/*
 * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
 *
 * Based on da830evm.c. Original Copyrights follow:
 *
 * Copyright (C) 2009 Nick Thompson, GE Fanuc, Ltd. <nick.thompson@gefanuc.com>
 * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
 *
 * SPDX-License-Identifier:     GPL-2.0+
 */

#include <common.h>
#include <i2c.h>
#include <net.h>
#include <netdev.h>
#include <spi.h>
#include <spi_flash.h>
#include <asm/arch/hardware.h>
#include <asm/arch/emif_defs.h>
#include <asm/arch/emac_defs.h>
#include <asm/arch/pinmux_defs.h>
#include <asm/io.h>
#include <asm/arch/davinci_misc.h>
#include <asm/errno.h>
#include <hwconfig.h>

#ifdef CONFIG_DAVINCI_MMC
#include <mmc.h>
#include <asm/arch/sdmmc_defs.h>
#endif

DECLARE_GLOBAL_DATA_PTR;

#ifdef CONFIG_DRIVER_TI_EMAC
#ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII
#define HAS_RMII 1
#else
#define HAS_RMII 0
#endif
#endif /* CONFIG_DRIVER_TI_EMAC */

#define CFG_MAC_ADDR_SPI_BUS    0
#define CFG_MAC_ADDR_SPI_CS     0
#define CFG_MAC_ADDR_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
#define CFG_MAC_ADDR_SPI_MODE   SPI_MODE_3

#define CFG_MAC_ADDR_OFFSET     (flash->size - SZ_64K)

#ifdef CONFIG_MAC_ADDR_IN_SPIFLASH
static int get_mac_addr(u8 *addr)
{
        struct spi_flash *flash;
        int ret;

        flash = spi_flash_probe(CFG_MAC_ADDR_SPI_BUS, CFG_MAC_ADDR_SPI_CS,
                        CFG_MAC_ADDR_SPI_MAX_HZ, CFG_MAC_ADDR_SPI_MODE);
        if (!flash) {
                printf("Error - unable to probe SPI flash.\n");
                return -1;
        }

        ret = spi_flash_read(flash, CFG_MAC_ADDR_OFFSET, 6, addr);
        if (ret) {
                printf("Error - unable to read MAC address from SPI flash.\n");
                return -1;
        }

        return ret;
}
#endif

void dsp_lpsc_on(unsigned domain, unsigned int id)
{
        dv_reg_p mdstat, mdctl, ptstat, ptcmd;
        struct davinci_psc_regs *psc_regs;

        psc_regs = davinci_psc0_regs;
        mdstat = &psc_regs->psc0.mdstat[id];
        mdctl = &psc_regs->psc0.mdctl[id];
        ptstat = &psc_regs->ptstat;
        ptcmd = &psc_regs->ptcmd;

        while (*ptstat & (0x1 << domain))
                ;

        if ((*mdstat & 0x1f) == 0x03)
                return;                 /* Already on and enabled */

        *mdctl |= 0x03;

        *ptcmd = 0x1 << domain;

        while (*ptstat & (0x1 << domain))
                ;
        while ((*mdstat & 0x1f) != 0x03)
                ;               /* Probably an overkill... */
}

static void dspwake(void)
{
        unsigned *resetvect = (unsigned *)DAVINCI_L3CBARAM_BASE;
        u32 val;

        /* if the device is ARM only, return */
        if ((readl(CHIP_REV_ID_REG) & 0x3f) == 0x10)
                return;

        if (hwconfig_subarg_cmp_f("dsp", "wake", "no", NULL))
                return;

        *resetvect++ = 0x1E000; /* DSP Idle */
        /* clear out the next 10 words as NOP */
        memset(resetvect, 0, sizeof(unsigned) *10);

        /* setup the DSP reset vector */
        writel(DAVINCI_L3CBARAM_BASE, HOST1CFG);

        dsp_lpsc_on(1, DAVINCI_LPSC_GEM);
        val = readl(PSC0_MDCTL + (15 * 4));
        val |= 0x100;
        writel(val, (PSC0_MDCTL + (15 * 4)));
}

int misc_init_r(void)
{
        dspwake();

#if defined(CONFIG_MAC_ADDR_IN_SPIFLASH) || defined(CONFIG_MAC_ADDR_IN_EEPROM)

        uchar env_enetaddr[6];
        int enetaddr_found;

        enetaddr_found = eth_getenv_enetaddr("ethaddr", env_enetaddr);

