/*
 * (C) Copyright 2009 Wolfgang Denk <wd@denx.de>
 * (C) Copyright 2010 DAVE Srl <www.dave.eu>
 *
 * See file CREDITS for list of people who contributed to this
 * project.
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 */

/*
 * ifm AC14xx (MPC5121e based) board configuration file
 */

#ifndef __CONFIG_H
#define __CONFIG_H

#define CONFIG_AC14XX 1
/*
 * Memory map for the ifm AC14xx board:
 *
 * 0x0000_0000-0x0FFF_FFFF      DDR RAM (256 MB)
 * 0x3000_0000-0x3001_FFFF      On Chip SRAM (128 KB)
 * 0x8000_0000-0x803F_FFFF      IMMR (4 MB)
 * 0xE000_0000-0xEFFF_FFFF      several LPB attached hardware (CSx)
 * 0xFC00_0000-0xFFFF_FFFF      NOR Boot FLASH (64 MB)
 */

/*
 * High Level Configuration Options
 */
#define CONFIG_E300             1       /* E300 Family */
#define CONFIG_MPC512X          1       /* MPC512X family */

#define CONFIG_SYS_TEXT_BASE    0xFFF00000

#if defined(CONFIG_VIDEO)
#define CONFIG_CFB_CONSOLE
#define CONFIG_VGA_AS_SINGLE_DEVICE
#endif

#define CONFIG_SYS_MPC512X_CLKIN        25000000        /* in Hz */
#define SCFR1_IPS_DIV                   2
#define SCFR1_LPC_DIV                   2
#define SCFR1_NFC_DIV                   2
#define SCFR1_DIU_DIV                   240

#define CONFIG_MISC_INIT_R

#define CONFIG_SYS_IMMR                 0x80000000
#define CONFIG_SYS_DIU_ADDR             (CONFIG_SYS_IMMR + 0x2100)

/* more aggressive 'mtest' over a wider address range */
#define CONFIG_SYS_ALT_MEMTEST
#define CONFIG_SYS_MEMTEST_START        0x00100000      /* memtest region */
#define CONFIG_SYS_MEMTEST_END          0x0FE00000

/*
 * DDR Setup - manually set all parameters as there's no SPD etc.
 */
#define CONFIG_SYS_DDR_SIZE             256             /* MB */
#define CONFIG_SYS_DDR_BASE             0x00000000
#define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_MAX_RAM_SIZE         0x20000000

/*
 * DDR Controller Configuration
 *
 * SYS_CFG:
 *      [31:31] MDDRC Soft Reset:       Diabled
 *      [30:30] DRAM CKE pin:           Enabled
 *      [29:29] DRAM CLK:               Enabled
 *      [28:28] Command Mode:           Enabled (For initialization only)
 *      [27:25] DRAM Row Select:        dram_row[15:0] = magenta_address[25:10]
 *      [24:21] DRAM Bank Select:       dram_bank[1:0] = magenta_address[11:10]
 *      [20:19] Read Test:              DON'T USE
 *      [18:18] Self Refresh:           Enabled
 *      [17:17] 16bit Mode:             Disabled
 *      [16:13] Ready Delay:            2
 *      [12:12] Half DQS Delay:         Disabled
 *      [11:11] Quarter DQS Delay:      Disabled
 *      [10:08] Write Delay:            2
 *      [07:07] Early ODT:              Disabled
 *      [06:06] On DIE Termination:     Disabled
 *      [05:05] FIFO Overflow Clear:    DON'T USE here
 *      [04:04] FIFO Underflow Clear:   DON'T USE here
 *      [03:03] FIFO Overflow Pending:  DON'T USE here
 *      [02:02] FIFO Underlfow Pending: DON'T USE here
 *      [01:01] FIFO Overlfow Enabled:  Enabled
 *      [00:00] FIFO Underflow Enabled: Enabled
 * TIME_CFG0
 *      [31:16] DRAM Refresh Time:      0 CSB clocks
 *      [15:8]  DRAM Command Time:      0 CSB clocks
 *      [07:00] DRAM Precharge Time:    0 CSB clocks
 * TIME_CFG1
 *      [31:26] DRAM tRFC:
 *      [25:21] DRAM tWR1:
 *      [20:17] DRAM tWRT1:
 *      [16:11] DRAM tDRR:
 *      [10:05] DRAM tRC:
 *      [04:00] DRAM tRAS:
 * TIME_CFG2
 *      [31:28] DRAM tRCD:
 *      [27:23] DRAM tFAW:
 *      [22:19] DRAM tRTW1:
 *      [18:15] DRAM tCCD:
 *      [14:10] DRAM tRTP:
 *      [09:05] DRAM tRP:
 *      [04:00] DRAM tRPA
 */

