1/* 2 * Configuation settings for the Motorola MC5282EVB board. 3 * 4 * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9/* 10 * board/config.h - configuration options, board specific 11 */ 12 13#ifndef _CONFIG_M5282EVB_H 14#define _CONFIG_M5282EVB_H 15 16/* 17 * High Level Configuration Options 18 * (easy to change) 19 */ 20#define CONFIG_MCFTMR 21 22#define CONFIG_MCFUART 23#define CONFIG_SYS_UART_PORT (0) 24#define CONFIG_BAUDRATE 115200 25 26#undef CONFIG_MONITOR_IS_IN_RAM /* define if monitor is started from a pre-loader */ 27 28/* Configuration for environment 29 * Environment is embedded in u-boot in the second sector of the flash 30 */ 31#define CONFIG_ENV_ADDR 0xffe04000 32#define CONFIG_ENV_SIZE 0x2000 33#define CONFIG_ENV_IS_IN_FLASH 1 34 35#define LDS_BOARD_TEXT \ 36 . = DEFINED(env_offset) ? env_offset : .; \ 37 common/env_embedded.o (.text*); 38 39/* 40 * BOOTP options 41 */ 42#define CONFIG_BOOTP_BOOTFILESIZE 43#define CONFIG_BOOTP_BOOTPATH 44#define CONFIG_BOOTP_GATEWAY 45#define CONFIG_BOOTP_HOSTNAME 46 47/* 48 * Command line configuration. 49 */ 50#define CONFIG_CMD_CACHE 51#define CONFIG_CMD_PING 52#define CONFIG_CMD_MII 53 54#define CONFIG_MCFFEC 55#ifdef CONFIG_MCFFEC 56# define CONFIG_MII 1 57# define CONFIG_MII_INIT 1 58# define CONFIG_SYS_DISCOVER_PHY 59# define CONFIG_SYS_RX_ETH_BUFFER 8 60# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 61 62# define CONFIG_SYS_FEC0_PINMUX 0 63# define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE 64# define MCFFEC_TOUT_LOOP 50000 65/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ 66# ifndef CONFIG_SYS_DISCOVER_PHY 67# define FECDUPLEX FULL 68# define FECSPEED _100BASET 69# else 70# ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN 71# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 72# endif 73# endif /* CONFIG_SYS_DISCOVER_PHY */ 74#endif 75 76#define CONFIG_BOOTDELAY 5 77#ifdef CONFIG_MCFFEC 78# define CONFIG_IPADDR 192.162.1.2 79# define CONFIG_NETMASK 255.255.255.0 80# define CONFIG_SERVERIP 192.162.1.1 81# define CONFIG_GATEWAYIP 192.162.1.1 82#endif /* CONFIG_MCFFEC */ 83 84#define CONFIG_HOSTNAME M5282EVB 85#define CONFIG_EXTRA_ENV_SETTINGS \ 86 "netdev=eth0\0" \ 87 "loadaddr=10000\0" \ 88 "u-boot=u-boot.bin\0" \ 89 "load=tftp ${loadaddr) ${u-boot}\0" \ 90 "upd=run load; run prog\0" \ 91 "prog=prot off ffe00000 ffe3ffff;" \ 92 "era ffe00000 ffe3ffff;" \ 93 "cp.b ${loadaddr} ffe00000 ${filesize};"\ 94 "save\0" \ 95 "" 96 97#define CONFIG_SYS_LONGHELP /* undef to save memory */ 98 99#if defined(CONFIG_CMD_KGDB) 100#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 101#else 102#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 103#endif 104#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 105#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 106#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 107 108#define CONFIG_SYS_LOAD_ADDR 0x20000 109 110#define CONFIG_SYS_MEMTEST_START 0x400 111#define CONFIG_SYS_MEMTEST_END 0x380000 112 113#define CONFIG_SYS_CLK 64000000 114 115/* PLL Configuration: Ext Clock * 6 (see table 9-4 of MCF user manual) */ 116 117#define CONFIG_SYS_MFD 0x02 /* PLL Multiplication Factor Devider */ 118#define CONFIG_SYS_RFD 0x00 /* PLL Reduce Frecuency Devider */ 119 120/* 121 * Low Level Configuration Settings 122 * (address mappings, register initial values, etc.) 123 * You should know what you are doing if you make changes here. 124 */ 125#define CONFIG_SYS_MBAR 0x40000000 126 127/*----------------------------------------------------------------------- 128 * Definitions for initial stack pointer and data area (in DPRAM) 129 */ 130#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 131#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 /* Size of used area in internal SRAM */ 