1/* 2 * (C) Copyright 2002 3 * Wolfgang Grandegger, DENX Software Engineering, wg@denx.de. 4 * 5 * See file CREDITS for list of people who contributed to this 6 * project. 7 * 8 * This program is free software; you can redistribute it and/or 9 * modify it under the terms of the GNU General Public License as 10 * published by the Free Software Foundation; either version 2 of 11 * the License, or (at your option) any later version. 12 * 13 * This program is distributed in the hope that it will be useful, 14 * but WITHOUT ANY WARRANTY; without even the implied warranty of 15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 16 * GNU General Public License for more details. 17 * 18 * You should have received a copy of the GNU General Public License 19 * along with this program; if not, write to the Free Software 20 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 21 * MA 02111-1307 USA 22 */ 23 24/* ------------------------------------------------------------------------- */ 25 26/* 27 * board/config.h - configuration options, board specific 28 */ 29 30#ifndef __CONFIG_H 31#define __CONFIG_H 32 33/* 34 * High Level Configuration Options 35 * (easy to change) 36 */ 37 38#define CONFIG_MPC824X 1 39#define CONFIG_MPC8240 1 40#define CONFIG_PN62 1 41 42#define CONFIG_CONS_INDEX 1 43 44 45/* 46 * BOOTP options 47 */ 48#define CONFIG_BOOTP_BOOTFILESIZE 49#define CONFIG_BOOTP_BOOTPATH 50#define CONFIG_BOOTP_GATEWAY 51#define CONFIG_BOOTP_HOSTNAME 52 53 54/* 55 * Command line configuration. 56 */ 57#include <config_cmd_default.h> 58 59#define CONFIG_CMD_PCI 60#define CONFIG_CMD_BSP 61 62#undef CONFIG_CMD_AUTOSCRIPT 63#undef CONFIG_CMD_LOADS 64#undef CONFIG_CMD_ENV 65#undef CONFIG_CMD_FLASH 66#undef CONFIG_CMD_IMLS 67 68 69#define CONFIG_BAUDRATE 19200 /* console baudrate */ 70 71#define CONFIG_BOOTDELAY 1 /* autoboot after n seconds */ 72 73#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ 74 75#define CONFIG_SERVERIP 10.0.0.201 76#define CONFIG_IPADDR 10.0.0.200 77#define CONFIG_ROOTPATH /opt/eldk/ppc_82xx 78#define CONFIG_NETMASK 255.255.255.0 79#undef CONFIG_BOOTARGS 80#if 0 81/* Boot Linux with NFS root filesystem */ 82#define CONFIG_BOOTCOMMAND \ 83 "setenv verify y;" \ 84 "setenv bootargs console=ttyS0,19200 mem=31M quiet " \ 85 "root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ 86 "ip=${ipaddr}:${serverip}::${netmask}:pn62:eth0:off;" \ 87 "loadp 100000; bootm" 88 /* "tftpboot 100000 uImage; bootm" */ 89#else 90/* Boot Linux with RAMdisk based filesystem (initrd, BusyBox) */ 91#define CONFIG_BOOTCOMMAND \ 92 "setenv verify n;" \ 93 "setenv bootargs console=ttyS0,19200 mem=31M quiet " \ 94 "root=/dev/ram rw " \ 95 "ip=${ipaddr}:${serverip}::${netmask}:pn62:eth0:off;" \ 96 "loadp 200000; bootm" 97#endif 98 99/* 100 * Miscellaneous configurable options 101 */ 102#define CFG_LONGHELP 1 /* undef to save memory */ 103#define CFG_PROMPT "=> " /* Monitor Command Prompt */ 104#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ 105#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ 106#define CFG_MAXARGS 16 /* max number of command args */ 107#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ 108#define CFG_LOAD_ADDR 0x00100000 /* default load address */ 109#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ 110 