1/* 2 * Configuation settings for the esd TASREG board. 3 * 4 * (C) Copyright 2004 5 * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10/* 11 * board/config.h - configuration options, board specific 12 */ 13 14#ifndef _M5249EVB_H 15#define _M5249EVB_H 16 17/* 18 * High Level Configuration Options 19 * (easy to change) 20 */ 21#define CONFIG_MCFTMR 22 23#define CONFIG_MCFUART 24#define CONFIG_SYS_UART_PORT (0) 25 26#undef CONFIG_WATCHDOG 27 28#undef CONFIG_MONITOR_IS_IN_RAM /* no pre-loader required!!! ;-) */ 29 30/* 31 * BOOTP options 32 */ 33#undef CONFIG_BOOTP_BOOTFILESIZE 34#undef CONFIG_BOOTP_BOOTPATH 35#undef CONFIG_BOOTP_GATEWAY 36#undef CONFIG_BOOTP_HOSTNAME 37 38/* 39 * Command line configuration. 40 */ 41 42#define CONFIG_SYS_LONGHELP /* undef to save memory */ 43 44#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */ 45#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ 46#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ 47 48#define CONFIG_SYS_LOAD_ADDR 0x200000 /* default load address */ 49 50#define CONFIG_SYS_MEMTEST_START 0x400 51#define CONFIG_SYS_MEMTEST_END 0x380000 52 53/* 54 * Clock configuration: enable only one of the following options 55 */ 56 57#undef CONFIG_SYS_PLL_BYPASS /* bypass PLL for test purpose */ 58#define CONFIG_SYS_FAST_CLK 1 /* MCF5249 can run at 140MHz */ 59#define CONFIG_SYS_CLK 132025600 /* MCF5249 can run at 140MHz */ 60 61/* 62 * Low Level Configuration Settings 63 * (address mappings, register initial values, etc.) 64 * You should know what you are doing if you make changes here. 65 */ 66 67#define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */ 68#define CONFIG_SYS_MBAR2 0x80000000 69 70/*----------------------------------------------------------------------- 71 * Definitions for initial stack pointer and data area (in DPRAM) 72 */ 73#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 74#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */ 75#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 76#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 77 78#define LDS_BOARD_TEXT \ 79 . = DEFINED(env_offset) ? env_offset : .; \ 80 env/embedded.o(.text); 81 82#define CONFIG_ENV_OFFSET 0x4000 /* Address of Environment Sector*/ 83#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ 84#define CONFIG_ENV_SECT_SIZE 0x2000 /* see README - env sector total size */ 85 86/*----------------------------------------------------------------------- 87 * Start addresses for the final memory configuration 88 * (Set up by the startup code) 89 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 90 */ 91#define CONFIG_SYS_SDRAM_BASE 0x00000000 92#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */ 93#define CONFIG_SYS_FLASH_BASE (CONFIG_SYS_CS0_BASE) 94 95#if 0 /* test-only */ 96#define CONFIG_PRAM 512 /* test-only for SDRAM problem!!!!!!!!!!!!!!!!!!!! */ 97#endif 98 99#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) 100 101#define CONFIG_SYS_MONITOR_LEN 0x20000 102#define CONFIG_SYS_MALLOC_LEN (1 * 1024*1024) /* Reserve 1 MB for malloc() */ 103#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 104 105/* 106 * For booting Linux, the board info and command line data 107 * have to be in the first 8 MB of memory, since this is 108 * the maximum mapped by the Linux kernel during initialization ?? 109 */ 110#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) 111 112/*----------------------------------------------------------------------- 113 * FLASH organization 114 */ 115#define CONFIG_SYS_FLASH_CFI 116#ifdef CONFIG_SYS_FLASH_CFI 117 118# define CONFIG_FLASH_CFI_DRIVER 1 119# define CONFIG_SYS_FLASH_SIZE 0x1000000 /* Max size that the board might have */ 120# define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 121# define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ 122# define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */ 123# define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ 124# define CONFIG_SYS_FLASH_CHECKSUM 125# define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } 126#endif 127 128/*----------------------------------------------------------------------- 129 * Cache Configuration 130 */ 131#define CONFIG_SYS_CACHELINE_SIZE 16 132 133#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 134 CONFIG_SYS_INIT_RAM_SIZE - 8) 135#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 136 CONFIG_SYS_INIT_RAM_SIZE - 4) 137#define CONFIG_SYS_ICACHE_INV (CF_CACR_DCM) 138#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_FLASH_BASE | \ 139 CF_ADDRMASK(2) | \ 140 CF_ACR_EN | CF_ACR_SM_ALL) 141#define CONFIG_SYS_CACHE_ACR1 (CONFIG_SYS_SDRAM_BASE | \ 142 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ 143 CF_ACR_EN | CF_ACR_SM_ALL) 144#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CEIB | \ 145 CF_CACR_DBWE) 146 147/*----------------------------------------------------------------------- 148 * Memory bank definitions 149 */ 150 151/* CS0 - AMD Flash, address 0xffc00000 */ 152#define CONFIG_SYS_CS0_BASE 0xffe00000 153#define CONFIG_SYS_CS0_CTRL 0x00001980 /* WS=0110, AA=1, PS=10 */ 154/** Note: There is a CSMR0/DRAM vector problem, need to disable C/I ***/ 155#define CONFIG_SYS_CS0_MASK 0x003f0021 /* 4MB, AA=0, WP=0, C/I=1, V=1 */ 156 157/* CS1 - FPGA, address 0xe0000000 */ 158#define CONFIG_SYS_CS1_BASE 0xe0000000 159#define CONFIG_SYS_CS1_CTRL 0x00000d80 /* WS=0011, AA=1, PS=10 */ 160#define CONFIG_SYS_CS1_MASK 0x00010001 /* 128kB, AA=0, WP=0, C/I=0, V=1*/ 161 162/*----------------------------------------------------------------------- 163 * Port configuration 164 */ 165#define CONFIG_SYS_GPIO_FUNC 0x00000008 /* Set gpio pins: none */ 166#define CONFIG_SYS_GPIO1_FUNC 0x00df00f0 /* 36-39(SWITCH),48-52(FPGAs),54*/ 167#define CONFIG_SYS_GPIO_EN 0x00000008 /* Set gpio output enable */ 168#define CONFIG_SYS_GPIO1_EN 0x00c70000 /* Set gpio output enable */ 169#define CONFIG_SYS_GPIO_OUT 0x00000008 /* Set outputs to default state */ 170#define CONFIG_SYS_GPIO1_OUT 0x00c70000 /* Set outputs to default state */ 171#define CONFIG_SYS_GPIO1_LED 0x00400000 /* user led */ 172 173#endif /* M5249 */ 174