/*
 * Copyright 2011-2012 Freescale Semiconductor, Inc.
 *
 * SPDX-License-Identifier:     GPL-2.0+
 */

/*
 * P2041 RDB board configuration file
 * Also supports P2040 RDB
 */
#ifndef __CONFIG_H
#define __CONFIG_H

#define CONFIG_P2041RDB
#define CONFIG_PHYS_64BIT
#define CONFIG_PPC_P2041

#ifdef CONFIG_RAMBOOT_PBL
#define CONFIG_RAMBOOT_TEXT_BASE        CONFIG_SYS_TEXT_BASE
#define CONFIG_RESET_VECTOR_ADDRESS     0xfffffffc
#define CONFIG_SYS_FSL_PBL_PBI board/freescale/corenet_ds/pbi.cfg
#define CONFIG_SYS_FSL_PBL_RCW board/freescale/corenet_ds/rcw_p2041rdb.cfg
#endif

#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
/* Set 1M boot space */
#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
                (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
#define CONFIG_SYS_NO_FLASH
#endif

/* High Level Configuration Options */
#define CONFIG_BOOKE
#define CONFIG_E500                     /* BOOKE e500 family */
#define CONFIG_E500MC                   /* BOOKE e500mc family */
#define CONFIG_SYS_BOOK3E_HV            /* Category E.HV supported */
#define CONFIG_MP                       /* support multiple processors */

#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE    0xeff40000
#endif

#ifndef CONFIG_RESET_VECTOR_ADDRESS
#define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
#endif

#define CONFIG_SYS_FSL_CPC              /* Corenet Platform Cache */
#define CONFIG_SYS_NUM_CPC              CONFIG_NUM_DDR_CONTROLLERS
#define CONFIG_FSL_ELBC                 /* Has Enhanced localbus controller */
#define CONFIG_PCI                      /* Enable PCI/PCIE */
#define CONFIG_PCIE1                    /* PCIE controler 1 */
#define CONFIG_PCIE2                    /* PCIE controler 2 */
#define CONFIG_PCIE3                    /* PCIE controler 3 */
#define CONFIG_FSL_PCI_INIT             /* Use common FSL init code */
#define CONFIG_SYS_PCI_64BIT            /* enable 64-bit PCI resources */

#define CONFIG_SYS_SRIO
#define CONFIG_SRIO1                    /* SRIO port 1 */
#define CONFIG_SRIO2                    /* SRIO port 2 */
#define CONFIG_SRIO_PCIE_BOOT_MASTER
#define CONFIG_SYS_DPAA_RMAN            /* RMan */

#define CONFIG_FSL_LAW                  /* Use common FSL init code */

#define CONFIG_ENV_OVERWRITE

#ifdef CONFIG_SYS_NO_FLASH
#if !defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
#define CONFIG_ENV_IS_NOWHERE
#endif
#else
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#endif

#if defined(CONFIG_SPIFLASH)
        #define CONFIG_SYS_EXTRA_ENV_RELOC
        #define CONFIG_ENV_IS_IN_SPI_FLASH
        #define CONFIG_ENV_SPI_BUS              0
        #define CONFIG_ENV_SPI_CS               0
        #define CONFIG_ENV_SPI_MAX_HZ           10000000
        #define CONFIG_ENV_SPI_MODE             0
        #define CONFIG_ENV_SIZE                 0x2000          /* 8KB */
        #define CONFIG_ENV_OFFSET               0x100000        /* 1MB */
        #define CONFIG_ENV_SECT_SIZE            0x10000
#elif defined(CONFIG_SDCARD)
        #define CONFIG_SYS_EXTRA_ENV_RELOC
        #define CONFIG_ENV_IS_IN_MMC
        #define CONFIG_FSL_FIXED_MMC_LOCATION
        #define CONFIG_SYS_MMC_ENV_DEV          0
        #define CONFIG_ENV_SIZE                 0x2000
        #define CONFIG_ENV_OFFSET               (512 * 1658)
#elif defined(CONFIG_NAND)
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_SIZE                 CONFIG_SYS_NAND_BLOCK_SIZE
#define CONFIG_ENV_OFFSET               (7 * CONFIG_SYS_NAND_BLOCK_SIZE)
#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
#define CONFIG_ENV_IS_IN_REMOTE
#define CONFIG_ENV_ADDR         0xffe20000
#define CONFIG_ENV_SIZE         0x2000
#elif defined(CONFIG_ENV_IS_NOWHERE)
#define CONFIG_ENV_SIZE         0x2000
#else
        #define CONFIG_ENV_IS_IN_FLASH
        #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE \
                        - CONFIG_ENV_SECT_SIZE)
        #define CONFIG_ENV_SIZE         0x2000
        #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */
#endif

