1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16#include <linux/kernel.h>
17#include <linux/module.h>
18#include <linux/types.h>
19#include <linux/pci.h>
20#include <linux/interrupt.h>
21
22#include "shpchp.h"
23
24
25#define SLOT_33MHZ 0x0000001f
26#define SLOT_66MHZ_PCIX 0x00001f00
27#define SLOT_100MHZ_PCIX 0x001f0000
28#define SLOT_133MHZ_PCIX 0x1f000000
29
30
31#define SLOT_66MHZ 0x0000001f
32#define SLOT_66MHZ_PCIX_266 0x00000f00
33#define SLOT_100MHZ_PCIX_266 0x0000f000
34#define SLOT_133MHZ_PCIX_266 0x000f0000
35#define SLOT_66MHZ_PCIX_533 0x00f00000
36#define SLOT_100MHZ_PCIX_533 0x0f000000
37#define SLOT_133MHZ_PCIX_533 0xf0000000
38
39
40#define SLOT_NUM 0x0000001F
41#define FIRST_DEV_NUM 0x00001F00
42#define PSN 0x07FF0000
43#define UPDOWN 0x20000000
44#define MRLSENSOR 0x40000000
45#define ATTN_BUTTON 0x80000000
46
47
48
49
50#define CMD_INTR_PENDING (1 << 0)
51#define SLOT_INTR_PENDING(i) (1 << (i + 1))
52
53
54
55
56#define GLOBAL_INTR_MASK (1 << 0)
57#define GLOBAL_SERR_MASK (1 << 1)
58#define COMMAND_INTR_MASK (1 << 2)
59#define ARBITER_SERR_MASK (1 << 3)
60#define COMMAND_DETECTED (1 << 16)
61#define ARBITER_DETECTED (1 << 17)
62#define SERR_INTR_RSVDZ_MASK 0xfffc0000
63
64
65
66
67#define SLOT_REG(i) (SLOT1 + (4 * i))
68
69#define SLOT_STATE_SHIFT (0)
70#define SLOT_STATE_MASK (3 << 0)
71#define SLOT_STATE_PWRONLY (1)
72#define SLOT_STATE_ENABLED (2)
73#define SLOT_STATE_DISABLED (3)
74#define PWR_LED_STATE_SHIFT (2)
75#define PWR_LED_STATE_MASK (3 << 2)
76#define ATN_LED_STATE_SHIFT (4)
77#define ATN_LED_STATE_MASK (3 << 4)
78#define ATN_LED_STATE_ON (1)
79#define ATN_LED_STATE_BLINK (2)
80#define ATN_LED_STATE_OFF (3)
81#define POWER_FAULT (1 << 6)
82#define ATN_BUTTON (1 << 7)
83#define MRL_SENSOR (1 << 8)
84#define MHZ66_CAP (1 << 9)
85#define PRSNT_SHIFT (10)
86#define PRSNT_MASK (3 << 10)
87#define PCIX_CAP_SHIFT (12)
88#define PCIX_CAP_MASK_PI1 (3 << 12)
89#define PCIX_CAP_MASK_PI2 (7 << 12)
90#define PRSNT_CHANGE_DETECTED (1 << 16)
91#define ISO_PFAULT_DETECTED (1 << 17)
92#define BUTTON_PRESS_DETECTED (1 << 18)
93#define MRL_CHANGE_DETECTED (1 << 19)
94#define CON_PFAULT_DETECTED (1 << 20)
95#define PRSNT_CHANGE_INTR_MASK (1 << 24)
96#define ISO_PFAULT_INTR_MASK (1 << 25)
97#define BUTTON_PRESS_INTR_MASK (1 << 26)
98#define MRL_CHANGE_INTR_MASK (1 << 27)
99#define CON_PFAULT_INTR_MASK (1 << 28)
100#define MRL_CHANGE_SERR_MASK (1 << 29)
101#define CON_PFAULT_SERR_MASK (1 << 30)
102#define SLOT_REG_RSVDZ_MASK ((1 << 15) | (7 << 21))
103
104
105
106
107
108
109
110
111
112
113
114
115#define SET_SLOT_PWR 0x01
116#define SET_SLOT_ENABLE 0x02
117#define SET_SLOT_DISABLE 0x03
118#define SET_PWR_ON 0x04
119#define SET_PWR_BLINK 0x08
120#define SET_PWR_OFF 0x0c
121#define SET_ATTN_ON 0x10
122#define SET_ATTN_BLINK 0x20
123#define SET_ATTN_OFF 0x30
124#define SETA_PCI_33MHZ 0x40
125#define SETA_PCI_66MHZ 0x41
126#define SETA_PCIX_66MHZ 0x42
127#define SETA_PCIX_100MHZ 0x43
128#define SETA_PCIX_133MHZ 0x44
129#define SETA_RESERVED1 0x45
130#define SETA_RESERVED2 0x46
131#define SETA_RESERVED3 0x47
132#define SET_PWR_ONLY_ALL 0x48
133#define SET_ENABLE_ALL 0x49
134#define SETB_PCI_33MHZ 0x50
135#define SETB_PCI_66MHZ 0x51
136#define SETB_PCIX_66MHZ_PM 0x52
137#define SETB_PCIX_100MHZ_PM 0x53
138#define SETB_PCIX_133MHZ_PM 0x54
139#define SETB_PCIX_66MHZ_EM 0x55
140#define SETB_PCIX_100MHZ_EM 0x56
141#define SETB_PCIX_133MHZ_EM 0x57
