LXR uboot/board/tqc/tqm834x/tqm834x.c

   1/*
   2 * (C) Copyright 2005
   3 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
   4 *
   5 * SPDX-License-Identifier:     GPL-2.0+
   6 */
   7
   8#include <common.h>
   9#include <ioports.h>
  10#include <mpc83xx.h>
  11#include <asm/mpc8349_pci.h>
  12#include <i2c.h>
  13#include <miiphy.h>
  14#include <asm/mmu.h>
  15#include <pci.h>
  16#include <flash.h>
  17#include <mtd/cfi_flash.h>
  18
  19DECLARE_GLOBAL_DATA_PTR;
  20
  21#define IOSYNC                  asm("eieio")
  22#define ISYNC                   asm("isync")
  23#define SYNC                    asm("sync")
  24#define FPW                     FLASH_PORT_WIDTH
  25#define FPWV                    FLASH_PORT_WIDTHV
  26
  27#define DDR_MAX_SIZE_PER_CS     0x20000000
  28
  29#if defined(DDR_CASLAT_20)
  30#define TIMING_CASLAT           TIMING_CFG1_CASLAT_20
  31#define MODE_CASLAT             DDR_MODE_CASLAT_20
  32#else
  33#define TIMING_CASLAT           TIMING_CFG1_CASLAT_25
  34#define MODE_CASLAT             DDR_MODE_CASLAT_25
  35#endif
  36
  37#define INITIAL_CS_CONFIG       (CSCONFIG_EN | CSCONFIG_ROW_BIT_12 | \
  38                                CSCONFIG_COL_BIT_9)
  39
  40/* External definitions */
  41ulong flash_get_size (ulong base, int banknum);
  42
  43/* Local functions */
  44static int detect_num_flash_banks(void);
  45static long int get_ddr_bank_size(short cs, long *base);
  46static void set_cs_bounds(short cs, ulong base, ulong size);
  47static void set_cs_config(short cs, long config);
  48static void set_ddr_config(void);
  49
  50/* Local variable */
  51static volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
  52
  53/**************************************************************************
  54 * Board initialzation after relocation to RAM. Used to detect the number
  55 * of Flash banks on TQM834x.
  56 */
  57int board_early_init_r (void) {
  58        /* sanity check, IMMARBAR should be mirrored at offset zero of IMMR */
  59        if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32)im)
  60                return 0;
  61
  62        /* detect the number of Flash banks */
  63        return detect_num_flash_banks();
  64}
  65
  66/**************************************************************************
  67 * DRAM initalization and size detection
  68 */
  69phys_size_t initdram (int board_type)
  70{
  71        long bank_size;
  72        long size;
  73        int cs;
  74
  75        /* during size detection, set up the max DDRLAW size */
  76        im->sysconf.ddrlaw[0].bar = CONFIG_SYS_DDR_BASE;
  77        im->sysconf.ddrlaw[0].ar = (LAWAR_EN | LAWAR_SIZE_2G);
  78
  79        /* set CS bounds to maximum size */
  80        for(cs = 0; cs < 4; ++cs) {
  81                set_cs_bounds(cs,
  82                        CONFIG_SYS_DDR_BASE + (cs * DDR_MAX_SIZE_PER_CS),
  83                        DDR_MAX_SIZE_PER_CS);
  84
  85                set_cs_config(cs, INITIAL_CS_CONFIG);
  86        }
  87
  88        /* configure ddr controller */
  89        set_ddr_config();
  90
  91        udelay(200);
  92
  93        /* enable DDR controller */
  94        im->ddr.sdram_cfg = (SDRAM_CFG_MEM_EN |
  95                SDRAM_CFG_SREN |
  96                SDRAM_CFG_SDRAM_TYPE_DDR1);
  97        SYNC;
  98
  99        /* size detection */
 100        debug("\n");
 101        size = 0;
 102        for(cs = 0; cs < 4; ++cs) {
 103                debug("\nDetecting Bank%d\n", cs);
 104
 105                bank_size = get_ddr_bank_size(cs,
 106                        (long *)(CONFIG_SYS_DDR_BASE + size));
 107                size += bank_size;
 108
 109                debug("DDR Bank%d size: %ld MiB\n\n", cs, bank_size >> 20);
 110
 111                /* exit if less than one bank */
 112                if(size < DDR_MAX_SIZE_PER_CS) break;
 113        }
 114
 115        return size;
 116}
 117
 118/**************************************************************************
 119 * checkboard()
