1/* 2 * (C) Copyright 2001 3 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. 4 * 5 * See file CREDITS for list of people who contributed to this 6 * project. 7 * 8 * This program is free software; you can redistribute it and/or 9 * modify it under the terms of the GNU General Public License as 10 * published by the Free Software Foundation; either version 2 of 11 * the License, or (at your option) any later version. 12 * 13 * This program is distributed in the hope that it will be useful, 14 * but WITHOUT ANY WARRANTY; without even the implied warranty of 15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 16 * GNU General Public License for more details. 17 * 18 * You should have received a copy of the GNU General Public License 19 * along with this program; if not, write to the Free Software 20 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 21 * MA 02111-1307 USA 22 */ 23 24 25#ifndef __CONFIG_H 26#define __CONFIG_H 27 28#define MV_VERSION "v0.2.0" 29 30/* LED0 = Power , LED1 = Error , LED2-5 = error code, LED6-7=00 -->PPCBoot error */ 31#define ERR_NONE 0 32#define ERR_ENV 1 33#define ERR_BOOTM_BADMAGIC 2 34#define ERR_BOOTM_BADCRC 3 35#define ERR_BOOTM_GUNZIP 4 36#define ERR_BOOTP_TIMEOUT 5 37#define ERR_DHCP 6 38#define ERR_TFTP 7 39#define ERR_NOLAN 8 40#define ERR_LANDRV 9 41 42#define CONFIG_BOARD_TYPES 1 43#define MVBLUE_BOARD_BOX 1 44#define MVBLUE_BOARD_LYNX 2 45 46#if 0 47#define ERR_LED(code) do { if (code) \ 48 *(volatile char *)(0xff000003) = ( 3 | (code<<4) ) & 0xf3; \ 49 else \ 50 *(volatile char *)(0xff000003) = ( 1 ); \ 51} while(0) 52#else 53#define ERR_LED(code) 54#endif 55 56#define CONFIG_MPC824X 1 57#define CONFIG_MPC8245 1 58#define CONFIG_MVBLUE 1 59 60#define CONFIG_CLOCKS_IN_MHZ 1 61 62#define CONFIG_BOARD_TYPES 1 63 64#define CONFIG_CONS_INDEX 1 65#define CONFIG_BAUDRATE 115200 66#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } 67 68#define CONFIG_BOOTDELAY 3 69#define CONFIG_BOOT_RETRY_TIME -1 70 71#define CONFIG_AUTOBOOT_KEYED 72#define CONFIG_AUTOBOOT_PROMPT \ 73 "autoboot in %d seconds (stop with 's')...\n", bootdelay 74#define CONFIG_AUTOBOOT_STOP_STR "s" 75#define CONFIG_ZERO_BOOTDELAY_CHECK 76#define CONFIG_RESET_TO_RETRY 60 77 78 79/* 80 * Command line configuration. 81 */ 82 83#define CONFIG_CMD_ASKENV 84#define CONFIG_CMD_BOOTD 85#define CONFIG_CMD_CACHE 86#define CONFIG_CMD_DHCP 87#define CONFIG_CMD_ECHO 88#define CONFIG_CMD_SAVEENV 89#define CONFIG_CMD_FLASH 90#define CONFIG_CMD_IMI 91#define CONFIG_CMD_IRQ 92#define CONFIG_CMD_NET 93#define CONFIG_CMD_PCI 94#define CONFIG_CMD_RUN 95 96 97/* 98 * BOOTP options 99 */ 100#define CONFIG_BOOTP_SUBNETMASK 101#define CONFIG_BOOTP_GATEWAY 102#define CONFIG_BOOTP_HOSTNAME 103#define CONFIG_BOOTP_BOOTPATH 104#define CONFIG_BOOTP_BOOTFILESIZE 105#define CONFIG_BOOTP_SUBNETMASK 106#define CONFIG_BOOTP_GATEWAY 107#define CONFIG_BOOTP_HOSTNAME 108#define CONFIG_BOOTP_NISDOMAIN 109#define CONFIG_BOOTP_BOOTPATH 110#define CONFIG_BOOTP_DNS 111#define CONFIG_BOOTP_DNS2 112#define CONFIG_BOOTP_SEND_HOSTNAME 113#define CONFIG_BOOTP_NTPSERVER 114#define CONFIG_BOOTP_TIMEOFFSET 115 116 117/* 118 * Miscellaneous configurable options 119 */ 120#define CONFIG_SYS_LONGHELP /* undef to save memory */ 121#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 122#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 123 124#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 125#define CONFIG_SYS_MAXARGS 16 /* Max number of command args */ 126#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 127#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* Default load address */ 128 129#define CONFIG_BOOTCOMMAND "run nfsboot" 130#define CONFIG_BOOTARGS "root=/dev/mtdblock5 ro rootfstype=jffs2" 131 132#define CONFIG_NFSBOOTCOMMAND "bootp; run nfsargs addcons;bootm" 133 134#define CONFIG_EXTRA_ENV_SETTINGS \ 135 "console_nr=0\0" \ 136 "dhcp_client_id=mvBOX-XP\0" \ 137 "dhcp_vendor-class-identifier=mvBOX\0" \ 138 "adminboot=setenv bootargs root=/dev/mtdblock5 rw rootfstype=jffs2;run addcons;bootm ffc00000\0" \ 139 "flashboot=setenv bootargs root=/dev/mtdblock5 ro rootfstype=jffs2;run addcons;bootm ffc00000\0" \ 140 "safeboot=setenv bootargs root=/dev/mtdblock2 rw rootfstype=cramfs;run addcons;bootm ffc00000\0" \ 141 "hdboot=setenv bootargs root=/dev/hda1;run addcons;bootm ffc00000\0" \ 142 "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ 143 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off\0" \ 144 "addcons=setenv bootargs ${bootargs} console=ttyS${console_nr},${baudrate}N8\0" \ 145 "mv_version=" MV_VERSION "\0" \ 146 "bootretry=30\0" 147 148#define CONFIG_OVERWRITE_ETHADDR_ONCE 149 150/*----------------------------------------------------------------------- 151 * PCI stuff 152 *----------------------------------------------------------------------- 153 */ 154 155#define CONFIG_PCI 156#define CONFIG_PCI_PNP 157#define CONFIG_PCI_SCAN_SHOW 158 159#define CONFIG_NET_MULTI 160#define CONFIG_NET_RETRY_COUNT 5 161 162#define CONFIG_TULIP 163#define CONFIG_TULIP_FIX_DAVICOM 1 164#define CONFIG_ETHADDR b6:b4:45:eb:fb:c0 165 166#define CONFIG_HW_WATCHDOG 167 168/*----------------------------------------------------------------------- 169 * Start addresses for the final memory configuration 170 * (Set up by the startup code) 171 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 172 */ 173#define CONFIG_SYS_SDRAM_BASE 0x00000000 174 175#define CONFIG_SYS_FLASH_BASE 0xFFF00000 176#define CONFIG_SYS_MONITOR_BASE TEXT_BASE 177 178#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100 179#define CONFIG_SYS_EUMB_ADDR 0xFC000000 180 181#define CONFIG_SYS_MONITOR_LEN 0x00100000 182#define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve some kB for malloc() */ 183 184#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ 185#define CONFIG_SYS_MEMTEST_END 0x00800000 /* 1M ... 8M in DRAM */ 186 187/* Maximum amount of RAM. */ 188#define CONFIG_SYS_MAX_RAM_SIZE 0x10000000 /* 0 .. 256MB of (S)DRAM */ 189 190 191#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE 192#undef CONFIG_SYS_RAMBOOT 193#else 194#define CONFIG_SYS_RAMBOOT 195#endif 196 197#define CONFIG_SYS_ISA_IO 0xFE000000 198 199/* 200 * serial configuration 201 */ 202#define CONFIG_SYS_NS16550 203#define CONFIG_SYS_NS16550_SERIAL 204 205#define CONFIG_SYS_NS16550_REG_SIZE 1 206 207#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 208 209#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_EUMB_ADDR + 0x4500) 210#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_EUMB_ADDR + 0x4600) 211 212/*----------------------------------------------------------------------- 213 * Definitions for initial stack pointer and data area 214 */ 215#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 216#define CONFIG_SYS_INIT_RAM_END 0x1000 217#define CONFIG_SYS_GBL_DATA_SIZE 128 218#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) 219 220/* 221 * Low Level Configuration Settings 222 * (address mappings, register initial values, etc.) 223 * You should know what you are doing if you make changes here. 224 * For the detail description refer to the MPC8240 user's manual. 225 */ 226 227#define CONFIG_SYS_CLK_FREQ 33000000 228#define CONFIG_SYS_HZ 10000 229 230/* Bit-field values for MCCR1. */ 231#define CONFIG_SYS_ROMNAL 7 232#define CONFIG_SYS_ROMFAL 11 233 234/* Bit-field values for MCCR2. */ 235#define CONFIG_SYS_TSWAIT 0x5 236#define CONFIG_SYS_REFINT 430 237 238/* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4. */ 239#define CONFIG_SYS_BSTOPRE 121 240 241/* Bit-field values for MCCR3. */ 242#define CONFIG_SYS_REFREC 8 243 244/* Bit-field values for MCCR4. */ 245#define CONFIG_SYS_PRETOACT 3 246#define CONFIG_SYS_ACTTOPRE 5 247#define CONFIG_SYS_ACTORW 3 248#define CONFIG_SYS_SDMODE_CAS_LAT 3 249#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1 250#define CONFIG_SYS_EXTROM 1 251#define CONFIG_SYS_REGDIMM 0 252#define CONFIG_SYS_DBUS_SIZE2 1 253#define CONFIG_SYS_SDMODE_WRAP 0 254 255#define CONFIG_SYS_PGMAX 0x32 256#define CONFIG_SYS_SDRAM_DSCD 0x20 257 258/* Memory bank settings. 