1/* 2 * (C) Copyright 2000-2005 3 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. 4 * 5 * See file CREDITS for list of people who contributed to this 6 * project. 7 * 8 * This program is free software; you can redistribute it and/or 9 * modify it under the terms of the GNU General Public License as 10 * published by the Free Software Foundation; either version 2 of 11 * the License, or (at your option) any later version. 12 * 13 * This program is distributed in the hope that it will be useful, 14 * but WITHOUT ANY WARRANTY; without even the implied warranty of 15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 16 * GNU General Public License for more details. 17 * 18 * You should have received a copy of the GNU General Public License 19 * along with this program; if not, write to the Free Software 20 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 21 * MA 02111-1307 USA 22 */ 23 24/* 25 * board/config.h - configuration options, board specific 26 */ 27 28#ifndef __CONFIG_H 29#define __CONFIG_H 30 31/* 32 * High Level Configuration Options 33 * (easy to change) 34 */ 35 36#define CONFIG_MPC860 1 /* This is a MPC860 CPU */ 37#define CONFIG_IP860 1 /* ...on a IP860 board */ 38 39#define CONFIG_SYS_TEXT_BASE 0x10000000 40 41#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ 42#define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */ 43 44#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ 45#define CONFIG_BAUDRATE 9600 46#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ 47 48#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo" \ 49"\0load=tftp \"/tftpboot/u-boot.bin\"\0update=protect off 1:0;era 1:0;cp.b 100000 10000000 ${filesize}\0" 50 51#undef CONFIG_BOOTARGS 52#define CONFIG_BOOTCOMMAND \ 53 "bootp; " \ 54 "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ 55 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \ 56 "bootm" 57 58#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 59#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ 60 61#undef CONFIG_WATCHDOG /* watchdog disabled */ 62 63 64/* enable I2C and select the hardware/software driver */ 65#undef CONFIG_HARD_I2C /* I2C with hardware support */ 66#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ 67/* 68 * Software (bit-bang) I2C driver configuration 69 */ 70#define PB_SCL 0x00000020 /* PB 26 */ 71#define PB_SDA 0x00000010 /* PB 27 */ 72 73#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) 74#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) 75#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) 76#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) 77#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \ 78 else immr->im_cpm.cp_pbdat &= ~PB_SDA 79#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ 80 else immr->im_cpm.cp_pbdat &= ~PB_SCL 81#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ 82 83 84# define CONFIG_SYS_I2C_SPEED 50000 85# define CONFIG_SYS_I2C_SLAVE 0xFE 86# define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM X24C16 */ 87# define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */ 88/* mask of address bits that overflow into the "EEPROM chip address" */ 89#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 90#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 91#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* takes up to 10 msec */ 92 93#define CONFIG_TIMESTAMP /* Print image info with timestamp */ 94 95 96/* 97 * Command line configuration. 98 */ 99#include <config_cmd_default.h> 100 101#define CONFIG_CMD_BEDBUG 102#define CONFIG_CMD_I2C 103#define CONFIG_CMD_EEPROM 104#define CONFIG_CMD_NFS 105#define CONFIG_CMD_SNTP 106 107/* 108 * BOOTP options 109 */ 110#define CONFIG_BOOTP_SUBNETMASK 111#define CONFIG_BOOTP_GATEWAY 112#define CONFIG_BOOTP_HOSTNAME 113#define CONFIG_BOOTP_BOOTPATH 114 115/* 116 * Miscellaneous configurable options 117 */ 118#define CONFIG_SYS_LONGHELP /* undef to save memory */ 119#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 120#if defined(CONFIG_CMD_KGDB) 121#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 122#else 123#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 124#endif 125#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 126#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 127#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 128 129#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ 130#define CONFIG_SYS_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */ 131 132#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */ 133 134#define CONFIG_SYS_PIO_MODE 0 /* IDE interface in PIO Mode 0 */ 135 136#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ 137 138/* 139 * Low Level Configuration Settings 140 * (address mappings, register initial values, etc.) 141 * You should know what you are doing if you make changes here. 142 */ 143/*----------------------------------------------------------------------- 144 * Internal Memory Mapped Register 145 */ 146#define CONFIG_SYS_IMMR 0xF1000000 /* Non-standard value!! */ 147 148/*----------------------------------------------------------------------- 149 * Definitions for initial stack pointer and data area (in DPRAM) 150 */ 151#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR 152#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ 153#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 154#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 155 156/*----------------------------------------------------------------------- 157 * Start addresses for the final memory configuration 158 * (Set up by the startup code) 159 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 160 */ 161#define CONFIG_SYS_SDRAM_BASE 0x00000000 162#define CONFIG_SYS_FLASH_BASE 0x10000000 163#ifdef DEBUG 164#define CONFIG_SYS_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */ 165#else 166#if 0 /* need more space for I2C tests */ 167#define CONFIG_SYS_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */ 168#else 169#define CONFIG_SYS_MONITOR_LEN (256 << 10) 170#endif 171#endif 172#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE 173#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ 174 175/* 176 * For booting Linux, the board info and command line data 177 * have to be in the first 8 MB of memory, since this is 178 * the maximum mapped by the Linux kernel during initialization. 179 */ 180#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ 181/*----------------------------------------------------------------------- 182 * FLASH organization 183 */ 184#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ 185#define CONFIG_SYS_MAX_FLASH_SECT 124 /* max number of sectors on one chip */ 186 187#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ 188#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ 189 190#undef CONFIG_ENV_IS_IN_FLASH 191#undef CONFIG_ENV_IS_IN_NVRAM 192#undef CONFIG_ENV_IS_IN_NVRAM 193#undef DEBUG_I2C 194#define CONFIG_ENV_IS_IN_EEPROM 195 196#ifdef CONFIG_ENV_IS_IN_NVRAM 197#define CONFIG_ENV_ADDR 0x20000000 /* use SRAM */ 198#define CONFIG_ENV_SIZE (16<<10) /* use 16 kB */ 199#endif /* CONFIG_ENV_IS_IN_NVRAM */ 200 201#ifdef CONFIG_ENV_IS_IN_EEPROM 202#define CONFIG_ENV_OFFSET 512 /* Leave 512 bytes free for other data */ 203#define CONFIG_ENV_SIZE 1536 /* Use remaining space */ 204#endif /* CONFIG_ENV_IS_IN_EEPROM */ 205 206/*----------------------------------------------------------------------- 207 * Cache Configuration 208 */ 209#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ 210#if defined(CONFIG_CMD_KGDB) 211#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ 212#endif 213#define CONFIG_SYS_DELAYED_ICACHE 1 /* enable ICache not before 214 * running in RAM. 215 */ 216 217/*----------------------------------------------------------------------- 218 * SYPCR - System Protection Control 11-9 219 * SYPCR can only be written once after reset! 220 *----------------------------------------------------------------------- 221 * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze 222 * +0x0004 223 */ 224#if defined(CONFIG_WATCHDOG) 225#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ 226 SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) 227#else 228#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) 229#endif 230 231/*----------------------------------------------------------------------- 232 * SIUMCR - SIU Module Configuration 11-6 233 *----------------------------------------------------------------------- 234 * +0x0000 => 0x80600800 235 */ 236#define CONFIG_SYS_SIUMCR (SIUMCR_EARB | SIUMCR_EARP0 | \ 237 SIUMCR_DBGC11 | SIUMCR_MLRC10) 238 239/*----------------------------------------------------------------------- 240 * Clock Setting - get clock frequency from Board Revision