/*
 * Copyright 2011-2012 Freescale Semiconductor, Inc.
 *
 * SPDX-License-Identifier:     GPL-2.0+
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * B4860 QDS board configuration file
 */
#ifdef CONFIG_RAMBOOT_PBL
#define CONFIG_SYS_FSL_PBL_PBI  $(SRCTREE)/board/freescale/b4860qds/b4_pbi.cfg
#define CONFIG_SYS_FSL_PBL_RCW  $(SRCTREE)/board/freescale/b4860qds/b4_rcw.cfg
#ifndef CONFIG_NAND
#define CONFIG_RAMBOOT_TEXT_BASE        CONFIG_SYS_TEXT_BASE
#define CONFIG_RESET_VECTOR_ADDRESS     0xfffffffc
#else
#define CONFIG_SPL_FLUSH_IMAGE
#define CONFIG_SPL_TARGET               "u-boot-with-spl.bin"
#define CONFIG_SYS_TEXT_BASE            0x00201000
#define CONFIG_SPL_TEXT_BASE            0xFFFD8000
#define CONFIG_SPL_PAD_TO               0x40000
#define CONFIG_SPL_MAX_SIZE             0x28000
#define RESET_VECTOR_OFFSET             0x27FFC
#define BOOT_PAGE_OFFSET                0x27000
#define CONFIG_SYS_NAND_U_BOOT_SIZE     (768 << 10)
#define CONFIG_SYS_NAND_U_BOOT_DST      0x00200000
#define CONFIG_SYS_NAND_U_BOOT_START    0x00200000
#define CONFIG_SYS_NAND_U_BOOT_OFFS     (256 << 10)
#define CONFIG_SYS_LDSCRIPT     "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
#define CONFIG_SPL_NAND_BOOT
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SPL_SKIP_RELOCATE
#define CONFIG_SPL_COMMON_INIT_DDR
#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
#endif
#endif
#endif

#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
/* Set 1M boot space */
#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
                (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
#endif

/* High Level Configuration Options */
#define CONFIG_SYS_BOOK3E_HV            /* Category E.HV supported */
#define CONFIG_MP                       /* support multiple processors */

#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE    0xeff40000
#endif

#ifndef CONFIG_RESET_VECTOR_ADDRESS
#define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
#endif

#define CONFIG_SYS_FSL_CPC              /* Corenet Platform Cache */
#define CONFIG_SYS_NUM_CPC              CONFIG_SYS_NUM_DDR_CTLRS
#define CONFIG_PCIE1                    /* PCIE controller 1 */
#define CONFIG_FSL_PCI_INIT             /* Use common FSL init code */
#define CONFIG_SYS_PCI_64BIT            /* enable 64-bit PCI resources */

#ifndef CONFIG_ARCH_B4420
#define CONFIG_SYS_SRIO
#define CONFIG_SRIO1                    /* SRIO port 1 */
#define CONFIG_SRIO2                    /* SRIO port 2 */
#define CONFIG_SRIO_PCIE_BOOT_MASTER
#endif

/* I2C bus multiplexer */
#define I2C_MUX_PCA_ADDR                0x77

/* VSC Crossbar switches */
#define CONFIG_VSC_CROSSBAR
#define I2C_CH_DEFAULT                  0x8
#define I2C_CH_VSC3316                  0xc
#define I2C_CH_VSC3308                  0xd

#define VSC3316_TX_ADDRESS              0x70
#define VSC3316_RX_ADDRESS              0x71
#define VSC3308_TX_ADDRESS              0x02
#define VSC3308_RX_ADDRESS              0x03

/* IDT clock synthesizers */
#define CONFIG_IDT8T49N222A
#define I2C_CH_IDT                     0x9

#define IDT_SERDES1_ADDRESS            0x6E
#define IDT_SERDES2_ADDRESS            0x6C

/* Voltage monitor on channel 2*/
#define I2C_MUX_CH_VOL_MONITOR          0xa
#define I2C_VOL_MONITOR_ADDR            0x40
#define I2C_VOL_MONITOR_BUS_V_OFFSET    0x2
#define I2C_VOL_MONITOR_BUS_V_OVF       0x1
#define I2C_VOL_MONITOR_BUS_V_SHIFT     3

