(port *
                                                    SF2_NUM_EGRESS_QUEUES + i));
        }

        return b53_enable_port(ds, port, phy);
}

static void bcm_sf2_port_disable(struct dsa_switch *ds, int port)
{
        struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);
        u32 reg;

        /* Disable learning while in WoL mode */
        if (priv->wol_ports_mask & (1 << port)) {
                reg = core_readl(priv, CORE_DIS_LEARN);
                reg |= BIT(port);
                core_writel(priv, reg, CORE_DIS_LEARN);
                return;
        }

        if (port == priv->moca_port)
                bcm_sf2_port_intr_disable(priv, port);

        if (priv->int_phy_mask & 1 << port && priv->hw_params.num_gphy == 1)
                bcm_sf2_gphy_enable_set(ds, false);

        b53_disable_port(ds, port);

        /* Power down the port memory */
        reg = core_readl(priv, CORE_MEM_PSM_VDD_CTRL);
        reg |= P_TXQ_PSM_VDD(port);
        core_writel(priv, reg, CORE_MEM_PSM_VDD_CTRL);

        priv->port_sts[port].enabled = false;

        bcm_sf2_recalc_clock(ds);
}


static int bcm_sf2_sw_indir_rw(struct bcm_sf2_priv *priv, int op, int addr,
                               int regnum, u16 val)
{
        int ret = 0;
        u32 reg;

        reg = reg_readl(priv, REG_SWITCH_CNTRL);
        reg |= MDIO_MASTER_SEL;
        reg_writel(priv, reg, REG_SWITCH_CNTRL);

        /* Page << 8 | offset */
        reg = 0x70;
        reg <<= 2;
        core_writel(priv, addr, reg);

        /* Page << 8 | offset */
        reg = 0x80 << 8 | regnum << 1;
        reg <<= 2;

        if (op)
                ret = core_readl(priv, reg);
        else
                core_writel(priv, val, reg);

        reg = reg_readl(priv, REG_SWITCH_CNTRL);
        reg &= ~MDIO_MASTER_SEL;
        reg_writel(priv, reg, REG_SWITCH_CNTRL);

        return ret & 0xffff;
}

static int bcm_sf2_sw_mdio_read(struct mii_bus *bus, int addr, int regnum)
{
        struct bcm_sf2_priv *priv = bus->priv;

        /* Intercept reads from Broadcom pseudo-PHY address, else, send
         * them to our master MDIO bus controller
         */
        if (addr == BRCM_PSEUDO_PHY_ADDR && priv->indir_phy_mask & BIT(addr))
                return bcm_sf2_sw_indir_rw(priv, 1, addr, regnum, 0);
        else
                return mdiobus_read_nested(priv->master_mii_bus, addr, regnum);
}

static int bcm_sf2_sw_mdio_write(struct mii_bus *bus, int addr, int regnum,
                                 u16 val)
{
        struct bcm_sf2_priv *priv = bus->priv;

        /* Intercept writes to the Broadcom pseudo-PHY address, else,
         * send them to our master MDIO bus controller
         */
        if (addr == BRCM_PSEUDO_PHY_ADDR && priv->indir_phy_mask & BIT(addr))
                return bcm_sf2_sw_indir_rw(priv, 0, addr, regnum, val);
        else
                return mdiobus_write_nested(priv->master_mii_bus, addr,
                                regnum, val);
}

static irqreturn_t bcm_sf2_switch_0_isr(int irq, void *dev_id)
{
        struct dsa_switch *ds = dev_id;
        struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);

        priv->irq0_stat = intrl2_0_readl(priv, INTRL2_CPU_STATUS) &
                                ~priv->irq0_mask;
        intrl2_0_writel(priv, priv->irq0_stat, INTRL2_CPU_CLEAR);

        return IRQ_HANDLED;
}

static irqreturn_t bcm_sf2_switch_1_isr(int irq, void *dev_id)
{
        struct dsa_switch *ds = dev_id;
        struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);

        priv->irq1_stat = intrl2_1_readl(priv, INTRL2_CPU_STATUS) &
                                ~priv->irq1_mask;
        intrl2_1_writel(priv, priv->irq1_stat, INTRL2_CPU_CLEAR);

        if (priv->irq1_stat & P_LINK_UP_IRQ(P7_IRQ_OFF)) {
                priv->port_sts[7].link = true;
                dsa_port_phylink_mac_change(ds, 7, true);
        }
        if (priv->irq1_stat & P_LINK_DOWN_IRQ(P7_IRQ_OFF)) {
                priv->port_sts[7].link = false;
                dsa_port_phylink_mac_change(ds, 7, false);
        }

        return IRQ_HANDLED;
}

static int bcm_sf2_sw_rst(struct bcm_sf2_priv *priv)
{
        unsigned int timeout = 1000;
        u32 reg;
        int ret;

        /* The watchdog reset does not work on 7278, we need to hit the
         * "external" reset line through the reset controller.
         */
        if (priv->type == BCM7278_DEVICE_ID) {
                ret = reset_control_assert(priv->rcdev);
                if (ret)
                        return ret;

                return reset_control_deassert(priv->rcdev);
        }

        reg = core_readl(priv, CORE_WATCHDOG_CTRL);
        reg |= SOFTWARE_RESET | EN_CHIP_RST | EN_SW_RESET;
        core_writel(priv, reg, CORE_WATCHDOG_CTRL);

        do {
                reg = core_readl(priv, CORE_WATCHDOG_CTRL);
                if (!(reg & SOFTWARE_RESET))
                        break;

                usleep_range(1000, 2000);
        } while (timeout-- > 0);

        if (timeout == 0)
                return -ETIMEDOUT;

        return 0;
}

static void bcm_sf2_crossbar_setup(struct bcm_sf2_priv *priv)
{
        struct device *dev = priv->dev->ds->dev;
        int shift;
        u32 mask;
        u32 reg;
        int i;

