/* SPDX-License-Identifier: GPL-2.0-or-later */
/*
 *      Adaptec AAC series RAID controller driver
 *      (c) Copyright 2001 Red Hat Inc. <alan@redhat.com>
 *
 * based on the old aacraid driver that is..
 * Adaptec aacraid device driver for Linux.
 *
 * Copyright (c) 2000-2010 Adaptec, Inc.
 *               2010-2015 PMC-Sierra, Inc. (aacraid@pmc-sierra.com)
 *               2016-2017 Microsemi Corp. (aacraid@microsemi.com)
 *
 * Module Name:
 *  aacraid.h
 *
 * Abstract: Contains all routines for control of the aacraid driver
 */

#ifndef _AACRAID_H_
#define _AACRAID_H_
#ifndef dprintk
# define dprintk(x)
#endif
/* eg: if (nblank(dprintk(x))) */
#define _nblank(x) #x
#define nblank(x) _nblank(x)[0]

#include <linux/interrupt.h>
#include <linux/completion.h>
#include <linux/pci.h>
#include <scsi/scsi_host.h>

/*------------------------------------------------------------------------------
 *              D E F I N E S
 *----------------------------------------------------------------------------*/

#define AAC_MAX_MSIX            32      /* vectors */
#define AAC_PCI_MSI_ENABLE      0x8000

enum {
        AAC_ENABLE_INTERRUPT    = 0x0,
        AAC_DISABLE_INTERRUPT,
        AAC_ENABLE_MSIX,
        AAC_DISABLE_MSIX,
        AAC_CLEAR_AIF_BIT,
        AAC_CLEAR_SYNC_BIT,
        AAC_ENABLE_INTX
};

#define AAC_INT_MODE_INTX               (1<<0)
#define AAC_INT_MODE_MSI                (1<<1)
#define AAC_INT_MODE_AIF                (1<<2)
#define AAC_INT_MODE_SYNC               (1<<3)
#define AAC_INT_MODE_MSIX               (1<<16)

#define AAC_INT_ENABLE_TYPE1_INTX       0xfffffffb
#define AAC_INT_ENABLE_TYPE1_MSIX       0xfffffffa
#define AAC_INT_DISABLE_ALL             0xffffffff

/* Bit definitions in IOA->Host Interrupt Register */
#define PMC_TRANSITION_TO_OPERATIONAL   (1<<31)
#define PMC_IOARCB_TRANSFER_FAILED      (1<<28)
#define PMC_IOA_UNIT_CHECK              (1<<27)
#define PMC_NO_HOST_RRQ_FOR_CMD_RESPONSE (1<<26)
#define PMC_CRITICAL_IOA_OP_IN_PROGRESS (1<<25)
#define PMC_IOARRIN_LOST                (1<<4)
#define PMC_SYSTEM_BUS_MMIO_ERROR       (1<<3)
#define PMC_IOA_PROCESSOR_IN_ERROR_STATE (1<<2)
#define PMC_HOST_RRQ_VALID              (1<<1)
#define PMC_OPERATIONAL_STATUS          (1<<31)
#define PMC_ALLOW_MSIX_VECTOR0          (1<<0)

#define PMC_IOA_ERROR_INTERRUPTS        (PMC_IOARCB_TRANSFER_FAILED | \
                                         PMC_IOA_UNIT_CHECK | \
                                         PMC_NO_HOST_RRQ_FOR_CMD_RESPONSE | \
                                         PMC_IOARRIN_LOST | \
                                         PMC_SYSTEM_BUS_MMIO_ERROR | \
                                         PMC_IOA_PROCESSOR_IN_ERROR_STATE)

#define PMC_ALL_INTERRUPT_BITS          (PMC_IOA_ERROR_INTERRUPTS | \
                                         PMC_HOST_RRQ_VALID | \
                                         PMC_TRANSITION_TO_OPERATIONAL | \
                                         PMC_ALLOW_MSIX_VECTOR0)
#define PMC_GLOBAL_INT_BIT2             0x00000004
#define PMC_GLOBAL_INT_BIT0             0x00000001

#ifndef AAC_DRIVER_BUILD
# define AAC_DRIVER_BUILD 50983
# define AAC_DRIVER_BRANCH "-custom"
#endif
#define MAXIMUM_NUM_CONTAINERS  32

#define AAC_NUM_MGT_FIB         8
#define AAC_NUM_IO_FIB          (1024 - AAC_NUM_MGT_FIB)
#define AAC_NUM_FIB             (AAC_NUM_IO_FIB + AAC_NUM_MGT_FIB)

#define AAC_MAX_LUN             256

#define AAC_MAX_HOSTPHYSMEMPAGES (0xfffff)
#define AAC_MAX_32BIT_SGBCOUNT  ((unsigned short)256)

#define AAC_DEBUG_INSTRUMENT_AIF_DELETE

#define AAC_MAX_NATIVE_TARGETS          1024
/* Thor: 5 phys. buses: #0: empty, 1-4: 256 targets each */
#define AAC_MAX_BUSES                   5
#define AAC_MAX_TARGETS         256
#define AAC_BUS_TARGET_LOOP             (AAC_MAX_BUSES * AAC_MAX_TARGETS)
#define AAC_MAX_NATIVE_SIZE             2048
#define FW_ERROR_BUFFER_SIZE            512
#define AAC_SA_TIMEOUT                  180
#define AAC_ARC_TIMEOUT                 60

#define get_bus_number(x)       (x/AAC_MAX_TARGETS)
#define get_target_number(x)    (x%AAC_MAX_TARGETS)

/* Thor AIF events */
#define SA_AIF_HOTPLUG                  (1<<1)
#define SA_AIF_HARDWARE         (1<<2)
#define SA_AIF_PDEV_CHANGE              (1<<4)
#define SA_AIF_LDEV_CHANGE              (1<<5)
#define SA_AIF_BPSTAT_CHANGE            (1<<30)
#define SA_AIF_BPCFG_CHANGE             (1<<31)

#define HBA_MAX_SG_EMBEDDED             28
#define HBA_MAX_SG_SEPARATE             90
#define HBA_SENSE_DATA_LEN_MAX          32
#define HBA_REQUEST_TAG_ERROR_FLAG      0x00000002
#define HBA_SGL_FLAGS_EXT               0x80000000UL

struct aac_hba_sgl {
        u32             addr_lo; /* Lower 32-bits of SGL element address */
        u32             addr_hi; /* Upper 32-bits of SGL element address */
        u32             len;    /* Length of SGL element in bytes */
        u32             flags;  /* SGL element flags */
};

enum {
        HBA_IU_TYPE_SCSI_CMD_REQ                = 0x40,
        HBA_IU_TYPE_SCSI_TM_REQ                 = 0x41,
        HBA_IU_TYPE_SATA_REQ                    = 0x42,
        HBA_IU_TYPE_RESP                        = 0x60,
        HBA_IU_TYPE_COALESCED_RESP              = 0x61,
        HBA_IU_TYPE_INT_COALESCING_CFG_REQ      = 0x70
};

enum {
        HBA_CMD_BYTE1_DATA_DIR_IN               = 0x1,
        HBA_CMD_BYTE1_DATA_DIR_OUT              = 0x2,
        HBA_CMD_BYTE1_DATA_TYPE_DDR             = 0x4,
        HBA_CMD_BYTE1_CRYPTO_ENABLE             = 0x8
};

enum {
        HBA_CMD_BYTE1_BITOFF_DATA_DIR_IN        = 0x0,
        HBA_CMD_BYTE1_BITOFF_DATA_DIR_OUT,
        HBA_CMD_BYTE1_BITOFF_DATA_TYPE_DDR,
        HBA_CMD_BYTE1_BITOFF_CRYPTO_ENABLE
};

enum {
        HBA_RESP_DATAPRES_NO_DATA               = 0x0,
        HBA_RESP_DATAPRES_RESPONSE_DATA,
        HBA_RESP_DATAPRES_SENSE_DATA
};

enum {
        HBA_RESP_SVCRES_TASK_COMPLETE           = 0x0,
        HBA_RESP_SVCRES_FAILURE,
        HBA_RESP_SVCRES_TMF_COMPLETE,
        HBA_RESP_SVCRES_TMF_SUCCEEDED,
        HBA_RESP_SVCRES_TMF_REJECTED,
        HBA_RESP_SVCRES_TMF_LUN_INVALID
};

enum {
        HBA_RESP_STAT_IO_ERROR                  = 0x1,
        HBA_RESP_STAT_IO_ABORTED,
        HBA_RESP_STAT_NO_PATH_TO_DEVICE,
        HBA_RESP_STAT_INVALID_DEVICE,
        HBA_RESP_STAT_HBAMODE_DISABLED          = 0xE,
        HBA_RESP_STAT_UNDERRUN                  = 0x51,
        HBA_RESP_STAT_OVERRUN                   = 0x75
};

struct aac_hba_cmd_req {
        u8      iu_type;        /* HBA information unit type */
        /*
         * byte1:
         * [1:0] DIR - 0=No data, 0x1 = IN, 0x2 = OUT
         * [2]   TYPE - 0=PCI, 1=DDR
         * [3]   CRYPTO_ENABLE - 0=Crypto disabled, 1=Crypto enabled
         */
        u8      byte1;
        u8      reply_qid;      /* Host reply queue to post response to */
        u8      reserved1;
        __le32  it_nexus;       /* Device handle for the request */
        __le32  request_id;     /* Sender context */
        /* Lower 32-bits of tweak value for crypto enabled IOs */
        __le32  tweak_value_lo;
        u8      cdb[16];        /* SCSI CDB of the command */
        u8      lun[8];         /* SCSI LUN of the command */

        /* Total data length in bytes to be read/written (if any) */
        __le32  data_length;

        /* [2:0] Task Attribute, [6:3] Command Priority */
        u8      attr_prio;

        /* Number of SGL elements embedded in the HBA req */
        u8      emb_data_desc_count;

        __le16  dek_index;      /* DEK index for crypto enabled IOs */

        /* Lower 32-bits of reserved error data target location on the host */
        __le32  error_ptr_lo;

        /* Upper 32-bits of reserved error data target location on the host */
        __le32  error_ptr_hi;

        /* Length of reserved error data area on the host in bytes */
        __le32  error_length;

        /* Upper 32-bits of tweak value for crypto enabled IOs */
        __le32  tweak_value_hi;

        struct aac_hba_sgl sge[HBA_MAX_SG_SEPARATE+2]; /* SG list space */

        /*
         * structure must not exceed
         * AAC_MAX_NATIVE_SIZE-FW_ERROR_BUFFER_SIZE
         */
};

/* Task Management Functions (TMF) */
#define HBA_TMF_ABORT_TASK      0x01
#define HBA_TMF_LUN_RESET       0x08

struct aac_hba_tm_req {
        u8      iu_type;        /* HBA information unit type */
        u8      reply_qid;      /* Host reply queue to post response to */
        u8      tmf;            /* Task management function */
        u8      reserved1;

        __le32  it_nexus;       /* Device handle for the command */

        u8      lun[8];         /* SCSI LUN */

        /* Used to hold sender context. */
        __le32  request_id;     /* Sender context */
        __le32  reserved2;

        /* Request identifier of managed task */
        __le32  managed_request_id;     /* Sender context being managed */
        __le32  reserved3;

        /* Lower 32-bits of reserved error data target location on the host */
        __le32  error_ptr_lo;
        /* Upper 32-bits of reserved error data target location on the host */
        __le32  error_ptr_hi;
        /* Length of reserved error data area on the host in bytes */
        __le32  error_length;
};

struct aac_hba_reset_req {
        u8      iu_type;        /* HBA information unit type */
        /* 0 - reset specified device, 1 - reset all devices */
        u8      reset_type;
        u8      reply_qid;      /* Host reply queue to post response to */
        u8      reserved1;

        __le32  it_nexus;       /* Device handle for the command */
        __le32  request_id;     /* Sender context */
        /* Lower 32-bits of reserved error data target location on the host */
        __le32  error_ptr_lo;
        /* Upper 32-bits of reserved error data target location on the host */
        __le32  error_ptr_hi;
        /* Length of reserved error data area on the host in bytes */
        __le32  error_length;
};

struct aac_hba_resp {
        u8      iu_type;                /* HBA information unit type */
        u8      reserved1[3];
        __le32  request_identifier;     /* sender context */
        __le32  reserved2;
        u8      service_response;       /* SCSI service response */
        u8      status;                 /* SCSI status */
        u8      datapres;       /* [1:0] - data present, [7:2] - reserved */
        u8      sense_response_data_len;        /* Sense/response data length */
        __le32  residual_count;         /* Residual data length in bytes */
        /* Sense/response data */
        u8      sense_response_buf[HBA_SENSE_DATA_LEN_MAX];
};

struct aac_native_hba {
        union {
                struct aac_hba_cmd_req cmd;
                struct aac_hba_tm_req tmr;
                u8 cmd_bytes[AAC_MAX_NATIVE_SIZE-FW_ERROR_BUFFER_SIZE];
        } cmd;
        union {
                struct aac_hba_resp err;
                u8 resp_bytes[FW_ERROR_BUFFER_SIZE];
        } resp;
};

