linux/sound/pci/ice1712/juli.c
<<
>>
Prefs
   1// SPDX-License-Identifier: GPL-2.0-or-later
   2/*
   3 *   ALSA driver for ICEnsemble VT1724 (Envy24HT)
   4 *
   5 *   Lowlevel functions for ESI Juli@ cards
   6 *
   7 *      Copyright (c) 2004 Jaroslav Kysela <perex@perex.cz>
   8 *                    2008 Pavel Hofman <dustin@seznam.cz>
   9 */
  10
  11#include <linux/delay.h>
  12#include <linux/interrupt.h>
  13#include <linux/init.h>
  14#include <linux/slab.h>
  15#include <linux/string.h>
  16#include <sound/core.h>
  17#include <sound/tlv.h>
  18
  19#include "ice1712.h"
  20#include "envy24ht.h"
  21#include "juli.h"
  22
  23struct juli_spec {
  24        struct ak4114 *ak4114;
  25        unsigned int analog:1;
  26};
  27
  28/*
  29 * chip addresses on I2C bus
  30 */
  31#define AK4114_ADDR             0x20            /* S/PDIF receiver */
  32#define AK4358_ADDR             0x22            /* DAC */
  33
  34/*
  35 * Juli does not use the standard ICE1724 clock scheme. Juli's ice1724 chip is
  36 * supplied by external clock provided by Xilinx array and MK73-1 PLL frequency
  37 * multiplier. Actual frequency is set by ice1724 GPIOs hooked to the Xilinx.
  38 *
  39 * The clock circuitry is supplied by the two ice1724 crystals. This
  40 * arrangement allows to generate independent clock signal for AK4114's input
  41 * rate detection circuit. As a result, Juli, unlike most other
  42 * ice1724+ak4114-based cards, detects spdif input rate correctly.
  43 * This fact is applied in the driver, allowing to modify PCM stream rate
  44 * parameter according to the actual input rate.
  45 *
  46 * Juli uses the remaining three stereo-channels of its DAC to optionally
  47 * monitor analog input, digital input, and digital output. The corresponding
  48 * I2S signals are routed by Xilinx, controlled by GPIOs.
  49 *
  50 * The master mute is implemented using output muting transistors (GPIO) in
  51 * combination with smuting the DAC.
  52 *
  53 * The card itself has no HW master volume control, implemented using the
  54 * vmaster control.
  55 *
  56 * TODO:
  57 * researching and fixing the input monitors
  58 */
  59
  60/*
  61 * GPIO pins
  62 */
  63#define GPIO_FREQ_MASK          (3<<0)
  64#define GPIO_FREQ_32KHZ         (0<<0)
  65#define GPIO_FREQ_44KHZ         (1<<0)
  66#define GPIO_FREQ_48KHZ         (2<<0)
  67#define GPIO_MULTI_MASK         (3<<2)
  68#define GPIO_MULTI_4X           (0<<2)
  69#define GPIO_MULTI_2X           (1<<2)
  70#define GPIO_MULTI_1X           (2<<2)          /* also external */
  71#define GPIO_MULTI_HALF         (3<<2)
  72#define GPIO_INTERNAL_CLOCK     (1<<4)          /* 0 = external, 1 = internal */
  73#define GPIO_CLOCK_MASK         (1<<4)
  74#define GPIO_ANALOG_PRESENT     (1<<5)          /* RO only: 0 = present */
  75#define GPIO_RXMCLK_SEL         (1<<7)          /* must be 0 */
  76#define GPIO_AK5385A_CKS0       (1<<8)
  77#define GPIO_AK5385A_DFS1       (1<<9)
  78#define GPIO_AK5385A_DFS0       (1<<10)
  79#define GPIO_DIGOUT_MONITOR     (1<<11)         /* 1 = active */
  80#define GPIO_DIGIN_MONITOR      (1<<12)         /* 1 = active */
  81#define GPIO_ANAIN_MONITOR      (1<<13)         /* 1 = active */
  82#define GPIO_AK5385A_CKS1       (1<<14)         /* must be 0 */
  83#define GPIO_MUTE_CONTROL       (1<<15)         /* output mute, 1 = muted */
  84
