/*
 * Copyright (C) 2009-2010 Freescale Semiconductor, Inc.
 * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com
 *
 *
 * See file CREDITS for list of people who contributed to this
 * project.
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 * MA 02111-1307 USA
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * High Level Configuration Options
 */
#define CONFIG_E300             1 /* E300 family */
#define CONFIG_MPC83xx          1 /* MPC83xx family */
#define CONFIG_MPC8308          1 /* MPC8308 CPU specific */
#define CONFIG_MPC8308_P1M      1 /* mpc8308_p1m board specific */

#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE    0xFC000000
#endif

/*
 * On-board devices
 *
 * TSECs
 */
#define CONFIG_TSEC1
#define CONFIG_TSEC2

/*
 * System Clock Setup
 */
#define CONFIG_83XX_CLKIN       33333333 /* in Hz */
#define CONFIG_SYS_CLK_FREQ     CONFIG_83XX_CLKIN

/*
 * Hardware Reset Configuration Word
 * if CLKIN is 66.66MHz, then
 * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
 * We choose the A type silicon as default, so the core is 400Mhz.
 */
#define CONFIG_SYS_HRCW_LOW (\
        HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
        HRCWL_DDR_TO_SCB_CLK_2X1 |\
        HRCWL_SVCOD_DIV_2 |\
        HRCWL_CSB_TO_CLKIN_4X1 |\
        HRCWL_CORE_TO_CSB_3X1)
/*
 * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
 * in 8308's HRCWH according to the manual, but original Freescale's
 * code has them and I've expirienced some problems using the board
 * with BDI3000 attached when I've tried to set these bits to zero
 * (UART doesn't work after the 'reset run' command).
 */
#define CONFIG_SYS_HRCW_HIGH (\
        HRCWH_PCI_HOST |\
        HRCWH_PCI1_ARBITER_ENABLE |\
        HRCWH_CORE_ENABLE |\
        HRCWH_FROM_0X00000100 |\
        HRCWH_BOOTSEQ_DISABLE |\
        HRCWH_SW_WATCHDOG_DISABLE |\
        HRCWH_ROM_LOC_LOCAL_16BIT |\
        HRCWH_RL_EXT_LEGACY |\
        HRCWH_TSEC1M_IN_MII |\
        HRCWH_TSEC2M_IN_MII |\
        HRCWH_BIG_ENDIAN)

/*
 * System IO Config
 */
#define CONFIG_SYS_SICRH (\
        SICRH_ESDHC_A_GPIO |\
        SICRH_ESDHC_B_GPIO |\
        SICRH_ESDHC_C_GTM |\
        SICRH_GPIO_A_TSEC2 |\
        SICRH_GPIO_B_TSEC2_TX_CLK |\
        SICRH_IEEE1588_A_GPIO |\
        SICRH_USB |\
        SICRH_GTM_GPIO |\
        SICRH_IEEE1588_B_GPIO |\
        SICRH_ETSEC2_CRS |\
        SICRH_GPIOSEL_1 |\
        SICRH_TMROBI_V3P3 |\
        SICRH_TSOBI1_V3P3 |\
        SICRH_TSOBI2_V3P3)      /* 0xf577d100 */
#define CONFIG_SYS_SICRL (\
        SICRL_SPI_PF0 |\
        SICRL_UART_PF0 |\
        SICRL_IRQ_PF0 |\
        SICRL_I2C2_PF0 |\
        SICRL_ETSEC1_TX_CLK)    /* 0x00000000 */

#define CONFIG_SYS_GPIO1_PRELIM
/* GPIO Default input/output settings */
#define CONFIG_SYS_GPIO1_DIR        0x7AAF8C00
/*
 * Default GPIO values:
 * LED#1 enabled; WLAN enabled; Both COM LED on (orange)
 */
#define CONFIG_SYS_GPIO1_DAT        0x08008C00

/*
 * IMMR new address
 */
#define CONFIG_SYS_IMMR         0xE0000000

/*
 * SERDES
 */
#define CONFIG_FSL_SERDES
#define CONFIG_FSL_SERDES1      0xe3000

