/*
 * Copyright 2013 Freescale Semiconductor, Inc.
 *
 * SPDX-License-Identifier:     GPL-2.0+
 */

/*
 * BSC9132 QDS board configuration file
 */

#ifndef __CONFIG_H
#define __CONFIG_H

#define CONFIG_MISC_INIT_R

#ifdef CONFIG_SDCARD
#define CONFIG_RAMBOOT_SDCARD
#define CONFIG_SYS_RAMBOOT
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_SYS_TEXT_BASE            0x11000000
#define CONFIG_RESET_VECTOR_ADDRESS     0x110bfffc
#endif
#ifdef CONFIG_SPIFLASH
#define CONFIG_RAMBOOT_SPIFLASH
#define CONFIG_SYS_RAMBOOT
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_SYS_TEXT_BASE            0x11000000
#define CONFIG_RESET_VECTOR_ADDRESS     0x110bfffc
#endif
#ifdef CONFIG_NAND_SECBOOT
#define CONFIG_RAMBOOT_NAND
#define CONFIG_SYS_RAMBOOT
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_SYS_TEXT_BASE            0x11000000
#define CONFIG_RESET_VECTOR_ADDRESS     0x110bfffc
#endif

#ifdef CONFIG_NAND
#define CONFIG_SPL_INIT_MINIMAL
#define CONFIG_SPL_NAND_BOOT
#define CONFIG_SPL_FLUSH_IMAGE
#define CONFIG_SPL_TARGET               "u-boot-with-spl.bin"

#define CONFIG_SYS_TEXT_BASE            0x00201000
#define CONFIG_SPL_TEXT_BASE            0xFFFFE000
#define CONFIG_SPL_MAX_SIZE             8192
#define CONFIG_SPL_RELOC_TEXT_BASE      0x00100000
#define CONFIG_SPL_RELOC_STACK          0x00100000
#define CONFIG_SYS_NAND_U_BOOT_SIZE     ((768 << 10) - 0x2000)
#define CONFIG_SYS_NAND_U_BOOT_DST      (0x00200000 - CONFIG_SPL_MAX_SIZE)
#define CONFIG_SYS_NAND_U_BOOT_START    0x00200000
#define CONFIG_SYS_NAND_U_BOOT_OFFS     0
#define CONFIG_SYS_LDSCRIPT     "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
#endif

#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE            0x8ff40000
#endif

#ifndef CONFIG_RESET_VECTOR_ADDRESS
#define CONFIG_RESET_VECTOR_ADDRESS     0x8ffffffc
#endif

#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
#else
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
#endif

/* High Level Configuration Options */
#define CONFIG_SYS_HAS_SERDES           /* common SERDES init code */

#if defined(CONFIG_PCI)
#define CONFIG_PCIE1                    /* PCIE controller 1 (slot 1) */
#define CONFIG_FSL_PCI_INIT             /* Use common FSL init code */
#define CONFIG_PCI_INDIRECT_BRIDGE      /* indirect PCI bridge support */
#define CONFIG_FSL_PCIE_RESET           /* need PCIe reset errata */
#define CONFIG_SYS_PCI_64BIT            /* enable 64-bit PCI resources */

/*
 * PCI Windows
 * Memory space is mapped 1-1, but I/O space must start from 0.
 */
/* controller 1, Slot 1, tgtid 1, Base address a000 */
#define CONFIG_SYS_PCIE1_NAME           "PCIe Slot"
#define CONFIG_SYS_PCIE1_MEM_VIRT       0x90000000
#define CONFIG_SYS_PCIE1_MEM_BUS        0x90000000
#define CONFIG_SYS_PCIE1_MEM_PHYS       0x90000000
#define CONFIG_SYS_PCIE1_MEM_SIZE       0x10000000      /* 256M */
#define CONFIG_SYS_PCIE1_IO_VIRT        0xC0010000
#define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
#define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */
#define CONFIG_SYS_PCIE1_IO_PHYS        0xC0010000

#define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
#endif

#define CONFIG_ENV_OVERWRITE
#define CONFIG_TSEC_ENET /* ethernet */

#if defined(CONFIG_SYS_CLK_100_DDR_100)
#define CONFIG_SYS_CLK_FREQ     100000000
#define CONFIG_DDR_CLK_FREQ     100000000
#elif defined(CONFIG_SYS_CLK_100_DDR_133)
#define CONFIG_SYS_CLK_FREQ     100000000
#define CONFIG_DDR_CLK_FREQ     133000000
#endif

