/*
 * (C) Copyright 2001
 * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
 *
 * See file CREDITS for list of people who contributed to this
 * project.
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 * MA 02111-1307 USA
 */

/*
 * board/config.h - configuration options, board specific
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * High Level Configuration Options
 * (easy to change)
 */

#define CONFIG_405GP            1       /* This is a PPC405 CPU         */
#define CONFIG_4xx              1       /* ...member of PPC4xx family   */
#define CONFIG_CPCI405          1       /* ...on a CPCI405 board        */

#define CONFIG_SYS_TEXT_BASE    0xFFFC0000

#define CONFIG_BOARD_EARLY_INIT_F 1     /* call board_early_init_f()    */
#define CONFIG_MISC_INIT_R       1      /* call misc_init_r()           */

#define CONFIG_SYS_CLK_FREQ     33000000 /* external frequency to pll   */

#define CONFIG_BAUDRATE         9600
#define CONFIG_BOOTDELAY        3       /* autoboot after 3 seconds     */

#undef  CONFIG_BOOTARGS
#undef  CONFIG_BOOTCOMMAND

#define CONFIG_PREBOOT                  /* enable preboot variable      */

#define CONFIG_LOADS_ECHO       1       /* echo on for serial download  */
#define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change        */

#define CONFIG_PPC4xx_EMAC
#define CONFIG_MII              1       /* MII PHY management           */
#define CONFIG_PHY_ADDR         0       /* PHY address                  */
#define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
#define CONFIG_RESET_PHY_R      1       /* use reset_phy() to disable phy sleep mode */

#undef  CONFIG_HAS_ETH1

/*
 * BOOTP options
 */
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_DNS
#define CONFIG_BOOTP_DNS2
#define CONFIG_BOOTP_SEND_HOSTNAME


/*
 * Command line configuration.
 */
#include <config_cmd_default.h>

#define CONFIG_CMD_DHCP
#define CONFIG_CMD_PCI
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_IDE
#define CONFIG_CMD_FAT
#define CONFIG_CMD_ELF
#define CONFIG_CMD_MII
#define CONFIG_CMD_EEPROM


#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION

#define CONFIG_SUPPORT_VFAT

#undef  CONFIG_WATCHDOG                 /* watchdog disabled            */

#define CONFIG_SDRAM_BANK0      1       /* init onboard SDRAM bank 0    */

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP                     /* undef to save memory         */
#define CONFIG_SYS_PROMPT       "=> "           /* Monitor Command Prompt       */

#undef  CONFIG_SYS_HUSH_PARSER                  /* use "hush" command parser    */

#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size      */
#else
#define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size      */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS      16              /* max number of command args   */
#define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */

#define CONFIG_SYS_DEVICE_NULLDEV       1       /* include nulldev device       */

#define CONFIG_SYS_CONSOLE_INFO_QUIET   1       /* don't print console @ startup*/

#define CONFIG_SYS_MEMTEST_START        0x0400000       /* memtest works on     */
#define CONFIG_SYS_MEMTEST_END          0x0C00000       /* 4 ... 12 MB in DRAM  */

#define CONFIG_CONS_INDEX       1       /* Use UART0                    */
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE     1
#define CONFIG_SYS_NS16550_CLK          get_serial_clock()

#undef  CONFIG_SYS_EXT_SERIAL_CLOCK            /* no external serial clock used */
#define CONFIG_SYS_BASE_BAUD        691200

/* The following table includes the supported baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE       \
        { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
         57600, 115200, 230400, 460800, 921600 }

#define CONFIG_SYS_LOAD_ADDR    0x100000        /* default load address */
#define CONFIG_SYS_EXTBDINFO    1               /* To use extended board_into (bd_t) */

#define CONFIG_SYS_HZ           1000            /* decrementer freq: 1 ms ticks */

#define CONFIG_LOOPW            1       /* enable loopw command         */

#define CONFIG_ZERO_BOOTDELAY_CHECK     /* check for keypress on bootdelay==0 */

/*-----------------------------------------------------------------------
 * PCI stuff
 *-----------------------------------------------------------------------
 */
#define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
#define PCI_HOST_FORCE  1               /* configure as pci host        */
#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */

#define CONFIG_PCI                      /* include pci support          */
#define CONFIG_PCI_HOST PCI_HOST_AUTO   /* select pci host function     */
#define CONFIG_PCI_PNP                  /* do pci plug-and-play         */
                                        /* resource configuration       */

