/*
 * (C) Copyright 2014
 * Dirk Eibach,  Guntermann & Drunck GmbH, eibach@gdsys.de
 *
 *
 * SPDX-License-Identifier:     GPL-2.0+
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * High Level Configuration Options
 */
#define CONFIG_E300             1 /* E300 family */
#define CONFIG_MPC83xx          1 /* MPC83xx family */
#define CONFIG_MPC830x          1 /* MPC830x family */
#define CONFIG_MPC8308          1 /* MPC8308 CPU specific */
#define CONFIG_HRCON            1 /* HRCON board specific */

#define CONFIG_SYS_TEXT_BASE    0xFE000000

#define CONFIG_IDENT_STRING     " hrcon 0.01"

#define CONFIG_SYS_GENERIC_BOARD

#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_EARLY_INIT_R
#define CONFIG_LAST_STAGE_INIT

/* new uImage format support */
#define CONFIG_FIT                      1
#define CONFIG_FIT_VERBOSE              1

#define CONFIG_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC83xx_ESDHC_ADDR
#define CONFIG_SYS_FSL_ERRATUM_ESDHC111

#define CONFIG_CMD_MMC
#define CONFIG_GENERIC_MMC
#define CONFIG_DOS_PARTITION
#define CONFIG_CMD_EXT2

#define CONFIG_CMD_FPGAD
#define CONFIG_CMD_IOLOOP

/*
 * System Clock Setup
 */
#define CONFIG_83XX_CLKIN       33333333 /* in Hz */
#define CONFIG_SYS_CLK_FREQ     CONFIG_83XX_CLKIN

/*
 * Hardware Reset Configuration Word
 * if CLKIN is 66.66MHz, then
 * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
 * We choose the A type silicon as default, so the core is 400Mhz.
 */
#define CONFIG_SYS_HRCW_LOW (\
        HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
        HRCWL_DDR_TO_SCB_CLK_2X1 |\
        HRCWL_SVCOD_DIV_2 |\
        HRCWL_CSB_TO_CLKIN_4X1 |\
        HRCWL_CORE_TO_CSB_3X1)
/*
 * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
 * in 8308's HRCWH according to the manual, but original Freescale's
 * code has them and I've expirienced some problems using the board
 * with BDI3000 attached when I've tried to set these bits to zero
 * (UART doesn't work after the 'reset run' command).
 */
#define CONFIG_SYS_HRCW_HIGH (\
        HRCWH_PCI_HOST |\
        HRCWH_PCI1_ARBITER_ENABLE |\
        HRCWH_CORE_ENABLE |\
        HRCWH_FROM_0XFFF00100 |\
        HRCWH_BOOTSEQ_DISABLE |\
        HRCWH_SW_WATCHDOG_DISABLE |\
        HRCWH_ROM_LOC_LOCAL_16BIT |\
        HRCWH_RL_EXT_LEGACY |\
        HRCWH_TSEC1M_IN_RGMII |\
        HRCWH_TSEC2M_IN_RGMII |\
        HRCWH_BIG_ENDIAN)

/*
 * System IO Config
 */
#define CONFIG_SYS_SICRH (\
        SICRH_ESDHC_A_SD |\
        SICRH_ESDHC_B_SD |\
        SICRH_ESDHC_C_SD |\
        SICRH_GPIO_A_GPIO |\
        SICRH_GPIO_B_GPIO |\
        SICRH_IEEE1588_A_GPIO |\
        SICRH_USB |\
        SICRH_GTM_GPIO |\
        SICRH_IEEE1588_B_GPIO |\
        SICRH_ETSEC2_GPIO |\
        SICRH_GPIOSEL_1 |\
        SICRH_TMROBI_V3P3 |\
        SICRH_TSOBI1_V2P5 |\
        SICRH_TSOBI2_V2P5)      /* 0x0037f103 */
#define CONFIG_SYS_SICRL (\
        SICRL_SPI_PF0 |\
        SICRL_UART_PF0 |\
        SICRL_IRQ_PF0 |\
        SICRL_I2C2_PF0 |\
        SICRL_ETSEC1_GTX_CLK125)        /* 0x00000000 */