  85#define GPIO_RATE_MASK          (GPIO_FREQ_MASK | GPIO_MULTI_MASK | \
  86                GPIO_CLOCK_MASK)
  87#define GPIO_AK5385A_MASK       (GPIO_AK5385A_CKS0 | GPIO_AK5385A_DFS0 | \
  88                GPIO_AK5385A_DFS1 | GPIO_AK5385A_CKS1)
  89
  90#define JULI_PCM_RATE   (SNDRV_PCM_RATE_16000 | SNDRV_PCM_RATE_22050 | \
  91                SNDRV_PCM_RATE_32000 | SNDRV_PCM_RATE_44100 | \
  92                SNDRV_PCM_RATE_48000 | SNDRV_PCM_RATE_64000 | \
  93                SNDRV_PCM_RATE_88200 | SNDRV_PCM_RATE_96000 | \
  94                SNDRV_PCM_RATE_176400 | SNDRV_PCM_RATE_192000)
  95
  96#define GPIO_RATE_16000         (GPIO_FREQ_32KHZ | GPIO_MULTI_HALF | \
  97                GPIO_INTERNAL_CLOCK)
  98#define GPIO_RATE_22050         (GPIO_FREQ_44KHZ | GPIO_MULTI_HALF | \
  99                GPIO_INTERNAL_CLOCK)
 100#define GPIO_RATE_24000         (GPIO_FREQ_48KHZ | GPIO_MULTI_HALF | \
 101                GPIO_INTERNAL_CLOCK)
 102#define GPIO_RATE_32000         (GPIO_FREQ_32KHZ | GPIO_MULTI_1X | \
 103                GPIO_INTERNAL_CLOCK)
 104#define GPIO_RATE_44100         (GPIO_FREQ_44KHZ | GPIO_MULTI_1X | \
 105                GPIO_INTERNAL_CLOCK)
 106#define GPIO_RATE_48000         (GPIO_FREQ_48KHZ | GPIO_MULTI_1X | \
 107                GPIO_INTERNAL_CLOCK)
 108#define GPIO_RATE_64000         (GPIO_FREQ_32KHZ | GPIO_MULTI_2X | \
 109                GPIO_INTERNAL_CLOCK)
 110#define GPIO_RATE_88200         (GPIO_FREQ_44KHZ | GPIO_MULTI_2X | \
 111                GPIO_INTERNAL_CLOCK)
 112#define GPIO_RATE_96000         (GPIO_FREQ_48KHZ | GPIO_MULTI_2X | \
 113                GPIO_INTERNAL_CLOCK)
 114#define GPIO_RATE_176400        (GPIO_FREQ_44KHZ | GPIO_MULTI_4X | \
 115                GPIO_INTERNAL_CLOCK)
 116#define GPIO_RATE_192000        (GPIO_FREQ_48KHZ | GPIO_MULTI_4X | \
 117                GPIO_INTERNAL_CLOCK)
 118
 119/*
 120 * Initial setup of the conversion array GPIO <-> rate
 121 */
 122static const unsigned int juli_rates[] = {
 123        16000, 22050, 24000, 32000,
 124        44100, 48000, 64000, 88200,
 125        96000, 176400, 192000,
 126};
 127
 128static const unsigned int gpio_vals[] = {
 129        GPIO_RATE_16000, GPIO_RATE_22050, GPIO_RATE_24000, GPIO_RATE_32000,
 130        GPIO_RATE_44100, GPIO_RATE_48000, GPIO_RATE_64000, GPIO_RATE_88200,
 131        GPIO_RATE_96000, GPIO_RATE_176400, GPIO_RATE_192000,
 132};
 133
 134static const struct snd_pcm_hw_constraint_list juli_rates_info = {
 135        .count = ARRAY_SIZE(juli_rates),
 136        .list = juli_rates,
 137        .mask = 0,
 138};
 139
 140static int get_gpio_val(int rate)
 141{
 142        int i;
 143        for (i = 0; i < ARRAY_SIZE(juli_rates); i++)
 144                if (juli_rates[i] == rate)
 145                        return gpio_vals[i];
 146        return 0;
 147}
 148
 149static void juli_ak4114_write(void *private_data, unsigned char reg,
 150                                unsigned char val)
 151{
 152        snd_vt1724_write_i2c((struct snd_ice1712 *)private_data, AK4114_ADDR,
 153                                reg, val);
 154}
 155
 156static unsigned char juli_ak4114_read(void *private_data, unsigned char reg)
 157{
 158        return snd_vt1724_read_i2c((struct snd_ice1712 *)private_data,
 159                                        AK4114_ADDR, reg);
 160}
 161
 162/*
 163 * If SPDIF capture and slaved to SPDIF-IN, setting runtime rate