#ifndef __ASSEMBLY__
unsigned long get_board_sys_clk(unsigned long dummy);
#endif
#define CONFIG_SYS_CLK_FREQ     get_board_sys_clk(0)

/*
 * These can be toggled for performance analysis, otherwise use default.
 */
#define CONFIG_SYS_CACHE_STASHING
#define CONFIG_BACKSIDE_L2_CACHE
#define CONFIG_SYS_INIT_L2CSR0          L2CSR0_L2E
#define CONFIG_BTB                      /* toggle branch predition */

#define CONFIG_ENABLE_36BIT_PHYS

#ifdef CONFIG_PHYS_64BIT
#define CONFIG_ADDR_MAP
#define CONFIG_SYS_NUM_ADDR_MAP         64      /* number of TLB1 entries */
#endif

#define CONFIG_POST CONFIG_SYS_POST_MEMORY      /* test POST memory test */
#define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest works on */
#define CONFIG_SYS_MEMTEST_END          0x00400000
#define CONFIG_SYS_ALT_MEMTEST
#define CONFIG_PANIC_HANG       /* do not reset board on panic */

/*
 *  Config the L3 Cache as L3 SRAM
 */
#define CONFIG_SYS_INIT_L3_ADDR         CONFIG_RAMBOOT_TEXT_BASE
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_INIT_L3_ADDR_PHYS    (0xf00000000ull | \
                CONFIG_RAMBOOT_TEXT_BASE)
#else
#define CONFIG_SYS_INIT_L3_ADDR_PHYS    CONFIG_SYS_INIT_L3_ADDR
#endif
#define CONFIG_SYS_L3_SIZE              (1024 << 10)
#define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)

#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_DCSRBAR              0xf0000000
#define CONFIG_SYS_DCSRBAR_PHYS         0xf00000000ull
#endif

/* EEPROM */
#define CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM       0
#define CONFIG_SYS_I2C_EEPROM_ADDR      0x50
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  1

/*
 * DDR Setup
 */
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
#define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE

#define CONFIG_DIMM_SLOTS_PER_CTLR      1
#define CONFIG_CHIP_SELECTS_PER_CTRL    (4 * CONFIG_DIMM_SLOTS_PER_CTLR)

#define CONFIG_DDR_SPD
#define CONFIG_SYS_FSL_DDR3

#define CONFIG_SYS_SPD_BUS_NUM  0
#define SPD_EEPROM_ADDRESS      0x52
#define CONFIG_SYS_SDRAM_SIZE   4096    /* for fixed parameter use */

/*
 * Local Bus Definitions
 */

/* Set the local bus clock 1/8 of platform clock */
#define CONFIG_SYS_LBC_LCRR             LCRR_CLKDIV_8

/*
 * This board doesn't have a promjet connector.
 * However, it uses commone corenet board LAW and TLB.
 * It is necessary to use the same start address with proper offset.
 */
#define CONFIG_SYS_FLASH_BASE           0xe0000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_FLASH_BASE_PHYS      0xfe0000000ull
#else
#define CONFIG_SYS_FLASH_BASE_PHYS      CONFIG_SYS_FLASH_BASE
#endif

#define CONFIG_SYS_FLASH_BR_PRELIM \
                (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | \
                BR_PS_16 | BR_V)
#define CONFIG_SYS_FLASH_OR_PRELIM \
                ((0xf8000ff7 & ~OR_GPCM_SCY & ~OR_GPCM_EHTR) \
                 | OR_GPCM_SCY_8 | OR_GPCM_EHTR_CLEAR)

#define CONFIG_FSL_CPLD
#define CPLD_BASE               0xffdf0000      /* CPLD registers */
#ifdef CONFIG_PHYS_64BIT
#define CPLD_BASE_PHYS          0xfffdf0000ull
#else
#define CPLD_BASE_PHYS          CPLD_BASE
#endif

