1/* 2 * Copyright (C) Freescale Semiconductor, Inc. 2006. 3 * 4 * (C) Copyright 2010 5 * Heiko Schocher, DENX Software Engineering, hs@denx.de. 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9/* 10 * ve8313 board configuration file 11 */ 12 13#ifndef __CONFIG_H 14#define __CONFIG_H 15 16/* 17 * High Level Configuration Options 18 */ 19#define CONFIG_E300 1 20#define CONFIG_MPC831x 1 21#define CONFIG_MPC8313 1 22#define CONFIG_VE8313 1 23 24#ifndef CONFIG_SYS_TEXT_BASE 25#define CONFIG_SYS_TEXT_BASE 0xfe000000 26#endif 27 28#define CONFIG_PCI 1 29#define CONFIG_PCI_INDIRECT_BRIDGE 1 30#define CONFIG_FSL_ELBC 1 31 32#define CONFIG_BOARD_EARLY_INIT_F 1 33 34/* 35 * On-board devices 36 * 37 */ 38#define CONFIG_83XX_CLKIN 32000000 /* in Hz */ 39 40#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN 41 42#define CONFIG_SYS_IMMR 0xE0000000 43 44#define CONFIG_SYS_MEMTEST_START 0x00001000 45#define CONFIG_SYS_MEMTEST_END 0x07000000 46 47#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth */ 48#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count */ 49 50/* 51 * Device configurations 52 */ 53 54/* 55 * DDR Setup 56 */ 57#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/ 58#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 59#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 60 61/* 62 * Manually set up DDR parameters, as this board does not 63 * have the SPD connected to I2C. 64 */ 65#define CONFIG_SYS_DDR_SIZE 128 /* MB */ 66#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ 67 | CSCONFIG_AP \ 68 | CSCONFIG_ODT_RD_NEVER \ 69 | CSCONFIG_ODT_WR_ALL \ 70 | CSCONFIG_ROW_BIT_13 \ 71 | CSCONFIG_COL_BIT_10) 72 /* 0x80840102 */ 73 74#define CONFIG_SYS_DDR_TIMING_3 0x00000000 75#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ 76 | (0 << TIMING_CFG0_WRT_SHIFT) \ 77 | (3 << TIMING_CFG0_RRT_SHIFT) \ 78 | (2 << TIMING_CFG0_WWT_SHIFT) \ 79 | (7 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ 80 | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ 81 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ 82 | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) 83 /* 0x0e720802 */ 84#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \ 85 | (6 << TIMING_CFG1_ACTTOPRE_SHIFT) \ 86 | (2 << TIMING_CFG1_ACTTORW_SHIFT) \ 87 | (5 << TIMING_CFG1_CASLAT_SHIFT) \ 88 | (6 << TIMING_CFG1_REFREC_SHIFT) \ 89 | (2 << TIMING_CFG1_WRREC_SHIFT) \ 90 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ 91 | (2 << TIMING_CFG1_WRTORD_SHIFT)) 92 /* 0x26256222 */ 93#define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \ 94 | (5 << TIMING_CFG2_CPO_SHIFT) \ 95 | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ 96 | (1 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ 97 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ 98 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ 99 | (7 << TIMING_CFG2_FOUR_ACT_SHIFT)) 100 /* 0x029028c7 */ 101#define CONFIG_SYS_DDR_INTERVAL ((0x320 << SDRAM_INTERVAL_REFINT_SHIFT) \ 102 | (0x2000 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) 103 /* 0x03202000 */ 104#define CONFIG_SYS_SDRAM_CFG (SDRAM_CFG_SREN \ 105 | SDRAM_CFG_SDRAM_TYPE_DDR2 \ 106 | SDRAM_CFG_DBW_32) 107 /* 0x43080000 */ 108#define CONFIG_SYS_SDRAM_CFG2 0x00401000 109#define CONFIG_SYS_DDR_MODE ((0x4440 << SDRAM_MODE_ESD_SHIFT) \ 110 | (0x0232 << SDRAM_MODE_SD_SHIFT)) 111 /* 0x44400232 */ 112#define CONFIG_SYS_DDR_MODE_2 0x8000C000 113 114#define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 115 /*0x02000000*/ 116#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ 117 | DDRCDR_PZ_NOMZ \ 118 | DDRCDR_NZ_NOMZ \ 119 | DDRCDR_M_ODR) 120 /* 0x73000002 */ 121 122/* 123 * FLASH on the Local Bus 124 */ 125#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ 126#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ 127#define CONFIG_SYS_FLASH_BASE 0xFE000000 128#define CONFIG_SYS_FLASH_SIZE 32 /* size in MB */ 129#define CONFIG_SYS_FLASH_EMPTY_INFO /* display empty sectors */ 130#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* buffer up multiple bytes */ 131 132#define CONFIG_SYS_NOR_BR_PRELIM (CONFIG_SYS_FLASH_BASE \ 133 | BR_PS_16 /* 16 bit */ \ 134 | BR_MS_GPCM /* MSEL = GPCM */ \ 135 | BR_V) /* valid */ 136#define CONFIG_SYS_NOR_OR_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ 137 | OR_GPCM_CSNT \ 138 | OR_GPCM_ACS_DIV4 \ 139 | OR_GPCM_SCY_5 \ 140 | OR_GPCM_TRLX_SET \ 141 | OR_GPCM_EAD) 142 /* 0xfe000c55 */ 143 144#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 145#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32MB) 146 147#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 148#define CONFIG_SYS_MAX_FLASH_SECT 256 /* sectors per dev */ 149 150#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 151#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 152 153#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 154 155#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) 156#define CONFIG_SYS_RAMBOOT 157#endif 158 159#define CONFIG_SYS_INIT_RAM_LOCK 1 160#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */ 161#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/ 162 163#define CONFIG_SYS_GBL_DATA_OFFSET \ 164 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 165#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 166 167/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */ 168#define CONFIG_SYS_MONITOR_LEN (384 * 1024) 169#define CONFIG_SYS_MALLOC_LEN (512 * 1024) 170 171/* 172 * Local Bus LCRR and LBCR regs 173 */ 174#define CONFIG_SYS_LCRR_EADC LCRR_EADC_3 175#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 176 177#define CONFIG_SYS_LBC_LBCR 0x00040000 178 179#define CONFIG_SYS_LBC_MRTPR 0x20000000 180 181/* 182 * NAND settings 183 */ 184#define CONFIG_SYS_NAND_BASE 0x61000000 185#define CONFIG_SYS_MAX_NAND_DEVICE 1 186#define CONFIG_MTD_NAND_VERIFY_WRITE 187#define CONFIG_CMD_NAND 1 188#define CONFIG_NAND_FSL_ELBC 1 189#define CONFIG_SYS_NAND_BLOCK_SIZE 16384 190 191#define CONFIG_SYS_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE \ 192 | BR_PS_8 \ 193 | BR_DECC_CHK_GEN \ 194 | BR_MS_FCM \ 195 | BR_V) /* valid */ 196 /* 0x61000c21 */ 197#define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_32KB \ 198 | OR_FCM_BCTLD \ 199 | OR_FCM_CHT \ 200 | OR_FCM_SCY_2 \ 201 | OR_FCM_RST \ 202 | OR_FCM_TRLX) 203 /* 0xffff90ac */ 204 205#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM 206#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM 207#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM 208#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM 209 210#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE 211#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) 212 213#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM 214#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM 215 216/* CS2 NvRAM */ 217#define CONFIG_SYS_BR2_PRELIM (0x60000000 \ 218 | BR_PS_8 \ 219 | BR_V) 220 /* 0x60000801 */ 221#define CONFIG_SYS_OR2_PRELIM (OR_AM_128KB \ 222 | OR_GPCM_CSNT \ 223 | OR_GPCM_XACS \ 224 | OR_GPCM_SCY_3 \ 225 | OR_GPCM_TRLX_SET \ 226 | OR_GPCM_EHTR_SET \ 227 | OR_GPCM_EAD) 228 /* 0xfffe0937 */ 229/* local bus read write buffer mapping SRAM@0x64000000 */ 230#define CONFIG_SYS_BR3_PRELIM (0x62000000 \ 231 | BR_PS_16 \ 232 | BR_V) 233 /* 0x62001001 */ 234 235#define CONFIG_SYS_OR3_PRELIM (OR_AM_32MB \ 236 | OR_GPCM_CSNT \ 237 | OR_GPCM_XACS \ 238 | OR_GPCM_SCY_15 \ 239 | OR_GPCM_TRLX_SET \ 240 | OR_GPCM_EHTR_SET \ 241 | OR_GPCM_EAD) 242 /* 0xfe0009f7 */ 243 244/* pass open firmware flat tree */ 245#define CONFIG_OF_LIBFDT 1 246#define CONFIG_OF_BOARD_SETUP 1 247#define CONFIG_OF_STDOUT_VIA_ALIAS 1 248 249/* 250 * Serial Port 251 */ 252#define CONFIG_CONS_INDEX 1 253#define CONFIG_SYS_NS16550 254#define CONFIG_SYS_NS16550_SERIAL 255#define CONFIG_SYS_NS16550_REG_SIZE 1 256#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 257 258#define CONFIG_SYS_BAUDRATE_TABLE \ 259 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 260 261#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) 262#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) 263 264/* Use the HUSH parser */ 265#define CONFIG_SYS_HUSH_PARSER 266 267#if defined(CONFIG_PCI) 268/* 269 * General PCI 270 * Addresses are mapped 1-1. 