        mask = BIT(priv->num_crossbar_int_ports) - 1;

        reg = reg_readl(priv, REG_CROSSBAR);
        switch (priv->type) {
        case BCM4908_DEVICE_ID:
                shift = CROSSBAR_BCM4908_INT_P7 * priv->num_crossbar_int_ports;
                reg &= ~(mask << shift);
                if (0) /* FIXME */
                        reg |= CROSSBAR_BCM4908_EXT_SERDES << shift;
                else if (priv->int_phy_mask & BIT(7))
                        reg |= CROSSBAR_BCM4908_EXT_GPHY4 << shift;
                else if (phy_interface_mode_is_rgmii(priv->port_sts[7].mode))
                        reg |= CROSSBAR_BCM4908_EXT_RGMII << shift;
                else if (WARN(1, "Invalid port mode\n"))
                        return;
                break;
        default:
                return;
        }
        reg_writel(priv, reg, REG_CROSSBAR);

        reg = reg_readl(priv, REG_CROSSBAR);
        for (i = 0; i < priv->num_crossbar_int_ports; i++) {
                shift = i * priv->num_crossbar_int_ports;

                dev_dbg(dev, "crossbar int port #%d - ext port #%d\n", i,
                        (reg >> shift) & mask);
        }
}

static void bcm_sf2_intr_disable(struct bcm_sf2_priv *priv)
{
        intrl2_0_mask_set(priv, 0xffffffff);
        intrl2_0_writel(priv, 0xffffffff, INTRL2_CPU_CLEAR);
        intrl2_1_mask_set(priv, 0xffffffff);
        intrl2_1_writel(priv, 0xffffffff, INTRL2_CPU_CLEAR);
}

static void bcm_sf2_identify_ports(struct bcm_sf2_priv *priv,
                                   struct device_node *dn)
{
        struct device *dev = priv->dev->ds->dev;
        struct bcm_sf2_port_status *port_st;
        struct device_node *port;
        unsigned int port_num;
        struct property *prop;
        int err;

        priv->moca_port = -1;

        for_each_available_child_of_node(dn, port) {
                if (of_property_read_u32(port, "reg", &port_num))
                        continue;

                if (port_num >= DSA_MAX_PORTS) {
                        dev_err(dev, "Invalid port number %d\n", port_num);
                        continue;
                }

                port_st = &priv->port_sts[port_num];

                /* Internal PHYs get assigned a specific 'phy-mode' property
                 * value: "internal" to help flag them before MDIO probing
                 * has completed, since they might be turned off at that
                 * time
                 */
                err = of_get_phy_mode(port, &port_st->mode);
                if (err)
                        continue;

                if (port_st->mode == PHY_INTERFACE_MODE_INTERNAL)
                        priv->int_phy_mask |= 1 << port_num;

                if (port_st->mode == PHY_INTERFACE_MODE_MOCA)
                        priv->moca_port = port_num;

                if (of_property_read_bool(port, "brcm,use-bcm-hdr"))
                        priv->brcm_tag_mask |= 1 << port_num;

                /* Ensure that port 5 is not picked up as a DSA CPU port
                 * flavour but a regular port instead. We should be using
                 * devlink to be able to set the port flavour.
                 */
                if (port_num == 5 && priv->type == BCM7278_DEVICE_ID) {
                        prop = of_find_property(port, "ethernet", NULL);
                        if (prop)
                                of_remove_property(port, prop);
                }
        }
}

static int bcm_sf2_mdio_register(struct dsa_switch *ds)
{
        struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);
        struct device_node *dn, *child;
        struct phy_device *phydev;
        struct property *prop;
        static int index;
        int err, reg;

        /* Find our integrated MDIO bus node */
        dn = of_find_compatible_node(NULL, NULL, "brcm,unimac-mdio");
        priv->master_mii_bus = of_mdio_find_bus(dn);
        if (!priv->master_mii_bus) {
                of_node_put(dn);
                return -EPROBE_DEFER;
        }

        get_device(&priv->master_mii_bus->dev);
        priv->master_mii_dn = dn;

        priv->slave_mii_bus = devm_mdiobus_alloc(ds->dev);
        if (!priv->slave_mii_bus) {
                of_node_put(dn);
                return -ENOMEM;
        }

        priv->slave_mii_bus->priv = priv;
        priv->slave_mii_bus->name = "sf2 slave mii";
        priv->slave_mii_bus->read = bcm_sf2_sw_mdio_read;
        priv->slave_mii_bus->write = bcm_sf2_sw_mdio_write;
        snprintf(priv->slave_mii_bus->id, MII_BUS_ID_SIZE, "sf2-%d",
                 index++);
        priv->slave_mii_bus->dev.of_node = dn;

        /* Include the pseudo-PHY address to divert reads towards our
         * workaround. This is only required for 7445D0, since 7445E0
         * disconnects the internal switch pseudo-PHY such that we can use the
         * regular SWITCH_MDIO master controller instead.
         *
         * Here we flag the pseudo PHY as needing special treatment and would
         * otherwise make all other PHY read/writes go to the master MDIO bus
         * controller that comes with this switch backed by the "mdio-unimac"
         * driver.
         */
        if (of_machine_is_compatible("brcm,bcm7445d0"))
                priv->indir_phy_mask |= (1 << BRCM_PSEUDO_PHY_ADDR) | (1 << 0);
        else
                priv->indir_phy_mask = 0;

        ds->phys_mii_mask = priv->indir_phy_mask;
        ds->slave_mii_bus = priv->slave_mii_bus;
        priv->slave_mii_bus->parent = ds->dev->parent;
        priv->slave_mii_bus->phy_mask = ~priv->indir_phy_mask;