142#define SETB_PCIX_66MHZ_266 0x58
143#define SETB_PCIX_100MHZ_266 0x59
144#define SETB_PCIX_133MHZ_266 0x5a
145#define SETB_PCIX_66MHZ_533 0x5b
146#define SETB_PCIX_100MHZ_533 0x5c
147#define SETB_PCIX_133MHZ_533 0x5d
148#define SETB_RESERVED1 0x5e
149#define SETB_RESERVED2 0x5f
150
151
152
153
154#define SWITCH_OPEN 0x1
155#define INVALID_CMD 0x2
156#define INVALID_SPEED_MODE 0x4
157
158
159
160
161#define DWORD_SELECT 0x2
162#define DWORD_DATA 0x4
163
164
165#define SLOT_EVENT_LATCH 0x2
166#define SLOT_SERR_INT_MASK 0x3
167
168static irqreturn_t shpc_isr(int irq, void *dev_id);
169static void start_int_poll_timer(struct controller *ctrl, int sec);
170static int hpc_check_cmd_status(struct controller *ctrl);
171
172static inline u8 shpc_readb(struct controller *ctrl, int reg)
173{
174 return readb(ctrl->creg + reg);
175}
176
177static inline u16 shpc_readw(struct controller *ctrl, int reg)
178{
179 return readw(ctrl->creg + reg);
180}
181
182static inline void shpc_writew(struct controller *ctrl, int reg, u16 val)
183{
184 writew(val, ctrl->creg + reg);
185}
186
187static inline u32 shpc_readl(struct controller *ctrl, int reg)
188{
189 return readl(ctrl->creg + reg);
190}
191
192static inline void shpc_writel(struct controller *ctrl, int reg, u32 val)
193{
194 writel(val, ctrl->creg + reg);
195}
196
197static inline int shpc_indirect_read(struct controller *ctrl, int index,
198 u32 *value)
199{
200 int rc;
201 u32 cap_offset = ctrl->cap_offset;
202 struct pci_dev *pdev = ctrl->pci_dev;
203
204 rc = pci_write_config_byte(pdev, cap_offset + DWORD_SELECT, index);
205 if (rc)
206 return rc;
207 return pci_read_config_dword(pdev, cap_offset + DWORD_DATA, value);
208}
209
210
211
212
213static void int_poll_timeout(struct timer_list *t)
214{
215 struct controller *ctrl = from_timer(ctrl, t, poll_timer);
216
217
218 shpc_isr(0, ctrl);
219
220 if (!shpchp_poll_time)
221 shpchp_poll_time = 2;
222
223 start_int_poll_timer(ctrl, shpchp_poll_time);
224}
225
226
227
228
229static void start_int_poll_timer(struct controller *ctrl, int sec)
230{
231
232 if ((sec <= 0) || (sec > 60))
233 sec = 2;
234
235 ctrl->poll_timer.expires = jiffies + sec * HZ;
236 add_timer(&ctrl->poll_timer);
237}
238
239static inline int is_ctrl_busy(struct controller *ctrl)
240{
241 u16 cmd_status = shpc_readw(ctrl, CMD_STATUS);
242 return cmd_status & 0x1;
243}
244
245
246
247
248
249static inline int shpc_poll_ctrl_busy(struct controller *ctrl)
250{
251 int i;
252
253 if (!is_ctrl_busy(ctrl))
254 return 1;
255
256
257 for (i = 0; i < 10; i++) {
258 msleep(100);
259 if (!is_ctrl_busy(ctrl))
260 return 1;
261 }
262
263 return 0;
264}
265
266static inline int shpc_wait_cmd(struct controller *ctrl)
267{
268 int retval = 0;
269 unsigned long timeout = msecs_to_jiffies(1000);
270 int rc;
271
272 if (shpchp_poll_mode)
273 rc = shpc_poll_ctrl_busy(ctrl);
274 else
275 rc = wait_event_interruptible_timeout(ctrl->queue,
276 !is_ctrl_busy(ctrl), timeout);
277 if (!rc && is_ctrl_busy(ctrl)) {
278 retval = -EIO;
279 ctrl_err(ctrl, "Command not completed in 1000 msec\n");
280 } else if (rc < 0) {
281 retval = -EINTR;
282 ctrl_info(ctrl, "Command was interrupted by a signal\n");
283 }
284
285 return retval;
286}
287
288static int shpc_write_cmd(struct slot *slot, u8 t_slot, u8 cmd)
289{
290 struct controller *ctrl = slot->ctrl;
291 u16 cmd_status;
292 int retval = 0;
293 u16 temp_word;
294
295 mutex_lock(&slot->ctrl->cmd_lock);
296