#define CONFIG_MP

#define CONFIG_HWCONFIG
/*
 * These can be toggled for performance analysis, otherwise use default.
 */
#define CONFIG_L2_CACHE                 /* toggle L2 cache */
#define CONFIG_BTB                      /* enable branch predition */

#define CONFIG_SYS_MEMTEST_START        0x01000000      /* memtest works on */
#define CONFIG_SYS_MEMTEST_END          0x01ffffff

/* DDR Setup */
#define CONFIG_SYS_SPD_BUS_NUM          0
#define SPD_EEPROM_ADDRESS1             0x54 /* I2C access */
#define SPD_EEPROM_ADDRESS2             0x56 /* I2C access */
#define CONFIG_FSL_DDR_INTERACTIVE

#define CONFIG_MEM_INIT_VALUE           0xDeadBeef

#define CONFIG_SYS_SDRAM_SIZE           (1024)
#define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
#define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE

#define CONFIG_DIMM_SLOTS_PER_CTLR      1

/* DDR3 Controller Settings */
#define CONFIG_CHIP_SELECTS_PER_CTRL    1
#define CONFIG_SYS_DDR_CS0_BNDS         0x0000003F
#define CONFIG_SYS_DDR_CS0_CONFIG_1333  0x80004302
#define CONFIG_SYS_DDR_CS0_CONFIG_800   0x80014302
#define CONFIG_SYS_DDR_CS0_CONFIG_2     0x00000000
#define CONFIG_SYS_DDR_DATA_INIT        0xdeadbeef
#define CONFIG_SYS_DDR_INIT_ADDR        0x00000000
#define CONFIG_SYS_DDR_INIT_EXT_ADDR    0x00000000
#define CONFIG_SYS_DDR_MODE_CONTROL     0x00000000
#define CONFIG_SYS_DDR1_CS0_BNDS       0x0040007F

#define CONFIG_SYS_DDR_ZQ_CONTROL       0x89080600
#define CONFIG_SYS_DDR_SR_CNTR          0x00000000
#define CONFIG_SYS_DDR_RCW_1            0x00000000
#define CONFIG_SYS_DDR_RCW_2            0x00000000
#define CONFIG_SYS_DDR_CONTROL_800              0x470C0000
#define CONFIG_SYS_DDR_CONTROL_2_800    0x04401050
#define CONFIG_SYS_DDR_TIMING_4_800             0x00220001
#define CONFIG_SYS_DDR_TIMING_5_800             0x03402400

#define CONFIG_SYS_DDR_CONTROL_1333             0x470C0008
#define CONFIG_SYS_DDR_CONTROL_2_1333   0x24401010
#define CONFIG_SYS_DDR_TIMING_4_1333            0x00000001
#define CONFIG_SYS_DDR_TIMING_5_1333            0x03401400

#define CONFIG_SYS_DDR_TIMING_3_800             0x00020000
#define CONFIG_SYS_DDR_TIMING_0_800             0x00330004
#define CONFIG_SYS_DDR_TIMING_1_800             0x6f6B4846
#define CONFIG_SYS_DDR_TIMING_2_800             0x0FA8C8CF
#define CONFIG_SYS_DDR_CLK_CTRL_800             0x03000000
#define CONFIG_SYS_DDR_MODE_1_800               0x40461520
#define CONFIG_SYS_DDR_MODE_2_800               0x8000c000
#define CONFIG_SYS_DDR_INTERVAL_800             0x0C300000
#define CONFIG_SYS_DDR_WRLVL_CONTROL_800        0x8655A608

#define CONFIG_SYS_DDR_TIMING_3_1333            0x01061000
#define CONFIG_SYS_DDR_TIMING_0_1333            0x00440104
#define CONFIG_SYS_DDR_TIMING_1_1333            0x98913A45
#define CONFIG_SYS_DDR_TIMING_2_1333            0x0FB8B114
#define CONFIG_SYS_DDR_CLK_CTRL_1333            0x02800000
#define CONFIG_SYS_DDR_MODE_1_1333              0x00061A50
#define CONFIG_SYS_DDR_MODE_2_1333              0x00100000
#define CONFIG_SYS_DDR_INTERVAL_1333            0x144E0513
#define CONFIG_SYS_DDR_WRLVL_CONTROL_1333       0x8655F607

