uboot/arch/arm/cpu/armv7/mx6/clock.c
<<
>>
Prefs
   1/*
   2 * Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
   3 *
   4 * SPDX-License-Identifier:     GPL-2.0+
   5 */
   6
   7#include <common.h>
   8#include <div64.h>
   9#include <asm/io.h>
  10#include <asm/errno.h>
  11#include <asm/arch/imx-regs.h>
  12#include <asm/arch/crm_regs.h>
  13#include <asm/arch/clock.h>
  14#include <asm/arch/sys_proto.h>
  15
  16enum pll_clocks {
  17        PLL_SYS,        /* System PLL */
  18        PLL_BUS,        /* System Bus PLL*/
  19        PLL_USBOTG,     /* OTG USB PLL */
  20        PLL_ENET,       /* ENET PLL */
  21        PLL_AUDIO,      /* AUDIO PLL */
  22        PLL_VIDEO,      /* AUDIO PLL */
  23};
  24
  25struct mxc_ccm_reg *imx_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
  26
  27#ifdef CONFIG_MXC_OCOTP
  28void enable_ocotp_clk(unsigned char enable)
  29{
  30        u32 reg;
  31
  32        reg = __raw_readl(&imx_ccm->CCGR2);
  33        if (enable)
  34                reg |= MXC_CCM_CCGR2_OCOTP_CTRL_MASK;
  35        else
  36                reg &= ~MXC_CCM_CCGR2_OCOTP_CTRL_MASK;
  37        __raw_writel(reg, &imx_ccm->CCGR2);
  38}
  39#endif
  40
  41#ifdef CONFIG_NAND_MXS
  42void setup_gpmi_io_clk(u32 cfg)
  43{
  44        /* Disable clocks per ERR007177 from MX6 errata */
  45        clrbits_le32(&imx_ccm->CCGR4,
  46                     MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
  47                     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
  48                     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
  49                     MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
  50                     MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_MASK);
  51
  52#if defined(CONFIG_MX6SX)
  53        clrbits_le32(&imx_ccm->CCGR4, MXC_CCM_CCGR4_QSPI2_ENFC_MASK);
  54
  55        clrsetbits_le32(&imx_ccm->cs2cdr,
  56                        MXC_CCM_CS2CDR_QSPI2_CLK_PODF_MASK |
  57                        MXC_CCM_CS2CDR_QSPI2_CLK_PRED_MASK |
  58                        MXC_CCM_CS2CDR_QSPI2_CLK_SEL_MASK,
  59                        cfg);
  60
  61        setbits_le32(&imx_ccm->CCGR4, MXC_CCM_CCGR4_QSPI2_ENFC_MASK);
  62#else
  63        clrbits_le32(&imx_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
  64
  65        clrsetbits_le32(&imx_ccm->cs2cdr,
  66                        MXC_CCM_CS2CDR_ENFC_CLK_PODF_MASK |
  67                        MXC_CCM_CS2CDR_ENFC_CLK_PRED_MASK |
  68                        MXC_CCM_CS2CDR_ENFC_CLK_SEL_MASK,
  69                        cfg);
  70
  71        setbits_le32(&imx_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
  72#endif
  73        setbits_le32(&imx_ccm->CCGR4,
  74                     MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
  75                     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
  76                     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
  77                     MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
  78                     MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_MASK);
  79}
  80#endif
  81
  82void enable_usboh3_clk(unsigned char enable)
  83{
  84        u32 reg;
  85
  86        reg = __raw_readl(&imx_ccm->CCGR6);
  87        if (enable)
  88                reg |= MXC_CCM_CCGR6_USBOH3_MASK;
  89        else
  90                reg &= ~(MXC_CCM_CCGR6_USBOH3_MASK);
  91        __raw_writel(reg, &imx_ccm->CCGR6);
  92
  93}
  94
  95#if defined(CONFIG_FEC_MXC) && !defined(CONFIG_MX6SX)
  96void enable_enet_clk(unsigned char enable)
  97{
  98        u32 mask, *addr;
  99
 100        if (is_cpu_type(MXC_CPU_MX6UL)) {
 101                mask = MXC_CCM_CCGR3_ENET_MASK;
 102                addr = &imx_ccm->CCGR3;
 103        } else {
 104                mask = MXC_CCM_CCGR1_ENET_MASK;
 105                addr = &imx_ccm->CCGR1;
 106        }
 107
 108        if (enable)
 109                setbits_le32(addr, mask);
 110        else
 111                clrbits_le32(addr, mask);
 112}
 113#endif
 114
 115#ifdef CONFIG_MXC_UART
 116void enable_uart_clk(unsigned char enable)
 117{
 118        u32 mask;
 119
 120        if (is_cpu_type(MXC_CPU_MX6UL))
 121                mask = MXC_CCM_CCGR5_UART_MASK;
 122        else
 123                mask = MXC_CCM_CCGR5_UART_MASK | MXC_CCM_CCGR5_UART_SERIAL_MASK;
 124
 125        if (enable)
 126                setbits_le32(&imx_ccm->CCGR5, mask);
 127        else
 128                clrbits_le32(&imx_ccm->CCGR5, mask);
 129}
 130#endif
 131
 132#ifdef CONFIG_MMC
 133int enable_usdhc_clk(unsigned char enable, unsigned bus_num)
 134{
 135        u32 mask;
 136
 137        if (bus_num > 3)
 138                return -EINVAL;
 139
 140        mask = MXC_CCM_CCGR_CG_MASK << (bus_num * 2 + 2);
 141        if (enable)
 142                setbits_le32(&imx_ccm->CCGR6, mask);
 143        else
 144                clrbits_le32(&imx_ccm->CCGR6, mask);
 145
 146        return 0;
 147}
 148#endif
 149
 150#ifdef CONFIG_SYS_I2C_MXC
 151/* i2c_num can be from 0 - 3 */
 152int enable_i2c_clk(unsigned char enable, unsigned i2c_num)
 153{
 154        u32 reg;
 155        u32 mask;
 156        u32 *addr;
 157
 158        if (i2c_num > 3)
 159                return -EINVAL;
 160        if (i2c_num < 3) {
 161                mask = MXC_CCM_CCGR_CG_MASK
 162                        << (MXC_CCM_CCGR2_I2C1_SERIAL_OFFSET
 163                        + (i2c_num << 1));
 164                reg = __raw_readl(&imx_ccm->CCGR2);
 165                if (enable)
 166                        reg |= mask;
 167                else
 168                        reg &= ~mask;
 169                __raw_writel(reg, &imx_ccm->CCGR2);
 170        } else {
 171                if (is_cpu_type(MXC_CPU_MX6SX) || is_cpu_type(MXC_CPU_MX6UL)) {
 172                        mask = MXC_CCM_CCGR6_I2C4_MASK;
 173                        addr = &imx_ccm->CCGR6;
 174                } else {
 175                        mask = MXC_CCM_CCGR1_I2C4_SERIAL_MASK;
 176                        addr = &imx_ccm->CCGR1;
 177                }
 178                reg = __raw_readl(addr);