 120 */
 121int checkboard (void)
 122{
 123        puts("Board: TQM834x\n");
 124
 125#ifdef CONFIG_PCI
 126        volatile immap_t * immr;
 127        u32 w, f;
 128
 129        immr = (immap_t *)CONFIG_SYS_IMMR;
 130        if (!(immr->reset.rcwh & HRCWH_PCI_HOST)) {
 131                printf("PCI:   NOT in host mode..?!\n");
 132                return 0;
 133        }
 134
 135        /* get bus width */
 136        w = 32;
 137        if (immr->reset.rcwh & HRCWH_64_BIT_PCI)
 138                w = 64;
 139
 140        /* get clock */
 141        f = gd->pci_clk;
 142
 143        printf("PCI1:  %d bit, %d MHz\n", w, f / 1000000);
 144#else
 145        printf("PCI:   disabled\n");
 146#endif
 147        return 0;
 148}
 149
 150
 151/**************************************************************************
 152 *
 153 * Local functions
 154 *
 155 *************************************************************************/
 156
 157/**************************************************************************
 158 * Detect the number of flash banks (1 or 2). Store it in
 159 * a global variable tqm834x_num_flash_banks.
 160 * Bank detection code based on the Monitor code.
 161 */
 162static int detect_num_flash_banks(void)
 163{
 164        typedef unsigned long FLASH_PORT_WIDTH;
 165        typedef volatile unsigned long FLASH_PORT_WIDTHV;
 166        FPWV *bank1_base;
 167        FPWV *bank2_base;
 168        FPW bank1_read;
 169        FPW bank2_read;
 170        ulong bank1_size;
 171        ulong bank2_size;
 172        ulong total_size;
 173
 174        cfi_flash_num_flash_banks = 2;  /* assume two banks */
 175
 176        /* Get bank 1 and 2 information */
 177        bank1_size = flash_get_size(CONFIG_SYS_FLASH_BASE, 0);
 178        debug("Bank1 size: %lu\n", bank1_size);
 179        bank2_size = flash_get_size(CONFIG_SYS_FLASH_BASE + bank1_size, 1);
 180        debug("Bank2 size: %lu\n", bank2_size);
 181        total_size = bank1_size + bank2_size;
 182
 183        if (bank2_size > 0) {
 184                /* Seems like we've got bank 2, but maybe it's mirrored 1 */
 185
 186                /* Set the base addresses */
 187                bank1_base = (FPWV *) (CONFIG_SYS_FLASH_BASE);
 188                bank2_base = (FPWV *) (CONFIG_SYS_FLASH_BASE + bank1_size);
 189
 190                /* Put bank 2 into CFI command mode and read */
 191                bank2_base[0x55] = 0x00980098;
 192                IOSYNC;
 193                ISYNC;
 194                bank2_read = bank2_base[0x10];
 195
 196                /* Read from bank 1 (it's in read mode) */
 197                bank1_read = bank1_base[0x10];
 198
 199                /* Reset Flash */
 200                bank1_base[0] = 0x00F000F0;
 201                bank2_base[0] = 0x00F000F0;
 202
 203                if (bank2_read == bank1_read) {
 204                        /*
 205                         * Looks like just one bank, but not sure yet. Let's
 206                         * read from bank 2 in autosoelect mode.
 207                         */
 208                        bank2_base[0x0555] = 0x00AA00AA;
 209                        bank2_base[0x02AA] = 0x00550055;
 210                        bank2_base[0x0555] = 0x00900090;
 211                        IOSYNC;
 212                        ISYNC;
 213                        bank2_read = bank2_base[0x10];
 214
 215                        /* Read from bank 1 (it's in read mode) */
 216                        bank1_read = bank1_base[0x10];
 217
 218                        /* Reset Flash */
 219                        bank1_base[0] = 0x00F000F0;
 220                        bank2_base[0] = 0x00F000F0;
 221
 222                        if (bank2_read == bank1_read) {
 223                                /*
 224                                 * In both CFI command and autoselect modes,
 225                                 * we got the some data reading from Flash.
 226                                 * There is only one mirrored bank.
