linux/drivers/tty/serial/8250/serial_cs.c
<<
>>
Prefs
   1// SPDX-License-Identifier: (GPL-2.0 OR MPL-1.1)
   2/*======================================================================
   3
   4    A driver for PCMCIA serial devices
   5
   6    serial_cs.c 1.134 2002/05/04 05:48:53
   7
   8    The contents of this file are subject to the Mozilla Public
   9    License Version 1.1 (the "License"); you may not use this file
  10    except in compliance with the License. You may obtain a copy of
  11    the License at http://www.mozilla.org/MPL/
  12
  13    Software distributed under the License is distributed on an "AS
  14    IS" basis, WITHOUT WARRANTY OF ANY KIND, either express or
  15    implied. See the License for the specific language governing
  16    rights and limitations under the License.
  17
  18    The initial developer of the original code is David A. Hinds
  19    <dahinds@users.sourceforge.net>.  Portions created by David A. Hinds
  20    are Copyright (C) 1999 David A. Hinds.  All Rights Reserved.
  21
  22    Alternatively, the contents of this file may be used under the
  23    terms of the GNU General Public License version 2 (the "GPL"), in which
  24    case the provisions of the GPL are applicable instead of the
  25    above.  If you wish to allow the use of your version of this file
  26    only under the terms of the GPL and not to allow others to use
  27    your version of this file under the MPL, indicate your decision
  28    by deleting the provisions above and replace them with the notice
  29    and other provisions required by the GPL.  If you do not delete
  30    the provisions above, a recipient may use your version of this
  31    file under either the MPL or the GPL.
  32
  33======================================================================*/
  34
  35#include <linux/module.h>
  36#include <linux/moduleparam.h>
  37#include <linux/kernel.h>
  38#include <linux/ptrace.h>
  39#include <linux/slab.h>
  40#include <linux/string.h>
  41#include <linux/timer.h>
  42#include <linux/serial_core.h>
  43#include <linux/delay.h>
  44#include <linux/major.h>
  45#include <asm/io.h>
  46
  47#include <pcmcia/cistpl.h>
  48#include <pcmcia/ciscode.h>
  49#include <pcmcia/ds.h>
  50#include <pcmcia/cisreg.h>
  51
  52#include "8250.h"
  53
  54
  55/*====================================================================*/
  56
  57/* Parameters that can be set with 'insmod' */
  58
  59/* Enable the speaker? */
  60static int do_sound = 1;
  61/* Skip strict UART tests? */
  62static int buggy_uart;
  63
  64module_param(do_sound, int, 0444);
  65module_param(buggy_uart, int, 0444);
  66
  67/*====================================================================*/
  68
  69/* Table of multi-port card ID's */
  70
  71struct serial_quirk {
  72        unsigned int manfid;
  73        unsigned int prodid;
  74        int multi;              /* 1 = multifunction, > 1 = # ports */
  75        void (*config)(struct pcmcia_device *);
  76        void (*setup)(struct pcmcia_device *, struct uart_8250_port *);
  77        void (*wakeup)(struct pcmcia_device *);
  78        int (*post)(struct pcmcia_device *);
  79};
  80
  81struct serial_info {
  82        struct pcmcia_device    *p_dev;
  83        int                     ndev;
  84        int                     multi;
  85        int                     slave;
  86        int                     manfid;
  87        int                     prodid;
  88        int                     c950ctrl;
  89        int                     line[4];
  90        const struct serial_quirk *quirk;
  91};
  92
  93struct serial_cfg_mem {
  94        tuple_t tuple;
  95        cisparse_t parse;
  96        u_char buf[256];
  97};
  98
  99/*
 100 * vers_1 5.0, "Brain Boxes", "2-Port RS232 card", "r6"
 101 * manfid 0x0160, 0x0104
 102 * This card appears to have a 14.7456MHz clock.
 103 */
 104/* Generic Modem: MD55x (GPRS/EDGE) have
 105 * Elan VPU16551 UART with 14.7456MHz oscillator
 106 * manfid 0x015D, 0x4C45
 107 */
 108static void quirk_setup_brainboxes_0104(struct pcmcia_device *link, struct uart_8250_port *uart)
 109{
 110        uart->port.uartclk = 14745600;
 111}
 112
 113static int quirk_post_ibm(struct pcmcia_device *link)
 114{
 115        u8 val;
 116        int ret;
 117
 118        ret = pcmcia_read_config_byte(link, 0x800, &val);
 119        if (ret)
 120                goto failed;
 121
 122        ret = pcmcia_write_config_byte(link, 0x800, val | 1);
 123        if (ret)
 124                goto failed;
 125        return 0;
 126
 127 failed:
 128        return -ENODEV;
 129}
 130
 131/*
 132 * Nokia cards are not really multiport cards.  Shouldn't this
 133 * be handled by setting the quirk entry .multi = 0 | 1 ?
 134 */
 135static void quirk_config_nokia(struct pcmcia_device *link)
 136{
 137        struct serial_info *info = link->priv;
 138
 139        if (info->multi > 1)
 140                info->multi = 1;
 141}
 142
 143static void quirk_wakeup_oxsemi(struct pcmcia_device *link)
 144{
 145        struct serial_info *info = link->priv;
 146
 147        if (info->c950ctrl)
 148                outb(12, info->c950ctrl + 1);
 149}
 150
 151/* request_region? oxsemi branch does no request_region too... */
 152/*
 153 * This sequence is needed to properly initialize MC45 attached to OXCF950.
 154 * I tried decreasing these msleep()s, but it worked properly (survived
 155 * 1000 stop/start operations) with these timeouts (or bigger).
