LXR uboot/drivers/i2c/zynq

   1/*
   2 * Driver for the Zynq-7000 PS I2C controller
   3 * IP from Cadence (ID T-CS-PE-0007-100, Version R1p10f2)
   4 *
   5 * Author: Joe Hershberger <joe.hershberger@ni.com>
   6 * Copyright (c) 2012 Joe Hershberger.
   7 *
   8 * Copyright (c) 2012-2013 Xilinx, Michal Simek
   9 *
  10 * SPDX-License-Identifier:     GPL-2.0+
  11 */
  12
  13#include <common.h>
  14#include <asm/io.h>
  15#include <i2c.h>
  16#include <asm/errno.h>
  17#include <asm/arch/hardware.h>
  18
  19/* i2c register set */
  20struct zynq_i2c_registers {
  21        u32 control;
  22        u32 status;
  23        u32 address;
  24        u32 data;
  25        u32 interrupt_status;
  26        u32 transfer_size;
  27        u32 slave_mon_pause;
  28        u32 time_out;
  29        u32 interrupt_mask;
  30        u32 interrupt_enable;
  31        u32 interrupt_disable;
  32};
  33
  34/* Control register fields */
  35#define ZYNQ_I2C_CONTROL_RW             0x00000001
  36#define ZYNQ_I2C_CONTROL_MS             0x00000002
  37#define ZYNQ_I2C_CONTROL_NEA            0x00000004
  38#define ZYNQ_I2C_CONTROL_ACKEN          0x00000008
  39#define ZYNQ_I2C_CONTROL_HOLD           0x00000010
  40#define ZYNQ_I2C_CONTROL_SLVMON         0x00000020
  41#define ZYNQ_I2C_CONTROL_CLR_FIFO       0x00000040
  42#define ZYNQ_I2C_CONTROL_DIV_B_SHIFT    8
  43#define ZYNQ_I2C_CONTROL_DIV_B_MASK     0x00003F00
  44#define ZYNQ_I2C_CONTROL_DIV_A_SHIFT    14
  45#define ZYNQ_I2C_CONTROL_DIV_A_MASK     0x0000C000
  46
  47/* Status register values */
  48#define ZYNQ_I2C_STATUS_RXDV    0x00000020
  49#define ZYNQ_I2C_STATUS_TXDV    0x00000040
  50#define ZYNQ_I2C_STATUS_RXOVF   0x00000080
  51#define ZYNQ_I2C_STATUS_BA      0x00000100
  52
  53/* Interrupt register fields */
  54#define ZYNQ_I2C_INTERRUPT_COMP         0x00000001
  55#define ZYNQ_I2C_INTERRUPT_DATA         0x00000002
  56#define ZYNQ_I2C_INTERRUPT_NACK         0x00000004
  57#define ZYNQ_I2C_INTERRUPT_TO           0x00000008
  58#define ZYNQ_I2C_INTERRUPT_SLVRDY       0x00000010
  59#define ZYNQ_I2C_INTERRUPT_RXOVF        0x00000020
  60#define ZYNQ_I2C_INTERRUPT_TXOVF        0x00000040
  61#define ZYNQ_I2C_INTERRUPT_RXUNF        0x00000080
  62#define ZYNQ_I2C_INTERRUPT_ARBLOST      0x00000200
  63
  64#define ZYNQ_I2C_FIFO_DEPTH             16
  65#define ZYNQ_I2C_TRANSFERT_SIZE_MAX     255 /* Controller transfer limit */
  66
  67static struct zynq_i2c_registers *i2c_select(struct i2c_adapter *adap)
  68{
  69        return adap->hwadapnr ?