#define CONFIG_SYS_BR3_PRELIM   (BR_PHYS_ADDR(CPLD_BASE_PHYS) | BR_PS_8 | BR_V)
#define CONFIG_SYS_OR3_PRELIM   0xffffeff7      /* 32KB but only 4k mapped */

#define PIXIS_LBMAP_SWITCH      7
#define PIXIS_LBMAP_MASK        0xf0
#define PIXIS_LBMAP_SHIFT       4
#define PIXIS_LBMAP_ALTBANK     0x40

#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */

#define CONFIG_SYS_MAX_FLASH_BANKS      1               /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT       1024            /* sectors per device */
#define CONFIG_SYS_FLASH_ERASE_TOUT     60000           /* Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT     500             /* Write Timeout (ms) */

#define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_TEXT_BASE

#if defined(CONFIG_RAMBOOT_PBL)
#define CONFIG_SYS_RAMBOOT
#endif

#define CONFIG_NAND_FSL_ELBC
/* Nand Flash */
#ifdef CONFIG_NAND_FSL_ELBC
#define CONFIG_SYS_NAND_BASE            0xffa00000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_NAND_BASE_PHYS       0xfffa00000ull
#else
#define CONFIG_SYS_NAND_BASE_PHYS       CONFIG_SYS_NAND_BASE
#endif

#define CONFIG_SYS_NAND_BASE_LIST     {CONFIG_SYS_NAND_BASE}
#define CONFIG_SYS_MAX_NAND_DEVICE      1
#define CONFIG_MTD_NAND_VERIFY_WRITE
#define CONFIG_CMD_NAND
#define CONFIG_SYS_NAND_BLOCK_SIZE    (128 * 1024)

/* NAND flash config */
#define CONFIG_SYS_NAND_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
                               | (2<<BR_DECC_SHIFT)    /* Use HW ECC */ \
                               | BR_PS_8               /* Port Size = 8 bit */ \
                               | BR_MS_FCM             /* MSEL = FCM */ \
                               | BR_V)                 /* valid */
#define CONFIG_SYS_NAND_OR_PRELIM  (0xFFFC0000        /* length 256K */ \
                               | OR_FCM_PGS            /* Large Page*/ \
                               | OR_FCM_CSCT \
                               | OR_FCM_CST \
                               | OR_FCM_CHT \
                               | OR_FCM_SCY_1 \
                               | OR_FCM_TRLX \
                               | OR_FCM_EHTR)

#ifdef CONFIG_NAND
#define CONFIG_SYS_BR0_PRELIM  CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
#define CONFIG_SYS_OR0_PRELIM  CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
#define CONFIG_SYS_BR1_PRELIM  CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */
#define CONFIG_SYS_OR1_PRELIM  CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */
#else
#define CONFIG_SYS_BR0_PRELIM  CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */
#define CONFIG_SYS_OR0_PRELIM  CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */
#define CONFIG_SYS_BR1_PRELIM  CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
#define CONFIG_SYS_OR1_PRELIM  CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
#endif
#else
#define CONFIG_SYS_BR0_PRELIM  CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */
#define CONFIG_SYS_OR0_PRELIM  CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */
#endif /* CONFIG_NAND_FSL_ELBC */

#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7
#define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000}

#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_EARLY_INIT_R       /* call board_early_init_r function */
#define CONFIG_MISC_INIT_R

#define CONFIG_HWCONFIG

/* define to use L1 as initial stack */
#define CONFIG_L1_INIT_RAM
#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR        0xffd00000      /* Initial L1 address */
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
/* The assembler doesn't like typecast */
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
        ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
          CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
#else
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS   CONFIG_SYS_INIT_RAM_ADDR
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
#endif
#define CONFIG_SYS_INIT_RAM_SIZE        0x00004000

#define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
                                        GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET

#define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
#define CONFIG_SYS_MALLOC_LEN           (1024 * 1024)

/* Serial Port - controlled on board with jumper J8
 * open - index 2
 * shorted - index 1
 */
#define CONFIG_CONS_INDEX       1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE     1
#define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)

#define CONFIG_SYS_BAUDRATE_TABLE       \
        {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)

/* Use the HUSH parser */
#define CONFIG_SYS_HUSH_PARSER

/* pass open firmware flat tree */
#define CONFIG_OF_LIBFDT
#define CONFIG_OF_BOARD_SETUP
#define CONFIG_OF_STDOUT_VIA_ALIAS