297 if (!shpc_poll_ctrl_busy(ctrl)) {
298
299 ctrl_err(ctrl, "Controller is still busy after 1 sec\n");
300 retval = -EBUSY;
301 goto out;
302 }
303
304 ++t_slot;
305 temp_word = (t_slot << 8) | (cmd & 0xFF);
306 ctrl_dbg(ctrl, "%s: t_slot %x cmd %x\n", __func__, t_slot, cmd);
307
308
309
310
311 shpc_writew(ctrl, CMD, temp_word);
312
313
314
315
316 retval = shpc_wait_cmd(slot->ctrl);
317 if (retval)
318 goto out;
319
320 cmd_status = hpc_check_cmd_status(slot->ctrl);
321 if (cmd_status) {
322 ctrl_err(ctrl, "Failed to issued command 0x%x (error code = %d)\n",
323 cmd, cmd_status);
324 retval = -EIO;
325 }
326 out:
327 mutex_unlock(&slot->ctrl->cmd_lock);
328 return retval;
329}
330
331static int hpc_check_cmd_status(struct controller *ctrl)
332{
333 int retval = 0;
334 u16 cmd_status = shpc_readw(ctrl, CMD_STATUS) & 0x000F;
335
336 switch (cmd_status >> 1) {
337 case 0:
338 retval = 0;
339 break;
340 case 1:
341 retval = SWITCH_OPEN;
342 ctrl_err(ctrl, "Switch opened!\n");
343 break;
344 case 2:
345 retval = INVALID_CMD;
346 ctrl_err(ctrl, "Invalid HPC command!\n");
347 break;
348 case 4:
349 retval = INVALID_SPEED_MODE;
350 ctrl_err(ctrl, "Invalid bus speed/mode!\n");
351 break;
352 default:
353 retval = cmd_status;
354 }
355
356 return retval;
357}
358
359
360static int hpc_get_attention_status(struct slot *slot, u8 *status)
361{
362 struct controller *ctrl = slot->ctrl;
363 u32 slot_reg = shpc_readl(ctrl, SLOT_REG(slot->hp_slot));
364 u8 state = (slot_reg & ATN_LED_STATE_MASK) >> ATN_LED_STATE_SHIFT;
365
366 switch (state) {
367 case ATN_LED_STATE_ON:
368 *status = 1;
369 break;
370 case ATN_LED_STATE_BLINK:
371 *status = 2;
372 break;
373 case ATN_LED_STATE_OFF:
374 *status = 0;
375 break;
376 default:
377 *status = 0xFF;
378 break;
379 }
380
381 return 0;
382}
383
384static int hpc_get_power_status(struct slot *slot, u8 *status)
385{
386 struct controller *ctrl = slot->ctrl;
387 u32 slot_reg = shpc_readl(ctrl, SLOT_REG(slot->hp_slot));
388 u8 state = (slot_reg & SLOT_STATE_MASK) >> SLOT_STATE_SHIFT;
389
390 switch (state) {
391 case SLOT_STATE_PWRONLY:
392 *status = 2;
393 break;
394 case SLOT_STATE_ENABLED:
395 *status = 1;
396 break;
397 case SLOT_STATE_DISABLED:
398 *status = 0;
399 break;
400 default:
401 *status = 0xFF;
402 break;
403 }
404
405 return 0;
406}
407
408
409static int hpc_get_latch_status(struct slot *slot, u8 *status)
410{
411 struct controller *ctrl = slot->ctrl;
412 u32 slot_reg = shpc_readl(ctrl, SLOT_REG(slot->hp_slot));
413
414 *status = !!(slot_reg & MRL_SENSOR);
415
416 return 0;
417}
418
419static int hpc_get_adapter_status(struct slot *slot, u8 *status)
420{
421 struct controller *ctrl = slot->ctrl;
422 u32 slot_reg = shpc_readl(ctrl, SLOT_REG(slot->hp_slot));
423 u8 state = (slot_reg & PRSNT_MASK) >> PRSNT_SHIFT;
424
425 *status = (state != 0x3) ? 1 : 0;
426
427 return 0;
428}
429
430static int hpc_get_prog_int(struct slot *slot, u8 *prog_int)
431{
432 struct controller *ctrl = slot->ctrl;
433
434 *prog_int = shpc_readb(ctrl, PROG_INTERFACE);
435
436 return 0;
437}
438
439static int hpc_get_adapter_speed(struct slot *slot, enum pci_bus_speed *value)
440{
441 int retval = 0;
442 struct controller *ctrl = slot->ctrl;
443 u32 slot_reg = shpc_readl(ctrl, SLOT_REG(slot->hp_slot));
444 u8 m66_cap = !!(slot_reg & MHZ66_CAP);
445 u8 pi, pcix_cap;
446
447 retval = hpc_get_prog_int(slot, &pi);
448 if (retval)
449 return retval;
450
451 switch (pi) {