/*
 * NOTE: although this board uses DDR1 only, the common source brings defaults
 * for DDR2 init sequences, that's why we have to keep those here as well
 */

/* DDR1 -- 32bit, drive strength (pad configuration) 3 for control and data */
#define CONFIG_SYS_IOCTRL_MUX_DDR       ((0 << 6) | (3 << 3) | (3 << 0))

#define CONFIG_SYS_MDDRC_SYS_CFG (/* 0xEAA09100 */ 0 \
                        | (1 << 31)     /* RST_B */ \
                        | (1 << 30)     /* CKE */ \
                        | (1 << 29)     /* CLK_ON */ \
                        | (0 << 28)     /* CMD_MODE */ \
                        | (5 << 25)     /* DRAM_ROW_SELECT */ \
                        | (5 << 21)     /* DRAM_BANK_SELECT */ \
                        | (0 << 18)     /* SELF_REF_EN */ \
                        | (0 << 17)     /* 16BIT_MODE */ \
                        | (4 << 13)     /* RDLY */ \
                        | (1 << 12)     /* HALF_DQS_DLY */ \
                        | (0 << 11)     /* QUART_DQS_DLY */ \
                        | (1 <<  8)     /* WDLY */ \
                        | (0 <<  7)     /* EARLY_ODT */ \
                        | (0 <<  6)     /* ON_DIE_TERMINATE */ \
                        | (0 <<  5)     /* FIFO_OV_CLEAR */ \
                        | (0 <<  4)     /* FIFO_UV_CLEAR */ \
                        | (0 <<  1)     /* FIFO_OV_EN */ \
                        | (0 <<  0)     /* FIFO_UV_EN */ \
                        )

#define CONFIG_SYS_MDDRC_TIME_CFG0      0x04E03124
#define CONFIG_SYS_MDDRC_TIME_CFG1      0x30CA1147
#define CONFIG_SYS_MDDRC_TIME_CFG2      0x32B10864

/* register address only, i.e. template without values */
#define CONFIG_SYS_MICRON_BMODE         0x01000000
#define CONFIG_SYS_MICRON_EMODE         0x01010000
#define CONFIG_SYS_MICRON_EMODE2        0x01020000
#define CONFIG_SYS_MICRON_EMODE3        0x01030000
/*
 * values for mode registers (without mode register address)
 */
/* CAS 2.5 (6), burst seq (0) and length 4 (2) */
#define CONFIG_SYS_MICRON_BMODE_PARAM   0x00000062
#define CONFIG_SYS_MICRON_BMODE_RSTDLL  0x00000100
/* DLL enable, reduced drive strength */
#define CONFIG_SYS_MICRON_EMODE_PARAM   0x00000002