/* new uImage format support */
#define CONFIG_FIT
#define CONFIG_FIT_VERBOSE      /* enable fit_format_{error,warning}() */

/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED        400000
#define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET       0x118000
#define CONFIG_SYS_FSL_I2C2_SPEED       400000
#define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
#define CONFIG_SYS_FSL_I2C2_OFFSET      0x118100

/*
 * RapidIO
 */
#define CONFIG_SYS_SRIO1_MEM_VIRT       0xa0000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_SRIO1_MEM_PHYS       0xc20000000ull
#else
#define CONFIG_SYS_SRIO1_MEM_PHYS       0xa0000000
#endif
#define CONFIG_SYS_SRIO1_MEM_SIZE       0x10000000      /* 256M */

#define CONFIG_SYS_SRIO2_MEM_VIRT       0xb0000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_SRIO2_MEM_PHYS       0xc30000000ull
#else
#define CONFIG_SYS_SRIO2_MEM_PHYS       0xb0000000
#endif
#define CONFIG_SYS_SRIO2_MEM_SIZE       0x10000000      /* 256M */

/*
 * for slave u-boot IMAGE instored in master memory space,
 * PHYS must be aligned based on the SIZE
 */
#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000       /* 1M */
#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
/*
 * for slave UCODE and ENV instored in master memory space,
 * PHYS must be aligned based on the SIZE
 */
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000    /* 256K */

/* slave core release by master*/
#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */

/*
 * SRIO_PCIE_BOOT - SLAVE
 */
#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
                (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
#endif

/*
 * eSPI - Enhanced SPI
 */
#define CONFIG_FSL_ESPI
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_SPANSION
#define CONFIG_CMD_SF
#define CONFIG_SF_DEFAULT_SPEED         10000000
#define CONFIG_SF_DEFAULT_MODE          0

/*
 * General PCI
 * Memory space is mapped 1-1, but I/O space must start from 0.
 */

/* controller 1, direct to uli, tgtid 3, Base address 20000 */
#define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE1_MEM_BUS        0xe0000000
#define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
#else
#define CONFIG_SYS_PCIE1_MEM_BUS        0x80000000
#define CONFIG_SYS_PCIE1_MEM_PHYS       0x80000000
#endif
#define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
#define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
#define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull
#else
#define CONFIG_SYS_PCIE1_IO_PHYS        0xf8000000
#endif
#define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */

/* controller 2, Slot 2, tgtid 2, Base address 201000 */
#define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE2_MEM_BUS        0xe0000000
#define CONFIG_SYS_PCIE2_MEM_PHYS       0xc20000000ull
#else
#define CONFIG_SYS_PCIE2_MEM_BUS        0xa0000000
#define CONFIG_SYS_PCIE2_MEM_PHYS       0xa0000000
#endif
#define CONFIG_SYS_PCIE2_MEM_SIZE       0x20000000      /* 512M */
#define CONFIG_SYS_PCIE2_IO_VIRT        0xf8010000
#define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE2_IO_PHYS        0xff8010000ull
#else
#define CONFIG_SYS_PCIE2_IO_PHYS        0xf8010000
#endif
#define CONFIG_SYS_PCIE2_IO_SIZE        0x00010000      /* 64k */

/* controller 3, Slot 1, tgtid 1, Base address 202000 */
#define CONFIG_SYS_PCIE3_MEM_VIRT       0xc0000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE3_MEM_BUS        0xe0000000
#define CONFIG_SYS_PCIE3_MEM_PHYS       0xc40000000ull
#else
#define CONFIG_SYS_PCIE3_MEM_BUS        0xc0000000
#define CONFIG_SYS_PCIE3_MEM_PHYS       0xc0000000
#endif
#define CONFIG_SYS_PCIE3_MEM_SIZE       0x20000000      /* 512M */
#define CONFIG_SYS_PCIE3_IO_VIRT        0xf8020000
#define CONFIG_SYS_PCIE3_IO_BUS         0x00000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE3_IO_PHYS        0xff8020000ull
#else
#define CONFIG_SYS_PCIE3_IO_PHYS        0xf8020000
#endif
#define CONFIG_SYS_PCIE3_IO_SIZE        0x00010000      /* 64k */

