uboot/include/configs/gr_cpci_ax2000.h
<<
>>
Prefs
   1/* Configuration header file for Gaisler GR-CPCI-AX2000
   2 * AX board. Note that since the AX is removable the configuration
   3 * for this board must be edited below.
   4 *
   5 * (C) Copyright 2003-2005
   6 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
   7 *
   8 * (C) Copyright 2008
   9 * Daniel Hellstrom, Gaisler Research, daniel@gaisler.com.
  10 *
  11 * SPDX-License-Identifier:     GPL-2.0+
  12 */
  13
  14#ifndef __CONFIG_H__
  15#define __CONFIG_H__
  16
  17#define CONFIG_SYS_GENERIC_BOARD
  18#define CONFIG_DISPLAY_BOARDINFO
  19
  20/*
  21 * High Level Configuration Options
  22 * (easy to change)
  23 */
  24
  25#define CONFIG_CPCI_AX2000      1       /* ... on GR-CPCI-AX2000 board */
  26
  27#define CONFIG_LEON_RAM_SRAM 1
  28#define CONFIG_LEON_RAM_SDRAM 2
  29#define CONFIG_LEON_RAM_SDRAM_NOSRAM 3
  30
  31/* Select Memory to run from
  32 *
  33 * SRAM          - UBoot is run in SRAM, SRAM-0x40000000, SDRAM-0x60000000
  34 * SDRAM         - UBoot is run in SDRAM, SRAM-0x40000000 and SDRAM-0x60000000
  35 * SDRAM_NOSRAM  - UBoot is run in SDRAM, SRAM not available, SDRAM at 0x40000000
  36 *
  37 * Note, if Linux is to be used, SDRAM or SDRAM_NOSRAM is required since
  38 * it doesn't fit into the 4Mb SRAM.
  39 *
  40 * SRAM is default since it will work for all systems, however will not
  41 * be able to boot linux.
  42 */
  43#define CONFIG_LEON_RAM_SELECT CONFIG_LEON_RAM_SRAM
  44
  45/* CPU / AMBA BUS configuration */
  46#define CONFIG_SYS_CLK_FREQ     20000000        /* 20MHz */
  47
  48/*
  49 * Serial console configuration
  50 */
  51#define CONFIG_BAUDRATE         38400   /* ... at 38400 bps */
  52#define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200, 230400 }
  53
  54/* Partitions */
  55#define CONFIG_DOS_PARTITION
  56#define CONFIG_MAC_PARTITION
  57#define CONFIG_ISO_PARTITION
  58
  59/*
  60 * Supported commands
  61 */
  62#define CONFIG_CMD_REGINFO
  63#define CONFIG_CMD_PING
  64#define CONFIG_CMD_DIAG
  65#define CONFIG_CMD_IRQ
  66
  67/*
  68 * Autobooting
  69 */
  70#define CONFIG_BOOTDELAY        5       /* autoboot after 5 seconds */
  71
  72#define CONFIG_PREBOOT  "echo;" \
  73        "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
  74        "echo"
  75
  76#undef  CONFIG_BOOTARGS
  77
  78#define CONFIG_EXTRA_ENV_SETTINGS_BASE                                  \
  79        "netdev=eth0\0"                                                 \
  80        "nfsargs=setenv bootargs console=ttyS0,38400 root=/dev/nfs rw " \
  81                "nfsroot=${serverip}:${rootpath}\0"                     \
  82        "ramargs=setenv bootargs console=ttyS0,${baudrate} root=/dev/ram rw\0"                  \
  83        "addip=setenv bootargs ${bootargs} "                            \
  84                "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
  85                ":${hostname}:${netdev}:off panic=1\0"                  \
  86        "flash_nfs=run nfsargs addip;"                                  \
  87                "bootm ${kernel_addr}\0"                                \
  88        "flash_self=run ramargs addip;"                                 \
  89                "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
  90        "getkernel=tftpboot $(scratch) $(bootfile)\0" \
  91        "bootargs=console=ttyS0,38400 root=/dev/nfs rw nfsroot=192.168.0.20:/export/rootfs ip=192.168.0.206:192.168.0.20:192.168.0.1:255.255.255.0:ax2000:eth0\0"
  92
  93#if CONFIG_LEON_RAM_SELECT == CONFIG_LEON_RAM_SRAM
  94#define CONFIG_EXTRA_ENV_SETTINGS_SELECT \