#define CONFIG_SYS_DDRCMD_NOP           0x01380000
#define CONFIG_SYS_DDRCMD_PCHG_ALL      0x01100400
#define CONFIG_SYS_MICRON_EMR          ((1 << 24) |     /* CMD_REQ */ \
                                        (0 << 22) |     /* DRAM_CS */ \
                                        (0 << 21) |     /* DRAM_RAS */ \
                                        (0 << 20) |     /* DRAM_CAS */ \
                                        (0 << 19) |     /* DRAM_WEB */ \
                                        (1 << 16) |     /* DRAM_BS[2:0] */ \
                                        (0 << 15) |     /* */ \
                                        (0 << 12) |     /* A12->out */ \
                                        (0 << 11) |     /* A11->RDQS */ \
                                        (0 << 10) |     /* A10->DQS# */ \
                                        (0 <<  7) |     /* OCD program */ \
                                        (0 <<  6) |     /* Rtt1 */ \
                                        (0 <<  3) |     /* posted CAS# */ \
                                        (0 <<  2) |     /* Rtt0 */ \
                                        (1 <<  1) |     /* ODS */ \
                                        (0 <<  0)       /* DLL */ \
                                     )
#define CONFIG_SYS_MICRON_EMR2          0x01020000
#define CONFIG_SYS_MICRON_EMR3          0x01030000
#define CONFIG_SYS_DDRCMD_RFSH          0x01080000
#define CONFIG_SYS_MICRON_INIT_DEV_OP   0x01000432
#define CONFIG_SYS_MICRON_EMR_OCD      ((1 << 24) |     /* CMD_REQ */ \
                                        (0 << 22) |     /* DRAM_CS */ \
                                        (0 << 21) |     /* DRAM_RAS */ \
                                        (0 << 20) |     /* DRAM_CAS */ \
                                        (0 << 19) |     /* DRAM_WEB */ \
                                        (1 << 16) |     /* DRAM_BS[2:0] */ \
                                        (0 << 15) |     /* */ \
                                        (0 << 12) |     /* A12->out */ \
                                        (0 << 11) |     /* A11->RDQS */ \
                                        (1 << 10) |     /* A10->DQS# */ \
                                        (7 <<  7) |     /* OCD program */ \
                                        (0 <<  6) |     /* Rtt1 */ \
                                        (0 <<  3) |     /* posted CAS# */ \
                                        (1 <<  2) |     /* Rtt0 */ \
                                        (0 <<  1) |     /* ODS */ \
                                        (0 <<  0)       /* DLL */ \
                                     )

/*
 * Backward compatible definitions,
 * so we do not have to change arch/powerpc/cpu/mpc512x/fixed_sdram.c
 */
#define CONFIG_SYS_DDRCMD_EM2           (CONFIG_SYS_MICRON_EMR2)
#define CONFIG_SYS_DDRCMD_EM3           (CONFIG_SYS_MICRON_EMR3)
#define CONFIG_SYS_DDRCMD_EN_DLL        (CONFIG_SYS_MICRON_EMR)
#define CONFIG_SYS_DDRCMD_OCD_DEFAULT   (CONFIG_SYS_MICRON_EMR_OCD)

/* DDR Priority Manager Configuration */
#define CONFIG_SYS_MDDRCGRP_PM_CFG1     0x00077777
#define CONFIG_SYS_MDDRCGRP_PM_CFG2     0x00000000
#define CONFIG_SYS_MDDRCGRP_HIPRIO_CFG  0x00000001
#define CONFIG_SYS_MDDRCGRP_LUT0_MU     0xFFEEDDCC
#define CONFIG_SYS_MDDRCGRP_LUT0_ML     0xBBAAAAAA
#define CONFIG_SYS_MDDRCGRP_LUT1_MU     0x66666666
#define CONFIG_SYS_MDDRCGRP_LUT1_ML     0x55555555
#define CONFIG_SYS_MDDRCGRP_LUT2_MU     0x44444444
#define CONFIG_SYS_MDDRCGRP_LUT2_ML     0x44444444
#define CONFIG_SYS_MDDRCGRP_LUT3_MU     0x55555555
#define CONFIG_SYS_MDDRCGRP_LUT3_ML     0x55555558
#define CONFIG_SYS_MDDRCGRP_LUT4_MU     0x11111111
#define CONFIG_SYS_MDDRCGRP_LUT4_ML     0x11111122
#define CONFIG_SYS_MDDRCGRP_LUT0_AU     0xaaaaaaaa
#define CONFIG_SYS_MDDRCGRP_LUT0_AL     0xaaaaaaaa
#define CONFIG_SYS_MDDRCGRP_LUT1_AU     0x66666666
#define CONFIG_SYS_MDDRCGRP_LUT1_AL     0x66666666
#define CONFIG_SYS_MDDRCGRP_LUT2_AU     0x11111111
#define CONFIG_SYS_MDDRCGRP_LUT2_AL     0x11111111
#define CONFIG_SYS_MDDRCGRP_LUT3_AU     0x11111111
#define CONFIG_SYS_MDDRCGRP_LUT3_AL     0x11111111
#define CONFIG_SYS_MDDRCGRP_LUT4_AU     0x11111111
#define CONFIG_SYS_MDDRCGRP_LUT4_AL     0x11111111