/*
 * Arbiter Setup
 */
#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */
#define CONFIG_SYS_ACR_RPTCNT   3 /* Arbiter repeat count is 4 */
#define CONFIG_SYS_SPCR_TSECEP  3 /* eTSEC emergency priority is highest */

/*
 * DDR Setup
 */
#define CONFIG_SYS_DDR_BASE             0x00000000 /* DDR is system memory */
#define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE       CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
                                | DDRCDR_PZ_LOZ \
                                | DDRCDR_NZ_LOZ \
                                | DDRCDR_ODT \
                                | DDRCDR_Q_DRN)
                                /* 0x7b880001 */
/*
 * Manually set up DDR parameters
 * consist of two chips HY5PS12621BFP-C4 from HYNIX
 */

#define CONFIG_SYS_DDR_SIZE             128 /* MB */

#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
#define CONFIG_SYS_DDR_CS0_CONFIG       (CSCONFIG_EN \
                                        | CSCONFIG_ODT_RD_NEVER \
                                        | CSCONFIG_ODT_WR_ONLY_CURRENT \
                                        | CSCONFIG_ROW_BIT_13 \
                                        | CSCONFIG_COL_BIT_10)
                                        /* 0x80010102 */
#define CONFIG_SYS_DDR_TIMING_3 0x00000000
#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
                                | (0 << TIMING_CFG0_WRT_SHIFT) \
                                | (0 << TIMING_CFG0_RRT_SHIFT) \
                                | (0 << TIMING_CFG0_WWT_SHIFT) \
                                | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
                                | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
                                | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
                                | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
                                /* 0x00220802 */
#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
                                | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
                                | (2 << TIMING_CFG1_ACTTORW_SHIFT) \
                                | (5 << TIMING_CFG1_CASLAT_SHIFT) \
                                | (6 << TIMING_CFG1_REFREC_SHIFT) \
                                | (2 << TIMING_CFG1_WRREC_SHIFT) \
                                | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
                                | (2 << TIMING_CFG1_WRTORD_SHIFT))
                                /* 0x27256222 */
#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
                                | (4 << TIMING_CFG2_CPO_SHIFT) \
                                | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
                                | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
                                | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
                                | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
                                | (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
                                /* 0x121048c5 */
#define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
                                | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
                                /* 0x03600100 */
#define CONFIG_SYS_DDR_SDRAM_CFG        (SDRAM_CFG_SREN \
                                | SDRAM_CFG_SDRAM_TYPE_DDR2 \
                                | SDRAM_CFG_DBW_32)
                                /* 0x43080000 */

#define CONFIG_SYS_DDR_SDRAM_CFG2       0x00401000 /* 1 posted refresh */
#define CONFIG_SYS_DDR_MODE             ((0x0448 << SDRAM_MODE_ESD_SHIFT) \
                                | (0x0232 << SDRAM_MODE_SD_SHIFT))
                                /* ODT 150ohm CL=3, AL=1 on SDRAM */
#define CONFIG_SYS_DDR_MODE2            0x00000000

/*
 * Memory test
 */
#define CONFIG_SYS_MEMTEST_START        0x00001000 /* memtest region */
#define CONFIG_SYS_MEMTEST_END          0x07f00000

/*
 * The reserved memory
 */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */

#define CONFIG_SYS_MONITOR_LEN  (384 * 1024) /* Reserve 384 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN   (512 * 1024) /* Reserved for malloc */

/*
 * Initial RAM Base Address Setup
 */
#define CONFIG_SYS_INIT_RAM_LOCK        1
#define CONFIG_SYS_INIT_RAM_ADDR        0xE6000000 /* Initial RAM address */
#define CONFIG_SYS_INIT_RAM_SIZE        0x1000 /* Size of used area in RAM */
#define CONFIG_SYS_GBL_DATA_OFFSET      \
        (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)

