/*
 * Copyright (C) 2006 Freescale Semiconductor, Inc.
 *                    Dave Liu <daveliu@freescale.com>
 *
 * Copyright (C) 2007 Logic Product Development, Inc.
 *                    Peter Barada <peterb@logicpd.com>
 *
 * Copyright (C) 2007 MontaVista Software, Inc.
 *                    Anton Vorontsov <avorontsov@ru.mvista.com>
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * High Level Configuration Options
 */
#define CONFIG_E300             1 /* E300 family */
#define CONFIG_QE               1 /* Has QE */
#define CONFIG_MPC83xx          1 /* MPC83xx family */
#define CONFIG_MPC8360          1 /* MPC8360 CPU specific */
#define CONFIG_MPC8360ERDK      1 /* MPC8360ERDK board specific */

#define CONFIG_SYS_TEXT_BASE    0xFF800000

/*
 * System Clock Setup
 */
#ifdef CONFIG_CLKIN_33MHZ
#define CONFIG_83XX_CLKIN               33333333
#define CONFIG_SYS_CLK_FREQ             33333333
#define CONFIG_PCI_33M                          1
#define HRCWL_CSB_TO_CLKIN_MPC8360ERDK  HRCWL_CSB_TO_CLKIN_10X1
#else
#define CONFIG_83XX_CLKIN               66000000
#define CONFIG_SYS_CLK_FREQ             66000000
#define CONFIG_PCI_66M                          1
#define HRCWL_CSB_TO_CLKIN_MPC8360ERDK  HRCWL_CSB_TO_CLKIN_5X1
#endif /* CONFIG_CLKIN_33MHZ */

/*
 * Hardware Reset Configuration Word
 */
#define CONFIG_SYS_HRCW_LOW (\
        HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
        HRCWL_DDR_TO_SCB_CLK_1X1 |\
        HRCWL_CSB_TO_CLKIN_MPC8360ERDK |\
        HRCWL_CORE_TO_CSB_2X1 |\
        HRCWL_CE_TO_PLL_1X15)

#define CONFIG_SYS_HRCW_HIGH (\
        HRCWH_PCI_HOST |\
        HRCWH_PCI1_ARBITER_ENABLE |\
        HRCWH_PCICKDRV_ENABLE |\
        HRCWH_CORE_ENABLE |\
        HRCWH_FROM_0X00000100 |\
        HRCWH_BOOTSEQ_DISABLE |\
        HRCWH_SW_WATCHDOG_DISABLE |\
        HRCWH_ROM_LOC_LOCAL_16BIT |\
        HRCWH_SECONDARY_DDR_DISABLE |\
        HRCWH_BIG_ENDIAN |\
        HRCWH_LALE_EARLY)

/*
 * System IO Config
 */
#define CONFIG_SYS_SICRH                0x00000000
#define CONFIG_SYS_SICRL                0x40000000

#define CONFIG_BOARD_EARLY_INIT_R

/*
 * IMMR new address
 */
#define CONFIG_SYS_IMMR         0xE0000000

/*
 * DDR Setup
 */
#define CONFIG_SYS_DDR_BASE             0x00000000 /* DDR is system memory */
#define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE       CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   (DDR_SDRAM_CLK_CNTL_SS_EN \
                                        | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)

#define CONFIG_SYS_83XX_DDR_USES_CS0

#define CONFIG_DDR_ECC          /* support DDR ECC function */
#define CONFIG_DDR_ECC_CMD      /* Use DDR ECC user commands */

/*
 * DDRCDR - DDR Control Driver Register
 */
#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_DHC_EN \
                                | DDRCDR_ODT \
                                | DDRCDR_Q_DRN)
                                /* 0x80080001 */

#undef CONFIG_SPD_EEPROM        /* Do not use SPD EEPROM for DDR setup */

/*
 * Manually set up DDR parameters
 */
#define CONFIG_DDR_II
#define CONFIG_SYS_DDR_SIZE             256 /* MB */
#define CONFIG_SYS_DDR_CS0_BNDS         0x0000000f
#define CONFIG_SYS_DDR_CS0_CONFIG       (CSCONFIG_EN \
                                        | CSCONFIG_ROW_BIT_13 \
                                        | CSCONFIG_COL_BIT_10 \
                                        | CSCONFIG_ODT_WR_ONLY_CURRENT)
#define CONFIG_SYS_DDR_SDRAM_CFG        (SDRAM_CFG_SDRAM_TYPE_DDR2 \
                                        | SDRAM_CFG_ECC_EN)
#define CONFIG_SYS_DDR_SDRAM_CFG2       0x00001000
#define CONFIG_SYS_DDR_CLK_CNTL         (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
#define CONFIG_SYS_DDR_INTERVAL         ((256 << SDRAM_INTERVAL_BSTOPRE_SHIFT) \
                                        | (1115 << SDRAM_INTERVAL_REFINT_SHIFT))
#define CONFIG_SYS_DDR_MODE             0x47800432
#define CONFIG_SYS_DDR_MODE2            0x8000c000