#define CISS_REPORT_PHYSICAL_LUNS       0xc3
#define WRITE_HOST_WELLNESS             0xa5
#define CISS_IDENTIFY_PHYSICAL_DEVICE   0x15
#define BMIC_IN                 0x26
#define BMIC_OUT                        0x27

struct aac_ciss_phys_luns_resp {
        u8      list_length[4];         /* LUN list length (N-7, big endian) */
        u8      resp_flag;              /* extended response_flag */
        u8      reserved[3];
        struct _ciss_lun {
                u8      tid[3];         /* Target ID */
                u8      bus;            /* Bus, flag (bits 6,7) */
                u8      level3[2];
                u8      level2[2];
                u8      node_ident[16]; /* phys. node identifier */
        } lun[1];                       /* List of phys. devices */
};

/*
 * Interrupts
 */
#define AAC_MAX_HRRQ            64

struct aac_ciss_identify_pd {
        u8 scsi_bus;                    /* SCSI Bus number on controller */
        u8 scsi_id;                     /* SCSI ID on this bus */
        u16 block_size;                 /* sector size in bytes */
        u32 total_blocks;               /* number for sectors on drive */
        u32 reserved_blocks;            /* controller reserved (RIS) */
        u8 model[40];                   /* Physical Drive Model */
        u8 serial_number[40];           /* Drive Serial Number */
        u8 firmware_revision[8];        /* drive firmware revision */
        u8 scsi_inquiry_bits;           /* inquiry byte 7 bits */
        u8 compaq_drive_stamp;          /* 0 means drive not stamped */
        u8 last_failure_reason;

        u8  flags;
        u8  more_flags;
        u8  scsi_lun;                   /* SCSI LUN for phys drive */
        u8  yet_more_flags;
        u8  even_more_flags;
        u32 spi_speed_rules;            /* SPI Speed :Ultra disable diagnose */
        u8  phys_connector[2];          /* connector number on controller */
        u8  phys_box_on_bus;            /* phys enclosure this drive resides */
        u8  phys_bay_in_box;            /* phys drv bay this drive resides */
        u32 rpm;                        /* Drive rotational speed in rpm */
        u8  device_type;                /* type of drive */
        u8  sata_version;               /* only valid when drive_type is SATA */
        u64 big_total_block_count;
        u64 ris_starting_lba;
        u32 ris_size;
        u8  wwid[20];
        u8  controller_phy_map[32];
        u16 phy_count;
        u8  phy_connected_dev_type[256];
        u8  phy_to_drive_bay_num[256];
        u16 phy_to_attached_dev_index[256];
        u8  box_index;
        u8  spitfire_support;
        u16 extra_physical_drive_flags;
        u8  negotiated_link_rate[256];
        u8  phy_to_phy_map[256];
        u8  redundant_path_present_map;
        u8  redundant_path_failure_map;
        u8  active_path_number;
        u16 alternate_paths_phys_connector[8];
        u8  alternate_paths_phys_box_on_port[8];
        u8  multi_lun_device_lun_count;
        u8  minimum_good_fw_revision[8];
        u8  unique_inquiry_bytes[20];
        u8  current_temperature_degreesC;
        u8  temperature_threshold_degreesC;
        u8  max_temperature_degreesC;
        u8  logical_blocks_per_phys_block_exp;  /* phyblocksize = 512 * 2^exp */
        u16 current_queue_depth_limit;
        u8  switch_name[10];
        u16 switch_port;
        u8  alternate_paths_switch_name[40];
        u8  alternate_paths_switch_port[8];
        u16 power_on_hours;             /* valid only if gas gauge supported */
        u16 percent_endurance_used;     /* valid only if gas gauge supported. */
        u8  drive_authentication;
        u8  smart_carrier_authentication;
        u8  smart_carrier_app_fw_version;
        u8  smart_carrier_bootloader_fw_version;
        u8  SanitizeSecureEraseSupport;
        u8  DriveKeyFlags;
        u8  encryption_key_name[64];
        u32 misc_drive_flags;
        u16 dek_index;
        u16 drive_encryption_flags;
        u8  sanitize_maximum_time[6];
        u8  connector_info_mode;
        u8  connector_info_number[4];
        u8  long_connector_name[64];
        u8  device_unique_identifier[16];
        u8  padto_2K[17];
} __packed;

/*
 * These macros convert from physical channels to virtual channels
 */
#define CONTAINER_CHANNEL               (0)
#define NATIVE_CHANNEL                  (1)
#define CONTAINER_TO_CHANNEL(cont)      (CONTAINER_CHANNEL)
#define CONTAINER_TO_ID(cont)           (cont)
#define CONTAINER_TO_LUN(cont)          (0)
#define ENCLOSURE_CHANNEL               (3)

#define PMC_DEVICE_S6   0x28b
#define PMC_DEVICE_S7   0x28c
#define PMC_DEVICE_S8   0x28d

#define aac_phys_to_logical(x)  ((x)+1)
#define aac_logical_to_phys(x)  ((x)?(x)-1:0)

/*
 * These macros are for keeping track of
 * character device state.
 */
#define AAC_CHARDEV_UNREGISTERED        (-1)
#define AAC_CHARDEV_NEEDS_REINIT        (-2)

/* #define AAC_DETAILED_STATUS_INFO */

struct diskparm
{
        int heads;
        int sectors;
        int cylinders;
};


/*
 *      Firmware constants
 */

#define         CT_NONE                 0
#define         CT_OK                   218
#define         FT_FILESYS      8       /* ADAPTEC's "FSA"(tm) filesystem */
#define         FT_DRIVE        9       /* physical disk - addressable in scsi by bus/id/lun */

/*
 *      Host side memory scatter gather list
 *      Used by the adapter for read, write, and readdirplus operations
 *      We have separate 32 and 64 bit version because even
 *      on 64 bit systems not all cards support the 64 bit version
 */
struct sgentry {
        __le32  addr;   /* 32-bit address. */
        __le32  count;  /* Length. */
};

struct user_sgentry {
        u32     addr;   /* 32-bit address. */
        u32     count;  /* Length. */
};

struct sgentry64 {
        __le32  addr[2];        /* 64-bit addr. 2 pieces for data alignment */
        __le32  count;  /* Length. */
};

struct user_sgentry64 {
        u32     addr[2];        /* 64-bit addr. 2 pieces for data alignment */
        u32     count;  /* Length. */
};

struct sgentryraw {
        __le32          next;   /* reserved for F/W use */
        __le32          prev;   /* reserved for F/W use */
        __le32          addr[2];
        __le32          count;
        __le32          flags;  /* reserved for F/W use */
};

struct user_sgentryraw {
        u32             next;   /* reserved for F/W use */
        u32             prev;   /* reserved for F/W use */
        u32             addr[2];
        u32             count;
        u32             flags;  /* reserved for F/W use */
};

struct sge_ieee1212 {
        u32     addrLow;
        u32     addrHigh;
        u32     length;
        u32     flags;
};

/*
 *      SGMAP
 *
 *      This is the SGMAP structure for all commands that use
 *      32-bit addressing.
 */

struct sgmap {
        __le32          count;
        struct sgentry  sg[1];
};

struct user_sgmap {
        u32             count;
        struct user_sgentry     sg[1];
};

struct sgmap64 {
        __le32          count;
        struct sgentry64 sg[1];
};

struct user_sgmap64 {
        u32             count;
        struct user_sgentry64 sg[1];
};

struct sgmapraw {
        __le32            count;
        struct sgentryraw sg[1];
};

struct user_sgmapraw {
        u32               count;
        struct user_sgentryraw sg[1];
};

struct creation_info
{
        u8              buildnum;               /* e.g., 588 */
        u8              usec;                   /* e.g., 588 */
        u8              via;                    /* e.g., 1 = FSU,
                                                 *       2 = API
                                                 */
        u8              year;                   /* e.g., 1997 = 97 */
        __le32          date;                   /*
                                                 * unsigned     Month           :4;     // 1 - 12
                                                 * unsigned     Day             :6;     // 1 - 32
                                                 * unsigned     Hour            :6;     // 0 - 23
                                                 * unsigned     Minute          :6;     // 0 - 60
                                                 * unsigned     Second          :6;     // 0 - 60
                                                 */
        __le32          serial[2];                      /* e.g., 0x1DEADB0BFAFAF001 */
};


/*
 *      Define all the constants needed for the communication interface
 */

/*
 *      Define how many queue entries each queue will have and the total
 *      number of entries for the entire communication interface. Also define
 *      how many queues we support.
 *
 *      This has to match the controller
 */

#define NUMBER_OF_COMM_QUEUES  8   // 4 command; 4 response
#define HOST_HIGH_CMD_ENTRIES  4
#define HOST_NORM_CMD_ENTRIES  8
#define ADAP_HIGH_CMD_ENTRIES  4
#define ADAP_NORM_CMD_ENTRIES  512
#define HOST_HIGH_RESP_ENTRIES 4
#define HOST_NORM_RESP_ENTRIES 512
#define ADAP_HIGH_RESP_ENTRIES 4
#define ADAP_NORM_RESP_ENTRIES 8

#define TOTAL_QUEUE_ENTRIES  \
    (HOST_NORM_CMD_ENTRIES + HOST_HIGH_CMD_ENTRIES + ADAP_NORM_CMD_ENTRIES + ADAP_HIGH_CMD_ENTRIES + \
            HOST_NORM_RESP_ENTRIES + HOST_HIGH_RESP_ENTRIES + ADAP_NORM_RESP_ENTRIES + ADAP_HIGH_RESP_ENTRIES)


/*
 *      Set the queues on a 16 byte alignment
 */

#define QUEUE_ALIGNMENT         16

/*
 *      The queue headers define the Communication Region queues. These
 *      are physically contiguous and accessible by both the adapter and the
 *      host. Even though all queue headers are in the same contiguous block
 *      they will be represented as individual units in the data structures.
 */

struct aac_entry {
        __le32 size; /* Size in bytes of Fib which this QE points to */
        __le32 addr; /* Receiver address of the FIB */
};

/*
 *      The adapter assumes the ProducerIndex and ConsumerIndex are grouped
 *      adjacently and in that order.
 */

struct aac_qhdr {
        __le64 header_addr;/* Address to hand the adapter to access
                              to this queue head */
        __le32 *producer; /* The producer index for this queue (host address) */
        __le32 *consumer; /* The consumer index for this queue (host address) */
};

/*
 *      Define all the events which the adapter would like to notify
 *      the host of.
 */

#define         HostNormCmdQue          1       /* Change in host normal priority command queue */
#define         HostHighCmdQue          2       /* Change in host high priority command queue */
#define         HostNormRespQue         3       /* Change in host normal priority response queue */
#define         HostHighRespQue         4       /* Change in host high priority response queue */
#define         AdapNormRespNotFull     5
#define         AdapHighRespNotFull     6
#define         AdapNormCmdNotFull      7
#define         AdapHighCmdNotFull      8
#define         SynchCommandComplete    9
#define         AdapInternalError       0xfe    /* The adapter detected an internal error shutting down */

/*
 *      Define all the events the host wishes to notify the
 *      adapter of. The first four values much match the Qid the
 *      corresponding queue.
 */

#define         AdapNormCmdQue          2
#define         AdapHighCmdQue          3
#define         AdapNormRespQue         6
#define         AdapHighRespQue         7
#define         HostShutdown            8
#define         HostPowerFail           9
#define         FatalCommError          10
#define         HostNormRespNotFull     11
#define         HostHighRespNotFull     12
#define         HostNormCmdNotFull      13
#define         HostHighCmdNotFull      14
#define         FastIo                  15
#define         AdapPrintfDone          16

/*
 *      Define all the queues that the adapter and host use to communicate
 *      Number them to match the physical queue layout.
 */

enum aac_queue_types {
        HostNormCmdQueue = 0,   /* Adapter to host normal priority command traffic */
        HostHighCmdQueue,       /* Adapter to host high priority command traffic */
        AdapNormCmdQueue,       /* Host to adapter normal priority command traffic */
        AdapHighCmdQueue,       /* Host to adapter high priority command traffic */
        HostNormRespQueue,      /* Adapter to host normal priority response traffic */
        HostHighRespQueue,      /* Adapter to host high priority response traffic */
        AdapNormRespQueue,      /* Host to adapter normal priority response traffic */
        AdapHighRespQueue       /* Host to adapter high priority response traffic */
};

/*
 *      Assign type values to the FSA communication data structures
 */

#define         FIB_MAGIC       0x0001
#define         FIB_MAGIC2      0x0004
#define         FIB_MAGIC2_64   0x0005

/*
 *      Define the priority levels the FSA communication routines support.
 */

#define         FsaNormal       1

/* transport FIB header (PMC) */
struct aac_fib_xporthdr {
        __le64  HostAddress;    /* FIB host address w/o xport header */
        __le32  Size;           /* FIB size excluding xport header */
        __le32  Handle;         /* driver handle to reference the FIB */
        __le64  Reserved[2];
};