 164 * to the external rate
 165 */
 166static void juli_spdif_in_open(struct snd_ice1712 *ice,
 167                                struct snd_pcm_substream *substream)
 168{
 169        struct juli_spec *spec = ice->spec;
 170        struct snd_pcm_runtime *runtime = substream->runtime;
 171        int rate;
 172
 173        if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK ||
 174                        !ice->is_spdif_master(ice))
 175                return;
 176        rate = snd_ak4114_external_rate(spec->ak4114);
 177        if (rate >= runtime->hw.rate_min && rate <= runtime->hw.rate_max) {
 178                runtime->hw.rate_min = rate;
 179                runtime->hw.rate_max = rate;
 180        }
 181}
 182
 183/*
 184 * AK4358 section
 185 */
 186
 187static void juli_akm_lock(struct snd_akm4xxx *ak, int chip)
 188{
 189}
 190
 191static void juli_akm_unlock(struct snd_akm4xxx *ak, int chip)
 192{
 193}
 194
 195static void juli_akm_write(struct snd_akm4xxx *ak, int chip,
 196                           unsigned char addr, unsigned char data)
 197{
 198        struct snd_ice1712 *ice = ak->private_data[0];
 199         
 200        if (snd_BUG_ON(chip))
 201                return;
 202        snd_vt1724_write_i2c(ice, AK4358_ADDR, addr, data);
 203}
 204
 205/*
 206 * change the rate of envy24HT, AK4358, AK5385
 207 */
 208static void juli_akm_set_rate_val(struct snd_akm4xxx *ak, unsigned int rate)
 209{
 210        unsigned char old, tmp, ak4358_dfs;
 211        unsigned int ak5385_pins, old_gpio, new_gpio;
 212        struct snd_ice1712 *ice = ak->private_data[0];
 213        struct juli_spec *spec = ice->spec;
 214
 215        if (rate == 0)  /* no hint - S/PDIF input is master or the new spdif
 216                           input rate undetected, simply return */
 217                return;
 218
 219        /* adjust DFS on codecs */
 220        if (rate > 96000)  {
 221                ak4358_dfs = 2;
 222                ak5385_pins = GPIO_AK5385A_DFS1 | GPIO_AK5385A_CKS0;
 223        } else if (rate > 48000) {
 224                ak4358_dfs = 1;
 225                ak5385_pins = GPIO_AK5385A_DFS0;
 226        } else {
 227                ak4358_dfs = 0;
 228                ak5385_pins = 0;
 229        }
 230        /* AK5385 first, since it requires cold reset affecting both codecs */
 231        old_gpio = ice->gpio.get_data(ice);
 232        new_gpio =  (old_gpio & ~GPIO_AK5385A_MASK) | ak5385_pins;
 233        /* dev_dbg(ice->card->dev, "JULI - ak5385 set_rate_val: new gpio 0x%x\n",
 234                new_gpio); */
 235        ice->gpio.set_data(ice, new_gpio);
 236
 237        /* cold reset */
 238        old = inb(ICEMT1724(ice, AC97_CMD));
 239        outb(old | VT1724_AC97_COLD, ICEMT1724(ice, AC97_CMD));
 240        udelay(1);
 241        outb(old & ~VT1724_AC97_COLD, ICEMT1724(ice, AC97_CMD));
 242
 243        /* AK4358 */
 244        /* set new value, reset DFS */
 245        tmp = snd_akm4xxx_get(ak, 0, 2);
 246        snd_akm4xxx_reset(ak, 1);
 247        tmp = snd_akm4xxx_get(ak, 0, 2);
 248        tmp &= ~(0x03 << 4);
 249        tmp |= ak4358_dfs << 4;
 250        snd_akm4xxx_set(ak, 0, 2, tmp);
 251        snd_akm4xxx_reset(ak, 0);
 252
 253        /* reinit ak4114 */
 254        snd_ak4114_reinit(spec->ak4114);
 255}
 256
 257#define AK_DAC(xname, xch)      { .name = xname, .num_channels = xch }