/*
 * Local Bus Configuration & Clock Setup
 */
#define CONFIG_SYS_LCRR_DBYP            LCRR_DBYP
#define CONFIG_SYS_LCRR_CLKDIV          LCRR_CLKDIV_2
#define CONFIG_SYS_LBC_LBCR             0x00040000

/*
 * FLASH on the Local Bus
 */
#define CONFIG_SYS_FLASH_CFI            /* use the Common Flash Interface */
#define CONFIG_FLASH_CFI_DRIVER         /* use the CFI driver */
#define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_16BIT

#define CONFIG_SYS_FLASH_BASE           0xFC000000 /* FLASH base address */
#define CONFIG_SYS_FLASH_SIZE           64 /* FLASH size is 64M */
#define CONFIG_SYS_FLASH_PROTECTION     1 /* Use h/w Flash protection. */

/* Window base at flash base */
#define CONFIG_SYS_LBLAWBAR0_PRELIM     CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_LBLAWAR0_PRELIM      (LBLAWAR_EN | LBLAWAR_64MB)

#define CONFIG_SYS_BR0_PRELIM   (CONFIG_SYS_FLASH_BASE \
                                | BR_PS_16      /* 16 bit port */ \
                                | BR_MS_GPCM    /* MSEL = GPCM */ \
                                | BR_V)         /* valid */
#define CONFIG_SYS_OR0_PRELIM   (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
                                | OR_UPM_XAM \
                                | OR_GPCM_CSNT \
                                | OR_GPCM_ACS_DIV2 \
                                | OR_GPCM_XACS \
                                | OR_GPCM_SCY_4 \
                                | OR_GPCM_TRLX_SET \
                                | OR_GPCM_EHTR_SET)

#define CONFIG_SYS_MAX_FLASH_BANKS      1 /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT       512

/* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_ERASE_TOUT     (1000 * 1024)
/* Flash Write Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT     (500 * 1024)

/*
 * SJA1000 CAN controller on Local Bus
 */
#define CONFIG_SYS_SJA1000_BASE 0xFBFF0000
#define CONFIG_SYS_BR1_PRELIM   (CONFIG_SYS_SJA1000_BASE \
                                | BR_PS_8       /* 8 bit port size */ \
                                | BR_MS_GPCM    /* MSEL = GPCM */ \
                                | BR_V)         /* valid */
#define CONFIG_SYS_OR1_PRELIM   (OR_AM_32KB \
                                | OR_GPCM_SCY_5 \
                                | OR_GPCM_EHTR_SET)
                                /* 0xFFFF8052 */

#define CONFIG_SYS_LBLAWBAR1_PRELIM     CONFIG_SYS_SJA1000_BASE
#define CONFIG_SYS_LBLAWAR1_PRELIM      (LBLAWAR_EN | LBLAWAR_32KB)

/*
 * CPLD on Local Bus
 */
#define CONFIG_SYS_CPLD_BASE    0xFBFF8000
#define CONFIG_SYS_BR2_PRELIM   (CONFIG_SYS_CPLD_BASE \
                                | BR_PS_8       /* 8 bit port */ \
                                | BR_MS_GPCM    /* MSEL = GPCM */ \
                                | BR_V)         /* valid */
#define CONFIG_SYS_OR2_PRELIM   (OR_AM_32KB \
                                | OR_GPCM_SCY_4 \
                                | OR_GPCM_EHTR_SET)
                                /* 0xFFFF8042 */

#define CONFIG_SYS_LBLAWBAR2_PRELIM     CONFIG_SYS_CPLD_BASE
#define CONFIG_SYS_LBLAWAR2_PRELIM      (LBLAWAR_EN | LBLAWAR_32KB)

/*
 * Serial Port
 */
#define CONFIG_CONS_INDEX       1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE     1
#define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)

#define CONFIG_SYS_BAUDRATE_TABLE  \
        {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)