#ifdef CONFIG_MAC_ADDR_IN_SPIFLASH
        int spi_mac_read;
        uchar buff[6];

        spi_mac_read = get_mac_addr(buff);

        /*
         * MAC address not present in the environment
         * try and read the MAC address from SPI flash
         * and set it.
         */
        if (!enetaddr_found) {
                if (!spi_mac_read) {
                        if (is_valid_ether_addr(buff)) {
                                if (eth_setenv_enetaddr("ethaddr", buff)) {
                                        printf("Warning: Failed to "
                                        "set MAC address from SPI flash\n");
                                }
                        } else {
                                        printf("Warning: Invalid "
                                        "MAC address read from SPI flash\n");
                        }
                }
        } else {
                /*
                 * MAC address present in environment compare it with
                 * the MAC address in SPI flash and warn on mismatch
                 */
                if (!spi_mac_read && is_valid_ether_addr(buff) &&
                                                memcmp(env_enetaddr, buff, 6))
                        printf("Warning: MAC address in SPI flash don't match "
                                        "with the MAC address in the environment\n");
                        printf("Default using MAC address from environment\n");
        }
#endif
        uint8_t enetaddr[8];
        int eeprom_mac_read;

        /* Read Ethernet MAC address from EEPROM */
        eeprom_mac_read = dvevm_read_mac_address(enetaddr);

        /*
         * MAC address not present in the environment
         * try and read the MAC address from EEPROM flash
         * and set it.
         */
        if (!enetaddr_found) {
                if (eeprom_mac_read)
                        /* Set Ethernet MAC address from EEPROM */
                        davinci_sync_env_enetaddr(enetaddr);
        } else {
                /*
                 * MAC address present in environment compare it with
                 * the MAC address in EEPROM and warn on mismatch
                 */
                if (eeprom_mac_read && memcmp(enetaddr, env_enetaddr, 6))
                        printf("Warning: MAC address in EEPROM don't match "
                                        "with the MAC address in the environment\n");
                        printf("Default using MAC address from environment\n");
        }

#endif
        return 0;
}

#ifdef CONFIG_DAVINCI_MMC
static struct davinci_mmc mmc_sd0 = {
        .reg_base = (struct davinci_mmc_regs *)DAVINCI_MMC_SD0_BASE,
        .host_caps = MMC_MODE_4BIT,     /* DA850 supports only 4-bit SD/MMC */
        .voltages = MMC_VDD_32_33 | MMC_VDD_33_34,
        .version = MMC_CTLR_VERSION_2,
};

int board_mmc_init(bd_t *bis)
{
        mmc_sd0.input_clk = clk_get(DAVINCI_MMCSD_CLKID);

        /* Add slot-0 to mmc subsystem */
        return davinci_mmc_init(bis, &mmc_sd0);
}
#endif

static const struct pinmux_config gpio_pins[] = {
#ifdef CONFIG_USE_NOR
        /* GP0[11] is required for NOR to work on Rev 3 EVMs */
        { pinmux(0), 8, 4 },    /* GP0[11] */
#endif
#ifdef CONFIG_DAVINCI_MMC
        /* GP0[11] is required for SD to work on Rev 3 EVMs */
        { pinmux(0),  8, 4 },   /* GP0[11] */
#endif
};

const struct pinmux_resource pinmuxes[] = {
#ifdef CONFIG_DRIVER_TI_EMAC
        PINMUX_ITEM(emac_pins_mdio),
#ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII
        PINMUX_ITEM(emac_pins_rmii),
#else
        PINMUX_ITEM(emac_pins_mii),
#endif
#endif
#ifdef CONFIG_SPI_FLASH
        PINMUX_ITEM(spi1_pins_base),
        PINMUX_ITEM(spi1_pins_scs0),
#endif
        PINMUX_ITEM(uart2_pins_txrx),
        PINMUX_ITEM(uart2_pins_rtscts),
        PINMUX_ITEM(i2c0_pins),
#ifdef CONFIG_NAND_DAVINCI
        PINMUX_ITEM(emifa_pins_cs3),
        PINMUX_ITEM(emifa_pins_cs4),
        PINMUX_ITEM(emifa_pins_nand),
#elif defined(CONFIG_USE_NOR)
        PINMUX_ITEM(emifa_pins_cs2),
        PINMUX_ITEM(emifa_pins_nor),
#endif
        PINMUX_ITEM(gpio_pins),
#ifdef CONFIG_DAVINCI_MMC
        PINMUX_ITEM(mmc0_pins),
#endif
};

const int pinmuxes_size = ARRAY_SIZE(pinmuxes);

const struct lpsc_resource lpsc[] = {
        { DAVINCI_LPSC_AEMIF }, /* NAND, NOR */
        { DAVINCI_LPSC_SPI1 },  /* Serial Flash */
        { DAVINCI_LPSC_EMAC },  /* image download */
        { DAVINCI_LPSC_UART2 }, /* console */
        { DAVINCI_LPSC_GPIO },
#ifdef CONFIG_DAVINCI_MMC
        { DAVINCI_LPSC_MMC_SD },
#endif
};

const int lpsc_size = ARRAY_SIZE(lpsc);