Register 241 *----------------------------------------------------------------------- 242 */ 243#ifndef __ASSEMBLY__ 244extern unsigned long ip860_get_clk_freq (void); 245#endif 246#define CONFIG_8xx_GCLK_FREQ ip860_get_clk_freq() 247 248/*----------------------------------------------------------------------- 249 * TBSCR - Time Base Status and Control 11-26 250 *----------------------------------------------------------------------- 251 * Clear Reference Interrupt Status, Timebase freezing enabled 252 * +0x0200 => 0x00C2 253 */ 254#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) 255 256/*----------------------------------------------------------------------- 257 * PISCR - Periodic Interrupt Status and Control 11-31 258 *----------------------------------------------------------------------- 259 * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled 260 * +0x0240 => 0x0082 261 */ 262#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) 263 264/*----------------------------------------------------------------------- 265 * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 266 *----------------------------------------------------------------------- 267 * Reset PLL lock status sticky bit, timer expired status bit and timer 268 * interrupt status bit, set PLL multiplication factor ! 269 */ 270/* +0x0286 => was: 0x0000D000 */ 271#define CONFIG_SYS_PLPRCR \ 272 ( PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | \ 273 /*PLPRCR_CSRC|*/ PLPRCR_LPM_NORMAL | \ 274 PLPRCR_CSR | PLPRCR_LOLRE /*|PLPRCR_FIOPD*/ \ 275 ) 276 277/*----------------------------------------------------------------------- 278 * SCCR - System Clock and reset Control Register 15-27 279 *----------------------------------------------------------------------- 280 * Set clock output, timebase and RTC source and divider, 281 * power management and some other internal clocks 282 */ 283#define SCCR_MASK SCCR_EBDF11 284#define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_TBS | \ 285 SCCR_RTDIV | SCCR_RTSEL | \ 286 /*SCCR_CRQEN|*/ /*SCCR_PRQEN|*/ \ 287 SCCR_EBDF00 | SCCR_DFSYNC00 | \ 288 SCCR_DFBRG00 | SCCR_DFNL000 | \ 289 SCCR_DFNH000) 290 291/*----------------------------------------------------------------------- 292 * RTCSC - Real-Time Clock Status and Control Register 11-27 293 *----------------------------------------------------------------------- 294 */ 295/* +0x0220 => 0x00C3 */ 296#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) 297 298 299/*----------------------------------------------------------------------- 300 * RCCR - RISC Controller Configuration Register 19-4 301 *----------------------------------------------------------------------- 302 */ 303/* +0x09C4 => TIMEP=1 */ 304#define CONFIG_SYS_RCCR 0x0100 305 306/*----------------------------------------------------------------------- 307 * RMDS - RISC Microcode Development Support Control Register 308 *----------------------------------------------------------------------- 309 */ 310#define CONFIG_SYS_RMDS 0 311 312/*----------------------------------------------------------------------- 313 * DER - Debug Event Register 314 *----------------------------------------------------------------------- 315 * 316 */ 317#define CONFIG_SYS_DER 0 318 319/* 320 * Init Memory Controller: 321 */ 322 323/* 324 * MAMR settings for SDRAM - 16-14 325 * => 0xC3804114 326 */ 327 328/* periodic timer for refresh */ 329#define CONFIG_SYS_MAMR_PTA 0xC3 330 331#define CONFIG_SYS_MAMR ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ 332 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ 333 MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) 334/* 335 * BR1 and OR1 (FLASH) 336 */ 337#define FLASH_BASE 0x10000000 /* FLASH bank #0 */ 338 339/* used to re-map FLASH 340 * restrict access enough to keep SRAM working (if any) 341 * but not too much to meddle with FLASH accesses 342 */ 343/* allow for max 8 MB of Flash */ 344#define CONFIG_SYS_REMAP_OR_AM 0xFF800000 /* OR addr mask */ 345#define CONFIG_SYS_PRELIM_OR_AM 0xFF800000 /* OR addr mask */ 346 347#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | OR_SCY_6_CLK) 348 349#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) 350#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) 351/* 16 bit, bank valid */ 352#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE & BR_BA_MSK) | BR_PS_32 | BR_V ) 353 