 156 */
 157static void quirk_wakeup_possio_gcc(struct pcmcia_device *link)
 158{
 159        struct serial_info *info = link->priv;
 160        unsigned int ctrl = info->c950ctrl;
 161
 162        outb(0xA, ctrl + 1);
 163        msleep(100);
 164        outb(0xE, ctrl + 1);
 165        msleep(300);
 166        outb(0xC, ctrl + 1);
 167        msleep(100);
 168        outb(0xE, ctrl + 1);
 169        msleep(200);
 170        outb(0xF, ctrl + 1);
 171        msleep(100);
 172        outb(0xE, ctrl + 1);
 173        msleep(100);
 174        outb(0xC, ctrl + 1);
 175}
 176
 177/*
 178 * Socket Dual IO: this enables irq's for second port
 179 */
 180static void quirk_config_socket(struct pcmcia_device *link)
 181{
 182        struct serial_info *info = link->priv;
 183
 184        if (info->multi)
 185                link->config_flags |= CONF_ENABLE_ESR;
 186}
 187
 188static const struct serial_quirk quirks[] = {
 189        {
 190                .manfid = 0x0160,
 191                .prodid = 0x0104,
 192                .multi  = -1,
 193                .setup  = quirk_setup_brainboxes_0104,
 194        }, {
 195                .manfid = 0x015D,
 196                .prodid = 0x4C45,
 197                .multi  = -1,
 198                .setup  = quirk_setup_brainboxes_0104,
 199        }, {
 200                .manfid = MANFID_IBM,
 201                .prodid = ~0,
 202                .multi  = -1,
 203                .post   = quirk_post_ibm,
 204        }, {
 205                .manfid = MANFID_INTEL,
 206                .prodid = PRODID_INTEL_DUAL_RS232,
 207                .multi  = 2,
 208        }, {
 209                .manfid = MANFID_NATINST,
 210                .prodid = PRODID_NATINST_QUAD_RS232,
 211                .multi  = 4,
 212        }, {
 213                .manfid = MANFID_NOKIA,
 214                .prodid = ~0,
 215                .multi  = -1,
 216                .config = quirk_config_nokia,
 217        }, {
 218                .manfid = MANFID_OMEGA,
 219                .prodid = PRODID_OMEGA_QSP_100,
 220                .multi  = 4,
 221        }, {
 222                .manfid = MANFID_OXSEMI,
 223                .prodid = ~0,
 224                .multi  = -1,
 225                .wakeup = quirk_wakeup_oxsemi,
 226        }, {
 227                .manfid = MANFID_POSSIO,
 228                .prodid = PRODID_POSSIO_GCC,
 229                .multi  = -1,
 230                .wakeup = quirk_wakeup_possio_gcc,
 231        }, {
 232                .manfid = MANFID_QUATECH,
 233                .prodid = PRODID_QUATECH_DUAL_RS232,
 234                .multi  = 2,
 235        }, {
 236                .manfid = MANFID_QUATECH,
 237                .prodid = PRODID_QUATECH_DUAL_RS232_D1,
 238                .multi  = 2,
 239        }, {
 240                .manfid = MANFID_QUATECH,
 241                .prodid = PRODID_QUATECH_DUAL_RS232_G,
 242                .multi  = 2,
 243        }, {
 244                .manfid = MANFID_QUATECH,
 245                .prodid = PRODID_QUATECH_QUAD_RS232,
 246                .multi  = 4,
 247        }, {
 248                .manfid = MANFID_SOCKET,
 249                .prodid = PRODID_SOCKET_DUAL_RS232,
 250                .multi  = 2,
 251                .config = quirk_config_socket,
 252        }, {
 253                .manfid = MANFID_SOCKET,
 254                .prodid = ~0,
 255                .multi  = -1,
 256                .config = quirk_config_socket,
 257        }
 258};
 259
 260
 261static int serial_config(struct pcmcia_device *link);
 262
 263
 264static void serial_remove(struct pcmcia_device *link)
 265{
 266        struct serial_info *info = link->priv;
 267        int i;
 268
 269        dev_dbg(&link->dev, "serial_release\n");
 270
 271        /*
 272         * Recheck to see if the device is still configured.
 273         */
 274        for (i = 0; i < info->ndev; i++)
 275                serial8250_unregister_port(info->line[i]);
 276
 277        if (!info->slave)
 278                pcmcia_disable_device(link);
 279}
 280
 281static int serial_suspend(struct pcmcia_device *link)
 282{
 283        struct serial_info *info = link->priv;
 284        int i;
 285
 286        for (i = 0; i < info->ndev; i++)
 287                serial8250_suspend_port(info->line[i]);
 288
 289        return 0;
 290}
 291
 292static int serial_resume(struct pcmcia_device *link)
 293{
 294        struct serial_info *info = link->priv;
 295        int i;
 296
 297        for (i = 0; i < info->ndev; i++)
 298                serial8250_resume_port(info->line[i]);
 299
 300        if (info->quirk && info->quirk->wakeup)
 301                info->quirk->wakeup(link);
 302
 303        return 0;
 304}
 305
 306static int serial_probe(struct pcmcia_device *link)
 307{
 308        struct serial_info *info;
 309        int ret;
 310
 311        dev_dbg(&link->dev, "serial_attach()\n");
 312
 313        /* Create new serial device */
 314        info = kzalloc(sizeof(*info), GFP_KERNEL);
 315        if (!info)
 316                return -ENOMEM;
 317        info->p_dev = link;
 318        link->priv = info;
 319
 320        link->config_flags |= CONF_ENABLE_IRQ | CONF_AUTO_SET_IO;
 321        if (do_sound)
 322                link->config_flags |= CONF_ENABLE_SPKR;
 323
 324        ret = serial_config(link);
 325        if (ret)
 326                goto free_info;
 327
 328        return 0;
 329
 330free_info:
 331        kfree(info);
 332        return ret;
 333}
 334
 335static void serial_detach(struct pcmcia_device *link)
 336{
 337        struct serial_info *info = link->priv;
 338
 339        dev_dbg(&link->dev, "serial_detach\n");
 340
 341        /*
 342         * Ensure that the ports have been released.