  95        "net_nfs=tftp 40000000 ${bootfile};run nfsargs addip;bootm\0"   \
  96        "scratch=40200000\0"                                    \
  97        ""
  98#elif CONFIG_LEON_RAM_SELECT == CONFIG_LEON_RAM_SDRAM
  99#define CONFIG_EXTRA_ENV_SETTINGS_SELECT \
 100        "net_nfs=tftp 60000000 ${bootfile};run nfsargs addip;bootm\0"   \
 101        "scratch=60800000\0"                                    \
 102        ""
 103#else
 104/* More than 4Mb is assumed when running from SDRAM */
 105#define CONFIG_EXTRA_ENV_SETTINGS_SELECT \
 106        "net_nfs=tftp 40000000 ${bootfile};run nfsargs addip;bootm\0"   \
 107        "scratch=40800000\0"                                    \
 108        ""
 109#endif
 110
 111#define CONFIG_EXTRA_ENV_SETTINGS CONFIG_EXTRA_ENV_SETTINGS_BASE CONFIG_EXTRA_ENV_SETTINGS_SELECT
 112
 113#define CONFIG_NETMASK 255.255.255.0
 114#define CONFIG_GATEWAYIP 192.168.0.1
 115#define CONFIG_SERVERIP 192.168.0.20
 116#define CONFIG_IPADDR 192.168.0.206
 117#define CONFIG_ROOTPATH "/export/rootfs"
 118#define CONFIG_HOSTNAME  ax2000
 119#define CONFIG_BOOTFILE "/uImage"
 120
 121#define CONFIG_BOOTCOMMAND      "run flash_self"
 122
 123/* Memory MAP
 124 *
 125 *  Flash:
 126 *  |--------------------------------|
 127 *  | 0x00000000 Text & Data & BSS   | *
 128 *  |            for Monitor         | *
 129 *  | ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~| *
 130 *  | UNUSED / Growth                | * 256kb
 131 *  |--------------------------------|
 132 *  | 0x00050000 Base custom area    | *
 133 *  |            kernel / FS         | *
 134 *  |                                | * Rest of Flash
 135 *  |~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~|
 136 *  | END-0x00008000 Environment     | * 32kb
 137 *  |--------------------------------|
 138 *
 139 *
 140 *
 141 *  Main Memory (4Mb SRAM or XMb SDRAM):
 142 *  |--------------------------------|
 143 *  | UNUSED / scratch area          |
 144 *  |                                |
 145 *  |                                |
 146 *  |                                |
 147 *  |                                |
 148 *  |--------------------------------|
 149 *  | Monitor .Text / .DATA / .BSS   | * 256kb
 150 *  | Relocated!                     | *
 151 *  |--------------------------------|
 152 *  | Monitor Malloc                 | * 128kb (contains relocated environment)
 153 *  |--------------------------------|
 154 *  | Monitor/kernel STACK           | * 64kb
 155 *  |--------------------------------|
 156 *  | Page Table for MMU systems     | * 2k
 157 *  |--------------------------------|
 158 *  | PROM Code accessed from Linux  | * 6kb-128b
 159 *  |--------------------------------|
 160 *  | Global data (avail from kernel)| * 128b
 161 *  |--------------------------------|
 162 *
 163 */
 164
 165/*
 166 * Flash configuration (8,16 or 32 MB)
 167 * TEXT base always at 0xFFF00000
 168 * ENV_ADDR always at  0xFFF40000
 169 * FLASH_BASE at 0xFC000000 for 64 MB
 170 *               0xFE000000 for 32 MB
 171 *               0xFF000000 for 16 MB
 172 *               0xFF800000 for  8 MB
 173 */
 174/*#define CONFIG_SYS_NO_FLASH           1*/
 175#define CONFIG_SYS_FLASH_BASE           0x00000000
 176#define CONFIG_SYS_FLASH_SIZE           0x00800000
 177
 178#define PHYS_FLASH_SECT_SIZE    0x00020000      /* 128 KB sectors */
 179#define CONFIG_SYS_MAX_FLASH_SECT       64      /* max num of sects on one chip */
 180#define CONFIG_SYS_MAX_FLASH_BANKS      1       /* max num of memory banks      */
 181
 182#define CONFIG_SYS_FLASH_ERASE_TOUT     240000  /* Flash Erase Timeout (in ms)  */