#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
                                 (9 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
                                 (3 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
                                 (3 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
                                 (0 << TIMING_CFG0_WWT_SHIFT) | \
                                 (0 << TIMING_CFG0_RRT_SHIFT) | \
                                 (0 << TIMING_CFG0_WRT_SHIFT) | \
                                 (0 << TIMING_CFG0_RWT_SHIFT))

#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_30) | \
                                 (2 << TIMING_CFG1_WRTORD_SHIFT) | \
                                 (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
                                 (3 << TIMING_CFG1_WRREC_SHIFT) | \
                                 (10 << TIMING_CFG1_REFREC_SHIFT) | \
                                 (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
                                 (8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
                                 (3 << TIMING_CFG1_PRETOACT_SHIFT))

#define CONFIG_SYS_DDR_TIMING_2 ((9 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
                                 (4 << TIMING_CFG2_CKE_PLS_SHIFT) | \
                                 (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
                                 (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
                                 (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
                                 (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
                                 (0 << TIMING_CFG2_CPO_SHIFT))

#define CONFIG_SYS_DDR_TIMING_3 0x00000000

/*
 * Memory test
 */
#undef CONFIG_SYS_DRAM_TEST             /* memory test, takes time */
#define CONFIG_SYS_MEMTEST_START        0x00000000 /* memtest region */
#define CONFIG_SYS_MEMTEST_END          0x00100000

/*
 * The reserved memory
 */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#define CONFIG_SYS_FLASH_BASE           0xFF800000 /* FLASH base address */

#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
#define CONFIG_SYS_RAMBOOT
#else
#undef  CONFIG_SYS_RAMBOOT
#endif

#define CONFIG_SYS_MONITOR_LEN  (384 * 1024) /* Reserve 384 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN   (128 * 1024) /* Reserved for malloc */

/*
 * Initial RAM Base Address Setup
 */
#define CONFIG_SYS_INIT_RAM_LOCK        1
#define CONFIG_SYS_INIT_RAM_ADDR        0xE6000000 /* Initial RAM address */
#define CONFIG_SYS_INIT_RAM_SIZE        0x1000 /* Size of used area in RAM */
#define CONFIG_SYS_GBL_DATA_OFFSET      \
                        (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)

/*
 * Local Bus Configuration & Clock Setup
 */
#define CONFIG_SYS_LCRR_DBYP    LCRR_DBYP
#define CONFIG_SYS_LCRR_CLKDIV  LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR     0x00000000

/*
 * FLASH on the Local Bus
 */
#define CONFIG_SYS_FLASH_CFI            /* use the Common Flash Interface */
#define CONFIG_FLASH_CFI_DRIVER         /* use the CFI driver */
#define CONFIG_SYS_FLASH_SIZE           8 /* max FLASH size is 32M */
#define CONFIG_SYS_FLASH_PROTECTION     1 /* Use intel Flash protection. */

                                        /* Window base at flash base */
#define CONFIG_SYS_LBLAWBAR0_PRELIM     CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_LBLAWAR0_PRELIM      (LBLAWAR_EN | LBLAWAR_32MB)

#define CONFIG_SYS_BR0_PRELIM   (CONFIG_SYS_FLASH_BASE \
                                | BR_PS_16      /* 16 bit port */ \
                                | BR_MS_GPCM    /* MSEL = GPCM */ \
                                | BR_V)         /* valid */
#define CONFIG_SYS_OR0_PRELIM   (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
                                | OR_UPM_XAM \
                                | OR_GPCM_CSNT \
                                | OR_GPCM_ACS_DIV2 \
                                | OR_GPCM_XACS \
                                | OR_GPCM_SCY_15 \
                                | OR_GPCM_TRLX_SET \
                                | OR_GPCM_EHTR_SET \
                                | OR_GPCM_EAD)

