linux/drivers/usb/phy/phy-ab8500-usb.c
<<
>>
Prefs
   1// SPDX-License-Identifier: GPL-2.0+
   2/*
   3 * USB transceiver driver for AB8500 family chips
   4 *
   5 * Copyright (C) 2010-2013 ST-Ericsson AB
   6 * Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
   7 * Avinash Kumar <avinash.kumar@stericsson.com>
   8 * Thirupathi Chippakurthy <thirupathi.chippakurthy@stericsson.com>
   9 */
  10
  11#include <linux/module.h>
  12#include <linux/platform_device.h>
  13#include <linux/usb/otg.h>
  14#include <linux/slab.h>
  15#include <linux/notifier.h>
  16#include <linux/interrupt.h>
  17#include <linux/delay.h>
  18#include <linux/clk.h>
  19#include <linux/err.h>
  20#include <linux/mfd/abx500.h>
  21#include <linux/mfd/abx500/ab8500.h>
  22#include <linux/usb/musb-ux500.h>
  23#include <linux/regulator/consumer.h>
  24#include <linux/pinctrl/consumer.h>
  25
  26/* Bank AB8500_SYS_CTRL2_BLOCK */
  27#define AB8500_MAIN_WD_CTRL_REG 0x01
  28
  29/* Bank AB8500_USB */
  30#define AB8500_USB_LINE_STAT_REG 0x80
  31#define AB8505_USB_LINE_STAT_REG 0x94
  32#define AB8500_USB_PHY_CTRL_REG 0x8A
  33
  34/* Bank AB8500_DEVELOPMENT */
  35#define AB8500_BANK12_ACCESS 0x00
  36
  37/* Bank AB8500_DEBUG */
  38#define AB8500_USB_PHY_TUNE1 0x05
  39#define AB8500_USB_PHY_TUNE2 0x06
  40#define AB8500_USB_PHY_TUNE3 0x07
  41
  42/* Bank AB8500_INTERRUPT */
  43#define AB8500_IT_SOURCE2_REG 0x01
  44
  45#define AB8500_BIT_OTG_STAT_ID (1 << 0)
  46#define AB8500_BIT_PHY_CTRL_HOST_EN (1 << 0)
  47#define AB8500_BIT_PHY_CTRL_DEVICE_EN (1 << 1)
  48#define AB8500_BIT_WD_CTRL_ENABLE (1 << 0)
  49#define AB8500_BIT_WD_CTRL_KICK (1 << 1)
  50#define AB8500_BIT_SOURCE2_VBUSDET (1 << 7)
  51
  52#define AB8500_WD_KICK_DELAY_US 100 /* usec */
  53#define AB8500_WD_V11_DISABLE_DELAY_US 100 /* usec */
  54#define AB8500_V20_31952_DISABLE_DELAY_US 100 /* usec */
  55
  56/* Usb line status register */
  57enum ab8500_usb_link_status {
  58        USB_LINK_NOT_CONFIGURED_8500 = 0,
  59        USB_LINK_STD_HOST_NC_8500,
  60        USB_LINK_STD_HOST_C_NS_8500,
  61        USB_LINK_STD_HOST_C_S_8500,
  62        USB_LINK_HOST_CHG_NM_8500,
  63        USB_LINK_HOST_CHG_HS_8500,
  64        USB_LINK_HOST_CHG_HS_CHIRP_8500,
  65        USB_LINK_DEDICATED_CHG_8500,
  66        USB_LINK_ACA_RID_A_8500,
  67        USB_LINK_ACA_RID_B_8500,
  68        USB_LINK_ACA_RID_C_NM_8500,
  69        USB_LINK_ACA_RID_C_HS_8500,
  70        USB_LINK_ACA_RID_C_HS_CHIRP_8500,
  71        USB_LINK_HM_IDGND_8500,
  72        USB_LINK_RESERVED_8500,
  73        USB_LINK_NOT_VALID_LINK_8500,
  74};
  75
  76enum ab8505_usb_link_status {
  77        USB_LINK_NOT_CONFIGURED_8505 = 0,
  78        USB_LINK_STD_HOST_NC_8505,
  79        USB_LINK_STD_HOST_C_NS_8505,
  80        USB_LINK_STD_HOST_C_S_8505,
  81        USB_LINK_CDP_8505,
  82        USB_LINK_RESERVED0_8505,
  83        USB_LINK_RESERVED1_8505,
  84        USB_LINK_DEDICATED_CHG_8505,
  85        USB_LINK_ACA_RID_A_8505,
  86        USB_LINK_ACA_RID_B_8505,
  87        USB_LINK_ACA_RID_C_NM_8505,
  88        USB_LINK_RESERVED2_8505,
  89        USB_LINK_RESERVED3_8505,
  90        USB_LINK_HM_IDGND_8505,
  91        USB_LINK_CHARGERPORT_NOT_OK_8505,
  92        USB_LINK_CHARGER_DM_HIGH_8505,
  93        USB_LINK_PHYEN_NO_VBUS_NO_IDGND_8505,
  94        USB_LINK_STD_UPSTREAM_NO_IDGNG_NO_VBUS_8505,
  95        USB_LINK_STD_UPSTREAM_8505,
  96        USB_LINK_CHARGER_SE1_8505,
  97        USB_LINK_CARKIT_CHGR_1_8505,
  98        USB_LINK_CARKIT_CHGR_2_8505,
  99        USB_LINK_ACA_DOCK_CHGR_8505,
 100        USB_LINK_SAMSUNG_BOOT_CBL_PHY_EN_8505,
 101        USB_LINK_SAMSUNG_BOOT_CBL_PHY_DISB_8505,
 102        USB_LINK_SAMSUNG_UART_CBL_PHY_EN_8505,
 103        USB_LINK_SAMSUNG_UART_CBL_PHY_DISB_8505,
 104        USB_LINK_MOTOROLA_FACTORY_CBL_PHY_EN_8505,
 105};
 106
 107enum ab8500_usb_mode {
 108        USB_IDLE = 0,
 109        USB_PERIPHERAL,
 110        USB_HOST,
 111        USB_DEDICATED_CHG,
 112        USB_UART
 113};
 114
 115/* Register USB_LINK_STATUS interrupt */
 116#define AB8500_USB_FLAG_USE_LINK_STATUS_IRQ     (1 << 0)
 117/* Register ID_WAKEUP_F interrupt */
 118#define AB8500_USB_FLAG_USE_ID_WAKEUP_IRQ       (1 << 1)
 119/* Register VBUS_DET_F interrupt */
 120#define AB8500_USB_FLAG_USE_VBUS_DET_IRQ        (1 << 2)
 121/* Driver is using the ab-iddet driver*/
 122#define AB8500_USB_FLAG_USE_AB_IDDET            (1 << 3)
 123/* Enable setting regulators voltage */
 124#define AB8500_USB_FLAG_REGULATOR_SET_VOLTAGE   (1 << 4)
 125
 126struct ab8500_usb {
 127        struct usb_phy phy;
 128        struct device *dev;
 129        struct ab8500 *ab8500;
 130        unsigned vbus_draw;
 131        struct work_struct phy_dis_work;
 132        enum ab8500_usb_mode mode;
 133        struct clk *sysclk;
 134        struct regulator *v_ape;
 135        struct regulator *v_musb;
 136        struct regulator *v_ulpi;
 137        int saved_v_ulpi;
 138        int previous_link_status_state;