 258#define PCM_VOLUME              "PCM Playback Volume"
 259#define MONITOR_AN_IN_VOLUME    "Monitor Analog In Volume"
 260#define MONITOR_DIG_IN_VOLUME   "Monitor Digital In Volume"
 261#define MONITOR_DIG_OUT_VOLUME  "Monitor Digital Out Volume"
 262
 263static const struct snd_akm4xxx_dac_channel juli_dac[] = {
 264        AK_DAC(PCM_VOLUME, 2),
 265        AK_DAC(MONITOR_AN_IN_VOLUME, 2),
 266        AK_DAC(MONITOR_DIG_OUT_VOLUME, 2),
 267        AK_DAC(MONITOR_DIG_IN_VOLUME, 2),
 268};
 269
 270
 271static const struct snd_akm4xxx akm_juli_dac = {
 272        .type = SND_AK4358,
 273        .num_dacs = 8,  /* DAC1 - analog out
 274                           DAC2 - analog in monitor
 275                           DAC3 - digital out monitor
 276                           DAC4 - digital in monitor
 277                         */
 278        .ops = {
 279                .lock = juli_akm_lock,
 280                .unlock = juli_akm_unlock,
 281                .write = juli_akm_write,
 282                .set_rate_val = juli_akm_set_rate_val
 283        },
 284        .dac_info = juli_dac,
 285};
 286
 287#define juli_mute_info          snd_ctl_boolean_mono_info
 288
 289static int juli_mute_get(struct snd_kcontrol *kcontrol,
 290                struct snd_ctl_elem_value *ucontrol)
 291{
 292        struct snd_ice1712 *ice = snd_kcontrol_chip(kcontrol);
 293        unsigned int val;
 294        val = ice->gpio.get_data(ice) & (unsigned int) kcontrol->private_value;
 295        if (kcontrol->private_value == GPIO_MUTE_CONTROL)
 296                /* val 0 = signal on */
 297                ucontrol->value.integer.value[0] = (val) ? 0 : 1;
 298        else
 299                /* val 1 = signal on */
 300                ucontrol->value.integer.value[0] = (val) ? 1 : 0;
 301        return 0;
 302}
 303
 304static int juli_mute_put(struct snd_kcontrol *kcontrol,
 305                struct snd_ctl_elem_value *ucontrol)
 306{
 307        struct snd_ice1712 *ice = snd_kcontrol_chip(kcontrol);
 308        unsigned int old_gpio, new_gpio;
 309        old_gpio = ice->gpio.get_data(ice);
 310        if (ucontrol->value.integer.value[0]) {
 311                /* unmute */
 312                if (kcontrol->private_value == GPIO_MUTE_CONTROL) {
 313                        /* 0 = signal on */
 314                        new_gpio = old_gpio & ~GPIO_MUTE_CONTROL;
 315                        /* un-smuting DAC */
 316                        snd_akm4xxx_write(ice->akm, 0, 0x01, 0x01);
 317                } else
 318                        /* 1 = signal on */
 319                        new_gpio =  old_gpio |
 320                                (unsigned int) kcontrol->private_value;
 321        } else {
 322                /* mute */
 323                if (kcontrol->private_value == GPIO_MUTE_CONTROL) {
 324                        /* 1 = signal off */
 325                        new_gpio = old_gpio | GPIO_MUTE_CONTROL;
 326                        /* smuting DAC */
 327                        snd_akm4xxx_write(ice->akm, 0, 0x01, 0x03);
 328                } else
 329                        /* 0 = signal off */
 330                        new_gpio =  old_gpio &
 331                                ~((unsigned int) kcontrol->private_value);
 332        }
 333        /* dev_dbg(ice->card->dev,
 334                "JULI - mute/unmute: control_value: 0x%x, old_gpio: 0x%x, "