452 case 1:
453 pcix_cap = (slot_reg & PCIX_CAP_MASK_PI1) >> PCIX_CAP_SHIFT;
454 break;
455 case 2:
456 pcix_cap = (slot_reg & PCIX_CAP_MASK_PI2) >> PCIX_CAP_SHIFT;
457 break;
458 default:
459 return -ENODEV;
460 }
461
462 ctrl_dbg(ctrl, "%s: slot_reg = %x, pcix_cap = %x, m66_cap = %x\n",
463 __func__, slot_reg, pcix_cap, m66_cap);
464
465 switch (pcix_cap) {
466 case 0x0:
467 *value = m66_cap ? PCI_SPEED_66MHz : PCI_SPEED_33MHz;
468 break;
469 case 0x1:
470 *value = PCI_SPEED_66MHz_PCIX;
471 break;
472 case 0x3:
473 *value = PCI_SPEED_133MHz_PCIX;
474 break;
475 case 0x4:
476 *value = PCI_SPEED_133MHz_PCIX_266;
477 break;
478 case 0x5:
479 *value = PCI_SPEED_133MHz_PCIX_533;
480 break;
481 case 0x2:
482 default:
483 *value = PCI_SPEED_UNKNOWN;
484 retval = -ENODEV;
485 break;
486 }
487
488 ctrl_dbg(ctrl, "Adapter speed = %d\n", *value);
489 return retval;
490}
491
492static int hpc_get_mode1_ECC_cap(struct slot *slot, u8 *mode)
493{
494 int retval = 0;
495 struct controller *ctrl = slot->ctrl;
496 u16 sec_bus_status = shpc_readw(ctrl, SEC_BUS_CONFIG);
497 u8 pi = shpc_readb(ctrl, PROG_INTERFACE);
498
499 if (pi == 2) {
500 *mode = (sec_bus_status & 0x0100) >> 8;
501 } else {
502 retval = -1;
503 }
504
505 ctrl_dbg(ctrl, "Mode 1 ECC cap = %d\n", *mode);
506 return retval;
507}
508
509static int hpc_query_power_fault(struct slot *slot)
510{
511 struct controller *ctrl = slot->ctrl;
512 u32 slot_reg = shpc_readl(ctrl, SLOT_REG(slot->hp_slot));
513
514
515 return !(slot_reg & POWER_FAULT);
516}
517
518static int hpc_set_attention_status(struct slot *slot, u8 value)
519{
520 u8 slot_cmd = 0;
521
522 switch (value) {
523 case 0:
524 slot_cmd = SET_ATTN_OFF;
525 break;
526 case 1:
527 slot_cmd = SET_ATTN_ON;
528 break;
529 case 2:
530 slot_cmd = SET_ATTN_BLINK;
531 break;
532 default:
533 return -1;
534 }
535
536 return shpc_write_cmd(slot, slot->hp_slot, slot_cmd);
537}
538
539
540static void hpc_set_green_led_on(struct slot *slot)
541{
542 shpc_write_cmd(slot, slot->hp_slot, SET_PWR_ON);
543}
544
545static void hpc_set_green_led_off(struct slot *slot)
546{
547 shpc_write_cmd(slot, slot->hp_slot, SET_PWR_OFF);
548}
549
550static void hpc_set_green_led_blink(struct slot *slot)
551{
552 shpc_write_cmd(slot, slot->hp_slot, SET_PWR_BLINK);
553}
554
555static void hpc_release_ctlr(struct controller *ctrl)
556{
557 int i;
558 u32 slot_reg, serr_int;
559
560
561
562
563 for (i = 0; i < ctrl->num_slots; i++) {
564 slot_reg = shpc_readl(ctrl, SLOT_REG(i));
565 slot_reg |= (PRSNT_CHANGE_INTR_MASK | ISO_PFAULT_INTR_MASK |
566 BUTTON_PRESS_INTR_MASK | MRL_CHANGE_INTR_MASK |
567 CON_PFAULT_INTR_MASK | MRL_CHANGE_SERR_MASK |
568 CON_PFAULT_SERR_MASK);
569 slot_reg &= ~SLOT_REG_RSVDZ_MASK;
570 shpc_writel(ctrl, SLOT_REG(i), slot_reg);
571 }
572
573 cleanup_slots(ctrl);
574
575
576
577
578 serr_int = shpc_readl(ctrl, SERR_INTR_ENABLE);
579 serr_int |= (GLOBAL_INTR_MASK | GLOBAL_SERR_MASK |
580 COMMAND_INTR_MASK | ARBITER_SERR_MASK);
581 serr_int &= ~SERR_INTR_RSVDZ_MASK;
582 shpc_writel(ctrl, SERR_INTR_ENABLE, serr_int);
583
584 if (shpchp_poll_mode)
585 del_timer(&ctrl->poll_timer);
586 else {
587 free_irq(ctrl->pci_dev->irq, ctrl);
588 pci_disable_msi(ctrl->pci_dev);
589 }
590
591 iounmap(ctrl->creg);
592 release_mem_region(ctrl->mmio_base, ctrl->mmio_size);
593}
594
595static int hpc_power_on_slot(struct slot *slot)
596{
597 int retval;
598
599 retval = shpc_write_cmd(slot, slot->hp_slot, SET_SLOT_PWR);