  70                /* Zynq PS I2C1 */
  71                (struct zynq_i2c_registers *)ZYNQ_I2C_BASEADDR1 :
  72                /* Zynq PS I2C0 */
  73                (struct zynq_i2c_registers *)ZYNQ_I2C_BASEADDR0;
  74}
  75
  76/* I2C init called by cmd_i2c when doing 'i2c reset'. */
  77static void zynq_i2c_init(struct i2c_adapter *adap, int requested_speed,
  78                          int slaveadd)
  79{
  80        struct zynq_i2c_registers *zynq_i2c = i2c_select(adap);
  81
  82        /* 111MHz / ( (3 * 17) * 22 ) = ~100KHz */
  83        writel((16 << ZYNQ_I2C_CONTROL_DIV_B_SHIFT) |
  84                (2 << ZYNQ_I2C_CONTROL_DIV_A_SHIFT), &zynq_i2c->control);
  85
  86        /* Enable master mode, ack, and 7-bit addressing */
  87        setbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_MS |
  88                ZYNQ_I2C_CONTROL_ACKEN | ZYNQ_I2C_CONTROL_NEA);
  89}
  90
  91#ifdef DEBUG
  92static void zynq_i2c_debug_status(struct zynq_i2c_registers *zynq_i2c)
  93{
  94        int int_status;
  95        int status;
  96        int_status = readl(&zynq_i2c->interrupt_status);
  97
  98        status = readl(&zynq_i2c->status);
  99        if (int_status || status) {
 100                debug("Status: ");
 101                if (int_status & ZYNQ_I2C_INTERRUPT_COMP)
 102                        debug("COMP ");
 103                if (int_status & ZYNQ_I2C_INTERRUPT_DATA)
 104                        debug("DATA ");
 105                if (int_status & ZYNQ_I2C_INTERRUPT_NACK)
 106                        debug("NACK ");
 107                if (int_status & ZYNQ_I2C_INTERRUPT_TO)
 108                        debug("TO ");
 109                if (int_status & ZYNQ_I2C_INTERRUPT_SLVRDY)
 110                        debug("SLVRDY ");
 111                if (int_status & ZYNQ_I2C_INTERRUPT_RXOVF)
 112                        debug("RXOVF ");
 113                if (int_status & ZYNQ_I2C_INTERRUPT_TXOVF)
 114                        debug("TXOVF ");
 115                if (int_status & ZYNQ_I2C_INTERRUPT_RXUNF)
 116                        debug("RXUNF ");
 117                if (int_status & ZYNQ_I2C_INTERRUPT_ARBLOST)
 118                        debug("ARBLOST ");
 119                if (status & ZYNQ_I2C_STATUS_RXDV)
 120                        debug("RXDV ");
 121                if (status & ZYNQ_I2C_STATUS_TXDV)
 122                        debug("TXDV ");
 123                if (status & ZYNQ_I2C_STATUS_RXOVF)
 124                        debug("RXOVF ");
 125                if (status & ZYNQ_I2C_STATUS_BA)
 126                        debug("BA ");
 127                debug("TS%d ", readl(&zynq_i2c->transfer_size));
 128                debug("\n");
 129        }
 130}
 131#endif
 132
 133/* Wait for an interrupt */
 134static u32 zynq_i2c_wait(struct zynq_i2c_registers *zynq_i2c, u32 mask)
 135{
 136        int timeout, int_status;
 137
 138        for (timeout = 0; timeout < 100; timeout++) {
 139                udelay(100);
 140                int_status = readl(&zynq_i2c->interrupt_status);
 141                if (int_status & mask)
 142                        break;
 143        }
 144#ifdef DEBUG
 145        zynq_i2c_debug_status(zynq_i2c);
 146#endif
 147        /* Clear interrupt status flags */
 148        writel(int_status & mask, &zynq_i2c->interrupt_status);
 149
 150        return int_status & mask;
 151}
 152
 153/*
 154 * I2C probe called by cmd_i2c when doing 'i2c probe'.
 155 * Begin read, nak data byte, end.
 156 */
 157static int zynq_i2c_probe(struct i2c_adapter *adap, u8 dev)
 158{
 159        struct zynq_i2c_registers *zynq_i2c = i2c_select(adap);
 160
 161        /* Attempt to read a byte */
 162        setbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_CLR_FIFO |
 163                ZYNQ_I2C_CONTROL_RW);
 164        clrbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_HOLD);
 165        writel(0xFF, &zynq_i2c->interrupt_status);
 166        writel(dev, &zynq_i2c->address);
 167        writel(1, &zynq_i2c->transfer_size);
 168
 169        return (zynq_i2c_wait(zynq_i2c, ZYNQ_I2C_INTERRUPT_COMP |
 170                ZYNQ_I2C_INTERRUPT_NACK) &
 171                ZYNQ_I2C_INTERRUPT_COMP) ? 0 : -ETIMEDOUT;
 172}
 173
 174/*
 175 * I2C read called by cmd_i2c when doing 'i2c read' and by cmd_eeprom.c
 176 * Begin write, send address byte(s), begin read, receive data bytes, end.
 177 */
 178static int zynq_i2c_read(struct i2c_adapter *adap, u8 dev, uint addr,
 179                         int alen, u8 *data, int length)
 180{
 181        u32 status;
 182        u32 i = 0;
 183        u8 *cur_data = data;
 184        struct zynq_i2c_registers *zynq_i2c = i2c_select(adap);
 185
 186        /* Check the hardware can handle the requested bytes */
 187        if ((length < 0) || (length > ZYNQ_I2C_TRANSFERT_SIZE_MAX))
 188                return -EINVAL;
 189
 190        /* Write the register address */
 191        setbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_CLR_FIFO |
 192                ZYNQ_I2C_CONTROL_HOLD);
 193        /*
 194         * Temporarily disable restart (by clearing hold)
 195         * It doesn't seem to work.
