uboot/include/configs/am335x_shc.h
<<
>>
Prefs
   1/*
   2 * (C) Copyright 2016
   3 * Heiko Schocher, DENX Software Engineering, hs@denx.de.
   4 *
   5 * Based on:
   6 * am335x_evm.h
   7 *
   8 * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
   9 *
  10 * SPDX-License-Identifier:     GPL-2.0+
  11 */
  12
  13#ifndef __CONFIG_AM335X_SHC_H
  14#define __CONFIG_AM335X_SHC_H
  15
  16#include <configs/ti_am335x_common.h>
  17
  18/* settings we don;t want on this board */
  19#undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC
  20#undef CONFIG_CMD_EXT4
  21#undef CONFIG_CMD_EXT4_WRITE
  22#undef CONFIG_CMD_MMC_SPI
  23#undef CONFIG_CMD_SPI
  24
  25#define CONFIG_CMD_CACHE
  26
  27#ifndef CONFIG_SPL_BUILD
  28# define CONFIG_TIMESTAMP
  29# define CONFIG_LZO
  30#endif
  31
  32#define CONFIG_SYS_BOOTM_LEN            (16 << 20)
  33
  34/* Clock Defines */
  35#define V_OSCK                          24000000  /* Clock output from T2 */
  36#define V_SCLK                          (V_OSCK)
  37
  38#define CONFIG_ENV_IS_IN_MMC            1
  39
  40/*
  41 * in case of SD Card or Network boot we want to have a possibility to
  42 * debrick the shc, therefore do not read environment from eMMC
  43 */
  44#if defined(CONFIG_SHC_SDBOOT) || defined(CONFIG_SHC_NETBOOT)
  45#define CONFIG_SYS_MMC_ENV_DEV          0
  46#else
  47#define CONFIG_SYS_MMC_ENV_DEV          1
  48#endif
  49
  50/*
  51 * Info when using boot partitions: As environment resides within first
  52 * 128 kB, MLO must start at 128 kB == 0x20000
  53 * ENV at MMC Boot0 Partition - 0/Undefined=user, 1=boot0, 2=boot1,
  54 * 4..7=general0..3
  55 */
  56#define CONFIG_ENV_SIZE                         0x1000 /* 4 KB */
  57#define CONFIG_ENV_OFFSET                       0x7000 /* 28 kB */
  58
  59#define CONFIG_HSMMC2_8BIT
  60
  61#define CONFIG_ENV_OFFSET_REDUND    0x9000 /* 36 kB */
  62#define CONFIG_ENV_SIZE_REDUND      CONFIG_ENV_SIZE
  63
  64#ifndef CONFIG_SHC_ICT
  65/*
  66 * In builds other than ICT, reset to retry after timeout
  67 * Define a timeout after which a stopped bootloader continues autoboot
  68 * (only works with CONFIG_RESET_TO_RETRY)
  69 */
  70# define CONFIG_BOOT_RETRY_TIME 30
  71# define CONFIG_RESET_TO_RETRY
  72#endif
  73
  74#define CONFIG_ENV_VARS_UBOOT_CONFIG
  75#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
  76
  77#ifndef CONFIG_SPL_BUILD
  78#define CONFIG_EXTRA_ENV_SETTINGS \
  79        "loadaddr=0x80200000\0" \
  80        "kloadaddr=0x84000000\0" \
  81        "fdtaddr=0x85000000\0" \
  82        "fdt_high=0xffffffff\0" \
  83        "rdaddr=0x81000000\0" \
  84        "bootfile=uImage\0" \
  85        "fdtfile=am335x-shc.dtb\0" \
  86        "verify=no\0" \
  87        "serverip=10.55.152.184\0" \
  88        "rootpath=/srv/nfs/shc-rootfs\0" \
  89        "console=ttyO0,115200n8\0" \
  90        "optargs=quiet\0" \
  91        "mmcdev=1\0" \
  92        "harakiri=0\0" \
  93        "mmcpart=2\0" \
  94        "active_root=root1\0" \
  95        "inactive_root=root2\0" \
  96        "mmcrootfstype=ext4 rootwait\0" \
  97        "nfsopts=nolock\0" \
  98        "static_ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}" \
  99                "::off\0" \
 100        "ip_method=none\0" \
 101        "bootargs_defaults=setenv bootargs " \
 102                "console=${console} " \
 103                "${optargs}\0" \
 104        "mmcargs=run bootargs_defaults;" \
 105                "setenv bootargs ${bootargs} " \
 106                "root=${mmcroot} " \
 107                "rootfstype=${mmcrootfstype} ip=${ip_method}\0" \
 108        "netargs=setenv bootargs console=${console} " \
 109                "${optargs} " \
 110                "root=/dev/nfs " \
 111                "nfsroot=${serverip}:${rootpath},${nfsopts} rw " \
 112                "ip=dhcp\0" \
 113        "bootenv=uEnv.txt\0" \