#define CONFIG_ZM7300
#define I2C_MUX_CH_DPM                  0xa
#define I2C_DPM_ADDR                    0x28

#define CONFIG_ENV_OVERWRITE

#ifndef CONFIG_MTD_NOR_FLASH
#if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL)
#define CONFIG_ENV_IS_NOWHERE
#endif
#else
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#endif

#if defined(CONFIG_SPIFLASH)
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SPI_BUS              0
#define CONFIG_ENV_SPI_CS               0
#define CONFIG_ENV_SPI_MAX_HZ           10000000
#define CONFIG_ENV_SPI_MODE             0
#define CONFIG_ENV_SIZE                 0x2000          /* 8KB */
#define CONFIG_ENV_OFFSET               0x100000        /* 1MB */
#define CONFIG_ENV_SECT_SIZE            0x10000
#elif defined(CONFIG_SDCARD)
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_SYS_MMC_ENV_DEV          0
#define CONFIG_ENV_SIZE                 0x2000
#define CONFIG_ENV_OFFSET               (512 * 1097)
#elif defined(CONFIG_NAND)
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_SIZE                 0x2000
#define CONFIG_ENV_OFFSET               (10 * CONFIG_SYS_NAND_BLOCK_SIZE)
#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
#define CONFIG_ENV_IS_IN_REMOTE
#define CONFIG_ENV_ADDR         0xffe20000
#define CONFIG_ENV_SIZE         0x2000
#elif defined(CONFIG_ENV_IS_NOWHERE)
#define CONFIG_ENV_SIZE         0x2000
#else
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE         0x2000
#define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */
#endif

#ifndef __ASSEMBLY__
unsigned long get_board_sys_clk(void);
unsigned long get_board_ddr_clk(void);
#endif
#define CONFIG_SYS_CLK_FREQ     get_board_sys_clk() /* sysclk for MPC85xx */
#define CONFIG_DDR_CLK_FREQ     get_board_ddr_clk()

/*
 * These can be toggled for performance analysis, otherwise use default.
 */
#define CONFIG_SYS_CACHE_STASHING
#define CONFIG_BTB                      /* toggle branch predition */
#define CONFIG_DDR_ECC
#ifdef CONFIG_DDR_ECC
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_MEM_INIT_VALUE           0xdeadbeef
#endif

#define CONFIG_ENABLE_36BIT_PHYS

#ifdef CONFIG_PHYS_64BIT
#define CONFIG_ADDR_MAP
#define CONFIG_SYS_NUM_ADDR_MAP         64      /* number of TLB1 entries */
#endif

#if 0
#define CONFIG_POST CONFIG_SYS_POST_MEMORY      /* test POST memory test */
#endif
#define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest works on */
#define CONFIG_SYS_MEMTEST_END          0x00400000
#define CONFIG_SYS_ALT_MEMTEST
#define CONFIG_PANIC_HANG       /* do not reset board on panic */

/*
 *  Config the L3 Cache as L3 SRAM
 */
#define CONFIG_SYS_INIT_L3_ADDR         0xFFFC0000
#define CONFIG_SYS_L3_SIZE              256 << 10
#define CONFIG_SPL_GD_ADDR              (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
#ifdef CONFIG_NAND
#define CONFIG_ENV_ADDR                 (CONFIG_SPL_GD_ADDR + 4 * 1024)
#endif
#define CONFIG_SPL_RELOC_MALLOC_ADDR    (CONFIG_SPL_GD_ADDR + 12 * 1024)
#define CONFIG_SPL_RELOC_MALLOC_SIZE    (30 << 10)
#define CONFIG_SPL_RELOC_STACK          (CONFIG_SPL_GD_ADDR + 64 * 1024)
#define CONFIG_SPL_RELOC_STACK_SIZE     (22 << 10)

#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_DCSRBAR              0xf0000000
#define CONFIG_SYS_DCSRBAR_PHYS         0xf00000000ull
#endif

/* EEPROM */
#define CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM       0
#define CONFIG_SYS_I2C_EEPROM_ADDR      0x57
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5

/*
 * DDR Setup
 */
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
#define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE

#define CONFIG_DIMM_SLOTS_PER_CTLR      1
#define CONFIG_CHIP_SELECTS_PER_CTRL    (4 * CONFIG_DIMM_SLOTS_PER_CTLR)