/* Qman/Bman */
#define CONFIG_SYS_DPAA_QBMAN           /* Support Q/Bman */
#define CONFIG_SYS_BMAN_NUM_PORTALS     10
#define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
#else
#define CONFIG_SYS_BMAN_MEM_PHYS        CONFIG_SYS_BMAN_MEM_BASE
#endif
#define CONFIG_SYS_BMAN_MEM_SIZE        0x00200000
#define CONFIG_SYS_QMAN_NUM_PORTALS     10
#define CONFIG_SYS_QMAN_MEM_BASE        0xf4200000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_QMAN_MEM_PHYS        0xff4200000ull
#else
#define CONFIG_SYS_QMAN_MEM_PHYS        CONFIG_SYS_QMAN_MEM_BASE
#endif
#define CONFIG_SYS_QMAN_MEM_SIZE        0x00200000

#define CONFIG_SYS_DPAA_FMAN
#define CONFIG_SYS_DPAA_PME
/* Default address of microcode for the Linux Fman driver */
#if defined(CONFIG_SPIFLASH)
/*
 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
 * env, so we got 0x110000.
 */
#define CONFIG_SYS_QE_FW_IN_SPIFLASH
#define CONFIG_SYS_FMAN_FW_ADDR 0x110000
#elif defined(CONFIG_SDCARD)
/*
 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 * about 825KB (1650 blocks), Env is stored after the image, and the env size is
 * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
 */
#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
#define CONFIG_SYS_FMAN_FW_ADDR (512 * 1680)
#elif defined(CONFIG_NAND)
#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
#define CONFIG_SYS_FMAN_FW_ADDR (8 * CONFIG_SYS_NAND_BLOCK_SIZE)
#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
/*
 * Slave has no ucode locally, it can fetch this from remote. When implementing
 * in two corenet boards, slave's ucode could be stored in master's memory
 * space, the address can be mapped from slave TLB->slave LAW->
 * slave SRIO or PCIE outbound window->master inbound window->
 * master LAW->the ucode address in master's memory space.
 */
#define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
#define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000
#else
#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
#endif
#define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
#define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)

#ifdef CONFIG_SYS_DPAA_FMAN
#define CONFIG_FMAN_ENET
#define CONFIG_PHYLIB_10G
#define CONFIG_PHY_VITESSE
#define CONFIG_PHY_TERANETICS
#endif

#ifdef CONFIG_PCI
#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_PCI_PNP                  /* do pci plug-and-play */
#define CONFIG_E1000

#define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
#define CONFIG_DOS_PARTITION
#endif  /* CONFIG_PCI */

/* SATA */
#define CONFIG_FSL_SATA_V2

#ifdef CONFIG_FSL_SATA_V2
#define CONFIG_FSL_SATA
#define CONFIG_LIBATA

#define CONFIG_SYS_SATA_MAX_DEVICE      2
#define CONFIG_SATA1
#define CONFIG_SYS_SATA1                CONFIG_SYS_MPC85xx_SATA1_ADDR
#define CONFIG_SYS_SATA1_FLAGS          FLAGS_DMA
#define CONFIG_SATA2
#define CONFIG_SYS_SATA2                CONFIG_SYS_MPC85xx_SATA2_ADDR
#define CONFIG_SYS_SATA2_FLAGS          FLAGS_DMA

#define CONFIG_LBA48
#define CONFIG_CMD_SATA
#define CONFIG_DOS_PARTITION
#define CONFIG_CMD_EXT2
#endif

#ifdef CONFIG_FMAN_ENET
#define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR  0x2
#define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR  0x3
#define CONFIG_SYS_FM1_DTSEC3_PHY_ADDR  0x4
#define CONFIG_SYS_FM1_DTSEC4_PHY_ADDR  0x1
#define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR  0x0

#define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR    0x1c
#define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR    0x1d
#define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR    0x1e
#define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR    0x1f

#define CONFIG_SYS_FM1_10GEC1_PHY_ADDR  0

#define CONFIG_SYS_TBIPA_VALUE  8
#define CONFIG_MII              /* MII PHY management */
#define CONFIG_ETHPRIME         "FM1@DTSEC1"
#define CONFIG_PHY_GIGE         /* Include GbE speed/duplex detection */
#endif

/*
 * Environment
 */
#define CONFIG_LOADS_ECHO               /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change */