#ifndef CONFIG_DA850_EVM_MAX_CPU_CLK
#define CONFIG_DA850_EVM_MAX_CPU_CLK    300000000
#endif

#define REV_AM18X_EVM           0x100

/*
 * get_board_rev() - setup to pass kernel board revision information
 * Returns:
 * bit[0-3]     Maximum cpu clock rate supported by onboard SoC
 *              0000b - 300 MHz
 *              0001b - 372 MHz
 *              0010b - 408 MHz
 *              0011b - 456 MHz
 */
u32 get_board_rev(void)
{
        char *s;
        u32 maxcpuclk = CONFIG_DA850_EVM_MAX_CPU_CLK;
        u32 rev = 0;

        s = getenv("maxcpuclk");
        if (s)
                maxcpuclk = simple_strtoul(s, NULL, 10);

        if (maxcpuclk >= 456000000)
                rev = 3;
        else if (maxcpuclk >= 408000000)
                rev = 2;
        else if (maxcpuclk >= 372000000)
                rev = 1;
#ifdef CONFIG_DA850_AM18X_EVM
        rev |= REV_AM18X_EVM;
#endif
        return rev;
}

int board_early_init_f(void)
{
        /*
         * Power on required peripherals
         * ARM does not have access by default to PSC0 and PSC1
         * assuming here that the DSP bootloader has set the IOPU
         * such that PSC access is available to ARM
         */
        if (da8xx_configure_lpsc_items(lpsc, ARRAY_SIZE(lpsc)))
                return 1;

        return 0;
}

int board_init(void)
{
#ifndef CONFIG_USE_IRQ
        irq_init();
#endif

#ifdef CONFIG_NAND_DAVINCI
        /*
         * NAND CS setup - cycle counts based on da850evm NAND timings in the
         * Linux kernel @ 25MHz EMIFA
         */
        writel((DAVINCI_ABCR_WSETUP(2) |
                DAVINCI_ABCR_WSTROBE(2) |
                DAVINCI_ABCR_WHOLD(1) |
                DAVINCI_ABCR_RSETUP(1) |
                DAVINCI_ABCR_RSTROBE(4) |
                DAVINCI_ABCR_RHOLD(0) |
                DAVINCI_ABCR_TA(1) |
                DAVINCI_ABCR_ASIZE_8BIT),
               &davinci_emif_regs->ab2cr); /* CS3 */
#endif

        /* arch number of the board */
        gd->bd->bi_arch_number = MACH_TYPE_DAVINCI_DA850_EVM;

        /* address of boot parameters */
        gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;

        /* setup the SUSPSRC for ARM to control emulation suspend */
        writel(readl(&davinci_syscfg_regs->suspsrc) &
               ~(DAVINCI_SYSCFG_SUSPSRC_EMAC | DAVINCI_SYSCFG_SUSPSRC_I2C |
                 DAVINCI_SYSCFG_SUSPSRC_SPI1 | DAVINCI_SYSCFG_SUSPSRC_TIMER0 |
                 DAVINCI_SYSCFG_SUSPSRC_UART2),
               &davinci_syscfg_regs->suspsrc);

        /* configure pinmux settings */
        if (davinci_configure_pin_mux_items(pinmuxes, ARRAY_SIZE(pinmuxes)))
                return 1;

#ifdef CONFIG_USE_NOR
        /* Set the GPIO direction as output */
        clrbits_le32((u32 *)GPIO_BANK0_REG_DIR_ADDR, (0x01 << 11));

        /* Set the output as low */
        writel(0x01 << 11, GPIO_BANK0_REG_CLR_ADDR);
#endif

#ifdef CONFIG_DAVINCI_MMC
        /* Set the GPIO direction as output */
        clrbits_le32((u32 *)GPIO_BANK0_REG_DIR_ADDR, (0x01 << 11));