 139        struct pinctrl *pinctrl;
 140        struct pinctrl_state *pins_sleep;
 141        bool enabled_charging_detection;
 142        unsigned int flags;
 143};
 144
 145static inline struct ab8500_usb *phy_to_ab(struct usb_phy *x)
 146{
 147        return container_of(x, struct ab8500_usb, phy);
 148}
 149
 150static void ab8500_usb_wd_workaround(struct ab8500_usb *ab)
 151{
 152        abx500_set_register_interruptible(ab->dev,
 153                AB8500_SYS_CTRL2_BLOCK,
 154                AB8500_MAIN_WD_CTRL_REG,
 155                AB8500_BIT_WD_CTRL_ENABLE);
 156
 157        udelay(AB8500_WD_KICK_DELAY_US);
 158
 159        abx500_set_register_interruptible(ab->dev,
 160                AB8500_SYS_CTRL2_BLOCK,
 161                AB8500_MAIN_WD_CTRL_REG,
 162                (AB8500_BIT_WD_CTRL_ENABLE
 163                | AB8500_BIT_WD_CTRL_KICK));
 164
 165        udelay(AB8500_WD_V11_DISABLE_DELAY_US);
 166
 167        abx500_set_register_interruptible(ab->dev,
 168                AB8500_SYS_CTRL2_BLOCK,
 169                AB8500_MAIN_WD_CTRL_REG,
 170                0);
 171}
 172
 173static void ab8500_usb_regulator_enable(struct ab8500_usb *ab)
 174{
 175        int ret, volt;
 176
 177        ret = regulator_enable(ab->v_ape);
 178        if (ret)
 179                dev_err(ab->dev, "Failed to enable v-ape\n");
 180
 181        if (ab->flags & AB8500_USB_FLAG_REGULATOR_SET_VOLTAGE) {
 182                ab->saved_v_ulpi = regulator_get_voltage(ab->v_ulpi);
 183                if (ab->saved_v_ulpi < 0)
 184                        dev_err(ab->dev, "Failed to get v_ulpi voltage\n");
 185
 186                ret = regulator_set_voltage(ab->v_ulpi, 1300000, 1350000);
 187                if (ret < 0)
 188                        dev_err(ab->dev, "Failed to set the Vintcore to 1.3V, ret=%d\n",
 189                                        ret);
 190
 191                ret = regulator_set_load(ab->v_ulpi, 28000);
 192                if (ret < 0)
 193                        dev_err(ab->dev, "Failed to set optimum mode (ret=%d)\n",
 194                                        ret);
 195        }
 196
 197        ret = regulator_enable(ab->v_ulpi);
 198        if (ret)
 199                dev_err(ab->dev, "Failed to enable vddulpivio18\n");
 200
 201        if (ab->flags & AB8500_USB_FLAG_REGULATOR_SET_VOLTAGE) {
 202                volt = regulator_get_voltage(ab->v_ulpi);
 203                if ((volt != 1300000) && (volt != 1350000))
 204                        dev_err(ab->dev, "Vintcore is not set to 1.3V volt=%d\n",
 205                                        volt);
 206        }
 207
 208        ret = regulator_enable(ab->v_musb);
 209        if (ret)
 210                dev_err(ab->dev, "Failed to enable musb_1v8\n");
 211}
 212
 213static void ab8500_usb_regulator_disable(struct ab8500_usb *ab)
 214{
 215        int ret;
 216
 217        regulator_disable(ab->v_musb);
 218
 219        regulator_disable(ab->v_ulpi);
 220
 221        /* USB is not the only consumer of Vintcore, restore old settings */
 222        if (ab->flags & AB8500_USB_FLAG_REGULATOR_SET_VOLTAGE) {
 223                if (ab->saved_v_ulpi > 0) {
 224                        ret = regulator_set_voltage(ab->v_ulpi,
 225                                        ab->saved_v_ulpi, ab->saved_v_ulpi);
 226                        if (ret < 0)
 227                                dev_err(ab->dev, "Failed to set the Vintcore to %duV, ret=%d\n",
 228                                                ab->saved_v_ulpi, ret);
 229                }
 230
 231                ret = regulator_set_load(ab->v_ulpi, 0);
 232                if (ret < 0)
 233                        dev_err(ab->dev, "Failed to set optimum mode (ret=%d)\n",
 234                                        ret);
 235        }
 236
 237        regulator_disable(ab->v_ape);
 238}
 239
 240static void ab8500_usb_wd_linkstatus(struct ab8500_usb *ab, u8 bit)
 241{
 242        /* Workaround for v2.0 bug # 31952 */
 243        if (is_ab8500_2p0(ab->ab8500)) {
 244                abx500_mask_and_set_register_interruptible(ab->dev,
 245                                AB8500_USB, AB8500_USB_PHY_CTRL_REG,
 246                                bit, bit);
 247                udelay(AB8500_V20_31952_DISABLE_DELAY_US);
 248        }
 249}
 250
 251static void ab8500_usb_phy_enable(struct ab8500_usb *ab, bool sel_host)
 252{
 253        u8 bit;
 254        bit = sel_host ? AB8500_BIT_PHY_CTRL_HOST_EN :
 255                AB8500_BIT_PHY_CTRL_DEVICE_EN;
 256
 257        /* mux and configure USB pins to DEFAULT state */
 258        ab->pinctrl = pinctrl_get_select(ab->dev, PINCTRL_STATE_DEFAULT);
 259        if (IS_ERR(ab->pinctrl))
 260                dev_err(ab->dev, "could not get/set default pinstate\n");
 261
 262        if (clk_prepare_enable(ab->sysclk))
 263                dev_err(ab->dev, "can't prepare/enable clock\n");
 264
 265        ab8500_usb_regulator_enable(ab);
 266
