1
2
3
4
5
6
7#ifndef __CONFIG_H
8#define __CONFIG_H
9
10
11#define CONFIG_SPL_BOARD_INIT
12
13#define CONFIG_SYS_NAND_U_BOOT_OFFS (14 * SZ_1M)
14
15
16#define CONFIG_CMD_SPL
17#define CONFIG_SYS_SPL_ARGS_ADDR 0x18000000
18#define CONFIG_CMD_SPL_WRITE_SIZE (128 * SZ_1K)
19
20
21#define CONFIG_CMD_SPL_NAND_OFS (17 * SZ_1M)
22#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS (18 * SZ_1M)
23
24
25#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x800
26#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS (CONFIG_CMD_SPL_WRITE_SIZE / 512)
27#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x1000
28
29#include "imx6_spl.h"
30#include "mx6_common.h"
31#define CONFIG_DISPLAY_BOARDINFO_LATE
32
33#define CONFIG_MACH_TYPE 4520
34
35
36#define CONFIG_SERIAL_TAG
37
38
39#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)
40
41
42#define CONFIG_MISC_INIT_R
43
44
45#ifndef CONFIG_SPL_BUILD
46#define CONFIG_DM_GPIO
47#define CONFIG_DM_THERMAL
48#endif
49
50
51#define CONFIG_IMX_THERMAL
52
53
54#define CONFIG_MXC_UART
55#define CONFIG_MXC_UART_BASE UART2_BASE
56
57#ifdef CONFIG_SPI_FLASH
58
59
60#ifdef CONFIG_CMD_SF
61 #define CONFIG_MXC_SPI
62 #define CONFIG_SPI_FLASH_MTD
63 #define CONFIG_SPI_FLASH_BAR
64 #define CONFIG_SF_DEFAULT_BUS 0
65 #define CONFIG_SF_DEFAULT_CS 0
66
67 #define CONFIG_SF_DEFAULT_SPEED 30000000
68 #define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
69#endif
70
71#else
72
73#define CONFIG_CMD_NAND
74#define CONFIG_CMD_NAND_TRIMFFS
75#ifdef CONFIG_CMD_NAND
76 #define CONFIG_NAND_MXS
77 #define CONFIG_SYS_MAX_NAND_DEVICE 1
78 #define CONFIG_SYS_NAND_BASE 0x40000000
79 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
80 #define CONFIG_SYS_NAND_ONFI_DETECTION
81
82
83 #define CONFIG_APBH_DMA
84 #define CONFIG_APBH_DMA_BURST
85 #define CONFIG_APBH_DMA_BURST8
86#endif
87
88#endif
89
90
91#define CONFIG_SYS_I2C
92#define CONFIG_SYS_I2C_MXC
93#define CONFIG_SYS_I2C_MXC_I2C1
94#define CONFIG_SYS_I2C_MXC_I2C2
95#define CONFIG_SYS_I2C_MXC_I2C3
96#define CONFIG_SYS_I2C_SPEED 100000
97#define CONFIG_I2C_GSC 0
98#define CONFIG_I2C_PMIC 1
99#define CONFIG_I2C_EDID
100
101
102#define CONFIG_SYS_FSL_ESDHC_ADDR 0
103#define CONFIG_SYS_FSL_USDHC_NUM 1
104
105
106#define CONFIG_CMD_UBIFS
107
108
109
110
111#define CONFIG_CMD_SATA
112#ifdef CONFIG_CMD_SATA
113 #define CONFIG_DWC_AHSATA
114 #define CONFIG_SYS_SATA_MAX_DEVICE 1
115 #define CONFIG_DWC_AHSATA_PORT_ID 0
116 #define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
117 #define CONFIG_LBA48
118 #define CONFIG_LIBATA
119#endif
120
121
122
123
124#define CONFIG_CMD_PCI
125#ifdef CONFIG_CMD_PCI
126#define CONFIG_PCI_SCAN_SHOW
127#define CONFIG_PCI_FIXUP_DEV
128#define CONFIG_PCIE_IMX
129#endif
130
131
132
133
134#define CONFIG_POWER
135#define CONFIG_POWER_I2C
136#define CONFIG_POWER_PFUZE100
137#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
138#define CONFIG_POWER_LTC3676