259 * Only bits 20-29 are actually used from these vales to set the 260 * start/end addresses. The upper two bits will always be 0, and the lower 261 * 20 bits will be 0x00000 for a start address, or 0xfffff for an end 262 * address. Refer to the MPC8240 book. 263 */ 264 265#define CONFIG_SYS_BANK0_START 0x00000000 266#define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE - 1) 267#define CONFIG_SYS_BANK0_ENABLE 1 268#define CONFIG_SYS_BANK1_START 0x3ff00000 269#define CONFIG_SYS_BANK1_END 0x3fffffff 270#define CONFIG_SYS_BANK1_ENABLE 0 271#define CONFIG_SYS_BANK2_START 0x3ff00000 272#define CONFIG_SYS_BANK2_END 0x3fffffff 273#define CONFIG_SYS_BANK2_ENABLE 0 274#define CONFIG_SYS_BANK3_START 0x3ff00000 275#define CONFIG_SYS_BANK3_END 0x3fffffff 276#define CONFIG_SYS_BANK3_ENABLE 0 277#define CONFIG_SYS_BANK4_START 0x3ff00000 278#define CONFIG_SYS_BANK4_END 0x3fffffff 279#define CONFIG_SYS_BANK4_ENABLE 0 280#define CONFIG_SYS_BANK5_START 0x3ff00000 281#define CONFIG_SYS_BANK5_END 0x3fffffff 282#define CONFIG_SYS_BANK5_ENABLE 0 283#define CONFIG_SYS_BANK6_START 0x3ff00000 284#define CONFIG_SYS_BANK6_END 0x3fffffff 285#define CONFIG_SYS_BANK6_ENABLE 0 286#define CONFIG_SYS_BANK7_START 0x3ff00000 287#define CONFIG_SYS_BANK7_END 0x3fffffff 288#define CONFIG_SYS_BANK7_ENABLE 0 289 290#define CONFIG_SYS_ODCR 0xff 291 292#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) 293#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) 294 295#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE) 296#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) 297 298#define CONFIG_SYS_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT) 299#define CONFIG_SYS_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) 300 301#define CONFIG_SYS_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT) 302#define CONFIG_SYS_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) 303 304#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 305#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 306#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 307#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 308#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L 309#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 310#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L 311#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 312 313/* 314 * For booting Linux, the board info and command line data 315 * have to be in the first 8 MB of memory, since this is 316 * the maximum mapped by the Linux kernel during initialization. 317 */ 318#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ 319 320/*----------------------------------------------------------------------- 321 * FLASH organization 322 */ 323#undef CONFIG_SYS_FLASH_PROTECTION 324#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max number of flash banks */ 325#define CONFIG_SYS_MAX_FLASH_SECT 63 /* Max number of sectors per flash */ 326 327#define CONFIG_SYS_FLASH_ERASE_TOUT 12000 328#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 329 330 331#define CONFIG_ENV_IS_IN_FLASH 332 333#define CONFIG_ENV_OFFSET 0x00010000 334#define CONFIG_ENV_SIZE 0x00010000 335#define CONFIG_ENV_SECT_SIZE 0x00010000 336 337/*----------------------------------------------------------------------- 338 * Cache Configuration 339 */ 340#define CONFIG_SYS_CACHELINE_SIZE 32 341#if defined(CONFIG_CMD_KGDB) 342#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ 343#endif 344 345/* 346 * Internal Definitions 347 * 348 * Boot Flags 349 */ 350#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ 351#define BOOTFLAG_WARM 0x02 /* Software reboot */ 352 353#endif /* __CONFIG_H */ 354