 343         */
 344        serial_remove(link);
 345
 346        /* free bits */
 347        kfree(info);
 348}
 349
 350/*====================================================================*/
 351
 352static int setup_serial(struct pcmcia_device *handle, struct serial_info *info,
 353                        unsigned int iobase, int irq)
 354{
 355        struct uart_8250_port uart;
 356        int line;
 357
 358        memset(&uart, 0, sizeof(uart));
 359        uart.port.iobase = iobase;
 360        uart.port.irq = irq;
 361        uart.port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_SHARE_IRQ;
 362        uart.port.uartclk = 1843200;
 363        uart.port.dev = &handle->dev;
 364        if (buggy_uart)
 365                uart.port.flags |= UPF_BUGGY_UART;
 366
 367        if (info->quirk && info->quirk->setup)
 368                info->quirk->setup(handle, &uart);
 369
 370        line = serial8250_register_8250_port(&uart);
 371        if (line < 0) {
 372                pr_err("serial_cs: serial8250_register_8250_port() at 0x%04lx, irq %d failed\n",
 373                                                        (unsigned long)iobase, irq);
 374                return -EINVAL;
 375        }
 376
 377        info->line[info->ndev] = line;
 378        info->ndev++;
 379
 380        return 0;
 381}
 382
 383/*====================================================================*/
 384
 385static int pfc_config(struct pcmcia_device *p_dev)
 386{
 387        unsigned int port = 0;
 388        struct serial_info *info = p_dev->priv;
 389
 390        if ((p_dev->resource[1]->end != 0) &&
 391                (resource_size(p_dev->resource[1]) == 8)) {
 392                port = p_dev->resource[1]->start;
 393                info->slave = 1;
 394        } else if ((info->manfid == MANFID_OSITECH) &&
 395                (resource_size(p_dev->resource[0]) == 0x40)) {
 396                port = p_dev->resource[0]->start + 0x28;
 397                info->slave = 1;
 398        }
 399        if (info->slave)
 400                return setup_serial(p_dev, info, port, p_dev->irq);
 401
 402        dev_warn(&p_dev->dev, "no usable port range found, giving up\n");
 403        return -ENODEV;
 404}
 405
 406static int simple_config_check(struct pcmcia_device *p_dev, void *priv_data)
 407{
 408        static const int size_table[2] = { 8, 16 };
 409        int *try = priv_data;
 410
 411        if (p_dev->resource[0]->start == 0)
 412                return -ENODEV;
 413
 414        if ((*try & 0x1) == 0)
 415                p_dev->io_lines = 16;
 416
 417        if (p_dev->resource[0]->end != size_table[(*try >> 1)])
 418                return -ENODEV;
 419
 420        p_dev->resource[0]->end = 8;
 421        p_dev->resource[0]->flags &= ~IO_DATA_PATH_WIDTH;
 422        p_dev->resource[0]->flags |= IO_DATA_PATH_WIDTH_8;
 423
 424        return pcmcia_request_io(p_dev);
 425}
 426
 427static int simple_config_check_notpicky(struct pcmcia_device *p_dev,
 428                                        void *priv_data)
 429{
 430        static const unsigned int base[5] = { 0x3f8, 0x2f8, 0x3e8, 0x2e8, 0x0 };
 431        int j;
 432
 433        if (p_dev->io_lines > 3)
 434                return -ENODEV;
 435
 436        p_dev->resource[0]->flags &= ~IO_DATA_PATH_WIDTH;
 437        p_dev->resource[0]->flags |= IO_DATA_PATH_WIDTH_8;
 438        p_dev->resource[0]->end = 8;
 439
 440        for (j = 0; j < 5; j++) {
 441                p_dev->resource[0]->start = base[j];
 442                p_dev->io_lines = base[j] ? 16 : 3;
 443                if (!pcmcia_request_io(p_dev))
 444                        return 0;
 445        }
 446        return -ENODEV;
 447}
 448
 449static int simple_config(struct pcmcia_device *link)
 450{
 451        struct serial_info *info = link->priv;
 452        int ret, try;
 453
 454        /*
 455         * First pass: look for a config entry that looks normal.
 456         * Two tries: without IO aliases, then with aliases.
 457         */
 458        link->config_flags |= CONF_AUTO_SET_VPP;
 459        for (try = 0; try < 4; try++)
 460                if (!pcmcia_loop_config(link, simple_config_check, &try))
 461                        goto found_port;
 462
 463        /*
 464         * Second pass: try to find an entry that isn't picky about
 465         * its base address, then try to grab any standard serial port
 466         * address, and finally try to get any free port.
 467         */
 468        ret = pcmcia_loop_config(link, simple_config_check_notpicky, NULL);
 469        if (ret) {
 470                dev_warn(&link->dev, "no usable port range found, giving up\n");
 471                return ret;
 472        }
 473
 474found_port:
 475        if (info->multi && (info->manfid == MANFID_3COM))
 476                link->config_index &= ~(0x08);
 477
 478        /*
 479         * Apply any configuration quirks.
 480         */
 481        if (info->quirk && info->quirk->config)
 482                info->quirk->config(link);
 483
 484        ret = pcmcia_enable_device(link);
 485        if (ret != 0)
 486                return ret;
 487        return setup_serial(link, info, link->resource[0]->start, link->irq);
 488}
 489
 490static int multi_config_check(struct pcmcia_device *p_dev, void *priv_data)
 491{
 492        int *multi = priv_data;
 493
 494        if (p_dev->resource[1]->end)
 495                return -EINVAL;
 496
 497        /*
 498         * The quad port cards have bad CIS's, so just look for a
 499         * window larger than 8 ports and assume it will be right.
