LXR uboot/board/congatec/cgtqmx6eval/cgtqmx6eval.c

   1/*
   2 * Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
   3 * Based on mx6qsabrelite.c file
   4 * Copyright (C) 2013, Adeneo Embedded <www.adeneo-embedded.com>
   5 * Leo Sartre, <lsartre@adeneo-embedded.com>
   6 *
   7 * SPDX-License-Identifier:     GPL-2.0+
   8 */
   9
  10#include <common.h>
  11#include <asm/io.h>
  12#include <asm/arch/clock.h>
  13#include <asm/arch/imx-regs.h>
  14#include <asm/arch/iomux.h>
  15#include <asm/arch/mx6-pins.h>
  16#include <asm/gpio.h>
  17#include <asm/imx-common/iomux-v3.h>
  18#include <asm/imx-common/boot_mode.h>
  19#include <mmc.h>
  20#include <fsl_esdhc.h>
  21
  22DECLARE_GLOBAL_DATA_PTR;
  23
  24#define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |\
  25        PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  26
  27#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP  | PAD_CTL_SPEED_LOW |\
  28        PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  29
  30int dram_init(void)
  31{
  32        gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
  33
  34        return 0;
  35}
  36
  37iomux_v3_cfg_t const uart2_pads[] = {
  38        MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
  39        MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
  40};
  41
  42iomux_v3_cfg_t const usdhc2_pads[] = {
  43        MX6_PAD_SD2_CLK__SD2_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  44        MX6_PAD_SD2_CMD__SD2_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  45        MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  46        MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  47        MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  48        MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  49        MX6_PAD_GPIO_4__GPIO1_IO04      | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  50};
  51
  52iomux_v3_cfg_t const usdhc4_pads[] = {
  53        MX6_PAD_SD4_CLK__SD4_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  54        MX6_PAD_SD4_CMD__SD4_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  55        MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  56        MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  57        MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  58        MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  59        MX6_PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  60        MX6_PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  61        MX6_PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  62        MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  63        MX6_PAD_NANDF_D6__GPIO2_IO06    | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
  64};
  65
  66static void setup_iomux_uart(void)
  67{
  68        imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
  69}
  70
  71#ifdef CONFIG_FSL_ESDHC
  72struct fsl_esdhc_cfg usdhc_cfg[] = {
  73        {USDHC2_BASE_ADDR},
  74        {USDHC4_BASE_ADDR},
  75};
  76
  77int board_mmc_getcd(struct mmc *mmc)
  78{
  79        struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
  80        int ret = 0;
  81
  82        switch (cfg->esdhc_base) {
  83        case USDHC2_BASE_ADDR:
  84                gpio_direction_input(IMX_GPIO_NR(1, 4));
  85                ret = !gpio_get_value(IMX_GPIO_NR(1, 4));
  86                break;
  87        case USDHC4_BASE_ADDR:
  88                gpio_direction_input(IMX_GPIO_NR(2, 6));
  89                ret = !gpio_get_value(IMX_GPIO_NR(2, 6));
  90                break;
  91        default:
  92                printf("Bad USDHC interface\n");
  93        }
  94
  95        return ret;
  96}
  97
  98int board_mmc_init(bd_t *bis)
  99{
 100        s32 status = 0;
 101
 102        usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
 103        usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
 104
 105        imx_iomux_v3_setup_multiple_pads(
 106                                usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
 107        imx_iomux_v3_setup_multiple_pads(
 108                                usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
 109
 110        status = fsl_esdhc_initialize(bis, &usdhc_cfg[0]) |
 111                     fsl_esdhc_initialize(bis, &usdhc_cfg[1]);
 112
 113        return status;
 114}
 115#endif
 116
 117int board_early_init_f(void)
 118{
 119        setup_iomux_uart();
 120
 121        return 0;
 122}
 123
 124int board_init(void)
 125{
 126        /* address of boot parameters */
 127        gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
 128
 129        return 0;
 130}
 131
 132int checkboard(void)
 133{
 134        puts("Board: Conga-QEVAL QMX6 Quad\n");
 135
 136        return 0;
 137}
 138
 139#ifdef CONFIG_CMD_BMODE
 140static const struct boot_mode board_boot_modes[] = {
 141        /* 4 bit bus width */
 142        {"mmc0",        MAKE_CFGVAL(0x50, 0x20, 0x00, 0x00)},
 143        {"mmc1",        MAKE_CFGVAL(0x50, 0x38, 0x00, 0x00)},
 144        {NULL,          0},
 145};
 146#endif
 147
 148int misc_init_r(void)
 149{
 150#ifdef CONFIG_CMD_BMODE
 151        add_board_boot_modes(board_boot_modes);
 152#endif
 153        return 0;
 154}
 155