 179                if (enable)
 180                        reg |= mask;
 181                else
 182                        reg &= ~mask;
 183                __raw_writel(reg, addr);
 184        }
 185        return 0;
 186}
 187#endif
 188
 189/* spi_num can be from 0 - SPI_MAX_NUM */
 190int enable_spi_clk(unsigned char enable, unsigned spi_num)
 191{
 192        u32 reg;
 193        u32 mask;
 194
 195        if (spi_num > SPI_MAX_NUM)
 196                return -EINVAL;
 197
 198        mask = MXC_CCM_CCGR_CG_MASK << (spi_num << 1);
 199        reg = __raw_readl(&imx_ccm->CCGR1);
 200        if (enable)
 201                reg |= mask;
 202        else
 203                reg &= ~mask;
 204        __raw_writel(reg, &imx_ccm->CCGR1);
 205        return 0;
 206}
 207static u32 decode_pll(enum pll_clocks pll, u32 infreq)
 208{
 209        u32 div, test_div, pll_num, pll_denom;
 210
 211        switch (pll) {
 212        case PLL_SYS:
 213                div = __raw_readl(&imx_ccm->analog_pll_sys);
 214                div &= BM_ANADIG_PLL_SYS_DIV_SELECT;
 215
 216                return (infreq * div) >> 1;
 217        case PLL_BUS:
 218                div = __raw_readl(&imx_ccm->analog_pll_528);
 219                div &= BM_ANADIG_PLL_528_DIV_SELECT;
 220
 221                return infreq * (20 + (div << 1));
 222        case PLL_USBOTG:
 223                div = __raw_readl(&imx_ccm->analog_usb1_pll_480_ctrl);
 224                div &= BM_ANADIG_USB1_PLL_480_CTRL_DIV_SELECT;
 225
 226                return infreq * (20 + (div << 1));
 227        case PLL_ENET:
 228                div = __raw_readl(&imx_ccm->analog_pll_enet);
 229                div &= BM_ANADIG_PLL_ENET_DIV_SELECT;
 230
 231                return 25000000 * (div + (div >> 1) + 1);
 232        case PLL_AUDIO:
 233                div = __raw_readl(&imx_ccm->analog_pll_audio);
 234                if (!(div & BM_ANADIG_PLL_AUDIO_ENABLE))
 235                        return 0;
 236                /* BM_ANADIG_PLL_AUDIO_BYPASS_CLK_SRC is ignored */
 237                if (div & BM_ANADIG_PLL_AUDIO_BYPASS)
 238                        return MXC_HCLK;
 239                pll_num = __raw_readl(&imx_ccm->analog_pll_audio_num);
 240                pll_denom = __raw_readl(&imx_ccm->analog_pll_audio_denom);
 241                test_div = (div & BM_ANADIG_PLL_AUDIO_TEST_DIV_SELECT) >>
 242                        BP_ANADIG_PLL_AUDIO_TEST_DIV_SELECT;
 243                div &= BM_ANADIG_PLL_AUDIO_DIV_SELECT;
 244                if (test_div == 3) {
 245                        debug("Error test_div\n");
 246                        return 0;
 247                }
 248                test_div = 1 << (2 - test_div);
 249
 250                return infreq * (div + pll_num / pll_denom) / test_div;
 251        case PLL_VIDEO:
 252                div = __raw_readl(&imx_ccm->analog_pll_video);
 253                if (!(div & BM_ANADIG_PLL_VIDEO_ENABLE))
 254                        return 0;
 255                /* BM_ANADIG_PLL_AUDIO_BYPASS_CLK_SRC is ignored */
 256                if (div & BM_ANADIG_PLL_VIDEO_BYPASS)
 257                        return MXC_HCLK;
 258                pll_num = __raw_readl(&imx_ccm->analog_pll_video_num);
 259                pll_denom = __raw_readl(&imx_ccm->analog_pll_video_denom);
 260                test_div = (div & BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT) >>
 261                        BP_ANADIG_PLL_VIDEO_POST_DIV_SELECT;
 262                div &= BM_ANADIG_PLL_VIDEO_DIV_SELECT;
 263                if (test_div == 3) {
 264                        debug("Error test_div\n");
 265                        return 0;
 266                }
 267                test_div = 1 << (2 - test_div);
 268
 269                return infreq * (div + pll_num / pll_denom) / test_div;
 270        default:
 271                return 0;
 272        }
 273        /* NOTREACHED */
 274}
 275static u32 mxc_get_pll_pfd(enum pll_clocks pll, int pfd_num)
 276{
 277        u32 div;
 278        u64 freq;
 279
 280        switch (pll) {
 281        case PLL_BUS:
 282                if (!is_cpu_type(MXC_CPU_MX6UL)) {
 283                        if (pfd_num == 3) {
 284                                /* No PFD3 on PPL2 */
 285                                return 0;
 286                        }
 287                }
 288                div = __raw_readl(&imx_ccm->analog_pfd_528);
 289                freq = (u64)decode_pll(PLL_BUS, MXC_HCLK);
 290                break;
 291        case PLL_USBOTG:
 292                div = __raw_readl(&imx_ccm->analog_pfd_480);
 293                freq = (u64)decode_pll(PLL_USBOTG, MXC_HCLK);
 294                break;
 295        default:
 296                /* No PFD on other PLL                                       */
 297                return 0;
 298        }
 299
 300        return lldiv(freq * 18, (div & ANATOP_PFD_FRAC_MASK(pfd_num)) >>
 301                              ANATOP_PFD_FRAC_SHIFT(pfd_num));
 302}
 303
 304static u32 get_mcu_main_clk(void)
 305{
 306        u32 reg, freq;
 307
 308        reg = __raw_readl(&imx_ccm->cacrr);
 309        reg &= MXC_CCM_CACRR_ARM_PODF_MASK;
 310        reg >>= MXC_CCM_CACRR_ARM_PODF_OFFSET;
 311        freq = decode_pll(PLL_SYS, MXC_HCLK);
 312
 313        return freq / (reg + 1);
 314}
 315
 316u32 get_periph_clk(void)
 317{
 318        u32 reg, div = 0, freq = 0;
 319
 320        reg = __raw_readl(&imx_ccm->cbcdr);
 321        if (reg & MXC_CCM_CBCDR_PERIPH_CLK_SEL) {
 322                div = (reg & MXC_CCM_CBCDR_PERIPH_CLK2_PODF_MASK) >>
 323                       MXC_CCM_CBCDR_PERIPH_CLK2_PODF_OFFSET;
 324                reg = __raw_readl(&imx_ccm->cbcmr);
 325                reg &= MXC_CCM_CBCMR_PERIPH_CLK2_SEL_MASK;
 326                reg >>= MXC_CCM_CBCMR_PERIPH_CLK2_SEL_OFFSET;
 327
 328                switch (reg) {
 329                case 0:
 330                        freq = decode_pll(PLL_USBOTG, MXC_HCLK);
 331                        break;
 332                case 1:
 333                case 2:
 334                        freq = MXC_HCLK;
 335                        break;
 336                default:
 337                        break;