 500         */
 501        if (p_dev->resource[0]->end <= 8)
 502                return -EINVAL;
 503
 504        p_dev->resource[0]->flags &= ~IO_DATA_PATH_WIDTH;
 505        p_dev->resource[0]->flags |= IO_DATA_PATH_WIDTH_8;
 506        p_dev->resource[0]->end = *multi * 8;
 507
 508        if (pcmcia_request_io(p_dev))
 509                return -ENODEV;
 510        return 0;
 511}
 512
 513static int multi_config_check_notpicky(struct pcmcia_device *p_dev,
 514                                       void *priv_data)
 515{
 516        int *base2 = priv_data;
 517
 518        if (!p_dev->resource[0]->end || !p_dev->resource[1]->end ||
 519                p_dev->resource[0]->start + 8 != p_dev->resource[1]->start)
 520                return -ENODEV;
 521
 522        p_dev->resource[0]->end = p_dev->resource[1]->end = 8;
 523        p_dev->resource[0]->flags &= ~IO_DATA_PATH_WIDTH;
 524        p_dev->resource[0]->flags |= IO_DATA_PATH_WIDTH_8;
 525
 526        if (pcmcia_request_io(p_dev))
 527                return -ENODEV;
 528
 529        *base2 = p_dev->resource[0]->start + 8;
 530        return 0;
 531}
 532
 533static int multi_config(struct pcmcia_device *link)
 534{
 535        struct serial_info *info = link->priv;
 536        int i, base2 = 0;
 537
 538        /* First, look for a generic full-sized window */
 539        if (!pcmcia_loop_config(link, multi_config_check, &info->multi))
 540                base2 = link->resource[0]->start + 8;
 541        else {
 542                /* If that didn't work, look for two windows */
 543                info->multi = 2;
 544                if (pcmcia_loop_config(link, multi_config_check_notpicky,
 545                                       &base2)) {
 546                        dev_warn(&link->dev,
 547                                 "no usable port range found, giving up\n");
 548                        return -ENODEV;
 549                }
 550        }
 551
 552        if (!link->irq)
 553                dev_warn(&link->dev, "no usable IRQ found, continuing...\n");
 554
 555        /*
 556         * Apply any configuration quirks.
 557         */
 558        if (info->quirk && info->quirk->config)
 559                info->quirk->config(link);
 560
 561        i = pcmcia_enable_device(link);
 562        if (i != 0)
 563                return -ENODEV;
 564
 565        /* The Oxford Semiconductor OXCF950 cards are in fact single-port:
 566         * 8 registers are for the UART, the others are extra registers.
 567         * Siemen's MC45 PCMCIA (Possio's GCC) is OXCF950 based too.
 568         */
 569        if (info->manfid == MANFID_OXSEMI || (info->manfid == MANFID_POSSIO &&
 570                                info->prodid == PRODID_POSSIO_GCC)) {
 571                if (link->config_index == 1 ||
 572                    link->config_index == 3) {
 573                        setup_serial(link, info, base2, link->irq);
 574                        base2 = link->resource[0]->start;
 575                } else {
 576                        setup_serial(link, info, link->resource[0]->start,
 577                                     link->irq);
 578                }
 579                info->c950ctrl = base2;
 580
 581                /*
 582                 * FIXME: We really should wake up the port prior to
 583                 * handing it over to the serial layer.
 584                 */
 585                if (info->quirk && info->quirk->wakeup)
 586                        info->quirk->wakeup(link);
 587
 588                return 0;
 589        }
 590
 591        setup_serial(link, info, link->resource[0]->start, link->irq);
 592        for (i = 0; i < info->multi - 1; i++)
 593                setup_serial(link, info, base2 + (8 * i),
 594                                link->irq);
 595        return 0;
 596}
 597
 598static int serial_check_for_multi(struct pcmcia_device *p_dev,  void *priv_data)
 599{
 600        struct serial_info *info = p_dev->priv;
 601
 602        if (!p_dev->resource[0]->end)
 603                return -EINVAL;
 604
 605        if ((!p_dev->resource[1]->end) && (p_dev->resource[0]->end % 8 == 0))
 606                info->multi = p_dev->resource[0]->end >> 3;
 607
 608        if ((p_dev->resource[1]->end) && (p_dev->resource[0]->end == 8)
 609                && (p_dev->resource[1]->end == 8))
 610                info->multi = 2;
 611
 612        return 0; /* break */
 613}
 614
 615
 616static int serial_config(struct pcmcia_device *link)
 617{
 618        struct serial_info *info = link->priv;
 619        int i;
 620
 621        dev_dbg(&link->dev, "serial_config\n");
 622
 623        /* Is this a compliant multifunction card? */
 624        info->multi = (link->socket->functions > 1);
 625
 626        /* Is this a multiport card? */
 627        info->manfid = link->manf_id;
 628        info->prodid = link->card_id;
 629
 630        for (i = 0; i < ARRAY_SIZE(quirks); i++)
 631                if ((quirks[i].manfid == ~0 ||
 632                     quirks[i].manfid == info->manfid) &&
 633                    (quirks[i].prodid == ~0 ||
 634                     quirks[i].prodid == info->prodid)) {
 635                        info->quirk = &quirks[i];
 636                        break;
 637                }
 638
 639        /*
 640         * Another check for dual-serial cards: look for either serial or
 641         * multifunction cards that ask for appropriate IO port ranges.
 642         */
 643        if ((info->multi == 0) &&
 644            (link->has_func_id) &&
 645            (link->socket->pcmcia_pfc == 0) &&
 646            ((link->func_id == CISTPL_FUNCID_MULTI) ||
 647             (link->func_id == CISTPL_FUNCID_SERIAL))) {
 648                if (pcmcia_loop_config(link, serial_check_for_multi, info))
 649                        goto failed;
 650        }
 651
 652        /*
 653         * Apply any multi-port quirk.
 654         */
 655        if (info->quirk && info->quirk->multi != -1)
 656                info->multi = info->quirk->multi;
 657
 658        dev_info(&link->dev,
 659                "trying to set up [0x%04x:0x%04x] (pfc: %d, multi: %d, quirk: %p)\n",
 660                link->manf_id, link->card_id,
 661                link->socket->pcmcia_pfc, info->multi, info->quirk);
 662        if (link->socket->pcmcia_pfc)
 663                i = pfc_config(link);
 664        else if (info->multi > 1)
 665                i = multi_config(link);
 666        else
 667                i = simple_config(link);
 668
 669        if (i || info->ndev == 0)
 670                goto failed;
 671
 672        /*
 673         * Apply any post-init quirk.  FIXME: This should really happen
 674         * before we register the port, since it might already be in use.