/*
 * IMMR new address
 */
#define CONFIG_SYS_IMMR         0xE0000000

/*
 * SERDES
 */
#define CONFIG_FSL_SERDES
#define CONFIG_FSL_SERDES1      0xe3000

/*
 * Arbiter Setup
 */
#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */
#define CONFIG_SYS_ACR_RPTCNT   3 /* Arbiter repeat count is 4 */
#define CONFIG_SYS_SPCR_TSECEP  3 /* eTSEC emergency priority is highest */

/*
 * DDR Setup
 */
#define CONFIG_SYS_DDR_BASE             0x00000000 /* DDR is system memory */
#define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE       CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
                                | DDRCDR_PZ_LOZ \
                                | DDRCDR_NZ_LOZ \
                                | DDRCDR_ODT \
                                | DDRCDR_Q_DRN)
                                /* 0x7b880001 */
/*
 * Manually set up DDR parameters
 * consist of one chip NT5TU64M16HG from NANYA
 */

#define CONFIG_SYS_DDR_SIZE             128 /* MB */

#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
#define CONFIG_SYS_DDR_CS0_CONFIG       (CSCONFIG_EN \
                                | CSCONFIG_ODT_RD_NEVER \
                                | CSCONFIG_ODT_WR_ONLY_CURRENT \
                                | CSCONFIG_BANK_BIT_3 \
                                | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
                                /* 0x80010102 */
#define CONFIG_SYS_DDR_TIMING_3 0
#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
                                | (0 << TIMING_CFG0_WRT_SHIFT) \
                                | (0 << TIMING_CFG0_RRT_SHIFT) \
                                | (0 << TIMING_CFG0_WWT_SHIFT) \
                                | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
                                | (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
                                | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
                                | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
                                /* 0x00260802 */
#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
                                | (6 << TIMING_CFG1_ACTTOPRE_SHIFT) \
                                | (2 << TIMING_CFG1_ACTTORW_SHIFT) \
                                | (7 << TIMING_CFG1_CASLAT_SHIFT) \
                                | (9 << TIMING_CFG1_REFREC_SHIFT) \
                                | (2 << TIMING_CFG1_WRREC_SHIFT) \
                                | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
                                | (2 << TIMING_CFG1_WRTORD_SHIFT))
                                /* 0x26279222 */
#define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \
                                | (4 << TIMING_CFG2_CPO_SHIFT) \
                                | (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
                                | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
                                | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
                                | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
                                | (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
                                /* 0x021848c5 */
#define CONFIG_SYS_DDR_INTERVAL ((0x0824 << SDRAM_INTERVAL_REFINT_SHIFT) \
                                | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
                                /* 0x08240100 */
#define CONFIG_SYS_DDR_SDRAM_CFG        (SDRAM_CFG_SREN \
                                | SDRAM_CFG_SDRAM_TYPE_DDR2 \
                                | SDRAM_CFG_DBW_16)
                                /* 0x43100000 */

#define CONFIG_SYS_DDR_SDRAM_CFG2       0x00401000 /* 1 posted refresh */
#define CONFIG_SYS_DDR_MODE             ((0x0440 << SDRAM_MODE_ESD_SHIFT) \
                                | (0x0242 << SDRAM_MODE_SD_SHIFT))
                                /* ODT 150ohm CL=4, AL=0 on SDRAM */
#define CONFIG_SYS_DDR_MODE2            0x00000000

/*
 * Memory test
 */
#define CONFIG_SYS_MEMTEST_START        0x00001000 /* memtest region */
#define CONFIG_SYS_MEMTEST_END          0x07f00000

/*
 * The reserved memory
 */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */

#define CONFIG_SYS_MONITOR_LEN  (384 * 1024) /* Reserve 384 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN   (512 * 1024) /* Reserved for malloc */

/*
 * Initial RAM Base Address Setup
 */
#define CONFIG_SYS_INIT_RAM_LOCK        1
#define CONFIG_SYS_INIT_RAM_ADDR        0xE6000000 /* Initial RAM address */
#define CONFIG_SYS_INIT_RAM_SIZE        0x1000 /* Size of used area in RAM */
#define CONFIG_SYS_GBL_DATA_OFFSET      \
        (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)

/*
 * Local Bus Configuration & Clock Setup
 */
#define CONFIG_SYS_LCRR_DBYP            LCRR_DBYP
#define CONFIG_SYS_LCRR_CLKDIV          LCRR_CLKDIV_2
#define CONFIG_SYS_LBC_LBCR             0x00040000

/*
 * FLASH on the Local Bus
 */
#if 1
#define CONFIG_SYS_FLASH_CFI            /* use the Common Flash Interface */
#define CONFIG_FLASH_CFI_DRIVER         /* use the CFI driver */
#define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_16BIT
#define CONFIG_FLASH_CFI_LEGACY
#define CONFIG_SYS_FLASH_LEGACY_512Kx16
#else
#define CONFIG_SYS_NO_FLASH
#endif

#define CONFIG_SYS_FLASH_BASE           0xFE000000 /* FLASH base address */
#define CONFIG_SYS_FLASH_SIZE           8 /* FLASH size is up to 8M */
#define CONFIG_SYS_FLASH_PROTECTION     1 /* Use h/w Flash protection. */

/* Window base at flash base */
#define CONFIG_SYS_LBLAWBAR0_PRELIM     CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_LBLAWAR0_PRELIM      (LBLAWAR_EN | LBLAWAR_8MB)

#define CONFIG_SYS_BR0_PRELIM   (CONFIG_SYS_FLASH_BASE \
                                | BR_PS_16      /* 16 bit port */ \
                                | BR_MS_GPCM    /* MSEL = GPCM */ \
                                | BR_V)         /* valid */
#define CONFIG_SYS_OR0_PRELIM   (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
                                | OR_UPM_XAM \
                                | OR_GPCM_CSNT \
                                | OR_GPCM_ACS_DIV2 \
                                | OR_GPCM_XACS \
                                | OR_GPCM_SCY_15 \
                                | OR_GPCM_TRLX_SET \
                                | OR_GPCM_EHTR_SET)

#define CONFIG_SYS_MAX_FLASH_BANKS      1 /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT       135

#define CONFIG_SYS_FLASH_ERASE_TOUT     60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT     500 /* Flash Write Timeout (ms) */

/*
 * FPGA
 */
#define CONFIG_SYS_FPGA0_BASE           0xE0600000
#define CONFIG_SYS_FPGA0_SIZE           1 /* FPGA size is 1M */

/* Window base at FPGA base */
#define CONFIG_SYS_LBLAWBAR1_PRELIM     CONFIG_SYS_FPGA0_BASE
#define CONFIG_SYS_LBLAWAR1_PRELIM      (LBLAWAR_EN | LBLAWAR_1MB)

#define CONFIG_SYS_BR1_PRELIM   (CONFIG_SYS_FPGA0_BASE \
                                | BR_PS_16      /* 16 bit port */ \
                                | BR_MS_GPCM    /* MSEL = GPCM */ \
                                | BR_V)         /* valid */
#define CONFIG_SYS_OR1_PRELIM   (MEG_TO_AM(CONFIG_SYS_FPGA0_SIZE) \
                                | OR_UPM_XAM \
                                | OR_GPCM_CSNT \
                                | OR_GPCM_ACS_DIV2 \
                                | OR_GPCM_XACS \
                                | OR_GPCM_SCY_15 \
                                | OR_GPCM_TRLX_SET \
                                | OR_GPCM_EHTR_SET)