/* Use the HUSH parser */
#define CONFIG_SYS_HUSH_PARSER

/* Pass open firmware flat tree */
#define CONFIG_OF_LIBFDT        1
#define CONFIG_OF_BOARD_SETUP   1
#define CONFIG_OF_STDOUT_VIA_ALIAS      1

/* I2C */
#define CONFIG_HARD_I2C         /* I2C with hardware support */
#define CONFIG_FSL_I2C
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_SYS_I2C_SPEED    400000 /* I2C speed and slave address */
#define CONFIG_SYS_I2C_SLAVE    0x7F
#define CONFIG_SYS_I2C_OFFSET   0x3000
#define CONFIG_SYS_I2C2_OFFSET  0x3100

/*
 * General PCI
 * Addresses are mapped 1-1.
 */
#define CONFIG_SYS_PCIE1_BASE           0xA0000000
#define CONFIG_SYS_PCIE1_MEM_BASE       0xA0000000
#define CONFIG_SYS_PCIE1_MEM_PHYS       0xA0000000
#define CONFIG_SYS_PCIE1_MEM_SIZE       0x10000000
#define CONFIG_SYS_PCIE1_CFG_BASE       0xB0000000
#define CONFIG_SYS_PCIE1_CFG_SIZE       0x01000000
#define CONFIG_SYS_PCIE1_IO_BASE        0x00000000
#define CONFIG_SYS_PCIE1_IO_PHYS        0xB1000000
#define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000

/* enable PCIE clock */
#define CONFIG_SYS_SCCR_PCIEXP1CM       1

#define CONFIG_PCI
#define CONFIG_PCIE

#define CONFIG_PCI_PNP          /* do pci plug-and-play */

#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957   /* Freescale */
#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1

/*
 * TSEC
 */
#define CONFIG_TSEC_ENET        /* TSEC ethernet support */
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
#define CONFIG_SYS_TSEC1        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
#define CONFIG_SYS_TSEC2_OFFSET 0x25000
#define CONFIG_SYS_TSEC2        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)

/*
 * TSEC ethernet configuration
 */
#define CONFIG_MII              1 /* MII PHY management */
#define CONFIG_TSEC1_NAME       "eTSEC0"
#define CONFIG_TSEC2_NAME       "eTSEC1"
#define TSEC1_PHY_ADDR          1
#define TSEC2_PHY_ADDR          2
#define TSEC1_PHYIDX            0
#define TSEC2_PHYIDX            0
#define TSEC1_FLAGS             0
#define TSEC2_FLAGS             0

/* Options are: eTSEC[0-1] */
#define CONFIG_ETHPRIME         "eTSEC0"

/*
 * Environment
 */
#define CONFIG_ENV_IS_IN_FLASH  1
#define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + \
                                 CONFIG_SYS_MONITOR_LEN)
#define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K(one sector) for env */
#define CONFIG_ENV_SIZE         0x2000
#define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND  CONFIG_ENV_SIZE

#define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */

/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME

/*
 * Command line configuration.
 */
#include <config_cmd_default.h>

#define CONFIG_CMD_DHCP
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
#define CONFIG_CMD_NET
#define CONFIG_CMD_PCI
#define CONFIG_CMD_PING

#define CONFIG_CMDLINE_EDITING  1       /* add command line history */

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP             /* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR            0x2000000 /* default load address */
#define CONFIG_SYS_PROMPT               "=> "   /* Monitor Command Prompt */

#define CONFIG_SYS_CBSIZE       1024 /* Console I/O Buffer Size */

/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS      16      /* max number of command args */
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
#define CONFIG_SYS_HZ           1000    /* decrementer freq: 1ms ticks */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ    (256 << 20) /* Initial Memory map for Linux */

/*
 * Core HID Setup
 */
#define CONFIG_SYS_HID0_INIT    0x000000000
#define CONFIG_SYS_HID0_FINAL   (HID0_ENABLE_MACHINE_CHECK | \
                                 HID0_ENABLE_INSTRUCTION_CACHE | \
                                 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
#define CONFIG_SYS_HID2         HID2_HBE