        /* We need to make sure that of_phy_connect() will not work by
         * removing the 'phandle' and 'linux,phandle' properties and
         * unregister the existing PHY device that was already registered.
         */
        for_each_available_child_of_node(dn, child) {
                if (of_property_read_u32(child, "reg", &reg) ||
                    reg >= PHY_MAX_ADDR)
                        continue;

                if (!(priv->indir_phy_mask & BIT(reg)))
                        continue;

                prop = of_find_property(child, "phandle", NULL);
                if (prop)
                        of_remove_property(child, prop);

                prop = of_find_property(child, "linux,phandle", NULL);
                if (prop)
                        of_remove_property(child, prop);

                phydev = of_phy_find_device(child);
                if (phydev)
                        phy_device_remove(phydev);
        }

        err = mdiobus_register(priv->slave_mii_bus);
        if (err && dn)
                of_node_put(dn);

        return err;
}

static void bcm_sf2_mdio_unregister(struct bcm_sf2_priv *priv)
{
        mdiobus_unregister(priv->slave_mii_bus);
        of_node_put(priv->master_mii_dn);
}

static u32 bcm_sf2_sw_get_phy_flags(struct dsa_switch *ds, int port)
{
        struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);

        /* The BCM7xxx PHY driver expects to find the integrated PHY revision
         * in bits 15:8 and the patch level in bits 7:0 which is exactly what
         * the REG_PHY_REVISION register layout is.
         */
        if (priv->int_phy_mask & BIT(port))
                return priv->hw_params.gphy_rev;
        else
                return 0;
}

static void bcm_sf2_sw_validate(struct dsa_switch *ds, int port,
                                unsigned long *supported,
                                struct phylink_link_state *state)
{
        struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);
        __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };

        if (!phy_interface_mode_is_rgmii(state->interface) &&
            state->interface != PHY_INTERFACE_MODE_MII &&
            state->interface != PHY_INTERFACE_MODE_REVMII &&
            state->interface != PHY_INTERFACE_MODE_GMII &&
            state->interface != PHY_INTERFACE_MODE_INTERNAL &&
            state->interface != PHY_INTERFACE_MODE_MOCA) {
                bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
                if (port != core_readl(priv, CORE_IMP0_PRT_ID))
                        dev_err(ds->dev,
                                "Unsupported interface: %d for port %d\n",
                                state->interface, port);
                return;
        }

        /* Allow all the expected bits */
        phylink_set(mask, Autoneg);
        phylink_set_port_modes(mask);
        phylink_set(mask, Pause);
        phylink_set(mask, Asym_Pause);

        /* With the exclusion of MII and Reverse MII, we support Gigabit,
         * including Half duplex
         */
        if (state->interface != PHY_INTERFACE_MODE_MII &&
            state->interface != PHY_INTERFACE_MODE_REVMII) {
                phylink_set(mask, 1000baseT_Full);
                phylink_set(mask, 1000baseT_Half);
        }

        phylink_set(mask, 10baseT_Half);
        phylink_set(mask, 10baseT_Full);
        phylink_set(mask, 100baseT_Half);
        phylink_set(mask, 100baseT_Full);

        bitmap_and(supported, supported, mask,
                   __ETHTOOL_LINK_MODE_MASK_NBITS);
        bitmap_and(state->advertising, state->advertising, mask,
                   __ETHTOOL_LINK_MODE_MASK_NBITS);
}

static void bcm_sf2_sw_mac_config(struct dsa_switch *ds, int port,
                                  unsigned int mode,
                                  const struct phylink_link_state *state)
{
        struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);
        u32 id_mode_dis = 0, port_mode;
        u32 reg_rgmii_ctrl;
        u32 reg;

        if (port == core_readl(priv, CORE_IMP0_PRT_ID))
                return;

        switch (state->interface) {
        case PHY_INTERFACE_MODE_RGMII:
                id_mode_dis = 1;
                fallthrough;
        case PHY_INTERFACE_MODE_RGMII_TXID:
                port_mode = EXT_GPHY;
                break;
        case PHY_INTERFACE_MODE_MII:
                port_mode = EXT_EPHY;
                break;
        case PHY_INTERFACE_MODE_REVMII:
                port_mode = EXT_REVMII;
                break;
        default:
                /* Nothing required for all other PHYs: internal and MoCA */
                return;
        }

        reg_rgmii_ctrl = bcm_sf2_reg_rgmii_cntrl(priv, port);

        /* Clear id_mode_dis bit, and the existing port mode, let
         * RGMII_MODE_EN bet set by mac_link_{up,down}
         */
        reg = reg_readl(priv, reg_rgmii_ctrl);
        reg &= ~ID_MODE_DIS;
        reg &= ~(PORT_MODE_MASK << PORT_MODE_SHIFT);

        reg |= port_mode;
        if (id_mode_dis)
                reg |= ID_MODE_DIS;

        reg_writel(priv, reg, reg_rgmii_ctrl);
}

static void bcm_sf2_sw_mac_link_set(struct dsa_switch *ds, int port,
                                    phy_interface_t interface, bool link)
{
        struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);
        u32 reg_rgmii_ctrl;
        u32 reg;

        if (!phy_interface_mode_is_rgmii(interface) &&
            interface != PHY_INTERFACE_MODE_MII &&
            interface != PHY_INTERFACE_MODE_REVMII)
                return;

        reg_rgmii_ctrl = bcm_sf2_reg_rgmii_cntrl(priv, port);