#define CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */

#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/

#define CONFIG_PCI_BOOTDELAY    0       /* enable pci bootdelay variable*/

#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405  /* PCI Device ID: CPCI-405      */
#define CONFIG_SYS_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A    */
#define CONFIG_SYS_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
#define CONFIG_SYS_PCI_PTM1LA  (bd->bi_memstart) /* point to sdram               */
#define CONFIG_SYS_PCI_PTM1MS  (~(bd->bi_memsize - 1) | 1) /* memsize, enable hard-wired to 1 */
#define CONFIG_SYS_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
#define CONFIG_SYS_PCI_PTM2LA  0xffc00000      /* point to flash               */
#define CONFIG_SYS_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
#define CONFIG_SYS_PCI_PTM2PCI (bd->bi_memsize) /* host use this pci address */

#define CONFIG_PCI_4xx_PTM_OVERWRITE    1 /* overwrite PTMx settings by env */

/*-----------------------------------------------------------------------
 * IDE/ATA stuff
 *-----------------------------------------------------------------------
 */
#undef  CONFIG_IDE_8xx_DIRECT               /* no pcmcia interface required */
#undef  CONFIG_IDE_LED                  /* no led for ide supported     */
#undef  CONFIG_IDE_RESET                /* no reset for ide supported   */

#define CONFIG_SYS_IDE_MAXBUS           1               /* max. 1 IDE busses    */
#define CONFIG_SYS_IDE_MAXDEVICE        (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */

#define CONFIG_SYS_ATA_BASE_ADDR        0xF0100000
#define CONFIG_SYS_ATA_IDE0_OFFSET      0x0000

#define CONFIG_SYS_ATA_DATA_OFFSET      0x0000  /* Offset for data I/O                  */
#define CONFIG_SYS_ATA_REG_OFFSET       0x0000  /* Offset for normal register accesses  */
#define CONFIG_SYS_ATA_ALT_OFFSET       0x0000  /* Offset for alternate registers       */

/*-----------------------------------------------------------------------
 * Start addresses for the final memory configuration
 * (Set up by the startup code)
 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 */
#define CONFIG_SYS_SDRAM_BASE           0x00000000
#define CONFIG_SYS_FLASH_BASE           CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_MONITOR_LEN          (~(CONFIG_SYS_TEXT_BASE) + 1)
#define CONFIG_SYS_MALLOC_LEN           (128 * 1024)    /* Reserve 128 kB for malloc()  */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
 * FLASH organization
 */
#define CONFIG_SYS_MAX_FLASH_BANKS      2       /* max number of memory banks           */
#define CONFIG_SYS_MAX_FLASH_SECT       256     /* max number of sectors on one chip    */

#define CONFIG_SYS_FLASH_ERASE_TOUT     120000  /* Timeout for Flash Erase (in ms)      */
#define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Timeout for Flash Write (in ms)      */

#define CONFIG_SYS_FLASH_WORD_SIZE      unsigned short  /* flash word size (width)      */
#define CONFIG_SYS_FLASH_ADDR0          0x5555  /* 1st address for flash config cycles  */
#define CONFIG_SYS_FLASH_ADDR1          0x2AAA  /* 2nd address for flash config cycles  */
/*
 * The following defines are added for buggy IOP480 byte interface.
 * All other boards should use the standard values (CPCI405 etc.)
 */
#define CONFIG_SYS_FLASH_READ0          0x0000  /* 0 is standard                        */
#define CONFIG_SYS_FLASH_READ1          0x0001  /* 1 is standard                        */
#define CONFIG_SYS_FLASH_READ2          0x0002  /* 2 is standard                        */

#define CONFIG_SYS_FLASH_EMPTY_INFO             /* print 'E' for empty sector on flinfo */

#define CONFIG_SYS_NVRAM_BASE_ADDR      0xf0200000              /* NVRAM base address   */
#define CONFIG_SYS_NVRAM_SIZE           (32*1024)               /* NVRAM size           */
#define CONFIG_SYS_VXWORKS_MAC_PTR     (CONFIG_SYS_NVRAM_BASE_ADDR+0x6900) /* VxWorks eth-addr*/

#if 1 /* Use NVRAM for environment variables */
/*-----------------------------------------------------------------------
 * NVRAM organization
 */
#define CONFIG_ENV_IS_IN_NVRAM  1       /* use NVRAM for environment vars       */
#define CONFIG_ENV_SIZE         0x1000          /* Size of Environment vars     */
#define CONFIG_ENV_ADDR         \
        (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE)      /* Env  */

