1/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause) */ 2/* 3 * This file is provided under a dual BSD/GPLv2 license. When using or 4 * redistributing this file, you may do so under either license. 5 * 6 * Copyright(c) 2018 Intel Corporation. All rights reserved. 7 */ 8 9#ifndef __INCLUDE_SOUND_SOF_DAI_INTEL_H__ 10#define __INCLUDE_SOUND_SOF_DAI_INTEL_H__ 11 12#include <sound/sof/header.h> 13 14 /* ssc1: TINTE */ 15#define SOF_DAI_INTEL_SSP_QUIRK_TINTE (1 << 0) 16 /* ssc1: PINTE */ 17#define SOF_DAI_INTEL_SSP_QUIRK_PINTE (1 << 1) 18 /* ssc2: SMTATF */ 19#define SOF_DAI_INTEL_SSP_QUIRK_SMTATF (1 << 2) 20 /* ssc2: MMRATF */ 21#define SOF_DAI_INTEL_SSP_QUIRK_MMRATF (1 << 3) 22 /* ssc2: PSPSTWFDFD */ 23#define SOF_DAI_INTEL_SSP_QUIRK_PSPSTWFDFD (1 << 4) 24 /* ssc2: PSPSRWFDFD */ 25#define SOF_DAI_INTEL_SSP_QUIRK_PSPSRWFDFD (1 << 5) 26/* ssc1: LBM */ 27#define SOF_DAI_INTEL_SSP_QUIRK_LBM (1 << 6) 28 29 /* here is the possibility to define others aux macros */ 30 31#define SOF_DAI_INTEL_SSP_FRAME_PULSE_WIDTH_MAX 38 32#define SOF_DAI_INTEL_SSP_SLOT_PADDING_MAX 31 33 34/* SSP clocks control settings 35 * 36 * Macros for clks_control field in sof_ipc_dai_ssp_params struct. 37 */ 38 39/* mclk 0 disable */ 40#define SOF_DAI_INTEL_SSP_MCLK_0_DISABLE BIT(0) 41/* mclk 1 disable */ 42#define SOF_DAI_INTEL_SSP_MCLK_1_DISABLE BIT(1) 43/* mclk keep active */ 44#define SOF_DAI_INTEL_SSP_CLKCTRL_MCLK_KA BIT(2) 45/* bclk keep active */ 46#define SOF_DAI_INTEL_SSP_CLKCTRL_BCLK_KA BIT(3) 47/* fs keep active */ 48#define SOF_DAI_INTEL_SSP_CLKCTRL_FS_KA BIT(4) 49/* bclk idle */ 50#define SOF_DAI_INTEL_SSP_CLKCTRL_BCLK_IDLE_HIGH BIT(5) 51 52/* DMIC max. four controllers for eight microphone channels */ 53#define SOF_DAI_INTEL_DMIC_NUM_CTRL 4 54 55/* SSP Configuration Request - SOF_IPC_DAI_SSP_CONFIG */ 56struct sof_ipc_dai_ssp_params { 57 struct sof_ipc_hdr hdr; 58 uint16_t reserved1; 59 uint16_t mclk_id; 60 61 uint32_t mclk_rate; /* mclk frequency in Hz */ 62 uint32_t fsync_rate; /* fsync frequency in Hz */ 63 uint32_t bclk_rate; /* bclk frequency in Hz */ 64 65 /* TDM */ 66 uint32_t tdm_slots; 67 uint32_t rx_slots; 68 uint32_t tx_slots; 69 70 /* data */ 71 uint32_t sample_valid_bits; 72 uint16_t tdm_slot_width; 73 uint16_t reserved2; /* alignment */ 74 75 /* MCLK */ 76 uint32_t mclk_direction; 77 78 uint16_t frame_pulse_width; 79 uint16_t tdm_per_slot_padding_flag; 80 uint32_t clks_control; 81 uint32_t quirks; 82 uint32_t bclk_delay; /* guaranteed time (ms) for which BCLK 83 * will be driven, before sending data 84 */ 85} __packed; 86 87/* HDA Configuration Request - SOF_IPC_DAI_HDA_CONFIG */ 88struct sof_ipc_dai_hda_params { 89 struct sof_ipc_hdr hdr; 90 uint32_t link_dma_ch; 91 uint32_t rate; 92 uint32_t channels; 93} __packed; 94 95/* ALH Configuration Request - SOF_IPC_DAI_ALH_CONFIG */ 96struct sof_ipc_dai_alh_params { 97 struct sof_ipc_hdr hdr; 98 uint32_t stream_id; 99 uint32_t rate; 100 uint32_t channels; 101 102 /* reserved for future use */ 103 uint32_t reserved[13]; 104} __packed; 105 106/* DMIC Configuration Request - SOF_IPC_DAI_DMIC_CONFIG */ 107 108/* This struct is defined per 2ch PDM controller available in the platform. 109 * Normally it is sufficient to set the used microphone specific enables to 1 110 * and keep other parameters as zero. The customizations are: 111 * 112 * 1. If a device mixes different microphones types with different polarity 113 * and/or the absolute polarity matters the PCM signal from a microphone 114 * can be inverted with the controls. 115 * 116 * 2. If the microphones in a stereo pair do not appear in captured stream 117 * in desired order due to board schematics choises they can be swapped with 118 * the clk_edge parameter. 