        /* If the link is down, just disable the interface to conserve power */
        reg = reg_readl(priv, reg_rgmii_ctrl);
        if (link)
                reg |= RGMII_MODE_EN;
        else
                reg &= ~RGMII_MODE_EN;
        reg_writel(priv, reg, reg_rgmii_ctrl);
}

static void bcm_sf2_sw_mac_link_down(struct dsa_switch *ds, int port,
                                     unsigned int mode,
                                     phy_interface_t interface)
{
        struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);
        u32 reg, offset;

        if (port != core_readl(priv, CORE_IMP0_PRT_ID)) {
                if (priv->type == BCM4908_DEVICE_ID ||
                    priv->type == BCM7445_DEVICE_ID)
                        offset = CORE_STS_OVERRIDE_GMIIP_PORT(port);
                else
                        offset = CORE_STS_OVERRIDE_GMIIP2_PORT(port);

                reg = core_readl(priv, offset);
                reg &= ~LINK_STS;
                core_writel(priv, reg, offset);
        }

        bcm_sf2_sw_mac_link_set(ds, port, interface, false);
}

static void bcm_sf2_sw_mac_link_up(struct dsa_switch *ds, int port,
                                   unsigned int mode,
                                   phy_interface_t interface,
                                   struct phy_device *phydev,
                                   int speed, int duplex,
                                   bool tx_pause, bool rx_pause)
{
        struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);
        struct ethtool_eee *p = &priv->dev->ports[port].eee;

        bcm_sf2_sw_mac_link_set(ds, port, interface, true);

        if (port != core_readl(priv, CORE_IMP0_PRT_ID)) {
                u32 reg_rgmii_ctrl = 0;
                u32 reg, offset;

                if (priv->type == BCM4908_DEVICE_ID ||
                    priv->type == BCM7445_DEVICE_ID)
                        offset = CORE_STS_OVERRIDE_GMIIP_PORT(port);
                else
                        offset = CORE_STS_OVERRIDE_GMIIP2_PORT(port);

                if (interface == PHY_INTERFACE_MODE_RGMII ||
                    interface == PHY_INTERFACE_MODE_RGMII_TXID ||
                    interface == PHY_INTERFACE_MODE_MII ||
                    interface == PHY_INTERFACE_MODE_REVMII) {
                        reg_rgmii_ctrl = bcm_sf2_reg_rgmii_cntrl(priv, port);
                        reg = reg_readl(priv, reg_rgmii_ctrl);
                        reg &= ~(RX_PAUSE_EN | TX_PAUSE_EN);

                        if (tx_pause)
                                reg |= TX_PAUSE_EN;
                        if (rx_pause)
                                reg |= RX_PAUSE_EN;

                        reg_writel(priv, reg, reg_rgmii_ctrl);
                }

                reg = SW_OVERRIDE | LINK_STS;
                switch (speed) {
                case SPEED_1000:
                        reg |= SPDSTS_1000 << SPEED_SHIFT;
                        break;
                case SPEED_100:
                        reg |= SPDSTS_100 << SPEED_SHIFT;
                        break;
                }

                if (duplex == DUPLEX_FULL)
                        reg |= DUPLX_MODE;

                core_writel(priv, reg, offset);
        }

        if (mode == MLO_AN_PHY && phydev)
                p->eee_enabled = b53_eee_init(ds, port, phydev);
}

static void bcm_sf2_sw_fixed_state(struct dsa_switch *ds, int port,
                                   struct phylink_link_state *status)
{
        struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);

        status->link = false;

        /* MoCA port is special as we do not get link status from CORE_LNKSTS,
         * which means that we need to force the link at the port override
         * level to get the data to flow. We do use what the interrupt handler
         * did determine before.
         *
         * For the other ports, we just force the link status, since this is
         * a fixed PHY device.
         */
        if (port == priv->moca_port) {
                status->link = priv->port_sts[port].link;
                /* For MoCA interfaces, also force a link down notification
                 * since some version of the user-space daemon (mocad) use
                 * cmd->autoneg to force the link, which messes up the PHY
                 * state machine and make it go in PHY_FORCING state instead.
                 */
                if (!status->link)
                        netif_carrier_off(dsa_to_port(ds, port)->slave);
                status->duplex = DUPLEX_FULL;
        } else {
                status->link = true;
        }
}

static void bcm_sf2_enable_acb(struct dsa_switch *ds)
{
        struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);
        u32 reg;

        /* Enable ACB globally */
        reg = acb_readl(priv, ACB_CONTROL);
        reg |= (ACB_FLUSH_MASK << ACB_FLUSH_SHIFT);
        acb_writel(priv, reg, ACB_CONTROL);
        reg &= ~(ACB_FLUSH_MASK << ACB_FLUSH_SHIFT);
        reg |= ACB_EN | ACB_ALGORITHM;
        acb_writel(priv, reg, ACB_CONTROL);
}

static int bcm_sf2_sw_suspend(struct dsa_switch *ds)
{
        struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);
        unsigned int port;

        bcm_sf2_intr_disable(priv);

        /* Disable all ports physically present including the IMP
         * port, the other ones have already been disabled during
         * bcm_sf2_sw_setup
         */
        for (port = 0; port < ds->num_ports; port++) {
                if (dsa_is_user_port(ds, port) || dsa_is_cpu_port(ds, port))
                        bcm_sf2_port_disable(ds, port);
        }

        if (!priv->wol_ports_mask)
                clk_disable_unprepare(priv->clk);

        return 0;
}

static int bcm_sf2_sw_resume(struct dsa_switch *ds)
{
        struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);
        int ret;

        if (!priv->wol_ports_mask)
                clk_prepare_enable(priv->clk);

        ret = bcm_sf2_sw_rst(priv);
        if (ret) {
                pr_err("%s: failed to software reset switch\n", __func__);
                return ret;
        }

        bcm_sf2_crossbar_setup(priv);

        ret = bcm_sf2_cfp_resume(ds);
        if (ret)
                return ret;

        if (priv->hw_params.num_gphy == 1)
                bcm_sf2_gphy_enable_set(ds, true);

        ds->ops->setup(ds);

        return 0;
}

static void bcm_sf2_sw_get_wol(struct dsa_switch *ds, int port,
                               struct ethtool_wolinfo *wol)
{
        struct net_device *p = dsa_to_port(ds, port)->cpu_dp->master;
        struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);
        struct ethtool_wolinfo pwol = { };

        /* Get the parent device WoL settings */
        if (p->ethtool_ops->get_wol)
                p->ethtool_ops->get_wol(p, &pwol);