        /* Set the output as high */
        writel(0x01 << 11, GPIO_BANK0_REG_SET_ADDR);
#endif

#ifdef CONFIG_DRIVER_TI_EMAC
        davinci_emac_mii_mode_sel(HAS_RMII);
#endif /* CONFIG_DRIVER_TI_EMAC */

        /* enable the console UART */
        writel((DAVINCI_UART_PWREMU_MGMT_FREE | DAVINCI_UART_PWREMU_MGMT_URRST |
                DAVINCI_UART_PWREMU_MGMT_UTRST),
               &davinci_uart2_ctrl_regs->pwremu_mgmt);

        return 0;
}

#ifdef CONFIG_DRIVER_TI_EMAC

#ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII
/**
 * rmii_hw_init
 *
 * DA850/OMAP-L138 EVM can interface to a daughter card for
 * additional features. This card has an I2C GPIO Expander TCA6416
 * to select the required functions like camera, RMII Ethernet,
 * character LCD, video.
 *
 * Initialization of the expander involves configuring the
 * polarity and direction of the ports. P07-P05 are used here.
 * These ports are connected to a Mux chip which enables only one
 * functionality at a time.
 *
 * For RMII phy to respond, the MII MDIO clock has to be  disabled
 * since both the PHY devices have address as zero. The MII MDIO
 * clock is controlled via GPIO2[6].
 *
 * This code is valid for Beta version of the hardware
 */
int rmii_hw_init(void)
{
        const struct pinmux_config gpio_pins[] = {
                { pinmux(6), 8, 1 }
        };
        u_int8_t buf[2];
        unsigned int temp;
        int ret;

        /* PinMux for GPIO */
        if (davinci_configure_pin_mux(gpio_pins, ARRAY_SIZE(gpio_pins)) != 0)
                return 1;

        /* I2C Exapnder configuration */
        /* Set polarity to non-inverted */
        buf[0] = 0x0;
        buf[1] = 0x0;
        ret = i2c_write(CONFIG_SYS_I2C_EXPANDER_ADDR, 4, 1, buf, 2);
        if (ret) {
                printf("\nExpander @ 0x%02x write FAILED!!!\n",
                                CONFIG_SYS_I2C_EXPANDER_ADDR);
                return ret;
        }

        /* Configure P07-P05 as outputs */
        buf[0] = 0x1f;
        buf[1] = 0xff;
        ret = i2c_write(CONFIG_SYS_I2C_EXPANDER_ADDR, 6, 1, buf, 2);
        if (ret) {
                printf("\nExpander @ 0x%02x write FAILED!!!\n",
                                CONFIG_SYS_I2C_EXPANDER_ADDR);
        }

        /* For Ethernet RMII selection
         * P07(SelA)=0
         * P06(SelB)=1
         * P05(SelC)=1
         */
        if (i2c_read(CONFIG_SYS_I2C_EXPANDER_ADDR, 2, 1, buf, 1)) {
                printf("\nExpander @ 0x%02x read FAILED!!!\n",
                                CONFIG_SYS_I2C_EXPANDER_ADDR);
        }

        buf[0] &= 0x1f;
        buf[0] |= (0 << 7) | (1 << 6) | (1 << 5);
        if (i2c_write(CONFIG_SYS_I2C_EXPANDER_ADDR, 2, 1, buf, 1)) {
                printf("\nExpander @ 0x%02x write FAILED!!!\n",
                                CONFIG_SYS_I2C_EXPANDER_ADDR);
        }

        /* Set the output as high */
        temp = REG(GPIO_BANK2_REG_SET_ADDR);
        temp |= (0x01 << 6);
        REG(GPIO_BANK2_REG_SET_ADDR) = temp;

        /* Set the GPIO direction as output */
        temp = REG(GPIO_BANK2_REG_DIR_ADDR);
        temp &= ~(0x01 << 6);
        REG(GPIO_BANK2_REG_DIR_ADDR) = temp;

        return 0;
}
#endif /* CONFIG_DRIVER_TI_EMAC_USE_RMII */

/*
 * Initializes on-board ethernet controllers.
 */
int board_eth_init(bd_t *bis)
{
#ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII
        /* Select RMII fucntion through the expander */
        if (rmii_hw_init())
                printf("RMII hardware init failed!!!\n");
#endif
        if (!davinci_emac_initialize()) {
                printf("Error: Ethernet init failed!\n");
                return -1;
        }

        return 0;
}
#endif /* CONFIG_DRIVER_TI_EMAC */