 675         */
 676        if (info->quirk && info->quirk->post)
 677                if (info->quirk->post(link))
 678                        goto failed;
 679
 680        return 0;
 681
 682failed:
 683        dev_warn(&link->dev, "failed to initialize\n");
 684        serial_remove(link);
 685        return -ENODEV;
 686}
 687
 688static const struct pcmcia_device_id serial_ids[] = {
 689        PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0057, 0x0021),
 690        PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0089, 0x110a),
 691        PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0104, 0x000a),
 692        PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0105, 0x0d0a),
 693        PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0105, 0x0e0a),
 694        PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0105, 0xea15),
 695        PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0109, 0x0501),
 696        PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0138, 0x110a),
 697        PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0140, 0x000a),
 698        PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0143, 0x3341),
 699        PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0143, 0xc0ab),
 700        PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x016c, 0x0081),
 701        PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x021b, 0x0101),
 702        PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x08a1, 0xc0ab),
 703        PCMCIA_PFC_DEVICE_PROD_ID123(1, "MEGAHERTZ", "CC/XJEM3288", "DATA/FAX/CELL ETHERNET MODEM", 0xf510db04, 0x04cd2988, 0x46a52d63),
 704        PCMCIA_PFC_DEVICE_PROD_ID123(1, "MEGAHERTZ", "CC/XJEM3336", "DATA/FAX/CELL ETHERNET MODEM", 0xf510db04, 0x0143b773, 0x46a52d63),
 705        PCMCIA_PFC_DEVICE_PROD_ID123(1, "MEGAHERTZ", "EM1144T", "PCMCIA MODEM", 0xf510db04, 0x856d66c8, 0xbd6c43ef),
 706        PCMCIA_PFC_DEVICE_PROD_ID123(1, "MEGAHERTZ", "XJEM1144/CCEM1144", "PCMCIA MODEM", 0xf510db04, 0x52d21e1e, 0xbd6c43ef),
 707        PCMCIA_PFC_DEVICE_PROD_ID13(1, "Xircom", "CEM28", 0x2e3ee845, 0x0ea978ea),
 708        PCMCIA_PFC_DEVICE_PROD_ID13(1, "Xircom", "CEM33", 0x2e3ee845, 0x80609023),
 709        PCMCIA_PFC_DEVICE_PROD_ID13(1, "Xircom", "CEM56", 0x2e3ee845, 0xa650c32a),
 710        PCMCIA_PFC_DEVICE_PROD_ID13(1, "Xircom", "REM10", 0x2e3ee845, 0x76df1d29),
 711        PCMCIA_PFC_DEVICE_PROD_ID13(1, "Xircom", "XEM5600", 0x2e3ee845, 0xf1403719),
 712        PCMCIA_PFC_DEVICE_PROD_ID12(1, "AnyCom", "Fast Ethernet + 56K COMBO", 0x578ba6e7, 0xb0ac62c4),
 713        PCMCIA_PFC_DEVICE_PROD_ID12(1, "ATKK", "LM33-PCM-T", 0xba9eb7e2, 0x077c174e),
 714        PCMCIA_PFC_DEVICE_PROD_ID12(1, "D-Link", "DME336T", 0x1a424a1c, 0xb23897ff),
 715        PCMCIA_PFC_DEVICE_PROD_ID12(1, "Gateway 2000", "XJEM3336", 0xdd9989be, 0x662c394c),
 716        PCMCIA_PFC_DEVICE_PROD_ID12(1, "Grey Cell", "GCS3000", 0x2a151fac, 0x48b932ae),
 717        PCMCIA_PFC_DEVICE_PROD_ID12(1, "Linksys", "EtherFast 10&100 + 56K PC Card (PCMLM56)", 0x0733cc81, 0xb3765033),
 718        PCMCIA_PFC_DEVICE_PROD_ID12(1, "LINKSYS", "PCMLM336", 0xf7cb0b07, 0x7a821b58),
 719        PCMCIA_PFC_DEVICE_PROD_ID12(1, "MEGAHERTZ", "XJEM1144/CCEM1144", 0xf510db04, 0x52d21e1e),
 720        PCMCIA_PFC_DEVICE_PROD_ID12(1, "MICRO RESEARCH", "COMBO-L/M-336", 0xb2ced065, 0x3ced0555),
 721        PCMCIA_PFC_DEVICE_PROD_ID12(1, "NEC", "PK-UG-J001", 0x18df0ba0, 0x831b1064),
 722        PCMCIA_PFC_DEVICE_PROD_ID12(1, "Ositech", "Trumpcard:Jack of Diamonds Modem+Ethernet", 0xc2f80cd, 0x656947b9),
 723        PCMCIA_PFC_DEVICE_PROD_ID12(1, "Ositech", "Trumpcard:Jack of Hearts Modem+Ethernet", 0xc2f80cd, 0xdc9ba5ed),
 724        PCMCIA_PFC_DEVICE_PROD_ID12(1, "PCMCIAs", "ComboCard", 0xdcfe12d3, 0xcd8906cc),
 725        PCMCIA_PFC_DEVICE_PROD_ID12(1, "PCMCIAs", "LanModem", 0xdcfe12d3, 0xc67c648f),
 726        PCMCIA_PFC_DEVICE_PROD_ID12(1, "TDK", "GlobalNetworker 3410/3412", 0x1eae9475, 0xd9a93bed),
