1/* 2 * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net> 3 * 4 * This program is free software; you can redistribute it and/or 5 * modify it under the terms of the GNU General Public License as 6 * published by the Free Software Foundation; either version 2 of 7 * the License, or (at your option) any later version. 8 * 9 * This program is distributed in the hope that it will be useful, 10 * but WITHOUT ANY WARRANTY; without even the implied warranty of 11 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 12 * GNU General Public License for more details. 13 * 14 * You should have received a copy of the GNU General Public License 15 * along with this program; if not, write to the Free Software 16 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 17 * MA 02111-1307 USA 18 */ 19 20#ifndef __CONFIG_H 21#define __CONFIG_H 22 23/* 24 * Define this to make U-Boot skip low level initialization when loaded 25 * by initial bootloader. Not required by NAND U-Boot version but IS 26 * required for a NOR version used to burn the real NOR U-Boot into 27 * NOR Flash. NAND and NOR support for DaVinci chips is mutually exclusive 28 * so it is NOT possible to build a U-Boot with both NAND and NOR routines. 29 * NOR U-Boot is loaded directly from Flash so it must perform all the 30 * low level initialization itself. NAND version is loaded by an initial 31 * bootloader (UBL in TI-ese) that performs such an initialization so it's 32 * skipped in NAND version. The third DaVinci boot mode loads a bootloader 33 * via UART0 and that bootloader in turn loads and runs U-Boot (or whatever) 34 * performing low level init prior to loading. All that means we can NOT use 35 * NAND version to put U-Boot into NOR because it doesn't have NOR support and 36 * we can NOT use NOR version because it performs low level initialization 37 * effectively destroying itself in DDR memory. That's why a separate NOR 38 * version with this define is needed. It is loaded via UART, then one uses 39 * it to somehow download a proper NOR version built WITHOUT this define to 40 * RAM (tftp?) and burn it to NOR Flash. I would be probably able to squeeze 41 * NOR support into the initial bootloader so it won't be needed but DaVinci 42 * static RAM might be too small for this (I have something like 2Kbytes left 43 * as of now, without NOR support) so this might've not happened... 44 * 45#define CONFIG_NOR_UART_BOOT 46 */ 47 48/*=======*/ 49/* Board */ 50/*=======*/ 51#define DV_EVM 52#define CONFIG_SYS_NAND_SMALLPAGE 53#define CONFIG_SYS_USE_NOR 54#define CONFIG_DISPLAY_CPUINFO 55/*===================*/ 56/* SoC Configuration */ 57/*===================*/ 58#define CONFIG_ARM926EJS /* arm926ejs CPU core */ 59#define CONFIG_SYS_TIMERBASE 0x01c21400 /* use timer 0 */ 60#define CONFIG_SYS_HZ_CLOCK 27000000 /* Timer Input clock freq */ 61#define CONFIG_SYS_HZ 1000 62#define CONFIG_SOC_DM644X 63/*====================================================*/ 64/* EEPROM definitions for Atmel 24C256BN SEEPROM chip */ 65/* on Sonata/DV_EVM board. No EEPROM on schmoogie. */ 66/*====================================================*/ 67#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 68#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 69#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 70#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 71/*=============*/ 72/* Memory Info */ 73/*=============*/ 74#define CONFIG_SYS_MALLOC_LEN (0x10000 + 128*1024) /* malloc() len */ 75#define CONFIG_SYS_GBL_DATA_SIZE 128 /* reserved for initial data */ 76#define CONFIG_SYS_MEMTEST_START 0x80000000 /* memtest start address */ 77#define CONFIG_SYS_MEMTEST_END 0x81000000 /* 16MB RAM test */ 78#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ 79#define CONFIG_STACKSIZE (256*1024) /* regular stack */ 80#define PHYS_SDRAM_1 0x80000000 /* DDR Start */ 81#define PHYS_SDRAM_1_SIZE 0x10000000 /* DDR size 256MB */ 82#define DDR_8BANKS /* 8-bank DDR2 (256MB) */ 83/*====================*/ 84/* Serial Driver info */ 85/*====================*/ 86#define CONFIG_SYS_NS16550 87#define CONFIG_SYS_NS16550_SERIAL 88#define CONFIG_SYS_NS16550_REG_SIZE -4 /* NS16550 register size, byteorder */ 89#define CONFIG_SYS_NS16550_COM1 0x01c20000 /* Base address of UART0 */ 90#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_HZ_CLOCK /* Input clock to NS16550 */ 91#define CONFIG_CONS_INDEX 1 /* use UART0 for console */ 92#define CONFIG_BAUDRATE 115200 /* Default baud rate */ 93#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } 94/*===================*/ 95/* I2C Configuration */ 96/*===================*/ 97#define CONFIG_HARD_I2C 98#define CONFIG_DRIVER_DAVINCI_I2C 99#define CONFIG_SYS_I2C_SPEED 80000 /* 100Kbps won't work, silicon bug */ 100#define CONFIG_SYS_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */ 101/*==================================*/ 102/* Network & Ethernet Configuration */ 103/*==================================*/ 104#define CONFIG_DRIVER_TI_EMAC 105#define CONFIG_EMAC_MDIO_PHY_NUM 1 106#define CONFIG_MII 107#define CONFIG_BOOTP_DEFAULT 108#define CONFIG_BOOTP_DNS 109#define CONFIG_BOOTP_DNS2 110#define CONFIG_BOOTP_SEND_HOSTNAME 111#define CONFIG_NET_RETRY_COUNT 10 112#define CONFIG_NET_MULTI 113/*=====================*/ 114/* Flash & Environment */ 115/*=====================*/ 116#ifdef CONFIG_SYS_USE_NAND 117#define CONFIG_NAND_DAVINCI 118#define CONFIG_SYS_NAND_CS 2 119#undef CONFIG_ENV_IS_IN_FLASH 120#define CONFIG_SYS_NO_FLASH 121#define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */ 122#ifdef CONFIG_SYS_NAND_SMALLPAGE 123#define CONFIG_ENV_SECT_SIZE 512 /* Env sector Size */ 124#define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB */ 125#define CONFIG_MTD_PARTITIONS 126#define CONFIG_MTD_DEVICE 127#define CONFIG_CMD_MTDPARTS 128#define MTDIDS_DEFAULT \ 129 "nand0=davinci_nand.0" 130#define MTDPARTS_DEFAULT \ 131 "mtdparts=davinci_nand.0:384k(bootloader)ro,4m(kernel),-(filesystem)" 132#else 133#define CONFIG_ENV_SECT_SIZE 2048 /* Env sector Size */ 134#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */ 135#endif 136#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */ 137#define CONFIG_SKIP_RELOCATE_UBOOT /* to a proper address, init done */ 138#define CONFIG_SYS_NAND_BASE 0x02000000 139#define CONFIG_SYS_NAND_USE_FLASH_BBT 140#define CONFIG_SYS_NAND_HW_ECC 141#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ 142#define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */ 143#define DEF_BOOTM "" 144#elif defined(CONFIG_SYS_USE_NOR) 145#ifdef CONFIG_NOR_UART_BOOT 146#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */ 147#define CONFIG_SKIP_RELOCATE_UBOOT /* to a proper address, init done */ 148#else 149#undef CONFIG_SKIP_LOWLEVEL_INIT 150#undef CONFIG_SKIP_RELOCATE_UBOOT 151#endif 152#define CONFIG_ENV_IS_IN_FLASH 153#undef CONFIG_SYS_NO_FLASH 154#define CONFIG_FLASH_CFI_DRIVER 155#define CONFIG_SYS_FLASH_CFI 