119 * 120 * 3. If PDM bit errors are seen in capture (poor quality) the skew parameter 121 * that delays the sampling time of data by half cycles of DMIC source clock 122 * can be tried for improvement. However there is no guarantee for this to fix 123 * data integrity problems. 124 */ 125struct sof_ipc_dai_dmic_pdm_ctrl { 126 struct sof_ipc_hdr hdr; 127 uint16_t id; /**< PDM controller ID */ 128 129 uint16_t enable_mic_a; /**< Use A (left) channel mic (0 or 1)*/ 130 uint16_t enable_mic_b; /**< Use B (right) channel mic (0 or 1)*/ 131 132 uint16_t polarity_mic_a; /**< Optionally invert mic A signal (0 or 1) */ 133 uint16_t polarity_mic_b; /**< Optionally invert mic B signal (0 or 1) */ 134 135 uint16_t clk_edge; /**< Optionally swap data clock edge (0 or 1) */ 136 uint16_t skew; /**< Adjust PDM data sampling vs. clock (0..15) */ 137 138 uint16_t reserved[3]; /**< Make sure the total size is 4 bytes aligned */ 139} __packed; 140 141/* This struct contains the global settings for all 2ch PDM controllers. The 142 * version number used in configuration data is checked vs. version used by 143 * device driver src/drivers/dmic.c need to match. It is incremented from 144 * initial value 1 if updates done for the to driver would alter the operation 145 * of the microphone. 146 * 147 * Note: The microphone clock (pdmclk_min, pdmclk_max, duty_min, duty_max) 148 * parameters need to be set as defined in microphone data sheet. E.g. clock 149 * range 1.0 - 3.2 MHz is usually supported microphones. Some microphones are 150 * multi-mode capable and there may be denied mic clock frequencies between 151 * the modes. In such case set the clock range limits of the desired mode to 152 * avoid the driver to set clock to an illegal rate. 153 * 154 * The duty cycle could be set to 48-52% if not known. Generally these 155 * parameters can be altered within data sheet specified limits to match 156 * required audio application performance power. 157 * 158 * The microphone clock needs to be usually about 50-80 times the used audio 159 * sample rate. With highest sample rates above 48 kHz this can relaxed 160 * somewhat. 161 * 162 * The parameter wake_up_time describes how long time the microphone needs 163 * for the data line to produce valid output from mic clock start. The driver 164 * will mute the captured audio for the given time. The min_clock_on_time 165 * parameter is used to prevent too short clock bursts to happen. The driver 166 * will keep the clock active after capture stop if this time is not yet 167 * met. The unit for both is microseconds (us). Exceed of 100 ms will be 168 * treated as an error. 169 */ 170struct sof_ipc_dai_dmic_params { 171 struct sof_ipc_hdr hdr; 172 uint32_t driver_ipc_version; /**< Version (1..N) */ 173 174 uint32_t pdmclk_min; /**< Minimum microphone clock in Hz (100000..N) */ 175 uint32_t pdmclk_max; /**< Maximum microphone clock in Hz (min...N) */ 176 177 uint32_t fifo_fs; /**< FIFO sample rate in Hz (8000..96000) */ 178 uint32_t reserved_1; /**< Reserved */ 179 uint16_t fifo_bits; /**< FIFO word length (16 or 32) */ 180 uint16_t fifo_bits_b; /**< Deprecated since firmware ABI 3.0.1 */ 181 182 uint16_t duty_min; /**< Min. mic clock duty cycle in % (20..80) */ 183 uint16_t duty_max; /**< Max. mic clock duty cycle in % (min..80) */ 184 185 uint32_t num_pdm_active; /**< Number of active pdm controllers. */ 186 /**< Range is 1..SOF_DAI_INTEL_DMIC_NUM_CTRL */ 187 188 uint32_t wake_up_time; /**< Time from clock start to data (us) */ 189 uint32_t min_clock_on_time; /**< Min. time that clk is kept on (us) */ 190 uint32_t unmute_ramp_time; /**< Length of logarithmic gain ramp (ms) */ 191 192 /* reserved for future use */ 193 uint32_t reserved[5]; 194 195 /**< PDM controllers configuration */ 196 struct sof_ipc_dai_dmic_pdm_ctrl pdm[SOF_DAI_INTEL_DMIC_NUM_CTRL]; 197} __packed; 198 199#endif 200