#define CONFIG_SYS_FPGA_BASE(k)         CONFIG_SYS_FPGA0_BASE
#define CONFIG_SYS_FPGA_DONE(k)         0x0010

#define CONFIG_SYS_FPGA_COUNT           1

#define CONFIG_SYS_MCLINK_MAX           3

#define CONFIG_SYS_FPGA_PTR \
        { (struct ihs_fpga *)CONFIG_SYS_FPGA0_BASE, NULL, NULL, NULL }

/*
 * Serial Port
 */
#define CONFIG_CONS_INDEX       2
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE     1
#define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)

#define CONFIG_SYS_BAUDRATE_TABLE  \
        {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)

/* Use the HUSH parser */
#define CONFIG_SYS_HUSH_PARSER

/* Pass open firmware flat tree */
#define CONFIG_OF_LIBFDT                1
#define CONFIG_OF_BOARD_SETUP           1
#define CONFIG_OF_STDOUT_VIA_ALIAS      1

/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED        400000
#define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET       0x3000

#define CONFIG_PCA953X                  /* NXP PCA9554 */
#define CONFIG_PCA9698                  /* NXP PCA9698 */

#define CONFIG_SYS_I2C_IHS
#define CONFIG_SYS_I2C_IHS_CH0
#define CONFIG_SYS_I2C_IHS_SPEED_0              50000
#define CONFIG_SYS_I2C_IHS_SLAVE_0              0x7F
#define CONFIG_SYS_I2C_IHS_CH1
#define CONFIG_SYS_I2C_IHS_SPEED_1              50000
#define CONFIG_SYS_I2C_IHS_SLAVE_1              0x7F
#define CONFIG_SYS_I2C_IHS_CH2
#define CONFIG_SYS_I2C_IHS_SPEED_2              50000
#define CONFIG_SYS_I2C_IHS_SLAVE_2              0x7F
#define CONFIG_SYS_I2C_IHS_CH3
#define CONFIG_SYS_I2C_IHS_SPEED_3              50000
#define CONFIG_SYS_I2C_IHS_SLAVE_3              0x7F

/*
 * Software (bit-bang) I2C driver configuration
 */
#define CONFIG_SYS_I2C_SOFT
#define CONFIG_SYS_I2C_SOFT_SPEED               50000
#define CONFIG_SYS_I2C_SOFT_SLAVE               0x7F
#define I2C_SOFT_DECLARATIONS2
#define CONFIG_SYS_I2C_SOFT_SPEED_2             50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_2             0x7F
#define I2C_SOFT_DECLARATIONS3
#define CONFIG_SYS_I2C_SOFT_SPEED_3             50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_3             0x7F
#define I2C_SOFT_DECLARATIONS4
#define CONFIG_SYS_I2C_SOFT_SPEED_4             50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_4             0x7F

#define CONFIG_SYS_ICS8N3QV01_I2C               {5, 6, 7, 8}
#define CONFIG_SYS_CH7301_I2C                   {5, 6, 7, 8}
#define CONFIG_SYS_DP501_I2C                    {1, 2, 3, 4}

#ifndef __ASSEMBLY__
void fpga_gpio_set(unsigned int bus, int pin);
void fpga_gpio_clear(unsigned int bus, int pin);
int fpga_gpio_get(unsigned int bus, int pin);
#endif

#define I2C_ACTIVE      { }
#define I2C_TRISTATE    { }
#define I2C_READ \
        (fpga_gpio_get(I2C_ADAP_HWNR, 0x0040) ? 1 : 0)
#define I2C_SDA(bit) \
        do { \
                if (bit) \
                        fpga_gpio_set(I2C_ADAP_HWNR, 0x0040); \
                else \
                        fpga_gpio_clear(I2C_ADAP_HWNR, 0x0040); \
        } while (0)
#define I2C_SCL(bit) \
        do { \
                if (bit) \
                        fpga_gpio_set(I2C_ADAP_HWNR, 0x0020); \
                else \
                        fpga_gpio_clear(I2C_ADAP_HWNR, 0x0020); \
        } while (0)
#define I2C_DELAY       udelay(25)      /* 1/4 I2C clock duration */

