1/* 2 * Copyright 2013 Broadcom Corporation. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7#ifndef __BCM23550_W1D_H 8#define __BCM23550_W1D_H 9 10#include <linux/sizes.h> 11#include <asm/arch/sysmap.h> 12 13/* CPU, chip, mach, etc */ 14#define CONFIG_KONA 15#define CONFIG_SKIP_LOWLEVEL_INIT 16#define CONFIG_KONA_RESET_S 17 18/* 19 * Memory configuration 20 */ 21#define CONFIG_SYS_TEXT_BASE 0x9f000000 22 23#define CONFIG_SYS_SDRAM_BASE 0x80000000 24#define CONFIG_SYS_SDRAM_SIZE 0x20000000 25#define CONFIG_NR_DRAM_BANKS 1 26 27#define CONFIG_SYS_MALLOC_LEN SZ_4M /* see armv7/start.S. */ 28 29/* GPIO Driver */ 30#define CONFIG_KONA_GPIO 31 32/* MMC/SD Driver */ 33#define CONFIG_SYS_SDIO_BASE0 SDIO1_BASE_ADDR 34#define CONFIG_SYS_SDIO_BASE1 SDIO2_BASE_ADDR 35#define CONFIG_SYS_SDIO_BASE2 SDIO3_BASE_ADDR 36#define CONFIG_SYS_SDIO_BASE3 SDIO4_BASE_ADDR 37#define CONFIG_SYS_SDIO0_MAX_CLK 48000000 38#define CONFIG_SYS_SDIO1_MAX_CLK 48000000 39#define CONFIG_SYS_SDIO2_MAX_CLK 48000000 40#define CONFIG_SYS_SDIO3_MAX_CLK 48000000 41#define CONFIG_SYS_SDIO0 "sdio1" 42#define CONFIG_SYS_SDIO1 "sdio2" 43#define CONFIG_SYS_SDIO2 "sdio3" 44#define CONFIG_SYS_SDIO3 "sdio4" 45 46/* I2C Driver */ 47#define CONFIG_SYS_I2C 48#define CONFIG_SYS_I2C_KONA 49#define CONFIG_SYS_SPD_BUS_NUM 3 /* Start with PMU bus */ 50#define CONFIG_SYS_MAX_I2C_BUS 4 51#define CONFIG_SYS_I2C_BASE0 BSC1_BASE_ADDR 52#define CONFIG_SYS_I2C_BASE1 BSC2_BASE_ADDR 53#define CONFIG_SYS_I2C_BASE2 BSC3_BASE_ADDR 54#define CONFIG_SYS_I2C_BASE3 PMU_BSC_BASE_ADDR 55 56/* Timer Driver */ 57#define CONFIG_SYS_TIMER_RATE 32000 58#define CONFIG_SYS_TIMER_COUNTER (TIMER_BASE_ADDR + 4) /* STCLO offset */ 59 60/* Init functions */ 61#define CONFIG_MISC_INIT_R /* board's misc_init_r function */ 62 63/* Some commands use this as the default load address */ 64#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE 65 66/* No mtest functions as recommended */ 67 68/* 69 * This is the initial SP which is used only briefly for relocating the u-boot 70 * image to the top of SDRAM. After relocation u-boot moves the stack to the 71 * proper place. 72 */ 73#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE 74 75/* Serial Info */ 76#define CONFIG_SYS_NS16550_SERIAL 77/* Post pad 3 bytes after each reg addr */ 78#define CONFIG_SYS_NS16550_REG_SIZE (-4) 79#define CONFIG_SYS_NS16550_CLK 13000000 80#define CONFIG_CONS_INDEX 1 81#define CONFIG_SYS_NS16550_COM1 0x3e000000 82 83/* must fit into GPT:u-boot-env partition */ 84#define CONFIG_ENV_IS_IN_MMC 85#define CONFIG_SYS_MMC_ENV_DEV 0 86#define CONFIG_ENV_OFFSET (0x00011a00 * 512) 87#define CONFIG_ENV_SIZE (8 * 512) 88 89/* console configuration */ 90#define CONFIG_SYS_CBSIZE 1024 /* Console buffer size */ 91#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 92 sizeof(CONFIG_SYS_PROMPT) + 16) /* Printbuffer size */ 93#define CONFIG_SYS_MAXARGS 64 94#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 95 96/* 97 * One partition type must be defined for part.c 98 * This is necessary for the fatls command to work on an SD card 99 * for example. 100 */ 101 102/* version string, parser, etc */ 103#define CONFIG_AUTO_COMPLETE 104#define CONFIG_CMDLINE_EDITING 105#define CONFIG_SYS_LONGHELP 106 107#define CONFIG_CRC32_VERIFY 108#define CONFIG_MX_CYCLIC 109 110/* Initial upstream - boot to cmd prompt only */ 111#define CONFIG_BOOTCOMMAND "" 112 113/* Commands */ 114#define CONFIG_FAT_WRITE 115 116#undef CONFIG_USB_GADGET_VBUS_DRAW 117#define CONFIG_USB_GADGET_VBUS_DRAW 0 118#define CONFIG_USBID_ADDR 0x34052c46 119 120#define CONFIG_SYS_ICACHE_OFF 121#define CONFIG_SYS_DCACHE_OFF 122#define CONFIG_SYS_L2CACHE_OFF 123 124#endif /* __BCM23550_W1D_H */ 125