 183#define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (in ms)  */
 184#define CONFIG_SYS_FLASH_LOCK_TOUT      5       /* Timeout for Flash Set Lock Bit (in ms) */
 185#define CONFIG_SYS_FLASH_UNLOCK_TOUT    10000   /* Timeout for Flash Clear Lock Bits (in ms) */
 186#define CONFIG_SYS_FLASH_PROTECTION     /* "Real" (hardware) sectors protection */
 187
 188/*** CFI CONFIG ***/
 189#define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_8BIT
 190#define CONFIG_FLASH_CFI_DRIVER
 191#define CONFIG_SYS_FLASH_CFI
 192/* Bypass cache when reading regs from flash memory */
 193#define CONFIG_SYS_FLASH_CFI_BYPASS_READ
 194/* Buffered writes (32byte/go) instead of single accesses */
 195#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 196
 197/*
 198 * Environment settings
 199 */
 200/*#define CONFIG_ENV_IS_NOWHERE 1*/
 201#define CONFIG_ENV_IS_IN_FLASH  1
 202/* CONFIG_ENV_ADDR need to be at sector boundary */
 203#define CONFIG_ENV_SIZE         0x8000
 204#define CONFIG_ENV_SECT_SIZE    0x20000
 205#define CONFIG_ENV_ADDR         (CONFIG_SYS_FLASH_BASE+CONFIG_SYS_FLASH_SIZE-CONFIG_ENV_SECT_SIZE)
 206#define CONFIG_ENV_OVERWRITE    1
 207
 208/*
 209 * Memory map
 210 *
 211 * Always 4Mb SRAM available
 212 * SDRAM module may be available on 0x60000000, SDRAM
 213 * is configured as if a 128Mb SDRAM module is available.
 214 */
 215
 216#if CONFIG_LEON_RAM_SELECT == CONFIG_LEON_RAM_SDRAM_NOSRAM
 217#define CONFIG_SYS_SDRAM_BASE           0x40000000
 218#else
 219#define CONFIG_SYS_SDRAM_BASE           0x60000000
 220#endif
 221
 222#define CONFIG_SYS_SDRAM_SIZE           0x08000000
 223#define CONFIG_SYS_SDRAM_END            (CONFIG_SYS_SDRAM_BASE+CONFIG_SYS_SDRAM_SIZE)
 224
 225/* 4Mb SRAM available */
 226#if CONFIG_LEON_RAM_SELECT != CONFIG_LEON_RAM_SDRAM_NOSRAM
 227#define CONFIG_SYS_SRAM_BASE 0x40000000
 228#define CONFIG_SYS_SRAM_SIZE 0x400000
 229#define CONFIG_SYS_SRAM_END  (CONFIG_SYS_SRAM_BASE+CONFIG_SYS_SRAM_SIZE)
 230#endif
 231
 232/* Select RAM used to run U-BOOT from... */
 233#if CONFIG_LEON_RAM_SELECT == CONFIG_LEON_RAM_SRAM
 234#define CONFIG_SYS_RAM_BASE CONFIG_SYS_SRAM_BASE
 235#define CONFIG_SYS_RAM_SIZE CONFIG_SYS_SRAM_SIZE
 236#define CONFIG_SYS_RAM_END CONFIG_SYS_SRAM_END
 237#else
 238#define CONFIG_SYS_RAM_BASE CONFIG_SYS_SDRAM_BASE
 239#define CONFIG_SYS_RAM_SIZE CONFIG_SYS_SDRAM_SIZE
 240#define CONFIG_SYS_RAM_END CONFIG_SYS_SDRAM_END
 241#endif
 242
 243#define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_RAM_END - GENERATED_GBL_DATA_SIZE)
 244
 245#define CONFIG_SYS_PROM_SIZE            (8192-GENERATED_GBL_DATA_SIZE)
 246#define CONFIG_SYS_PROM_OFFSET          (CONFIG_SYS_GBL_DATA_OFFSET-CONFIG_SYS_PROM_SIZE)
 247
 248#define CONFIG_SYS_INIT_SP_OFFSET       (CONFIG_SYS_PROM_OFFSET-32)
 249#define CONFIG_SYS_STACK_SIZE           (0x10000-32)
 250
 251#define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
 252#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 253#   define CONFIG_SYS_RAMBOOT           1
 254#endif
 255
 256#define CONFIG_SYS_MONITOR_LEN          (256 << 10)     /* Reserve 256 kB for Monitor   */
 257#define CONFIG_SYS_MALLOC_LEN           (128 << 10)     /* Reserve 128 kB for malloc()  */
 258#define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* Initial Memory map for Linux */
 259
 260#define CONFIG_SYS_MALLOC_END           (CONFIG_SYS_INIT_SP_OFFSET-CONFIG_SYS_STACK_SIZE)
 261#define CONFIG_SYS_MALLOC_BASE          (CONFIG_SYS_MALLOC_END-CONFIG_SYS_MALLOC_LEN)
 262
 263/* relocated monitor area */
 264#define CONFIG_SYS_RELOC_MONITOR_MAX_END   CONFIG_SYS_MALLOC_BASE