        /* Advertise the parent device supported settings */
        wol->supported = pwol.supported;
        memset(&wol->sopass, 0, sizeof(wol->sopass));

        if (pwol.wolopts & WAKE_MAGICSECURE)
                memcpy(&wol->sopass, pwol.sopass, sizeof(wol->sopass));

        if (priv->wol_ports_mask & (1 << port))
                wol->wolopts = pwol.wolopts;
        else
                wol->wolopts = 0;
}

static int bcm_sf2_sw_set_wol(struct dsa_switch *ds, int port,
                              struct ethtool_wolinfo *wol)
{
        struct net_device *p = dsa_to_port(ds, port)->cpu_dp->master;
        struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);
        s8 cpu_port = dsa_to_port(ds, port)->cpu_dp->index;
        struct ethtool_wolinfo pwol =  { };

        if (p->ethtool_ops->get_wol)
                p->ethtool_ops->get_wol(p, &pwol);
        if (wol->wolopts & ~pwol.supported)
                return -EINVAL;

        if (wol->wolopts)

                priv->wol_ports_mask |= (1 << port);
        else
                priv->wol_ports_mask &= ~(1 << port);

        /* If we have at least one port enabled, make sure the CPU port
         * is also enabled. If the CPU port is the last one enabled, we disable
         * it since this configuration does not make sense.
         */
        if (priv->wol_ports_mask && priv->wol_ports_mask != (1 << cpu_port))
                priv->wol_ports_mask |= (1 << cpu_port);
        else
                priv->wol_ports_mask &= ~(1 << cpu_port);

        return p->ethtool_ops->set_wol(p, wol);
}

static int bcm_sf2_sw_setup(struct dsa_switch *ds)
{
        struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);
        unsigned int port;

        /* Enable all valid ports and disable those unused */
        for (port = 0; port < priv->hw_params.num_ports; port++) {
                /* IMP port receives special treatment */
                if (dsa_is_user_port(ds, port))
                        bcm_sf2_port_setup(ds, port, NULL);
                else if (dsa_is_cpu_port(ds, port))
                        bcm_sf2_imp_setup(ds, port);
                else
                        bcm_sf2_port_disable(ds, port);
        }

        b53_configure_vlan(ds);
        bcm_sf2_enable_acb(ds);

        return b53_setup_devlink_resources(ds);
}

static void bcm_sf2_sw_teardown(struct dsa_switch *ds)
{
        dsa_devlink_resources_unregister(ds);
}

/* The SWITCH_CORE register space is managed by b53 but operates on a page +
 * register basis so we need to translate that into an address that the
 * bus-glue understands.
 */
#define SF2_PAGE_REG_MKADDR(page, reg)  ((page) << 10 | (reg) << 2)

static int bcm_sf2_core_read8(struct b53_device *dev, u8 page, u8 reg,
                              u8 *val)
{
        struct bcm_sf2_priv *priv = dev->priv;

        *val = core_readl(priv, SF2_PAGE_REG_MKADDR(page, reg));

        return 0;
}

static int bcm_sf2_core_read16(struct b53_device *dev, u8 page, u8 reg,
                               u16 *val)
{
        struct bcm_sf2_priv *priv = dev->priv;

        *val = core_readl(priv, SF2_PAGE_REG_MKADDR(page, reg));

        return 0;
}

static int bcm_sf2_core_read32(struct b53_device *dev, u8 page, u8 reg,
                               u32 *val)
{
        struct bcm_sf2_priv *priv = dev->priv;

        *val = core_readl(priv, SF2_PAGE_REG_MKADDR(page, reg));

        return 0;
}

static int bcm_sf2_core_read64(struct b53_device *dev, u8 page, u8 reg,
                               u64 *val)
{
        struct bcm_sf2_priv *priv = dev->priv;

        *val = core_readq(priv, SF2_PAGE_REG_MKADDR(page, reg));

        return 0;
}

static int bcm_sf2_core_write8(struct b53_device *dev, u8 page, u8 reg,
                               u8 value)
{
        struct bcm_sf2_priv *priv = dev->priv;

        core_writel(priv, value, SF2_PAGE_REG_MKADDR(page, reg));

        return 0;
}

static int bcm_sf2_core_write16(struct b53_device *dev, u8 page, u8 reg,
                                u16 value)
{
        struct bcm_sf2_priv *priv = dev->priv;

        core_writel(priv, value, SF2_PAGE_REG_MKADDR(page, reg));

        return 0;
}

static int bcm_sf2_core_write32(struct b53_device *dev, u8 page, u8 reg,
                                u32 value)
{
        struct bcm_sf2_priv *priv = dev->priv;

        core_writel(priv, value, SF2_PAGE_REG_MKADDR(page, reg));

        return 0;
}

static int bcm_sf2_core_write64(struct b53_device *dev, u8 page, u8 reg,
                                u64 value)
{
        struct bcm_sf2_priv *priv = dev->priv;

        core_writeq(priv, value, SF2_PAGE_REG_MKADDR(page, reg));

        return 0;
}

static const struct b53_io_ops bcm_sf2_io_ops = {
        .read8  = bcm_sf2_core_read8,
        .read16 = bcm_sf2_core_read16,
        .read32 = bcm_sf2_core_read32,
        .read48 = bcm_sf2_core_read64,
        .read64 = bcm_sf2_core_read64,
        .write8 = bcm_sf2_core_write8,
        .write16 = bcm_sf2_core_write16,
        .write32 = bcm_sf2_core_write32,
        .write48 = bcm_sf2_core_write64,
        .write64 = bcm_sf2_core_write64,
};

static void bcm_sf2_sw_get_strings(struct dsa_switch *ds, int port,
                                   u32 stringset, uint8_t *data)
{
        int cnt = b53_get_sset_count(ds, port, stringset);