#define         ALIGN32         32

/*
 * Define the FIB. The FIB is the where all the requested data and
 * command information are put to the application on the FSA adapter.
 */

struct aac_fibhdr {
        __le32 XferState;       /* Current transfer state for this CCB */
        __le16 Command;         /* Routing information for the destination */
        u8 StructType;          /* Type FIB */
        u8 Unused;              /* Unused */
        __le16 Size;            /* Size of this FIB in bytes */
        __le16 SenderSize;      /* Size of the FIB in the sender
                                   (for response sizing) */
        __le32 SenderFibAddress;  /* Host defined data in the FIB */
        union {
                __le32 ReceiverFibAddress;/* Logical address of this FIB for
                                     the adapter (old) */
                __le32 SenderFibAddressHigh;/* upper 32bit of phys. FIB address */
                __le32 TimeStamp;       /* otherwise timestamp for FW internal use */
        } u;
        __le32 Handle;          /* FIB handle used for MSGU commnunication */
        u32 Previous;           /* FW internal use */
        u32 Next;               /* FW internal use */
};

struct hw_fib {
        struct aac_fibhdr header;
        u8 data[512-sizeof(struct aac_fibhdr)]; // Command specific data
};

/*
 *      FIB commands
 */

#define         TestCommandResponse             1
#define         TestAdapterCommand              2
/*
 *      Lowlevel and comm commands
 */
#define         LastTestCommand                 100
#define         ReinitHostNormCommandQueue      101
#define         ReinitHostHighCommandQueue      102
#define         ReinitHostHighRespQueue         103
#define         ReinitHostNormRespQueue         104
#define         ReinitAdapNormCommandQueue      105
#define         ReinitAdapHighCommandQueue      107
#define         ReinitAdapHighRespQueue         108
#define         ReinitAdapNormRespQueue         109
#define         InterfaceShutdown               110
#define         DmaCommandFib                   120
#define         StartProfile                    121
#define         TermProfile                     122
#define         SpeedTest                       123
#define         TakeABreakPt                    124
#define         RequestPerfData                 125
#define         SetInterruptDefTimer            126
#define         SetInterruptDefCount            127
#define         GetInterruptDefStatus           128
#define         LastCommCommand                 129
/*
 *      Filesystem commands
 */
#define         NuFileSystem                    300
#define         UFS                             301
#define         HostFileSystem                  302
#define         LastFileSystemCommand           303
/*
 *      Container Commands
 */
#define         ContainerCommand                500
#define         ContainerCommand64              501
#define         ContainerRawIo                  502
#define         ContainerRawIo2                 503
/*
 *      Scsi Port commands (scsi passthrough)
 */
#define         ScsiPortCommand                 600
#define         ScsiPortCommand64               601
/*
 *      Misc house keeping and generic adapter initiated commands
 */
#define         AifRequest                      700
#define         CheckRevision                   701
#define         FsaHostShutdown                 702
#define         RequestAdapterInfo              703
#define         IsAdapterPaused                 704
#define         SendHostTime                    705
#define         RequestSupplementAdapterInfo    706
#define         LastMiscCommand                 707

/*
 * Commands that will target the failover level on the FSA adapter
 */

enum fib_xfer_state {
        HostOwned                       = (1<<0),
        AdapterOwned                    = (1<<1),
        FibInitialized                  = (1<<2),
        FibEmpty                        = (1<<3),
        AllocatedFromPool               = (1<<4),
        SentFromHost                    = (1<<5),
        SentFromAdapter                 = (1<<6),
        ResponseExpected                = (1<<7),
        NoResponseExpected              = (1<<8),
        AdapterProcessed                = (1<<9),
        HostProcessed                   = (1<<10),
        HighPriority                    = (1<<11),
        NormalPriority                  = (1<<12),
        Async                           = (1<<13),
        AsyncIo                         = (1<<13),      // rpbfix: remove with new regime
        PageFileIo                      = (1<<14),      // rpbfix: remove with new regime
        ShutdownRequest                 = (1<<15),
        LazyWrite                       = (1<<16),      // rpbfix: remove with new regime
        AdapterMicroFib                 = (1<<17),
        BIOSFibPath                     = (1<<18),
        FastResponseCapable             = (1<<19),
        ApiFib                          = (1<<20),      /* Its an API Fib */
        /* PMC NEW COMM: There is no more AIF data pending */
        NoMoreAifDataAvailable          = (1<<21)
};

/*
 *      The following defines needs to be updated any time there is an
 *      incompatible change made to the aac_init structure.
 */

#define ADAPTER_INIT_STRUCT_REVISION            3
#define ADAPTER_INIT_STRUCT_REVISION_4          4 // rocket science
#define ADAPTER_INIT_STRUCT_REVISION_6          6 /* PMC src */
#define ADAPTER_INIT_STRUCT_REVISION_7          7 /* Denali */
#define ADAPTER_INIT_STRUCT_REVISION_8          8 // Thor

union aac_init
{
        struct _r7 {
                __le32  init_struct_revision;
                __le32  no_of_msix_vectors;
                __le32  fsrev;
                __le32  comm_header_address;
                __le32  fast_io_comm_area_address;
                __le32  adapter_fibs_physical_address;
                __le32  adapter_fibs_virtual_address;
                __le32  adapter_fibs_size;
                __le32  adapter_fib_align;
                __le32  printfbuf;
                __le32  printfbufsiz;
                /* number of 4k pages of host phys. mem. */
                __le32  host_phys_mem_pages;
                /* number of seconds since 1970. */
                __le32  host_elapsed_seconds;
                /* ADAPTER_INIT_STRUCT_REVISION_4 begins here */
                __le32  init_flags;     /* flags for supported features */
#define INITFLAGS_NEW_COMM_SUPPORTED    0x00000001
#define INITFLAGS_DRIVER_USES_UTC_TIME  0x00000010
#define INITFLAGS_DRIVER_SUPPORTS_PM    0x00000020
#define INITFLAGS_NEW_COMM_TYPE1_SUPPORTED      0x00000040
#define INITFLAGS_FAST_JBOD_SUPPORTED   0x00000080
#define INITFLAGS_NEW_COMM_TYPE2_SUPPORTED      0x00000100
#define INITFLAGS_DRIVER_SUPPORTS_HBA_MODE  0x00000400
                __le32  max_io_commands;        /* max outstanding commands */
                __le32  max_io_size;    /* largest I/O command */
                __le32  max_fib_size;   /* largest FIB to adapter */
                /* ADAPTER_INIT_STRUCT_REVISION_5 begins here */
                __le32  max_num_aif;    /* max number of aif */
                /* ADAPTER_INIT_STRUCT_REVISION_6 begins here */
                /* Host RRQ (response queue) for SRC */
                __le32  host_rrq_addr_low;
                __le32  host_rrq_addr_high;
        } r7;
        struct _r8 {
                /* ADAPTER_INIT_STRUCT_REVISION_8 */
                __le32  init_struct_revision;
                __le32  rr_queue_count;
                __le32  host_elapsed_seconds; /* number of secs since 1970. */
                __le32  init_flags;
                __le32  max_io_size;    /* largest I/O command */
                __le32  max_num_aif;    /* max number of aif */
                __le32  reserved1;
                __le32  reserved2;
                struct _rrq {
                        __le32  host_addr_low;
                        __le32  host_addr_high;
                        __le16  msix_id;
                        __le16  element_count;
                        __le16  comp_thresh;
                        __le16  unused;
                } rrq[1];               /* up to 64 RRQ addresses */
        } r8;
};

enum aac_log_level {
        LOG_AAC_INIT                    = 10,
        LOG_AAC_INFORMATIONAL           = 20,
        LOG_AAC_WARNING                 = 30,
        LOG_AAC_LOW_ERROR               = 40,
        LOG_AAC_MEDIUM_ERROR            = 50,
        LOG_AAC_HIGH_ERROR              = 60,
        LOG_AAC_PANIC                   = 70,
        LOG_AAC_DEBUG                   = 80,
        LOG_AAC_WINDBG_PRINT            = 90
};

#define FSAFS_NTC_GET_ADAPTER_FIB_CONTEXT       0x030b
#define FSAFS_NTC_FIB_CONTEXT                   0x030c

struct aac_dev;
struct fib;
struct scsi_cmnd;

struct adapter_ops
{
        /* Low level operations */
        void (*adapter_interrupt)(struct aac_dev *dev);
        void (*adapter_notify)(struct aac_dev *dev, u32 event);
        void (*adapter_disable_int)(struct aac_dev *dev);
        void (*adapter_enable_int)(struct aac_dev *dev);
        int  (*adapter_sync_cmd)(struct aac_dev *dev, u32 command, u32 p1, u32 p2, u32 p3, u32 p4, u32 p5, u32 p6, u32 *status, u32 *r1, u32 *r2, u32 *r3, u32 *r4);
        int  (*adapter_check_health)(struct aac_dev *dev);
        int  (*adapter_restart)(struct aac_dev *dev, int bled, u8 reset_type);
        void (*adapter_start)(struct aac_dev *dev);
        /* Transport operations */
        int  (*adapter_ioremap)(struct aac_dev * dev, u32 size);
        irq_handler_t adapter_intr;
        /* Packet operations */
        int  (*adapter_deliver)(struct fib * fib);
        int  (*adapter_bounds)(struct aac_dev * dev, struct scsi_cmnd * cmd, u64 lba);
        int  (*adapter_read)(struct fib * fib, struct scsi_cmnd * cmd, u64 lba, u32 count);
        int  (*adapter_write)(struct fib * fib, struct scsi_cmnd * cmd, u64 lba, u32 count, int fua);
        int  (*adapter_scsi)(struct fib * fib, struct scsi_cmnd * cmd);
        /* Administrative operations */
        int  (*adapter_comm)(struct aac_dev * dev, int comm);
};

/*
 *      Define which interrupt handler needs to be installed
 */

struct aac_driver_ident
{
        int     (*init)(struct aac_dev *dev);
        char *  name;
        char *  vname;
        char *  model;
        u16     channels;
        int     quirks;
};
/*
 * Some adapter firmware needs communication memory
 * below 2gig. This tells the init function to set the
 * dma mask such that fib memory will be allocated where the
 * adapter firmware can get to it.
 */
#define AAC_QUIRK_31BIT 0x0001

/*
 * Some adapter firmware, when the raid card's cache is turned off, can not
 * split up scatter gathers in order to deal with the limits of the
 * underlying CHIM. This limit is 34 scatter gather elements.
 */
#define AAC_QUIRK_34SG  0x0002

/*
 * This adapter is a slave (no Firmware)
 */
#define AAC_QUIRK_SLAVE 0x0004

/*
 * This adapter is a master.
 */
#define AAC_QUIRK_MASTER 0x0008

/*
 * Some adapter firmware perform poorly when it must split up scatter gathers
 * in order to deal with the limits of the underlying CHIM. This limit in this
 * class of adapters is 17 scatter gather elements.
 */
#define AAC_QUIRK_17SG  0x0010

/*
 *      Some adapter firmware does not support 64 bit scsi passthrough
 * commands.
 */
#define AAC_QUIRK_SCSI_32       0x0020

/*
 * SRC based adapters support the AifReqEvent functions
 */
#define AAC_QUIRK_SRC 0x0040

/*
 *      The adapter interface specs all queues to be located in the same
 *      physically contiguous block. The host structure that defines the
 *      commuication queues will assume they are each a separate physically
 *      contiguous memory region that will support them all being one big
 *      contiguous block.
 *      There is a command and response queue for each level and direction of
 *      commuication. These regions are accessed by both the host and adapter.
 */

struct aac_queue {
        u64                     logical;        /*address we give the adapter */
        struct aac_entry        *base;          /*system virtual address */
        struct aac_qhdr         headers;        /*producer,consumer q headers*/
        u32                     entries;        /*Number of queue entries */
        wait_queue_head_t       qfull;          /*Event to wait on if q full */
        wait_queue_head_t       cmdready;       /*Cmd ready from the adapter */
                /* This is only valid for adapter to host command queues. */
        spinlock_t              *lock;          /* Spinlock for this queue must take this lock before accessing the lock */
        spinlock_t              lockdata;       /* Actual lock (used only on one side of the lock) */
        struct list_head        cmdq;           /* A queue of FIBs which need to be prcessed by the FS thread. This is */
                                                /* only valid for command queues which receive entries from the adapter. */
        /* Number of entries on outstanding queue. */

        atomic_t                numpending;
        struct aac_dev *        dev;            /* Back pointer to adapter structure */
};

/*
 *      Message queues. The order here is important, see also the
 *      queue type ordering
 */

struct aac_queue_block
{
        struct aac_queue queue[8];
};