#define CONFIG_DDR_SPD
#define CONFIG_SYS_DDR_RAW_TIMING
#ifndef CONFIG_SPL_BUILD
#define CONFIG_FSL_DDR_INTERACTIVE
#endif

#define CONFIG_SYS_SPD_BUS_NUM  0
#define SPD_EEPROM_ADDRESS1     0x51
#define SPD_EEPROM_ADDRESS2     0x53

#define SPD_EEPROM_ADDRESS      SPD_EEPROM_ADDRESS1
#define CONFIG_SYS_SDRAM_SIZE   2048    /* for fixed parameter use */

/*
 * IFC Definitions
 */
#define CONFIG_SYS_FLASH_BASE   0xe0000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_FLASH_BASE_PHYS      (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
#else
#define CONFIG_SYS_FLASH_BASE_PHYS      CONFIG_SYS_FLASH_BASE
#endif

#define CONFIG_SYS_NOR0_CSPR_EXT        (0xf)
#define CONFIG_SYS_NOR0_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
                                + 0x8000000) | \
                                CSPR_PORT_SIZE_16 | \
                                CSPR_MSEL_NOR | \
                                CSPR_V)
#define CONFIG_SYS_NOR1_CSPR_EXT        (0xf)
#define CONFIG_SYS_NOR1_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
                                CSPR_PORT_SIZE_16 | \
                                CSPR_MSEL_NOR | \
                                CSPR_V)
#define CONFIG_SYS_NOR_AMASK    IFC_AMASK(128 * 1024 * 1024)
/* NOR Flash Timing Params */
#define CONFIG_SYS_NOR_CSOR     CSOR_NOR_ADM_SHIFT(4)
#define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x01) | \
                                FTIM0_NOR_TEADC(0x04) | \
                                FTIM0_NOR_TEAHC(0x20))
#define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x35) | \
                                FTIM1_NOR_TRAD_NOR(0x1A) |\
                                FTIM1_NOR_TSEQRAD_NOR(0x13))
#define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x01) | \
                                FTIM2_NOR_TCH(0x0E) | \
                                FTIM2_NOR_TWPH(0x0E) | \
                                FTIM2_NOR_TWP(0x1c))
#define CONFIG_SYS_NOR_FTIM3    0x0

#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */

#define CONFIG_SYS_MAX_FLASH_BANKS      2       /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
#define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */

#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS \
                                        + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}

#define CONFIG_FSL_QIXIS        /* use common QIXIS code */
#define CONFIG_FSL_QIXIS_V2
#define QIXIS_BASE              0xffdf0000
#ifdef CONFIG_PHYS_64BIT
#define QIXIS_BASE_PHYS         (0xf00000000ull | QIXIS_BASE)
#else
#define QIXIS_BASE_PHYS         QIXIS_BASE
#endif
#define QIXIS_LBMAP_SWITCH              0x01
#define QIXIS_LBMAP_MASK                0x0f
#define QIXIS_LBMAP_SHIFT               0
#define QIXIS_LBMAP_DFLTBANK            0x00
#define QIXIS_LBMAP_ALTBANK             0x02
#define QIXIS_RST_CTL_RESET             0x31
#define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
#define QIXIS_RCFG_CTL_RECONFIG_START   0x21
#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08

#define CONFIG_SYS_CSPR3_EXT    (0xf)
#define CONFIG_SYS_CSPR3        (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
                                | CSPR_PORT_SIZE_8 \
                                | CSPR_MSEL_GPCM \
                                | CSPR_V)
#define CONFIG_SYS_AMASK3       IFC_AMASK(4 * 1024)
#define CONFIG_SYS_CSOR3        0x0
/* QIXIS Timing parameters for IFC CS3 */
#define CONFIG_SYS_CS3_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
                                        FTIM0_GPCM_TEADC(0x0e) | \
                                        FTIM0_GPCM_TEAHC(0x0e))
#define CONFIG_SYS_CS3_FTIM1            (FTIM1_GPCM_TACO(0x0e) | \
                                        FTIM1_GPCM_TRAD(0x1f))
#define CONFIG_SYS_CS3_FTIM2            (FTIM2_GPCM_TCS(0x0e) | \
                                        FTIM2_GPCM_TCH(0x8) | \
                                        FTIM2_GPCM_TWP(0x1f))
#define CONFIG_SYS_CS3_FTIM3            0x0

