1/* 2 * (C) Copyright 2001 3 * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com 4 * 5 * See file CREDITS for list of people who contributed to this 6 * project. 7 * 8 * This program is free software; you can redistribute it and/or 9 * modify it under the terms of the GNU General Public License as 10 * published by the Free Software Foundation; either version 2 of 11 * the License, or (at your option) any later version. 12 * 13 * This program is distributed in the hope that it will be useful, 14 * but WITHOUT ANY WARRANTY; without even the implied warranty of 15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 16 * GNU General Public License for more details. 17 * 18 * You should have received a copy of the GNU General Public License 19 * along with this program; if not, write to the Free Software 20 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 21 * MA 02111-1307 USA 22 */ 23 24/* 25 * board/config.h - configuration options, board specific 26 */ 27 28#ifndef __CONFIG_H 29#define __CONFIG_H 30 31/* 32 * High Level Configuration Options 33 * (easy to change) 34 */ 35 36#define CONFIG_405GP 1 /* This is a PPC405 CPU */ 37#define CONFIG_4xx 1 /* ...member of PPC4xx family */ 38#define CONFIG_ORSG 1 /* ...on a ORSG board */ 39 40#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ 41 42#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */ 43 44#define CONFIG_BAUDRATE 9600 45#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ 46 47#undef CONFIG_BOOTARGS 48#define CONFIG_BOOTCOMMAND "go fff00100" 49 50#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 51#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 52 53#define CONFIG_PPC4xx_EMAC 54#define CONFIG_MII 1 /* MII PHY management */ 55#define CONFIG_PHY_ADDR 0 /* PHY address */ 56#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */ 57 58 59/* 60 * BOOTP options 61 */ 62#define CONFIG_BOOTP_BOOTFILESIZE 63#define CONFIG_BOOTP_BOOTPATH 64#define CONFIG_BOOTP_GATEWAY 65#define CONFIG_BOOTP_HOSTNAME 66 67 68/* 69 * Command line configuration. 70 */ 71#include <config_cmd_default.h> 72 73#define CONFIG_CMD_PCI 74#define CONFIG_CMD_IRQ 75#define CONFIG_CMD_ASKENV 76#define CONFIG_CMD_ELF 77#define CONFIG_CMD_BSP 78#define CONFIG_CMD_EEPROM 79 80 81#define CONFIG_MAC_PARTITION 82#define CONFIG_DOS_PARTITION 83 84#undef CONFIG_WATCHDOG /* watchdog disabled */ 85 86#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ 87 88/* 89 * Miscellaneous configurable options 90 */ 91#define CONFIG_SYS_LONGHELP /* undef to save memory */ 92#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 93#if defined(CONFIG_CMD_KGDB) 94#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 95#else 96#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 97#endif 98#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 99#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 100#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 101 102#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ 103 104#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ 105#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ 106 107#define CONFIG_CONS_INDEX 1 /* Use UART0 */ 108#define CONFIG_SYS_NS16550 109#define CONFIG_SYS_NS16550_SERIAL 110#define CONFIG_SYS_NS16550_REG_SIZE 1 111#define CONFIG_SYS_NS16550_CLK get_serial_clock() 112 113#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ 114#define CONFIG_SYS_BASE_BAUD 691200 115 116/* The following table includes the supported baudrates */ 117#define CONFIG_SYS_BAUDRATE_TABLE \ 118 { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ 119 57600, 115200, 230400, 460800, 921600 } 120 121#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ 122#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ 123 124#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ 125 126#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ 127 128/*----------------------------------------------------------------------- 129 * PCI stuff 130 *----------------------------------------------------------------------- 131 */ 132#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ 133#define PCI_HOST_FORCE 1 /* configure as pci host */ 134#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ 135 136#define CONFIG_PCI /* include pci support */ 137#define CONFIG_PCI_HOST PCI_HOST_ADAPTER /* select pci adapter */ 138#undef CONFIG_PCI_PNP /* no pci plug-and-play */ 139 /* resource configuration */ 140 141#undef CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ 142 143#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ 144#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0411 /* PCI Device ID: ORSG */ 145#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ 146#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ 147#define CONFIG_SYS_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */ 148#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ 149#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */ 150#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ 151#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ 152 153/*----------------------------------------------------------------------- 154 * Start addresses for the final memory configuration 155 * (Set up by the startup code) 156 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 157 */ 158#define CONFIG_SYS_SDRAM_BASE 0x00000000 159#define CONFIG_SYS_FLASH_BASE 0xFFFD0000 160#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE 161#define CONFIG_SYS_MONITOR_LEN (192 * 1024) /* Reserve 192 kB for Monitor */ 162#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ 163 164/* 165 * For booting Linux, the board info and command line data 166 * have to be in the first 8 MB of memory, since this is 167 * the maximum mapped by the Linux kernel during initialization. 