/*
 *      SaP1 Message Unit Registers
 */

struct sa_drawbridge_CSR {
                                /*      Offset  |  Name */
        __le32  reserved[10];   /*      00h-27h |  Reserved */
        u8      LUT_Offset;     /*      28h     |  Lookup Table Offset */
        u8      reserved1[3];   /*      29h-2bh |  Reserved */
        __le32  LUT_Data;       /*      2ch     |  Looup Table Data */
        __le32  reserved2[26];  /*      30h-97h |  Reserved */
        __le16  PRICLEARIRQ;    /*      98h     |  Primary Clear Irq */
        __le16  SECCLEARIRQ;    /*      9ah     |  Secondary Clear Irq */
        __le16  PRISETIRQ;      /*      9ch     |  Primary Set Irq */
        __le16  SECSETIRQ;      /*      9eh     |  Secondary Set Irq */
        __le16  PRICLEARIRQMASK;/*      a0h     |  Primary Clear Irq Mask */
        __le16  SECCLEARIRQMASK;/*      a2h     |  Secondary Clear Irq Mask */
        __le16  PRISETIRQMASK;  /*      a4h     |  Primary Set Irq Mask */
        __le16  SECSETIRQMASK;  /*      a6h     |  Secondary Set Irq Mask */
        __le32  MAILBOX0;       /*      a8h     |  Scratchpad 0 */
        __le32  MAILBOX1;       /*      ach     |  Scratchpad 1 */
        __le32  MAILBOX2;       /*      b0h     |  Scratchpad 2 */
        __le32  MAILBOX3;       /*      b4h     |  Scratchpad 3 */
        __le32  MAILBOX4;       /*      b8h     |  Scratchpad 4 */
        __le32  MAILBOX5;       /*      bch     |  Scratchpad 5 */
        __le32  MAILBOX6;       /*      c0h     |  Scratchpad 6 */
        __le32  MAILBOX7;       /*      c4h     |  Scratchpad 7 */
        __le32  ROM_Setup_Data; /*      c8h     |  Rom Setup and Data */
        __le32  ROM_Control_Addr;/*     cch     |  Rom Control and Address */
        __le32  reserved3[12];  /*      d0h-ffh |  reserved */
        __le32  LUT[64];        /*    100h-1ffh |  Lookup Table Entries */
};

#define Mailbox0        SaDbCSR.MAILBOX0
#define Mailbox1        SaDbCSR.MAILBOX1
#define Mailbox2        SaDbCSR.MAILBOX2
#define Mailbox3        SaDbCSR.MAILBOX3
#define Mailbox4        SaDbCSR.MAILBOX4
#define Mailbox5        SaDbCSR.MAILBOX5
#define Mailbox6        SaDbCSR.MAILBOX6
#define Mailbox7        SaDbCSR.MAILBOX7

#define DoorbellReg_p SaDbCSR.PRISETIRQ
#define DoorbellReg_s SaDbCSR.SECSETIRQ
#define DoorbellClrReg_p SaDbCSR.PRICLEARIRQ


#define DOORBELL_0      0x0001
#define DOORBELL_1      0x0002
#define DOORBELL_2      0x0004
#define DOORBELL_3      0x0008
#define DOORBELL_4      0x0010
#define DOORBELL_5      0x0020
#define DOORBELL_6      0x0040


#define PrintfReady     DOORBELL_5
#define PrintfDone      DOORBELL_5

struct sa_registers {
        struct sa_drawbridge_CSR        SaDbCSR;                        /* 98h - c4h */
};


#define SA_INIT_NUM_MSIXVECTORS         1
#define SA_MINIPORT_REVISION            SA_INIT_NUM_MSIXVECTORS

#define sa_readw(AEP, CSR)              readl(&((AEP)->regs.sa->CSR))
#define sa_readl(AEP, CSR)              readl(&((AEP)->regs.sa->CSR))
#define sa_writew(AEP, CSR, value)      writew(value, &((AEP)->regs.sa->CSR))
#define sa_writel(AEP, CSR, value)      writel(value, &((AEP)->regs.sa->CSR))

/*
 *      Rx Message Unit Registers
 */

struct rx_mu_registers {
                            /*  Local  | PCI*| Name */
        __le32  ARSR;       /*  1300h  | 00h | APIC Register Select Register */
        __le32  reserved0;  /*  1304h  | 04h | Reserved */
        __le32  AWR;        /*  1308h  | 08h | APIC Window Register */
        __le32  reserved1;  /*  130Ch  | 0Ch | Reserved */
        __le32  IMRx[2];    /*  1310h  | 10h | Inbound Message Registers */
        __le32  OMRx[2];    /*  1318h  | 18h | Outbound Message Registers */
        __le32  IDR;        /*  1320h  | 20h | Inbound Doorbell Register */
        __le32  IISR;       /*  1324h  | 24h | Inbound Interrupt
                                                Status Register */
        __le32  IIMR;       /*  1328h  | 28h | Inbound Interrupt
                                                Mask Register */
        __le32  ODR;        /*  132Ch  | 2Ch | Outbound Doorbell Register */
        __le32  OISR;       /*  1330h  | 30h | Outbound Interrupt
                                                Status Register */
        __le32  OIMR;       /*  1334h  | 34h | Outbound Interrupt
                                                Mask Register */
        __le32  reserved2;  /*  1338h  | 38h | Reserved */
        __le32  reserved3;  /*  133Ch  | 3Ch | Reserved */
        __le32  InboundQueue;/* 1340h  | 40h | Inbound Queue Port relative to firmware */
        __le32  OutboundQueue;/*1344h  | 44h | Outbound Queue Port relative to firmware */
                            /* * Must access through ATU Inbound
                                 Translation Window */
};

struct rx_inbound {
        __le32  Mailbox[8];
};

#define INBOUNDDOORBELL_0       0x00000001
#define INBOUNDDOORBELL_1       0x00000002
#define INBOUNDDOORBELL_2       0x00000004
#define INBOUNDDOORBELL_3       0x00000008
#define INBOUNDDOORBELL_4       0x00000010
#define INBOUNDDOORBELL_5       0x00000020
#define INBOUNDDOORBELL_6       0x00000040

#define OUTBOUNDDOORBELL_0      0x00000001
#define OUTBOUNDDOORBELL_1      0x00000002
#define OUTBOUNDDOORBELL_2      0x00000004
#define OUTBOUNDDOORBELL_3      0x00000008
#define OUTBOUNDDOORBELL_4      0x00000010

#define InboundDoorbellReg      MUnit.IDR
#define OutboundDoorbellReg     MUnit.ODR

struct rx_registers {
        struct rx_mu_registers          MUnit;          /* 1300h - 1347h */
        __le32                          reserved1[2];   /* 1348h - 134ch */
        struct rx_inbound               IndexRegs;
};

#define rx_readb(AEP, CSR)              readb(&((AEP)->regs.rx->CSR))
#define rx_readl(AEP, CSR)              readl(&((AEP)->regs.rx->CSR))
#define rx_writeb(AEP, CSR, value)      writeb(value, &((AEP)->regs.rx->CSR))
#define rx_writel(AEP, CSR, value)      writel(value, &((AEP)->regs.rx->CSR))

/*
 *      Rkt Message Unit Registers (same as Rx, except a larger reserve region)
 */

#define rkt_mu_registers rx_mu_registers
#define rkt_inbound rx_inbound

struct rkt_registers {
        struct rkt_mu_registers         MUnit;           /* 1300h - 1347h */
        __le32                          reserved1[1006]; /* 1348h - 22fch */
        struct rkt_inbound              IndexRegs;       /* 2300h - */
};

#define rkt_readb(AEP, CSR)             readb(&((AEP)->regs.rkt->CSR))
#define rkt_readl(AEP, CSR)             readl(&((AEP)->regs.rkt->CSR))
#define rkt_writeb(AEP, CSR, value)     writeb(value, &((AEP)->regs.rkt->CSR))
#define rkt_writel(AEP, CSR, value)     writel(value, &((AEP)->regs.rkt->CSR))

/*
 * PMC SRC message unit registers
 */

#define src_inbound rx_inbound

struct src_mu_registers {
                                /*  PCI*| Name */
        __le32  reserved0[6];   /*  00h | Reserved */
        __le32  IOAR[2];        /*  18h | IOA->host interrupt register */
        __le32  IDR;            /*  20h | Inbound Doorbell Register */
        __le32  IISR;           /*  24h | Inbound Int. Status Register */
        __le32  reserved1[3];   /*  28h | Reserved */
        __le32  OIMR;           /*  34h | Outbound Int. Mask Register */
        __le32  reserved2[25];  /*  38h | Reserved */
        __le32  ODR_R;          /*  9ch | Outbound Doorbell Read */
        __le32  ODR_C;          /*  a0h | Outbound Doorbell Clear */
        __le32  reserved3[3];   /*  a4h | Reserved */
        __le32  SCR0;           /*  b0h | Scratchpad 0 */
        __le32  reserved4[2];   /*  b4h | Reserved */
        __le32  OMR;            /*  bch | Outbound Message Register */
        __le32  IQ_L;           /*  c0h | Inbound Queue (Low address) */
        __le32  IQ_H;           /*  c4h | Inbound Queue (High address) */
        __le32  ODR_MSI;        /*  c8h | MSI register for sync./AIF */
        __le32  reserved5;      /*  cch | Reserved */
        __le32  IQN_L;          /*  d0h | Inbound (native cmd) low  */
        __le32  IQN_H;          /*  d4h | Inbound (native cmd) high */
};

struct src_registers {
        struct src_mu_registers MUnit;  /* 00h - cbh */
        union {
                struct {
                        __le32 reserved1[130786];       /* d8h - 7fc5fh */
                        struct src_inbound IndexRegs;   /* 7fc60h */
                } tupelo;
                struct {
                        __le32 reserved1[970];          /* d8h - fffh */
                        struct src_inbound IndexRegs;   /* 1000h */
                } denali;
        } u;
};

#define src_readb(AEP, CSR)             readb(&((AEP)->regs.src.bar0->CSR))
#define src_readl(AEP, CSR)             readl(&((AEP)->regs.src.bar0->CSR))
#define src_writeb(AEP, CSR, value)     writeb(value, \
                                                &((AEP)->regs.src.bar0->CSR))
#define src_writel(AEP, CSR, value)     writel(value, \
                                                &((AEP)->regs.src.bar0->CSR))
#if defined(writeq)
#define src_writeq(AEP, CSR, value)     writeq(value, \
                                                &((AEP)->regs.src.bar0->CSR))
#endif

#define SRC_ODR_SHIFT           12
#define SRC_IDR_SHIFT           9
#define SRC_MSI_READ_MASK       0x1000

typedef void (*fib_callback)(void *ctxt, struct fib *fibctx);

struct aac_fib_context {
        s16                     type;           // used for verification of structure
        s16                     size;
        u32                     unique;         // unique value representing this context
        ulong                   jiffies;        // used for cleanup - dmb changed to ulong
        struct list_head        next;           // used to link context's into a linked list
        struct completion       completion;     // this is used to wait for the next fib to arrive.
        int                     wait;           // Set to true when thread is in WaitForSingleObject
        unsigned long           count;          // total number of FIBs on FibList
        struct list_head        fib_list;       // this holds fibs and their attachd hw_fibs
};

struct sense_data {
        u8 error_code;          /* 70h (current errors), 71h(deferred errors) */
        u8 valid:1;             /* A valid bit of one indicates that the information  */
                                /* field contains valid information as defined in the
                                 * SCSI-2 Standard.
                                 */
        u8 segment_number;      /* Only used for COPY, COMPARE, or COPY AND VERIFY Commands */
        u8 sense_key:4;         /* Sense Key */
        u8 reserved:1;
        u8 ILI:1;               /* Incorrect Length Indicator */
        u8 EOM:1;               /* End Of Medium - reserved for random access devices */
        u8 filemark:1;          /* Filemark - reserved for random access devices */

        u8 information[4];      /* for direct-access devices, contains the unsigned
                                 * logical block address or residue associated with
                                 * the sense key
                                 */
        u8 add_sense_len;       /* number of additional sense bytes to follow this field */
        u8 cmnd_info[4];        /* not used */
        u8 ASC;                 /* Additional Sense Code */
        u8 ASCQ;                /* Additional Sense Code Qualifier */
        u8 FRUC;                /* Field Replaceable Unit Code - not used */
        u8 bit_ptr:3;           /* indicates which byte of the CDB or parameter data
                                 * was in error
                                 */
        u8 BPV:1;               /* bit pointer valid (BPV): 1- indicates that
                                 * the bit_ptr field has valid value
                                 */
        u8 reserved2:2;
        u8 CD:1;                /* command data bit: 1- illegal parameter in CDB.
                                 * 0- illegal parameter in data.
                                 */
        u8 SKSV:1;
        u8 field_ptr[2];        /* byte of the CDB or parameter data in error */
};

struct fsa_dev_info {
        u64             last;
        u64             size;
        u32             type;
        u32             config_waiting_on;
        unsigned long   config_waiting_stamp;
        u16             queue_depth;
        u8              config_needed;
        u8              valid;
        u8              ro;
        u8              locked;
        u8              deleted;
        char            devname[8];
        struct sense_data sense_data;
        u32             block_size;
        u8              identifier[16];
};

struct fib {
        void                    *next;  /* this is used by the allocator */
        s16                     type;
        s16                     size;
        /*
         *      The Adapter that this I/O is destined for.
         */
        struct aac_dev          *dev;
        /*
         *      This is the event the sendfib routine will wait on if the
         *      caller did not pass one and this is synch io.
         */
        struct completion       event_wait;
        spinlock_t              event_lock;

        u32                     done;   /* gets set to 1 when fib is complete */
        fib_callback            callback;
        void                    *callback_data;
        u32                     flags; // u32 dmb was ulong
        /*
         *      And for the internal issue/reply queues (we may be able
         *      to merge these two)
         */
        struct list_head        fiblink;
        void                    *data;
        u32                     vector_no;
        struct hw_fib           *hw_fib_va;     /* also used for native */
        dma_addr_t              hw_fib_pa;      /* physical address of hw_fib*/
        dma_addr_t              hw_sgl_pa;      /* extra sgl for native */
        dma_addr_t              hw_error_pa;    /* error buffer for native */
        u32                     hbacmd_size;    /* cmd size for native */
};

#define AAC_INIT                        0
#define AAC_RESCAN                      1

