1
2
3
4
5
6
7#ifndef __CONFIG_H
8#define __CONFIG_H
9
10
11#define CONFIG_SPL_BOARD_INIT
12
13#define CONFIG_SYS_NAND_U_BOOT_OFFS (14 * SZ_1M)
14
15
16#define CONFIG_CMD_SPL
17#define CONFIG_SYS_SPL_ARGS_ADDR 0x18000000
18#define CONFIG_CMD_SPL_WRITE_SIZE (128 * SZ_1K)
19
20
21#define CONFIG_CMD_SPL_NAND_OFS (17 * SZ_1M)
22#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS (18 * SZ_1M)
23
24
25#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x800
26#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS (CONFIG_CMD_SPL_WRITE_SIZE / 512)
27#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x1000
28
29#include "imx6_spl.h"
30#include "mx6_common.h"
31#define CONFIG_DISPLAY_BOARDINFO_LATE
32
33#define CONFIG_MACH_TYPE 4520
34
35
36#define CONFIG_SERIAL_TAG
37
38
39#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)
40
41
42#define CONFIG_BOARD_EARLY_INIT_F
43#define CONFIG_MISC_INIT_R
44
45
46#ifndef CONFIG_SPL_BUILD
47#define CONFIG_DM_GPIO
48#define CONFIG_DM_THERMAL
49#endif
50
51
52#define CONFIG_IMX_THERMAL
53
54
55#define CONFIG_MXC_UART
56#define CONFIG_MXC_UART_BASE UART2_BASE
57
58#ifdef CONFIG_SPI_FLASH
59
60
61#ifdef CONFIG_CMD_SF
62 #define CONFIG_MXC_SPI
63 #define CONFIG_SPI_FLASH_MTD
64 #define CONFIG_SPI_FLASH_BAR
65 #define CONFIG_SF_DEFAULT_BUS 0
66 #define CONFIG_SF_DEFAULT_CS 0
67
68 #define CONFIG_SF_DEFAULT_SPEED 30000000
69 #define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
70#endif
71
72#else
73
74#define CONFIG_CMD_NAND
75#define CONFIG_CMD_NAND_TRIMFFS
76#ifdef CONFIG_CMD_NAND
77 #define CONFIG_NAND_MXS
78 #define CONFIG_SYS_MAX_NAND_DEVICE 1
79 #define CONFIG_SYS_NAND_BASE 0x40000000
80 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
81 #define CONFIG_SYS_NAND_ONFI_DETECTION
82
83
84 #define CONFIG_APBH_DMA
85 #define CONFIG_APBH_DMA_BURST
86 #define CONFIG_APBH_DMA_BURST8
87#endif
88
89#endif
90
91
92#define CONFIG_SYS_I2C
93#define CONFIG_SYS_I2C_MXC
94#define CONFIG_SYS_I2C_MXC_I2C1
95#define CONFIG_SYS_I2C_MXC_I2C2
96#define CONFIG_SYS_I2C_MXC_I2C3
97#define CONFIG_SYS_I2C_SPEED 100000
98#define CONFIG_I2C_GSC 0
99#define CONFIG_I2C_PMIC 1
100#define CONFIG_I2C_EDID
101
102
103#define CONFIG_SYS_FSL_ESDHC_ADDR 0
104#define CONFIG_SYS_FSL_USDHC_NUM 1
105
106
107#define CONFIG_CMD_UBIFS
108
109
110
111
112#define CONFIG_CMD_SATA
113#ifdef CONFIG_CMD_SATA
114 #define CONFIG_DWC_AHSATA
115 #define CONFIG_SYS_SATA_MAX_DEVICE 1
116 #define CONFIG_DWC_AHSATA_PORT_ID 0
117 #define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
118 #define CONFIG_LBA48
119 #define CONFIG_LIBATA
120#endif
121
122
123
124
125#define CONFIG_CMD_PCI
126#ifdef CONFIG_CMD_PCI
127#define CONFIG_PCI_SCAN_SHOW
128#define CONFIG_PCI_FIXUP_DEV
129#define CONFIG_PCIE_IMX
130#endif
131
132
133
134
135#define CONFIG_POWER
136#define CONFIG_POWER_I2C
137#define CONFIG_POWER_PFUZE100
138#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
139#define CONFIG_POWER_LTC3676
