// SPDX-License-Identifier: GPL-1.0+
/*
 * OHCI HCD (Host Controller Driver) for USB.
 *
 * (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
 * (C) Copyright 2000-2002 David Brownell <dbrownell@users.sourceforge.net>
 * (C) Copyright 2002 Hewlett-Packard Company
 *
 * SA1111 Bus Glue
 *
 * Written by Christopher Hoover <ch@hpl.hp.com>
 * Based on fragments of previous driver by Russell King et al.
 *
 * This file is licenced under the GPL.
 */

#include <asm/mach-types.h>
#include <asm/hardware/sa1111.h>

#ifndef CONFIG_SA1111
#error "This file is SA-1111 bus glue.  CONFIG_SA1111 must be defined."
#endif

#define USB_STATUS      0x0118
#define USB_RESET       0x011c
#define USB_IRQTEST     0x0120

#define USB_RESET_FORCEIFRESET  (1 << 0)
#define USB_RESET_FORCEHCRESET  (1 << 1)
#define USB_RESET_CLKGENRESET   (1 << 2)
#define USB_RESET_SIMSCALEDOWN  (1 << 3)
#define USB_RESET_USBINTTEST    (1 << 4)
#define USB_RESET_SLEEPSTBYEN   (1 << 5)
#define USB_RESET_PWRSENSELOW   (1 << 6)
#define USB_RESET_PWRCTRLLOW    (1 << 7)

#define USB_STATUS_IRQHCIRMTWKUP  (1 <<  7)
#define USB_STATUS_IRQHCIBUFFACC  (1 <<  8)
#define USB_STATUS_NIRQHCIM       (1 <<  9)
#define USB_STATUS_NHCIMFCLR      (1 << 10)
#define USB_STATUS_USBPWRSENSE    (1 << 11)

#if 0
static void dump_hci_status(struct usb_hcd *hcd, const char *label)
{
        unsigned long status = readl_relaxed(hcd->regs + USB_STATUS);

        printk(KERN_DEBUG "%s USB_STATUS = { %s%s%s%s%s}\n", label,
             ((status & USB_STATUS_IRQHCIRMTWKUP) ? "IRQHCIRMTWKUP " : ""),
             ((status & USB_STATUS_IRQHCIBUFFACC) ? "IRQHCIBUFFACC " : ""),
             ((status & USB_STATUS_NIRQHCIM) ? "" : "IRQHCIM "),
             ((status & USB_STATUS_NHCIMFCLR) ? "" : "HCIMFCLR "),
             ((status & USB_STATUS_USBPWRSENSE) ? "USBPWRSENSE " : ""));
}
#endif

static int ohci_sa1111_reset(struct usb_hcd *hcd)
{
        struct ohci_hcd *ohci = hcd_to_ohci(hcd);

        ohci_hcd_init(ohci);
        return ohci_init(ohci);
}

static int ohci_sa1111_start(struct usb_hcd *hcd)
{
        struct ohci_hcd *ohci = hcd_to_ohci(hcd);
        int ret;

        ret = ohci_run(ohci);
        if (ret < 0) {
                ohci_err(ohci, "can't start\n");
                ohci_stop(hcd);
        }
        return ret;
}

static const struct hc_driver ohci_sa1111_hc_driver = {
        .description =          hcd_name,
        .product_desc =         "SA-1111 OHCI",
        .hcd_priv_size =        sizeof(struct ohci_hcd),

        /*
         * generic hardware linkage
         */
        .irq =                  ohci_irq,
        .flags =                HCD_USB11 | HCD_DMA | HCD_MEMORY,

        /*
         * basic lifecycle operations
         */
        .reset =                ohci_sa1111_reset,
        .start =                ohci_sa1111_start,
        .stop =                 ohci_stop,
        .shutdown =             ohci_shutdown,

        /*
         * managing i/o requests and associated device resources
         */
        .urb_enqueue =          ohci_urb_enqueue,
        .urb_dequeue =          ohci_urb_dequeue,
        .endpoint_disable =     ohci_endpoint_disable,

        /*
         * scheduling support
         */
        .get_frame_number =     ohci_get_frame,