 335                "new_gpio 0x%x\n",
 336                (unsigned int)ucontrol->value.integer.value[0], old_gpio,
 337                new_gpio); */
 338        if (old_gpio != new_gpio) {
 339                ice->gpio.set_data(ice, new_gpio);
 340                return 1;
 341        }
 342        /* no change */
 343        return 0;
 344}
 345
 346static const struct snd_kcontrol_new juli_mute_controls[] = {
 347        {
 348                .iface = SNDRV_CTL_ELEM_IFACE_MIXER,
 349                .name = "Master Playback Switch",
 350                .info = juli_mute_info,
 351                .get = juli_mute_get,
 352                .put = juli_mute_put,
 353                .private_value = GPIO_MUTE_CONTROL,
 354        },
 355        /* Although the following functionality respects the succint NDA'd
 356         * documentation from the card manufacturer, and the same way of
 357         * operation is coded in OSS Juli driver, only Digital Out monitor
 358         * seems to work. Surprisingly, Analog input monitor outputs Digital
 359         * output data. The two are independent, as enabling both doubles
 360         * volume of the monitor sound.
 361         *
 362         * Checking traces on the board suggests the functionality described
 363         * by the manufacturer is correct - I2S from ADC and AK4114
 364         * go to ICE as well as to Xilinx, I2S inputs of DAC2,3,4 (the monitor
 365         * inputs) are fed from Xilinx.
 366         *
 367         * I even checked traces on board and coded a support in driver for
 368         * an alternative possibility - the unused I2S ICE output channels
 369         * switched to HW-IN/SPDIF-IN and providing the monitoring signal to
 370         * the DAC - to no avail. The I2S outputs seem to be unconnected.
 371         *
 372         * The windows driver supports the monitoring correctly.
 373         */
 374        {
 375                .iface = SNDRV_CTL_ELEM_IFACE_MIXER,
 376                .name = "Monitor Analog In Switch",
 377                .info = juli_mute_info,
 378                .get = juli_mute_get,
 379                .put = juli_mute_put,
 380                .private_value = GPIO_ANAIN_MONITOR,
 381        },
 382        {
 383                .iface = SNDRV_CTL_ELEM_IFACE_MIXER,
 384                .name = "Monitor Digital Out Switch",
 385                .info = juli_mute_info,
 386                .get = juli_mute_get,
 387                .put = juli_mute_put,
 388                .private_value = GPIO_DIGOUT_MONITOR,
 389        },
 390        {
 391                .iface = SNDRV_CTL_ELEM_IFACE_MIXER,
 392                .name = "Monitor Digital In Switch",
 393                .info = juli_mute_info,
 394                .get = juli_mute_get,
 395                .put = juli_mute_put,
 396                .private_value = GPIO_DIGIN_MONITOR,
 397        },
 398};
 399
 400static const char * const follower_vols[] = {
 401        PCM_VOLUME,
 402        MONITOR_AN_IN_VOLUME,
 403        MONITOR_DIG_IN_VOLUME,
 404        MONITOR_DIG_OUT_VOLUME,
 405        NULL
 406};
 407
 408static
 409DECLARE_TLV_DB_SCALE(juli_master_db_scale, -6350, 50, 1);
 410
 411static struct snd_kcontrol *ctl_find(struct snd_card *card,
 412                                     const char *name)
 413{
 414        struct snd_ctl_elem_id sid = {0};
 415
 416        strscpy(sid.name, name, sizeof(sid.name));