271 */ 272#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 273#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE 274#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ 275#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 276#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE 277#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ 278#define CONFIG_SYS_PCI1_IO_BASE 0x00000000 279#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000 280#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ 281 282#define CONFIG_PCI_PNP /* do pci plug-and-play */ 283#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 284#endif 285 286/* 287 * TSEC 288 */ 289#define CONFIG_TSEC_ENET /* TSEC ethernet support */ 290 291 292#define CONFIG_TSEC1 293#ifdef CONFIG_TSEC1 294#define CONFIG_HAS_ETH0 295#define CONFIG_TSEC1_NAME "TSEC1" 296#define CONFIG_SYS_TSEC1_OFFSET 0x24000 297#define TSEC1_PHY_ADDR 0x01 298#define TSEC1_FLAGS 0 299#define TSEC1_PHYIDX 0 300#endif 301 302/* Options are: TSEC[0-1] */ 303#define CONFIG_ETHPRIME "TSEC1" 304 305/* 306 * Environment 307 */ 308#define CONFIG_ENV_IS_IN_FLASH 1 309#define CONFIG_ENV_ADDR \ 310 (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN) 311#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ 312#define CONFIG_ENV_SIZE 0x4000 313/* Address and size of Redundant Environment Sector */ 314#define CONFIG_ENV_OFFSET_REDUND \ 315 (CONFIG_ENV_OFFSET + CONFIG_ENV_SECT_SIZE) 316#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) 317 318#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 319#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 320 321/* 322 * BOOTP options 323 */ 324#define CONFIG_BOOTP_BOOTFILESIZE 325#define CONFIG_BOOTP_BOOTPATH 326#define CONFIG_BOOTP_GATEWAY 327#define CONFIG_BOOTP_HOSTNAME 328 329/* 330 * Command line configuration. 331 */ 332#include <config_cmd_default.h> 333 334#define CONFIG_CMD_DHCP 335#define CONFIG_CMD_MII 336#define CONFIG_CMD_PING 337#define CONFIG_CMD_PCI 338 339#define CONFIG_CMDLINE_EDITING 1 340#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 341 342/* 343 * Miscellaneous configurable options 344 */ 345#define CONFIG_SYS_LONGHELP /* undef to save memory */ 346#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ 347#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 348 349#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 350#define CONFIG_SYS_MAXARGS 16 /* max number of cmd args */ 351#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot arg Buffer size */ 352 353/* 354 * For booting Linux, the board info and command line data 355 * have to be in the first 256 MB of memory, since this is 356 * the maximum mapped by the Linux kernel during initialization. 357 */ 358 /* Initial Memory map for Linux*/ 359#define CONFIG_SYS_BOOTMAPSZ (256 << 20) 360 361/* 0x64050000 */ 362#define CONFIG_SYS_HRCW_LOW (\ 363 0x20000000 /* reserved, must be set */ |\ 364 HRCWL_DDRCM |\ 365 HRCWL_CSB_TO_CLKIN_4X1 | \ 366 HRCWL_CORE_TO_CSB_2_5X1) 367 368/* 0xa0600004 */ 369#define CONFIG_SYS_HRCW_HIGH (HRCWH_PCI_HOST | \ 370 HRCWH_PCI_ARBITER_ENABLE | \ 371 HRCWH_CORE_ENABLE | \ 372 HRCWH_FROM_0X00000100 | \ 373 HRCWH_BOOTSEQ_DISABLE |\ 374 HRCWH_SW_WATCHDOG_DISABLE |\ 375 HRCWH_ROM_LOC_LOCAL_16BIT | \ 376 HRCWH_TSEC1M_IN_MII | \ 377 HRCWH_BIG_ENDIAN | \ 378 HRCWH_LALE_EARLY) 379 380/* System IO Config */ 381#define CONFIG_SYS_SICRH (0x01000000 | \ 382 SICRH_ETSEC2_B | \ 383 SICRH_ETSEC2_C | \ 384 SICRH_ETSEC2_D | \ 385 SICRH_ETSEC2_E | \ 386 SICRH_ETSEC2_F | \ 387 SICRH_ETSEC2_G | \ 388 SICRH_TSOBI1 | \ 389 SICRH_TSOBI2) 390 /* 0x010fff03 */ 391#define CONFIG_SYS_SICRL (SICRL_LBC | \ 392 SICRL_SPI_A | \ 393 SICRL_SPI_B | \ 394 SICRL_SPI_C | \ 395 SICRL_SPI_D | \ 396 SICRL_ETSEC2_A) 397 /* 0x33fc0003) */ 398 399#define CONFIG_SYS_HID0_INIT 0x000000000 400#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ 401 HID0_ENABLE_INSTRUCTION_CACHE) 402 403#define CONFIG_SYS_HID2 HID2_HBE 404 405#define CONFIG_HIGH_BATS 1 /* High BATs supported */ 406 407/* DDR @ 0x00000000 */ 408#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW) 409#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \ 410 | BATU_BL_256M \ 411 | BATU_VS \ 412 | BATU_VP) 413 414#if defined(CONFIG_PCI) 415/* PCI @ 0x80000000 */ 416#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_RW) 417#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE \ 418 | BATU_BL_256M \ 419 | BATU_VS \ 420 | BATU_VP) 421#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE \ 422 | BATL_PP_RW \ 423 | BATL_CACHEINHIBIT \ 424 | BATL_GUARDEDSTORAGE) 425#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE \ 426 | BATU_BL_256M \ 427 | BATU_VS \ 428 | BATU_VP) 429#else 430#define CONFIG_SYS_IBAT1L (0) 431#define CONFIG_SYS_IBAT1U (0) 432#define CONFIG_SYS_IBAT2L (0) 433#define CONFIG_SYS_IBAT2U (0) 434#endif 435 436/* PCI2 not supported on 8313 */ 437#define CONFIG_SYS_IBAT3L (0) 438#define CONFIG_SYS_IBAT3U (0) 439#define CONFIG_SYS_IBAT4L (0) 440#define CONFIG_SYS_IBAT4U (0) 441 442/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */ 443#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR \ 444 | BATL_PP_RW \ 445 | BATL_CACHEINHIBIT \ 446 | BATL_GUARDEDSTORAGE) 447#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR \ 448 | BATU_BL_256M \ 449 | BATU_VS \ 450 | BATU_VP) 451 452/* stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */ 453#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_RW | BATL_GUARDEDSTORAGE) 454#define CONFIG_SYS_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) 455 456/* FPGA, SRAM, NAND @ 0x60000000 */ 457#define CONFIG_SYS_IBAT7L (0x60000000 | BATL_PP_RW | BATL_GUARDEDSTORAGE) 458#define CONFIG_SYS_IBAT7U (0x60000000 | BATU_BL_256M | BATU_VS | BATU_VP) 459 460#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 461#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 462#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 463#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 464#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L 465#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 466#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L 467#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 468#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L 469#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U 470#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L 471#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U 472#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L 473#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U 474#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L 475#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U 476 477#define CONFIG_NETDEV eth0 478 479#define CONFIG_HOSTNAME ve8313 480#define CONFIG_UBOOTPATH ve8313/u-boot.bin 481 482#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ 483#define CONFIG_BAUDRATE 115200 484 485#define CONFIG_EXTRA_ENV_SETTINGS \ 486 "netdev=" __stringify(CONFIG_NETDEV) "\0" \ 487 "ethprime=" __stringify(CONFIG_TSEC1_NAME) "\0" \ 488 "u-boot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 489 "u-boot_addr_r=100000\0" \ 490 "load=tftp ${u-boot_addr_r} ${u-boot}\0" \ 491 "update=protect off " __stringify(CONFIG_SYS_FLASH_BASE) \ 492 " +${filesize};" \ 493 "erase " __stringify(CONFIG_SYS_FLASH_BASE) " +${filesize};" \ 494 "cp.b ${u-boot_addr_r} " __stringify(CONFIG_SYS_FLASH_BASE) \ 495 " ${filesize};" \ 496 "protect on " __stringify(CONFIG_SYS_FLASH_BASE) " +${filesize}\0" \ 497 498#endif /* __CONFIG_H */ 499