        /*
         * root hub support
         */
        .hub_status_data =      ohci_hub_status_data,
        .hub_control =          ohci_hub_control,
#ifdef  CONFIG_PM
        .bus_suspend =          ohci_bus_suspend,
        .bus_resume =           ohci_bus_resume,
#endif
        .start_port_reset =     ohci_start_port_reset,
};

static int sa1111_start_hc(struct sa1111_dev *dev)
{
        unsigned int usb_rst = 0;
        int ret;

        dev_dbg(&dev->dev, "starting SA-1111 OHCI USB Controller\n");

        if (machine_is_xp860() ||
            machine_is_assabet() ||
            machine_is_pfs168() ||
            machine_is_badge4())
                usb_rst = USB_RESET_PWRSENSELOW | USB_RESET_PWRCTRLLOW;

        /*
         * Configure the power sense and control lines.  Place the USB
         * host controller in reset.
         */
        writel_relaxed(usb_rst | USB_RESET_FORCEIFRESET | USB_RESET_FORCEHCRESET,
                      dev->mapbase + USB_RESET);

        /*
         * Now, carefully enable the USB clock, and take
         * the USB host controller out of reset.
         */
        ret = sa1111_enable_device(dev);
        if (ret == 0) {
                udelay(11);
                writel_relaxed(usb_rst, dev->mapbase + USB_RESET);
        }

        return ret;
}

static void sa1111_stop_hc(struct sa1111_dev *dev)
{
        unsigned int usb_rst;

        dev_dbg(&dev->dev, "stopping SA-1111 OHCI USB Controller\n");

        /*
         * Put the USB host controller into reset.
         */
        usb_rst = readl_relaxed(dev->mapbase + USB_RESET);
        writel_relaxed(usb_rst | USB_RESET_FORCEIFRESET | USB_RESET_FORCEHCRESET,
                      dev->mapbase + USB_RESET);

        /*
         * Stop the USB clock.
         */
        sa1111_disable_device(dev);
}

/**
 * ohci_hcd_sa1111_probe - initialize SA-1111-based HCDs
 *
 * Allocates basic resources for this USB host controller, and
 * then invokes the start() method for the HCD associated with it.
 */
static int ohci_hcd_sa1111_probe(struct sa1111_dev *dev)
{
        struct usb_hcd *hcd;
        int ret, irq;

        if (usb_disabled())
                return -ENODEV;

        /*
         * We don't call dma_set_mask_and_coherent() here because the
         * DMA mask has already been appropraitely setup by the core
         * SA-1111 bus code (which includes bug workarounds.)
         */

        hcd = usb_create_hcd(&ohci_sa1111_hc_driver, &dev->dev, "sa1111");
        if (!hcd)
                return -ENOMEM;

        hcd->rsrc_start = dev->res.start;
        hcd->rsrc_len = resource_size(&dev->res);

        irq = sa1111_get_irq(dev, 1);
        if (irq <= 0) {
                ret = irq ? : -ENXIO;
                goto err1;
        }

        if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
                dev_dbg(&dev->dev, "request_mem_region failed\n");
                ret = -EBUSY;
                goto err1;
        }

        hcd->regs = dev->mapbase;

        ret = sa1111_start_hc(dev);
        if (ret)
                goto err2;

        ret = usb_add_hcd(hcd, irq, 0);
        if (ret == 0) {
                device_wakeup_enable(hcd->self.controller);
                return ret;
        }

        sa1111_stop_hc(dev);
 err2:
        release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
 err1:
        usb_put_hcd(hcd);
        return ret;
}

/**
 * ohci_hcd_sa1111_remove - shutdown processing for SA-1111-based HCDs
 * @dev: USB Host Controller being removed
 *
 * Reverses the effect of ohci_hcd_sa1111_probe(), first invoking
 * the HCD's stop() method.
 */
static void ohci_hcd_sa1111_remove(struct sa1111_dev *dev)
{
        struct usb_hcd *hcd = sa1111_get_drvdata(dev);

        usb_remove_hcd(hcd);
        sa1111_stop_hc(dev);
        release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
        usb_put_hcd(hcd);
}

static void ohci_hcd_sa1111_shutdown(struct device *_dev)
{
        struct sa1111_dev *dev = to_sa1111_device(_dev);
        struct usb_hcd *hcd = sa1111_get_drvdata(dev);

        if (test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags)) {
                hcd->driver->shutdown(hcd);
                sa1111_stop_hc(dev);
        }
}

static struct sa1111_driver ohci_hcd_sa1111_driver = {
        .drv = {
                .name   = "sa1111-ohci",
                .owner  = THIS_MODULE,
                .shutdown = ohci_hcd_sa1111_shutdown,
        },
        .devid          = SA1111_DEVID_USB,
        .probe          = ohci_hcd_sa1111_probe,
        .remove         = ohci_hcd_sa1111_remove,
};