1/* 2 * U-boot - Configuration file for PR1 Appliance 3 * 4 * based on bf537-stamp.h 5 * Copyright (c) Switchfin Org. <dpn@switchfin.org> 6 */ 7 8#ifndef __CONFIG_PR1_H__ 9#define __CONFIG_PR1_H__ 10 11#include <asm/config-pre.h> 12 13 14/* 15 * Processor Settings 16 */ 17#define CONFIG_BFIN_CPU bf537-0.3 18#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_SPI_MASTER 19 20 21/* 22 * Clock Settings 23 * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV 24 * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV 25 */ 26/* CONFIG_CLKIN_HZ is any value in Hz */ 27#define CONFIG_CLKIN_HZ 25000000 28/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */ 29/* 1 = CLKIN / 2 */ 30#define CONFIG_CLKIN_HALF 0 31/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */ 32/* 1 = bypass PLL */ 33#define CONFIG_PLL_BYPASS 0 34/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */ 35/* Values can range from 0-63 (where 0 means 64) */ 36#define CONFIG_VCO_MULT 24 37/* CCLK_DIV controls the core clock divider */ 38/* Values can be 1, 2, 4, or 8 ONLY */ 39#define CONFIG_CCLK_DIV 1 40/* SCLK_DIV controls the system clock divider */ 41/* Values can range from 1-15 */ 42#define CONFIG_SCLK_DIV 5 43 44 45/* 46 * Memory Settings 47 */ 48#define CONFIG_MEM_ADD_WDTH 11 49#define CONFIG_MEM_SIZE 128 50 51#define CONFIG_EBIU_SDRRC_VAL 0x306 52#define CONFIG_EBIU_SDGCTL_VAL 0x8091998d 53 54#define CONFIG_EBIU_AMGCTL_VAL 0xFF 55#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0 56#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0 57 58#define CONFIG_SYS_MONITOR_LEN (512 * 1024) 59#define CONFIG_SYS_MALLOC_LEN (384 * 1024) 60 61 62/* 63 * Network Settings 64 */ 65#ifndef __ADSPBF534__ 66#define ADI_CMDS_NETWORK 1 67#define CONFIG_BFIN_MAC 68#define CONFIG_NETCONSOLE 69#endif 70#define CONFIG_HOSTNAME pr1 71#define CONFIG_TFTP_BLOCKSIZE 4404 72/* Uncomment next line to use fixed MAC address */ 73/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */ 74 75 76/* 77 * Flash Settings 78 */ 79#define CONFIG_SYS_NO_FLASH /* We have no parallel FLASH */ 80 81 82/* 83 * SPI Settings 84 */ 85#define CONFIG_BFIN_SPI 86#define CONFIG_ENV_SPI_MAX_HZ 30000000 87#define CONFIG_SF_DEFAULT_SPEED 30000000 88#define CONFIG_SPI_FLASH 89#define CONFIG_SPI_FLASH_STMICRO 90 91 92/* 93 * Env Storage Settings 94 */ 95#define CONFIG_ENV_IS_IN_SPI_FLASH 96#define CONFIG_ENV_OFFSET 0x10000 97#define CONFIG_ENV_SIZE 0x2000 98#define CONFIG_ENV_SECT_SIZE 0x10000 99#define CONFIG_ENV_IS_EMBEDDED_IN_LDR 100 101 102/* 103 * I2C Settings 104 */ 105#define CONFIG_BFIN_TWI_I2C 106#define CONFIG_HARD_I2C 107 108 109/* 110 * NAND Settings 111 */ 112#define CONFIG_NAND_PLAT 113#define CONFIG_SYS_NAND_BASE 0x20000000 114#define CONFIG_SYS_MAX_NAND_DEVICE 1 115 116#define BFIN_NAND_CLE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 2)) 117#define BFIN_NAND_ALE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 1)) 118#define BFIN_NAND_WRITE(addr, cmd) \ 119 do { \ 120 bfin_write8(addr, cmd); \ 121 SSYNC(); \ 122 } while (0) 123 124#define NAND_PLAT_WRITE_CMD(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_CLE(chip), cmd) 125#define NAND_PLAT_WRITE_ADR(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_ALE(chip), cmd) 126#define NAND_PLAT_GPIO_DEV_READY GPIO_PF9 127 128/* 129 * Misc Settings 130 */ 131#define CONFIG_BAUDRATE 115200 132#define CONFIG_RTC_BFIN 133#define CONFIG_UART_CONSOLE 0 134#define CONFIG_SYS_PROMPT "pr1>" 135#define CONFIG_BOOTCOMMAND "run nandboot" 136#define CONFIG_BOOTDELAY 2 137#define CONFIG_LOADADDR 0x2000000 138 139 140/* 141 * Pull in common ADI header for remaining command/environment setup 142 */ 143#include <configs/bfin_adi_common.h> 144 145/* 146 * Overwrite some settings defined in bfin_adi_common.h 147 */ 148#undef NAND_ENV_SETTINGS 149#define NAND_ENV_SETTINGS \ 150 "nandargs=set bootargs " CONFIG_BOOTARGS "\0" \ 151 "nandboot=" \ 152 "nand read $(loadaddr) 0x0 0x900000;" \ 153 "run nandargs;" \ 154 "bootm" \ 155 "\0" 156 157#endif 158