/*
 * NOR FLASH on the Local Bus
 */
#define CONFIG_SYS_FLASH_CFI                            /* use the CFI code */
#define CONFIG_FLASH_CFI_DRIVER                         /* use the CFI driver */
#define CONFIG_SYS_FLASH_BASE           0xFC000000      /* start of FLASH */
#define CONFIG_SYS_FLASH_SIZE           0x04000000      /* max flash size */

#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#define CONFIG_SYS_MAX_FLASH_BANKS      1               /* number of banks */
#define CONFIG_SYS_FLASH_BANKS_LIST     { \
        CONFIG_SYS_FLASH_BASE + 0 * CONFIG_SYS_FLASH_SIZE, \
        }
#define CONFIG_SYS_MAX_FLASH_SECT       512     /* max sectors per device */

#undef CONFIG_SYS_FLASH_CHECKSUM
#define CONFIG_SYS_FLASH_PROTECTION

/*
 * SRAM support
 */
#define CONFIG_SYS_SRAM_BASE            0x30000000
#define CONFIG_SYS_SRAM_SIZE            0x00020000      /* 128 KB */

/*
 * CS related parameters
 */
/* CS0 Flash */
#define CONFIG_SYS_CS0_CFG              0x00031110
#define CONFIG_SYS_CS0_START            0xFC000000
#define CONFIG_SYS_CS0_SIZE             0x04000000
/* CS1 FRAM */
#define CONFIG_SYS_CS1_CFG              0x00011000
#define CONFIG_SYS_CS1_START            0xE0000000
#define CONFIG_SYS_CS1_SIZE             0x00010000
/* CS2 AS-i 1 */
#define CONFIG_SYS_CS2_CFG              0x00009100
#define CONFIG_SYS_CS2_START            0xE0100000
#define CONFIG_SYS_CS2_SIZE             0x00080000
/* CS3 netX */
#define CONFIG_SYS_CS3_CFG              0x000A1140
#define CONFIG_SYS_CS3_START            0xE0300000
#define CONFIG_SYS_CS3_SIZE             0x00020000
/* CS5 safety */
#define CONFIG_SYS_CS5_CFG              0x0011F000
#define CONFIG_SYS_CS5_START            0xE0400000
#define CONFIG_SYS_CS5_SIZE             0x00010000
/* CS6 AS-i 2 */
#define CONFIG_SYS_CS6_CFG              0x00009100
#define CONFIG_SYS_CS6_START            0xE0200000
#define CONFIG_SYS_CS6_SIZE             0x00080000

/* Don't use alternative CS timing for any CS */
#define CONFIG_SYS_CS_ALETIMING         0x00000000
#define CONFIG_SYS_CS_BURST             0x00000000
#define CONFIG_SYS_CS_DEADCYCLE         0x00000020
#define CONFIG_SYS_CS_HOLDCYCLE         0x00000020