111#define CONFIG_PRAM 1024 /* reserve 1 MB protected RAM */ 112 113#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() on init */ 114 115#define CONFIG_HAS_ETH1 1 /* add support for eth1addr */ 116 117#define CONFIG_SHOW_BOOT_PROGRESS 1 /* Show boot progress on LEDs */ 118 119/* 120 * PCI stuff 121 */ 122#define CONFIG_PCI /* include pci support */ 123#define CONFIG_PCI_PNP /* we need Plug 'n Play */ 124#if 0 125#define CONFIG_PCI_SCAN_SHOW /* show PCI auto-scan at boot */ 126#endif 127 128/* 129 * Networking stuff 130 */ 131#define CONFIG_NET_MULTI /* Multi ethernet cards support */ 132 133#define CONFIG_PCNET /* there are 2 AMD PCnet 79C973 */ 134#define CONFIG_PCNET_79C973 135 136#define _IO_BASE 0xfe000000 /* points to PCI I/O space */ 137 138 139/* 140 * Start addresses for the final memory configuration 141 * (Set up by the startup code) 142 * Please note that CFG_SDRAM_BASE _must_ start at 0 143 */ 144#define CFG_SDRAM_BASE 0x00000000 145#define CFG_MAX_RAM_SIZE 0x10000000 146 147#define CFG_RESET_ADDRESS 0xfff00100 148 149#undef CFG_RAMBOOT 150#define CFG_MONITOR_LEN 0x00030000 151#define CFG_MONITOR_BASE TEXT_BASE 152 153/*#define CFG_GBL_DATA_SIZE 256*/ 154#define CFG_GBL_DATA_SIZE 128 155 156#define CFG_INIT_RAM_ADDR 0x40000000 157#define CFG_INIT_RAM_END 0x1000 158#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) 159 160 161#define CFG_NO_FLASH 1 /* There is no FLASH memory */ 162 163#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ 164#define CONFIG_ENV_OFFSET 0x00004000 /* Offset of Environment Sector */ 165#define CONFIG_ENV_SIZE 0x00002000 /* Total Size of Environment Sector */ 166 167#define CFG_MALLOC_LEN (512 << 10) /* Reserve 512 kB for malloc() */ 168 169#define CFG_MEMTEST_START 0x00004000 /* memtest works on */ 170#define CFG_MEMTEST_END 0x01f00000 /* 0 ... 32 MB in DRAM */ 171 172/* 173 * Serial port configuration 174 */ 175#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } 176 177#define CFG_NS16550 178#define CFG_NS16550_SERIAL 179 180#define CFG_NS16550_REG_SIZE 1 181 182#define CFG_NS16550_CLK 1843200 183 184#define CFG_NS16550_COM1 0xff800008 185#define CFG_NS16550_COM2 0xff800000 186 187/* 188 * Low Level Configuration Settings 189 * (address mappings, register initial values, etc.) 190 * You should know what you are doing if you make changes here. 191 */ 192 193#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ 194#define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER 3 195 196#define CFG_EUMB_ADDR 0xFCE00000 197 198/* MCCR1 */ 199#define CFG_ROMNAL 3 /* rom/flash next access time */ 200#define CFG_ROMFAL 7 /* rom/flash access time */ 201 202/* MCCR2 */ 203#define CFG_ASRISE 6 /* ASRISE in clocks */ 204#define CFG_ASFALL 12 /* ASFALL in clocks */ 205#define CFG_REFINT 5600 /* REFINT in clocks */ 206 207/* MCCR3 */ 208#define CFG_BSTOPRE 0x3cf /* Burst To Precharge */ 209#define CFG_REFREC 2 /* Refresh to activate interval */ 210#define CFG_RDLAT 3 /* data latency from read command */ 211 212/* MCCR4 */ 213#define CFG_PRETOACT 1 /* Precharge to activate interval */ 214#define CFG_ACTTOPRE 3 /* Activate to Precharge interval */ 215#define CFG_ACTORW 2 /* Activate to R/W */ 216#define CFG_SDMODE_CAS_LAT 2 /* SDMODE CAS latency */ 217#define CFG_SDMODE_WRAP 0 /* SDMODE Wrap