 267        abx500_mask_and_set_register_interruptible(ab->dev,
 268                        AB8500_USB, AB8500_USB_PHY_CTRL_REG,
 269                        bit, bit);
 270}
 271
 272static void ab8500_usb_phy_disable(struct ab8500_usb *ab, bool sel_host)
 273{
 274        u8 bit;
 275        bit = sel_host ? AB8500_BIT_PHY_CTRL_HOST_EN :
 276                AB8500_BIT_PHY_CTRL_DEVICE_EN;
 277
 278        ab8500_usb_wd_linkstatus(ab, bit);
 279
 280        abx500_mask_and_set_register_interruptible(ab->dev,
 281                        AB8500_USB, AB8500_USB_PHY_CTRL_REG,
 282                        bit, 0);
 283
 284        /* Needed to disable the phy.*/
 285        ab8500_usb_wd_workaround(ab);
 286
 287        clk_disable_unprepare(ab->sysclk);
 288
 289        ab8500_usb_regulator_disable(ab);
 290
 291        if (!IS_ERR(ab->pinctrl)) {
 292                /* configure USB pins to SLEEP state */
 293                ab->pins_sleep = pinctrl_lookup_state(ab->pinctrl,
 294                                PINCTRL_STATE_SLEEP);
 295
 296                if (IS_ERR(ab->pins_sleep))
 297                        dev_dbg(ab->dev, "could not get sleep pinstate\n");
 298                else if (pinctrl_select_state(ab->pinctrl, ab->pins_sleep))
 299                        dev_err(ab->dev, "could not set pins to sleep state\n");
 300
 301                /*
 302                 * as USB pins are shared with iddet, release them to allow
 303                 * iddet to request them
 304                 */
 305                pinctrl_put(ab->pinctrl);
 306        }
 307}
 308
 309#define ab8500_usb_host_phy_en(ab)      ab8500_usb_phy_enable(ab, true)
 310#define ab8500_usb_host_phy_dis(ab)     ab8500_usb_phy_disable(ab, true)
 311#define ab8500_usb_peri_phy_en(ab)      ab8500_usb_phy_enable(ab, false)
 312#define ab8500_usb_peri_phy_dis(ab)     ab8500_usb_phy_disable(ab, false)
 313
 314static int ab8505_usb_link_status_update(struct ab8500_usb *ab,
 315                enum ab8505_usb_link_status lsts)
 316{
 317        enum ux500_musb_vbus_id_status event = 0;
 318
 319        dev_dbg(ab->dev, "ab8505_usb_link_status_update %d\n", lsts);
 320
 321        /*
 322         * Spurious link_status interrupts are seen at the time of
 323         * disconnection of a device in RIDA state
 324         */
 325        if (ab->previous_link_status_state == USB_LINK_ACA_RID_A_8505 &&
 326                        (lsts == USB_LINK_STD_HOST_NC_8505))
 327                return 0;
 328
 329        ab->previous_link_status_state = lsts;
 330
 331        switch (lsts) {
 332        case USB_LINK_ACA_RID_B_8505:
 333                event = UX500_MUSB_RIDB;
 334                fallthrough;
 335        case USB_LINK_NOT_CONFIGURED_8505:
 336        case USB_LINK_RESERVED0_8505:
 337        case USB_LINK_RESERVED1_8505:
 338        case USB_LINK_RESERVED2_8505:
 339        case USB_LINK_RESERVED3_8505:
 340                ab->mode = USB_IDLE;
 341                ab->phy.otg->default_a = false;
 342                ab->vbus_draw = 0;
 343                if (event != UX500_MUSB_RIDB)
 344                        event = UX500_MUSB_NONE;
 345                /*
 346                 * Fallback to default B_IDLE as nothing
 347                 * is connected
 348                 */
 349                ab->phy.otg->state = OTG_STATE_B_IDLE;
 350                usb_phy_set_event(&ab->phy, USB_EVENT_NONE);
 351                break;
 352
 353        case USB_LINK_ACA_RID_C_NM_8505:
 354                event = UX500_MUSB_RIDC;
 355                fallthrough;
 356        case USB_LINK_STD_HOST_NC_8505:
 357        case USB_LINK_STD_HOST_C_NS_8505:
 358        case USB_LINK_STD_HOST_C_S_8505:
 359        case USB_LINK_CDP_8505:
 360                if (ab->mode == USB_IDLE) {
 361                        ab->mode = USB_PERIPHERAL;
 362                        ab8500_usb_peri_phy_en(ab);
 363                        atomic_notifier_call_chain(&ab->phy.notifier,
 364                                        UX500_MUSB_PREPARE, &ab->vbus_draw);
 365                        usb_phy_set_event(&ab->phy, USB_EVENT_ENUMERATED);
 366                }
 367                if (event != UX500_MUSB_RIDC)
 368                        event = UX500_MUSB_VBUS;
 369                break;
 370
 371        case USB_LINK_ACA_RID_A_8505:
 372        case USB_LINK_ACA_DOCK_CHGR_8505:
 373                event = UX500_MUSB_RIDA;
 374                fallthrough;
 375        case USB_LINK_HM_IDGND_8505:
 376                if (ab->mode == USB_IDLE) {
 377                        ab->mode = USB_HOST;
 378                        ab8500_usb_host_phy_en(ab);
 379                        atomic_notifier_call_chain(&ab->phy.notifier,
 380                                        UX500_MUSB_PREPARE, &ab->vbus_draw);
 381                }
 382                ab->phy.otg->default_a = true;
 383                if (event != UX500_MUSB_RIDA)
 384                        event = UX500_MUSB_ID;