 338                }
 339        } else {
 340                reg = __raw_readl(&imx_ccm->cbcmr);
 341                reg &= MXC_CCM_CBCMR_PRE_PERIPH_CLK_SEL_MASK;
 342                reg >>= MXC_CCM_CBCMR_PRE_PERIPH_CLK_SEL_OFFSET;
 343
 344                switch (reg) {
 345                case 0:
 346                        freq = decode_pll(PLL_BUS, MXC_HCLK);
 347                        break;
 348                case 1:
 349                        freq = mxc_get_pll_pfd(PLL_BUS, 2);
 350                        break;
 351                case 2:
 352                        freq = mxc_get_pll_pfd(PLL_BUS, 0);
 353                        break;
 354                case 3:
 355                        /* static / 2 divider */
 356                        freq = mxc_get_pll_pfd(PLL_BUS, 2) / 2;
 357                        break;
 358                default:
 359                        break;
 360                }
 361        }
 362
 363        return freq / (div + 1);
 364}
 365
 366static u32 get_ipg_clk(void)
 367{
 368        u32 reg, ipg_podf;
 369
 370        reg = __raw_readl(&imx_ccm->cbcdr);
 371        reg &= MXC_CCM_CBCDR_IPG_PODF_MASK;
 372        ipg_podf = reg >> MXC_CCM_CBCDR_IPG_PODF_OFFSET;
 373
 374        return get_ahb_clk() / (ipg_podf + 1);
 375}
 376
 377static u32 get_ipg_per_clk(void)
 378{
 379        u32 reg, perclk_podf;
 380
 381        reg = __raw_readl(&imx_ccm->cscmr1);
 382        if (is_cpu_type(MXC_CPU_MX6SL) || is_cpu_type(MXC_CPU_MX6SX) ||
 383            is_mx6dqp() || is_cpu_type(MXC_CPU_MX6UL)) {
 384                if (reg & MXC_CCM_CSCMR1_PER_CLK_SEL_MASK)
 385                        return MXC_HCLK; /* OSC 24Mhz */
 386        }
 387
 388        perclk_podf = reg & MXC_CCM_CSCMR1_PERCLK_PODF_MASK;
 389
 390        return get_ipg_clk() / (perclk_podf + 1);
 391}
 392
 393static u32 get_uart_clk(void)
 394{
 395        u32 reg, uart_podf;
 396        u32 freq = decode_pll(PLL_USBOTG, MXC_HCLK) / 6; /* static divider */
 397        reg = __raw_readl(&imx_ccm->cscdr1);
 398
 399        if (is_cpu_type(MXC_CPU_MX6SL) || is_cpu_type(MXC_CPU_MX6SX) ||
 400            is_mx6dqp() || is_cpu_type(MXC_CPU_MX6UL)) {
 401                if (reg & MXC_CCM_CSCDR1_UART_CLK_SEL)
 402                        freq = MXC_HCLK;
 403        }
 404
 405        reg &= MXC_CCM_CSCDR1_UART_CLK_PODF_MASK;
 406        uart_podf = reg >> MXC_CCM_CSCDR1_UART_CLK_PODF_OFFSET;
 407
 408        return freq / (uart_podf + 1);
 409}
 410
 411static u32 get_cspi_clk(void)
 412{
 413        u32 reg, cspi_podf;
 414
 415        reg = __raw_readl(&imx_ccm->cscdr2);
 416        cspi_podf = (reg & MXC_CCM_CSCDR2_ECSPI_CLK_PODF_MASK) >>
 417                     MXC_CCM_CSCDR2_ECSPI_CLK_PODF_OFFSET;
 418
 419        if (is_mx6dqp() || is_cpu_type(MXC_CPU_MX6SL) ||
 420            is_cpu_type(MXC_CPU_MX6SX) || is_cpu_type(MXC_CPU_MX6UL)) {
 421                if (reg & MXC_CCM_CSCDR2_ECSPI_CLK_SEL_MASK)
 422                        return MXC_HCLK / (cspi_podf + 1);
 423        }
 424
 425        return  decode_pll(PLL_USBOTG, MXC_HCLK) / (8 * (cspi_podf + 1));
 426}
 427
 428static u32 get_axi_clk(void)
 429{
 430        u32 root_freq, axi_podf;
 431        u32 cbcdr =  __raw_readl(&imx_ccm->cbcdr);
 432
 433        axi_podf = cbcdr & MXC_CCM_CBCDR_AXI_PODF_MASK;
 434        axi_podf >>= MXC_CCM_CBCDR_AXI_PODF_OFFSET;
 435
 436        if (cbcdr & MXC_CCM_CBCDR_AXI_SEL) {
 437                if (cbcdr & MXC_CCM_CBCDR_AXI_ALT_SEL)
 438                        root_freq = mxc_get_pll_pfd(PLL_BUS, 2);
 439                else
 440                        root_freq = mxc_get_pll_pfd(PLL_USBOTG, 1);
 441        } else
 442                root_freq = get_periph_clk();
 443
 444        return  root_freq / (axi_podf + 1);
 445}
 446
 447static u32 get_emi_slow_clk(void)
 448{
 449        u32 emi_clk_sel, emi_slow_podf, cscmr1, root_freq = 0;
 450
 451        cscmr1 =  __raw_readl(&imx_ccm->cscmr1);
 452        emi_clk_sel = cscmr1 & MXC_CCM_CSCMR1_ACLK_EMI_SLOW_MASK;
 453        emi_clk_sel >>= MXC_CCM_CSCMR1_ACLK_EMI_SLOW_OFFSET;
 454        emi_slow_podf = cscmr1 & MXC_CCM_CSCMR1_ACLK_EMI_SLOW_PODF_MASK;
 455        emi_slow_podf >>= MXC_CCM_CSCMR1_ACLK_EMI_SLOW_PODF_OFFSET;
 456
 457        switch (emi_clk_sel) {
 458        case 0:
 459                root_freq = get_axi_clk();
 460                break;
 461        case 1:
 462                root_freq = decode_pll(PLL_USBOTG, MXC_HCLK);
 463                break;
 464        case 2:
 465                root_freq =  mxc_get_pll_pfd(PLL_BUS, 2);
 466                break;
 467        case 3:
 468                root_freq =  mxc_get_pll_pfd(PLL_BUS, 0);
 469                break;
 470        }
 471
 472        return root_freq / (emi_slow_podf + 1);
 473}
 474
 475static u32 get_mmdc_ch0_clk(void)
 476{
 477        u32 cbcmr = __raw_readl(&imx_ccm->cbcmr);
 478        u32 cbcdr = __raw_readl(&imx_ccm->cbcdr);
 479
 480        u32 freq, podf, per2_clk2_podf, pmu_misc2_audio_div;
 481
 482        if (is_cpu_type(MXC_CPU_MX6SX) || is_cpu_type(MXC_CPU_MX6UL) ||
 483            is_cpu_type(MXC_CPU_MX6SL)) {
 484                podf = (cbcdr & MXC_CCM_CBCDR_MMDC_CH1_PODF_MASK) >>
 485                        MXC_CCM_CBCDR_MMDC_CH1_PODF_OFFSET;
 486                if (cbcdr & MXC_CCM_CBCDR_PERIPH2_CLK_SEL) {
 487                        per2_clk2_podf = (cbcdr & MXC_CCM_CBCDR_PERIPH2_CLK2_PODF_MASK) >>
 488                                MXC_CCM_CBCDR_PERIPH2_CLK2_PODF_OFFSET;
 489                        if (is_cpu_type(MXC_CPU_MX6SL)) {
 490                                if (cbcmr & MXC_CCM_CBCMR_PERIPH2_CLK2_SEL)
 491                                        freq = MXC_HCLK;
 492                                else
 493                                        freq = decode_pll(PLL_USBOTG, MXC_HCLK);
 494                        } else {
 495                                if (cbcmr & MXC_CCM_CBCMR_PERIPH2_CLK2_SEL)
 496                                        freq = decode_pll(PLL_BUS, MXC_HCLK);
 497                                else
 498                                        freq = decode_pll(PLL_USBOTG, MXC_HCLK);
 499                        }