 227                                 */
 228                                cfi_flash_num_flash_banks = 1;
 229                                total_size = bank1_size;
 230                        }
 231                }
 232        }
 233
 234        debug("Number of flash banks detected: %d\n", cfi_flash_num_flash_banks);
 235
 236        /* set OR0 and BR0 */
 237        set_lbc_or(0, CONFIG_SYS_OR_TIMING_FLASH |
 238                   (-(total_size) & OR_GPCM_AM));
 239        set_lbc_br(0, (CONFIG_SYS_FLASH_BASE & BR_BA) |
 240                   (BR_MS_GPCM | BR_PS_32 | BR_V));
 241
 242        return (0);
 243}
 244
 245/*************************************************************************
 246 * Detect the size of a ddr bank. Sets CS bounds and CS config accordingly.
 247 */
 248static long int get_ddr_bank_size(short cs, long *base)
 249{
 250        /* This array lists all valid DDR SDRAM configurations, with
 251         * Bank sizes in bytes. (Refer to Table 9-27 in the MPC8349E RM).
 252         * The last entry has to to have size equal 0 and is igonred during
 253         * autodection. Bank sizes must be in increasing order of size
 254         */
 255        struct {
 256                long row;
 257                long col;
 258                long size;
 259        } conf[] = {
 260                {CSCONFIG_ROW_BIT_12,   CSCONFIG_COL_BIT_8,     32 << 20},
 261                {CSCONFIG_ROW_BIT_12,   CSCONFIG_COL_BIT_9,     64 << 20},
 262                {CSCONFIG_ROW_BIT_12,   CSCONFIG_COL_BIT_10,    128 << 20},
 263                {CSCONFIG_ROW_BIT_13,   CSCONFIG_COL_BIT_9,     128 << 20},
 264                {CSCONFIG_ROW_BIT_13,   CSCONFIG_COL_BIT_10,    256 << 20},
 265                {CSCONFIG_ROW_BIT_13,   CSCONFIG_COL_BIT_11,    512 << 20},
 266                {CSCONFIG_ROW_BIT_14,   CSCONFIG_COL_BIT_10,    512 << 20},
 267                {CSCONFIG_ROW_BIT_14,   CSCONFIG_COL_BIT_11,    1024 << 20},
 268                {0,                     0,                      0}
 269        };
 270
 271        int i;
 272        int detected;
 273        long size;
 274
 275        detected = -1;
 276        for(i = 0; conf[i].size != 0; ++i) {
 277
 278                /* set sdram bank configuration */
 279                set_cs_config(cs, CSCONFIG_EN | conf[i].col | conf[i].row);
 280
 281                debug("Getting RAM size...\n");
 282                size = get_ram_size(base, DDR_MAX_SIZE_PER_CS);
 283
 284                if((size == conf[i].size) && (i == detected + 1))
 285                        detected = i;
 286
 287                debug("Trying %ld x %ld (%ld MiB) at addr %p, detected: %ld MiB\n",
 288                        conf[i].row,
 289                        conf[i].col,
 290                        conf[i].size >> 20,
 291                        base,
 292                        size >> 20);
 293        }
 294
 295        if(detected == -1){
 296                /* disable empty cs */
 297                debug("\nNo valid configurations for CS%d, disabling...\n", cs);
 298                set_cs_config(cs, 0);
 299                return 0;
 300        }
 301
 302        debug("\nDetected configuration %ld x %ld (%ld MiB) at addr %p\n",
 303                        conf[detected].row, conf[detected].col, conf[detected].size >> 20, base);
 304
 305        /* configure cs ro detected params */
 306        set_cs_config(cs, CSCONFIG_EN | conf[detected].row |
 307                        conf[detected].col);
 308
 309        set_cs_bounds(cs, (long)base, conf[detected].size);
 310
 311        return(conf[detected].size);
 312}
 313
 314/**************************************************************************
 315 * Sets DDR bank CS bounds.
 316 */
 317static void set_cs_bounds(short cs, ulong base, ulong size)
 318{
 319        debug("Setting bounds %08lx, %08lx for cs %d\n", base, size, cs);
 320        if(size == 0){
 321                im->ddr.csbnds[cs].csbnds = 0x00000000;
 322        } else {
 323                im->ddr.csbnds[cs].csbnds =
 324                        ((base >> CSBNDS_SA_SHIFT) & CSBNDS_SA) |
 325                        (((base + size - 1) >> CSBNDS_EA_SHIFT) &
 326                                CSBNDS_EA);
 327        }
 328        SYNC;
 329}
 330
 331/**************************************************************************
 332 * Sets DDR banks CS configuration.