type */ 218#define CFG_SDMODE_BURSTLEN 2 /* SDMODE Burst length 2=4, 3=8 */ 219#define CFG_REGISTERD_TYPE_BUFFER 1 220 221/* Memory bank settings: 222 * 223 * only bits 20-29 are actually used from these vales to set the 224 * start/qend address the upper two bits will be 0, and the lower 20 225 * bits will be set to 0x00000 for a start address, or 0xfffff for an 226 * end address 227 */ 228#define CFG_BANK0_START 0x00000000 229#define CFG_BANK0_END (CFG_MAX_RAM_SIZE - 1) 230#define CFG_BANK0_ENABLE 1 231#define CFG_BANK1_START 0x00000000 232#define CFG_BANK1_END 0x00000000 233#define CFG_BANK1_ENABLE 0 234#define CFG_BANK2_START 0x00000000 235#define CFG_BANK2_END 0x00000000 236#define CFG_BANK2_ENABLE 0 237#define CFG_BANK3_START 0x00000000 238#define CFG_BANK3_END 0x00000000 239#define CFG_BANK3_ENABLE 0 240#define CFG_BANK4_START 0x00000000 241#define CFG_BANK4_END 0x00000000 242#define CFG_BANK4_ENABLE 0 243#define CFG_BANK5_START 0x00000000 244#define CFG_BANK5_END 0x00000000 245#define CFG_BANK5_ENABLE 0 246#define CFG_BANK6_START 0x00000000 247#define CFG_BANK6_END 0x00000000 248#define CFG_BANK6_ENABLE 0 249#define CFG_BANK7_START 0x00000000 250#define CFG_BANK7_END 0x00000000 251#define CFG_BANK7_ENABLE 0 252 253/* 254 * Memory bank enable bitmask, specifying which of the banks defined above 255 * are actually present. MSB is for bank #7, LSB is for bank #0. 256 */ 257#define CFG_BANK_ENABLE 0x01 258 259#define CFG_ODCR 0xff /* configures line driver impedances, */ 260 /* see 8240 book for bit definitions */ 261#define CFG_PGMAX 0x32 /* how long the 8240 retains the */ 262 /* currently accessed page in memory */ 263 /* see 8240 book for details */ 264 265/* SDRAM 0 - 256MB */ 266#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) 267#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) 268 269#define CFG_IBAT1L (CFG_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE) 270#define CFG_IBAT1U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) 271 272/* PCI memory space */ 273#define CFG_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT) 274#define CFG_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) 275 276/* Config addrs, etc */ 277#define CFG_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT) 278#define CFG_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) 279 280#define CFG_DBAT0L CFG_IBAT0L 281#define CFG_DBAT0U CFG_IBAT0U 282#define CFG_DBAT1L CFG_IBAT1L 283#define CFG_DBAT1U CFG_IBAT1U 284#define CFG_DBAT2L CFG_IBAT2L 285#define CFG_DBAT2U CFG_IBAT2U 286#define CFG_DBAT3L CFG_IBAT3L 287#define CFG_DBAT3U CFG_IBAT3U 288 289/* 290 * For booting Linux, the board info and command line data 291 * have to be in the first 8 MB of memory, since this is 292 * the maximum mapped by the Linux kernel during initialization. 293 */ 294#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ 295 296/* 297 * Cache Configuration 298 */ 299#define CFG_CACHELINE_SIZE 32 /* For MPC8240 CPU */ 300#if defined(CONFIG_CMD_KGDB) 301# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ 302#endif 303 304 305/* 306 * Internal Definitions 307 * 308 * Boot Flags 309 */ 310#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ 311#define BOOTFLAG_WARM 0x02 /* Software reboot */ 312 313 314#endif /* __CONFIG_H */ 315