#else /* Use EEPROM for environment variables */

#define CONFIG_ENV_IS_IN_EEPROM    1       /* use EEPROM for environment vars */
#define CONFIG_ENV_OFFSET          0x000   /* environment starts at the beginning of the EEPROM */
#define CONFIG_ENV_SIZE            0x400   /* 1024 bytes may be used for env vars */
                                   /* total size of a CAT24WC08 is 1024 bytes */
#endif

/*-----------------------------------------------------------------------
 * I2C EEPROM (CAT24WC08) for environment
 */
#define CONFIG_HARD_I2C                 /* I2c with hardware support */
#define CONFIG_PPC4XX_I2C               /* use PPC4xx driver            */
#define CONFIG_SYS_I2C_SPEED            400000  /* I2C speed and slave address */
#define CONFIG_SYS_I2C_SLAVE            0x7F

#define CONFIG_SYS_I2C_EEPROM_ADDR      0x50    /* EEPROM CAT28WC08             */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1        /* Bytes of address             */
/* mask of address bits that overflow into the "EEPROM chip address"    */
#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW     0x07
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4     /* The Catalyst CAT24WC08 has   */
                                        /* 16 byte page write mode using*/
                                        /* last 4 bits of the address   */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10   /* and takes up to 10 msec */

/*
 * Init Memory Controller:
 *
 * BR0/1 and OR0/1 (FLASH)
 */

#define FLASH_BASE0_PRELIM      0xFF800000      /* FLASH bank #0        */
#define FLASH_BASE1_PRELIM      0xFFC00000      /* FLASH bank #1        */

/*-----------------------------------------------------------------------
 * External Bus Controller (EBC) Setup
 */

/* Memory Bank 0 (Flash Bank 0) initialization                                  */
#define CONFIG_SYS_EBC_PB0AP            0x92015480
#define CONFIG_SYS_EBC_PB0CR            0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */

/* Memory Bank 1 (Flash Bank 1) initialization                                  */
#define CONFIG_SYS_EBC_PB1AP            0x92015480
#define CONFIG_SYS_EBC_PB1CR            0xFF85A000  /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */

/* Memory Bank 2 (CAN0, 1, 2, Codeswitch) initialization                        */
#define CONFIG_SYS_EBC_PB2AP            0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
#define CONFIG_SYS_EBC_PB2CR            0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */

/* Memory Bank 3 (CompactFlash IDE) initialization                              */
#define CONFIG_SYS_EBC_PB3AP            0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
#define CONFIG_SYS_EBC_PB3CR            0xF011A000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */

/* Memory Bank 4 (NVRAM) initialization                                         */
#define CONFIG_SYS_EBC_PB4AP            0x01005280  /* TWT=2,WBN=1,WBF=1,TH=1,SOR=1     */
#define CONFIG_SYS_EBC_PB4CR            0xF0218000  /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit  */

/* Memory Bank 5 (Quart) initialization                                         */
#define CONFIG_SYS_EBC_PB5AP            0x04005B80  /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/
#define CONFIG_SYS_EBC_PB5CR            0xF0318000  /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit  */

/*-----------------------------------------------------------------------
 * FPGA stuff
 */

/* FPGA program pin configuration */
#define CONFIG_SYS_FPGA_PRG             0x04000000  /* FPGA program pin (ppc output) */
#define CONFIG_SYS_FPGA_CLK             0x02000000  /* FPGA clk pin (ppc output)     */
#define CONFIG_SYS_FPGA_DATA            0x01000000  /* FPGA data pin (ppc output)    */
#define CONFIG_SYS_FPGA_INIT            0x00400000  /* FPGA init pin (ppc input)     */
#define CONFIG_SYS_FPGA_DONE            0x00800000  /* FPGA done pin (ppc input)     */

/*-----------------------------------------------------------------------
 * Definitions for initial stack pointer and data area (in data cache)
 */
#if 1 /* test-only */
#define CONFIG_SYS_INIT_DCACHE_CS       7       /* use cs # 7 for data cache memory    */

#define CONFIG_SYS_INIT_RAM_ADDR        0x40000000  /* use data cache                  */
#else
#define CONFIG_SYS_INIT_RAM_ADDR        0x00df0000 /* inside of SDRAM                   */
#endif
#define CONFIG_SYS_INIT_RAM_SIZE        0x2000  /* Size of used area in RAM            */
#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET

#endif  /* __CONFIG_H */