/* NAND Flash on IFC */
#define CONFIG_NAND_FSL_IFC
#define CONFIG_SYS_NAND_MAX_ECCPOS      256
#define CONFIG_SYS_NAND_MAX_OOBFREE     2
#define CONFIG_SYS_NAND_BASE            0xff800000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_NAND_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_NAND_BASE)
#else
#define CONFIG_SYS_NAND_BASE_PHYS       CONFIG_SYS_NAND_BASE
#endif

#define CONFIG_SYS_NAND_CSPR_EXT        (0xf)
#define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
                                | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
                                | CSPR_MSEL_NAND        /* MSEL = NAND */ \
                                | CSPR_V)
#define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64 * 1024)

#define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
                                | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
                                | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
                                | CSOR_NAND_RAL_3       /* RAL = 2Byes */ \
                                | CSOR_NAND_PGS_2K      /* Page Size = 2K */ \
                                | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
                                | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/

#define CONFIG_SYS_NAND_ONFI_DETECTION

/* ONFI NAND Flash mode0 Timing Params */
#define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x07) | \
                                        FTIM0_NAND_TWP(0x18)   | \
                                        FTIM0_NAND_TWCHT(0x07) | \
                                        FTIM0_NAND_TWH(0x0a))
#define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x32) | \
                                        FTIM1_NAND_TWBE(0x39)  | \
                                        FTIM1_NAND_TRR(0x0e)   | \
                                        FTIM1_NAND_TRP(0x18))
#define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x0f) | \
                                        FTIM2_NAND_TREH(0x0a) | \
                                        FTIM2_NAND_TWHRE(0x1e))
#define CONFIG_SYS_NAND_FTIM3           0x0

#define CONFIG_SYS_NAND_DDR_LAW         11

#define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE      1
#define CONFIG_CMD_NAND

#define CONFIG_SYS_NAND_BLOCK_SIZE      (128 * 1024)

#if defined(CONFIG_NAND)
#define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
#define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
#define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
#define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
#define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
#define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NOR0_CSPR_EXT
#define CONFIG_SYS_CSPR2                CONFIG_SYS_NOR0_CSPR
#define CONFIG_SYS_AMASK2               CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR2                CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NOR_FTIM3
#else
#define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
#define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR
#define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
#define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NAND_CSPR_EXT
#define CONFIG_SYS_CSPR2                CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK2               CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CSOR2                CONFIG_SYS_NAND_CSOR
#define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NAND_FTIM0
#define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NAND_FTIM1
#define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NAND_FTIM3
#endif
#define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR1_CSPR_EXT
#define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR1_CSPR
#define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3

#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
#else
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
#endif

#if defined(CONFIG_RAMBOOT_PBL)
#define CONFIG_SYS_RAMBOOT
#endif

#define CONFIG_BOARD_EARLY_INIT_R
#define CONFIG_MISC_INIT_R

#define CONFIG_HWCONFIG

/* define to use L1 as initial stack */
#define CONFIG_L1_INIT_RAM
#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR        0xfdd00000      /* Initial L1 address */
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH      0xf
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW       0xfe03c000
/* The assembler doesn't like typecast */
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
        ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
          CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
#else
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS   0xfe03c000 /* Initial L1 address */
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
#endif
#define CONFIG_SYS_INIT_RAM_SIZE                0x00004000

#define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
                                        GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET

#define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
#define CONFIG_SYS_MALLOC_LEN           (4 * 1024 * 1024)

/* Serial Port - controlled on board with jumper J8
 * open - index 2
 * shorted - index 1
 */
#define CONFIG_CONS_INDEX       1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE     1
#define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)

#define CONFIG_SYS_BAUDRATE_TABLE       \
        {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)

/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL              /* Use FSL common I2C driver */
#define CONFIG_SYS_FSL_I2C_SPEED        400000  /* I2C speed in Hz */
#define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
#define CONFIG_SYS_FSL_I2C2_SPEED       400000  /* I2C speed in Hz */
#define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET       0x118000
#define CONFIG_SYS_FSL_I2C2_OFFSET      0x119000