 500                } else {
 501                        per2_clk2_podf = 0;
 502                        switch ((cbcmr &
 503                                MXC_CCM_CBCMR_PRE_PERIPH2_CLK_SEL_MASK) >>
 504                                MXC_CCM_CBCMR_PRE_PERIPH2_CLK_SEL_OFFSET) {
 505                        case 0:
 506                                freq = decode_pll(PLL_BUS, MXC_HCLK);
 507                                break;
 508                        case 1:
 509                                freq = mxc_get_pll_pfd(PLL_BUS, 2);
 510                                break;
 511                        case 2:
 512                                freq = mxc_get_pll_pfd(PLL_BUS, 0);
 513                                break;
 514                        case 3:
 515                                pmu_misc2_audio_div = PMU_MISC2_AUDIO_DIV(__raw_readl(&imx_ccm->pmu_misc2));
 516                                switch (pmu_misc2_audio_div) {
 517                                case 0:
 518                                case 2:
 519                                        pmu_misc2_audio_div = 1;
 520                                        break;
 521                                case 1:
 522                                        pmu_misc2_audio_div = 2;
 523                                        break;
 524                                case 3:
 525                                        pmu_misc2_audio_div = 4;
 526                                        break;
 527                                }
 528                                freq = decode_pll(PLL_AUDIO, MXC_HCLK) /
 529                                        pmu_misc2_audio_div;
 530                                break;
 531                        }
 532                }
 533                return freq / (podf + 1) / (per2_clk2_podf + 1);
 534        } else {
 535                podf = (cbcdr & MXC_CCM_CBCDR_MMDC_CH0_PODF_MASK) >>
 536                        MXC_CCM_CBCDR_MMDC_CH0_PODF_OFFSET;
 537                return get_periph_clk() / (podf + 1);
 538        }
 539}
 540
 541#if defined(CONFIG_VIDEO_MXS)
 542static int enable_pll_video(u32 pll_div, u32 pll_num, u32 pll_denom,
 543                            u32 post_div)
 544{
 545        u32 reg = 0;
 546        ulong start;
 547
 548        debug("pll5 div = %d, num = %d, denom = %d\n",
 549              pll_div, pll_num, pll_denom);
 550
 551        /* Power up PLL5 video */
 552        writel(BM_ANADIG_PLL_VIDEO_POWERDOWN |
 553               BM_ANADIG_PLL_VIDEO_BYPASS |
 554               BM_ANADIG_PLL_VIDEO_DIV_SELECT |
 555               BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT,
 556               &imx_ccm->analog_pll_video_clr);
 557
 558        /* Set div, num and denom */
 559        switch (post_div) {
 560        case 1:
 561                writel(BF_ANADIG_PLL_VIDEO_DIV_SELECT(pll_div) |
 562                       BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(0x2),
 563                       &imx_ccm->analog_pll_video_set);
 564                break;
 565        case 2:
 566                writel(BF_ANADIG_PLL_VIDEO_DIV_SELECT(pll_div) |
 567                       BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(0x1),
 568                       &imx_ccm->analog_pll_video_set);
 569                break;
 570        case 4:
 571                writel(BF_ANADIG_PLL_VIDEO_DIV_SELECT(pll_div) |
 572                       BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(0x0),
 573                       &imx_ccm->analog_pll_video_set);
 574                break;
 575        default:
 576                puts("Wrong test_div!\n");
 577                return -EINVAL;
 578        }
 579
 580        writel(BF_ANADIG_PLL_VIDEO_NUM_A(pll_num),
 581               &imx_ccm->analog_pll_video_num);
 582        writel(BF_ANADIG_PLL_VIDEO_DENOM_B(pll_denom),
 583               &imx_ccm->analog_pll_video_denom);
 584
 585        /* Wait PLL5 lock */
 586        start = get_timer(0);   /* Get current timestamp */
 587
 588        do {
 589                reg = readl(&imx_ccm->analog_pll_video);
 590                if (reg & BM_ANADIG_PLL_VIDEO_LOCK) {
 591                        /* Enable PLL out */
 592                        writel(BM_ANADIG_PLL_VIDEO_ENABLE,
 593                               &imx_ccm->analog_pll_video_set);
 594                        return 0;
 595                }
 596        } while (get_timer(0) < (start + 10)); /* Wait 10ms */
 597
 598        puts("Lock PLL5 timeout\n");
 599
 600        return -ETIME;
 601}
 602
 603/*
 604 * 24M--> PLL_VIDEO -> LCDIFx_PRED -> LCDIFx_PODF -> LCD
 605 *
 606 * 'freq' using KHz as unit, see driver/video/mxsfb.c.
 607 */
 608void mxs_set_lcdclk(u32 base_addr, u32 freq)
 609{
 610        u32 reg = 0;
 611        u32 hck = MXC_HCLK / 1000;
 612        /* DIV_SELECT ranges from 27 to 54 */
 613        u32 min = hck * 27;
 614        u32 max = hck * 54;
 615        u32 temp, best = 0;
 616        u32 i, j, max_pred = 8, max_postd = 8, pred = 1, postd = 1;
 617        u32 pll_div, pll_num, pll_denom, post_div = 1;
 618
 619        debug("mxs_set_lcdclk, freq = %dKHz\n", freq);
 620
 621        if ((!is_cpu_type(MXC_CPU_MX6SX)) && !is_cpu_type(MXC_CPU_MX6UL)) {
 622                debug("This chip not support lcd!\n");
 623                return;
 624        }
 625
 626        if (base_addr == LCDIF1_BASE_ADDR) {
 627                reg = readl(&imx_ccm->cscdr2);
 628                /* Can't change clocks when clock not from pre-mux */
 629                if ((reg & MXC_CCM_CSCDR2_LCDIF1_CLK_SEL_MASK) != 0)
 630                        return;
 631        }
 632
 633        if (is_cpu_type(MXC_CPU_MX6SX)) {
 634                reg = readl(&imx_ccm->cscdr2);
 635                /* Can't change clocks when clock not from pre-mux */
 636                if ((reg & MXC_CCM_CSCDR2_LCDIF2_CLK_SEL_MASK) != 0)
 637                        return;
 638        }
 639
 640        temp = freq * max_pred * max_postd;
 641        if (temp < min) {
 642                /*
 643                 * Register: PLL_VIDEO
 644                 * Bit Field: POST_DIV_SELECT
 645                 * 00 — Divide by 4.
