/*
 * (C) Copyright 2003-2005
 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
 *
 * (C) Copyright 2010
 * Sergei Poselenov, Emcraft Systems, sposelenov@emcraft.com.
 *
 * SPDX-License-Identifier:     GPL-2.0+
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * High Level Configuration Options
 * (easy to change)
 */

#define CONFIG_MPC5xxx          1       /* This is an MPC5xxx CPU */
#define CONFIG_MPC5200          1       /* (more precisely a MPC5200 CPU) */
#define CONFIG_A4M072           1       /* ... on A4M072 board */
#define CONFIG_MPC5200_DDR      1       /* ... use DDR RAM */

#define CONFIG_SYS_TEXT_BASE    0xFE000000

#define CONFIG_MISC_INIT_R

#define CONFIG_SYS_MPC5XXX_CLKIN        33000000 /* ... running at 33.000000MHz */

#define CONFIG_HIGH_BATS        1       /* High BATs supported */

/*
 * Serial console configuration
 */
#define CONFIG_PSC_CONSOLE      1       /* console is on PSC1 */
#define CONFIG_BAUDRATE         9600    /* ... at 9600 bps */
#define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200, 230400 }
/* define to enable silent console */
#define CONFIG_SILENT_CONSOLE
#define CONFIG_SYS_DEVICE_NULLDEV       1       /* include nulldev device */

/*
 * PCI Mapping:
 * 0x40000000 - 0x4fffffff - PCI Memory
 * 0x50000000 - 0x50ffffff - PCI IO Space
 */
#define CONFIG_PCI

#if defined(CONFIG_PCI)
#define CONFIG_PCI_PNP          1
#define CONFIG_PCI_SCAN_SHOW    1
#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1

#define CONFIG_PCI_MEM_BUS      0x40000000
#define CONFIG_PCI_MEM_PHYS     CONFIG_PCI_MEM_BUS
#define CONFIG_PCI_MEM_SIZE     0x10000000

#define CONFIG_PCI_IO_BUS       0x50000000
#define CONFIG_PCI_IO_PHYS      CONFIG_PCI_IO_BUS
#define CONFIG_PCI_IO_SIZE      0x01000000
#endif

#define CONFIG_SYS_XLB_PIPELINING       1

#undef CONFIG_EEPRO100

/* Partitions */
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION

/* USB */
#define CONFIG_USB_OHCI_NEW
#define CONFIG_USB_STORAGE
#define CONFIG_SYS_OHCI_BE_CONTROLLER
#undef CONFIG_SYS_USB_OHCI_BOARD_INIT
#define CONFIG_SYS_USB_OHCI_CPU_INIT    1
#define CONFIG_SYS_USB_OHCI_REGS_BASE   MPC5XXX_USB
#define CONFIG_SYS_USB_OHCI_SLOT_NAME   "mpc5200"
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS      15

#define CONFIG_TIMESTAMP                /* Print image info with timestamp */

/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME


/*
 * Command line configuration.
 */
#include <config_cmd_default.h>

#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_FAT
#define CONFIG_CMD_I2C
#define CONFIG_CMD_IDE
#define CONFIG_CMD_NFS
#define CONFIG_CMD_SNTP
#define CONFIG_CMD_USB
#define CONFIG_CMD_MII
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_PING
#define CONFIG_CMD_DISPLAY

#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
#endif

#if (CONFIG_SYS_TEXT_BASE == 0xFE000000)                /* Boot low with 32 MB Flash */
#define CONFIG_SYS_LOWBOOT              1
#define CONFIG_SYS_LOWBOOT32            1
#endif

/*
 * Autobooting
 */
#define CONFIG_BOOTDELAY        2       /* autoboot after 2 seconds */

#define CONFIG_SYS_AUTOLOAD     "n"

#define CONFIG_AUTOBOOT_KEYED
#define CONFIG_AUTOBOOT_PROMPT          "autoboot in %d seconds\n", bootdelay
#define CONFIG_AUTOBOOT_DELAY_STR       "asdfg"

#undef  CONFIG_BOOTARGS
#define CONFIG_PREBOOT                          "run try_update"