139#define CONFIG_POWER_LTC3676_I2C_ADDR 0x3c
140
141
142#define CONFIG_CMD_BMODE
143#define CONFIG_CMD_HDMIDETECT
144#define CONFIG_CMD_GSC
145#define CONFIG_CMD_EECONFIG
146#define CONFIG_RBTREE
147
148
149#define CONFIG_FEC_MXC
150#define CONFIG_MII
151#define IMX_FEC_BASE ENET_BASE_ADDR
152#define CONFIG_FEC_XCV_TYPE RGMII
153#define CONFIG_FEC_MXC_PHYADDR 0
154#define CONFIG_PHYLIB
155#define CONFIG_ARP_TIMEOUT 200UL
156
157
158#define CONFIG_USB_EHCI
159#define CONFIG_USB_EHCI_MX6
160#define CONFIG_USB_HOST_ETHER
161#define CONFIG_USB_ETHER_ASIX
162#define CONFIG_USB_ETHER_SMSC95XX
163#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
164#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
165#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
166#define CONFIG_MXC_USB_FLAGS 0
167#define CONFIG_USBD_HS
168#define CONFIG_USB_ETHER
169#define CONFIG_USB_ETH_CDC
170#define CONFIG_NETCONSOLE
171#define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP
172
173
174#define CONFIG_USB_FUNCTION_MASS_STORAGE
175
176
177#define CONFIG_VIDEO_IPUV3
178#define CONFIG_VIDEO_LOGO
179#define CONFIG_IPUV3_CLK 260000000
180#define CONFIG_CMD_HDMIDETECT
181#define CONFIG_IMX_HDMI
182#define CONFIG_IMX_VIDEO_SKIP
183#define CONFIG_VIDEO_BMP_LOGO
184#define CONFIG_SPLASH_SCREEN_ALIGN
185#define CONFIG_HIDE_LOGO_VERSION
186
187
188#define CONFIG_HWCONFIG
189#define CONFIG_PREBOOT
190
191
192#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
193
194
195#define CONFIG_SYS_MEMTEST_START 0x10000000
196#define CONFIG_SYS_MEMTEST_END 0x10010000
197#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000
198
199
200#define CONFIG_NR_DRAM_BANKS 1
201#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
202#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
203#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
204#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
205
206#define CONFIG_SYS_INIT_SP_OFFSET \
207 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
208#define CONFIG_SYS_INIT_SP_ADDR \
209 (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
210
211
212
213
214#define CONFIG_LZO
215#define CONFIG_CMD_MTDPARTS
216#define CONFIG_MTD_DEVICE
217#define CONFIG_MTD_PARTITIONS
218#ifdef CONFIG_SPI_FLASH
219#define MTDIDS_DEFAULT "nor0=nor"
220#define MTDPARTS_DEFAULT \
221 "mtdparts=nor:512k(uboot),64k(env),2m(kernel),-(rootfs)"
222#else
223#define MTDIDS_DEFAULT "nand0=nand"
224#define MTDPARTS_DEFAULT "mtdparts=nand:16m(uboot),1m(env),-(rootfs)"
225#endif
226
227
228#ifdef CONFIG_SPI_FLASH
229#define CONFIG_ENV_IS_IN_SPI_FLASH
230#else
231#define CONFIG_ENV_IS_IN_NAND
232#endif
233#if defined(CONFIG_ENV_IS_IN_MMC)
234 #define CONFIG_SYS_MMC_ENV_DEV 0
235 #define CONFIG_ENV_OFFSET (709 * SZ_1K)
236 #define CONFIG_ENV_SIZE (128 * SZ_1K)
237 #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + (128 * SZ_1K))
238#elif defined(CONFIG_ENV_IS_IN_NAND)
239 #define CONFIG_ENV_OFFSET (16 * SZ_1M)