#define CONFIG_SYS_MAX_FLASH_BANKS      1 /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT       256 /* max sectors per device */

#undef  CONFIG_SYS_FLASH_CHECKSUM

/*
 * NAND flash on the local bus
 */
#define CONFIG_SYS_NAND_BASE            0x60000000
#define CONFIG_CMD_NAND         1
#define CONFIG_NAND_FSL_UPM     1
#define CONFIG_SYS_MAX_NAND_DEVICE      1
#define CONFIG_MTD_NAND_VERIFY_WRITE

#define CONFIG_SYS_LBLAWBAR1_PRELIM     CONFIG_SYS_NAND_BASE
/*
 * [RFC] Comment said 4KB window; code said 256MB window; OR1 says 64MB
 * ... What's correct?
 */
#define CONFIG_SYS_LBLAWAR1_PRELIM      (LBLAWAR_EN | LBLAWAR_256MB)

/* Port size 8 bit, UPMA */
#define CONFIG_SYS_BR1_PRELIM           (CONFIG_SYS_NAND_BASE \
                                        | BR_PS_8 \
                                        | BR_MS_UPMA \
                                        | BR_V)
                                        /* 0x60000881 */
#define CONFIG_SYS_OR1_PRELIM           (OR_AM_64MB | OR_UPM_EAD)
                                        /* 0xFC000001 */

/*
 * Fujitsu MB86277 (MINT) graphics controller
 */
#define CONFIG_SYS_VIDEO_BASE           0x70000000

#define CONFIG_SYS_LBLAWBAR2_PRELIM     CONFIG_SYS_VIDEO_BASE
#define CONFIG_SYS_LBLAWAR2_PRELIM      (LBLAWAR_EN | LBLAWAR_64MB)

/* Port size 32 bit, UPMB */
#define CONFIG_SYS_BR2_PRELIM   (CONFIG_SYS_VIDEO_BASE \
                                | BR_PS_32 \
                                | BR_MS_UPMB \
                                | BR_V)
                                /* 0x000018a1 */
#define CONFIG_SYS_OR2_PRELIM   (OR_AM_64MB | OR_UPM_EAD)
                                /* 0xFC000001 */

/*
 * Serial Port
 */
#define CONFIG_CONS_INDEX       1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE     1
#define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)

#define CONFIG_SYS_BAUDRATE_TABLE  \
                {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}

#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)

#define CONFIG_CMDLINE_EDITING  1       /* add command line history */
#define CONFIG_AUTO_COMPLETE            /* add autocompletion support */
/* Use the HUSH parser */
#define CONFIG_SYS_HUSH_PARSER
#ifdef  CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif

/* Pass open firmware flat tree */
#define CONFIG_OF_LIBFDT        1
#define CONFIG_OF_BOARD_SETUP   1
#define CONFIG_OF_STDOUT_VIA_ALIAS

/* I2C */
#define CONFIG_HARD_I2C         /* I2C with hardware support */
#undef  CONFIG_SOFT_I2C         /* I2C bit-banged */
#define CONFIG_FSL_I2C
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_SYS_I2C_SPEED    400000  /* I2C speed and slave address */
#define CONFIG_SYS_I2C_SLAVE    0x7F
#define CONFIG_SYS_I2C_NOPROBES { {0, 0x52} } /* Don't probe these addrs */
#define CONFIG_SYS_I2C_OFFSET   0x3000
#define CONFIG_SYS_I2C2_OFFSET  0x3100

/*
 * General PCI
 * Addresses are mapped 1-1.
 */
#define CONFIG_PCI

#define CONFIG_SYS_PCI1_MEM_BASE        0x80000000
#define CONFIG_SYS_PCI1_MEM_PHYS        CONFIG_SYS_PCI1_MEM_BASE
#define CONFIG_SYS_PCI1_MEM_SIZE        0x10000000 /* 256M */
#define CONFIG_SYS_PCI1_MMIO_BASE       0x90000000
#define CONFIG_SYS_PCI1_MMIO_PHYS       CONFIG_SYS_PCI1_MMIO_BASE
#define CONFIG_SYS_PCI1_MMIO_SIZE       0x10000000 /* 256M */
#define CONFIG_SYS_PCI1_IO_BASE         0xE0300000
#define CONFIG_SYS_PCI1_IO_PHYS         0xE0300000
#define CONFIG_SYS_PCI1_IO_SIZE         0x100000 /* 1M */