140#define CONFIG_POWER_LTC3676_I2C_ADDR 0x3c
141
142
143#define CONFIG_CMD_BMODE
144#define CONFIG_CMD_HDMIDETECT
145#define CONFIG_CMD_GSC
146#define CONFIG_CMD_EECONFIG
147#define CONFIG_RBTREE
148
149
150#define CONFIG_FEC_MXC
151#define CONFIG_MII
152#define IMX_FEC_BASE ENET_BASE_ADDR
153#define CONFIG_FEC_XCV_TYPE RGMII
154#define CONFIG_FEC_MXC_PHYADDR 0
155#define CONFIG_PHYLIB
156#define CONFIG_ARP_TIMEOUT 200UL
157
158
159#define CONFIG_USB_EHCI
160#define CONFIG_USB_EHCI_MX6
161#define CONFIG_USB_HOST_ETHER
162#define CONFIG_USB_ETHER_ASIX
163#define CONFIG_USB_ETHER_SMSC95XX
164#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
165#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
166#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
167#define CONFIG_MXC_USB_FLAGS 0
168#define CONFIG_USBD_HS
169#define CONFIG_USB_ETHER
170#define CONFIG_USB_ETH_CDC
171#define CONFIG_NETCONSOLE
172#define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP
173
174
175#define CONFIG_USB_FUNCTION_MASS_STORAGE
176
177
178#define CONFIG_VIDEO_IPUV3
179#define CONFIG_VIDEO_LOGO
180#define CONFIG_IPUV3_CLK 260000000
181#define CONFIG_CMD_HDMIDETECT
182#define CONFIG_IMX_HDMI
183#define CONFIG_IMX_VIDEO_SKIP
184#define CONFIG_VIDEO_BMP_LOGO
185#define CONFIG_SPLASH_SCREEN_ALIGN
186#define CONFIG_HIDE_LOGO_VERSION
187
188
189#define CONFIG_HWCONFIG
190#define CONFIG_PREBOOT
191
192
193#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
194
195
196#define CONFIG_SYS_MEMTEST_START 0x10000000
197#define CONFIG_SYS_MEMTEST_END 0x10010000
198#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000
199
200
201#define CONFIG_NR_DRAM_BANKS 1
202#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
203#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
204#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
205#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
206
207#define CONFIG_SYS_INIT_SP_OFFSET \
208 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
209#define CONFIG_SYS_INIT_SP_ADDR \
210 (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
211
212
213
214
215#define CONFIG_LZO
216#define CONFIG_CMD_MTDPARTS
217#define CONFIG_MTD_DEVICE
218#define CONFIG_MTD_PARTITIONS
219#ifdef CONFIG_SPI_FLASH
220#define MTDIDS_DEFAULT "nor0=nor"
221#define MTDPARTS_DEFAULT \
222 "mtdparts=nor:512k(uboot),64k(env),2m(kernel),-(rootfs)"
223#else
224#define MTDIDS_DEFAULT "nand0=nand"
225#define MTDPARTS_DEFAULT "mtdparts=nand:16m(uboot),1m(env),-(rootfs)"
226#endif
227
228
229#ifdef CONFIG_SPI_FLASH
230#define CONFIG_ENV_IS_IN_SPI_FLASH
231#else
232#define CONFIG_ENV_IS_IN_NAND
233#endif
234#if defined(CONFIG_ENV_IS_IN_MMC)
235 #define CONFIG_SYS_MMC_ENV_DEV 0
236 #define CONFIG_ENV_OFFSET (709 * SZ_1K)
237 #define CONFIG_ENV_SIZE (128 * SZ_1K)
238 #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + (128 * SZ_1K))
239#elif defined(CONFIG_ENV_IS_IN_NAND)