/*
 * RTC configuration
 */
#define RTC
#define CONFIG_RTC_DS3231               1
#define CONFIG_SYS_I2C_RTC_ADDR         0x68

/*
 * RapidIO
 */
#ifdef CONFIG_SYS_SRIO
#ifdef CONFIG_SRIO1
#define CONFIG_SYS_SRIO1_MEM_VIRT       0xa0000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_SRIO1_MEM_PHYS       0xc20000000ull
#else
#define CONFIG_SYS_SRIO1_MEM_PHYS       0xa0000000
#endif
#define CONFIG_SYS_SRIO1_MEM_SIZE       0x10000000      /* 256M */
#endif

#ifdef CONFIG_SRIO2
#define CONFIG_SYS_SRIO2_MEM_VIRT       0xb0000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_SRIO2_MEM_PHYS       0xc30000000ull
#else
#define CONFIG_SYS_SRIO2_MEM_PHYS       0xb0000000
#endif
#define CONFIG_SYS_SRIO2_MEM_SIZE       0x10000000      /* 256M */
#endif
#endif

/*
 * for slave u-boot IMAGE instored in master memory space,
 * PHYS must be aligned based on the SIZE
 */
#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000       /* 1M */
#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
/*
 * for slave UCODE and ENV instored in master memory space,
 * PHYS must be aligned based on the SIZE
 */
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000    /* 256K */

/* slave core release by master*/
#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */

/*
 * SRIO_PCIE_BOOT - SLAVE
 */
#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
                (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
#endif

/*
 * eSPI - Enhanced SPI
 */
#define CONFIG_SF_DEFAULT_SPEED         10000000
#define CONFIG_SF_DEFAULT_MODE          0

/*
 * MAPLE
 */
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_MAPLE_MEM_PHYS      0xFA0000000ull
#else
#define CONFIG_SYS_MAPLE_MEM_PHYS      0xA0000000
#endif

/*
 * General PCI
 * Memory space is mapped 1-1, but I/O space must start from 0.
 */

/* controller 1, direct to uli, tgtid 3, Base address 20000 */
#define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE1_MEM_BUS        0xe0000000
#define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
#else
#define CONFIG_SYS_PCIE1_MEM_BUS        0x80000000
#define CONFIG_SYS_PCIE1_MEM_PHYS       0x80000000
#endif
#define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
#define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
#define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull
#else
#define CONFIG_SYS_PCIE1_IO_PHYS        0xf8000000
#endif
#define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */

/* Qman/Bman */
#ifndef CONFIG_NOBQFMAN
#define CONFIG_SYS_DPAA_QBMAN           /* Support Q/Bman */
#define CONFIG_SYS_BMAN_NUM_PORTALS     25
#define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
#else
#define CONFIG_SYS_BMAN_MEM_PHYS        CONFIG_SYS_BMAN_MEM_BASE
#endif
#define CONFIG_SYS_BMAN_MEM_SIZE        0x02000000
#define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
#define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
#define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
#define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
                                        CONFIG_SYS_BMAN_CENA_SIZE)
#define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_BMAN_SWP_ISDR_REG    0xE08
#define CONFIG_SYS_QMAN_NUM_PORTALS     25
#define CONFIG_SYS_QMAN_MEM_BASE        0xf6000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_QMAN_MEM_PHYS        0xff6000000ull
#else
#define CONFIG_SYS_QMAN_MEM_PHYS        CONFIG_SYS_QMAN_MEM_BASE
#endif
#define CONFIG_SYS_QMAN_MEM_SIZE        0x02000000
#define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
#define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
#define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
#define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
                                        CONFIG_SYS_QMAN_CENA_SIZE)
#define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_QMAN_SWP_ISDR_REG    0xE08