 417        sid.iface = SNDRV_CTL_ELEM_IFACE_MIXER;
 418        return snd_ctl_find_id(card, &sid);
 419}
 420
 421static void add_followers(struct snd_card *card,
 422                          struct snd_kcontrol *master,
 423                          const char * const *list)
 424{
 425        for (; *list; list++) {
 426                struct snd_kcontrol *follower = ctl_find(card, *list);
 427                /* dev_dbg(card->dev, "add_followers - %s\n", *list); */
 428                if (follower) {
 429                        /* dev_dbg(card->dev, "follower %s found\n", *list); */
 430                        snd_ctl_add_follower(master, follower);
 431                }
 432        }
 433}
 434
 435static int juli_add_controls(struct snd_ice1712 *ice)
 436{
 437        struct juli_spec *spec = ice->spec;
 438        int err;
 439        unsigned int i;
 440        struct snd_kcontrol *vmaster;
 441
 442        err = snd_ice1712_akm4xxx_build_controls(ice);
 443        if (err < 0)
 444                return err;
 445
 446        for (i = 0; i < ARRAY_SIZE(juli_mute_controls); i++) {
 447                err = snd_ctl_add(ice->card,
 448                                snd_ctl_new1(&juli_mute_controls[i], ice));
 449                if (err < 0)
 450                        return err;
 451        }
 452        /* Create virtual master control */
 453        vmaster = snd_ctl_make_virtual_master("Master Playback Volume",
 454                                              juli_master_db_scale);
 455        if (!vmaster)
 456                return -ENOMEM;
 457        add_followers(ice->card, vmaster, follower_vols);
 458        err = snd_ctl_add(ice->card, vmaster);
 459        if (err < 0)
 460                return err;
 461
 462        /* only capture SPDIF over AK4114 */
 463        return snd_ak4114_build(spec->ak4114, NULL,
 464                        ice->pcm->streams[SNDRV_PCM_STREAM_CAPTURE].substream);
 465}
 466
 467/*
 468 * suspend/resume
 469 * */
 470
 471#ifdef CONFIG_PM_SLEEP
 472static int juli_resume(struct snd_ice1712 *ice)
 473{
 474        struct snd_akm4xxx *ak = ice->akm;
 475        struct juli_spec *spec = ice->spec;
 476        /* akm4358 un-reset, un-mute */
 477        snd_akm4xxx_reset(ak, 0);
 478        /* reinit ak4114 */
 479        snd_ak4114_resume(spec->ak4114);
 480        return 0;
 481}
 482
 483static int juli_suspend(struct snd_ice1712 *ice)
 484{
 485        struct snd_akm4xxx *ak = ice->akm;
 486        struct juli_spec *spec = ice->spec;
 487        /* akm4358 reset and soft-mute */
 488        snd_akm4xxx_reset(ak, 1);
 489        snd_ak4114_suspend(spec->ak4114);
 490        return 0;
 491}
 492#endif
 493
 494/*
 495 * initialize the chip
 496 */
 497
 498static inline int juli_is_spdif_master(struct snd_ice1712 *ice)
 499{
 500        return (ice->gpio.get_data(ice) & GPIO_INTERNAL_CLOCK) ? 0 : 1;
 501}
 502
 503static unsigned int juli_get_rate(struct snd_ice1712 *ice)
 504{
 505        int i;
 506        unsigned char result;
 507
 508        result =  ice->gpio.get_data(ice) & GPIO_RATE_MASK;
 509        for (i = 0; i < ARRAY_SIZE(gpio_vals); i++)
 510                if (gpio_vals[i] == result)
 511                        return juli_rates[i];
 512        return 0;
 513}
 514
 515/* setting new rate */
 516static void juli_set_rate(struct snd_ice1712 *ice, unsigned int rate)
 517{