 265#define CONFIG_SYS_RELOC_MONITOR_BASE     (CONFIG_SYS_RELOC_MONITOR_MAX_END-CONFIG_SYS_MONITOR_LEN)
 266
 267/* make un relocated address from relocated address */
 268#define UN_RELOC(address) (address-(CONFIG_SYS_RELOC_MONITOR_BASE-CONFIG_SYS_TEXT_BASE))
 269
 270/*
 271 * Ethernet configuration uses on board SMC91C111
 272 */
 273#define CONFIG_SMC91111          1
 274#define CONFIG_SMC91111_BASE            0x20000300      /* chip select 3         */
 275#define CONFIG_SMC_USE_32_BIT           1       /* 32 bit bus  */
 276#undef  CONFIG_SMC_91111_EXT_PHY        /* we use internal phy   */
 277/*#define CONFIG_SHOW_ACTIVITY*/
 278#define CONFIG_NET_RETRY_COUNT          10      /* # of retries          */
 279
 280#define CONFIG_PHY_ADDR  0x00
 281
 282/*
 283 * Miscellaneous configurable options
 284 */
 285#define CONFIG_SYS_LONGHELP             /* undef to save memory     */
 286#if defined(CONFIG_CMD_KGDB)
 287#define CONFIG_SYS_CBSIZE               1024    /* Console I/O Buffer Size  */
 288#else
 289#define CONFIG_SYS_CBSIZE               256     /* Console I/O Buffer Size  */
 290#endif
 291#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)      /* Print Buffer Size */
 292#define CONFIG_SYS_MAXARGS              16      /* max number of command args   */
 293#define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 294
 295#define CONFIG_SYS_MEMTEST_START        0x00100000      /* memtest works on */
 296#define CONFIG_SYS_MEMTEST_END          0x00f00000      /* 1 ... 15 MB in DRAM  */
 297
 298#define CONFIG_SYS_LOAD_ADDR            0x100000        /* default load address */
 299
 300/*
 301 * Various low-level settings
 302 */
 303
 304/*-----------------------------------------------------------------------
 305 * USB stuff
 306 *-----------------------------------------------------------------------
 307 */
 308#define CONFIG_USB_CLOCK        0x0001BBBB
 309#define CONFIG_USB_CONFIG       0x00005000
 310
 311/***** Gaisler GRLIB IP-Cores Config ********/
 312
 313#define CONFIG_SYS_GRLIB_SDRAM    0
 314
 315/* No SDRAM Configuration */
 316#undef CONFIG_SYS_GRLIB_GAISLER_SDCTRL1
 317
 318/* See, GRLIB Docs (grip.pdf) on how to set up
 319 * These the memory controller registers.
 320 */
 321#define CONFIG_SYS_GRLIB_ESA_MCTRL1
 322#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG1   (0x10f800ff | (1<<11))
 323#if CONFIG_LEON_RAM_SELECT == CONFIG_LEON_RAM_SDRAM_NOSRAM
 324#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG2   0x82206000
 325#else
 326#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG2   0x82205260
 327#endif
 328#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG3   0x0809a000
 329
 330/* GRLIB FT-MCTRL configuration */
 331#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1
 332#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG1   (0x10f800ff | (1<<11))
 333#if CONFIG_LEON_RAM_SELECT == CONFIG_LEON_RAM_SDRAM_NOSRAM
 334#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG2   0x82206000
 335#else
 336#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG2   0x82205260
 337#endif
 338#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG3   0x0809a000
 339
 340/* no DDR controller */
 341#undef CONFIG_SYS_GRLIB_GAISLER_DDRSPA1
 342
 343/* no DDR2 Controller */
 344#undef CONFIG_SYS_GRLIB_GAISLER_DDR2SPA1
 345
 346/* Identification string */
 347#define CONFIG_IDENT_STRING " Gaisler LEON3 GR-CPCI-AX2000"
 348
 349/* default kernel command line */
 350#define CONFIG_DEFAULT_KERNEL_COMMAND_LINE "console=ttyS0,38400\0\0"
 351
 352#endif                          /* __CONFIG_H */
 353