#define AAC_DEVTYPE_RAID_MEMBER 1
#define AAC_DEVTYPE_ARC_RAW             2
#define AAC_DEVTYPE_NATIVE_RAW          3

#define AAC_RESCAN_DELAY                (10 * HZ)

struct aac_hba_map_info {
        __le32  rmw_nexus;              /* nexus for native HBA devices */
        u8              devtype;        /* device type */
        s8              reset_state;    /* 0 - no reset, 1..x - */
                                        /* after xth TM LUN reset */
        u16             qd_limit;
        u32             scan_counter;
        struct aac_ciss_identify_pd  *safw_identify_resp;
};

/*
 *      Adapter Information Block
 *
 *      This is returned by the RequestAdapterInfo block
 */

struct aac_adapter_info
{
        __le32  platform;
        __le32  cpu;
        __le32  subcpu;
        __le32  clock;
        __le32  execmem;
        __le32  buffermem;
        __le32  totalmem;
        __le32  kernelrev;
        __le32  kernelbuild;
        __le32  monitorrev;
        __le32  monitorbuild;
        __le32  hwrev;
        __le32  hwbuild;
        __le32  biosrev;
        __le32  biosbuild;
        __le32  cluster;
        __le32  clusterchannelmask;
        __le32  serial[2];
        __le32  battery;
        __le32  options;
        __le32  OEM;
};

struct aac_supplement_adapter_info
{
        u8      adapter_type_text[17+1];
        u8      pad[2];
        __le32  flash_memory_byte_size;
        __le32  flash_image_id;
        __le32  max_number_ports;
        __le32  version;
        __le32  feature_bits;
        u8      slot_number;
        u8      reserved_pad0[3];
        u8      build_date[12];
        __le32  current_number_ports;
        struct {
                u8      assembly_pn[8];
                u8      fru_pn[8];
                u8      battery_fru_pn[8];
                u8      ec_version_string[8];
                u8      tsid[12];
        }       vpd_info;
        __le32  flash_firmware_revision;
        __le32  flash_firmware_build;
        __le32  raid_type_morph_options;
        __le32  flash_firmware_boot_revision;
        __le32  flash_firmware_boot_build;
        u8      mfg_pcba_serial_no[12];
        u8      mfg_wwn_name[8];
        __le32  supported_options2;
        __le32  struct_expansion;
        /* StructExpansion == 1 */
        __le32  feature_bits3;
        __le32  supported_performance_modes;
        u8      host_bus_type;          /* uses HOST_BUS_TYPE_xxx defines */
        u8      host_bus_width;         /* actual width in bits or links */
        u16     host_bus_speed;         /* actual bus speed/link rate in MHz */
        u8      max_rrc_drives;         /* max. number of ITP-RRC drives/pool */
        u8      max_disk_xtasks;        /* max. possible num of DiskX Tasks */

        u8      cpld_ver_loaded;
        u8      cpld_ver_in_flash;

        __le64  max_rrc_capacity;
        __le32  compiled_max_hist_log_level;
        u8      custom_board_name[12];
        u16     supported_cntlr_mode;   /* identify supported controller mode */
        u16     reserved_for_future16;
        __le32  supported_options3;     /* reserved for future options */

        __le16  virt_device_bus;                /* virt. SCSI device for Thor */
        __le16  virt_device_target;
        __le16  virt_device_lun;
        __le16  unused;
        __le32  reserved_for_future_growth[68];

};
#define AAC_FEATURE_FALCON      cpu_to_le32(0x00000010)
#define AAC_FEATURE_JBOD        cpu_to_le32(0x08000000)
/* SupportedOptions2 */
#define AAC_OPTION_MU_RESET             cpu_to_le32(0x00000001)
#define AAC_OPTION_IGNORE_RESET         cpu_to_le32(0x00000002)
#define AAC_OPTION_POWER_MANAGEMENT     cpu_to_le32(0x00000004)
#define AAC_OPTION_DOORBELL_RESET       cpu_to_le32(0x00004000)
/* 4KB sector size */
#define AAC_OPTION_VARIABLE_BLOCK_SIZE  cpu_to_le32(0x00040000)
/* 240 simple volume support */
#define AAC_OPTION_SUPPORTED_240_VOLUMES cpu_to_le32(0x10000000)
/*
 * Supports FIB dump sync command send prior to IOP_RESET
 */
#define AAC_OPTION_SUPPORTED3_IOP_RESET_FIB_DUMP        cpu_to_le32(0x00004000)
#define AAC_SIS_VERSION_V3      3
#define AAC_SIS_SLOT_UNKNOWN    0xFF

#define GetBusInfo 0x00000009
struct aac_bus_info {
        __le32  Command;        /* VM_Ioctl */
        __le32  ObjType;        /* FT_DRIVE */
        __le32  MethodId;       /* 1 = SCSI Layer */
        __le32  ObjectId;       /* Handle */
        __le32  CtlCmd;         /* GetBusInfo */
};

struct aac_bus_info_response {
        __le32  Status;         /* ST_OK */
        __le32  ObjType;
        __le32  MethodId;       /* unused */
        __le32  ObjectId;       /* unused */
        __le32  CtlCmd;         /* unused */
        __le32  ProbeComplete;
        __le32  BusCount;
        __le32  TargetsPerBus;
        u8      InitiatorBusId[10];
        u8      BusValid[10];
};

/*
 * Battery platforms
 */
#define AAC_BAT_REQ_PRESENT     (1)
#define AAC_BAT_REQ_NOTPRESENT  (2)
#define AAC_BAT_OPT_PRESENT     (3)
#define AAC_BAT_OPT_NOTPRESENT  (4)
#define AAC_BAT_NOT_SUPPORTED   (5)
/*
 * cpu types
 */
#define AAC_CPU_SIMULATOR       (1)
#define AAC_CPU_I960            (2)
#define AAC_CPU_STRONGARM       (3)

/*
 * Supported Options
 */
#define AAC_OPT_SNAPSHOT                cpu_to_le32(1)
#define AAC_OPT_CLUSTERS                cpu_to_le32(1<<1)
#define AAC_OPT_WRITE_CACHE             cpu_to_le32(1<<2)
#define AAC_OPT_64BIT_DATA              cpu_to_le32(1<<3)
#define AAC_OPT_HOST_TIME_FIB           cpu_to_le32(1<<4)
#define AAC_OPT_RAID50                  cpu_to_le32(1<<5)
#define AAC_OPT_4GB_WINDOW              cpu_to_le32(1<<6)
#define AAC_OPT_SCSI_UPGRADEABLE        cpu_to_le32(1<<7)
#define AAC_OPT_SOFT_ERR_REPORT         cpu_to_le32(1<<8)
#define AAC_OPT_SUPPORTED_RECONDITION   cpu_to_le32(1<<9)
#define AAC_OPT_SGMAP_HOST64            cpu_to_le32(1<<10)
#define AAC_OPT_ALARM                   cpu_to_le32(1<<11)
#define AAC_OPT_NONDASD                 cpu_to_le32(1<<12)
#define AAC_OPT_SCSI_MANAGED            cpu_to_le32(1<<13)
#define AAC_OPT_RAID_SCSI_MODE          cpu_to_le32(1<<14)
#define AAC_OPT_SUPPLEMENT_ADAPTER_INFO cpu_to_le32(1<<16)
#define AAC_OPT_NEW_COMM                cpu_to_le32(1<<17)
#define AAC_OPT_NEW_COMM_64             cpu_to_le32(1<<18)
#define AAC_OPT_EXTENDED                cpu_to_le32(1<<23)
#define AAC_OPT_NATIVE_HBA              cpu_to_le32(1<<25)
#define AAC_OPT_NEW_COMM_TYPE1          cpu_to_le32(1<<28)
#define AAC_OPT_NEW_COMM_TYPE2          cpu_to_le32(1<<29)
#define AAC_OPT_NEW_COMM_TYPE3          cpu_to_le32(1<<30)
#define AAC_OPT_NEW_COMM_TYPE4          cpu_to_le32(1<<31)

#define AAC_COMM_PRODUCER               0
#define AAC_COMM_MESSAGE                1
#define AAC_COMM_MESSAGE_TYPE1          3
#define AAC_COMM_MESSAGE_TYPE2          4
#define AAC_COMM_MESSAGE_TYPE3          5

#define AAC_EXTOPT_SA_FIRMWARE          cpu_to_le32(1<<1)
#define AAC_EXTOPT_SOFT_RESET           cpu_to_le32(1<<16)

/* MSIX context */
struct aac_msix_ctx {
        int             vector_no;
        struct aac_dev  *dev;
};

struct aac_dev
{
        struct list_head        entry;
        const char              *name;
        int                     id;

        /*
         *      negotiated FIB settings
         */
        unsigned int            max_fib_size;
        unsigned int            sg_tablesize;
        unsigned int            max_num_aif;

        unsigned int            max_cmd_size;   /* max_fib_size or MAX_NATIVE */

        /*
         *      Map for 128 fib objects (64k)
         */
        dma_addr_t              hw_fib_pa;      /* also used for native cmd */
        struct hw_fib           *hw_fib_va;     /* also used for native cmd */
        struct hw_fib           *aif_base_va;
        /*
         *      Fib Headers
         */
        struct fib              *fibs;

        struct fib              *free_fib;
        spinlock_t              fib_lock;

        struct mutex            ioctl_mutex;
        struct mutex            scan_mutex;
        struct aac_queue_block *queues;
        /*
         *      The user API will use an IOCTL to register itself to receive
         *      FIBs from the adapter.  The following list is used to keep
         *      track of all the threads that have requested these FIBs.  The
         *      mutex is used to synchronize access to all data associated
         *      with the adapter fibs.
         */
        struct list_head        fib_list;

        struct adapter_ops      a_ops;
        unsigned long           fsrev;          /* Main driver's revision number */

        resource_size_t         base_start;     /* main IO base */
        resource_size_t         dbg_base;       /* address of UART
                                                 * debug buffer */

        resource_size_t         base_size, dbg_size;    /* Size of
                                                         *  mapped in region */
        /*
         * Holds initialization info
         * to communicate with adapter
         */
        union aac_init          *init;
        dma_addr_t              init_pa;        /* Holds physical address of the init struct */
        /* response queue (if AAC_COMM_MESSAGE_TYPE1) */
        __le32                  *host_rrq;
        dma_addr_t              host_rrq_pa;    /* phys. address */
        /* index into rrq buffer */
        u32                     host_rrq_idx[AAC_MAX_MSIX];
        atomic_t                rrq_outstanding[AAC_MAX_MSIX];
        u32                     fibs_pushed_no;
        struct pci_dev          *pdev;          /* Our PCI interface */
        /* pointer to buffer used for printf's from the adapter */
        void                    *printfbuf;
        void                    *comm_addr;     /* Base address of Comm area */
        dma_addr_t              comm_phys;      /* Physical Address of Comm area */
        size_t                  comm_size;

        struct Scsi_Host        *scsi_host_ptr;
        int                     maximum_num_containers;
        int                     maximum_num_physicals;
        int                     maximum_num_channels;
        struct fsa_dev_info     *fsa_dev;
        struct task_struct      *thread;
        struct delayed_work     safw_rescan_work;
        struct delayed_work     src_reinit_aif_worker;
        int                     cardtype;
        /*
         *This lock will protect the two 32-bit
         *writes to the Inbound Queue
         */
        spinlock_t              iq_lock;

        /*
         *      The following is the device specific extension.
         */
#ifndef AAC_MIN_FOOTPRINT_SIZE
#       define AAC_MIN_FOOTPRINT_SIZE 8192
#       define AAC_MIN_SRC_BAR0_SIZE 0x400000
#       define AAC_MIN_SRC_BAR1_SIZE 0x800
#       define AAC_MIN_SRCV_BAR0_SIZE 0x100000
#       define AAC_MIN_SRCV_BAR1_SIZE 0x400
#endif
        union
        {
                struct sa_registers __iomem *sa;
                struct rx_registers __iomem *rx;
                struct rkt_registers __iomem *rkt;
                struct {
                        struct src_registers __iomem *bar0;
                        char __iomem *bar1;
                } src;
        } regs;
        volatile void __iomem *base, *dbg_base_mapped;
        volatile struct rx_inbound __iomem *IndexRegs;
        u32                     OIMR; /* Mask Register Cache */
        /*
         *      AIF thread states
         */
        u32                     aif_thread;
        struct aac_adapter_info adapter_info;
        struct aac_supplement_adapter_info supplement_adapter_info;
        /* These are in adapter info but they are in the io flow so
         * lets break them out so we don't have to do an AND to check them
         */
        u8                      nondasd_support;
        u8                      jbod;
        u8                      cache_protected;
        u8                      dac_support;
        u8                      needs_dac;
        u8                      raid_scsi_mode;
        u8                      comm_interface;
        u8                      raw_io_interface;
        u8                      raw_io_64;
        u8                      printf_enabled;
        u8                      in_reset;
        u8                      in_soft_reset;
        u8                      msi;
        u8                      sa_firmware;
        int                     management_fib_count;
        spinlock_t              manage_lock;
        spinlock_t              sync_lock;
        int                     sync_mode;
        struct fib              *sync_fib;
        struct list_head        sync_fib_list;
        u32                     doorbell_mask;
        u32                     max_msix;       /* max. MSI-X vectors */
        u32                     vector_cap;     /* MSI-X vector capab.*/
        int                     msi_enabled;    /* MSI/MSI-X enabled */
        atomic_t                msix_counter;
        u32                     scan_counter;
        struct msix_entry       msixentry[AAC_MAX_MSIX];
        struct aac_msix_ctx     aac_msix[AAC_MAX_MSIX]; /* context */
        struct aac_hba_map_info hba_map[AAC_MAX_BUSES][AAC_MAX_TARGETS];
        struct aac_ciss_phys_luns_resp *safw_phys_luns;
        u8                      adapter_shutdown;
        u32                     handle_pci_error;
        bool                    init_reset;
        u8                      soft_reset_support;
};