240 #define CONFIG_ENV_SECT_SIZE (128 * SZ_1K)
241 #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
242 #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + (512 * SZ_1K))
243 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
244#elif defined(CONFIG_ENV_IS_IN_SPI_FLASH)
245 #define CONFIG_ENV_OFFSET (512 * SZ_1K)
246 #define CONFIG_ENV_SECT_SIZE (64 * SZ_1K)
247 #define CONFIG_ENV_SIZE (8 * SZ_1K)
248 #define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
249 #define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
250 #define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
251 #define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
252#endif
253
254
255#define CONFIG_IPADDR 192.168.1.1
256#define CONFIG_SERVERIP 192.168.1.146
257
258#define CONFIG_EXTRA_ENV_SETTINGS_COMMON \
259 "pcidisable=1\0" \
260 "splashpos=m,m\0" \
261 "usb_pgood_delay=2000\0" \
262 "console=ttymxc1\0" \
263 "bootdevs=usb mmc sata flash\0" \
264 "hwconfig=_UNKNOWN_\0" \
265 "video=\0" \
266 \
267 "mtdparts=" MTDPARTS_DEFAULT "\0" \
268 "mtdids=" MTDIDS_DEFAULT "\0" \
269 "disk=0\0" \
270 "part=1\0" \
271 \
272 "fdt_high=0xffffffff\0" \
273 "fdt_addr=0x18000000\0" \
274 "initrd_high=0xffffffff\0" \
275 "fixfdt=" \
276 "fdt addr ${fdt_addr}\0" \
277 "bootdir=boot\0" \
278 "loadfdt=" \
279 "if ${fsload} ${fdt_addr} ${bootdir}/${fdt_file}; then " \
280 "echo Loaded DTB from ${bootdir}/${fdt_file}; " \
281 "run fixfdt; " \
282 "elif ${fsload} ${fdt_addr} ${bootdir}/${fdt_file1}; then " \
283 "echo Loaded DTB from ${bootdir}/${fdt_file1}; " \
284 "run fixfdt; " \
285 "elif ${fsload} ${fdt_addr} ${bootdir}/${fdt_file2}; then " \
286 "echo Loaded DTB from ${bootdir}/${fdt_file2}; " \
287 "run fixfdt; " \
288 "fi\0" \
289 \
290 "fs=ext4\0" \
291 "script=6x_bootscript-ventana\0" \
292 "loadscript=" \
293 "if ${fsload} ${loadaddr} ${bootdir}/${script}; then " \
294 "source ${loadaddr}; " \
295 "fi\0" \
296 \
297 "uimage=uImage\0" \
298 "mmc_root=/dev/mmcblk0p1 rootfstype=${fs} rootwait rw\0" \
299 "mmc_boot=" \
300 "setenv fsload \"${fs}load mmc ${disk}:${part}\"; " \
301 "mmc dev ${disk} && mmc rescan && " \
302 "setenv dtype mmc; run loadscript; " \
303 "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \
304 "setenv bootargs console=${console},${baudrate} " \
305 "root=/dev/mmcblk0p1 rootfstype=${fs} " \
306 "rootwait rw ${video} ${extra}; " \
307 "if run loadfdt; then " \
308 "bootm ${loadaddr} - ${fdt_addr}; " \
309 "else " \
310 "bootm; " \
311 "fi; " \
312 "fi\0" \
313 \
314 "sata_boot=" \
315 "setenv fsload \"${fs}load sata ${disk}:${part}\"; " \
316 "sata init && " \
317 "setenv dtype sata; run loadscript; " \
318 "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \
319 "setenv bootargs console=${console},${baudrate} " \
320 "root=/dev/sda1 rootfstype=${fs} " \
321 "rootwait rw ${video} ${extra}; " \
322 "if run loadfdt; then " \