600 if (retval)
601 ctrl_err(slot->ctrl, "%s: Write command failed!\n", __func__);
602
603 return retval;
604}
605
606static int hpc_slot_enable(struct slot *slot)
607{
608 int retval;
609
610
611 retval = shpc_write_cmd(slot, slot->hp_slot,
612 SET_SLOT_ENABLE | SET_PWR_BLINK | SET_ATTN_OFF);
613 if (retval)
614 ctrl_err(slot->ctrl, "%s: Write command failed!\n", __func__);
615
616 return retval;
617}
618
619static int hpc_slot_disable(struct slot *slot)
620{
621 int retval;
622
623
624 retval = shpc_write_cmd(slot, slot->hp_slot,
625 SET_SLOT_DISABLE | SET_PWR_OFF | SET_ATTN_ON);
626 if (retval)
627 ctrl_err(slot->ctrl, "%s: Write command failed!\n", __func__);
628
629 return retval;
630}
631
632static int shpc_get_cur_bus_speed(struct controller *ctrl)
633{
634 int retval = 0;
635 struct pci_bus *bus = ctrl->pci_dev->subordinate;
636 enum pci_bus_speed bus_speed = PCI_SPEED_UNKNOWN;
637 u16 sec_bus_reg = shpc_readw(ctrl, SEC_BUS_CONFIG);
638 u8 pi = shpc_readb(ctrl, PROG_INTERFACE);
639 u8 speed_mode = (pi == 2) ? (sec_bus_reg & 0xF) : (sec_bus_reg & 0x7);
640
641 if ((pi == 1) && (speed_mode > 4)) {
642 retval = -ENODEV;
643 goto out;
644 }
645
646 switch (speed_mode) {
647 case 0x0:
648 bus_speed = PCI_SPEED_33MHz;
649 break;
650 case 0x1:
651 bus_speed = PCI_SPEED_66MHz;
652 break;
653 case 0x2:
654 bus_speed = PCI_SPEED_66MHz_PCIX;
655 break;
656 case 0x3:
657 bus_speed = PCI_SPEED_100MHz_PCIX;
658 break;
659 case 0x4:
660 bus_speed = PCI_SPEED_133MHz_PCIX;
661 break;
662 case 0x5:
663 bus_speed = PCI_SPEED_66MHz_PCIX_ECC;
664 break;
665 case 0x6:
666 bus_speed = PCI_SPEED_100MHz_PCIX_ECC;
667 break;
668 case 0x7:
669 bus_speed = PCI_SPEED_133MHz_PCIX_ECC;
670 break;
671 case 0x8:
672 bus_speed = PCI_SPEED_66MHz_PCIX_266;
673 break;
674 case 0x9:
675 bus_speed = PCI_SPEED_100MHz_PCIX_266;
676 break;
677 case 0xa:
678 bus_speed = PCI_SPEED_133MHz_PCIX_266;
679 break;
680 case 0xb:
681 bus_speed = PCI_SPEED_66MHz_PCIX_533;
682 break;
683 case 0xc:
684 bus_speed = PCI_SPEED_100MHz_PCIX_533;
685 break;
686 case 0xd:
687 bus_speed = PCI_SPEED_133MHz_PCIX_533;
688 break;
689 default:
690 retval = -ENODEV;
691 break;
692 }
693
694 out:
695 bus->cur_bus_speed = bus_speed;
696 dbg("Current bus speed = %d\n", bus_speed);
697 return retval;
698}
699
700
701static int hpc_set_bus_speed_mode(struct slot *slot, enum pci_bus_speed value)
702{
703 int retval;
704 struct controller *ctrl = slot->ctrl;
705 u8 pi, cmd;
706
707 pi = shpc_readb(ctrl, PROG_INTERFACE);
708 if ((pi == 1) && (value > PCI_SPEED_133MHz_PCIX))
709 return -EINVAL;
710
711 switch (value) {
712 case PCI_SPEED_33MHz:
713 cmd = SETA_PCI_33MHZ;
714 break;
715 case PCI_SPEED_66MHz:
716 cmd = SETA_PCI_66MHZ;
717 break;
718 case PCI_SPEED_66MHz_PCIX:
719 cmd = SETA_PCIX_66MHZ;
720 break;
721 case PCI_SPEED_100MHz_PCIX:
722 cmd = SETA_PCIX_100MHZ;
723 break;
724 case PCI_SPEED_133MHz_PCIX:
725 cmd = SETA_PCIX_133MHZ;
726 break;
727 case PCI_SPEED_66MHz_PCIX_ECC:
728 cmd = SETB_PCIX_66MHZ_EM;
729 break;
730 case PCI_SPEED_100MHz_PCIX_ECC:
731 cmd = SETB_PCIX_100MHZ_EM;
732 break;
733 case PCI_SPEED_133MHz_PCIX_ECC:
734 cmd = SETB_PCIX_133MHZ_EM;
735 break;
736 case PCI_SPEED_66MHz_PCIX_266:
737 cmd = SETB_PCIX_66MHZ_266;
738 break;
739 case PCI_SPEED_100MHz_PCIX_266:
740 cmd = SETB_PCIX_100MHZ_266;
741 break;
742 case PCI_SPEED_133MHz_PCIX_266:
743 cmd = SETB_PCIX_133MHZ_266;
744 break;