 385                atomic_notifier_call_chain(&ab->phy.notifier,
 386                                event, &ab->vbus_draw);
 387                break;
 388
 389        case USB_LINK_DEDICATED_CHG_8505:
 390                ab->mode = USB_DEDICATED_CHG;
 391                event = UX500_MUSB_CHARGER;
 392                atomic_notifier_call_chain(&ab->phy.notifier,
 393                                event, &ab->vbus_draw);
 394                usb_phy_set_event(&ab->phy, USB_EVENT_CHARGER);
 395                break;
 396
 397        /*
 398         * FIXME: For now we rely on the boot firmware to set up the necessary
 399         * PHY/pin configuration for UART mode.
 400         *
 401         * AB8505 does not seem to report any status change for UART cables,
 402         * possibly because it cannot detect them autonomously.
 403         * We may need to measure the ID resistance manually to reliably
 404         * detect UART cables after bootup.
 405         */
 406        case USB_LINK_SAMSUNG_UART_CBL_PHY_EN_8505:
 407        case USB_LINK_SAMSUNG_UART_CBL_PHY_DISB_8505:
 408                if (ab->mode == USB_IDLE) {
 409                        ab->mode = USB_UART;
 410                        ab8500_usb_peri_phy_en(ab);
 411                }
 412
 413                break;
 414
 415        default:
 416                break;
 417        }
 418
 419        return 0;
 420}
 421
 422static int ab8500_usb_link_status_update(struct ab8500_usb *ab,
 423                enum ab8500_usb_link_status lsts)
 424{
 425        enum ux500_musb_vbus_id_status event = 0;
 426
 427        dev_dbg(ab->dev, "ab8500_usb_link_status_update %d\n", lsts);
 428
 429        /*
 430         * Spurious link_status interrupts are seen in case of a
 431         * disconnection of a device in IDGND and RIDA stage
 432         */
 433        if (ab->previous_link_status_state == USB_LINK_HM_IDGND_8500 &&
 434                        (lsts == USB_LINK_STD_HOST_C_NS_8500 ||
 435                         lsts == USB_LINK_STD_HOST_NC_8500))
 436                return 0;
 437
 438        if (ab->previous_link_status_state == USB_LINK_ACA_RID_A_8500 &&
 439                        lsts == USB_LINK_STD_HOST_NC_8500)
 440                return 0;
 441
 442        ab->previous_link_status_state = lsts;
 443
 444        switch (lsts) {
 445        case USB_LINK_ACA_RID_B_8500:
 446                event = UX500_MUSB_RIDB;
 447                fallthrough;
 448        case USB_LINK_NOT_CONFIGURED_8500:
 449        case USB_LINK_NOT_VALID_LINK_8500:
 450                ab->mode = USB_IDLE;
 451                ab->phy.otg->default_a = false;
 452                ab->vbus_draw = 0;
 453                if (event != UX500_MUSB_RIDB)
 454                        event = UX500_MUSB_NONE;
 455                /* Fallback to default B_IDLE as nothing is connected */
 456                ab->phy.otg->state = OTG_STATE_B_IDLE;
 457                usb_phy_set_event(&ab->phy, USB_EVENT_NONE);
 458                break;
 459
 460        case USB_LINK_ACA_RID_C_NM_8500:
 461        case USB_LINK_ACA_RID_C_HS_8500:
 462        case USB_LINK_ACA_RID_C_HS_CHIRP_8500:
 463                event = UX500_MUSB_RIDC;
 464                fallthrough;
 465        case USB_LINK_STD_HOST_NC_8500:
 466        case USB_LINK_STD_HOST_C_NS_8500:
 467        case USB_LINK_STD_HOST_C_S_8500:
 468        case USB_LINK_HOST_CHG_NM_8500:
 469        case USB_LINK_HOST_CHG_HS_8500:
 470        case USB_LINK_HOST_CHG_HS_CHIRP_8500:
 471                if (ab->mode == USB_IDLE) {
 472                        ab->mode = USB_PERIPHERAL;
 473                        ab8500_usb_peri_phy_en(ab);
 474                        atomic_notifier_call_chain(&ab->phy.notifier,
 475                                        UX500_MUSB_PREPARE, &ab->vbus_draw);
 476                        usb_phy_set_event(&ab->phy, USB_EVENT_ENUMERATED);
 477                }
 478                if (event != UX500_MUSB_RIDC)
 479                        event = UX500_MUSB_VBUS;
 480                break;
 481
 482        case USB_LINK_ACA_RID_A_8500:
 483                event = UX500_MUSB_RIDA;
 484                fallthrough;
 485        case USB_LINK_HM_IDGND_8500:
 486                if (ab->mode == USB_IDLE) {
 487                        ab->mode = USB_HOST;
 488                        ab8500_usb_host_phy_en(ab);
 489                        atomic_notifier_call_chain(&ab->phy.notifier,
 490                                        UX500_MUSB_PREPARE, &ab->vbus_draw);
 491                }
 492                ab->phy.otg->default_a = true;
 493                if (event != UX500_MUSB_RIDA)
 494                        event = UX500_MUSB_ID;
 495                atomic_notifier_call_chain(&ab->phy.notifier,
 496                                event, &ab->vbus_draw);
 497                break;
 498
 499        case USB_LINK_DEDICATED_CHG_8500:
 500                ab->mode = USB_DEDICATED_CHG;
 501                event = UX500_MUSB_CHARGER;