240 #define CONFIG_ENV_OFFSET (16 * SZ_1M)
241 #define CONFIG_ENV_SECT_SIZE (128 * SZ_1K)
242 #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
243 #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + (512 * SZ_1K))
244 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
245#elif defined(CONFIG_ENV_IS_IN_SPI_FLASH)
246 #define CONFIG_ENV_OFFSET (512 * SZ_1K)
247 #define CONFIG_ENV_SECT_SIZE (64 * SZ_1K)
248 #define CONFIG_ENV_SIZE (8 * SZ_1K)
249 #define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
250 #define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
251 #define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
252 #define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
253#endif
254
255
256#define CONFIG_IPADDR 192.168.1.1
257#define CONFIG_SERVERIP 192.168.1.146
258
259#define CONFIG_EXTRA_ENV_SETTINGS_COMMON \
260 "pcidisable=1\0" \
261 "splashpos=m,m\0" \
262 "usb_pgood_delay=2000\0" \
263 "console=ttymxc1\0" \
264 "bootdevs=usb mmc sata flash\0" \
265 "hwconfig=_UNKNOWN_\0" \
266 "video=\0" \
267 \
268 "mtdparts=" MTDPARTS_DEFAULT "\0" \
269 "mtdids=" MTDIDS_DEFAULT "\0" \
270 "disk=0\0" \
271 "part=1\0" \
272 \
273 "fdt_high=0xffffffff\0" \
274 "fdt_addr=0x18000000\0" \
275 "initrd_high=0xffffffff\0" \
276 "fixfdt=" \
277 "fdt addr ${fdt_addr}\0" \
278 "bootdir=boot\0" \
279 "loadfdt=" \
280 "if ${fsload} ${fdt_addr} ${bootdir}/${fdt_file}; then " \
281 "echo Loaded DTB from ${bootdir}/${fdt_file}; " \
282 "run fixfdt; " \
283 "elif ${fsload} ${fdt_addr} ${bootdir}/${fdt_file1}; then " \
284 "echo Loaded DTB from ${bootdir}/${fdt_file1}; " \
285 "run fixfdt; " \
286 "elif ${fsload} ${fdt_addr} ${bootdir}/${fdt_file2}; then " \
287 "echo Loaded DTB from ${bootdir}/${fdt_file2}; " \
288 "run fixfdt; " \
289 "fi\0" \
290 \
291 "fs=ext4\0" \
292 "script=6x_bootscript-ventana\0" \
293 "loadscript=" \
294 "if ${fsload} ${loadaddr} ${bootdir}/${script}; then " \
295 "source ${loadaddr}; " \
296 "fi\0" \
297 \
298 "uimage=uImage\0" \
299 "mmc_root=/dev/mmcblk0p1 rootfstype=${fs} rootwait rw\0" \
300 "mmc_boot=" \
301 "setenv fsload \"${fs}load mmc ${disk}:${part}\"; " \
302 "mmc dev ${disk} && mmc rescan && " \
303 "setenv dtype mmc; run loadscript; " \
304 "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \
305 "setenv bootargs console=${console},${baudrate} " \
306 "root=/dev/mmcblk0p1 rootfstype=${fs} " \
307 "rootwait rw ${video} ${extra}; " \
308 "if run loadfdt; then " \
309 "bootm ${loadaddr} - ${fdt_addr}; " \
310 "else " \
311 "bootm; " \
312 "fi; " \
313 "fi\0" \
314 \
315 "sata_boot=" \
316 "setenv fsload \"${fs}load sata ${disk}:${part}\"; " \
317 "sata init && " \
318 "setenv dtype sata; run loadscript; " \
319 "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \
320 "setenv bootargs console=${console},${baudrate} " \
321 "root=/dev/sda1 rootfstype=${fs} " \
322 "rootwait rw ${video} ${extra}; " \
323 "if run loadfdt; then " \