132#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 133#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 134 135/*----------------------------------------------------------------------- 136 * Start addresses for the final memory configuration 137 * (Set up by the startup code) 138 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 139 */ 140#define CONFIG_SYS_SDRAM_BASE 0x00000000 141#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */ 142#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE 143#define CONFIG_SYS_INT_FLASH_BASE 0xf0000000 144#define CONFIG_SYS_INT_FLASH_ENABLE 0x21 145 146/* If M5282 port is fully implemented the monitor base will be behind 147 * the vector table. */ 148#if (CONFIG_SYS_TEXT_BASE != CONFIG_SYS_INT_FLASH_BASE) 149#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) 150#else 151#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x418) /* 24 Byte for CFM-Config */ 152#endif 153 154#define CONFIG_SYS_MONITOR_LEN 0x20000 155#define CONFIG_SYS_MALLOC_LEN (256 << 10) 156#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 157 158/* 159 * For booting Linux, the board info and command line data 160 * have to be in the first 8 MB of memory, since this is 161 * the maximum mapped by the Linux kernel during initialization ?? 162 */ 163#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) 164 165/*----------------------------------------------------------------------- 166 * FLASH organization 167 */ 168#define CONFIG_SYS_FLASH_CFI 169#ifdef CONFIG_SYS_FLASH_CFI 170 171# define CONFIG_FLASH_CFI_DRIVER 1 172# define CONFIG_SYS_FLASH_SIZE 0x1000000 /* Max size that the board might have */ 173# define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 174# define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ 175# define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */ 176# define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ 177# define CONFIG_SYS_FLASH_CHECKSUM 178# define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } 179#endif 180 181/*----------------------------------------------------------------------- 182 * Cache Configuration 183 */ 184#define CONFIG_SYS_CACHELINE_SIZE 16 185 186#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 187 CONFIG_SYS_INIT_RAM_SIZE - 8) 188#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 189 CONFIG_SYS_INIT_RAM_SIZE - 4) 190#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV + CF_CACR_DCM) 191#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ 192 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ 193 CF_ACR_EN | CF_ACR_SM_ALL) 194#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_DISD | \ 195 CF_CACR_CEIB | CF_CACR_DBWE | \ 196 CF_CACR_EUSP) 197 198/*----------------------------------------------------------------------- 199 * Memory bank definitions 200 */ 201#define CONFIG_SYS_CS0_BASE 0xFFE00000 202#define CONFIG_SYS_CS0_CTRL 0x00001980 203#define CONFIG_SYS_CS0_MASK 0x001F0001 204 205/*----------------------------------------------------------------------- 206 * Port configuration 207 */ 208#define CONFIG_SYS_PACNT 0x0000000 /* Port A D[31:24] */ 209#define CONFIG_SYS_PADDR 0x0000000 210#define CONFIG_SYS_PADAT 0x0000000 211 212#define CONFIG_SYS_PBCNT 0x0000000 /* Port B D[23:16] */ 213#define CONFIG_SYS_PBDDR 0x0000000 214#define CONFIG_SYS_PBDAT 0x0000000 215 216#define CONFIG_SYS_PCCNT 0x0000000 /* Port C D[15:08] */ 217#define CONFIG_SYS_PCDDR 0x0000000 218#define CONFIG_SYS_PCDAT 0x0000000 219 220#define CONFIG_SYS_PDCNT 0x0000000 /* Port D D[07:00] */ 221#define CONFIG_SYS_PCDDR 0x0000000 222#define CONFIG_SYS_PCDAT 0x0000000 223 224#define CONFIG_SYS_PEHLPAR 0xC0 225#define CONFIG_SYS_PUAPAR 0x0F /* UA0..UA3 = Uart 0 +1 */ 226#define CONFIG_SYS_DDRUA 0x05 227#define CONFIG_SYS_PJPAR 0xFF 228 229#endif /* _CONFIG_M5282EVB_H */ 230