#define aac_adapter_interrupt(dev) \
        (dev)->a_ops.adapter_interrupt(dev)

#define aac_adapter_notify(dev, event) \
        (dev)->a_ops.adapter_notify(dev, event)

#define aac_adapter_disable_int(dev) \
        (dev)->a_ops.adapter_disable_int(dev)

#define aac_adapter_enable_int(dev) \
        (dev)->a_ops.adapter_enable_int(dev)

#define aac_adapter_sync_cmd(dev, command, p1, p2, p3, p4, p5, p6, status, r1, r2, r3, r4) \
        (dev)->a_ops.adapter_sync_cmd(dev, command, p1, p2, p3, p4, p5, p6, status, r1, r2, r3, r4)

#define aac_adapter_restart(dev, bled, reset_type) \
        ((dev)->a_ops.adapter_restart(dev, bled, reset_type))

#define aac_adapter_start(dev) \
        ((dev)->a_ops.adapter_start(dev))

#define aac_adapter_ioremap(dev, size) \
        (dev)->a_ops.adapter_ioremap(dev, size)

#define aac_adapter_deliver(fib) \
        ((fib)->dev)->a_ops.adapter_deliver(fib)

#define aac_adapter_bounds(dev,cmd,lba) \
        dev->a_ops.adapter_bounds(dev,cmd,lba)

#define aac_adapter_read(fib,cmd,lba,count) \
        ((fib)->dev)->a_ops.adapter_read(fib,cmd,lba,count)

#define aac_adapter_write(fib,cmd,lba,count,fua) \
        ((fib)->dev)->a_ops.adapter_write(fib,cmd,lba,count,fua)

#define aac_adapter_scsi(fib,cmd) \
        ((fib)->dev)->a_ops.adapter_scsi(fib,cmd)

#define aac_adapter_comm(dev,comm) \
        (dev)->a_ops.adapter_comm(dev, comm)

#define FIB_CONTEXT_FLAG_TIMED_OUT              (0x00000001)
#define FIB_CONTEXT_FLAG                        (0x00000002)
#define FIB_CONTEXT_FLAG_WAIT                   (0x00000004)
#define FIB_CONTEXT_FLAG_FASTRESP               (0x00000008)
#define FIB_CONTEXT_FLAG_NATIVE_HBA             (0x00000010)
#define FIB_CONTEXT_FLAG_NATIVE_HBA_TMF (0x00000020)
#define FIB_CONTEXT_FLAG_SCSI_CMD       (0x00000040)
#define FIB_CONTEXT_FLAG_EH_RESET       (0x00000080)

/*
 *      Define the command values
 */

#define         Null                    0
#define         GetAttributes           1
#define         SetAttributes           2
#define         Lookup                  3
#define         ReadLink                4
#define         Read                    5
#define         Write                   6
#define         Create                  7
#define         MakeDirectory           8
#define         SymbolicLink            9
#define         MakeNode                10
#define         Removex                 11
#define         RemoveDirectoryx        12
#define         Rename                  13
#define         Link                    14
#define         ReadDirectory           15
#define         ReadDirectoryPlus       16
#define         FileSystemStatus        17
#define         FileSystemInfo          18
#define         PathConfigure           19
#define         Commit                  20
#define         Mount                   21
#define         UnMount                 22
#define         Newfs                   23
#define         FsCheck                 24
#define         FsSync                  25
#define         SimReadWrite            26
#define         SetFileSystemStatus     27
#define         BlockRead               28
#define         BlockWrite              29
#define         NvramIoctl              30
#define         FsSyncWait              31
#define         ClearArchiveBit         32
#define         SetAcl                  33
#define         GetAcl                  34
#define         AssignAcl               35
#define         FaultInsertion          36      /* Fault Insertion Command */
#define         CrazyCache              37      /* Crazycache */

#define         MAX_FSACOMMAND_NUM      38


/*
 *      Define the status returns. These are very unixlike although
 *      most are not in fact used
 */

#define         ST_OK           0
#define         ST_PERM         1
#define         ST_NOENT        2
#define         ST_IO           5
#define         ST_NXIO         6
#define         ST_E2BIG        7
#define         ST_MEDERR       8
#define         ST_ACCES        13
#define         ST_EXIST        17
#define         ST_XDEV         18
#define         ST_NODEV        19
#define         ST_NOTDIR       20
#define         ST_ISDIR        21
#define         ST_INVAL        22
#define         ST_FBIG         27
#define         ST_NOSPC        28
#define         ST_ROFS         30
#define         ST_MLINK        31
#define         ST_WOULDBLOCK   35
#define         ST_NAMETOOLONG  63
#define         ST_NOTEMPTY     66
#define         ST_DQUOT        69
#define         ST_STALE        70
#define         ST_REMOTE       71
#define         ST_NOT_READY    72
#define         ST_BADHANDLE    10001
#define         ST_NOT_SYNC     10002
#define         ST_BAD_COOKIE   10003
#define         ST_NOTSUPP      10004
#define         ST_TOOSMALL     10005
#define         ST_SERVERFAULT  10006
#define         ST_BADTYPE      10007
#define         ST_JUKEBOX      10008
#define         ST_NOTMOUNTED   10009
#define         ST_MAINTMODE    10010
#define         ST_STALEACL     10011

/*
 *      On writes how does the client want the data written.
 */

#define CACHE_CSTABLE           1
#define CACHE_UNSTABLE          2

/*
 *      Lets the client know at which level the data was committed on
 *      a write request
 */

#define CMFILE_SYNCH_NVRAM      1
#define CMDATA_SYNCH_NVRAM      2
#define CMFILE_SYNCH            3
#define CMDATA_SYNCH            4
#define CMUNSTABLE              5

#define RIO_TYPE_WRITE                  0x0000
#define RIO_TYPE_READ                   0x0001
#define RIO_SUREWRITE                   0x0008

#define RIO2_IO_TYPE                    0x0003
#define RIO2_IO_TYPE_WRITE              0x0000
#define RIO2_IO_TYPE_READ               0x0001
#define RIO2_IO_TYPE_VERIFY             0x0002
#define RIO2_IO_ERROR                   0x0004
#define RIO2_IO_SUREWRITE               0x0008
#define RIO2_SGL_CONFORMANT             0x0010
#define RIO2_SG_FORMAT                  0xF000
#define RIO2_SG_FORMAT_ARC              0x0000
#define RIO2_SG_FORMAT_SRL              0x1000
#define RIO2_SG_FORMAT_IEEE1212         0x2000

struct aac_read
{
        __le32          command;
        __le32          cid;
        __le32          block;
        __le32          count;
        struct sgmap    sg;     // Must be last in struct because it is variable
};

struct aac_read64
{
        __le32          command;
        __le16          cid;
        __le16          sector_count;
        __le32          block;
        __le16          pad;
        __le16          flags;
        struct sgmap64  sg;     // Must be last in struct because it is variable
};

struct aac_read_reply
{
        __le32          status;
        __le32          count;
};

struct aac_write
{
        __le32          command;
        __le32          cid;
        __le32          block;
        __le32          count;
        __le32          stable; // Not used
        struct sgmap    sg;     // Must be last in struct because it is variable
};

struct aac_write64
{
        __le32          command;
        __le16          cid;
        __le16          sector_count;
        __le32          block;
        __le16          pad;
        __le16          flags;
        struct sgmap64  sg;     // Must be last in struct because it is variable
};
struct aac_write_reply
{
        __le32          status;
        __le32          count;
        __le32          committed;
};

struct aac_raw_io
{
        __le32          block[2];
        __le32          count;
        __le16          cid;
        __le16          flags;          /* 00 W, 01 R */
        __le16          bpTotal;        /* reserved for F/W use */
        __le16          bpComplete;     /* reserved for F/W use */
        struct sgmapraw sg;
};

struct aac_raw_io2 {
        __le32          blockLow;
        __le32          blockHigh;
        __le32          byteCount;
        __le16          cid;
        __le16          flags;          /* RIO2 flags */
        __le32          sgeFirstSize;   /* size of first sge el. */
        __le32          sgeNominalSize; /* size of 2nd sge el. (if conformant) */
        u8              sgeCnt;         /* only 8 bits required */
        u8              bpTotal;        /* reserved for F/W use */
        u8              bpComplete;     /* reserved for F/W use */
        u8              sgeFirstIndex;  /* reserved for F/W use */
        u8              unused[4];
        struct sge_ieee1212     sge[];
};

#define CT_FLUSH_CACHE 129
struct aac_synchronize {
        __le32          command;        /* VM_ContainerConfig */
        __le32          type;           /* CT_FLUSH_CACHE */
        __le32          cid;
        __le32          parm1;
        __le32          parm2;
        __le32          parm3;
        __le32          parm4;
        __le32          count;  /* sizeof(((struct aac_synchronize_reply *)NULL)->data) */
};

struct aac_synchronize_reply {
        __le32          dummy0;
        __le32          dummy1;
        __le32          status; /* CT_OK */
        __le32          parm1;
        __le32          parm2;
        __le32          parm3;
        __le32          parm4;
        __le32          parm5;
        u8              data[16];
};

#define CT_POWER_MANAGEMENT     245
#define CT_PM_START_UNIT        2
#define CT_PM_STOP_UNIT         3
#define CT_PM_UNIT_IMMEDIATE    1
struct aac_power_management {
        __le32          command;        /* VM_ContainerConfig */
        __le32          type;           /* CT_POWER_MANAGEMENT */
        __le32          sub;            /* CT_PM_* */
        __le32          cid;
        __le32          parm;           /* CT_PM_sub_* */
};

#define CT_PAUSE_IO    65
#define CT_RELEASE_IO  66
struct aac_pause {
        __le32          command;        /* VM_ContainerConfig */
        __le32          type;           /* CT_PAUSE_IO */
        __le32          timeout;        /* 10ms ticks */
        __le32          min;
        __le32          noRescan;
        __le32          parm3;
        __le32          parm4;
        __le32          count;  /* sizeof(((struct aac_pause_reply *)NULL)->data) */
};

struct aac_srb
{
        __le32          function;
        __le32          channel;
        __le32          id;
        __le32          lun;
        __le32          timeout;
        __le32          flags;
        __le32          count;          // Data xfer size
        __le32          retry_limit;
        __le32          cdb_size;
        u8              cdb[16];
        struct  sgmap   sg;
};

/*
 * This and associated data structs are used by the

 * ioctl caller and are in cpu order.
 */
struct user_aac_srb
{
        u32             function;
        u32             channel;
        u32             id;
        u32             lun;
        u32             timeout;
        u32             flags;
        u32             count;          // Data xfer size
        u32             retry_limit;
        u32             cdb_size;
        u8              cdb[16];
        struct  user_sgmap      sg;
};

#define         AAC_SENSE_BUFFERSIZE     30

struct aac_srb_reply
{
        __le32          status;
        __le32          srb_status;
        __le32          scsi_status;
        __le32          data_xfer_length;
        __le32          sense_data_size;
        u8              sense_data[AAC_SENSE_BUFFERSIZE]; // Can this be SCSI_SENSE_BUFFERSIZE
};

struct aac_srb_unit {
        struct aac_srb          srb;
        struct aac_srb_reply    srb_reply;
};

/*
 * SRB Flags
 */
#define         SRB_NoDataXfer           0x0000
#define         SRB_DisableDisconnect    0x0004
#define         SRB_DisableSynchTransfer 0x0008
#define         SRB_BypassFrozenQueue    0x0010
#define         SRB_DisableAutosense     0x0020
#define         SRB_DataIn               0x0040
#define         SRB_DataOut              0x0080

/*
 * SRB Functions - set in aac_srb->function
 */
#define SRBF_ExecuteScsi        0x0000
#define SRBF_ClaimDevice        0x0001
#define SRBF_IO_Control         0x0002
#define SRBF_ReceiveEvent       0x0003
#define SRBF_ReleaseQueue       0x0004
#define SRBF_AttachDevice       0x0005
#define SRBF_ReleaseDevice      0x0006
#define SRBF_Shutdown           0x0007
#define SRBF_Flush              0x0008
#define SRBF_AbortCommand       0x0010
#define SRBF_ReleaseRecovery    0x0011
#define SRBF_ResetBus           0x0012
#define SRBF_ResetDevice        0x0013
#define SRBF_TerminateIO        0x0014
#define SRBF_FlushQueue         0x0015
#define SRBF_RemoveDevice       0x0016
#define SRBF_DomainValidation   0x0017