#define CONFIG_SYS_DPAA_FMAN

#define CONFIG_SYS_DPAA_RMAN

/* Default address of microcode for the Linux Fman driver */
#if defined(CONFIG_SPIFLASH)
/*
 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
 * env, so we got 0x110000.
 */
#define CONFIG_SYS_QE_FW_IN_SPIFLASH
#define CONFIG_SYS_FMAN_FW_ADDR 0x110000
#elif defined(CONFIG_SDCARD)
/*
 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 * about 545KB (1089 blocks), Env is stored after the image, and the env size is
 * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130.
 */
#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
#define CONFIG_SYS_FMAN_FW_ADDR (512 * 1130)
#elif defined(CONFIG_NAND)
#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
#define CONFIG_SYS_FMAN_FW_ADDR (13 * CONFIG_SYS_NAND_BLOCK_SIZE)
#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
/*
 * Slave has no ucode locally, it can fetch this from remote. When implementing
 * in two corenet boards, slave's ucode could be stored in master's memory
 * space, the address can be mapped from slave TLB->slave LAW->
 * slave SRIO or PCIE outbound window->master inbound window->
 * master LAW->the ucode address in master's memory space.
 */
#define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
#define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000
#else
#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
#define CONFIG_SYS_FMAN_FW_ADDR         0xEFF00000
#endif
#define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
#define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
#endif /* CONFIG_NOBQFMAN */

#ifdef CONFIG_SYS_DPAA_FMAN
#define CONFIG_FMAN_ENET
#define CONFIG_PHYLIB_10G
#define CONFIG_PHY_VITESSE
#define CONFIG_PHY_TERANETICS
#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
#define SGMII_CARD_PORT2_PHY_ADDR 0x10
#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
#define SGMII_CARD_PORT4_PHY_ADDR 0x11
#endif

#ifdef CONFIG_PCI
#define CONFIG_PCI_INDIRECT_BRIDGE

#define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
#endif  /* CONFIG_PCI */

#ifdef CONFIG_FMAN_ENET
#define CONFIG_SYS_FM1_ONBOARD_PHY1_ADDR 0x10
#define CONFIG_SYS_FM1_ONBOARD_PHY2_ADDR 0x11

/*B4860 QDS AMC2PEX-2S default PHY_ADDR */
#define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 0x7       /*SLOT 1*/
#define CONFIG_SYS_FM1_10GEC2_PHY_ADDR 0x6       /*SLOT 2*/

#define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR    0x1c
#define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR    0x1d
#define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR    0x1e
#define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR    0x1f

#define CONFIG_MII              /* MII PHY management */
#define CONFIG_ETHPRIME         "FM1@DTSEC1"
#define CONFIG_PHY_GIGE         /* Include GbE speed/duplex detection */
#endif

#define CONFIG_SYS_FSL_B4860QDS_XFI_ERR

/*
 * Environment
 */
#define CONFIG_LOADS_ECHO               /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change */

/*
 * Command line configuration.
 */
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_ERRATA
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_REGINFO

#ifdef CONFIG_PCI
#define CONFIG_CMD_PCI
#endif

/* Hash command with SHA acceleration supported in hardware */
#ifdef CONFIG_FSL_CAAM
#define CONFIG_CMD_HASH
#define CONFIG_SHA_HW_ACCEL
#endif

/*
* USB
*/
#define CONFIG_HAS_FSL_DR_USB

#ifdef CONFIG_HAS_FSL_DR_USB
#define CONFIG_USB_EHCI

#ifdef CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif
#endif

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP                     /* undef to save memory */
#define CONFIG_CMDLINE_EDITING                  /* Command-line editing */
#define CONFIG_AUTO_COMPLETE                    /* add autocompletion support */
#define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
#ifdef CONFIG_CMD_KGDB
#define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS      16              /* max number of command args */
#define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 64 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial map for Linux*/
#define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */

#ifdef CONFIG_CMD_KGDB
#define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
#endif

/*
 * Environment Configuration
 */
#define CONFIG_ROOTPATH         "/opt/nfsroot"
#define CONFIG_BOOTFILE         "uImage"
#define CONFIG_UBOOTPATH        "u-boot.bin"    /* U-Boot image on TFTP server*/

/* default location for tftp and bootm */
#define CONFIG_LOADADDR         1000000

#define __USB_PHY_TYPE  ulpi

#ifdef CONFIG_ARCH_B4860
#define HWCONFIG        "hwconfig=fsl_ddr:ctlr_intlv=null,"     \
                        "bank_intlv=cs0_cs1;"   \
                        "en_cpc:cpc2;"
#else
#define HWCONFIG        "hwconfig=fsl_ddr:ctlr_intlv=null,bank_intlv=cs0_cs1;"
#endif