 502                atomic_notifier_call_chain(&ab->phy.notifier,
 503                                event, &ab->vbus_draw);
 504                usb_phy_set_event(&ab->phy, USB_EVENT_CHARGER);
 505                break;
 506
 507        case USB_LINK_RESERVED_8500:
 508                break;
 509        }
 510
 511        return 0;
 512}
 513
 514/*
 515 * Connection Sequence:
 516 *   1. Link Status Interrupt
 517 *   2. Enable AB clock
 518 *   3. Enable AB regulators
 519 *   4. Enable USB phy
 520 *   5. Reset the musb controller
 521 *   6. Switch the ULPI GPIO pins to function mode
 522 *   7. Enable the musb Peripheral5 clock
 523 *   8. Restore MUSB context
 524 */
 525static int abx500_usb_link_status_update(struct ab8500_usb *ab)
 526{
 527        u8 reg;
 528        int ret = 0;
 529
 530        if (is_ab8500(ab->ab8500)) {
 531                enum ab8500_usb_link_status lsts;
 532
 533                ret = abx500_get_register_interruptible(ab->dev,
 534                                AB8500_USB, AB8500_USB_LINE_STAT_REG, &reg);
 535                if (ret < 0)
 536                        return ret;
 537                lsts = (reg >> 3) & 0x0F;
 538                ret = ab8500_usb_link_status_update(ab, lsts);
 539        } else if (is_ab8505(ab->ab8500)) {
 540                enum ab8505_usb_link_status lsts;
 541
 542                ret = abx500_get_register_interruptible(ab->dev,
 543                                AB8500_USB, AB8505_USB_LINE_STAT_REG, &reg);
 544                if (ret < 0)
 545                        return ret;
 546                lsts = (reg >> 3) & 0x1F;
 547                ret = ab8505_usb_link_status_update(ab, lsts);
 548        }
 549
 550        return ret;
 551}
 552
 553/*
 554 * Disconnection Sequence:
 555 *   1. Disconnect Interrupt
 556 *   2. Disable regulators
 557 *   3. Disable AB clock
 558 *   4. Disable the Phy
 559 *   5. Link Status Interrupt
 560 *   6. Disable Musb Clock
 561 */
 562static irqreturn_t ab8500_usb_disconnect_irq(int irq, void *data)
 563{
 564        struct ab8500_usb *ab = (struct ab8500_usb *) data;
 565        enum usb_phy_events event = USB_EVENT_NONE;
 566
 567        /* Link status will not be updated till phy is disabled. */
 568        if (ab->mode == USB_HOST) {
 569                ab->phy.otg->default_a = false;
 570                ab->vbus_draw = 0;
 571                atomic_notifier_call_chain(&ab->phy.notifier,
 572                                event, &ab->vbus_draw);
 573                ab8500_usb_host_phy_dis(ab);
 574                ab->mode = USB_IDLE;
 575        }
 576
 577        if (ab->mode == USB_PERIPHERAL) {
 578                atomic_notifier_call_chain(&ab->phy.notifier,
 579                                event, &ab->vbus_draw);
 580                ab8500_usb_peri_phy_dis(ab);
 581                atomic_notifier_call_chain(&ab->phy.notifier,
 582                                UX500_MUSB_CLEAN, &ab->vbus_draw);
 583                ab->mode = USB_IDLE;
 584                ab->phy.otg->default_a = false;
 585                ab->vbus_draw = 0;
 586        }
 587
 588        if (ab->mode == USB_UART) {
 589                ab8500_usb_peri_phy_dis(ab);
 590                ab->mode = USB_IDLE;
 591        }
 592
 593        if (is_ab8500_2p0(ab->ab8500)) {
 594                if (ab->mode == USB_DEDICATED_CHG) {
 595                        ab8500_usb_wd_linkstatus(ab,
 596                                        AB8500_BIT_PHY_CTRL_DEVICE_EN);
 597                        abx500_mask_and_set_register_interruptible(ab->dev,
 598                                        AB8500_USB, AB8500_USB_PHY_CTRL_REG,
 599                                        AB8500_BIT_PHY_CTRL_DEVICE_EN, 0);
 600                }
 601        }
 602
 603        return IRQ_HANDLED;
 604}
 605
 606static irqreturn_t ab8500_usb_link_status_irq(int irq, void *data)
 607{
 608        struct ab8500_usb *ab = (struct ab8500_usb *)data;
 609
 610        abx500_usb_link_status_update(ab);
 611
 612        return IRQ_HANDLED;
 613}
 614
 615static void ab8500_usb_phy_disable_work(struct work_struct *work)
 616{
 617        struct ab8500_usb *ab = container_of(work, struct ab8500_usb,
 618                                                phy_dis_work);
 619
 620        if (!ab->phy.otg->host)
 621                ab8500_usb_host_phy_dis(ab);
 622
 623        if (!ab->phy.otg->gadget)
 624                ab8500_usb_peri_phy_dis(ab);
 625}
 626
 627static int ab8500_usb_set_suspend(struct usb_phy *x, int suspend)
 628{
 629        /* TODO */
 630        return 0;
 631}
 632
 633static int ab8500_usb_set_peripheral(struct usb_otg *otg,
 634                                        struct usb_gadget *gadget)
 635{
 636        struct ab8500_usb *ab;
 637
 638        if (!otg)
 639                return -ENODEV;
 640
 641        ab = phy_to_ab(otg->usb_phy);
 642
 643        ab->phy.otg->gadget = gadget;
 644
 645        /* Some drivers call this function in atomic context.