354#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM 355#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_BR0_PRELIM 356 357/* 358 * BR2/OR2 - SDRAM 359 */ 360#define SDRAM_BASE 0x00000000 /* SDRAM bank */ 361#define SDRAM_PRELIM_OR_AM 0xF8000000 /* map max. 128 MB */ 362#define SDRAM_TIMING 0x00000A00 /* SDRAM-Timing */ 363 364#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB SDRAM */ 365 366#define CONFIG_SYS_OR2 (SDRAM_PRELIM_OR_AM | SDRAM_TIMING ) 367#define CONFIG_SYS_BR2 ((SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V ) 368 369/* 370 * BR3/OR3 - SRAM (16 bit) 371 */ 372#define SRAM_BASE 0x20000000 373#define CONFIG_SYS_OR3 0xFFF00130 /* BI/SCY = 5/TRLX (internal) */ 374#define CONFIG_SYS_BR3 ((SRAM_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) 375#define SRAM_SIZE (1 + (~(CONFIG_SYS_OR3 & BR_BA_MSK))) 376#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR3 /* Make sure to map early */ 377#define CONFIG_SYS_BR3_PRELIM CONFIG_SYS_BR3 /* in case it's used for ENV */ 378#define CONFIG_SYS_SRAM_BASE SRAM_BASE 379#define CONFIG_SYS_SRAM_SIZE SRAM_SIZE 380 381/* 382 * BR4/OR4 - Board Control & Status (8 bit) 383 */ 384#define BCSR_BASE 0xFC000000 385#define CONFIG_SYS_OR4 0xFFFF0120 /* BI (internal) */ 386#define CONFIG_SYS_BR4 ((BCSR_BASE & BR_BA_MSK) | BR_PS_8 | BR_V) 387 388/* 389 * BR5/OR5 - IP Slot A/B (16 bit) 390 */ 391#define IP_SLOT_BASE 0x40000000 392#define CONFIG_SYS_OR5 0xFE00010C /* SETA/TRLX/BI/ SCY=0 (external) */ 393#define CONFIG_SYS_BR5 ((IP_SLOT_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) 394 395/* 396 * BR6/OR6 - VME STD (16 bit) 397 */ 398#define VME_STD_BASE 0xFE000000 399#define CONFIG_SYS_OR6 0xFF00010C /* SETA/TRLX/BI/SCY=0 (external) */ 400#define CONFIG_SYS_BR6 ((VME_STD_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) 401 402/* 403 * BR7/OR7 - SHORT I/O + RTC + IACK (16 bit) 404 */ 405#define VME_SHORT_BASE 0xFF000000 406#define CONFIG_SYS_OR7 0xFF00010C /* SETA/TRLX/BI/ SCY=0 (external) */ 407#define CONFIG_SYS_BR7 ((VME_SHORT_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) 408 409/*----------------------------------------------------------------------- 410 * Board Control and Status Region: 411 *----------------------------------------------------------------------- 412 */ 413#ifndef __ASSEMBLY__ 414typedef struct ip860_bcsr_s { 415 unsigned char shmem_addr; /* +00 shared memory address register */ 416 unsigned char reserved0; 417 unsigned char mbox_addr; /* +02 mailbox address register */ 418 unsigned char reserved1; 419 unsigned char vme_int_mask; /* +04 VME Bus interrupt mask register */ 420 unsigned char reserved2; 421 unsigned char vme_int_pend; /* +06 VME interrupt pending register */ 422 unsigned char reserved3; 423 unsigned char bd_int_mask; /* +08 board interrupt mask register */ 424 unsigned char reserved4; 425 unsigned char bd_int_pend; /* +0A board interrupt pending register */ 426 unsigned char reserved5; 427 unsigned char bd_ctrl; /* +0C board control register */ 428 unsigned char reserved6; 429 unsigned char bd_status; /* +0E board status register */ 430 unsigned char reserved7; 431 unsigned char vme_irq; /* +10 VME interrupt request register */ 432 unsigned char reserved8; 433 unsigned char vme_ivec; /* +12 VME interrupt vector register */ 434 unsigned char reserved9; 435 unsigned char cli_mbox; /* +14 clear mailbox irq */ 436 unsigned char reservedA; 437 unsigned char rtc; /* +16 RTC control register */ 438 unsigned char reservedB; 439 unsigned char mbox_data; /* +18 mailbox read/write register */ 440 unsigned char reservedC; 441 unsigned char wd_trigger; /* +1A Watchdog trigger register */ 442 unsigned char reservedD; 443 unsigned char rmw_req; /* +1C RMW request register */ 444 unsigned char reservedE; 445 unsigned char bd_rev; /* +1E Board Revision register */ 446} ip860_bcsr_t; 447#endif /* __ASSEMBLY__ */ 448 449/*----------------------------------------------------------------------- 450 * Board Control Register: bd_ctrl (Offset 0x0C) 451 *----------------------------------------------------------------------- 452 */ 453#define BD_CTRL_IPLSE 0x80 /* IP Slot Long Select Enable */ 454#define BD_CTRL_WDOGE 0x40 /* Watchdog Enable */ 455#define BD_CTRL_FLWE 0x20 /* Flash Write Enable */ 456#define BD_CTRL_RWDN 0x10 /* VMEBus Requester Release When Done Enable */ 457 458#endif /* __CONFIG_H */ 459