/*
 * SRB SCSI Status - set in aac_srb->scsi_status
 */
#define SRB_STATUS_PENDING                  0x00
#define SRB_STATUS_SUCCESS                  0x01
#define SRB_STATUS_ABORTED                  0x02
#define SRB_STATUS_ABORT_FAILED             0x03
#define SRB_STATUS_ERROR                    0x04
#define SRB_STATUS_BUSY                     0x05
#define SRB_STATUS_INVALID_REQUEST          0x06
#define SRB_STATUS_INVALID_PATH_ID          0x07
#define SRB_STATUS_NO_DEVICE                0x08
#define SRB_STATUS_TIMEOUT                  0x09
#define SRB_STATUS_SELECTION_TIMEOUT        0x0A
#define SRB_STATUS_COMMAND_TIMEOUT          0x0B
#define SRB_STATUS_MESSAGE_REJECTED         0x0D
#define SRB_STATUS_BUS_RESET                0x0E
#define SRB_STATUS_PARITY_ERROR             0x0F
#define SRB_STATUS_REQUEST_SENSE_FAILED     0x10
#define SRB_STATUS_NO_HBA                   0x11
#define SRB_STATUS_DATA_OVERRUN             0x12
#define SRB_STATUS_UNEXPECTED_BUS_FREE      0x13
#define SRB_STATUS_PHASE_SEQUENCE_FAILURE   0x14
#define SRB_STATUS_BAD_SRB_BLOCK_LENGTH     0x15
#define SRB_STATUS_REQUEST_FLUSHED          0x16
#define SRB_STATUS_DELAYED_RETRY            0x17
#define SRB_STATUS_INVALID_LUN              0x20
#define SRB_STATUS_INVALID_TARGET_ID        0x21
#define SRB_STATUS_BAD_FUNCTION             0x22
#define SRB_STATUS_ERROR_RECOVERY           0x23
#define SRB_STATUS_NOT_STARTED              0x24
#define SRB_STATUS_NOT_IN_USE               0x30
#define SRB_STATUS_FORCE_ABORT              0x31
#define SRB_STATUS_DOMAIN_VALIDATION_FAIL   0x32

/*
 * Object-Server / Volume-Manager Dispatch Classes
 */

#define         VM_Null                 0
#define         VM_NameServe            1
#define         VM_ContainerConfig      2
#define         VM_Ioctl                3
#define         VM_FilesystemIoctl      4
#define         VM_CloseAll             5
#define         VM_CtBlockRead          6
#define         VM_CtBlockWrite         7
#define         VM_SliceBlockRead       8       /* raw access to configured "storage objects" */
#define         VM_SliceBlockWrite      9
#define         VM_DriveBlockRead       10      /* raw access to physical devices */
#define         VM_DriveBlockWrite      11
#define         VM_EnclosureMgt         12      /* enclosure management */
#define         VM_Unused               13      /* used to be diskset management */
#define         VM_CtBlockVerify        14
#define         VM_CtPerf               15      /* performance test */
#define         VM_CtBlockRead64        16
#define         VM_CtBlockWrite64       17
#define         VM_CtBlockVerify64      18
#define         VM_CtHostRead64         19
#define         VM_CtHostWrite64        20
#define         VM_DrvErrTblLog         21
#define         VM_NameServe64          22
#define         VM_NameServeAllBlk      30

#define         MAX_VMCOMMAND_NUM       23      /* used for sizing stats array - leave last */

/*
 *      Descriptive information (eg, vital stats)
 *      that a content manager might report.  The
 *      FileArray filesystem component is one example
 *      of a content manager.  Raw mode might be
 *      another.
 */

struct aac_fsinfo {
        __le32  fsTotalSize;    /* Consumed by fs, incl. metadata */
        __le32  fsBlockSize;
        __le32  fsFragSize;
        __le32  fsMaxExtendSize;
        __le32  fsSpaceUnits;
        __le32  fsMaxNumFiles;
        __le32  fsNumFreeFiles;
        __le32  fsInodeDensity;
};      /* valid iff ObjType == FT_FILESYS && !(ContentState & FSCS_NOTCLEAN) */

struct  aac_blockdevinfo {
        __le32  block_size;
        __le32  logical_phys_map;
        u8      identifier[16];
};

union aac_contentinfo {
        struct  aac_fsinfo              filesys;
        struct  aac_blockdevinfo        bdevinfo;
};

/*
 *      Query for Container Configuration Status
 */

#define CT_GET_CONFIG_STATUS 147
struct aac_get_config_status {
        __le32          command;        /* VM_ContainerConfig */
        __le32          type;           /* CT_GET_CONFIG_STATUS */
        __le32          parm1;
        __le32          parm2;
        __le32          parm3;
        __le32          parm4;
        __le32          parm5;
        __le32          count;  /* sizeof(((struct aac_get_config_status_resp *)NULL)->data) */
};

#define CFACT_CONTINUE 0
#define CFACT_PAUSE    1
#define CFACT_ABORT    2
struct aac_get_config_status_resp {
        __le32          response; /* ST_OK */
        __le32          dummy0;
        __le32          status; /* CT_OK */
        __le32          parm1;
        __le32          parm2;
        __le32          parm3;
        __le32          parm4;
        __le32          parm5;
        struct {
                __le32  action; /* CFACT_CONTINUE, CFACT_PAUSE or CFACT_ABORT */
                __le16  flags;
                __le16  count;
        }               data;
};

/*
 *      Accept the configuration as-is
 */

#define CT_COMMIT_CONFIG 152

struct aac_commit_config {
        __le32          command;        /* VM_ContainerConfig */
        __le32          type;           /* CT_COMMIT_CONFIG */
};

/*
 *      Query for Container Configuration Status
 */

#define CT_GET_CONTAINER_COUNT 4
struct aac_get_container_count {
        __le32          command;        /* VM_ContainerConfig */
        __le32          type;           /* CT_GET_CONTAINER_COUNT */
};

struct aac_get_container_count_resp {
        __le32          response; /* ST_OK */
        __le32          dummy0;
        __le32          MaxContainers;
        __le32          ContainerSwitchEntries;
        __le32          MaxPartitions;
        __le32          MaxSimpleVolumes;
};


/*
 *      Query for "mountable" objects, ie, objects that are typically
 *      associated with a drive letter on the client (host) side.
 */

struct aac_mntent {
        __le32                  oid;
        u8                      name[16];       /* if applicable */
        struct creation_info    create_info;    /* if applicable */
        __le32                  capacity;
        __le32                  vol;            /* substrate structure */
        __le32                  obj;            /* FT_FILESYS, etc. */
        __le32                  state;          /* unready for mounting,
                                                   readonly, etc. */
        union aac_contentinfo   fileinfo;       /* Info specific to content
                                                   manager (eg, filesystem) */
        __le32                  altoid;         /* != oid <==> snapshot or
                                                   broken mirror exists */
        __le32                  capacityhigh;
};

#define FSCS_NOTCLEAN   0x0001  /* fsck is necessary before mounting */
#define FSCS_READONLY   0x0002  /* possible result of broken mirror */
#define FSCS_HIDDEN     0x0004  /* should be ignored - set during a clear */
#define FSCS_NOT_READY  0x0008  /* Array spinning up to fulfil request */

struct aac_query_mount {
        __le32          command;
        __le32          type;
        __le32          count;
};

struct aac_mount {
        __le32          status;
        __le32          type;           /* should be same as that requested */
        __le32          count;
        struct aac_mntent mnt[1];
};

#define CT_READ_NAME 130
struct aac_get_name {
        __le32          command;        /* VM_ContainerConfig */
        __le32          type;           /* CT_READ_NAME */
        __le32          cid;
        __le32          parm1;
        __le32          parm2;
        __le32          parm3;
        __le32          parm4;
        __le32          count;  /* sizeof(((struct aac_get_name_resp *)NULL)->data) */
};

struct aac_get_name_resp {
        __le32          dummy0;
        __le32          dummy1;
        __le32          status; /* CT_OK */
        __le32          parm1;
        __le32          parm2;
        __le32          parm3;
        __le32          parm4;
        __le32          parm5;
        u8              data[17];
};

#define CT_CID_TO_32BITS_UID 165
struct aac_get_serial {
        __le32          command;        /* VM_ContainerConfig */
        __le32          type;           /* CT_CID_TO_32BITS_UID */
        __le32          cid;
};

struct aac_get_serial_resp {
        __le32          dummy0;
        __le32          dummy1;
        __le32          status; /* CT_OK */
        __le32          uid;
};

/*
 * The following command is sent to shut down each container.
 */

struct aac_close {
        __le32  command;
        __le32  cid;
};

struct aac_query_disk
{
        s32     cnum;
        s32     bus;
        s32     id;
        s32     lun;
        u32     valid;
        u32     locked;
        u32     deleted;
        s32     instance;
        s8      name[10];
        u32     unmapped;
};

struct aac_delete_disk {
        u32     disknum;
        u32     cnum;
};

struct fib_ioctl
{
        u32     fibctx;
        s32     wait;
        char    __user *fib;
};

struct revision
{
        u32 compat;
        __le32 version;
        __le32 build;
};


/*
 *      Ugly - non Linux like ioctl coding for back compat.
 */

#define CTL_CODE(function, method) (                 \
    (4<< 16) | ((function) << 2) | (method) \
)

/*
 *      Define the method codes for how buffers are passed for I/O and FS
 *      controls
 */

#define METHOD_BUFFERED                 0
#define METHOD_NEITHER                  3

/*
 *      Filesystem ioctls
 */

#define FSACTL_SENDFIB                          CTL_CODE(2050, METHOD_BUFFERED)
#define FSACTL_SEND_RAW_SRB                     CTL_CODE(2067, METHOD_BUFFERED)
#define FSACTL_DELETE_DISK                      0x163
#define FSACTL_QUERY_DISK                       0x173
#define FSACTL_OPEN_GET_ADAPTER_FIB             CTL_CODE(2100, METHOD_BUFFERED)
#define FSACTL_GET_NEXT_ADAPTER_FIB             CTL_CODE(2101, METHOD_BUFFERED)
#define FSACTL_CLOSE_GET_ADAPTER_FIB            CTL_CODE(2102, METHOD_BUFFERED)
#define FSACTL_MINIPORT_REV_CHECK               CTL_CODE(2107, METHOD_BUFFERED)
#define FSACTL_GET_PCI_INFO                     CTL_CODE(2119, METHOD_BUFFERED)
#define FSACTL_FORCE_DELETE_DISK                CTL_CODE(2120, METHOD_NEITHER)
#define FSACTL_GET_CONTAINERS                   2131
#define FSACTL_SEND_LARGE_FIB                   CTL_CODE(2138, METHOD_BUFFERED)
#define FSACTL_RESET_IOP                        CTL_CODE(2140, METHOD_BUFFERED)
#define FSACTL_GET_HBA_INFO                     CTL_CODE(2150, METHOD_BUFFERED)
/* flags defined for IOP & HW SOFT RESET */
#define HW_IOP_RESET                            0x01
#define HW_SOFT_RESET                           0x02
#define IOP_HWSOFT_RESET                        (HW_IOP_RESET | HW_SOFT_RESET)
/* HW Soft Reset register offset */
#define IBW_SWR_OFFSET                          0x4000
#define SOFT_RESET_TIME                 60



struct aac_common
{
        /*
         *      If this value is set to 1 then interrupt moderation will occur
         *      in the base commuication support.
         */
        u32 irq_mod;
        u32 peak_fibs;
        u32 zero_fibs;
        u32 fib_timeouts;
        /*
         *      Statistical counters in debug mode
         */
#ifdef DBG
        u32 FibsSent;
        u32 FibRecved;
        u32 NativeSent;
        u32 NativeRecved;
        u32 NoResponseSent;
        u32 NoResponseRecved;
        u32 AsyncSent;
        u32 AsyncRecved;
        u32 NormalSent;
        u32 NormalRecved;
#endif
};

extern struct aac_common aac_config;

/*
 * This is for management ioctl purpose only.
 */
struct aac_hba_info {

        u8      driver_name[50];
        u8      adapter_number;
        u8      system_io_bus_number;
        u8      device_number;
        u32     function_number;
        u32     vendor_id;
        u32     device_id;
        u32     sub_vendor_id;
        u32     sub_system_id;
        u32     mapped_base_address_size;
        u32     base_physical_address_high_part;
        u32     base_physical_address_low_part;

        u32     max_command_size;
        u32     max_fib_size;
        u32     max_scatter_gather_from_os;
        u32     max_scatter_gather_to_fw;
        u32     max_outstanding_fibs;

        u32     queue_start_threshold;
        u32     queue_dump_threshold;
        u32     max_io_size_queued;
        u32     outstanding_io;

        u32     firmware_build_number;
        u32     bios_build_number;
        u32     driver_build_number;
        u32     serial_number_high_part;
        u32     serial_number_low_part;
        u32     supported_options;
        u32     feature_bits;
        u32     currentnumber_ports;

        u8      new_comm_interface:1;
        u8      new_commands_supported:1;
        u8      disable_passthrough:1;
        u8      expose_non_dasd:1;
        u8      queue_allowed:1;
        u8      bled_check_enabled:1;
        u8      reserved1:1;
        u8      reserted2:1;

        u32     reserved3[10];

};

/*
 *      The following macro is used when sending and receiving FIBs. It is
 *      only used for debugging.
 */