#define CONFIG_EXTRA_ENV_SETTINGS                                       \
        "bk=run add_mtd ; run add_consolespec ; bootm 200000\0"         \
        "cf1=diskboot 200000 0:1\0"                                     \
        "bootcmd_cf1=run bcf1\0"                                        \
        "bcf=setenv bootargs root=/dev/hda3\0"                          \
        "bootcmd_nfs=run bnfs\0"                                        \
        "norargs=setenv bootargs root=/dev/mtdblock3 rootfstype=cramfs "\
                "panic=1\0"                                             \
        "bootcmd_nor=cp.b ${kernel_addr} 200000 100000;"                \
                        "run norargs addip; run bk\0"                   \
        "bnfs=nfs 200000 ${rootpath}/boot/uImage;"                      \
                        "run nfsargs addip ; run bk\0"                  \
        "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
                                "nfsroot=${serverip}:${rootpath}\0"     \
        "try_update=usb start;sleep 2;usb start;sleep 1;"               \
                        "fatload usb 0 2F0000 PCPUUPDT 2FF;usb stop;"   \
                        "source 2F0000\0"                               \
        "env_addr=FE060000\0"                                           \
        "kernel_addr=FE100000\0"                                        \
        "rootfs_addr=FE200000\0"                                        \
        "add_mtd=setenv bootargs ${bootargs} mtdparts="                 \
                "phys_mapped_flash:384k(u),640k(e),1m(k),30m(r)\0"      \
        "bcf1=run cf1; run bcf; run addip; run bk\0"                    \
        "add_consolespec=setenv bootargs ${bootargs} "                  \
                                "console=/dev/null quiet\0"             \
        "addip=if test -n ${ethaddr};"                                  \
                "then if test -n ${ipaddr};"                            \
                        "then setenv bootargs ${bootargs} "             \
                                "ip=${ipaddr}:${serverip}:${gatewayip}:"\
                                "${netmask}:${hostname}:${netdev}:off;" \
                        "fi;"                                           \
                "else;"                                                 \
                        "setenv bootargs ${bootargs} no_ethaddr;"       \
                "fi\0"                                                  \
        "hostname=CPUP0\0"                                              \
        "ethaddr=00:00:00:00:00:00\0"                                   \
        "netdev=eth0\0"                                                 \
        "bootcmd=run bootcmd_nor\0"                                     \
        ""
/*
 * IPB Bus clocking configuration.
 */
#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK          /* define for 133MHz speed */

/*
 * I2C configuration
 */
#define CONFIG_HARD_I2C                 1       /* I2C with hardware support */
#define CONFIG_SYS_I2C_MODULE           2       /* Select I2C module #1 or #2 */

#define CONFIG_SYS_I2C_SPEED            100000 /* 100 kHz */
#define CONFIG_SYS_I2C_SLAVE            0x7F

/*
 * EEPROM configuration
 */
#define CONFIG_SYS_I2C_EEPROM_ADDR              0x52    /* 1010010x */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          2
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       6
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10
#define CONFIG_SYS_EEPROM_WREN                  1
#define CONFIG_SYS_EEPROM_WP                    GPIO_PSC2_4

/*
 * Flash configuration
 */
#define CONFIG_SYS_FLASH_BASE           0xFE000000
#define CONFIG_SYS_FLASH_SIZE           0x02000000
#if !defined(CONFIG_SYS_LOWBOOT)
#error "CONFIG_SYS_LOWBOOT not defined?"
#else   /* CONFIG_SYS_LOWBOOT */
#if defined(CONFIG_SYS_LOWBOOT32)
#define CONFIG_ENV_ADDR         (CONFIG_SYS_FLASH_BASE + 0x00060000)
#endif
#endif  /* CONFIG_SYS_LOWBOOT */

#define CONFIG_SYS_MAX_FLASH_BANKS      1       /* max num of memory banks      */
#define CONFIG_SYS_MAX_FLASH_SECT       256     /* max num of sects on one chip */
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_16BIT
#define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_CS0_START}
#define CONFIG_SYS_FLASH_BANKS_SIZES    {CONFIG_SYS_CS0_SIZE}

/*
 * Environment settings
 */
#define CONFIG_ENV_IS_IN_FLASH  1
#define CONFIG_ENV_SIZE         0x10000
#define CONFIG_ENV_SECT_SIZE    0x20000
#define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND  CONFIG_ENV_SIZE

#define CONFIG_ENV_OVERWRITE    1

/*
 * Memory map
 */
#define CONFIG_SYS_MBAR         0xF0000000
#define CONFIG_SYS_SDRAM_BASE   0x00000000
#define CONFIG_SYS_DEFAULT_MBAR 0x80000000

/* Use SRAM until RAM will be available */
#define CONFIG_SYS_INIT_RAM_ADDR        MPC5XXX_SRAM
#define CONFIG_SYS_INIT_RAM_SIZE                MPC5XXX_SRAM_SIZE       /* Size of used area in DPRAM */


#define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET

#define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
#   define CONFIG_SYS_RAMBOOT           1
#endif

#define CONFIG_SYS_MONITOR_LEN          (384 << 10)     /* Reserve 384 kB for Monitor   */
#define CONFIG_SYS_MALLOC_LEN           (128 << 10)     /* Reserve 128 kB for malloc()  */
#define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* Initial Memory map for Linux */

/*
 * Ethernet configuration
 */
#define CONFIG_MPC5xxx_FEC      1
#define CONFIG_MPC5xxx_FEC_MII100
/*
 * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb
 */
/* #define CONFIG_MPC5xxx_FEC_MII10 */
#define CONFIG_PHY_ADDR         0x1f
#define CONFIG_PHY_TYPE         0x79c874                /* AMD Phy Controller */