/*
 * MMU Setup
 */

/* DDR: cache cacheable */
#define CONFIG_SYS_IBAT0L       (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
                                        BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT0U       (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
                                        BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT0L       CONFIG_SYS_IBAT0L
#define CONFIG_SYS_DBAT0U       CONFIG_SYS_IBAT0U

/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
#define CONFIG_SYS_IBAT1L       (CONFIG_SYS_IMMR | BATL_PP_RW | \
                        BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT1U       (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
                                        BATU_VP)
#define CONFIG_SYS_DBAT1L       CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U       CONFIG_SYS_IBAT1U

/* FLASH: icache cacheable, but dcache-inhibit and guarded */
#define CONFIG_SYS_IBAT2L       (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
                                        BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT2U       (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
                                        BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT2L       (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
                                        BATL_CACHEINHIBIT | \
                                        BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT2U       CONFIG_SYS_IBAT2U

/* Stack in dcache: cacheable, no memory coherence */
#define CONFIG_SYS_IBAT3L       (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
#define CONFIG_SYS_IBAT3U       (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
                                        BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT3L       CONFIG_SYS_IBAT3L
#define CONFIG_SYS_DBAT3U       CONFIG_SYS_IBAT3U

/*
 * Environment Configuration
 */

#define CONFIG_ENV_OVERWRITE

#if defined(CONFIG_TSEC_ENET)
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#endif

#define CONFIG_BAUDRATE 115200

#define CONFIG_LOADADDR 800000  /* default location for tftp and bootm */

#define CONFIG_BOOTDELAY        5       /* -1 disables auto-boot */

#define xstr(s) str(s)
#define str(s)  #s

#define CONFIG_EXTRA_ENV_SETTINGS                                       \
        "netdev=eth0\0"                                                 \
        "consoledev=ttyS0\0"                                            \
        "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
                "nfsroot=${serverip}:${rootpath}\0"                     \
        "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
        "addip=setenv bootargs ${bootargs} "                            \
                "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
                ":${hostname}:${netdev}:off panic=1\0"                  \
        "addtty=setenv bootargs ${bootargs}"                            \
                " console=${consoledev},${baudrate}\0"                  \
        "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"              \
        "addmisc=setenv bootargs ${bootargs}\0"                         \
        "kernel_addr=FC0A0000\0"                                        \
        "fdt_addr=FC2A0000\0"                                           \
        "ramdisk_addr=FC2C0000\0"                                       \
        "u-boot=mpc8308_p1m/u-boot.bin\0"                               \
        "kernel_addr_r=1000000\0"                                       \
        "fdt_addr_r=C00000\0"                                           \
        "hostname=mpc8308_p1m\0"                                        \
        "bootfile=mpc8308_p1m/uImage\0"                                 \
        "fdtfile=mpc8308_p1m/mpc8308_p1m.dtb\0"                         \
        "rootpath=/opt/eldk-4.2/ppc_6xx\0"                              \
        "flash_self=run ramargs addip addtty addmtd addmisc;"           \
                "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"    \
        "flash_nfs=run nfsargs addip addtty addmtd addmisc;"            \
                "bootm ${kernel_addr} - ${fdt_addr}\0"                  \
        "net_nfs=tftp ${kernel_addr_r} ${bootfile};"                    \
                "tftp ${fdt_addr_r} ${fdtfile};"                        \
                "run nfsargs addip addtty addmtd addmisc;"              \
                "bootm ${kernel_addr_r} - ${fdt_addr_r}\0"              \
        "bootcmd=run flash_self\0"                                      \
        "load=tftp ${loadaddr} ${u-boot}\0"                             \
        "update=protect off " xstr(CONFIG_SYS_MONITOR_BASE)             \
                " +${filesize};era " xstr(CONFIG_SYS_MONITOR_BASE)      \
                " +${filesize};cp.b ${fileaddr} "                       \
                xstr(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0"          \
        "upd=run load update\0"                                         \

#endif  /* __CONFIG_H */