 646         * Do not update ab8500 registers directly till this
 647         * is fixed.
 648         */
 649
 650        if ((ab->mode != USB_IDLE) && !gadget) {
 651                ab->mode = USB_IDLE;
 652                schedule_work(&ab->phy_dis_work);
 653        }
 654
 655        return 0;
 656}
 657
 658static int ab8500_usb_set_host(struct usb_otg *otg, struct usb_bus *host)
 659{
 660        struct ab8500_usb *ab;
 661
 662        if (!otg)
 663                return -ENODEV;
 664
 665        ab = phy_to_ab(otg->usb_phy);
 666
 667        ab->phy.otg->host = host;
 668
 669        /* Some drivers call this function in atomic context.
 670         * Do not update ab8500 registers directly till this
 671         * is fixed.
 672         */
 673
 674        if ((ab->mode != USB_IDLE) && !host) {
 675                ab->mode = USB_IDLE;
 676                schedule_work(&ab->phy_dis_work);
 677        }
 678
 679        return 0;
 680}
 681
 682static void ab8500_usb_restart_phy(struct ab8500_usb *ab)
 683{
 684        abx500_mask_and_set_register_interruptible(ab->dev,
 685                        AB8500_USB, AB8500_USB_PHY_CTRL_REG,
 686                        AB8500_BIT_PHY_CTRL_DEVICE_EN,
 687                        AB8500_BIT_PHY_CTRL_DEVICE_EN);
 688
 689        udelay(100);
 690
 691        abx500_mask_and_set_register_interruptible(ab->dev,
 692                        AB8500_USB, AB8500_USB_PHY_CTRL_REG,
 693                        AB8500_BIT_PHY_CTRL_DEVICE_EN,
 694                        0);
 695
 696        abx500_mask_and_set_register_interruptible(ab->dev,
 697                        AB8500_USB, AB8500_USB_PHY_CTRL_REG,
 698                        AB8500_BIT_PHY_CTRL_HOST_EN,
 699                        AB8500_BIT_PHY_CTRL_HOST_EN);
 700
 701        udelay(100);
 702
 703        abx500_mask_and_set_register_interruptible(ab->dev,
 704                        AB8500_USB, AB8500_USB_PHY_CTRL_REG,
 705                        AB8500_BIT_PHY_CTRL_HOST_EN,
 706                        0);
 707}
 708
 709static int ab8500_usb_regulator_get(struct ab8500_usb *ab)
 710{
 711        int err;
 712
 713        ab->v_ape = devm_regulator_get(ab->dev, "v-ape");
 714        if (IS_ERR(ab->v_ape)) {
 715                dev_err(ab->dev, "Could not get v-ape supply\n");
 716                err = PTR_ERR(ab->v_ape);
 717                return err;
 718        }
 719
 720        ab->v_ulpi = devm_regulator_get(ab->dev, "vddulpivio18");
 721        if (IS_ERR(ab->v_ulpi)) {
 722                dev_err(ab->dev, "Could not get vddulpivio18 supply\n");
 723                err = PTR_ERR(ab->v_ulpi);
 724                return err;
 725        }
 726
 727        ab->v_musb = devm_regulator_get(ab->dev, "musb_1v8");
 728        if (IS_ERR(ab->v_musb)) {
 729                dev_err(ab->dev, "Could not get musb_1v8 supply\n");
 730                err = PTR_ERR(ab->v_musb);
 731                return err;
 732        }
 733
 734        return 0;
 735}
 736
 737static int ab8500_usb_irq_setup(struct platform_device *pdev,
 738                struct ab8500_usb *ab)
 739{
 740        int err;
 741        int irq;
 742
 743        if (ab->flags & AB8500_USB_FLAG_USE_LINK_STATUS_IRQ) {
 744                irq = platform_get_irq_byname(pdev, "USB_LINK_STATUS");
 745                if (irq < 0)
 746                        return irq;
 747                err = devm_request_threaded_irq(&pdev->dev, irq, NULL,
 748                                ab8500_usb_link_status_irq,
 749                                IRQF_NO_SUSPEND | IRQF_SHARED | IRQF_ONESHOT,
 750                                "usb-link-status", ab);
 751                if (err < 0) {
 752                        dev_err(ab->dev, "request_irq failed for link status irq\n");
 753                        return err;
 754                }
 755        }
 756
 757        if (ab->flags & AB8500_USB_FLAG_USE_ID_WAKEUP_IRQ) {
 758                irq = platform_get_irq_byname(pdev, "ID_WAKEUP_F");
 759                if (irq < 0)
 760                        return irq;
 761                err = devm_request_threaded_irq(&pdev->dev, irq, NULL,
 762                                ab8500_usb_disconnect_irq,
 763                                IRQF_NO_SUSPEND | IRQF_SHARED | IRQF_ONESHOT,
 764                                "usb-id-fall", ab);
 765                if (err < 0) {
 766                        dev_err(ab->dev, "request_irq failed for ID fall irq\n");
 767                        return err;
 768                }
 769        }
 770
 771        if (ab->flags & AB8500_USB_FLAG_USE_VBUS_DET_IRQ) {
 772                irq = platform_get_irq_byname(pdev, "VBUS_DET_F");
 773                if (irq < 0)