#ifdef CONFIG_PCI

#define CONFIG_PCI_PNP          /* do pci plug-and-play */

#undef CONFIG_EEPRO100
#undef CONFIG_PCI_SCAN_SHOW     /* show pci devices on startup */
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957   /* Freescale */

#endif  /* CONFIG_PCI */

/*
 * QE UEC ethernet configuration
 */
#define CONFIG_UEC_ETH
#define CONFIG_ETHPRIME         "UEC0"

#define CONFIG_UEC_ETH1         /* GETH1 */

#ifdef CONFIG_UEC_ETH1
#define CONFIG_SYS_UEC1_UCC_NUM 0       /* UCC1 */
#define CONFIG_SYS_UEC1_RX_CLK          QE_CLK_NONE
#define CONFIG_SYS_UEC1_TX_CLK          QE_CLK9
#define CONFIG_SYS_UEC1_ETH_TYPE        GIGA_ETH
#define CONFIG_SYS_UEC1_PHY_ADDR        2
#define CONFIG_SYS_UEC1_INTERFACE_TYPE  PHY_INTERFACE_MODE_RGMII_RXID
#define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000
#endif

#define CONFIG_UEC_ETH2         /* GETH2 */

#ifdef CONFIG_UEC_ETH2
#define CONFIG_SYS_UEC2_UCC_NUM 1       /* UCC2 */
#define CONFIG_SYS_UEC2_RX_CLK          QE_CLK_NONE
#define CONFIG_SYS_UEC2_TX_CLK          QE_CLK4
#define CONFIG_SYS_UEC2_ETH_TYPE        GIGA_ETH
#define CONFIG_SYS_UEC2_PHY_ADDR        4
#define CONFIG_SYS_UEC2_INTERFACE_TYPE  PHY_INTERFACE_MODE_RGMII_RXID
#define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000
#endif

/*
 * Environment
 */

#ifndef CONFIG_SYS_RAMBOOT
#define CONFIG_ENV_IS_IN_FLASH  1
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
#define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K(one sector) for env */
#define CONFIG_ENV_SIZE         0x20000
#else /* CONFIG_SYS_RAMBOOT */
#define CONFIG_SYS_NO_FLASH     1       /* Flash is not usable now */
#define CONFIG_ENV_IS_NOWHERE   1       /* Store ENV in memory only */
#define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
#define CONFIG_ENV_SIZE         0x2000
#endif /* CONFIG_SYS_RAMBOOT */

#define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */

/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME


/*
 * Command line configuration.
 */
#include <config_cmd_default.h>

#define CONFIG_CMD_PING
#define CONFIG_CMD_I2C
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DHCP

#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
#endif

#if defined(CONFIG_SYS_RAMBOOT)
#undef CONFIG_CMD_SAVEENV
#undef CONFIG_CMD_LOADS
#endif

#undef CONFIG_WATCHDOG          /* watchdog disabled */

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP             /* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR            0x2000000 /* default load address */
#define CONFIG_SYS_PROMPT               "=> "   /* Monitor Command Prompt */

#if defined(CONFIG_CMD_KGDB)
        #define CONFIG_SYS_CBSIZE       1024 /* Console I/O Buffer Size */
#else
        #define CONFIG_SYS_CBSIZE       256 /* Console I/O Buffer Size */
#endif

                                /* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS      16      /* max number of command args */
                                /* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
#define CONFIG_SYS_HZ           1000    /* decrementer freq: 1ms ticks */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 256 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ    (256 << 20) /* Initial Memory map for Linux */

/*
 * Core HID Setup
 */
#define CONFIG_SYS_HID0_INIT    0x000000000
#define CONFIG_SYS_HID0_FINAL   (HID0_ENABLE_MACHINE_CHECK | \
                                 HID0_ENABLE_INSTRUCTION_CACHE)
#define CONFIG_SYS_HID2         HID2_HBE

/*
 * MMU Setup
 */

#define CONFIG_HIGH_BATS        1       /* High BATs supported */

/* DDR: cache cacheable */
#define CONFIG_SYS_IBAT0L       (CONFIG_SYS_SDRAM_BASE \
                                | BATL_PP_RW \
                                | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT0U       (CONFIG_SYS_SDRAM_BASE \
                                | BATU_BL_256M \
                                | BATU_VS \
                                | BATU_VP)
#define CONFIG_SYS_DBAT0L       CONFIG_SYS_IBAT0L
#define CONFIG_SYS_DBAT0U       CONFIG_SYS_IBAT0U