/*
 * Command line configuration.
 */
#include <config_cmd_default.h>

#define CONFIG_CMD_DHCP
#define CONFIG_CMD_ELF
#define CONFIG_CMD_ERRATA
#define CONFIG_CMD_GREPENV
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_SETEXPR

#ifdef CONFIG_PCI
#define CONFIG_CMD_PCI
#define CONFIG_CMD_NET
#endif

/*
* USB
*/
#define CONFIG_HAS_FSL_DR_USB
#define CONFIG_HAS_FSL_MPH_USB

#if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB)
#define CONFIG_CMD_USB
#define CONFIG_USB_STORAGE
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif

#define CONFIG_CMD_EXT2

#define CONFIG_MMC

#ifdef CONFIG_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
#define CONFIG_CMD_MMC
#define CONFIG_GENERIC_MMC
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
#endif

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP                     /* undef to save memory */
#define CONFIG_CMDLINE_EDITING                  /* Command-line editing */
#define CONFIG_AUTO_COMPLETE                    /* add autocompletion support */
#define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
#ifdef CONFIG_CMD_KGDB
#define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size */
#endif
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE       (CONFIG_SYS_CBSIZE + \
                                sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS      16              /* max number of command args */
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 64 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial Memory for Linux */
#define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */

#ifdef CONFIG_CMD_KGDB
#define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
#endif

/*
 * Environment Configuration
 */
#define CONFIG_ROOTPATH         "/opt/nfsroot"
#define CONFIG_BOOTFILE         "uImage"
#define CONFIG_UBOOTPATH        u-boot.bin

/* default location for tftp and bootm */
#define CONFIG_LOADADDR         1000000

#define CONFIG_BOOTDELAY        10      /* -1 disables auto-boot */

#define CONFIG_BAUDRATE 115200

#define __USB_PHY_TYPE  utmi

#define CONFIG_EXTRA_ENV_SETTINGS                               \
        "hwconfig=fsl_ddr:ctlr_intlv=cacheline,"                \
        "bank_intlv=cs0_cs1\0"                                  \
        "netdev=eth0\0"                                         \
        "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"                     \
        "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"             \
        "tftpflash=tftpboot $loadaddr $uboot && "               \
        "protect off $ubootaddr +$filesize && "                 \
        "erase $ubootaddr +$filesize && "                       \
        "cp.b $loadaddr $ubootaddr $filesize && "               \
        "protect on $ubootaddr +$filesize && "                  \
        "cmp.b $loadaddr $ubootaddr $filesize\0"                \
        "consoledev=ttyS0\0"                                    \
        "usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0"                \
        "usb_dr_mode=host\0"                                    \
        "ramdiskaddr=2000000\0"                                 \
        "ramdiskfile=p2041rdb/ramdisk.uboot\0"                  \
        "fdtaddr=c00000\0"                                      \
        "fdtfile=p2041rdb/p2041rdb.dtb\0"                       \
        "bdev=sda3\0"

#define CONFIG_HDBOOT                                   \
        "setenv bootargs root=/dev/$bdev rw "           \
        "console=$consoledev,$baudrate $othbootargs;"   \
        "tftp $loadaddr $bootfile;"                     \
        "tftp $fdtaddr $fdtfile;"                       \
        "bootm $loadaddr - $fdtaddr"

#define CONFIG_NFSBOOTCOMMAND                   \
        "setenv bootargs root=/dev/nfs rw "     \
        "nfsroot=$serverip:$rootpath "          \
        "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
        "console=$consoledev,$baudrate $othbootargs;"   \
        "tftp $loadaddr $bootfile;"             \
        "tftp $fdtaddr $fdtfile;"               \
        "bootm $loadaddr - $fdtaddr"

#define CONFIG_RAMBOOTCOMMAND                           \
        "setenv bootargs root=/dev/ram rw "             \
        "console=$consoledev,$baudrate $othbootargs;"   \
        "tftp $ramdiskaddr $ramdiskfile;"               \
        "tftp $loadaddr $bootfile;"                     \
        "tftp $fdtaddr $fdtfile;"                       \
        "bootm $loadaddr $ramdiskaddr $fdtaddr"

#define CONFIG_BOOTCOMMAND              CONFIG_HDBOOT

#include <asm/fsl_secure_boot.h>

#endif  /* __CONFIG_H */