 774                        return irq;
 775                err = devm_request_threaded_irq(&pdev->dev, irq, NULL,
 776                                ab8500_usb_disconnect_irq,
 777                                IRQF_NO_SUSPEND | IRQF_SHARED | IRQF_ONESHOT,
 778                                "usb-vbus-fall", ab);
 779                if (err < 0) {
 780                        dev_err(ab->dev, "request_irq failed for Vbus fall irq\n");
 781                        return err;
 782                }
 783        }
 784
 785        return 0;
 786}
 787
 788static void ab8500_usb_set_ab8500_tuning_values(struct ab8500_usb *ab)
 789{
 790        int err;
 791
 792        /* Enable the PBT/Bank 0x12 access */
 793        err = abx500_set_register_interruptible(ab->dev,
 794                        AB8500_DEVELOPMENT, AB8500_BANK12_ACCESS, 0x01);
 795        if (err < 0)
 796                dev_err(ab->dev, "Failed to enable bank12 access err=%d\n",
 797                                err);
 798
 799        err = abx500_set_register_interruptible(ab->dev,
 800                        AB8500_DEBUG, AB8500_USB_PHY_TUNE1, 0xC8);
 801        if (err < 0)
 802                dev_err(ab->dev, "Failed to set PHY_TUNE1 register err=%d\n",
 803                                err);
 804
 805        err = abx500_set_register_interruptible(ab->dev,
 806                        AB8500_DEBUG, AB8500_USB_PHY_TUNE2, 0x00);
 807        if (err < 0)
 808                dev_err(ab->dev, "Failed to set PHY_TUNE2 register err=%d\n",
 809                                err);
 810
 811        err = abx500_set_register_interruptible(ab->dev,
 812                        AB8500_DEBUG, AB8500_USB_PHY_TUNE3, 0x78);
 813        if (err < 0)
 814                dev_err(ab->dev, "Failed to set PHY_TUNE3 register err=%d\n",
 815                                err);
 816
 817        /* Switch to normal mode/disable Bank 0x12 access */
 818        err = abx500_set_register_interruptible(ab->dev,
 819                        AB8500_DEVELOPMENT, AB8500_BANK12_ACCESS, 0x00);
 820        if (err < 0)
 821                dev_err(ab->dev, "Failed to switch bank12 access err=%d\n",
 822                                err);
 823}
 824
 825static void ab8500_usb_set_ab8505_tuning_values(struct ab8500_usb *ab)
 826{
 827        int err;
 828
 829        /* Enable the PBT/Bank 0x12 access */
 830        err = abx500_mask_and_set_register_interruptible(ab->dev,
 831                        AB8500_DEVELOPMENT, AB8500_BANK12_ACCESS,
 832                        0x01, 0x01);
 833        if (err < 0)
 834                dev_err(ab->dev, "Failed to enable bank12 access err=%d\n",
 835                                err);
 836
 837        err = abx500_mask_and_set_register_interruptible(ab->dev,
 838                        AB8500_DEBUG, AB8500_USB_PHY_TUNE1,
 839                        0xC8, 0xC8);
 840        if (err < 0)
 841                dev_err(ab->dev, "Failed to set PHY_TUNE1 register err=%d\n",
 842                                err);
 843
 844        err = abx500_mask_and_set_register_interruptible(ab->dev,
 845                        AB8500_DEBUG, AB8500_USB_PHY_TUNE2,
 846                        0x60, 0x60);
 847        if (err < 0)
 848                dev_err(ab->dev, "Failed to set PHY_TUNE2 register err=%d\n",
 849                                err);
 850
 851        err = abx500_mask_and_set_register_interruptible(ab->dev,
 852                        AB8500_DEBUG, AB8500_USB_PHY_TUNE3,
 853                        0xFC, 0x80);
 854
 855        if (err < 0)
 856                dev_err(ab->dev, "Failed to set PHY_TUNE3 register err=%d\n",
 857                                err);
 858
 859        /* Switch to normal mode/disable Bank 0x12 access */
 860        err = abx500_mask_and_set_register_interruptible(ab->dev,
 861                        AB8500_DEVELOPMENT, AB8500_BANK12_ACCESS,
 862                        0x00, 0x00);
 863        if (err < 0)
 864                dev_err(ab->dev, "Failed to switch bank12 access err=%d\n",
 865                                err);
 866}
 867
 868static int ab8500_usb_probe(struct platform_device *pdev)
 869{
 870        struct ab8500_usb       *ab;
 871        struct ab8500           *ab8500;
 872        struct usb_otg          *otg;
 873        int err;
 874        int rev;
 875
 876        ab8500 = dev_get_drvdata(pdev->dev.parent);
 877        rev = abx500_get_chip_id(&pdev->dev);
 878
 879        if (is_ab8500_1p1_or_earlier(ab8500)) {
 880                dev_err(&pdev->dev, "Unsupported AB8500 chip rev=%d\n", rev);
 881                return -ENODEV;
 882        }
 883
 884        ab = devm_kzalloc(&pdev->dev, sizeof(*ab), GFP_KERNEL);