/* IMMRBAR & PCI IO: cache-inhibit and guarded */
#define CONFIG_SYS_IBAT1L       (CONFIG_SYS_IMMR \
                                | BATL_PP_RW \
                                | BATL_CACHEINHIBIT \
                                | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT1U       (CONFIG_SYS_IMMR \
                                | BATU_BL_4M \
                                | BATU_VS \
                                | BATU_VP)
#define CONFIG_SYS_DBAT1L       CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U       CONFIG_SYS_IBAT1U

/* NAND: cache-inhibit and guarded */
#define CONFIG_SYS_IBAT2L       (CONFIG_SYS_NAND_BASE \
                                | BATL_PP_RW \
                                | BATL_CACHEINHIBIT \
                                | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT2U       (CONFIG_SYS_NAND_BASE \
                                | BATU_BL_64M \
                                | BATU_VS \
                                | BATU_VP)
#define CONFIG_SYS_DBAT2L       CONFIG_SYS_IBAT2L
#define CONFIG_SYS_DBAT2U       CONFIG_SYS_IBAT2U

/* FLASH: icache cacheable, but dcache-inhibit and guarded */
#define CONFIG_SYS_IBAT3L       (CONFIG_SYS_FLASH_BASE \
                                | BATL_PP_RW \
                                | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT3U       (CONFIG_SYS_FLASH_BASE \
                                | BATU_BL_32M \
                                | BATU_VS \
                                | BATU_VP)
#define CONFIG_SYS_DBAT3L       (CONFIG_SYS_FLASH_BASE \
                                | BATL_PP_RW \
                                | BATL_CACHEINHIBIT \
                                | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT3U       CONFIG_SYS_IBAT3U

/* Stack in dcache: cacheable, no memory coherence */
#define CONFIG_SYS_IBAT4L       (CONFIG_SYS_INIT_RAM_ADDR \
                                | BATL_PP_RW)
#define CONFIG_SYS_IBAT4U       (CONFIG_SYS_INIT_RAM_ADDR \
                                | BATU_BL_128K \
                                | BATU_VS \
                                | BATU_VP)
#define CONFIG_SYS_DBAT4L       CONFIG_SYS_IBAT4L
#define CONFIG_SYS_DBAT4U       CONFIG_SYS_IBAT4U

#define CONFIG_SYS_IBAT5L       (CONFIG_SYS_VIDEO_BASE \
                                | BATL_PP_RW \
                                | BATL_CACHEINHIBIT \
                                | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT5U       (CONFIG_SYS_VIDEO_BASE \
                                | BATU_BL_64M \
                                | BATU_VS \
                                | BATU_VP)
#define CONFIG_SYS_DBAT5L       CONFIG_SYS_IBAT5L
#define CONFIG_SYS_DBAT5U       CONFIG_SYS_IBAT5U

#ifdef CONFIG_PCI
/* PCI MEM space: cacheable */
#define CONFIG_SYS_IBAT6L       (CONFIG_SYS_PCI1_MEM_PHYS \
                                | BATL_PP_RW \
                                | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT6U       (CONFIG_SYS_PCI1_MEM_PHYS \
                                | BATU_BL_256M \
                                | BATU_VS \
                                | BATU_VP)
#define CONFIG_SYS_DBAT6L       CONFIG_SYS_IBAT6L
#define CONFIG_SYS_DBAT6U       CONFIG_SYS_IBAT6U
/* PCI MMIO space: cache-inhibit and guarded */
#define CONFIG_SYS_IBAT7L       (CONFIG_SYS_PCI1_MMIO_PHYS \
                                | BATL_PP_RW \
                                | BATL_CACHEINHIBIT \
                                | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT7U       (CONFIG_SYS_PCI1_MMIO_PHYS \
                                | BATU_BL_256M \
                                | BATU_VS \
                                | BATU_VP)
#define CONFIG_SYS_DBAT7L       CONFIG_SYS_IBAT7L
#define CONFIG_SYS_DBAT7U       CONFIG_SYS_IBAT7U
#else /* CONFIG_PCI */
#define CONFIG_SYS_IBAT6L       (0)
#define CONFIG_SYS_IBAT6U       (0)
#define CONFIG_SYS_IBAT7L       (0)
#define CONFIG_SYS_IBAT7U       (0)
#define CONFIG_SYS_DBAT6L       CONFIG_SYS_IBAT6L
#define CONFIG_SYS_DBAT6U       CONFIG_SYS_IBAT6U
#define CONFIG_SYS_DBAT7L       CONFIG_SYS_IBAT7L
#define CONFIG_SYS_DBAT7U       CONFIG_SYS_IBAT7U
#endif /* CONFIG_PCI */