/*FIXME: the following params are constant w.r.t diff freq
combinations. this should be removed later
*/
#if CONFIG_DDR_CLK_FREQ == 100000000
#define CONFIG_SYS_DDR_CS0_CONFIG CONFIG_SYS_DDR_CS0_CONFIG_800
#define CONFIG_SYS_DDR_CONTROL          CONFIG_SYS_DDR_CONTROL_800
#define CONFIG_SYS_DDR_CONTROL_2 CONFIG_SYS_DDR_CONTROL_2_800
#define CONFIG_SYS_DDR_TIMING_4 CONFIG_SYS_DDR_TIMING_4_800
#define CONFIG_SYS_DDR_TIMING_5 CONFIG_SYS_DDR_TIMING_5_800
#elif CONFIG_DDR_CLK_FREQ == 133000000
#define CONFIG_SYS_DDR_CS0_CONFIG CONFIG_SYS_DDR_CS0_CONFIG_1333
#define CONFIG_SYS_DDR_CONTROL          CONFIG_SYS_DDR_CONTROL_1333
#define CONFIG_SYS_DDR_CONTROL_2        CONFIG_SYS_DDR_CONTROL_2_1333
#define CONFIG_SYS_DDR_TIMING_4 CONFIG_SYS_DDR_TIMING_4_1333
#define CONFIG_SYS_DDR_TIMING_5 CONFIG_SYS_DDR_TIMING_5_1333
#else
#define CONFIG_SYS_DDR_CS0_CONFIG CONFIG_SYS_DDR_CS0_CONFIG_800
#define CONFIG_SYS_DDR_CONTROL          CONFIG_SYS_DDR_CONTROL_800
#define CONFIG_SYS_DDR_CONTROL_2        CONFIG_SYS_DDR_CONTROL_2_800
#define CONFIG_SYS_DDR_TIMING_4 CONFIG_SYS_DDR_TIMING_4_800
#define CONFIG_SYS_DDR_TIMING_5 CONFIG_SYS_DDR_TIMING_5_800
#endif

/* relocated CCSRBAR */
#define CONFIG_SYS_CCSRBAR      CONFIG_SYS_CCSRBAR_DEFAULT
#define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR_DEFAULT

#define CONFIG_SYS_IMMR         CONFIG_SYS_CCSRBAR

/* DSP CCSRBAR */
#define CONFIG_SYS_FSL_DSP_CCSRBAR      CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
#define CONFIG_SYS_FSL_DSP_CCSRBAR_PHYS CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT

/*
 * IFC Definitions
 */
/* NOR Flash on IFC */

#define CONFIG_SYS_FLASH_BASE           0x88000000
#define CONFIG_SYS_MAX_FLASH_SECT       1024    /* Max number of sector: 32M */

#define CONFIG_SYS_FLASH_BASE_PHYS      CONFIG_SYS_FLASH_BASE

#define CONFIG_SYS_NOR_CSPR     0x88000101
#define CONFIG_SYS_NOR_AMASK    IFC_AMASK(128*1024*1024)
#define CONFIG_SYS_NOR_CSOR     CSOR_NOR_ADM_SHIFT(5)
/* NOR Flash Timing Params */

#define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x01) \
                                | FTIM0_NOR_TEADC(0x03) \
                                | FTIM0_NOR_TAVDS(0x00) \
                                | FTIM0_NOR_TEAHC(0x0f))
#define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x1d) \
                                | FTIM1_NOR_TRAD_NOR(0x09) \
                                | FTIM1_NOR_TSEQRAD_NOR(0x09))
#define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x1) \
                                | FTIM2_NOR_TCH(0x4) \
                                | FTIM2_NOR_TWPH(0x7) \
                                | FTIM2_NOR_TWP(0x1e))
#define CONFIG_SYS_NOR_FTIM3    0x0

#define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS}
#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS      45      /* count down from 45/5: 9..1 */
#define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */

#undef CONFIG_SYS_FLASH_CHECKSUM
#define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */

/* CFI for NOR Flash */
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE

/* NAND Flash on IFC */
#define CONFIG_SYS_NAND_BASE            0xff800000
#define CONFIG_SYS_NAND_BASE_PHYS       CONFIG_SYS_NAND_BASE

#define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
                                | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
                                | CSPR_MSEL_NAND        /* MSEL = NAND */ \
                                | CSPR_V)
#define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64*1024)

#define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
                                | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
                                | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
                                | CSOR_NAND_RAL_2       /* RAL = 2Byes */ \
                                | CSOR_NAND_PGS_2K      /* Page Size = 2K */ \
                                | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
                                | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/

/* NAND Flash Timing Params */
#define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x03) \
                                        | FTIM0_NAND_TWP(0x05) \
                                        | FTIM0_NAND_TWCHT(0x02) \
                                        | FTIM0_NAND_TWH(0x04))
#define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x1c) \
                                        | FTIM1_NAND_TWBE(0x1e) \
                                        | FTIM1_NAND_TRR(0x07) \
                                        | FTIM1_NAND_TRP(0x05))
#define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x08) \
                                        | FTIM2_NAND_TREH(0x04) \
                                        | FTIM2_NAND_TWHRE(0x11))
#define CONFIG_SYS_NAND_FTIM3           FTIM3_NAND_TWW(0x04)

#define CONFIG_SYS_NAND_DDR_LAW         11

/* NAND */
#define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE      1

#define CONFIG_SYS_NAND_BLOCK_SIZE      (128 * 1024)

#ifndef CONFIG_SPL_BUILD
#define CONFIG_FSL_QIXIS
#endif
#ifdef CONFIG_FSL_QIXIS
#define CONFIG_SYS_FPGA_BASE    0xffb00000
#define CONFIG_SYS_I2C_FPGA_ADDR        0x66
#define QIXIS_BASE      CONFIG_SYS_FPGA_BASE
#define QIXIS_LBMAP_SWITCH      9
#define QIXIS_LBMAP_MASK        0x07
#define QIXIS_LBMAP_SHIFT       0
#define QIXIS_LBMAP_DFLTBANK            0x00
#define QIXIS_LBMAP_ALTBANK             0x04
#define QIXIS_RST_CTL_RESET             0x83
#define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
#define QIXIS_RCFG_CTL_RECONFIG_START   0x21
#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08

#define CONFIG_SYS_FPGA_BASE_PHYS       CONFIG_SYS_FPGA_BASE

#define CONFIG_SYS_CSPR2                (CSPR_PHYS_ADDR(CONFIG_SYS_FPGA_BASE) \
                                        | CSPR_PORT_SIZE_8 \
                                        | CSPR_MSEL_GPCM \
                                        | CSPR_V)
#define CONFIG_SYS_AMASK2               IFC_AMASK(64*1024)
#define CONFIG_SYS_CSOR2                0x0
/* CPLD Timing parameters for IFC CS3 */
#define CONFIG_SYS_CS2_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
                                        FTIM0_GPCM_TEADC(0x0e) | \
                                        FTIM0_GPCM_TEAHC(0x0e))
#define CONFIG_SYS_CS2_FTIM1            (FTIM1_GPCM_TACO(0x0e) | \
                                        FTIM1_GPCM_TRAD(0x1f))
#define CONFIG_SYS_CS2_FTIM2            (FTIM2_GPCM_TCS(0x0e) | \
                                        FTIM2_GPCM_TCH(0x8) | \
                                        FTIM2_GPCM_TWP(0x1f))
#define CONFIG_SYS_CS2_FTIM3            0x0
#endif

/* Set up IFC registers for boot location NOR/NAND */
#if defined(CONFIG_NAND) || defined(CONFIG_NAND_SECBOOT)
#define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
#define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
#define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
#define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
#define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR_CSPR
#define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3
#else
#define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR_CSPR
#define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
#define CONFIG_SYS_CSPR1                CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK1               CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CSOR1                CONFIG_SYS_NAND_CSOR
#define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NAND_FTIM0
#define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NAND_FTIM1
#define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NAND_FTIM3
#endif

#define CONFIG_BOARD_EARLY_INIT_R

#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR        0xffd00000      /* stack in RAM */
#define CONFIG_SYS_INIT_RAM_SIZE        0x00004000 /* End of used area in RAM */

#define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE \
                                                - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET

#define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
#define CONFIG_SYS_MALLOC_LEN           (1024 * 1024)   /* Reserved for malloc*/

/* Serial Port */
#define CONFIG_CONS_INDEX       1
#undef  CONFIG_SERIAL_SOFTWARE_FIFO
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE     1
#define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
#ifdef CONFIG_SPL_BUILD
#define CONFIG_NS16550_MIN_FUNCTIONS
#endif

#define CONFIG_SYS_BAUDRATE_TABLE       \
        {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600)
#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR + 0x4700)
#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR + 0x4800)

#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED        400800 /* I2C speed and slave address*/
#define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
#define CONFIG_SYS_FSL_I2C2_SPEED       400800 /* I2C speed and slave address*/
#define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
#define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100

/* I2C EEPROM */
#define CONFIG_ID_EEPROM
#ifdef CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#endif
#define CONFIG_SYS_I2C_EEPROM_ADDR      0x57
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_BUS_NUM       0

/* enable read and write access to EEPROM */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5

/* I2C FPGA */
#define CONFIG_I2C_FPGA
#define CONFIG_SYS_I2C_FPGA_ADDR        0x66

#define CONFIG_RTC_DS3231
#define CONFIG_SYS_I2C_RTC_ADDR         0x68

/*
 * SPI interface will not be available in case of NAND boot SPI CS0 will be
 * used for SLIC
 */
/* eSPI - Enhanced SPI */
#ifdef CONFIG_FSL_ESPI
#define CONFIG_SF_DEFAULT_SPEED         10000000
#define CONFIG_SF_DEFAULT_MODE          SPI_MODE_0
#endif

#if defined(CONFIG_TSEC_ENET)

#define CONFIG_MII                      /* MII PHY management */
#define CONFIG_MII_DEFAULT_TSEC 1       /* Allow unregistered phys */
#define CONFIG_TSEC1    1
#define CONFIG_TSEC1_NAME       "eTSEC1"
#define CONFIG_TSEC2    1
#define CONFIG_TSEC2_NAME       "eTSEC2"

#define TSEC1_PHY_ADDR          0
#define TSEC2_PHY_ADDR          1

#define TSEC1_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC2_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)

#define TSEC1_PHYIDX            0
#define TSEC2_PHYIDX            0

#define CONFIG_ETHPRIME         "eTSEC1"

/* TBI PHY configuration for SGMII mode */
#define CONFIG_TSEC_TBICR_SETTINGS ( \
                TBICR_PHY_RESET \
                | TBICR_ANEG_ENABLE \
                | TBICR_FULL_DUPLEX \
                | TBICR_SPEED1_SET \
                )

#endif  /* CONFIG_TSEC_ENET */

#ifdef CONFIG_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
#endif

#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#define CONFIG_HAS_FSL_DR_USB
#endif

/*
 * Environment
 */
#if defined(CONFIG_RAMBOOT_SDCARD)
#define CONFIG_FSL_FIXED_MMC_LOCATION
#define CONFIG_SYS_MMC_ENV_DEV          0
#define CONFIG_ENV_SIZE                 0x2000
#elif defined(CONFIG_RAMBOOT_SPIFLASH)
#define CONFIG_ENV_SPI_BUS      0
#define CONFIG_ENV_SPI_CS       0
#define CONFIG_ENV_SPI_MAX_HZ   10000000
#define CONFIG_ENV_SPI_MODE     0
#define CONFIG_ENV_OFFSET       0x100000        /* 1MB */
#define CONFIG_ENV_SECT_SIZE    0x10000
#define CONFIG_ENV_SIZE         0x2000
#elif defined(CONFIG_NAND) || defined(CONFIG_NAND_SECBOOT)
#define CONFIG_ENV_SIZE         CONFIG_SYS_NAND_BLOCK_SIZE
#define CONFIG_ENV_OFFSET       ((768 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE)
#define CONFIG_ENV_RANGE        (3 * CONFIG_ENV_SIZE)
#elif defined(CONFIG_SYS_RAMBOOT)
#define CONFIG_ENV_ADDR                 (CONFIG_SYS_MONITOR_BASE - 0x1000)
#define CONFIG_ENV_SIZE                 0x2000
#else
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE         0x2000
#define CONFIG_ENV_SECT_SIZE    0x20000
#endif