        b53_get_strings(ds, port, stringset, data);
        bcm_sf2_cfp_get_strings(ds, port, stringset,
                                data + cnt * ETH_GSTRING_LEN);
}

static void bcm_sf2_sw_get_ethtool_stats(struct dsa_switch *ds, int port,
                                         uint64_t *data)
{
        int cnt = b53_get_sset_count(ds, port, ETH_SS_STATS);

        b53_get_ethtool_stats(ds, port, data);
        bcm_sf2_cfp_get_ethtool_stats(ds, port, data + cnt);
}

static int bcm_sf2_sw_get_sset_count(struct dsa_switch *ds, int port,
                                     int sset)
{
        int cnt = b53_get_sset_count(ds, port, sset);

        if (cnt < 0)
                return cnt;

        cnt += bcm_sf2_cfp_get_sset_count(ds, port, sset);

        return cnt;
}

static const struct dsa_switch_ops bcm_sf2_ops = {
        .get_tag_protocol       = b53_get_tag_protocol,
        .setup                  = bcm_sf2_sw_setup,
        .teardown               = bcm_sf2_sw_teardown,
        .get_strings            = bcm_sf2_sw_get_strings,
        .get_ethtool_stats      = bcm_sf2_sw_get_ethtool_stats,
        .get_sset_count         = bcm_sf2_sw_get_sset_count,
        .get_ethtool_phy_stats  = b53_get_ethtool_phy_stats,
        .get_phy_flags          = bcm_sf2_sw_get_phy_flags,
        .phylink_validate       = bcm_sf2_sw_validate,
        .phylink_mac_config     = bcm_sf2_sw_mac_config,
        .phylink_mac_link_down  = bcm_sf2_sw_mac_link_down,
        .phylink_mac_link_up    = bcm_sf2_sw_mac_link_up,
        .phylink_fixed_state    = bcm_sf2_sw_fixed_state,
        .suspend                = bcm_sf2_sw_suspend,
        .resume                 = bcm_sf2_sw_resume,
        .get_wol                = bcm_sf2_sw_get_wol,
        .set_wol                = bcm_sf2_sw_set_wol,
        .port_enable            = bcm_sf2_port_setup,
        .port_disable           = bcm_sf2_port_disable,
        .get_mac_eee            = b53_get_mac_eee,
        .set_mac_eee            = b53_set_mac_eee,
        .port_bridge_join       = b53_br_join,
        .port_bridge_leave      = b53_br_leave,
        .port_pre_bridge_flags  = b53_br_flags_pre,
        .port_bridge_flags      = b53_br_flags,
        .port_stp_state_set     = b53_br_set_stp_state,
        .port_fast_age          = b53_br_fast_age,
        .port_vlan_filtering    = b53_vlan_filtering,
        .port_vlan_add          = b53_vlan_add,
        .port_vlan_del          = b53_vlan_del,
        .port_fdb_dump          = b53_fdb_dump,
        .port_fdb_add           = b53_fdb_add,
        .port_fdb_del           = b53_fdb_del,
        .get_rxnfc              = bcm_sf2_get_rxnfc,
        .set_rxnfc              = bcm_sf2_set_rxnfc,
        .port_mirror_add        = b53_mirror_add,
        .port_mirror_del        = b53_mirror_del,
        .port_mdb_add           = b53_mdb_add,
        .port_mdb_del           = b53_mdb_del,
};

struct bcm_sf2_of_data {
        u32 type;
        const u16 *reg_offsets;
        unsigned int core_reg_align;
        unsigned int num_cfp_rules;
        unsigned int num_crossbar_int_ports;
};

static const u16 bcm_sf2_4908_reg_offsets[] = {
        [REG_SWITCH_CNTRL]      = 0x00,
        [REG_SWITCH_STATUS]     = 0x04,
        [REG_DIR_DATA_WRITE]    = 0x08,
        [REG_DIR_DATA_READ]     = 0x0c,
        [REG_SWITCH_REVISION]   = 0x10,
        [REG_PHY_REVISION]      = 0x14,
        [REG_SPHY_CNTRL]        = 0x24,
        [REG_CROSSBAR]          = 0xc8,
        [REG_RGMII_11_CNTRL]    = 0x014c,
        [REG_LED_0_CNTRL]       = 0x40,
        [REG_LED_1_CNTRL]       = 0x4c,
        [REG_LED_2_CNTRL]       = 0x58,
};

static const struct bcm_sf2_of_data bcm_sf2_4908_data = {
        .type           = BCM4908_DEVICE_ID,
        .core_reg_align = 0,
        .reg_offsets    = bcm_sf2_4908_reg_offsets,
        .num_cfp_rules  = 256,
        .num_crossbar_int_ports = 2,
};

/* Register offsets for the SWITCH_REG_* block */
static const u16 bcm_sf2_7445_reg_offsets[] = {
        [REG_SWITCH_CNTRL]      = 0x00,
        [REG_SWITCH_STATUS]     = 0x04,
        [REG_DIR_DATA_WRITE]    = 0x08,
        [REG_DIR_DATA_READ]     = 0x0C,
        [REG_SWITCH_REVISION]   = 0x18,
        [REG_PHY_REVISION]      = 0x1C,
        [REG_SPHY_CNTRL]        = 0x2C,
        [REG_RGMII_0_CNTRL]     = 0x34,
        [REG_RGMII_1_CNTRL]     = 0x40,
        [REG_RGMII_2_CNTRL]     = 0x4c,
        [REG_LED_0_CNTRL]       = 0x90,
        [REG_LED_1_CNTRL]       = 0x94,
        [REG_LED_2_CNTRL]       = 0x98,
};

static const struct bcm_sf2_of_data bcm_sf2_7445_data = {
        .type           = BCM7445_DEVICE_ID,
        .core_reg_align = 0,
        .reg_offsets    = bcm_sf2_7445_reg_offsets,
        .num_cfp_rules  = 256,
};