168 */ 169#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ 170/*----------------------------------------------------------------------- 171 * FLASH organization 172 */ 173#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ 174#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ 175 176#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ 177#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ 178 179#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */ 180#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */ 181#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */ 182/* 183 * The following defines are added for buggy IOP480 byte interface. 184 * All other boards should use the standard values (CPCI405 etc.) 185 */ 186#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */ 187#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */ 188#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */ 189 190#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ 191 192#if 0 /* Use NVRAM for environment variables */ 193/*----------------------------------------------------------------------- 194 * NVRAM organization 195 */ 196#define CONFIG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */ 197#define CONFIG_SYS_NVRAM_BASE_ADDR 0xf0200000 /* NVRAM base address */ 198#define CONFIG_SYS_NVRAM_SIZE (32*1024) /* NVRAM size */ 199#define CONFIG_ENV_SIZE 0x1000 /* Size of Environment vars */ 200#define CONFIG_ENV_ADDR \ 201 (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) /* Env */ 202#define CONFIG_SYS_NVRAM_VXWORKS_OFFS 0x6900 /* Offset for VxWorks eth-addr */ 203 204#else /* Use EEPROM for environment variables */ 205 206#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ 207#define CONFIG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */ 208#define CONFIG_ENV_SIZE 0x300 /* 768 bytes may be used for env vars */ 209 /* total size of a CAT24WC08 is 1024 bytes */ 210#endif 211 212/*----------------------------------------------------------------------- 213 * I2C EEPROM (CAT24WC08) for environment 214 */ 215#define CONFIG_HARD_I2C /* I2c with hardware support */ 216#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ 217#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ 218#define CONFIG_SYS_I2C_SLAVE 0x7F 219 220#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ 221#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ 222/* mask of address bits that overflow into the "EEPROM chip address" */ 223#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 224#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */ 225 /* 16 byte page write mode using*/ 226 /* last 4 bits of the address */ 227#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ 228 229/* 230 * Init Memory Controller: 231 * 232 * BR0/1 and OR0/1 (FLASH) 233 */ 234 235#define FLASH_BASE0_PRELIM 0xFF800000 /* FLASH bank #0 */ 236#define FLASH_BASE1_PRELIM 0xFFC00000 /* FLASH bank #1 */ 237 238/*----------------------------------------------------------------------- 239 * External Bus Controller (EBC) Setup 240 */ 241 242/* Memory Bank 0 (Flash Bank 0) initialization */ 243#define CONFIG_SYS_EBC_PB0AP 0x92015480 244#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */ 245 246/* Memory Bank 1 (Flash Bank 1) initialization */ 247#define CONFIG_SYS_EBC_PB1AP 0x92015480 248#define CONFIG_SYS_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */ 249 250/* Memory Bank 2 (PLD - FPGA-boot) initialization */ 251#define CONFIG_SYS_EBC_PB2AP 0x02015480 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */ 252 /* WBN=0x1,WBF=0x1,TH=0x2,RE=0x0,SOR=0x1,BEM=0x0,PEN=0x0*/ 253#define CONFIG_SYS_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ 254 255/* Memory Bank 3 (PLD - OSL) initialization */ 256#define CONFIG_SYS_EBC_PB3AP 0x02015480 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */ 257 /* WBN=0x1,WBF=0x1,TH=0x2,RE=0x0,SOR=0x1,BEM=0x0,PEN=0x0*/ 258#define CONFIG_SYS_EBC_PB3CR 0xF0118000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=8bit */ 259 260/* Memory Bank 4 (Spartan2 1) initialization */ 261#define CONFIG_SYS_EBC_PB4AP 0x02015580 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */ 262 /* WBN=0x1,WBF=0x1,TH=0x2,RE=0x1,SOR=0x1,BEM=0x0,PEN=0x0*/ 263#define CONFIG_SYS_EBC_PB4CR 0xF209C000 /* BAS=0xF20,BS=16MB,BU=R/W,BW=32bit*/ 264 265/* Memory Bank 5 (Spartan2 2) initialization */ 266#define CONFIG_SYS_EBC_PB5AP 0x02015580 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */ 267 /* WBN=0x1,WBF=0x1,TH=0x2,RE=0x1,SOR=0x1,BEM=0x0,PEN=0x0*/ 268#define CONFIG_SYS_EBC_PB5CR 0xF309C000 /* BAS=0xF30,BS=16MB,BU=R/W,BW=32bit*/ 269 270/* Memory Bank 6 (Virtex 1) initialization */ 271#define CONFIG_SYS_EBC_PB6AP 0x02015580 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */ 272 /* WBN=0x1,WBF=0x1,TH=0x2,RE=0x1,SOR=0x1,BEM=0x0,PEN=0x0*/ 273#define CONFIG_SYS_EBC_PB6CR 0xF409A000 /* BAS=0xF40,BS=16MB,BU=R/W,BW=16bit*/ 274 275/* Memory Bank 7 (Virtex 2) initialization */ 276#define CONFIG_SYS_EBC_PB7AP 0x02015580 /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */ 277 /* WBN=0x1,WBF=0x1,TH=0x2,RE=0x1,SOR=0x1,BEM=0x0,PEN=0x0*/ 278#define CONFIG_SYS_EBC_PB7CR 0xF509A000 /* BAS=0xF50,BS=16MB,BU=R/W,BW=16bit*/ 279 280 281#define CONFIG_SYS_VXWORKS_MAC_PTR 0x00000000 /* Pass Ethernet MAC to VxWorks */ 282 283/*----------------------------------------------------------------------- 284 * Definitions for initial stack pointer and data area (in DPRAM) 285 */ 286 287/* use on chip memory ( OCM ) for temperary stack until sdram is tested */ 288#define CONFIG_SYS_TEMP_STACK_OCM 1 289 290/* On Chip Memory location */ 291#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 292#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 293 294#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ 295#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ 296#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 297#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 298 299#endif /* __CONFIG_H */ 300