 727        PCMCIA_PFC_DEVICE_PROD_ID12(1, "Xircom", "CreditCard Ethernet+Modem II", 0x2e3ee845, 0xeca401bf),
 728        PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0032, 0x0e01),
 729        PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0032, 0x0a05),
 730        PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0032, 0x0b05),
 731        PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0032, 0x1101),
 732        PCMCIA_MFC_DEVICE_MANF_CARD(0, 0x0104, 0x0070),
 733        PCMCIA_MFC_DEVICE_MANF_CARD(1, 0x0101, 0x0562),
 734        PCMCIA_MFC_DEVICE_MANF_CARD(1, 0x0104, 0x0070),
 735        PCMCIA_MFC_DEVICE_MANF_CARD(1, 0x016c, 0x0020),
 736        PCMCIA_MFC_DEVICE_PROD_ID123(1, "APEX DATA", "MULTICARD", "ETHERNET-MODEM", 0x11c2da09, 0x7289dc5d, 0xaad95e1f),
 737        PCMCIA_MFC_DEVICE_PROD_ID12(1, "IBM", "Home and Away 28.8 PC Card       ", 0xb569a6e5, 0x5bd4ff2c),
 738        PCMCIA_MFC_DEVICE_PROD_ID12(1, "IBM", "Home and Away Credit Card Adapter", 0xb569a6e5, 0x4bdf15c3),
 739        PCMCIA_MFC_DEVICE_PROD_ID12(1, "IBM", "w95 Home and Away Credit Card ", 0xb569a6e5, 0xae911c15),
 740        PCMCIA_MFC_DEVICE_PROD_ID1(1, "Motorola MARQUIS", 0xf03e4e77),
 741        PCMCIA_MFC_DEVICE_PROD_ID2(1, "FAX/Modem/Ethernet Combo Card ", 0x1ed59302),
 742        PCMCIA_DEVICE_MANF_CARD(0x0089, 0x0301),
 743        PCMCIA_DEVICE_MANF_CARD(0x00a4, 0x0276),
 744        PCMCIA_DEVICE_MANF_CARD(0x0101, 0x0039),
 745        PCMCIA_DEVICE_MANF_CARD(0x0104, 0x0006),
 746        PCMCIA_DEVICE_MANF_CARD(0x0105, 0x0101), /* TDK DF2814 */
 747        PCMCIA_DEVICE_MANF_CARD(0x0105, 0x100a), /* Xircom CM-56G */
 748        PCMCIA_DEVICE_MANF_CARD(0x0105, 0x3e0a), /* TDK DF5660 */
 749        PCMCIA_DEVICE_MANF_CARD(0x0105, 0x410a),
 750        PCMCIA_DEVICE_MANF_CARD(0x0107, 0x0002), /* USRobotics 14,400 */
 751        PCMCIA_DEVICE_MANF_CARD(0x010b, 0x0d50),
 752        PCMCIA_DEVICE_MANF_CARD(0x010b, 0x0d51),
 753        PCMCIA_DEVICE_MANF_CARD(0x010b, 0x0d52),
 754        PCMCIA_DEVICE_MANF_CARD(0x010b, 0x0d53),
 755        PCMCIA_DEVICE_MANF_CARD(0x010b, 0xd180),
 756        PCMCIA_DEVICE_MANF_CARD(0x0115, 0x3330), /* USRobotics/SUN 14,400 */
 757        PCMCIA_DEVICE_MANF_CARD(0x0124, 0x0100), /* Nokia DTP-2 ver II */
 758        PCMCIA_DEVICE_MANF_CARD(0x0134, 0x5600), /* LASAT COMMUNICATIONS A/S */
 759        PCMCIA_DEVICE_MANF_CARD(0x0137, 0x000e),
 760        PCMCIA_DEVICE_MANF_CARD(0x0137, 0x001b),
 761        PCMCIA_DEVICE_MANF_CARD(0x0137, 0x0025),
 762        PCMCIA_DEVICE_MANF_CARD(0x0137, 0x0045),
 763        PCMCIA_DEVICE_MANF_CARD(0x0137, 0x0052),
 764        PCMCIA_DEVICE_MANF_CARD(0x016c, 0x0006), /* Psion 56K+Fax */
 765        PCMCIA_DEVICE_MANF_CARD(0x0200, 0x0001), /* MultiMobile */
 766        PCMCIA_DEVICE_PROD_ID134("ADV", "TECH", "COMpad-32/85", 0x67459937, 0x916d02ba, 0x8fbe92ae),
 767        PCMCIA_DEVICE_PROD_ID124("GATEWAY2000", "CC3144", "PCMCIA MODEM", 0x506bccae, 0xcb3685f1, 0xbd6c43ef),
 768        PCMCIA_DEVICE_PROD_ID14("MEGAHERTZ", "PCMCIA MODEM", 0xf510db04, 0xbd6c43ef),
 769        PCMCIA_DEVICE_PROD_ID124("TOSHIBA", "T144PF", "PCMCIA MODEM", 0xb4585a1a, 0x7271409c, 0xbd6c43ef),
 770        PCMCIA_DEVICE_PROD_ID123("FUJITSU", "FC14F ", "MBH10213", 0x6ee5a3d8, 0x30ead12b, 0xb00f05a0),
 771        PCMCIA_DEVICE_PROD_ID123("Novatel Wireless", "Merlin UMTS Modem", "U630", 0x32607776, 0xd9e73b13, 0xe87332e),
 772        PCMCIA_DEVICE_PROD_ID13("MEGAHERTZ", "V.34 PCMCIA MODEM", 0xf510db04, 0xbb2cce4a),
 773        PCMCIA_DEVICE_PROD_ID12("Brain Boxes", "Bluetooth PC Card", 0xee138382, 0xd4ce9b02),
 774        PCMCIA_DEVICE_PROD_ID12("CIRRUS LOGIC", "FAX MODEM", 0xe625f451, 0xcecd6dfa),
 775        PCMCIA_DEVICE_PROD_ID12("COMPAQ", "PCMCIA 28800 FAX/DATA MODEM", 0xa3a3062c, 0x8cbd7c76),
 776        PCMCIA_DEVICE_PROD_ID12("COMPAQ", "PCMCIA 33600 FAX/DATA MODEM", 0xa3a3062c, 0x5a00ce95),
 777        PCMCIA_DEVICE_PROD_ID12("Computerboards, Inc.", "PCM-COM422", 0xd0b78f51, 0x7e2d49ed),
 778        PCMCIA_DEVICE_PROD_ID12("Dr. Neuhaus", "FURY CARD 14K4", 0x76942813, 0x8b96ce65),