 885        if (!ab)
 886                return -ENOMEM;
 887
 888        otg = devm_kzalloc(&pdev->dev, sizeof(*otg), GFP_KERNEL);
 889        if (!otg)
 890                return -ENOMEM;
 891
 892        ab->dev                 = &pdev->dev;
 893        ab->ab8500              = ab8500;
 894        ab->phy.dev             = ab->dev;
 895        ab->phy.otg             = otg;
 896        ab->phy.label           = "ab8500";
 897        ab->phy.set_suspend     = ab8500_usb_set_suspend;
 898        ab->phy.otg->state      = OTG_STATE_UNDEFINED;
 899
 900        otg->usb_phy            = &ab->phy;
 901        otg->set_host           = ab8500_usb_set_host;
 902        otg->set_peripheral     = ab8500_usb_set_peripheral;
 903
 904        if (is_ab8500(ab->ab8500)) {
 905                ab->flags |= AB8500_USB_FLAG_USE_LINK_STATUS_IRQ |
 906                        AB8500_USB_FLAG_USE_ID_WAKEUP_IRQ |
 907                        AB8500_USB_FLAG_USE_VBUS_DET_IRQ |
 908                        AB8500_USB_FLAG_REGULATOR_SET_VOLTAGE;
 909        } else if (is_ab8505(ab->ab8500)) {
 910                ab->flags |= AB8500_USB_FLAG_USE_LINK_STATUS_IRQ |
 911                        AB8500_USB_FLAG_USE_ID_WAKEUP_IRQ |
 912                        AB8500_USB_FLAG_USE_VBUS_DET_IRQ |
 913                        AB8500_USB_FLAG_REGULATOR_SET_VOLTAGE;
 914        }
 915
 916        /* Disable regulator voltage setting for AB8500 <= v2.0 */
 917        if (is_ab8500_2p0_or_earlier(ab->ab8500))
 918                ab->flags &= ~AB8500_USB_FLAG_REGULATOR_SET_VOLTAGE;
 919
 920        platform_set_drvdata(pdev, ab);
 921
 922        /* all: Disable phy when called from set_host and set_peripheral */
 923        INIT_WORK(&ab->phy_dis_work, ab8500_usb_phy_disable_work);
 924
 925        err = ab8500_usb_regulator_get(ab);
 926        if (err)
 927                return err;
 928
 929        ab->sysclk = devm_clk_get(ab->dev, "sysclk");
 930        if (IS_ERR(ab->sysclk)) {
 931                dev_err(ab->dev, "Could not get sysclk.\n");
 932                return PTR_ERR(ab->sysclk);
 933        }
 934
 935        err = ab8500_usb_irq_setup(pdev, ab);
 936        if (err < 0)
 937                return err;
 938
 939        err = usb_add_phy(&ab->phy, USB_PHY_TYPE_USB2);
 940        if (err) {
 941                dev_err(&pdev->dev, "Can't register transceiver\n");
 942                return err;
 943        }
 944
 945        if (is_ab8500(ab->ab8500) && !is_ab8500_2p0_or_earlier(ab->ab8500))
 946                /* Phy tuning values for AB8500 > v2.0 */
 947                ab8500_usb_set_ab8500_tuning_values(ab);
 948        else if (is_ab8505(ab->ab8500))
 949                /* Phy tuning values for AB8505 */
 950                ab8500_usb_set_ab8505_tuning_values(ab);
 951
 952        /* Needed to enable ID detection. */
 953        ab8500_usb_wd_workaround(ab);
 954
 955        /*
 956         * This is required for usb-link-status to work properly when a
 957         * cable is connected at boot time.
 958         */
 959        ab8500_usb_restart_phy(ab);
 960
 961        abx500_usb_link_status_update(ab);
 962
 963        dev_info(&pdev->dev, "revision 0x%2x driver initialized\n", rev);
 964
 965        return 0;
 966}
 967
 968static int ab8500_usb_remove(struct platform_device *pdev)
 969{
 970        struct ab8500_usb *ab = platform_get_drvdata(pdev);
 971
 972        cancel_work_sync(&ab->phy_dis_work);
 973
 974        usb_remove_phy(&ab->phy);
 975
 976        if (ab->mode == USB_HOST)
 977                ab8500_usb_host_phy_dis(ab);
 978        else if (ab->mode == USB_PERIPHERAL)
 979                ab8500_usb_peri_phy_dis(ab);
 980
 981        return 0;
 982}
 983
 984static const struct platform_device_id ab8500_usb_devtype[] = {
 985        { .name = "ab8500-usb", },
 986        { /* sentinel */ }
 987};
 988MODULE_DEVICE_TABLE(platform, ab8500_usb_devtype);
 989
 990static struct platform_driver ab8500_usb_driver = {
 991        .probe          = ab8500_usb_probe,
 992        .remove         = ab8500_usb_remove,
 993        .id_table       = ab8500_usb_devtype,
 994        .driver         = {
 995                .name   = "abx5x0-usb",
 996        },
 997};
 998
 999static int __init ab8500_usb_init(void)
1000{
1001        return platform_driver_register(&ab8500_usb_driver);
1002}
1003subsys_initcall(ab8500_usb_init);
1004
1005static void __exit ab8500_usb_exit(void)
1006{
1007        platform_driver_unregister(&ab8500_usb_driver);
1008}
1009module_exit(ab8500_usb_exit);
1010
1011MODULE_AUTHOR("ST-Ericsson AB");
1012MODULE_DESCRIPTION("AB8500 family usb transceiver driver");
1013MODULE_LICENSE("GPL");
1014