745 case PCI_SPEED_66MHz_PCIX_533:
746 cmd = SETB_PCIX_66MHZ_533;
747 break;
748 case PCI_SPEED_100MHz_PCIX_533:
749 cmd = SETB_PCIX_100MHZ_533;
750 break;
751 case PCI_SPEED_133MHz_PCIX_533:
752 cmd = SETB_PCIX_133MHZ_533;
753 break;
754 default:
755 return -EINVAL;
756 }
757
758 retval = shpc_write_cmd(slot, 0, cmd);
759 if (retval)
760 ctrl_err(ctrl, "%s: Write command failed!\n", __func__);
761 else
762 shpc_get_cur_bus_speed(ctrl);
763
764 return retval;
765}
766
767static irqreturn_t shpc_isr(int irq, void *dev_id)
768{
769 struct controller *ctrl = (struct controller *)dev_id;
770 u32 serr_int, slot_reg, intr_loc, intr_loc2;
771 int hp_slot;
772
773
774 intr_loc = shpc_readl(ctrl, INTR_LOC);
775 if (!intr_loc)
776 return IRQ_NONE;
777
778 ctrl_dbg(ctrl, "%s: intr_loc = %x\n", __func__, intr_loc);
779
780 if (!shpchp_poll_mode) {
781
782
783
784
785 serr_int = shpc_readl(ctrl, SERR_INTR_ENABLE);
786 serr_int |= GLOBAL_INTR_MASK;
787 serr_int &= ~SERR_INTR_RSVDZ_MASK;
788 shpc_writel(ctrl, SERR_INTR_ENABLE, serr_int);
789
790 intr_loc2 = shpc_readl(ctrl, INTR_LOC);
791 ctrl_dbg(ctrl, "%s: intr_loc2 = %x\n", __func__, intr_loc2);
792 }
793
794 if (intr_loc & CMD_INTR_PENDING) {
795
796
797
798
799
800 serr_int = shpc_readl(ctrl, SERR_INTR_ENABLE);
801 serr_int &= ~SERR_INTR_RSVDZ_MASK;
802 shpc_writel(ctrl, SERR_INTR_ENABLE, serr_int);
803
804 wake_up_interruptible(&ctrl->queue);
805 }
806
807 if (!(intr_loc & ~CMD_INTR_PENDING))
808 goto out;
809
810 for (hp_slot = 0; hp_slot < ctrl->num_slots; hp_slot++) {
811
812 if (!(intr_loc & SLOT_INTR_PENDING(hp_slot)))
813 continue;
814
815 slot_reg = shpc_readl(ctrl, SLOT_REG(hp_slot));
816 ctrl_dbg(ctrl, "Slot %x with intr, slot register = %x\n",
817 hp_slot, slot_reg);
818
819 if (slot_reg & MRL_CHANGE_DETECTED)
820 shpchp_handle_switch_change(hp_slot, ctrl);
821
822 if (slot_reg & BUTTON_PRESS_DETECTED)
823 shpchp_handle_attention_button(hp_slot, ctrl);
824
825 if (slot_reg & PRSNT_CHANGE_DETECTED)
826 shpchp_handle_presence_change(hp_slot, ctrl);
827
828 if (slot_reg & (ISO_PFAULT_DETECTED | CON_PFAULT_DETECTED))
829 shpchp_handle_power_fault(hp_slot, ctrl);
830
831
832 slot_reg &= ~SLOT_REG_RSVDZ_MASK;
833 shpc_writel(ctrl, SLOT_REG(hp_slot), slot_reg);
834 }
835 out:
836 if (!shpchp_poll_mode) {
837
838 serr_int = shpc_readl(ctrl, SERR_INTR_ENABLE);
839 serr_int &= ~(GLOBAL_INTR_MASK | SERR_INTR_RSVDZ_MASK);
840 shpc_writel(ctrl, SERR_INTR_ENABLE, serr_int);
841 }
842
843 return IRQ_HANDLED;
844}
845
846static int shpc_get_max_bus_speed(struct controller *ctrl)
847{
848 int retval = 0;
849 struct pci_bus *bus = ctrl->pci_dev->subordinate;
850 enum pci_bus_speed bus_speed = PCI_SPEED_UNKNOWN;
851 u8 pi = shpc_readb(ctrl, PROG_INTERFACE);
852 u32 slot_avail1 = shpc_readl(ctrl, SLOT_AVAIL1);
853 u32 slot_avail2 = shpc_readl(ctrl, SLOT_AVAIL2);
854
855 if (pi == 2) {
856 if (slot_avail2 & SLOT_133MHZ_PCIX_533)
857 bus_speed = PCI_SPEED_133MHz_PCIX_533;
858 else if (slot_avail2 & SLOT_100MHZ_PCIX_533)
859 bus_speed = PCI_SPEED_100MHz_PCIX_533;
860 else if (slot_avail2 & SLOT_66MHZ_PCIX_533)
861 bus_speed = PCI_SPEED_66MHz_PCIX_533;
862 else if (slot_avail2 & SLOT_133MHZ_PCIX_266)
863 bus_speed = PCI_SPEED_133MHz_PCIX_266;
864 else if (slot_avail2 & SLOT_100MHZ_PCIX_266)
865 bus_speed = PCI_SPEED_100MHz_PCIX_266;
866 else if (slot_avail2 & SLOT_66MHZ_PCIX_266)
867 bus_speed = PCI_SPEED_66MHz_PCIX_266;
868 }
869
870 if (bus_speed == PCI_SPEED_UNKNOWN) {