static const u16 bcm_sf2_7278_reg_offsets[] = {
        [REG_SWITCH_CNTRL]      = 0x00,
        [REG_SWITCH_STATUS]     = 0x04,
        [REG_DIR_DATA_WRITE]    = 0x08,
        [REG_DIR_DATA_READ]     = 0x0c,
        [REG_SWITCH_REVISION]   = 0x10,
        [REG_PHY_REVISION]      = 0x14,
        [REG_SPHY_CNTRL]        = 0x24,
        [REG_RGMII_0_CNTRL]     = 0xe0,
        [REG_RGMII_1_CNTRL]     = 0xec,
        [REG_RGMII_2_CNTRL]     = 0xf8,
        [REG_LED_0_CNTRL]       = 0x40,
        [REG_LED_1_CNTRL]       = 0x4c,
        [REG_LED_2_CNTRL]       = 0x58,
};

static const struct bcm_sf2_of_data bcm_sf2_7278_data = {
        .type           = BCM7278_DEVICE_ID,
        .core_reg_align = 1,
        .reg_offsets    = bcm_sf2_7278_reg_offsets,
        .num_cfp_rules  = 128,
};

static const struct of_device_id bcm_sf2_of_match[] = {
        { .compatible = "brcm,bcm4908-switch",
          .data = &bcm_sf2_4908_data
        },
        { .compatible = "brcm,bcm7445-switch-v4.0",
          .data = &bcm_sf2_7445_data
        },
        { .compatible = "brcm,bcm7278-switch-v4.0",
          .data = &bcm_sf2_7278_data
        },
        { .compatible = "brcm,bcm7278-switch-v4.8",
          .data = &bcm_sf2_7278_data
        },
        { /* sentinel */ },
};
MODULE_DEVICE_TABLE(of, bcm_sf2_of_match);

static int bcm_sf2_sw_probe(struct platform_device *pdev)
{
        const char *reg_names[BCM_SF2_REGS_NUM] = BCM_SF2_REGS_NAME;
        struct device_node *dn = pdev->dev.of_node;
        const struct of_device_id *of_id = NULL;
        const struct bcm_sf2_of_data *data;
        struct b53_platform_data *pdata;
        struct dsa_switch_ops *ops;
        struct device_node *ports;
        struct bcm_sf2_priv *priv;
        struct b53_device *dev;
        struct dsa_switch *ds;
        void __iomem **base;
        unsigned int i;
        u32 reg, rev;
        int ret;

        priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
        if (!priv)
                return -ENOMEM;

        ops = devm_kzalloc(&pdev->dev, sizeof(*ops), GFP_KERNEL);
        if (!ops)
                return -ENOMEM;

        dev = b53_switch_alloc(&pdev->dev, &bcm_sf2_io_ops, priv);
        if (!dev)
                return -ENOMEM;

        pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
        if (!pdata)
                return -ENOMEM;

        of_id = of_match_node(bcm_sf2_of_match, dn);
        if (!of_id || !of_id->data)
                return -EINVAL;

        data = of_id->data;

        /* Set SWITCH_REG register offsets and SWITCH_CORE align factor */
        priv->type = data->type;
        priv->reg_offsets = data->reg_offsets;
        priv->core_reg_align = data->core_reg_align;
        priv->num_cfp_rules = data->num_cfp_rules;
        priv->num_crossbar_int_ports = data->num_crossbar_int_ports;

        priv->rcdev = devm_reset_control_get_optional_exclusive(&pdev->dev,
                                                                "switch");
        if (IS_ERR(priv->rcdev))
                return PTR_ERR(priv->rcdev);

        /* Auto-detection using standard registers will not work, so
         * provide an indication of what kind of device we are for
         * b53_common to work with
         */
        pdata->chip_id = priv->type;
        dev->pdata = pdata;

        priv->dev = dev;
        ds = dev->ds;
        ds->ops = &bcm_sf2_ops;

        /* Advertise the 8 egress queues */
        ds->num_tx_queues = SF2_NUM_EGRESS_QUEUES;

        dev_set_drvdata(&pdev->dev, priv);

        spin_lock_init(&priv->indir_lock);
        mutex_init(&priv->cfp.lock);
        INIT_LIST_HEAD(&priv->cfp.rules_list);

        /* CFP rule #0 cannot be used for specific classifications, flag it as
         * permanently used
         */
        set_bit(0, priv->cfp.used);
        set_bit(0, priv->cfp.unique);

        /* Balance of_node_put() done by of_find_node_by_name() */
        of_node_get(dn);
        ports = of_find_node_by_name(dn, "ports");
        if (ports) {
                bcm_sf2_identify_ports(priv, ports);
                of_node_put(ports);
        }

        priv->irq0 = irq_of_parse_and_map(dn, 0);
        priv->irq1 = irq_of_parse_and_map(dn, 1);

        base = &priv->core;
        for (i = 0; i < BCM_SF2_REGS_NUM; i++) {
                *base = devm_platform_ioremap_resource(pdev, i);
                if (IS_ERR(*base)) {
                        pr_err("unable to find register: %s\n", reg_names[i]);
                        return PTR_ERR(*base);
                }
                base++;
        }

        priv->clk = devm_clk_get_optional(&pdev->dev, "sw_switch");
        if (IS_ERR(priv->clk))
                return PTR_ERR(priv->clk);

        clk_prepare_enable(priv->clk);

        priv->clk_mdiv = devm_clk_get_optional(&pdev->dev, "sw_switch_mdiv");
        if (IS_ERR(priv->clk_mdiv)) {
                ret = PTR_ERR(priv->clk_mdiv);
                goto out_clk;
        }

        clk_prepare_enable(priv->clk_mdiv);

        ret = bcm_sf2_sw_rst(priv);
        if (ret) {
                pr_err("unable to software reset switch: %d\n", ret);
                goto out_clk_mdiv;
        }

        bcm_sf2_crossbar_setup(priv);

        bcm_sf2_gphy_enable_set(priv->dev->ds, true);

        ret = bcm_sf2_mdio_register(ds);
        if (ret) {
                pr_err("failed to register MDIO bus\n");
                goto out_clk_mdiv;
        }

        bcm_sf2_gphy_enable_set(priv->dev->ds, false);

        ret = bcm_sf2_cfp_rst(priv);
        if (ret) {
                pr_err("failed to reset CFP\n");
                goto out_mdio;
        }

