/*
 * smc911x_eeprom.c - EEPROM interface to SMC911x parts.
 * Only tested on SMSC9118 though ...
 *
 * Copyright 2004-2009 Analog Devices Inc.
 *
 * Licensed under the GPL-2 or later.
 *
 * Based on smc91111_eeprom.c which:
 * Heavily borrowed from the following peoples GPL'ed software:
 *  - Wolfgang Denk, DENX Software Engineering, wd@denx.de
 *       Das U-boot
 *  - Ladislav Michl ladis@linux-mips.org
 *       A rejected patch on the U-Boot mailing list
 */

#include <common.h>
#include <exports.h>
#include <linux/ctype.h>
#include "../drivers/net/smc911x.h"

/**
 *      smsc_ctrlc - detect press of CTRL+C (common ctrlc() isnt exported!?)
 */
static int smsc_ctrlc(void)
{
        return (tstc() && getc() == 0x03);
}

/**
 *      usage - dump usage information
 */
static void usage(void)
{
        puts(
                "MAC/EEPROM Commands:\n"
                " P : Print the MAC addresses\n"
                " D : Dump the EEPROM contents\n"
                " M : Dump the MAC contents\n"
                " C : Copy the MAC address from the EEPROM to the MAC\n"
                " W : Write a register in the EEPROM or in the MAC\n"
                " Q : Quit\n"
                "\n"
                "Some commands take arguments:\n"
                " W <E|M> <register> <value>\n"
                "    E: EEPROM   M: MAC\n"
        );
}

/**
 *      dump_regs - dump the MAC registers
 *
 * Registers 0x00 - 0x50 are FIFOs.  The 0x50+ are the control registers
 * and they're all 32bits long.  0xB8+ are reserved, so don't bother.
 */
static void dump_regs(struct eth_device *dev)
{
        u8 i, j = 0;
        for (i = 0x50; i < 0xB8; i += sizeof(u32))
                printf("%02x: 0x%08x %c", i,
                        smc911x_reg_read(dev, i),
                        (j++ % 2 ? '\n' : ' '));
}

/**
 *      do_eeprom_cmd - handle eeprom communication
 */
static int do_eeprom_cmd(struct eth_device *dev, int cmd, u8 reg)
{
        if (smc911x_reg_read(dev, E2P_CMD) & E2P_CMD_EPC_BUSY) {
                printf("eeprom_cmd: busy at start (E2P_CMD = 0x%08x)\n",
                        smc911x_reg_read(dev, E2P_CMD));
                return -1;
        }

        smc911x_reg_write(dev, E2P_CMD, E2P_CMD_EPC_BUSY | cmd | reg);

        while (smc911x_reg_read(dev, E2P_CMD) & E2P_CMD_EPC_BUSY)
                if (smsc_ctrlc()) {
                        printf("eeprom_cmd: timeout (E2P_CMD = 0x%08x)\n",
                                smc911x_reg_read(dev, E2P_CMD));
                        return -1;
                }

        return 0;
}

/**
 *      read_eeprom_reg - read specified register in EEPROM
 */
static u8 read_eeprom_reg(struct eth_device *dev, u8 reg)
{
        int ret = do_eeprom_cmd(dev, E2P_CMD_EPC_CMD_READ, reg);
        return (ret ? : smc911x_reg_read(dev, E2P_DATA));
}

/**
 *      write_eeprom_reg - write specified value into specified register in EEPROM
 */
static int write_eeprom_reg(struct eth_device *dev, u8 value, u8 reg)
{
        int ret;

        /* enable erasing/writing */
        ret = do_eeprom_cmd(dev, E2P_CMD_EPC_CMD_EWEN, reg);
        if (ret)
                goto done;

        /* erase the eeprom reg */
        ret = do_eeprom_cmd(dev, E2P_CMD_EPC_CMD_ERASE, reg);
        if (ret)
                goto done;

        /* write the eeprom reg */
        smc911x_reg_write(dev, E2P_DATA, value);
        ret = do_eeprom_cmd(dev, E2P_CMD_EPC_CMD_WRITE, reg);
        if (ret)
                goto done;

        /* disable erasing/writing */
        ret = do_eeprom_cmd(dev, E2P_CMD_EPC_CMD_EWDS, reg);

 done:
        return ret;
}

/**
 *      skip_space - find first non-whitespace in given pointer
 */
static char *skip_space(char *buf)
{
        while (isblank(buf[0]))
                ++buf;
        return buf;
}

/**
 *      write_stuff - handle writing of MAC registers / eeprom
 */
static void write_stuff(struct eth_device *dev, char *line)
{
        char dest;
        char *endp;
        u8 reg;
        u32 value;

        /* Skip over the "W " part of the command */
        line = skip_space(line + 1);

        /* Figure out destination */
        switch (line[0]) {
        case 'E':
        case 'M':
                dest = line[0];
                break;
        default:
        invalid_usage:
                printf("ERROR: Invalid write usage\n");
                usage();
                return;
        }

        /* Get the register to write */
        line = skip_space(line + 1);
        reg = simple_strtoul(line, &endp, 16);
        if (line == endp)
                goto invalid_usage;

        /* Get the value to write */
        line = skip_space(endp);
        value = simple_strtoul(line, &endp, 16);
        if (line == endp)
                goto invalid_usage;

        /* Check for trailing cruft */
        line = skip_space(endp);
        if (line[0])
                goto invalid_usage;

        /* Finally, execute the command */
        if (dest == 'E') {
                printf("Writing EEPROM register %02x with %02x\n", reg, value);
                write_eeprom_reg(dev, value, reg);
        } else {
                printf("Writing MAC register %02x with %08x\n", reg, value);
                smc911x_reg_write(dev, reg, value);
        }
}