871 if (slot_avail1 & SLOT_133MHZ_PCIX)
872 bus_speed = PCI_SPEED_133MHz_PCIX;
873 else if (slot_avail1 & SLOT_100MHZ_PCIX)
874 bus_speed = PCI_SPEED_100MHz_PCIX;
875 else if (slot_avail1 & SLOT_66MHZ_PCIX)
876 bus_speed = PCI_SPEED_66MHz_PCIX;
877 else if (slot_avail2 & SLOT_66MHZ)
878 bus_speed = PCI_SPEED_66MHz;
879 else if (slot_avail1 & SLOT_33MHZ)
880 bus_speed = PCI_SPEED_33MHz;
881 else
882 retval = -ENODEV;
883 }
884
885 bus->max_bus_speed = bus_speed;
886 ctrl_dbg(ctrl, "Max bus speed = %d\n", bus_speed);
887
888 return retval;
889}
890
891static const struct hpc_ops shpchp_hpc_ops = {
892 .power_on_slot = hpc_power_on_slot,
893 .slot_enable = hpc_slot_enable,
894 .slot_disable = hpc_slot_disable,
895 .set_bus_speed_mode = hpc_set_bus_speed_mode,
896 .set_attention_status = hpc_set_attention_status,
897 .get_power_status = hpc_get_power_status,
898 .get_attention_status = hpc_get_attention_status,
899 .get_latch_status = hpc_get_latch_status,
900 .get_adapter_status = hpc_get_adapter_status,
901
902 .get_adapter_speed = hpc_get_adapter_speed,
903 .get_mode1_ECC_cap = hpc_get_mode1_ECC_cap,
904 .get_prog_int = hpc_get_prog_int,
905
906 .query_power_fault = hpc_query_power_fault,
907 .green_led_on = hpc_set_green_led_on,
908 .green_led_off = hpc_set_green_led_off,
909 .green_led_blink = hpc_set_green_led_blink,
910
911 .release_ctlr = hpc_release_ctlr,
912};
913
914int shpc_init(struct controller *ctrl, struct pci_dev *pdev)
915{
916 int rc = -1, num_slots = 0;
917 u8 hp_slot;
918 u32 shpc_base_offset;
919 u32 tempdword, slot_reg, slot_config;
920 u8 i;
921
922 ctrl->pci_dev = pdev;
923 ctrl_dbg(ctrl, "Hotplug Controller:\n");
924
925 if (pdev->vendor == PCI_VENDOR_ID_AMD &&
926 pdev->device == PCI_DEVICE_ID_AMD_GOLAM_7450) {
927
928 ctrl->mmio_base = pci_resource_start(pdev, 0);
929 ctrl->mmio_size = pci_resource_len(pdev, 0);
930 } else {
931 ctrl->cap_offset = pci_find_capability(pdev, PCI_CAP_ID_SHPC);
932 if (!ctrl->cap_offset) {
933 ctrl_err(ctrl, "Cannot find PCI capability\n");
934 goto abort;
935 }
936 ctrl_dbg(ctrl, " cap_offset = %x\n", ctrl->cap_offset);
937
938 rc = shpc_indirect_read(ctrl, 0, &shpc_base_offset);
939 if (rc) {
940 ctrl_err(ctrl, "Cannot read base_offset\n");
941 goto abort;
942 }
943
944 rc = shpc_indirect_read(ctrl, 3, &tempdword);
945 if (rc) {
946 ctrl_err(ctrl, "Cannot read slot config\n");
947 goto abort;
948 }
949 num_slots = tempdword & SLOT_NUM;
950 ctrl_dbg(ctrl, " num_slots (indirect) %x\n", num_slots);
951
952 for (i = 0; i < 9 + num_slots; i++) {
953 rc = shpc_indirect_read(ctrl, i, &tempdword);
954 if (rc) {
955 ctrl_err(ctrl, "Cannot read creg (index = %d)\n",
956 i);
957 goto abort;
958 }
959 ctrl_dbg(ctrl, " offset %d: value %x\n", i, tempdword);
960 }
961
962 ctrl->mmio_base =
963 pci_resource_start(pdev, 0) + shpc_base_offset;
964 ctrl->mmio_size = 0x24 + 0x4 * num_slots;
965 }
966
967 ctrl_info(ctrl, "HPC vendor_id %x device_id %x ss_vid %x ss_did %x\n",
968 pdev->vendor, pdev->device, pdev->subsystem_vendor,
969 pdev->subsystem_device);
970
971 rc = pci_enable_device(pdev);
972 if (rc) {
973 ctrl_err(ctrl, "pci_enable_device failed\n");
974 goto abort;
975 }
976
977 if (!request_mem_region(ctrl->mmio_base, ctrl->mmio_size, MY_NAME)) {
978 ctrl_err(ctrl, "Cannot reserve MMIO region\n");
979 rc = -1;
980 goto abort;
981 }
982
983 ctrl->creg = ioremap(ctrl->mmio_base, ctrl->mmio_size);
984 if (!ctrl->creg) {