#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE    230400  /* speed of kgdb serial port */
#define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
#endif

/*
 * Environment Configuration
 */
#define CONFIG_ENV_OVERWRITE

#if defined(CONFIG_UEC_ETH)
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_HAS_ETH2
#define CONFIG_HAS_ETH3
#endif

#define CONFIG_BAUDRATE 115200

#define CONFIG_LOADADDR a00000
#define CONFIG_HOSTNAME mpc8360erdk
#define CONFIG_BOOTFILE "uImage"

#define CONFIG_ROOTPATH         "/nfsroot/"

#define CONFIG_BOOTDELAY 2      /* -1 disables auto-boot */
#undef  CONFIG_BOOTARGS         /* the boot command will set bootargs */

#define CONFIG_EXTRA_ENV_SETTINGS \
        "netdev=eth0\0"                                                 \
        "consoledev=ttyS0\0"                                            \
        "loadaddr=a00000\0"                                             \
        "fdtaddr=900000\0"                                              \
        "fdtfile=mpc836x_rdk.dtb\0"                                     \
        "fsfile=fs\0"                                                   \
        "ubootfile=u-boot.bin\0"                                        \
        "mtdparts=mtdparts=60000000.nand-flash:4096k(kernel),128k(dtb),"\
                                                        "-(rootfs)\0"   \
        "setbootargs=setenv bootargs console=$consoledev,$baudrate "    \
                "$mtdparts panic=1\0"                                   \
        "adddhcpargs=setenv bootargs $bootargs ip=on\0"                 \
        "addnfsargs=setenv bootargs $bootargs ip=$ipaddr:$serverip:"    \
                "$gatewayip:$netmask:$hostname:$netdev:off "            \
                "root=/dev/nfs rw nfsroot=$serverip:$rootpath\0"        \
        "addnandargs=setenv bootargs $bootargs root=/dev/mtdblock3 "    \
                "rootfstype=jffs2 rw\0"                                 \
        "tftp_get_uboot=tftp 100000 $ubootfile\0"                       \
        "tftp_get_kernel=tftp $loadaddr $bootfile\0"                    \
        "tftp_get_dtb=tftp $fdtaddr $fdtfile\0"                         \
        "tftp_get_fs=tftp c00000 $fsfile\0"                             \
        "nand_erase_kernel=nand erase 0 400000\0"                       \
        "nand_erase_dtb=nand erase 400000 20000\0"                      \
        "nand_erase_fs=nand erase 420000 3be0000\0"                     \
        "nand_write_kernel=nand write.jffs2 $loadaddr 0 400000\0"       \
        "nand_write_dtb=nand write.jffs2 $fdtaddr 400000 20000\0"       \
        "nand_write_fs=nand write.jffs2 c00000 420000 $filesize\0"      \
        "nand_read_kernel=nand read.jffs2 $loadaddr 0 400000\0"         \
        "nand_read_dtb=nand read.jffs2 $fdtaddr 400000 20000\0"         \
        "nor_reflash=protect off ff800000 ff87ffff ; "                  \
                "erase ff800000 ff87ffff ; "                            \
                "cp.b 100000 ff800000 $filesize\0"                      \
        "nand_reflash_kernel=run tftp_get_kernel nand_erase_kernel "    \
                "nand_write_kernel\0"                                   \
        "nand_reflash_dtb=run tftp_get_dtb nand_erase_dtb nand_write_dtb\0"\
        "nand_reflash_fs=run tftp_get_fs nand_erase_fs nand_write_fs\0" \
        "nand_reflash=run nand_reflash_kernel nand_reflash_dtb "        \
                "nand_reflash_fs\0"                                     \
        "boot_m=bootm $loadaddr - $fdtaddr\0"                           \
        "dhcpboot=dhcp ; run setbootargs adddhcpargs tftp_get_dtb boot_m\0"\
        "nfsboot=run setbootargs addnfsargs tftp_get_kernel tftp_get_dtb "\
                "boot_m\0"                                              \
        "nandboot=run setbootargs addnandargs nand_read_kernel nand_read_dtb "\
                "boot_m\0"                                              \
        ""

#define CONFIG_BOOTCOMMAND "run dhcpboot"

#endif /* __CONFIG_H */