 646                 * 01 — Divide by 2.
 647                 * 10 — Divide by 1.
 648                 * 11 — Reserved
 649                 * No need to check post_div(1)
 650                 */
 651                for (post_div = 2; post_div <= 4; post_div <<= 1) {
 652                        if ((temp * post_div) > min) {
 653                                freq *= post_div;
 654                                break;
 655                        }
 656                }
 657
 658                if (post_div > 4) {
 659                        printf("Fail to set rate to %dkhz", freq);
 660                        return;
 661                }
 662        }
 663
 664        /* Choose the best pred and postd to match freq for lcd */
 665        for (i = 1; i <= max_pred; i++) {
 666                for (j = 1; j <= max_postd; j++) {
 667                        temp = freq * i * j;
 668                        if (temp > max || temp < min)
 669                                continue;
 670                        if (best == 0 || temp < best) {
 671                                best = temp;
 672                                pred = i;
 673                                postd = j;
 674                        }
 675                }
 676        }
 677
 678        if (best == 0) {
 679                printf("Fail to set rate to %dKHz", freq);
 680                return;
 681        }
 682
 683        debug("best %d, pred = %d, postd = %d\n", best, pred, postd);
 684
 685        pll_div = best / hck;
 686        pll_denom = 1000000;
 687        pll_num = (best - hck * pll_div) * pll_denom / hck;
 688
 689        /*
 690         *                                  pll_num
 691         *             (24MHz * (pll_div + --------- ))
 692         *                                 pll_denom
 693         *freq KHz =  --------------------------------
 694         *             post_div * pred * postd * 1000
 695         */
 696
 697        if (base_addr == LCDIF1_BASE_ADDR) {
 698                if (enable_pll_video(pll_div, pll_num, pll_denom, post_div))
 699                        return;
 700
 701                /* Select pre-lcd clock to PLL5 and set pre divider */
 702                clrsetbits_le32(&imx_ccm->cscdr2,
 703                                MXC_CCM_CSCDR2_LCDIF1_PRED_SEL_MASK |
 704                                MXC_CCM_CSCDR2_LCDIF1_PRE_DIV_MASK,
 705                                (0x2 << MXC_CCM_CSCDR2_LCDIF1_PRED_SEL_OFFSET) |
 706                                ((pred - 1) <<
 707                                 MXC_CCM_CSCDR2_LCDIF1_PRE_DIV_OFFSET));
 708
 709                /* Set the post divider */
 710                clrsetbits_le32(&imx_ccm->cbcmr,
 711                                MXC_CCM_CBCMR_LCDIF1_PODF_MASK,
 712                                ((postd - 1) <<
 713                                 MXC_CCM_CBCMR_LCDIF1_PODF_OFFSET));
 714        } else if (is_cpu_type(MXC_CPU_MX6SX)) {
 715                /* Setting LCDIF2 for i.MX6SX */
 716                if (enable_pll_video(pll_div, pll_num, pll_denom, post_div))
 717                        return;
 718
 719                /* Select pre-lcd clock to PLL5 and set pre divider */
 720                clrsetbits_le32(&imx_ccm->cscdr2,
 721                                MXC_CCM_CSCDR2_LCDIF2_PRED_SEL_MASK |
 722                                MXC_CCM_CSCDR2_LCDIF2_PRE_DIV_MASK,
 723                                (0x2 << MXC_CCM_CSCDR2_LCDIF2_PRED_SEL_OFFSET) |
 724                                ((pred - 1) <<
 725                                 MXC_CCM_CSCDR2_LCDIF2_PRE_DIV_OFFSET));
 726
 727                /* Set the post divider */
 728                clrsetbits_le32(&imx_ccm->cscmr1,
 729                                MXC_CCM_CSCMR1_LCDIF2_PODF_MASK,
 730                                ((postd - 1) <<
 731                                 MXC_CCM_CSCMR1_LCDIF2_PODF_OFFSET));
 732        }
 733}
 734
 735int enable_lcdif_clock(u32 base_addr)
 736{
 737        u32 reg = 0;
 738        u32 lcdif_clk_sel_mask, lcdif_ccgr3_mask;
 739
 740        if (is_cpu_type(MXC_CPU_MX6SX)) {
 741                if ((base_addr != LCDIF1_BASE_ADDR) &&
 742                    (base_addr != LCDIF2_BASE_ADDR)) {
 743                        puts("Wrong LCD interface!\n");
 744                        return -EINVAL;
 745                }
 746                /* Set to pre-mux clock at default */
 747                lcdif_clk_sel_mask = (base_addr == LCDIF2_BASE_ADDR) ?
 748                        MXC_CCM_CSCDR2_LCDIF2_CLK_SEL_MASK :
 749                        MXC_CCM_CSCDR2_LCDIF1_CLK_SEL_MASK;
 750                lcdif_ccgr3_mask = (base_addr == LCDIF2_BASE_ADDR) ?
 751                        (MXC_CCM_CCGR3_LCDIF2_PIX_MASK |
 752                         MXC_CCM_CCGR3_DISP_AXI_MASK) :
 753                        (MXC_CCM_CCGR3_LCDIF1_PIX_MASK |
 754                         MXC_CCM_CCGR3_DISP_AXI_MASK);
 755        } else if (is_cpu_type(MXC_CPU_MX6UL)) {
 756                if (base_addr != LCDIF1_BASE_ADDR) {
 757                        puts("Wrong LCD interface!\n");
 758                        return -EINVAL;
 759                }
 760                /* Set to pre-mux clock at default */
 761                lcdif_clk_sel_mask = MXC_CCM_CSCDR2_LCDIF1_CLK_SEL_MASK;
 762                lcdif_ccgr3_mask =  MXC_CCM_CCGR3_LCDIF1_PIX_MASK;
 763        } else {
 764                return 0;
 765        }
 766
 767        reg = readl(&imx_ccm->cscdr2);
 768        reg &= ~lcdif_clk_sel_mask;
 769        writel(reg, &imx_ccm->cscdr2);
 770
 771        /* Enable the LCDIF pix clock */
 772        reg = readl(&imx_ccm->CCGR3);
 773        reg |= lcdif_ccgr3_mask;
 774        writel(reg, &imx_ccm->CCGR3);
 775
 776        reg = readl(&imx_ccm->CCGR2);
 777        reg |= MXC_CCM_CCGR2_LCD_MASK;
 778        writel(reg, &imx_ccm->CCGR2);
 779
 780        return 0;
 781}
 782#endif
 783
 784#ifdef CONFIG_FSL_QSPI
 785/* qspi_num can be from 0 - 1 */
 786void enable_qspi_clk(int qspi_num)
 787{
 788        u32 reg = 0;
 789        /* Enable QuadSPI clock */
 790        switch (qspi_num) {
 791        case 0:
 792                /* disable the clock gate */
 793                clrbits_le32(&imx_ccm->CCGR3, MXC_CCM_CCGR3_QSPI1_MASK);
 794
 795                /* set 50M  : (50 = 396 / 2 / 4) */
 796                reg = readl(&imx_ccm->cscmr1);
 797                reg &= ~(MXC_CCM_CSCMR1_QSPI1_PODF_MASK |
 798                         MXC_CCM_CSCMR1_QSPI1_CLK_SEL_MASK);
 799                reg |= ((1 << MXC_CCM_CSCMR1_QSPI1_PODF_OFFSET) |
 800                        (2 << MXC_CCM_CSCMR1_QSPI1_CLK_SEL_OFFSET));
 801                writel(reg, &imx_ccm->cscmr1);
 802
 803                /* enable the clock gate */
 804                setbits_le32(&imx_ccm->CCGR3, MXC_CCM_CCGR3_QSPI1_MASK);
 805                break;
 806        case 1:
 807                /*
 808                 * disable the clock gate
 809                 * QSPI2 and GPMI_BCH_INPUT_GPMI_IO share the same clock gate,
 810                 * disable both of them.