/* Use SRAM for initial stack */
#define CONFIG_SYS_INIT_RAM_ADDR        CONFIG_SYS_SRAM_BASE
#define CONFIG_SYS_INIT_RAM_END         CONFIG_SYS_SRAM_SIZE

#define CONFIG_SYS_GBL_DATA_SIZE        0x100
#define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_END - \
                                         CONFIG_SYS_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET

#define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_MONITOR_LEN          (256 * 1024)

#ifdef  CONFIG_FSL_DIU_FB
#define CONFIG_SYS_MALLOC_LEN           (6 * 1024 * 1024)
#else
#define CONFIG_SYS_MALLOC_LEN           (512 * 1024)
#endif

/*
 * Serial Port
 */
#define CONFIG_CONS_INDEX               1

/*
 * Serial console configuration
 */
#define CONFIG_PSC_CONSOLE              3       /* console on PSC3 */
#define CONFIG_SYS_PSC3
#if CONFIG_PSC_CONSOLE != 3
#error CONFIG_PSC_CONSOLE must be 3
#endif

#define CONFIG_BAUDRATE                 115200  /* ... at 115200 bps */

#define CONSOLE_FIFO_TX_SIZE            FIFOC_PSC3_TX_SIZE
#define CONSOLE_FIFO_TX_ADDR            FIFOC_PSC3_TX_ADDR
#define CONSOLE_FIFO_RX_SIZE            FIFOC_PSC3_RX_SIZE
#define CONSOLE_FIFO_RX_ADDR            FIFOC_PSC3_RX_ADDR

/*
 * Clocks in use
 */
#define SCCR1_CLOCKS_EN (CLOCK_SCCR1_CFG_EN |           \
                         CLOCK_SCCR1_LPC_EN |           \
                         CLOCK_SCCR1_PSC_EN(CONFIG_PSC_CONSOLE) | \
                         CLOCK_SCCR1_PSC_EN(7) |        \
                         CLOCK_SCCR1_PSCFIFO_EN |       \
                         CLOCK_SCCR1_DDR_EN |           \
                         CLOCK_SCCR1_FEC_EN |           \
                         CLOCK_SCCR1_TPR_EN)

#define SCCR2_CLOCKS_EN (CLOCK_SCCR2_MEM_EN |           \
                         CLOCK_SCCR2_SPDIF_EN |         \
                         CLOCK_SCCR2_DIU_EN |           \
                         CLOCK_SCCR2_I2C_EN)


#define CONFIG_CMDLINE_EDITING          1       /* command line history */

/* I2C */
#define CONFIG_HARD_I2C                 /* I2C with hardware support */
#define CONFIG_I2C_MULTI_BUS

/* I2C speed and slave address */
#define CONFIG_SYS_I2C_SPEED            100000
#define CONFIG_SYS_I2C_SLAVE            0x7F

/*
 * IIM - IC Identification Module
 */
#undef CONFIG_FSL_IIM

/*
 * EEPROM configuration for Atmel AT24C01:
 * 8-bit addresses, 30ms write delay, 32-Byte Page Write Mode
 */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          1
#define CONFIG_SYS_I2C_EEPROM_ADDR              0x52
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   30
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       5

/*
 * Ethernet configuration
 */
#define CONFIG_MPC512x_FEC              1
#define CONFIG_NET_MULTI
#define CONFIG_PHY_ADDR                 0x1F
#define CONFIG_MII                      1       /* MII PHY management */
#define CONFIG_FEC_AN_TIMEOUT           1
#define CONFIG_HAS_ETH0

/*
 * Environment
 */
#define CONFIG_ENV_IS_IN_FLASH          1
/* This has to be a multiple of the flash sector size */
#define CONFIG_ENV_ADDR                 0xFFF40000
#define CONFIG_ENV_SIZE                 0x2000
#define CONFIG_ENV_SECT_SIZE            0x20000

/* Address and size of Redundant Environment Sector */
#define CONFIG_ENV_ADDR_REDUND          (CONFIG_ENV_ADDR + \
                                         CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND          (CONFIG_ENV_SIZE)

