LXR uboot/board/keymile/kmp204x/eth.c

   1/*
   2 * (C) Copyright 2013 Keymile AG
   3 * Valentin Longchamp <valentin.longchamp@keymile.com>
   4 *
   5 * SPDX-License-Identifier:     GPL-2.0+
   6 */
   7
   8#include <common.h>
   9#include <netdev.h>
  10#include <fm_eth.h>
  11#include <fsl_mdio.h>
  12#include <phy.h>
  13
  14int board_eth_init(bd_t *bis)
  15{
  16        int ret = 0;
  17#ifdef CONFIG_FMAN_ENET
  18        struct fsl_pq_mdio_info dtsec_mdio_info;
  19
  20        printf("Initializing Fman\n");
  21
  22        dtsec_mdio_info.regs =
  23                (struct tsec_mii_mng *)CONFIG_SYS_FM1_DTSEC1_MDIO_ADDR;
  24        dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
  25
  26        /* Register the real 1G MDIO bus */
  27        fsl_pq_mdio_init(bis, &dtsec_mdio_info);
  28
  29        /* DTESC1/2 don't have a PHY, they are temporarily disabled
  30         * so that u-boot doesn't try to unsuccessfuly enable them */
  31        fm_disable_port(FM1_DTSEC1);
  32        fm_disable_port(FM1_DTSEC2);
  33
  34        /*
  35         * Program RGMII DTSEC5 (FM1 MAC5) on the EC2 physical itf
  36         * This is the debug interface, the only one used in u-boot
  37         */
  38        fm_info_set_phy_address(FM1_DTSEC5, CONFIG_SYS_FM1_DTSEC5_PHY_ADDR);
  39        fm_info_set_mdio(FM1_DTSEC5,
  40                         miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME));
  41
  42        ret = cpu_eth_init(bis);
  43
  44        /* reenable DTSEC1/2 for later (kernel) */
  45        fm_enable_port(FM1_DTSEC1);
  46        fm_enable_port(FM1_DTSEC2);
  47#endif
  48
  49        return ret;
  50}
  51
  52#if defined(CONFIG_PHYLIB) && defined(CONFIG_PHY_MARVELL)
  53
  54#define mv88E1118_PAGE_REG      22
  55
  56int board_phy_config(struct phy_device *phydev)
  57{
  58        if (phydev->addr == CONFIG_SYS_FM1_DTSEC5_PHY_ADDR) {
  59                /* driver config is good */
  60                if (phydev->drv->config)
  61                        phydev->drv->config(phydev);
  62
  63                /* but we still need to fix the LEDs */
  64                phy_write(phydev, MDIO_DEVAD_NONE, mv88E1118_PAGE_REG, 0x0003);
  65                phy_write(phydev, MDIO_DEVAD_NONE, 0x10, 0x0840);
  66                phy_write(phydev, MDIO_DEVAD_NONE, mv88E1118_PAGE_REG, 0x0000);
  67        }
  68
  69        return 0;
  70}
  71#endif
  72