/*
 * GPIO configuration
 */
#define CONFIG_SYS_GPS_PORT_CONFIG      0x18000004

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_CMDLINE_EDITING  1
#define CONFIG_SYS_LONGHELP                     /* undef to save memory     */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE               1024    /* Console I/O Buffer Size  */
#else
#define CONFIG_SYS_CBSIZE               256     /* Console I/O Buffer Size  */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)      /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS              16              /* max number of command args   */
#define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */

#define CONFIG_SYS_MEMTEST_START        0x00100000      /* memtest works on */
#define CONFIG_SYS_MEMTEST_END          0x00f00000      /* 1 ... 15 MB in DRAM  */

#define CONFIG_SYS_LOAD_ADDR            0x100000        /* default load address */

#define CONFIG_SYS_CACHELINE_SIZE       32      /* For MPC5xxx CPUs */
#if defined(CONFIG_CMD_KGDB)
#  define CONFIG_SYS_CACHELINE_SHIFT    5       /* log base 2 of the above value */
#endif


/*
 * Various low-level settings
 */
#define CONFIG_SYS_HID0_INIT            HID0_ICE | HID0_ICFI
#define CONFIG_SYS_HID0_FINAL           HID0_ICE
/* Flash at CSBoot, CS0 */
#define CONFIG_SYS_BOOTCS_START         CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_BOOTCS_SIZE          CONFIG_SYS_FLASH_SIZE
#define CONFIG_SYS_BOOTCS_CFG           0x0002DD00
#define CONFIG_SYS_CS0_START            CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_CS0_SIZE             CONFIG_SYS_FLASH_SIZE
/* External SRAM at CS1 */
#define CONFIG_SYS_CS1_START            0x62000000
#define CONFIG_SYS_CS1_SIZE             0x00400000
#define CONFIG_SYS_CS1_CFG              0x00009930
#define CONFIG_SYS_SRAM_BASE            CONFIG_SYS_CS1_START
#define CONFIG_SYS_SRAM_SIZE            CONFIG_SYS_CS1_SIZE
/* LED display at CS7 */
#define CONFIG_SYS_CS7_START            0x6a000000
#define CONFIG_SYS_CS7_SIZE             (64*1024)
#define CONFIG_SYS_CS7_CFG              0x0000bf30

#define CONFIG_SYS_CS_BURST             0x00000000
#define CONFIG_SYS_CS_DEADCYCLE         0x33333003

#define CONFIG_SYS_RESET_ADDRESS        0xff000000

/*-----------------------------------------------------------------------
 * USB stuff
 *-----------------------------------------------------------------------
 */
#define CONFIG_USB_CLOCK        0x0001BBBB
#define CONFIG_USB_CONFIG       0x00001000 /* 0x4000 for SE mode */

/*-----------------------------------------------------------------------
 * IDE/ATA stuff Supports IDE harddisk
 *-----------------------------------------------------------------------
 */

#undef  CONFIG_IDE_8xx_PCCARD           /* Use IDE with PC Card Adapter */

#undef  CONFIG_IDE_8xx_DIRECT           /* Direct IDE    not supported  */
#undef  CONFIG_IDE_LED                  /* LED   for ide not supported  */

#define CONFIG_IDE_PREINIT

#define CONFIG_SYS_IDE_MAXBUS           1       /* max. 1 IDE bus               */
#define CONFIG_SYS_IDE_MAXDEVICE        1       /* max. 2 drives per IDE bus    */

#define CONFIG_SYS_ATA_IDE0_OFFSET      0x0000

#define CONFIG_SYS_ATA_BASE_ADDR        MPC5XXX_ATA

/* Offset for data I/O                  */
#define CONFIG_SYS_ATA_DATA_OFFSET      (0x0060)

/* Offset for normal register accesses  */
#define CONFIG_SYS_ATA_REG_OFFSET       (CONFIG_SYS_ATA_DATA_OFFSET)

/* Offset for alternate registers       */
#define CONFIG_SYS_ATA_ALT_OFFSET       (0x005C)

/* Interval between registers                                                */
#define CONFIG_SYS_ATA_STRIDE          4

#define CONFIG_ATAPI                   1

/*-----------------------------------------------------------------------
 * Open firmware flat tree support
 *-----------------------------------------------------------------------
 */
#define CONFIG_OF_LIBFDT        1
#define CONFIG_OF_BOARD_SETUP   1

#define OF_CPU                  "PowerPC,5200@0"
#define OF_SOC                  "soc5200@f0000000"
#define OF_TBCLK                (bd->bi_busfreq / 4)
#define OF_STDOUT_PATH          "/soc5200@f0000000/serial@2000"

/* Support for the 7-segment display */
#define CONFIG_SYS_DISP_CHR_RAM      CONFIG_SYS_CS7_START
#define CONFIG_SHOW_ACTIVITY            /* used for display realization */

#define CONFIG_SHOW_BOOT_PROGRESS

#endif /* __CONFIG_H */