 114        "loadbootenv=if fatload mmc ${mmcdev} ${loadaddr} ${bootenv}; then " \
 115                        "echo Loaded environment from ${bootenv}; " \
 116                        "run importbootenv; " \
 117                "fi;\0" \
 118        "importbootenv=echo Importing environment variables from uEnv.txt ...; " \
 119                "env import -t $loadaddr $filesize\0" \
 120        "loaduimagefat=fatload mmc ${mmcdev} ${kloadaddr} ${bootfile}\0" \
 121        "loaduimage=ext2load mmc ${mmcdev}:${mmcpart} ${kloadaddr} /boot/${bootfile}\0" \
 122        "loadfdt=ext2load mmc ${mmcdev}:${mmcpart} ${fdtaddr} /boot/${fdtfile}\0" \
 123        "netloaduimage=tftp ${loadaddr} ${bootfile}\0" \
 124        "netloadfdt=tftp ${fdtaddr} ${fdtfile}\0" \
 125        "mmcboot=echo Booting Linux from ${mmcdevice} ...; " \
 126                "run mmcargs; " \
 127                "if run loadfdt; then " \
 128                        "echo device tree detected; " \
 129                        "bootm ${kloadaddr} - ${fdtaddr}; " \
 130                "else " \
 131                        "bootm ${kloadaddr}; " \
 132                "fi; \0" \
 133        "netboot=echo Booting from network ...; " \
 134                "setenv autoload no; " \
 135                "dhcp; " \
 136                "run netloaduimage; " \
 137                "run netargs; " \
 138                "echo NFS path: ${serverip}:${rootpath};" \
 139                "if run netloadfdt; then " \
 140                        "echo device tree detected; " \
 141                        "bootm ${loadaddr} - ${fdtaddr}; " \
 142                "else " \
 143                        "bootm ${loadaddr}; " \
 144                "fi; \0" \
 145        "emmc_erase=if test ${harakiri} = 1 ; then echo erase emmc ...; setenv mmcdev 1; mmc erase 0 200; reset; fi; \0" \
 146        "mmcpart_gp=mmcpart gp 1 40; \0" \
 147        "mmcpart_enhance=mmcpart enhance 0 64; \0" \
 148        "mmcpart_rel_write=mmcpart rel_write 1f; \0" \
 149        "mmcpart_commit=mmcpart commit 1; \0" \
 150        "mmc_hw_part=run mmcpart_gp; run mmcpart_enhance; run mmcpart_rel_write; run mmcpart_commit; \0" \
 151        "led_success=gpio set 22; \0" \
 152        "fusecmd=mmc dev 1; if mmcpart iscommitted; then echo HW Partitioning already committed; mmcpart list; else run mmc_hw_part; fi; run led_success; \0" \
 153        "uenv_exec=if test -n $uenvcmd; then " \
 154                        "echo Running uenvcmd ...; " \
 155                        "run uenvcmd; " \
 156                "fi;\0" \
 157        "sd_setup=echo SD/MMC-Card detected on device 0; " \
 158                "setenv mmcdevice SD; " \
 159                "setenv mmcdev 0; " \
 160                "setenv mmcpart 2; " \
 161                "setenv mmcroot /dev/mmcblk${mmcdev}p${mmcpart};\0" \
 162        "emmc_setup=echo eMMC detected on device 1; " \
 163                "setenv mmcdevice eMMC; " \
 164                "setenv mmcdev 1; " \
 165                "run emmc_erase; " \
 166                "if test ${active_root} = root2; then " \
 167                        "echo Active root is partition 6 (root2); " \
 168                        "setenv mmcpart 6; " \
 169                "else " \
 170                        "echo Active root is partition 5 (root1); " \
 171                        "setenv mmcpart 5; " \
 172                "fi; " \
 173                "setenv mmcroot /dev/mmcblk${mmcdev}p${mmcpart};\0"
 174#endif /* #ifndef CONFIG_SPL_BUILD */
 175
 176#if defined CONFIG_SHC_NETBOOT
 177/* Network Boot */
 178# define CONFIG_BOOTCOMMAND \
 179        "run fusecmd; " \
 180        "if run netboot; then " \
 181                "echo Booting from network; " \
 182        "else " \
 183                "echo ERROR: Cannot boot from network!; " \
 184                "panic; " \
 185        "fi; "
 186
 187#elif defined CONFIG_SHC_SDBOOT /* !defined CONFIG_SHC_NETBOOT */
 188/* SD-Card Boot */