#define CONFIG_EXTRA_ENV_SETTINGS                               \
        HWCONFIG                                                \
        "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
        "netdev=eth0\0"                                         \
        "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"                     \
        "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"                     \
        "tftpflash=tftpboot $loadaddr $uboot && "               \
        "protect off $ubootaddr +$filesize && "                 \
        "erase $ubootaddr +$filesize && "                       \
        "cp.b $loadaddr $ubootaddr $filesize && "               \
        "protect on $ubootaddr +$filesize && "                  \
        "cmp.b $loadaddr $ubootaddr $filesize\0"                \
        "consoledev=ttyS0\0"                                    \
        "ramdiskaddr=2000000\0"                                 \
        "ramdiskfile=b4860qds/ramdisk.uboot\0"                  \
        "fdtaddr=1e00000\0"                                     \
        "fdtfile=b4860qds/b4860qds.dtb\0"                               \
        "bdev=sda3\0"

/* For emulation this causes u-boot to jump to the start of the proof point
   app code automatically */
#define CONFIG_PROOF_POINTS                     \
 "setenv bootargs root=/dev/$bdev rw "          \
 "console=$consoledev,$baudrate $othbootargs;"  \
 "cpu 1 release 0x29000000 - - -;"              \
 "cpu 2 release 0x29000000 - - -;"              \
 "cpu 3 release 0x29000000 - - -;"              \
 "cpu 4 release 0x29000000 - - -;"              \
 "cpu 5 release 0x29000000 - - -;"              \
 "cpu 6 release 0x29000000 - - -;"              \
 "cpu 7 release 0x29000000 - - -;"              \
 "go 0x29000000"

#define CONFIG_HVBOOT   \
 "setenv bootargs config-addr=0x60000000; "     \
 "bootm 0x01000000 - 0x00f00000"

#define CONFIG_ALU                              \
 "setenv bootargs root=/dev/$bdev rw "          \
 "console=$consoledev,$baudrate $othbootargs;"  \
 "cpu 1 release 0x01000000 - - -;"              \
 "cpu 2 release 0x01000000 - - -;"              \
 "cpu 3 release 0x01000000 - - -;"              \
 "cpu 4 release 0x01000000 - - -;"              \
 "cpu 5 release 0x01000000 - - -;"              \
 "cpu 6 release 0x01000000 - - -;"              \
 "cpu 7 release 0x01000000 - - -;"              \
 "go 0x01000000"

#define CONFIG_LINUX                            \
 "setenv bootargs root=/dev/ram rw "            \
 "console=$consoledev,$baudrate $othbootargs;"  \
 "setenv ramdiskaddr 0x02000000;"               \
 "setenv fdtaddr 0x01e00000;"                   \
 "setenv loadaddr 0x1000000;"                   \
 "bootm $loadaddr $ramdiskaddr $fdtaddr"

#define CONFIG_HDBOOT                                   \
        "setenv bootargs root=/dev/$bdev rw "           \
        "console=$consoledev,$baudrate $othbootargs;"   \
        "tftp $loadaddr $bootfile;"                     \
        "tftp $fdtaddr $fdtfile;"                       \
        "bootm $loadaddr - $fdtaddr"

#define CONFIG_NFSBOOTCOMMAND                   \
        "setenv bootargs root=/dev/nfs rw "     \
        "nfsroot=$serverip:$rootpath "          \
        "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
        "console=$consoledev,$baudrate $othbootargs;"   \
        "tftp $loadaddr $bootfile;"             \
        "tftp $fdtaddr $fdtfile;"               \
        "bootm $loadaddr - $fdtaddr"

#define CONFIG_RAMBOOTCOMMAND                           \
        "setenv bootargs root=/dev/ram rw "             \
        "console=$consoledev,$baudrate $othbootargs;"   \
        "tftp $ramdiskaddr $ramdiskfile;"               \
        "tftp $loadaddr $bootfile;"                     \
        "tftp $fdtaddr $fdtfile;"                       \
        "bootm $loadaddr $ramdiskaddr $fdtaddr"

#define CONFIG_BOOTCOMMAND              CONFIG_LINUX

#include <asm/fsl_secure_boot.h>

#endif  /* __CONFIG_H */