 811                 */
 812                clrbits_le32(&imx_ccm->CCGR4, MXC_CCM_CCGR4_QSPI2_ENFC_MASK |
 813                             MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK);
 814
 815                /* set 50M  : (50 = 396 / 2 / 4) */
 816                reg = readl(&imx_ccm->cs2cdr);
 817                reg &= ~(MXC_CCM_CS2CDR_QSPI2_CLK_PODF_MASK |
 818                         MXC_CCM_CS2CDR_QSPI2_CLK_PRED_MASK |
 819                         MXC_CCM_CS2CDR_QSPI2_CLK_SEL_MASK);
 820                reg |= (MXC_CCM_CS2CDR_QSPI2_CLK_PRED(0x1) |
 821                        MXC_CCM_CS2CDR_QSPI2_CLK_SEL(0x3));
 822                writel(reg, &imx_ccm->cs2cdr);
 823
 824                /*enable the clock gate*/
 825                setbits_le32(&imx_ccm->CCGR4, MXC_CCM_CCGR4_QSPI2_ENFC_MASK |
 826                             MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK);
 827                break;
 828        default:
 829                break;
 830        }
 831}
 832#endif
 833
 834#ifdef CONFIG_FEC_MXC
 835int enable_fec_anatop_clock(int fec_id, enum enet_freq freq)
 836{
 837        u32 reg = 0;
 838        s32 timeout = 100000;
 839
 840        struct anatop_regs __iomem *anatop =
 841                (struct anatop_regs __iomem *)ANATOP_BASE_ADDR;
 842
 843        if (freq < ENET_25MHZ || freq > ENET_125MHZ)
 844                return -EINVAL;
 845
 846        reg = readl(&anatop->pll_enet);
 847
 848        if (fec_id == 0) {
 849                reg &= ~BM_ANADIG_PLL_ENET_DIV_SELECT;
 850                reg |= BF_ANADIG_PLL_ENET_DIV_SELECT(freq);
 851        } else if (fec_id == 1) {
 852                /* Only i.MX6SX/UL support ENET2 */
 853                if (!(is_cpu_type(MXC_CPU_MX6SX) ||
 854                      is_cpu_type(MXC_CPU_MX6UL)))
 855                        return -EINVAL;
 856                reg &= ~BM_ANADIG_PLL_ENET2_DIV_SELECT;
 857                reg |= BF_ANADIG_PLL_ENET2_DIV_SELECT(freq);
 858        } else {
 859                return -EINVAL;
 860        }
 861
 862        if ((reg & BM_ANADIG_PLL_ENET_POWERDOWN) ||
 863            (!(reg & BM_ANADIG_PLL_ENET_LOCK))) {
 864                reg &= ~BM_ANADIG_PLL_ENET_POWERDOWN;
 865                writel(reg, &anatop->pll_enet);
 866                while (timeout--) {
 867                        if (readl(&anatop->pll_enet) & BM_ANADIG_PLL_ENET_LOCK)
 868                                break;
 869                }
 870                if (timeout < 0)
 871                        return -ETIMEDOUT;
 872        }
 873
 874        /* Enable FEC clock */
 875        if (fec_id == 0)
 876                reg |= BM_ANADIG_PLL_ENET_ENABLE;
 877        else
 878                reg |= BM_ANADIG_PLL_ENET2_ENABLE;
 879        reg &= ~BM_ANADIG_PLL_ENET_BYPASS;
 880        writel(reg, &anatop->pll_enet);
 881
 882#ifdef CONFIG_MX6SX
 883        /*
 884         * Set enet ahb clock to 200MHz
 885         * pll2_pfd2_396m-> ENET_PODF-> ENET_AHB
 886         */
 887        reg = readl(&imx_ccm->chsccdr);
 888        reg &= ~(MXC_CCM_CHSCCDR_ENET_PRE_CLK_SEL_MASK
 889                 | MXC_CCM_CHSCCDR_ENET_PODF_MASK
 890                 | MXC_CCM_CHSCCDR_ENET_CLK_SEL_MASK);
 891        /* PLL2 PFD2 */
 892        reg |= (4 << MXC_CCM_CHSCCDR_ENET_PRE_CLK_SEL_OFFSET);
 893        /* Div = 2*/
 894        reg |= (1 << MXC_CCM_CHSCCDR_ENET_PODF_OFFSET);
 895        reg |= (0 << MXC_CCM_CHSCCDR_ENET_CLK_SEL_OFFSET);
 896        writel(reg, &imx_ccm->chsccdr);
 897
 898        /* Enable enet system clock */
 899        reg = readl(&imx_ccm->CCGR3);
 900        reg |= MXC_CCM_CCGR3_ENET_MASK;
 901        writel(reg, &imx_ccm->CCGR3);
 902#endif
 903        return 0;
 904}
 905#endif
 906
 907static u32 get_usdhc_clk(u32 port)
 908{
 909        u32 root_freq = 0, usdhc_podf = 0, clk_sel = 0;
 910        u32 cscmr1 = __raw_readl(&imx_ccm->cscmr1);
 911        u32 cscdr1 = __raw_readl(&imx_ccm->cscdr1);
 912
 913        switch (port) {
 914        case 0:
 915                usdhc_podf = (cscdr1 & MXC_CCM_CSCDR1_USDHC1_PODF_MASK) >>
 916                                        MXC_CCM_CSCDR1_USDHC1_PODF_OFFSET;
 917                clk_sel = cscmr1 & MXC_CCM_CSCMR1_USDHC1_CLK_SEL;
 918
 919                break;
 920        case 1:
 921                usdhc_podf = (cscdr1 & MXC_CCM_CSCDR1_USDHC2_PODF_MASK) >>
 922                                        MXC_CCM_CSCDR1_USDHC2_PODF_OFFSET;
 923                clk_sel = cscmr1 & MXC_CCM_CSCMR1_USDHC2_CLK_SEL;
 924
 925                break;
 926        case 2:
 927                usdhc_podf = (cscdr1 & MXC_CCM_CSCDR1_USDHC3_PODF_MASK) >>
 928                                        MXC_CCM_CSCDR1_USDHC3_PODF_OFFSET;
 929                clk_sel = cscmr1 & MXC_CCM_CSCMR1_USDHC3_CLK_SEL;
 930
 931                break;
 932        case 3:
 933                usdhc_podf = (cscdr1 & MXC_CCM_CSCDR1_USDHC4_PODF_MASK) >>
 934                                        MXC_CCM_CSCDR1_USDHC4_PODF_OFFSET;
 935                clk_sel = cscmr1 & MXC_CCM_CSCMR1_USDHC4_CLK_SEL;
 936
 937                break;
 938        default:
 939                break;
 940        }
 941
 942        if (clk_sel)