985 ctrl_err(ctrl, "Cannot remap MMIO region %lx @ %lx\n",
986 ctrl->mmio_size, ctrl->mmio_base);
987 release_mem_region(ctrl->mmio_base, ctrl->mmio_size);
988 rc = -1;
989 goto abort;
990 }
991 ctrl_dbg(ctrl, "ctrl->creg %p\n", ctrl->creg);
992
993 mutex_init(&ctrl->crit_sect);
994 mutex_init(&ctrl->cmd_lock);
995
996
997 init_waitqueue_head(&ctrl->queue);
998
999 ctrl->hpc_ops = &shpchp_hpc_ops;
1000
1001
1002 slot_config = shpc_readl(ctrl, SLOT_CONFIG);
1003 ctrl->slot_device_offset = (slot_config & FIRST_DEV_NUM) >> 8;
1004 ctrl->num_slots = slot_config & SLOT_NUM;
1005 ctrl->first_slot = (slot_config & PSN) >> 16;
1006 ctrl->slot_num_inc = ((slot_config & UPDOWN) >> 29) ? 1 : -1;
1007
1008
1009 tempdword = shpc_readl(ctrl, SERR_INTR_ENABLE);
1010 ctrl_dbg(ctrl, "SERR_INTR_ENABLE = %x\n", tempdword);
1011 tempdword |= (GLOBAL_INTR_MASK | GLOBAL_SERR_MASK |
1012 COMMAND_INTR_MASK | ARBITER_SERR_MASK);
1013 tempdword &= ~SERR_INTR_RSVDZ_MASK;
1014 shpc_writel(ctrl, SERR_INTR_ENABLE, tempdword);
1015 tempdword = shpc_readl(ctrl, SERR_INTR_ENABLE);
1016 ctrl_dbg(ctrl, "SERR_INTR_ENABLE = %x\n", tempdword);
1017
1018
1019
1020
1021 for (hp_slot = 0; hp_slot < ctrl->num_slots; hp_slot++) {
1022 slot_reg = shpc_readl(ctrl, SLOT_REG(hp_slot));
1023 ctrl_dbg(ctrl, "Default Logical Slot Register %d value %x\n",
1024 hp_slot, slot_reg);
1025 slot_reg |= (PRSNT_CHANGE_INTR_MASK | ISO_PFAULT_INTR_MASK |
1026 BUTTON_PRESS_INTR_MASK | MRL_CHANGE_INTR_MASK |
1027 CON_PFAULT_INTR_MASK | MRL_CHANGE_SERR_MASK |
1028 CON_PFAULT_SERR_MASK);
1029 slot_reg &= ~SLOT_REG_RSVDZ_MASK;
1030 shpc_writel(ctrl, SLOT_REG(hp_slot), slot_reg);
1031 }
1032
1033 if (shpchp_poll_mode) {
1034
1035 timer_setup(&ctrl->poll_timer, int_poll_timeout, 0);
1036 start_int_poll_timer(ctrl, 10);
1037 } else {
1038
1039 rc = pci_enable_msi(pdev);
1040 if (rc) {
1041 ctrl_info(ctrl, "Can't get msi for the hotplug controller\n");
1042 ctrl_info(ctrl, "Use INTx for the hotplug controller\n");
1043 } else {
1044 pci_set_master(pdev);
1045 }
1046
1047 rc = request_irq(ctrl->pci_dev->irq, shpc_isr, IRQF_SHARED,
1048 MY_NAME, (void *)ctrl);
1049 ctrl_dbg(ctrl, "request_irq %d (returns %d)\n",
1050 ctrl->pci_dev->irq, rc);
1051 if (rc) {
1052 ctrl_err(ctrl, "Can't get irq %d for the hotplug controller\n",
1053 ctrl->pci_dev->irq);
1054 goto abort_iounmap;
1055 }
1056 }
1057 ctrl_dbg(ctrl, "HPC at %s irq=%x\n", pci_name(pdev), pdev->irq);
1058
1059 shpc_get_max_bus_speed(ctrl);
1060 shpc_get_cur_bus_speed(ctrl);
1061
1062
1063
1064
1065 for (hp_slot = 0; hp_slot < ctrl->num_slots; hp_slot++) {
1066 slot_reg = shpc_readl(ctrl, SLOT_REG(hp_slot));
1067 ctrl_dbg(ctrl, "Default Logical Slot Register %d value %x\n",
1068 hp_slot, slot_reg);
1069 slot_reg &= ~(PRSNT_CHANGE_INTR_MASK | ISO_PFAULT_INTR_MASK |
1070 BUTTON_PRESS_INTR_MASK | MRL_CHANGE_INTR_MASK |
1071 CON_PFAULT_INTR_MASK | SLOT_REG_RSVDZ_MASK);
1072 shpc_writel(ctrl, SLOT_REG(hp_slot), slot_reg);
1073 }
1074 if (!shpchp_poll_mode) {
1075
1076 tempdword = shpc_readl(ctrl, SERR_INTR_ENABLE);
1077 tempdword &= ~(GLOBAL_INTR_MASK | COMMAND_INTR_MASK |
1078 SERR_INTR_RSVDZ_MASK);
1079 shpc_writel(ctrl, SERR_INTR_ENABLE, tempdword);
1080 tempdword = shpc_readl(ctrl, SERR_INTR_ENABLE);
1081 ctrl_dbg(ctrl, "SERR_INTR_ENABLE = %x\n", tempdword);
1082 }
1083
1084 return 0;
1085
1086
1087abort_iounmap:
1088 iounmap(ctrl->creg);
1089abort:
1090 return rc;
1091}
1092