#define CONFIG_LOADS_ECHO               /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change */

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP                     /* undef to save memory */
#define CONFIG_CMDLINE_EDITING                  /* Command-line editing */
#define CONFIG_AUTO_COMPLETE                    /* add autocompletion support */
#define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 64 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ    (64 << 20) /* Initial Memory map for Linux */
#define CONFIG_SYS_BOOTM_LEN    (64 << 20) /* Increase max gunzip size */

#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
#endif

/*
 * Dynamic MTD Partition support with mtdparts
 */
#ifdef CONFIG_MTD_NOR_FLASH
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
#define CONFIG_FLASH_CFI_MTD
#define MTDIDS_DEFAULT "nor0=88000000.nor,nand0=ff800000.flash,"
#define MTDPARTS_DEFAULT "mtdparts=88000000.nor:256k(dtb),7m(kernel)," \
                        "55m(fs),1m(uboot);ff800000.flash:1m(uboot)," \
                        "8m(kernel),512k(dtb),-(fs)"
#endif
/*
 * Environment Configuration
 */

#if defined(CONFIG_TSEC_ENET)
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#endif

#define CONFIG_HOSTNAME         BSC9132qds
#define CONFIG_ROOTPATH         "/opt/nfsroot"
#define CONFIG_BOOTFILE         "uImage"
#define CONFIG_UBOOTPATH        "u-boot.bin"

#ifdef CONFIG_SDCARD
#define CONFIG_DEF_HWCONFIG     "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"
#else
#define CONFIG_DEF_HWCONFIG     "hwconfig=sim;usb1:dr_mode=host,phy_type=ulpi\0"
#endif

#define CONFIG_EXTRA_ENV_SETTINGS                               \
        "netdev=eth0\0"                                         \
        "uboot=" CONFIG_UBOOTPATH "\0"                          \
        "loadaddr=1000000\0"                    \
        "bootfile=uImage\0"     \
        "consoledev=ttyS0\0"                            \
        "ramdiskaddr=2000000\0"                 \
        "ramdiskfile=rootfs.ext2.gz.uboot\0"            \
        "fdtaddr=1e00000\0"                             \
        "fdtfile=bsc9132qds.dtb\0"              \
        "bdev=sda1\0"   \
        CONFIG_DEF_HWCONFIG\
        "othbootargs=mem=880M ramdisk_size=600000 " \
                "default_hugepagesz=256m hugepagesz=256m hugepages=1 " \
                "isolcpus=0\0" \
        "usbext2boot=setenv bootargs root=/dev/ram rw " \
                "console=$consoledev,$baudrate $othbootargs; "  \
                "usb start;"                    \
                "ext2load usb 0:4 $loadaddr $bootfile;"         \
                "ext2load usb 0:4 $fdtaddr $fdtfile;"   \
                "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;"   \
                "bootm $loadaddr $ramdiskaddr $fdtaddr\0"       \
        "debug_halt_off=mw ff7e0e30 0xf0000000;"

#define CONFIG_NFSBOOTCOMMAND   \
        "setenv bootargs root=/dev/nfs rw "     \
        "nfsroot=$serverip:$rootpath "  \
        "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
        "console=$consoledev,$baudrate $othbootargs;" \
        "tftp $loadaddr $bootfile;"     \
        "tftp $fdtaddr $fdtfile;"       \
        "bootm $loadaddr - $fdtaddr"

#define CONFIG_HDBOOT   \
        "setenv bootargs root=/dev/$bdev rw rootdelay=30 "      \
        "console=$consoledev,$baudrate $othbootargs;" \
        "usb start;"    \
        "ext2load usb 0:1 $loadaddr /boot/$bootfile;"   \
        "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;"     \
        "bootm $loadaddr - $fdtaddr"

#define CONFIG_RAMBOOTCOMMAND           \
        "setenv bootargs root=/dev/ram rw "     \
        "console=$consoledev,$baudrate $othbootargs; "  \
        "tftp $ramdiskaddr $ramdiskfile;"       \
        "tftp $loadaddr $bootfile;"             \
        "tftp $fdtaddr $fdtfile;"               \
        "bootm $loadaddr $ramdiskaddr $fdtaddr"

#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND

#include <asm/fsl_secure_boot.h>

#endif  /* __CONFIG_H */