 943                root_freq = mxc_get_pll_pfd(PLL_BUS, 0);
 944        else
 945                root_freq = mxc_get_pll_pfd(PLL_BUS, 2);
 946
 947        return root_freq / (usdhc_podf + 1);
 948}
 949
 950u32 imx_get_uartclk(void)
 951{
 952        return get_uart_clk();
 953}
 954
 955u32 imx_get_fecclk(void)
 956{
 957        return mxc_get_clock(MXC_IPG_CLK);
 958}
 959
 960#if defined(CONFIG_CMD_SATA) || defined(CONFIG_PCIE_IMX)
 961static int enable_enet_pll(uint32_t en)
 962{
 963        struct mxc_ccm_reg *const imx_ccm
 964                = (struct mxc_ccm_reg *) CCM_BASE_ADDR;
 965        s32 timeout = 100000;
 966        u32 reg = 0;
 967
 968        /* Enable PLLs */
 969        reg = readl(&imx_ccm->analog_pll_enet);
 970        reg &= ~BM_ANADIG_PLL_SYS_POWERDOWN;
 971        writel(reg, &imx_ccm->analog_pll_enet);
 972        reg |= BM_ANADIG_PLL_SYS_ENABLE;
 973        while (timeout--) {
 974                if (readl(&imx_ccm->analog_pll_enet) & BM_ANADIG_PLL_SYS_LOCK)
 975                        break;
 976        }
 977        if (timeout <= 0)
 978                return -EIO;
 979        reg &= ~BM_ANADIG_PLL_SYS_BYPASS;
 980        writel(reg, &imx_ccm->analog_pll_enet);
 981        reg |= en;
 982        writel(reg, &imx_ccm->analog_pll_enet);
 983        return 0;
 984}
 985#endif
 986
 987#ifdef CONFIG_CMD_SATA
 988static void ungate_sata_clock(void)
 989{
 990        struct mxc_ccm_reg *const imx_ccm =
 991                (struct mxc_ccm_reg *)CCM_BASE_ADDR;
 992
 993        /* Enable SATA clock. */
 994        setbits_le32(&imx_ccm->CCGR5, MXC_CCM_CCGR5_SATA_MASK);
 995}
 996
 997int enable_sata_clock(void)
 998{
 999        ungate_sata_clock();
1000        return enable_enet_pll(BM_ANADIG_PLL_ENET_ENABLE_SATA);
1001}
1002
1003void disable_sata_clock(void)
1004{
1005        struct mxc_ccm_reg *const imx_ccm =
1006                (struct mxc_ccm_reg *)CCM_BASE_ADDR;
1007
1008        clrbits_le32(&imx_ccm->CCGR5, MXC_CCM_CCGR5_SATA_MASK);
1009}
1010#endif
1011
1012#ifdef CONFIG_PCIE_IMX
1013static void ungate_pcie_clock(void)
1014{
1015        struct mxc_ccm_reg *const imx_ccm =
1016                (struct mxc_ccm_reg *)CCM_BASE_ADDR;
1017
1018        /* Enable PCIe clock. */
1019        setbits_le32(&imx_ccm->CCGR4, MXC_CCM_CCGR4_PCIE_MASK);
1020}
1021
1022int enable_pcie_clock(void)
1023{
1024        struct anatop_regs *anatop_regs =
1025                (struct anatop_regs *)ANATOP_BASE_ADDR;
1026        struct mxc_ccm_reg *ccm_regs = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
1027        u32 lvds1_clk_sel;
1028
1029        /*
1030         * Here be dragons!
1031         *
1032         * The register ANATOP_MISC1 is not documented in the Freescale
1033         * MX6RM. The register that is mapped in the ANATOP space and
1034         * marked as ANATOP_MISC1 is actually documented in the PMU section
1035         * of the datasheet as PMU_MISC1.
1036         *
1037         * Switch LVDS clock source to SATA (0xb) on mx6q/dl or PCI (0xa) on
1038         * mx6sx, disable clock INPUT and enable clock OUTPUT. This is important
1039         * for PCI express link that is clocked from the i.MX6.
1040         */
1041#define ANADIG_ANA_MISC1_LVDSCLK1_IBEN          (1 << 12)
1042#define ANADIG_ANA_MISC1_LVDSCLK1_OBEN          (1 << 10)
1043#define ANADIG_ANA_MISC1_LVDS1_CLK_SEL_MASK     0x0000001F
1044#define ANADIG_ANA_MISC1_LVDS1_CLK_SEL_PCIE_REF 0xa
1045#define ANADIG_ANA_MISC1_LVDS1_CLK_SEL_SATA_REF 0xb
1046
1047        if (is_cpu_type(MXC_CPU_MX6SX))
1048                lvds1_clk_sel = ANADIG_ANA_MISC1_LVDS1_CLK_SEL_PCIE_REF;
1049        else
1050                lvds1_clk_sel = ANADIG_ANA_MISC1_LVDS1_CLK_SEL_SATA_REF;
1051
1052        clrsetbits_le32(&anatop_regs->ana_misc1,
1053                        ANADIG_ANA_MISC1_LVDSCLK1_IBEN |
1054                        ANADIG_ANA_MISC1_LVDS1_CLK_SEL_MASK,
1055                        ANADIG_ANA_MISC1_LVDSCLK1_OBEN | lvds1_clk_sel);
1056
1057        /* PCIe reference clock sourced from AXI. */
1058        clrbits_le32(&ccm_regs->cbcmr, MXC_CCM_CBCMR_PCIE_AXI_CLK_SEL);
1059
1060        /* Party time! Ungate the clock to the PCIe. */
1061#ifdef CONFIG_CMD_SATA
1062        ungate_sata_clock();
1063#endif
1064        ungate_pcie_clock();
1065
1066        return enable_enet_pll(BM_ANADIG_PLL_ENET_ENABLE_SATA |
1067                               BM_ANADIG_PLL_ENET_ENABLE_PCIE);
1068}
1069#endif
1070
1071#ifdef CONFIG_SECURE_BOOT
1072void hab_caam_clock_enable(unsigned char enable)
1073{
1074        u32 reg;
1075
1076        /* CG4 ~ CG6, CAAM clocks */
1077        reg = __raw_readl(&imx_ccm->CCGR0);
1078        if (enable)
1079                reg |= (MXC_CCM_CCGR0_CAAM_WRAPPER_IPG_MASK |
1080                        MXC_CCM_CCGR0_CAAM_WRAPPER_ACLK_MASK |
1081                        MXC_CCM_CCGR0_CAAM_SECURE_MEM_MASK);
1082        else
1083                reg &= ~(MXC_CCM_CCGR0_CAAM_WRAPPER_IPG_MASK |
1084                        MXC_CCM_CCGR0_CAAM_WRAPPER_ACLK_MASK |
1085                        MXC_CCM_CCGR0_CAAM_SECURE_MEM_MASK);
1086        __raw_writel(reg, &imx_ccm->CCGR0);
1087
1088        /* EMI slow clk */
1089        reg = __raw_readl(&imx_ccm->CCGR6);