323 "bootm ${loadaddr} - ${fdt_addr}; " \
324 "else " \
325 "bootm; " \
326 "fi; " \
327 "fi\0" \
328 "usb_boot=" \
329 "setenv fsload \"${fs}load usb ${disk}:${part}\"; " \
330 "usb start && usb dev ${disk} && " \
331 "setenv dtype usb; run loadscript; " \
332 "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \
333 "setenv bootargs console=${console},${baudrate} " \
334 "root=/dev/sda1 rootfstype=${fs} " \
335 "rootwait rw ${video} ${extra}; " \
336 "if run loadfdt; then " \
337 "bootm ${loadaddr} - ${fdt_addr}; " \
338 "else " \
339 "bootm; " \
340 "fi; " \
341 "fi\0"
342
343#ifdef CONFIG_SPI_FLASH
344 #define CONFIG_EXTRA_ENV_SETTINGS \
345 CONFIG_EXTRA_ENV_SETTINGS_COMMON \
346 "image_os=ventana/openwrt-imx6-imx6q-gw5400-a-squashfs.bin\0" \
347 "image_uboot=ventana/u-boot_spi.imx\0" \
348 \
349 "spi_koffset=0x90000\0" \
350 "spi_klen=0x200000\0" \
351 \
352 "spi_updateuboot=echo Updating uboot from " \
353 "${serverip}:${image_uboot}...; " \
354 "tftpboot ${loadaddr} ${image_uboot} && " \
355 "sf probe && sf erase 0 80000 && " \
356 "sf write ${loadaddr} 400 ${filesize}\0" \
357 "spi_update=echo Updating OS from ${serverip}:${image_os} " \
358 "to ${spi_koffset} ...; " \
359 "tftp ${loadaddr} ${image_os} && " \
360 "sf probe && " \
361 "sf update ${loadaddr} ${spi_koffset} ${filesize}\0" \
362 \
363 "flash_boot=" \
364 "if sf probe && " \
365 "sf read ${loadaddr} ${spi_koffset} ${spi_klen}; then " \
366 "setenv bootargs console=${console},${baudrate} " \
367 "root=/dev/mtdblock3 " \
368 "rootfstype=squashfs,jffs2 " \
369 "${video} ${extra}; " \
370 "bootm; " \
371 "fi\0"
372#else
373 #define CONFIG_EXTRA_ENV_SETTINGS \
374 CONFIG_EXTRA_ENV_SETTINGS_COMMON \
375 \
376 "image_rootfs=openwrt-imx6-ventana-rootfs.ubi\0" \
377 "nand_update=echo Updating NAND from ${serverip}:${image_rootfs}...; " \
378 "tftp ${loadaddr} ${image_rootfs} && " \
379 "nand erase.part rootfs && " \
380 "nand write ${loadaddr} rootfs ${filesize}\0" \
381 \
382 "flash_boot=" \
383 "setenv fsload 'ubifsload'; " \
384 "ubi part rootfs; " \
385 "if ubi check boot; then " \
386 "ubifsmount ubi0:boot; " \
387 "setenv root ubi0:rootfs ubi.mtd=2 " \
388 "rootfstype=squashfs,ubifs; " \
389 "setenv bootdir; " \
390 "elif ubi check rootfs; then " \
391 "ubifsmount ubi0:rootfs; " \
392 "setenv root ubi0:rootfs ubi.mtd=2 " \
393 "rootfstype=ubifs; " \
394 "fi; " \
395 "setenv dtype nand; run loadscript; " \
396 "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \
397 "setenv bootargs console=${console},${baudrate} " \
398 "root=${root} ${video} ${extra}; " \
399 "if run loadfdt; then " \
400 "ubifsumount; " \
401 "bootm ${loadaddr} - ${fdt_addr}; " \
402 "else " \
403 "ubifsumount; bootm; " \
404 "fi; " \
405 "fi\0"
406#endif
407
408#define CONFIG_BOOTCOMMAND \
409 "for btype in ${bootdevs}; do " \
410 "echo; echo Attempting ${btype} boot...; " \
411 "if run ${btype}_boot; then; fi; " \
412 "done"
413
414#endif
415