324 "bootm ${loadaddr} - ${fdt_addr}; " \
325 "else " \
326 "bootm; " \
327 "fi; " \
328 "fi\0" \
329 "usb_boot=" \
330 "setenv fsload \"${fs}load usb ${disk}:${part}\"; " \
331 "usb start && usb dev ${disk} && " \
332 "setenv dtype usb; run loadscript; " \
333 "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \
334 "setenv bootargs console=${console},${baudrate} " \
335 "root=/dev/sda1 rootfstype=${fs} " \
336 "rootwait rw ${video} ${extra}; " \
337 "if run loadfdt; then " \
338 "bootm ${loadaddr} - ${fdt_addr}; " \
339 "else " \
340 "bootm; " \
341 "fi; " \
342 "fi\0"
343
344#ifdef CONFIG_SPI_FLASH
345 #define CONFIG_EXTRA_ENV_SETTINGS \
346 CONFIG_EXTRA_ENV_SETTINGS_COMMON \
347 "image_os=ventana/openwrt-imx6-imx6q-gw5400-a-squashfs.bin\0" \
348 "image_uboot=ventana/u-boot_spi.imx\0" \
349 \
350 "spi_koffset=0x90000\0" \
351 "spi_klen=0x200000\0" \
352 \
353 "spi_updateuboot=echo Updating uboot from " \
354 "${serverip}:${image_uboot}...; " \
355 "tftpboot ${loadaddr} ${image_uboot} && " \
356 "sf probe && sf erase 0 80000 && " \
357 "sf write ${loadaddr} 400 ${filesize}\0" \
358 "spi_update=echo Updating OS from ${serverip}:${image_os} " \
359 "to ${spi_koffset} ...; " \
360 "tftp ${loadaddr} ${image_os} && " \
361 "sf probe && " \
362 "sf update ${loadaddr} ${spi_koffset} ${filesize}\0" \
363 \
364 "flash_boot=" \
365 "if sf probe && " \
366 "sf read ${loadaddr} ${spi_koffset} ${spi_klen}; then " \
367 "setenv bootargs console=${console},${baudrate} " \
368 "root=/dev/mtdblock3 " \
369 "rootfstype=squashfs,jffs2 " \
370 "${video} ${extra}; " \
371 "bootm; " \
372 "fi\0"
373#else
374 #define CONFIG_EXTRA_ENV_SETTINGS \
375 CONFIG_EXTRA_ENV_SETTINGS_COMMON \
376 \
377 "image_rootfs=openwrt-imx6-ventana-rootfs.ubi\0" \
378 "nand_update=echo Updating NAND from ${serverip}:${image_rootfs}...; " \
379 "tftp ${loadaddr} ${image_rootfs} && " \
380 "nand erase.part rootfs && " \
381 "nand write ${loadaddr} rootfs ${filesize}\0" \
382 \
383 "flash_boot=" \
384 "setenv fsload 'ubifsload'; " \
385 "ubi part rootfs; " \
386 "if ubi check boot; then " \
387 "ubifsmount ubi0:boot; " \
388 "setenv root ubi0:rootfs ubi.mtd=2 " \
389 "rootfstype=squashfs,ubifs; " \
390 "setenv bootdir; " \
391 "elif ubi check rootfs; then " \
392 "ubifsmount ubi0:rootfs; " \
393 "setenv root ubi0:rootfs ubi.mtd=2 " \
394 "rootfstype=ubifs; " \
395 "fi; " \
396 "setenv dtype nand; run loadscript; " \
397 "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \
398 "setenv bootargs console=${console},${baudrate} " \
399 "root=${root} ${video} ${extra}; " \
400 "if run loadfdt; then " \
401 "ubifsumount; " \
402 "bootm ${loadaddr} - ${fdt_addr}; " \
403 "else " \
404 "ubifsumount; bootm; " \
405 "fi; " \
406 "fi\0"
407#endif
408
409#define CONFIG_BOOTCOMMAND \
410 "for btype in ${bootdevs}; do " \
411 "echo; echo Attempting ${btype} boot...; " \
412 "if run ${btype}_boot; then; fi; " \
413 "done"
414
415#endif
416