 779        PCMCIA_DEVICE_PROD_ID12("IBM", "ISDN/56K/GSM", 0xb569a6e5, 0xfee5297b),
 780        PCMCIA_DEVICE_PROD_ID12("Intelligent", "ANGIA FAX/MODEM", 0xb496e65e, 0xf31602a6),
 781        PCMCIA_DEVICE_PROD_ID12("Intel", "MODEM 2400+", 0x816cc815, 0x412729fb),
 782        PCMCIA_DEVICE_PROD_ID12("Intertex", "IX34-PCMCIA", 0xf8a097e3, 0x97880447),
 783        PCMCIA_DEVICE_PROD_ID12("IOTech Inc ", "PCMCIA Dual RS-232 Serial Port Card", 0x3bd2d898, 0x92abc92f),
 784        PCMCIA_DEVICE_PROD_ID12("MACRONIX", "FAX/MODEM", 0x668388b3, 0x3f9bdf2f),
 785        PCMCIA_DEVICE_PROD_ID12("Multi-Tech", "MT1432LT", 0x5f73be51, 0x0b3e2383),
 786        PCMCIA_DEVICE_PROD_ID12("Multi-Tech", "MT2834LT", 0x5f73be51, 0x4cd7c09e),
 787        PCMCIA_DEVICE_PROD_ID12("OEM      ", "C288MX     ", 0xb572d360, 0xd2385b7a),
 788        PCMCIA_DEVICE_PROD_ID12("Option International", "V34bis GSM/PSTN Data/Fax Modem", 0x9d7cd6f5, 0x5cb8bf41),
 789        PCMCIA_DEVICE_PROD_ID12("Option International", "GSM-Ready 56K/ISDN", 0x9d7cd6f5, 0xb23844aa),
 790        PCMCIA_DEVICE_PROD_ID12("PCMCIA   ", "C336MX     ", 0x99bcafe9, 0xaa25bcab),
 791        PCMCIA_DEVICE_PROD_ID12("Quatech Inc", "PCMCIA Dual RS-232 Serial Port Card", 0xc4420b35, 0x92abc92f),
 792        PCMCIA_DEVICE_PROD_ID12("Quatech Inc", "Dual RS-232 Serial Port PC Card", 0xc4420b35, 0x031a380d),
 793        PCMCIA_DEVICE_PROD_ID12("Telia", "SurfinBird 560P/A+", 0xe2cdd5e, 0xc9314b38),
 794        PCMCIA_DEVICE_PROD_ID1("Smart Serial Port", 0x2d8ce292),
 795        PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "PCMCIA", "EN2218-LAN/MODEM", 0x281f1c5d, 0x570f348e, "cis/PCMLM28.cis"),
 796        PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "PCMCIA", "UE2218-LAN/MODEM", 0x281f1c5d, 0x6fdcacee, "cis/PCMLM28.cis"),
 797        PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "Psion Dacom", "Gold Card V34 Ethernet", 0xf5f025c2, 0x338e8155, "cis/PCMLM28.cis"),
 798        PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "Psion Dacom", "Gold Card V34 Ethernet GSM", 0xf5f025c2, 0x4ae85d35, "cis/PCMLM28.cis"),
 799        PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "LINKSYS", "PCMLM28", 0xf7cb0b07, 0x66881874, "cis/PCMLM28.cis"),
 800        PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "TOSHIBA", "Modem/LAN Card", 0xb4585a1a, 0x53f922f8, "cis/PCMLM28.cis"),
 801        PCMCIA_MFC_DEVICE_CIS_PROD_ID12(1, "DAYNA COMMUNICATIONS", "LAN AND MODEM MULTIFUNCTION", 0x8fdf8f89, 0xdd5ed9e8, "cis/DP83903.cis"),
 802        PCMCIA_MFC_DEVICE_CIS_PROD_ID4(1, "NSC MF LAN/Modem", 0x58fc6056, "cis/DP83903.cis"),
 803        PCMCIA_MFC_DEVICE_CIS_MANF_CARD(1, 0x0101, 0x0556, "cis/3CCFEM556.cis"),
 804        PCMCIA_MFC_DEVICE_CIS_MANF_CARD(1, 0x0175, 0x0000, "cis/DP83903.cis"),
 805        PCMCIA_MFC_DEVICE_CIS_MANF_CARD(1, 0x0101, 0x0035, "cis/3CXEM556.cis"),
 806        PCMCIA_MFC_DEVICE_CIS_MANF_CARD(1, 0x0101, 0x003d, "cis/3CXEM556.cis"),
 807        PCMCIA_DEVICE_CIS_PROD_ID12("Sierra Wireless", "AC850", 0xd85f6206, 0x42a2c018, "cis/SW_8xx_SER.cis"), /* Sierra Wireless AC850 3G Network Adapter R1 */
 808        PCMCIA_DEVICE_CIS_PROD_ID12("Sierra Wireless", "AC860", 0xd85f6206, 0x698f93db, "cis/SW_8xx_SER.cis"), /* Sierra Wireless AC860 3G Network Adapter R1 */
 809        PCMCIA_DEVICE_CIS_PROD_ID12("Sierra Wireless", "AC710/AC750", 0xd85f6206, 0x761b11e0, "cis/SW_7xx_SER.cis"),  /* Sierra Wireless AC710/AC750 GPRS Network Adapter R1 */
 810        PCMCIA_DEVICE_CIS_MANF_CARD(0x0192, 0xa555, "cis/SW_555_SER.cis"),  /* Sierra Aircard 555 CDMA 1xrtt Modem -- pre update */
 811        PCMCIA_DEVICE_CIS_MANF_CARD(0x013f, 0xa555, "cis/SW_555_SER.cis"),  /* Sierra Aircard 555 CDMA 1xrtt Modem -- post update */
 812        PCMCIA_DEVICE_CIS_PROD_ID12("MultiTech", "PCMCIA 56K DataFax", 0x842047ee, 0xc2efcf03, "cis/MT5634ZLX.cis"),
 813        PCMCIA_DEVICE_CIS_PROD_ID12("ADVANTECH", "COMpad-32/85B-2", 0x96913a85, 0x27ab5437, "cis/COMpad2.cis"),
 814        PCMCIA_DEVICE_CIS_PROD_ID12("ADVANTECH", "COMpad-32/85B-4", 0x96913a85, 0xcec8f102, "cis/COMpad4.cis"),