 196         */
 197        clrbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_HOLD);
 198        writel(0xFF, &zynq_i2c->interrupt_status);
 199        if (alen) {
 200                clrbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_RW);
 201                writel(dev, &zynq_i2c->address);
 202                while (alen--)
 203                        writel(addr >> (8 * alen), &zynq_i2c->data);
 204
 205                /* Wait for the address to be sent */
 206                if (!zynq_i2c_wait(zynq_i2c, ZYNQ_I2C_INTERRUPT_COMP)) {
 207                        /* Release the bus */
 208                        clrbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_HOLD);
 209                        return -ETIMEDOUT;
 210                }
 211                debug("Device acked address\n");
 212        }
 213
 214        setbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_CLR_FIFO |
 215                ZYNQ_I2C_CONTROL_RW);
 216        /* Start reading data */
 217        writel(dev, &zynq_i2c->address);
 218        writel(length, &zynq_i2c->transfer_size);
 219
 220        /* Wait for data */
 221        do {
 222                status = zynq_i2c_wait(zynq_i2c, ZYNQ_I2C_INTERRUPT_COMP |
 223                        ZYNQ_I2C_INTERRUPT_DATA);
 224                if (!status) {
 225                        /* Release the bus */
 226                        clrbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_HOLD);
 227                        return -ETIMEDOUT;
 228                }
 229                debug("Read %d bytes\n",
 230                      length - readl(&zynq_i2c->transfer_size));
 231                for (; i < length - readl(&zynq_i2c->transfer_size); i++)
 232                        *(cur_data++) = readl(&zynq_i2c->data);
 233        } while (readl(&zynq_i2c->transfer_size) != 0);
 234        /* All done... release the bus */
 235        clrbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_HOLD);
 236
 237#ifdef DEBUG
 238        zynq_i2c_debug_status(zynq_i2c);
 239#endif
 240        return 0;
 241}
 242
 243/*
 244 * I2C write called by cmd_i2c when doing 'i2c write' and by cmd_eeprom.c
 245 * Begin write, send address byte(s), send data bytes, end.
 246 */
 247static int zynq_i2c_write(struct i2c_adapter *adap, u8 dev, uint addr,
 248                          int alen, u8 *data, int length)
 249{
 250        u8 *cur_data = data;
 251        struct zynq_i2c_registers *zynq_i2c = i2c_select(adap);
 252
 253        /* Write the register address */
 254        setbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_CLR_FIFO |
 255                ZYNQ_I2C_CONTROL_HOLD);
 256        clrbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_RW);
 257        writel(0xFF, &zynq_i2c->interrupt_status);
 258        writel(dev, &zynq_i2c->address);
 259        if (alen) {
 260                while (alen--)
 261                        writel(addr >> (8 * alen), &zynq_i2c->data);
 262                /* Start the tranfer */
 263                if (!zynq_i2c_wait(zynq_i2c, ZYNQ_I2C_INTERRUPT_COMP)) {
 264                        /* Release the bus */
 265                        clrbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_HOLD);
 266                        return -ETIMEDOUT;
 267                }
 268                debug("Device acked address\n");
 269        }
 270
 271        while (length--) {
 272                writel(*(cur_data++), &zynq_i2c->data);
 273                if (readl(&zynq_i2c->transfer_size) == ZYNQ_I2C_FIFO_DEPTH) {
 274                        if (!zynq_i2c_wait(zynq_i2c, ZYNQ_I2C_INTERRUPT_COMP)) {
 275                                /* Release the bus */
 276                                clrbits_le32(&zynq_i2c->control,
 277                                             ZYNQ_I2C_CONTROL_HOLD);
 278                                return -ETIMEDOUT;
 279                        }
 280                }
 281        }
 282
 283        /* All done... release the bus */
 284        clrbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_HOLD);
 285        /* Wait for the address and data to be sent */
 286        if (!zynq_i2c_wait(zynq_i2c, ZYNQ_I2C_INTERRUPT_COMP))
 287                return -ETIMEDOUT;
 288        return 0;
 289}
 290
 291static unsigned int zynq_i2c_set_bus_speed(struct i2c_adapter *adap,
 292                        unsigned int speed)
 293{
 294        if (speed != 1000000)
 295                return -EINVAL;
 296
 297        return 0;
 298}
 299
 300#ifdef CONFIG_ZYNQ_I2C0
 301U_BOOT_I2C_ADAP_COMPLETE(zynq_0, zynq_i2c_init, zynq_i2c_probe, zynq_i2c_read,
 302                         zynq_i2c_write, zynq_i2c_set_bus_speed,
 303                         CONFIG_SYS_I2C_ZYNQ_SPEED, CONFIG_SYS_I2C_ZYNQ_SLAVE,
 304                         0)
 305#endif
 306#ifdef CONFIG_ZYNQ_I2C1
 307U_BOOT_I2C_ADAP_COMPLETE(zynq_1, zynq_i2c_init, zynq_i2c_probe, zynq_i2c_read,
 308                         zynq_i2c_write, zynq_i2c_set_bus_speed,
 309                         CONFIG_SYS_I2C_ZYNQ_SPEED, CONFIG_SYS_I2C_ZYNQ_SLAVE,
 310                         1)
 311#endif
 312