 189# define CONFIG_BOOTCOMMAND \
 190        "if mmc dev 0; mmc rescan; then " \
 191                "run sd_setup; " \
 192        "else " \
 193                "echo ERROR: SD/MMC-Card not detected!; " \
 194                "panic; " \
 195        "fi; " \
 196        "if run loaduimage; then " \
 197                "echo Bootable SD/MMC-Card inserted, booting from it!; " \
 198                "run mmcboot; " \
 199        "else " \
 200                "echo ERROR: Unable to load uImage from SD/MMC-Card!; " \
 201                "panic; " \
 202        "fi; "
 203
 204#elif defined CONFIG_SHC_ICT
 205/* ICT adapter boots only u-boot and does HW partitioning */
 206# define CONFIG_BOOTCOMMAND \
 207        "if mmc dev 0; mmc rescan; then " \
 208                "run sd_setup; " \
 209        "else " \
 210                "echo ERROR: SD/MMC-Card not detected!; " \
 211                "panic; " \
 212        "fi; " \
 213        "run fusecmd; "
 214
 215#else /* !defined CONFIG_SHC_NETBOOT, !defined CONFIG_SHC_SDBOOT */
 216/* Regular Boot from internal eMMC */
 217# define CONFIG_BOOTCOMMAND \
 218        "if mmc dev 1; mmc rescan; then " \
 219                "run emmc_setup; " \
 220        "else " \
 221                "echo ERROR: eMMC device not detected!; " \
 222                "panic; " \
 223        "fi; " \
 224        "if run loaduimage; then " \
 225                "run mmcboot; " \
 226        "else " \
 227                "echo ERROR Unable to load uImage from eMMC!; " \
 228                "echo Performing Rollback!; " \
 229                "setenv _active_ ${active_root}; " \
 230                "setenv _inactive_ ${inactive_root}; " \
 231                "setenv active_root ${_inactive_}; " \
 232                "setenv inactive_root ${_active_}; " \
 233                "saveenv; " \
 234                "reset; " \
 235        "fi; "
 236
 237#endif /* Regular Boot */
 238
 239/* NS16550 Configuration */
 240#define CONFIG_SYS_NS16550_COM1         0x44e09000      /* UART0 */
 241#define CONFIG_SYS_NS16550_COM2         0x48022000      /* UART1 */
 242#define CONFIG_SYS_NS16550_COM3         0x48024000      /* UART2 */
 243#define CONFIG_SYS_NS16550_COM4         0x481a6000      /* UART3 */
 244#define CONFIG_SYS_NS16550_COM5         0x481a8000      /* UART4 */
 245#define CONFIG_SYS_NS16550_COM6         0x481aa000      /* UART5 */
 246#define CONFIG_CONS_INDEX               1
 247
 248/* PMIC support */
 249#define CONFIG_POWER_TPS65217
 250
 251/* SPL */
 252
 253#define CONFIG_SPL_LDSCRIPT             "arch/arm/mach-omap2/am33xx/u-boot-spl.lds"
 254
 255#ifndef CONFIG_SPL_USBETH_SUPPORT
 256#define CONFIG_FASTBOOT_FLASH_MMC_DEV   1
 257#endif
 258
 259/*
 260 * Disable MMC DM for SPL build and can be re-enabled after adding
 261 * DM support in SPL
 262 */
 263#ifdef CONFIG_SPL_BUILD
 264#undef CONFIG_DM_MMC
 265#undef CONFIG_TIMER
 266#endif
 267
 268#define CONFIG_CMD_DHCP
 269#define CONFIG_CMD_PING
 270#define CONFIG_DRIVER_TI_CPSW
 271#define CONFIG_MII
 272#define CONFIG_BOOTP_DEFAULT
 273#define CONFIG_BOOTP_DNS
 274#define CONFIG_BOOTP_DNS2
 275#define CONFIG_BOOTP_SEND_HOSTNAME
 276#define CONFIG_BOOTP_GATEWAY
 277#define CONFIG_BOOTP_SUBNETMASK
 278#define CONFIG_NET_RETRY_COUNT         10
 279#define CONFIG_NET_MULTI
 280#define CONFIG_PHY_GIGE
 281#define CONFIG_PHYLIB
 282#define CONFIG_PHY_ADDR                 0
 283#define CONFIG_PHY_SMSC
 284
 285/* I2C configuration */
 286#define CONFIG_SYS_I2C_EEPROM_ADDR      0x50    /* Main EEPROM */
 287#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  2
 288#define CONFIG_SYS_I2C_SPEED            400000
 289#define CONFIG_SYS_I2C_SLAVE            1
 290
 291#define CONFIG_SHOW_BOOT_PROGRESS
 292
 293#if defined CONFIG_SHC_NETBOOT
 294#ifdef CONFIG_SPL_BUILD
 295#define CONFIG_ENV_IS_NOWHERE
 296#undef CONFIG_ENV_IS_IN_MMC
 297#endif
 298#endif
 299#endif  /* ! __CONFIG_AM335X_SHC_H */
 300