#define CONFIG_LOADS_ECHO               1
#define CONFIG_SYS_LOADS_BAUD_CHANGE    1

#include <config_cmd_default.h>

#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_EEPROM
#undef CONFIG_CMD_FUSE
#define CONFIG_CMD_I2C
#undef CONFIG_CMD_IDE
#undef CONFIG_CMD_EXT2
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_MII
#define CONFIG_CMD_NFS
#define CONFIG_CMD_PING
#define CONFIG_CMD_REGINFO

#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
#endif

#if defined(CONFIG_CMD_IDE) || defined(CONFIG_CMD_EXT2)
#define CONFIG_DOS_PARTITION
#define CONFIG_MAC_PARTITION
#define CONFIG_ISO_PARTITION
#endif /* defined(CONFIG_CMD_IDE) */

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP                     /* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
#define CONFIG_SYS_PROMPT       "ac14xx> "      /* Monitor Command Prompt */

#ifdef CONFIG_CMD_KGDB
# define CONFIG_SYS_CBSIZE      1024            /* Console I/O Buffer Size */
#else
# define CONFIG_SYS_CBSIZE      256             /* Console I/O Buffer Size */
#endif

/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE       (CONFIG_SYS_CBSIZE + \
                                 sizeof(CONFIG_SYS_PROMPT) + 16)
/* max number of command args */
#define CONFIG_SYS_MAXARGS      32
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE

/* decrementer freq: 1ms ticks */
#define CONFIG_SYS_HZ           1000

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ            (8 << 20)

/* Cache Configuration */
#define CONFIG_SYS_DCACHE_SIZE          32768
#define CONFIG_SYS_CACHELINE_SIZE       32
#ifdef CONFIG_CMD_KGDB
#define CONFIG_SYS_CACHELINE_SHIFT      5       /* log base 2 of 32 */
#endif

#define CONFIG_SYS_HID0_INIT            0x000000000
#define CONFIG_SYS_HID0_FINAL           (HID0_ENABLE_MACHINE_CHECK | \
                                         HID0_ICE)
#define CONFIG_SYS_HID2 HID2_HBE

#define CONFIG_HIGH_BATS                1       /* High BATs supported */

/*
 * Internal Definitions
 *
 * Boot Flags
 */
#define BOOTFLAG_COLD                   0x01
#define BOOTFLAG_WARM                   0x02

#ifdef CONFIG_CMD_KGDB
#define CONFIG_KGDB_BAUDRATE            230400  /* speed of kgdb serial port */
#define CONFIG_KGDB_SER_INDEX           2       /* which serial port to use */
#endif

/*
 * Environment Configuration
 */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_TIMESTAMP

/* default load addr for tftp and bootm */
#define CONFIG_LOADADDR         400000

#define CONFIG_BOOTDELAY        2       /* -1 disables auto-boot */

/* the builtin environment and standard greeting */
#define CONFIG_PREBOOT  "echo;" \
        "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
        "echo"

#define CONFIG_EXTRA_ENV_SETTINGS_DEVEL                                 \
        "muster_nr=-00\0"                                               \
        "fromram=run ramargs addip addtty; "                            \
                "tftp ${fdt_addr_r} ac14xx/ac14xx.dtb${muster_nr}; "    \
                "tftp ${kernel_addr_r} ac14xx/uImage${muster_nr}; "     \
                "tftp ${ramdisk_addr_r} ac14xx/uFS${muster_nr}; "       \
                "bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr_r}\0" \
        "fromnfs=run nfsargs addip addtty; "                            \
                "tftp ${fdt_addr_r} ac14xx/ac14xx.dtb${muster_nr}; "    \
                "tftp ${kernel_addr_r} ac14xx/uImage${muster_nr}; "     \
                "bootm ${kernel_addr_r} - ${fdt_addr_r}\0"              \
        "fromflash=run nfsargs addip addtty; "                          \
                "bootm fc020000 - fc000000\0"                           \
        "mtdargsrec=setenv bootargs root=/dev/mtdblock1 ro\0"           \
        "recovery=run mtdargsrec addip addtty; "                        \
                "bootm ffd20000 - ffee0000\0"                           \
        "production=run ramargs addip addtty; "                         \
                "bootm fc020000 fc400000 fc000000\0"                    \
        "mtdargs=setenv bootargs root=/dev/mtdblock1 ro\0"              \
        "prodmtd=run mtdargs addip addtty; "                            \
                "bootm fc020000 - fc000000\0"                           \
        ""