 518        unsigned int old, new;
 519        unsigned char val;
 520
 521        old = ice->gpio.get_data(ice);
 522        new =  (old & ~GPIO_RATE_MASK) | get_gpio_val(rate);
 523        /* dev_dbg(ice->card->dev, "JULI - set_rate: old %x, new %x\n",
 524                        old & GPIO_RATE_MASK,
 525                        new & GPIO_RATE_MASK); */
 526
 527        ice->gpio.set_data(ice, new);
 528        /* switching to external clock - supplied by external circuits */
 529        val = inb(ICEMT1724(ice, RATE));
 530        outb(val | VT1724_SPDIF_MASTER, ICEMT1724(ice, RATE));
 531}
 532
 533static inline unsigned char juli_set_mclk(struct snd_ice1712 *ice,
 534                                          unsigned int rate)
 535{
 536        /* no change in master clock */
 537        return 0;
 538}
 539
 540/* setting clock to external - SPDIF */
 541static int juli_set_spdif_clock(struct snd_ice1712 *ice, int type)
 542{
 543        unsigned int old;
 544        old = ice->gpio.get_data(ice);
 545        /* external clock (= 0), multiply 1x, 48kHz */
 546        ice->gpio.set_data(ice, (old & ~GPIO_RATE_MASK) | GPIO_MULTI_1X |
 547                        GPIO_FREQ_48KHZ);
 548        return 0;
 549}
 550
 551/* Called when ak4114 detects change in the input SPDIF stream */
 552static void juli_ak4114_change(struct ak4114 *ak4114, unsigned char c0,
 553                               unsigned char c1)
 554{
 555        struct snd_ice1712 *ice = ak4114->change_callback_private;
 556        int rate;
 557        if (ice->is_spdif_master(ice) && c1) {
 558                /* only for SPDIF master mode, rate was changed */
 559                rate = snd_ak4114_external_rate(ak4114);
 560                /* dev_dbg(ice->card->dev, "ak4114 - input rate changed to %d\n",
 561                                rate); */
 562                juli_akm_set_rate_val(ice->akm, rate);
 563        }
 564}
 565
 566static int juli_init(struct snd_ice1712 *ice)
 567{
 568        static const unsigned char ak4114_init_vals[] = {
 569                /* AK4117_REG_PWRDN */  AK4114_RST | AK4114_PWN |
 570                                        AK4114_OCKS0 | AK4114_OCKS1,
 571                /* AK4114_REQ_FORMAT */ AK4114_DIF_I24I2S,
 572                /* AK4114_REG_IO0 */    AK4114_TX1E,
 573                /* AK4114_REG_IO1 */    AK4114_EFH_1024 | AK4114_DIT |
 574                                        AK4114_IPS(1),
 575                /* AK4114_REG_INT0_MASK */ 0,
 576                /* AK4114_REG_INT1_MASK */ 0
 577        };
 578        static const unsigned char ak4114_init_txcsb[] = {
 579                0x41, 0x02, 0x2c, 0x00, 0x00
 580        };
 581        int err;
 582        struct juli_spec *spec;
 583        struct snd_akm4xxx *ak;
 584
 585        spec = kzalloc(sizeof(*spec), GFP_KERNEL);
 586        if (!spec)
 587                return -ENOMEM;
 588        ice->spec = spec;
 589
 590        err = snd_ak4114_create(ice->card,
 591                                juli_ak4114_read,
 592                                juli_ak4114_write,
 593                                ak4114_init_vals, ak4114_init_txcsb,
 594                                ice, &spec->ak4114);
 595        if (err < 0)
 596                return err;
 597        /* callback for codecs rate setting */
 598        spec->ak4114->change_callback = juli_ak4114_change;