#ifdef DBG
#define FIB_COUNTER_INCREMENT(counter)          (counter)++
#else
#define FIB_COUNTER_INCREMENT(counter)
#endif

/*
 *      Adapter direct commands
 *      Monitor/Kernel API
 */

#define BREAKPOINT_REQUEST              0x00000004
#define INIT_STRUCT_BASE_ADDRESS        0x00000005
#define READ_PERMANENT_PARAMETERS       0x0000000a
#define WRITE_PERMANENT_PARAMETERS      0x0000000b
#define HOST_CRASHING                   0x0000000d
#define SEND_SYNCHRONOUS_FIB            0x0000000c
#define COMMAND_POST_RESULTS            0x00000014
#define GET_ADAPTER_PROPERTIES          0x00000019
#define GET_DRIVER_BUFFER_PROPERTIES    0x00000023
#define RCV_TEMP_READINGS               0x00000025
#define GET_COMM_PREFERRED_SETTINGS     0x00000026
#define IOP_RESET_FW_FIB_DUMP           0x00000034
#define DROP_IO                 0x00000035
#define IOP_RESET                       0x00001000
#define IOP_RESET_ALWAYS                0x00001001
#define RE_INIT_ADAPTER         0x000000ee

#define IOP_SRC_RESET_MASK              0x00000100

/*
 *      Adapter Status Register
 *
 *  Phase Staus mailbox is 32bits:
 *      <31:16> = Phase Status
 *      <15:0>  = Phase
 *
 *      The adapter reports is present state through the phase.  Only
 *      a single phase should be ever be set.  Each phase can have multiple
 *      phase status bits to provide more detailed information about the
 *      state of the board.  Care should be taken to ensure that any phase
 *      status bits that are set when changing the phase are also valid
 *      for the new phase or be cleared out.  Adapter software (monitor,
 *      iflash, kernel) is responsible for properly maintining the phase
 *      status mailbox when it is running.
 *
 *      MONKER_API Phases
 *
 *      Phases are bit oriented.  It is NOT valid  to have multiple bits set
 */

#define SELF_TEST_FAILED                0x00000004
#define MONITOR_PANIC                   0x00000020
#define KERNEL_BOOTING                  0x00000040
#define KERNEL_UP_AND_RUNNING           0x00000080
#define KERNEL_PANIC                    0x00000100
#define FLASH_UPD_PENDING               0x00002000
#define FLASH_UPD_SUCCESS               0x00004000
#define FLASH_UPD_FAILED                0x00008000
#define INVALID_OMR                     0xffffffff
#define FWUPD_TIMEOUT                   (5 * 60)

/*
 *      Doorbell bit defines
 */

#define DoorBellSyncCmdAvailable        (1<<0)  /* Host -> Adapter */
#define DoorBellPrintfDone              (1<<5)  /* Host -> Adapter */
#define DoorBellAdapterNormCmdReady     (1<<1)  /* Adapter -> Host */
#define DoorBellAdapterNormRespReady    (1<<2)  /* Adapter -> Host */
#define DoorBellAdapterNormCmdNotFull   (1<<3)  /* Adapter -> Host */
#define DoorBellAdapterNormRespNotFull  (1<<4)  /* Adapter -> Host */
#define DoorBellPrintfReady             (1<<5)  /* Adapter -> Host */
#define DoorBellAifPending              (1<<6)  /* Adapter -> Host */

/* PMC specific outbound doorbell bits */
#define PmDoorBellResponseSent          (1<<1)  /* Adapter -> Host */

/*
 *      For FIB communication, we need all of the following things
 *      to send back to the user.
 */

#define         AifCmdEventNotify       1       /* Notify of event */
#define                 AifEnConfigChange       3       /* Adapter configuration change */
#define                 AifEnContainerChange    4       /* Container configuration change */
#define                 AifEnDeviceFailure      5       /* SCSI device failed */
#define                 AifEnEnclosureManagement 13     /* EM_DRIVE_* */
#define                         EM_DRIVE_INSERTION      31
#define                         EM_DRIVE_REMOVAL        32
#define                 EM_SES_DRIVE_INSERTION  33
#define                 EM_SES_DRIVE_REMOVAL    26
#define                 AifEnBatteryEvent       14      /* Change in Battery State */
#define                 AifEnAddContainer       15      /* A new array was created */
#define                 AifEnDeleteContainer    16      /* A container was deleted */
#define                 AifEnExpEvent           23      /* Firmware Event Log */
#define                 AifExeFirmwarePanic     3       /* Firmware Event Panic */
#define                 AifHighPriority         3       /* Highest Priority Event */
#define                 AifEnAddJBOD            30      /* JBOD created */
#define                 AifEnDeleteJBOD         31      /* JBOD deleted */

#define                 AifBuManagerEvent               42 /* Bu management*/
#define                 AifBuCacheDataLoss              10
#define                 AifBuCacheDataRecover   11

#define         AifCmdJobProgress       2       /* Progress report */
#define                 AifJobCtrZero   101     /* Array Zero progress */
#define                 AifJobStsSuccess 1      /* Job completes */
#define                 AifJobStsRunning 102    /* Job running */
#define         AifCmdAPIReport         3       /* Report from other user of API */
#define         AifCmdDriverNotify      4       /* Notify host driver of event */
#define                 AifDenMorphComplete 200 /* A morph operation completed */
#define                 AifDenVolumeExtendComplete 201 /* A volume extend completed */
#define         AifReqJobList           100     /* Gets back complete job list */
#define         AifReqJobsForCtr        101     /* Gets back jobs for specific container */
#define         AifReqJobsForScsi       102     /* Gets back jobs for specific SCSI device */
#define         AifReqJobReport         103     /* Gets back a specific job report or list of them */
#define         AifReqTerminateJob      104     /* Terminates job */
#define         AifReqSuspendJob        105     /* Suspends a job */
#define         AifReqResumeJob         106     /* Resumes a job */
#define         AifReqSendAPIReport     107     /* API generic report requests */
#define         AifReqAPIJobStart       108     /* Start a job from the API */
#define         AifReqAPIJobUpdate      109     /* Update a job report from the API */
#define         AifReqAPIJobFinish      110     /* Finish a job from the API */

/* PMC NEW COMM: Request the event data */
#define         AifReqEvent             200
#define         AifRawDeviceRemove      203     /* RAW device deleted */
#define         AifNativeDeviceAdd      204     /* native HBA device added */
#define         AifNativeDeviceRemove   205     /* native HBA device removed */


/*
 *      Adapter Initiated FIB command structures. Start with the adapter
 *      initiated FIBs that really come from the adapter, and get responded
 *      to by the host.
 */

struct aac_aifcmd {
        __le32 command;         /* Tell host what type of notify this is */
        __le32 seqnum;          /* To allow ordering of reports (if necessary) */
        u8 data[1];             /* Undefined length (from kernel viewpoint) */
};

/**
 *      Convert capacity to cylinders
 *      accounting for the fact capacity could be a 64 bit value
 *
 */
static inline unsigned int cap_to_cyls(sector_t capacity, unsigned divisor)
{
        sector_div(capacity, divisor);
        return capacity;
}

static inline int aac_pci_offline(struct aac_dev *dev)
{
        return pci_channel_offline(dev->pdev) || dev->handle_pci_error;
}

static inline int aac_adapter_check_health(struct aac_dev *dev)
{
        if (unlikely(aac_pci_offline(dev)))
                return -1;

        return (dev)->a_ops.adapter_check_health(dev);
}


int aac_scan_host(struct aac_dev *dev);

static inline void aac_schedule_safw_scan_worker(struct aac_dev *dev)
{
        schedule_delayed_work(&dev->safw_rescan_work, AAC_RESCAN_DELAY);
}

static inline void aac_schedule_src_reinit_aif_worker(struct aac_dev *dev)
{
        schedule_delayed_work(&dev->src_reinit_aif_worker, AAC_RESCAN_DELAY);
}

static inline void aac_safw_rescan_worker(struct work_struct *work)
{
        struct aac_dev *dev = container_of(to_delayed_work(work),
                struct aac_dev, safw_rescan_work);

        wait_event(dev->scsi_host_ptr->host_wait,
                !scsi_host_in_recovery(dev->scsi_host_ptr));

        aac_scan_host(dev);
}

static inline void aac_cancel_rescan_worker(struct aac_dev *dev)
{
        cancel_delayed_work_sync(&dev->safw_rescan_work);
        cancel_delayed_work_sync(&dev->src_reinit_aif_worker);
}

/* SCp.phase values */
#define AAC_OWNER_MIDLEVEL      0x101
#define AAC_OWNER_LOWLEVEL      0x102
#define AAC_OWNER_ERROR_HANDLER 0x103
#define AAC_OWNER_FIRMWARE      0x106

void aac_safw_rescan_worker(struct work_struct *work);
void aac_src_reinit_aif_worker(struct work_struct *work);
int aac_acquire_irq(struct aac_dev *dev);
void aac_free_irq(struct aac_dev *dev);
int aac_setup_safw_adapter(struct aac_dev *dev);
const char *aac_driverinfo(struct Scsi_Host *);
void aac_fib_vector_assign(struct aac_dev *dev);
struct fib *aac_fib_alloc(struct aac_dev *dev);
struct fib *aac_fib_alloc_tag(struct aac_dev *dev, struct scsi_cmnd *scmd);
int aac_fib_setup(struct aac_dev *dev);
void aac_fib_map_free(struct aac_dev *dev);
void aac_fib_free(struct fib * context);
void aac_fib_init(struct fib * context);
void aac_printf(struct aac_dev *dev, u32 val);
int aac_fib_send(u16 command, struct fib * context, unsigned long size, int priority, int wait, int reply, fib_callback callback, void *ctxt);
int aac_hba_send(u8 command, struct fib *context,
                fib_callback callback, void *ctxt);
int aac_consumer_get(struct aac_dev * dev, struct aac_queue * q, struct aac_entry **entry);
void aac_consumer_free(struct aac_dev * dev, struct aac_queue * q, u32 qnum);
int aac_fib_complete(struct fib * context);
void aac_hba_callback(void *context, struct fib *fibptr);
#define fib_data(fibctx) ((void *)(fibctx)->hw_fib_va->data)
struct aac_dev *aac_init_adapter(struct aac_dev *dev);
void aac_src_access_devreg(struct aac_dev *dev, int mode);
void aac_set_intx_mode(struct aac_dev *dev);
int aac_get_config_status(struct aac_dev *dev, int commit_flag);
int aac_get_containers(struct aac_dev *dev);
int aac_scsi_cmd(struct scsi_cmnd *cmd);
int aac_dev_ioctl(struct aac_dev *dev, unsigned int cmd, void __user *arg);
#ifndef shost_to_class
#define shost_to_class(shost) &shost->shost_dev
#endif
ssize_t aac_get_serial_number(struct device *dev, char *buf);
int aac_do_ioctl(struct aac_dev *dev, unsigned int cmd, void __user *arg);
int aac_rx_init(struct aac_dev *dev);
int aac_rkt_init(struct aac_dev *dev);
int aac_nark_init(struct aac_dev *dev);
int aac_sa_init(struct aac_dev *dev);
int aac_src_init(struct aac_dev *dev);
int aac_srcv_init(struct aac_dev *dev);
int aac_queue_get(struct aac_dev * dev, u32 * index, u32 qid, struct hw_fib * hw_fib, int wait, struct fib * fibptr, unsigned long *nonotify);
void aac_define_int_mode(struct aac_dev *dev);
unsigned int aac_response_normal(struct aac_queue * q);
unsigned int aac_command_normal(struct aac_queue * q);
unsigned int aac_intr_normal(struct aac_dev *dev, u32 Index,
                        int isAif, int isFastResponse,
                        struct hw_fib *aif_fib);
int aac_reset_adapter(struct aac_dev *dev, int forced, u8 reset_type);
int aac_check_health(struct aac_dev * dev);
int aac_command_thread(void *data);
int aac_close_fib_context(struct aac_dev * dev, struct aac_fib_context *fibctx);
int aac_fib_adapter_complete(struct fib * fibptr, unsigned short size);
struct aac_driver_ident* aac_get_driver_ident(int devtype);
int aac_get_adapter_info(struct aac_dev* dev);
int aac_send_shutdown(struct aac_dev *dev);
int aac_probe_container(struct aac_dev *dev, int cid);
int _aac_rx_init(struct aac_dev *dev);
int aac_rx_select_comm(struct aac_dev *dev, int comm);
int aac_rx_deliver_producer(struct fib * fib);
void aac_reinit_aif(struct aac_dev *aac, unsigned int index);

static inline int aac_is_src(struct aac_dev *dev)
{
        u16 device = dev->pdev->device;

        if (device == PMC_DEVICE_S6 ||
                device == PMC_DEVICE_S7 ||
                device == PMC_DEVICE_S8)
                return 1;
        return 0;
}

static inline int aac_supports_2T(struct aac_dev *dev)
{
        return (dev->adapter_info.options & AAC_OPT_NEW_COMM_64);
}

char * get_container_type(unsigned type);
extern int numacb;
extern char aac_driver_version[];
extern int startup_timeout;
extern int aif_timeout;
extern int expose_physicals;
extern int aac_reset_devices;
extern int aac_msi;
extern int aac_commit;
extern int update_interval;
extern int check_interval;
extern int aac_check_reset;
extern int aac_fib_dump;
#endif