#define CONFIG_EXTRA_ENV_SETTINGS                                       \
        "u-boot_addr_r=200000\0"                                        \
        "kernel_addr_r=600000\0"                                        \
        "fdt_addr_r=a00000\0"                                           \
        "ramdisk_addr_r=b00000\0"                                       \
        "u-boot_addr=FFF00000\0"                                        \
        "kernel_addr=FC020000\0"                                        \
        "fdt_addr=FC000000\0"                                           \
        "ramdisk_addr=FC400000\0"                                       \
        "verify=n\0"                                                    \
        "ramdiskfile=ac14xx/uRamdisk\0"                                 \
        "u-boot=ac14xx/u-boot.bin\0"                                    \
        "bootfile=ac14xx/uImage\0"                                      \
        "fdtfile=ac14xx/ac14xx.dtb\0"                                   \
        "netdev=eth0\0"                                                 \
        "consdev=ttyPSC0\0"                                             \
        "hostname=ac14xx\0"                                             \
        "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
                "nfsroot=${serverip}:${rootpath}${muster_nr}\0" \
        "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
        "addip=setenv bootargs ${bootargs} "                            \
                "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
                ":${hostname}:${netdev}:off panic=1\0"                  \
        "addtty=setenv bootargs ${bootargs} "                           \
                "console=${consdev},${baudrate}\0"                      \
        "flash_nfs=run nfsargs addip addtty;"                           \
                "bootm ${kernel_addr} - ${fdt_addr}\0"                  \
        "flash_self=run ramargs addip addtty;"                          \
                "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"    \
        "net_nfs=tftp ${kernel_addr_r} ${bootfile};"                    \
                "tftp ${fdt_addr_r} ${fdtfile};"                        \
                "run nfsargs addip addtty;"                             \
                "bootm ${kernel_addr_r} - ${fdt_addr_r}\0"              \
        "net_self=tftp ${kernel_addr_r} ${bootfile};"                   \
                "tftp ${ramdisk_addr_r} ${ramdiskfile};"                \
                "tftp ${fdt_addr_r} ${fdtfile};"                        \
                "run ramargs addip addtty;"                             \
                "bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr_r}\0"\
        "load=tftp ${u-boot_addr_r} ${u-boot}\0"                        \
        "update=protect off ${u-boot_addr} +${filesize};"               \
                "era ${u-boot_addr} +${filesize};"                      \
                "cp.b ${u-boot_addr_r} ${u-boot_addr} ${filesize}\0"    \
        CONFIG_EXTRA_ENV_SETTINGS_DEVEL                                 \
        "upd=run load update\0"                                         \
        ""

#define CONFIG_BOOTCOMMAND      "run production"

#define CONFIG_ARP_TIMEOUT      200UL

#define CONFIG_FIT              1
#define CONFIG_OF_LIBFDT        1
#define CONFIG_OF_BOARD_SETUP   1
#define CONFIG_OF_SUPPORT_OLD_DEVICE_TREES      1

#define OF_CPU                  "PowerPC,5121@0"
#define OF_SOC_COMPAT           "fsl,mpc5121-immr"
#define OF_TBCLK                (bd->bi_busfreq / 4)
#define OF_STDOUT_PATH          "/soc@80000000/serial@11300"

#endif  /* __CONFIG_H */