 599        spec->ak4114->change_callback_private = ice;
 600        /* AK4114 in Juli can detect external rate correctly */
 601        spec->ak4114->check_flags = 0;
 602
 603#if 0
 604/*
 605 * it seems that the analog doughter board detection does not work reliably, so
 606 * force the analog flag; it should be very rare (if ever) to come at Juli@
 607 * used without the analog daughter board
 608 */
 609        spec->analog = (ice->gpio.get_data(ice) & GPIO_ANALOG_PRESENT) ? 0 : 1;
 610#else
 611        spec->analog = 1;
 612#endif
 613
 614        if (spec->analog) {
 615                dev_info(ice->card->dev, "juli@: analog I/O detected\n");
 616                ice->num_total_dacs = 2;
 617                ice->num_total_adcs = 2;
 618
 619                ice->akm = kzalloc(sizeof(struct snd_akm4xxx), GFP_KERNEL);
 620                ak = ice->akm;
 621                if (!ak)
 622                        return -ENOMEM;
 623                ice->akm_codecs = 1;
 624                err = snd_ice1712_akm4xxx_init(ak, &akm_juli_dac, NULL, ice);
 625                if (err < 0)
 626                        return err;
 627        }
 628
 629        /* juli is clocked by Xilinx array */
 630        ice->hw_rates = &juli_rates_info;
 631        ice->is_spdif_master = juli_is_spdif_master;
 632        ice->get_rate = juli_get_rate;
 633        ice->set_rate = juli_set_rate;
 634        ice->set_mclk = juli_set_mclk;
 635        ice->set_spdif_clock = juli_set_spdif_clock;
 636
 637        ice->spdif.ops.open = juli_spdif_in_open;
 638
 639#ifdef CONFIG_PM_SLEEP
 640        ice->pm_resume = juli_resume;
 641        ice->pm_suspend = juli_suspend;
 642        ice->pm_suspend_enabled = 1;
 643#endif
 644
 645        return 0;
 646}
 647
 648
 649/*
 650 * Juli@ boards don't provide the EEPROM data except for the vendor IDs.
 651 * hence the driver needs to sets up it properly.
 652 */
 653
 654static const unsigned char juli_eeprom[] = {
 655        [ICE_EEP2_SYSCONF]     = 0x2b,  /* clock 512, mpu401, 1xADC, 1xDACs,
 656                                           SPDIF in */
 657        [ICE_EEP2_ACLINK]      = 0x80,  /* I2S */
 658        [ICE_EEP2_I2S]         = 0xf8,  /* vol, 96k, 24bit, 192k */
 659        [ICE_EEP2_SPDIF]       = 0xc3,  /* out-en, out-int, spdif-in */
 660        [ICE_EEP2_GPIO_DIR]    = 0x9f,  /* 5, 6:inputs; 7, 4-0 outputs*/
 661        [ICE_EEP2_GPIO_DIR1]   = 0xff,
 662        [ICE_EEP2_GPIO_DIR2]   = 0x7f,
 663        [ICE_EEP2_GPIO_MASK]   = 0x60,  /* 5, 6: locked; 7, 4-0 writable */
 664        [ICE_EEP2_GPIO_MASK1]  = 0x00,  /* 0-7 writable */
 665        [ICE_EEP2_GPIO_MASK2]  = 0x7f,
 666        [ICE_EEP2_GPIO_STATE]  = GPIO_FREQ_48KHZ | GPIO_MULTI_1X |
 667               GPIO_INTERNAL_CLOCK,     /* internal clock, multiple 1x, 48kHz*/
 668        [ICE_EEP2_GPIO_STATE1] = 0x00,  /* unmuted */
 669        [ICE_EEP2_GPIO_STATE2] = 0x00,
 670};
 671
 672/* entry point */
 673struct snd_ice1712_card_info snd_vt1724_juli_cards[] = {
 674        {
 675                .subvendor = VT1724_SUBDEVICE_JULI,
 676                .name = "ESI Juli@",
 677                .model = "juli",
 678                .chip_init = juli_init,
 679                .build_controls = juli_add_controls,
 680                .eeprom_size = sizeof(juli_eeprom),
 681                .eeprom_data = juli_eeprom,
 682        },
 683        { } /* terminator */
 684};
 685