1090        if (enable)
1091                reg |= MXC_CCM_CCGR6_EMI_SLOW_MASK;
1092        else
1093                reg &= ~MXC_CCM_CCGR6_EMI_SLOW_MASK;
1094        __raw_writel(reg, &imx_ccm->CCGR6);
1095}
1096#endif
1097
1098static void enable_pll3(void)
1099{
1100        struct anatop_regs __iomem *anatop =
1101                (struct anatop_regs __iomem *)ANATOP_BASE_ADDR;
1102
1103        /* make sure pll3 is enabled */
1104        if ((readl(&anatop->usb1_pll_480_ctrl) &
1105                        BM_ANADIG_USB1_PLL_480_CTRL_LOCK) == 0) {
1106                /* enable pll's power */
1107                writel(BM_ANADIG_USB1_PLL_480_CTRL_POWER,
1108                       &anatop->usb1_pll_480_ctrl_set);
1109                writel(0x80, &anatop->ana_misc2_clr);
1110                /* wait for pll lock */
1111                while ((readl(&anatop->usb1_pll_480_ctrl) &
1112                        BM_ANADIG_USB1_PLL_480_CTRL_LOCK) == 0)
1113                        ;
1114                /* disable bypass */
1115                writel(BM_ANADIG_USB1_PLL_480_CTRL_BYPASS,
1116                       &anatop->usb1_pll_480_ctrl_clr);
1117                /* enable pll output */
1118                writel(BM_ANADIG_USB1_PLL_480_CTRL_ENABLE,
1119                       &anatop->usb1_pll_480_ctrl_set);
1120        }
1121}
1122
1123void enable_thermal_clk(void)
1124{
1125        enable_pll3();
1126}
1127
1128unsigned int mxc_get_clock(enum mxc_clock clk)
1129{
1130        switch (clk) {
1131        case MXC_ARM_CLK:
1132                return get_mcu_main_clk();
1133        case MXC_PER_CLK:
1134                return get_periph_clk();
1135        case MXC_AHB_CLK:
1136                return get_ahb_clk();
1137        case MXC_IPG_CLK:
1138                return get_ipg_clk();
1139        case MXC_IPG_PERCLK:
1140        case MXC_I2C_CLK:
1141                return get_ipg_per_clk();
1142        case MXC_UART_CLK:
1143                return get_uart_clk();
1144        case MXC_CSPI_CLK:
1145                return get_cspi_clk();
1146        case MXC_AXI_CLK:
1147                return get_axi_clk();
1148        case MXC_EMI_SLOW_CLK:
1149                return get_emi_slow_clk();
1150        case MXC_DDR_CLK:
1151                return get_mmdc_ch0_clk();
1152        case MXC_ESDHC_CLK:
1153                return get_usdhc_clk(0);
1154        case MXC_ESDHC2_CLK:
1155                return get_usdhc_clk(1);
1156        case MXC_ESDHC3_CLK:
1157                return get_usdhc_clk(2);
1158        case MXC_ESDHC4_CLK:
1159                return get_usdhc_clk(3);
1160        case MXC_SATA_CLK:
1161                return get_ahb_clk();
1162        default:
1163                printf("Unsupported MXC CLK: %d\n", clk);
1164                break;
1165        }
1166
1167        return 0;
1168}
1169
1170/*
1171 * Dump some core clockes.
1172 */
1173int do_mx6_showclocks(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
1174{
1175        u32 freq;
1176        freq = decode_pll(PLL_SYS, MXC_HCLK);
1177        printf("PLL_SYS    %8d MHz\n", freq / 1000000);
1178        freq = decode_pll(PLL_BUS, MXC_HCLK);
1179        printf("PLL_BUS    %8d MHz\n", freq / 1000000);
1180        freq = decode_pll(PLL_USBOTG, MXC_HCLK);
1181        printf("PLL_OTG    %8d MHz\n", freq / 1000000);
1182        freq = decode_pll(PLL_ENET, MXC_HCLK);
1183        printf("PLL_NET    %8d MHz\n", freq / 1000000);
1184
1185        printf("\n");
1186        printf("IPG        %8d kHz\n", mxc_get_clock(MXC_IPG_CLK) / 1000);
1187        printf("UART       %8d kHz\n", mxc_get_clock(MXC_UART_CLK) / 1000);
1188#ifdef CONFIG_MXC_SPI
1189        printf("CSPI       %8d kHz\n", mxc_get_clock(MXC_CSPI_CLK) / 1000);
1190#endif
1191        printf("AHB        %8d kHz\n", mxc_get_clock(MXC_AHB_CLK) / 1000);
1192        printf("AXI        %8d kHz\n", mxc_get_clock(MXC_AXI_CLK) / 1000);
1193        printf("DDR        %8d kHz\n", mxc_get_clock(MXC_DDR_CLK) / 1000);
1194        printf("USDHC1     %8d kHz\n", mxc_get_clock(MXC_ESDHC_CLK) / 1000);
1195        printf("USDHC2     %8d kHz\n", mxc_get_clock(MXC_ESDHC2_CLK) / 1000);
1196        printf("USDHC3     %8d kHz\n", mxc_get_clock(MXC_ESDHC3_CLK) / 1000);
1197        printf("USDHC4     %8d kHz\n", mxc_get_clock(MXC_ESDHC4_CLK) / 1000);
1198        printf("EMI SLOW   %8d kHz\n", mxc_get_clock(MXC_EMI_SLOW_CLK) / 1000);
1199        printf("IPG PERCLK %8d kHz\n", mxc_get_clock(MXC_IPG_PERCLK) / 1000);
1200
1201        return 0;
1202}
1203
1204#ifndef CONFIG_MX6SX
1205void enable_ipu_clock(void)
1206{
1207        struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
1208        int reg;
1209        reg = readl(&mxc_ccm->CCGR3);
1210        reg |= MXC_CCM_CCGR3_IPU1_IPU_MASK;
1211        writel(reg, &mxc_ccm->CCGR3);
1212
1213        if (is_mx6dqp()) {
1214                setbits_le32(&mxc_ccm->CCGR6, MXC_CCM_CCGR6_PRG_CLK0_MASK);
1215                setbits_le32(&mxc_ccm->CCGR3, MXC_CCM_CCGR3_IPU2_IPU_MASK);
1216        }
1217}
1218#endif
1219/***************************************************/
1220
1221U_BOOT_CMD(
1222        clocks, CONFIG_SYS_MAXARGS, 1, do_mx6_showclocks,
1223        "display clocks",
1224        ""
1225);
1226