156#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of flash banks */ 157#define CONFIG_SYS_FLASH_SECT_SZ 0x10000 /* 64KB sect size AMD Flash */ 158#define CONFIG_ENV_OFFSET (CONFIG_SYS_FLASH_SECT_SZ*3) 159#define PHYS_FLASH_1 0x02000000 /* CS2 Base address */ 160#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 /* Flash Base for U-Boot */ 161#define PHYS_FLASH_SIZE 0x2000000 /* Flash size 32MB */ 162#define CONFIG_SYS_MAX_FLASH_SECT (PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ) 163#define CONFIG_ENV_SECT_SIZE CONFIG_SYS_FLASH_SECT_SZ /* Env sector Size */ 164#endif 165/*==============================*/ 166/* U-Boot general configuration */ 167/*==============================*/ 168#undef CONFIG_USE_IRQ /* No IRQ/FIQ in U-Boot */ 169#define CONFIG_MISC_INIT_R 170#undef CONFIG_BOOTDELAY 171#define CONFIG_BOOTFILE "uImage" /* Boot file name */ 172#define CONFIG_SYS_PROMPT "U-Boot > " /* Monitor Command Prompt */ 173#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 174#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print buffer sz */ 175#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 176#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 177#define CONFIG_SYS_LOAD_ADDR 0x80700000 /* default Linux kernel load address */ 178#define CONFIG_VERSION_VARIABLE 179#define CONFIG_AUTO_COMPLETE /* Won't work with hush so far, may be later */ 180#define CONFIG_SYS_HUSH_PARSER 181#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 182#define CONFIG_CMDLINE_EDITING 183#define CONFIG_SYS_LONGHELP 184#define CONFIG_CRC32_VERIFY 185#define CONFIG_MX_CYCLIC 186#define CONFIG_MUSB_HCD 187#define CONFIG_USB_DAVINCI 188/*===================*/ 189/* Linux Information */ 190/*===================*/ 191#define LINUX_BOOT_PARAM_ADDR 0x80000100 192#define CONFIG_CMDLINE_TAG 193#define CONFIG_SETUP_MEMORY_TAGS 194#define CONFIG_BOOTARGS "mem=120M console=ttyS0,115200n8 root=/dev/hda1 rw noinitrd ip=dhcp" 195#define CONFIG_BOOTCOMMAND "setenv setboot setenv bootargs \\$(bootargs) video=dm64xxfb:output=\\$(videostd);run setboot; bootm 0x2050000" 196/*=================*/ 197/* U-Boot commands */ 198/*=================*/ 199#include <config_cmd_default.h> 200#define CONFIG_CMD_ASKENV 201#define CONFIG_CMD_DHCP 202#define CONFIG_CMD_DIAG 203#define CONFIG_CMD_I2C 204#define CONFIG_CMD_MII 205#define CONFIG_CMD_PING 206#define CONFIG_CMD_SAVES 207#define CONFIG_CMD_EEPROM 208#undef CONFIG_CMD_BDI 209#undef CONFIG_CMD_FPGA 210#undef CONFIG_CMD_SETGETDCR 211#ifdef CONFIG_SYS_USE_NAND 212#undef CONFIG_CMD_FLASH 213#undef CONFIG_CMD_IMLS 214#define CONFIG_CMD_NAND 215#elif defined(CONFIG_SYS_USE_NOR) 216#define CONFIG_CMD_JFFS2 217#else 218#error "Either CONFIG_SYS_USE_NAND or CONFIG_SYS_USE_NOR _MUST_ be defined !!!" 219#endif 220/*==========================*/ 221/* USB MSC support (if any) */ 222/*==========================*/ 223#ifdef CONFIG_USB_DAVINCI 224#define CONFIG_CMD_USB 225#ifdef CONFIG_MUSB_HCD 226#define CONFIG_USB_STORAGE 227#define CONFIG_CMD_STORAGE 228#define CONFIG_CMD_FAT 229#define CONFIG_DOS_PARTITION 230#endif 231#ifdef CONFIG_USB_KEYBOARD 232#define CONFIG_SYS_USB_EVENT_POLL 233#define CONFIG_PREBOOT "usb start" 234#endif 235#endif 236/*=======================*/ 237/* KGDB support (if any) */ 238/*=======================*/ 239#ifdef CONFIG_CMD_KGDB 240#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */ 241#define CONFIG_KGDB_SER_INDEX 1 /* which serial port to use */ 242#endif 243#endif /* __CONFIG_H */ 244