/**
 *      copy_from_eeprom - copy MAC address in eeprom to address registers
 */
static void copy_from_eeprom(struct eth_device *dev)
{
        ulong addrl =
                read_eeprom_reg(dev, 0x01) |
                read_eeprom_reg(dev, 0x02) << 8 |
                read_eeprom_reg(dev, 0x03) << 16 |
                read_eeprom_reg(dev, 0x04) << 24;
        ulong addrh =
                read_eeprom_reg(dev, 0x05) |
                read_eeprom_reg(dev, 0x06) << 8;
        smc911x_set_mac_csr(dev, ADDRL, addrl);
        smc911x_set_mac_csr(dev, ADDRH, addrh);
        puts("EEPROM contents copied to MAC\n");
}

/**
 *      print_macaddr - print MAC address registers and MAC address in eeprom
 */
static void print_macaddr(struct eth_device *dev)
{
        puts("Current MAC Address in MAC:     ");
        ulong addrl = smc911x_get_mac_csr(dev, ADDRL);
        ulong addrh = smc911x_get_mac_csr(dev, ADDRH);
        printf("%02x:%02x:%02x:%02x:%02x:%02x\n",
                (u8)(addrl), (u8)(addrl >> 8), (u8)(addrl >> 16),
                (u8)(addrl >> 24), (u8)(addrh), (u8)(addrh >> 8));

        puts("Current MAC Address in EEPROM:  ");
        int i;
        for (i = 1; i < 6; ++i)
                printf("%02x:", read_eeprom_reg(dev, i));
        printf("%02x\n", read_eeprom_reg(dev, i));
}

/**
 *      dump_eeprom - dump the whole content of the EEPROM
 */
static void dump_eeprom(struct eth_device *dev)
{
        int i;
        puts("EEPROM:\n");
        for (i = 0; i < 7; ++i)
                printf("%02x: 0x%02x\n", i, read_eeprom_reg(dev, i));
}

/**
 *      smc911x_init - get the MAC/EEPROM up and ready for use
 */
static int smc911x_init(struct eth_device *dev)
{
        /* See if there is anything there */
        if (smc911x_detect_chip(dev))
                return 1;

        smc911x_reset(dev);

        /* Make sure we set EEDIO/EECLK to the EEPROM */
        if (smc911x_reg_read(dev, GPIO_CFG) & GPIO_CFG_EEPR_EN) {
                while (smc911x_reg_read(dev, E2P_CMD) & E2P_CMD_EPC_BUSY)
                        if (smsc_ctrlc()) {
                                printf("init: timeout (E2P_CMD = 0x%08x)\n",
                                        smc911x_reg_read(dev, E2P_CMD));
                                return 1;
                        }
                smc911x_reg_write(dev, GPIO_CFG,
                        smc911x_reg_read(dev, GPIO_CFG) & ~GPIO_CFG_EEPR_EN);
        }

        return 0;
}

/**
 *      getline - consume a line of input and handle some escape sequences
 */
static char *getline(void)
{
        static char buffer[100];
        char c;
        size_t i;

        i = 0;
        while (1) {
                buffer[i] = '\0';
                while (!tstc())
                        continue;

                c = getc();
                /* Convert to uppercase */
                if (c >= 'a' && c <= 'z')
                        c -= ('a' - 'A');

                switch (c) {
                case '\r':      /* Enter/Return key */
                case '\n':
                        puts("\n");
                        return buffer;

                case 0x03:      /* ^C - break */
                        return NULL;

                case 0x5F:
                case 0x08:      /* ^H  - backspace */
                case 0x7F:      /* DEL - backspace */
                        if (i) {
                                puts("\b \b");
                                i--;
                        }
                        break;

                default:
                        /* Ignore control characters */
                        if (c < 0x20)
                                break;
                        /* Queue up all other characters */
                        buffer[i++] = c;
                        printf("%c", c);
                        break;
                }
        }
}

/**
 *      smc911x_eeprom - our application's main() function
 */
int smc911x_eeprom(int argc, char * const argv[])
{
        /* Avoid initializing on stack as gcc likes to call memset() */
        struct eth_device dev;
        dev.iobase = CONFIG_SMC911X_BASE;

        /* Print the ABI version */
        app_startup(argv);
        if (XF_VERSION != get_version()) {
                printf("Expects ABI version %d\n", XF_VERSION);
                printf("Actual U-Boot ABI version %lu\n", get_version());
                printf("Can't run\n\n");
                return 1;
        }

        /* Initialize the MAC/EEPROM somewhat */
        puts("\n");
        if (smc911x_init(&dev))
                return 1;

        /* Dump helpful usage information */
        puts("\n");
        usage();
        puts("\n");

        while (1) {
                char *line;

                /* Send the prompt and wait for a line */
                puts("eeprom> ");
                line = getline();

                /* Got a ctrl+c */
                if (!line)
                        return 0;

                /* Eat leading space */
                line = skip_space(line);

                /* Empty line, try again */
                if (!line[0])
                        continue;

                /* Only accept 1 letter commands */
                if (line[0] && line[1] && !isblank(line[1]))
                        goto unknown_cmd;

                /* Now parse the command */
                switch (line[0]) {
                case 'W': write_stuff(&dev, line); break;
                case 'D': dump_eeprom(&dev);       break;
                case 'M': dump_regs(&dev);         break;
                case 'C': copy_from_eeprom(&dev);  break;
                case 'P': print_macaddr(&dev);     break;
                unknown_cmd:
                default:  puts("ERROR: Unknown command!\n\n");
                case '?':
                case 'H': usage();            break;
                case 'Q': return 0;
                }
        }
}