        /* Disable all interrupts and request them */
        bcm_sf2_intr_disable(priv);

        ret = devm_request_irq(&pdev->dev, priv->irq0, bcm_sf2_switch_0_isr, 0,
                               "switch_0", ds);
        if (ret < 0) {
                pr_err("failed to request switch_0 IRQ\n");
                goto out_mdio;
        }

        ret = devm_request_irq(&pdev->dev, priv->irq1, bcm_sf2_switch_1_isr, 0,
                               "switch_1", ds);
        if (ret < 0) {
                pr_err("failed to request switch_1 IRQ\n");
                goto out_mdio;
        }

        /* Reset the MIB counters */
        reg = core_readl(priv, CORE_GMNCFGCFG);
        reg |= RST_MIB_CNT;
        core_writel(priv, reg, CORE_GMNCFGCFG);
        reg &= ~RST_MIB_CNT;
        core_writel(priv, reg, CORE_GMNCFGCFG);

        /* Get the maximum number of ports for this switch */
        priv->hw_params.num_ports = core_readl(priv, CORE_IMP0_PRT_ID) + 1;
        if (priv->hw_params.num_ports > DSA_MAX_PORTS)
                priv->hw_params.num_ports = DSA_MAX_PORTS;

        /* Assume a single GPHY setup if we can't read that property */
        if (of_property_read_u32(dn, "brcm,num-gphy",
                                 &priv->hw_params.num_gphy))
                priv->hw_params.num_gphy = 1;

        rev = reg_readl(priv, REG_SWITCH_REVISION);
        priv->hw_params.top_rev = (rev >> SWITCH_TOP_REV_SHIFT) &
                                        SWITCH_TOP_REV_MASK;
        priv->hw_params.core_rev = (rev & SF2_REV_MASK);

        rev = reg_readl(priv, REG_PHY_REVISION);
        priv->hw_params.gphy_rev = rev & PHY_REVISION_MASK;

        ret = b53_switch_register(dev);
        if (ret)
                goto out_mdio;

        dev_info(&pdev->dev,
                 "Starfighter 2 top: %x.%02x, core: %x.%02x, IRQs: %d, %d\n",
                 priv->hw_params.top_rev >> 8, priv->hw_params.top_rev & 0xff,
                 priv->hw_params.core_rev >> 8, priv->hw_params.core_rev & 0xff,
                 priv->irq0, priv->irq1);

        return 0;

out_mdio:
        bcm_sf2_mdio_unregister(priv);
out_clk_mdiv:
        clk_disable_unprepare(priv->clk_mdiv);
out_clk:
        clk_disable_unprepare(priv->clk);
        return ret;
}

static int bcm_sf2_sw_remove(struct platform_device *pdev)
{
        struct bcm_sf2_priv *priv = platform_get_drvdata(pdev);

        if (!priv)
                return 0;

        priv->wol_ports_mask = 0;
        /* Disable interrupts */
        bcm_sf2_intr_disable(priv);
        dsa_unregister_switch(priv->dev->ds);
        bcm_sf2_cfp_exit(priv->dev->ds);
        bcm_sf2_mdio_unregister(priv);
        clk_disable_unprepare(priv->clk_mdiv);
        clk_disable_unprepare(priv->clk);
        if (priv->type == BCM7278_DEVICE_ID)
                reset_control_assert(priv->rcdev);

        platform_set_drvdata(pdev, NULL);

        return 0;
}

static void bcm_sf2_sw_shutdown(struct platform_device *pdev)
{
        struct bcm_sf2_priv *priv = platform_get_drvdata(pdev);

        if (!priv)
                return;

        /* For a kernel about to be kexec'd we want to keep the GPHY on for a
         * successful MDIO bus scan to occur. If we did turn off the GPHY
         * before (e.g: port_disable), this will also power it back on.
         *
         * Do not rely on kexec_in_progress, just power the PHY on.
         */
        if (priv->hw_params.num_gphy == 1)
                bcm_sf2_gphy_enable_set(priv->dev->ds, true);

        dsa_switch_shutdown(priv->dev->ds);

        platform_set_drvdata(pdev, NULL);
}

#ifdef CONFIG_PM_SLEEP
static int bcm_sf2_suspend(struct device *dev)
{
        struct bcm_sf2_priv *priv = dev_get_drvdata(dev);

        return dsa_switch_suspend(priv->dev->ds);
}

static int bcm_sf2_resume(struct device *dev)
{
        struct bcm_sf2_priv *priv = dev_get_drvdata(dev);

        return dsa_switch_resume(priv->dev->ds);
}
#endif /* CONFIG_PM_SLEEP */

static SIMPLE_DEV_PM_OPS(bcm_sf2_pm_ops,
                         bcm_sf2_suspend, bcm_sf2_resume);


static struct platform_driver bcm_sf2_driver = {
        .probe  = bcm_sf2_sw_probe,
        .remove = bcm_sf2_sw_remove,
        .shutdown = bcm_sf2_sw_shutdown,
        .driver = {
                .name = "brcm-sf2",
                .of_match_table = bcm_sf2_of_match,
                .pm = &bcm_sf2_pm_ops,
        },
};
module_platform_driver(bcm_sf2_driver);

MODULE_AUTHOR("Broadcom Corporation");
MODULE_DESCRIPTION("Driver for Broadcom Starfighter 2 ethernet switch chip");
MODULE_LICENSE("GPL");
MODULE_ALIAS("platform:brcm-sf2");