 815        PCMCIA_DEVICE_CIS_PROD_ID123("ADVANTECH", "COMpad-32/85", "1.0", 0x96913a85, 0x8fbe92ae, 0x0877b627, "cis/COMpad2.cis"),
 816        PCMCIA_DEVICE_CIS_PROD_ID2("RS-COM 2P", 0xad20b156, "cis/RS-COM-2P.cis"),
 817        PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.", "SERIAL CARD: SL100  1.00.", 0x19ca78af, 0xf964f42b),
 818        PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.", "SERIAL CARD: SL100", 0x19ca78af, 0x71d98e83),
 819        PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.", "SERIAL CARD: SL232  1.00.", 0x19ca78af, 0x69fb7490),
 820        PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.", "SERIAL CARD: SL232", 0x19ca78af, 0xb6bc0235),
 821        PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c2000.", "SERIAL CARD: CF232", 0x63f2e0bd, 0xb9e175d3),
 822        PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c2000.", "SERIAL CARD: CF232-5", 0x63f2e0bd, 0xfce33442),
 823        PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: CF232", 0x3beb8cf2, 0x171e7190),
 824        PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: CF232-5", 0x3beb8cf2, 0x20da4262),
 825        PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: CF428", 0x3beb8cf2, 0xea5dd57d),
 826        PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: CF500", 0x3beb8cf2, 0xd77255fa),
 827        PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: IC232", 0x3beb8cf2, 0x6a709903),
 828        PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: SL232", 0x3beb8cf2, 0x18430676),
 829        PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: XL232", 0x3beb8cf2, 0x6f933767),
 830        PCMCIA_MFC_DEVICE_PROD_ID12(0, "Elan", "Serial Port: CF332", 0x3beb8cf2, 0x16dc1ba7),
 831        PCMCIA_MFC_DEVICE_PROD_ID12(0, "Elan", "Serial Port: SL332", 0x3beb8cf2, 0x19816c41),
 832        PCMCIA_MFC_DEVICE_PROD_ID12(0, "Elan", "Serial Port: SL385", 0x3beb8cf2, 0x64112029),
 833        PCMCIA_MFC_DEVICE_PROD_ID12(0, "Elan", "Serial Port: SL432", 0x3beb8cf2, 0x1cce7ac4),
 834        PCMCIA_MFC_DEVICE_PROD_ID12(0, "Elan", "Serial+Parallel Port: SP230", 0x3beb8cf2, 0xdb9e58bc),
 835        PCMCIA_MFC_DEVICE_PROD_ID12(1, "Elan", "Serial Port: CF332", 0x3beb8cf2, 0x16dc1ba7),
 836        PCMCIA_MFC_DEVICE_PROD_ID12(1, "Elan", "Serial Port: SL332", 0x3beb8cf2, 0x19816c41),
 837        PCMCIA_MFC_DEVICE_PROD_ID12(1, "Elan", "Serial Port: SL385", 0x3beb8cf2, 0x64112029),
 838        PCMCIA_MFC_DEVICE_PROD_ID12(1, "Elan", "Serial Port: SL432", 0x3beb8cf2, 0x1cce7ac4),
 839        PCMCIA_MFC_DEVICE_PROD_ID12(2, "Elan", "Serial Port: SL432", 0x3beb8cf2, 0x1cce7ac4),
 840        PCMCIA_MFC_DEVICE_PROD_ID12(3, "Elan", "Serial Port: SL432", 0x3beb8cf2, 0x1cce7ac4),
 841        PCMCIA_DEVICE_MANF_CARD(0x0279, 0x950b),
 842        /* too generic */
 843        /* PCMCIA_MFC_DEVICE_MANF_CARD(0, 0x0160, 0x0002), */
 844        /* PCMCIA_MFC_DEVICE_MANF_CARD(1, 0x0160, 0x0002), */
 845        PCMCIA_DEVICE_FUNC_ID(2),
 846        PCMCIA_DEVICE_NULL,
 847};
 848MODULE_DEVICE_TABLE(pcmcia, serial_ids);
 849
 850MODULE_FIRMWARE("cis/PCMLM28.cis");
 851MODULE_FIRMWARE("cis/DP83903.cis");
 852MODULE_FIRMWARE("cis/3CCFEM556.cis");
 853MODULE_FIRMWARE("cis/3CXEM556.cis");
 854MODULE_FIRMWARE("cis/SW_8xx_SER.cis");
 855MODULE_FIRMWARE("cis/SW_7xx_SER.cis");
 856MODULE_FIRMWARE("cis/SW_555_SER.cis");
 857MODULE_FIRMWARE("cis/MT5634ZLX.cis");
 858MODULE_FIRMWARE("cis/COMpad2.cis");
 859MODULE_FIRMWARE("cis/COMpad4.cis");
 860MODULE_FIRMWARE("cis/RS-COM-2P.cis");
 861
 862static struct pcmcia_driver serial_cs_driver = {
 863        .owner          = THIS_MODULE,
 864        .name           = "serial_cs",
 865        .probe          = serial_probe,
 866        .remove         = serial_detach,
 867        .id_table       = serial_ids,
 868        .suspend        = serial_suspend,
 869        .resume         = serial_resume,
 870};
 871module_pcmcia_driver(serial_cs_driver);
 872
 873MODULE_LICENSE("GPL");
 874