 333 * config == 0x00000000 disables the CS.
 334 */
 335static void set_cs_config(short cs, long config)
 336{
 337        debug("Setting config %08lx for cs %d\n", config, cs);
 338        im->ddr.cs_config[cs] = config;
 339        SYNC;
 340}
 341
 342/**************************************************************************
 343 * Sets DDR clocks, timings and configuration.
 344 */
 345static void set_ddr_config(void) {
 346        /* clock control */
 347        im->ddr.sdram_clk_cntl = DDR_SDRAM_CLK_CNTL_SS_EN |
 348                DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05;
 349        SYNC;
 350
 351        /* timing configuration */
 352        im->ddr.timing_cfg_1 =
 353                (4 << TIMING_CFG1_PRETOACT_SHIFT) |
 354                (7 << TIMING_CFG1_ACTTOPRE_SHIFT) |
 355                (4 << TIMING_CFG1_ACTTORW_SHIFT)  |
 356                (5 << TIMING_CFG1_REFREC_SHIFT)   |
 357                (3 << TIMING_CFG1_WRREC_SHIFT)    |
 358                (3 << TIMING_CFG1_ACTTOACT_SHIFT) |
 359                (1 << TIMING_CFG1_WRTORD_SHIFT)   |
 360                (TIMING_CFG1_CASLAT & TIMING_CASLAT);
 361
 362        im->ddr.timing_cfg_2 =
 363                TIMING_CFG2_CPO_DEF |
 364                (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT);
 365        SYNC;
 366
 367        /* don't enable DDR controller yet */
 368        im->ddr.sdram_cfg =
 369                SDRAM_CFG_SREN |
 370                SDRAM_CFG_SDRAM_TYPE_DDR1;
 371        SYNC;
 372
 373        /* Set SDRAM mode */
 374        im->ddr.sdram_mode =
 375                ((DDR_MODE_EXT_MODEREG | DDR_MODE_WEAK) <<
 376                        SDRAM_MODE_ESD_SHIFT) |
 377                ((DDR_MODE_MODEREG | DDR_MODE_BLEN_4) <<
 378                        SDRAM_MODE_SD_SHIFT) |
 379                ((DDR_MODE_CASLAT << SDRAM_MODE_SD_SHIFT) &
 380                        MODE_CASLAT);
 381        SYNC;
 382
 383        /* Set fast SDRAM refresh rate */
 384        im->ddr.sdram_interval =
 385                (DDR_REFINT_166MHZ_7US << SDRAM_INTERVAL_REFINT_SHIFT) |
 386                (DDR_BSTOPRE << SDRAM_INTERVAL_BSTOPRE_SHIFT);
 387        SYNC;
 388
 389        /* Workaround for DDR6 Erratum
 390         * see MPC8349E Device Errata Rev.8, 2/2006
 391         * This workaround influences the MPC internal "input enables"
 392         * dependent on CAS latency and MPC revision. According to errata
 393         * sheet the internal reserved registers for this workaround are
 394         * not available from revision 2.0 and up.
 395         */
 396
 397        /* Get REVID from register SPRIDR. Skip workaround if rev >= 2.0
 398         * (0x200)
 399         */
 400        if ((im->sysconf.spridr & SPRIDR_REVID) < 0x200) {
 401
 402                /* There is a internal reserved register at IMMRBAR+0x2F00
 403                 * which has to be written with a certain value defined by
 404                 * errata sheet.
 405                 */
 406                u32 *reserved_p = (u32 *)((u8 *)im + 0x2f00);
 407
 408#if defined(DDR_CASLAT_20)
 409                *reserved_p = 0x201c0000;
 410#else
 411                *reserved_p = 0x202c0000;
 412#endif
 413        }
 414}
 415
 416#ifdef CONFIG_OF_BOARD_SETUP
 417int ft_board_setup(void *blob, bd_t *bd)
 418{
 419        ft_cpu_setup(blob, bd);
 420
 421#ifdef CONFIG_PCI
 422        ft_pci_setup(blob, bd);
 423#endif  /* CONFIG_PCI */
 424
 425        return 0;
 426}
 427#endif  /* CONFIG_OF_BOARD_SETUP */
 428