/*
 * Software (bit-bang) MII driver configuration
 */
#define CONFIG_BITBANGMII               /* bit-bang MII PHY management */
#define CONFIG_BITBANGMII_MULTI

/*
 * OSD Setup
 */
#define CONFIG_SYS_OSD_SCREENS          1
#define CONFIG_SYS_DP501_DIFFERENTIAL
#define CONFIG_SYS_DP501_VCAPCTRL0      0x01 /* DDR mode 0, DE for H/VSYNC */

/*
 * General PCI
 * Addresses are mapped 1-1.
 */
#define CONFIG_SYS_PCIE1_BASE           0xA0000000
#define CONFIG_SYS_PCIE1_MEM_BASE       0xA0000000
#define CONFIG_SYS_PCIE1_MEM_PHYS       0xA0000000
#define CONFIG_SYS_PCIE1_MEM_SIZE       0x10000000
#define CONFIG_SYS_PCIE1_CFG_BASE       0xB0000000
#define CONFIG_SYS_PCIE1_CFG_SIZE       0x01000000
#define CONFIG_SYS_PCIE1_IO_BASE        0x00000000
#define CONFIG_SYS_PCIE1_IO_PHYS        0xB1000000
#define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000

/* enable PCIE clock */
#define CONFIG_SYS_SCCR_PCIEXP1CM       1

#define CONFIG_PCI
#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_PCIE

#define CONFIG_PCI_PNP          /* do pci plug-and-play */

#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957   /* Freescale */
#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1

/*
 * TSEC
 */
#define CONFIG_TSEC_ENET        /* TSEC ethernet support */
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
#define CONFIG_SYS_TSEC1        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)

/*
 * TSEC ethernet configuration
 */
#define CONFIG_MII              1 /* MII PHY management */
#define CONFIG_TSEC1
#define CONFIG_TSEC1_NAME       "eTSEC0"
#define TSEC1_PHY_ADDR          1
#define TSEC1_PHYIDX            0
#define TSEC1_FLAGS             TSEC_GIGABIT

/* Options are: eTSEC[0-1] */
#define CONFIG_ETHPRIME         "eTSEC0"

/*
 * Environment
 */
#if 1
#define CONFIG_ENV_IS_IN_FLASH  1
#define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + \
                                 CONFIG_SYS_MONITOR_LEN)
#define CONFIG_ENV_SECT_SIZE    0x10000 /* 64K(one sector) for env */
#define CONFIG_ENV_SIZE         0x2000
#define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND  CONFIG_ENV_SIZE
#else
#define CONFIG_ENV_IS_NOWHERE
#define CONFIG_ENV_SIZE         0x2000          /* 8KB */
#endif

#define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */

/*
 * Command line configuration.
 */
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
#define CONFIG_CMD_PCI
#define CONFIG_CMD_PING

#define CONFIG_CMDLINE_EDITING  1       /* add command line history */
#define CONFIG_AUTO_COMPLETE            /* add autocompletion support */

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP             /* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR            0x2000000 /* default load address */
#define CONFIG_SYS_PROMPT               "=> "   /* Monitor Command Prompt */
#define CONFIG_SYS_HZ           1000    /* decrementer freq: 1ms ticks */

#undef CONFIG_ZERO_BOOTDELAY_CHECK      /* ignore keypress on bootdelay==0 */

#define CONFIG_SYS_CBSIZE       1024 /* Console I/O Buffer Size */

#define CONFIG_SYS_CONSOLE_INFO_QUIET

/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS      16      /* max number of command args */
#define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 256 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ    (256 << 20) /* Initial Memory map for Linux */

/*
 * Core HID Setup
 */
#define CONFIG_SYS_HID0_INIT    0x000000000
#define CONFIG_SYS_HID0_FINAL   (HID0_ENABLE_MACHINE_CHECK | \
                                 HID0_ENABLE_INSTRUCTION_CACHE | \
                                 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
#define CONFIG_SYS_HID2         HID2_HBE

/*
 * MMU Setup
 */

/* DDR: cache cacheable */
#define CONFIG_SYS_IBAT0L       (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
                                        BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT0U       (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
                                        BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT0L       CONFIG_SYS_IBAT0L
#define CONFIG_SYS_DBAT0U       CONFIG_SYS_IBAT0U

/* IMMRBAR, PCI IO and FPGA: cache-inhibit and guarded */
#define CONFIG_SYS_IBAT1L       (CONFIG_SYS_IMMR | BATL_PP_RW | \
                        BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT1U       (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
                                        BATU_VP)
#define CONFIG_SYS_DBAT1L       CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U       CONFIG_SYS_IBAT1U

/* FLASH: icache cacheable, but dcache-inhibit and guarded */
#define CONFIG_SYS_IBAT2L       (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
                                        BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT2U       (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
                                        BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT2L       (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
                                        BATL_CACHEINHIBIT | \
                                        BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT2U       CONFIG_SYS_IBAT2U

/* Stack in dcache: cacheable, no memory coherence */
#define CONFIG_SYS_IBAT3L       (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
#define CONFIG_SYS_IBAT3U       (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
                                        BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT3L       CONFIG_SYS_IBAT3L
#define CONFIG_SYS_DBAT3U       CONFIG_SYS_IBAT3U

/*
 * Environment Configuration
 */

#define CONFIG_ENV_OVERWRITE

#if defined(CONFIG_TSEC_ENET)
#define CONFIG_HAS_ETH0
#endif

#define CONFIG_BAUDRATE 115200

#define CONFIG_LOADADDR 800000  /* default location for tftp and bootm */

#define CONFIG_BOOTDELAY        5       /* -1 disables auto-boot */

#define CONFIG_HOSTNAME         hrcon
#define CONFIG_ROOTPATH         "/opt/nfsroot"
#define CONFIG_BOOTFILE         "uImage"

#define CONFIG_PREBOOT          /* enable preboot variable */

#define CONFIG_EXTRA_ENV_SETTINGS                                       \
        "netdev=eth0\0"                                                 \
        "consoledev=ttyS1\0"                                            \
        "u-boot=u-boot.bin\0"                                           \
        "kernel_addr=1000000\0"                                 \
        "fdt_addr=C00000\0"                                             \
        "fdtfile=hrcon.dtb\0"                           \
        "load=tftp ${loadaddr} ${u-boot}\0"                             \
        "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE)      \
                " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
                " +${filesize};cp.b ${fileaddr} "                       \
                __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0"   \
        "upd=run load update\0"                                         \

#define CONFIG_NFSBOOTCOMMAND                                           \
        "setenv bootargs root=/dev/nfs rw "                             \
        "nfsroot=$serverip:$rootpath "                                  \
        "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
        "console=$consoledev,$baudrate $othbootargs;"                   \
        "tftp ${kernel_addr} $bootfile;"                                \
        "tftp ${fdt_addr} $fdtfile;"                                    \
        "bootm ${kernel_addr} - ${fdt_addr}"

#define CONFIG_MMCBOOTCOMMAND                                           \
        "setenv bootargs root=/dev/mmcblk0p3 rw rootwait "              \
        "console=$consoledev,$baudrate $othbootargs;"                   \
        "ext2load mmc 0:2 ${kernel_addr} $bootfile;"                    \
        "ext2load mmc 0:2 ${fdt_addr} $fdtfile;"                        \
        "bootm ${kernel_addr} - ${fdt_addr}"

#define CONFIG_BOOTCOMMAND              CONFIG_MMCBOOTCOMMAND


#endif  /* __CONFIG_H */