LXR uboot/include/configs/ls1012a

   1/*
   2 * Copyright 2016 Freescale Semiconductor
   3 *
   4 * SPDX-License-Identifier:     GPL-2.0+
   5 */
   6
   7#ifndef __LS1012A_COMMON_H
   8#define __LS1012A_COMMON_H
   9
  10#define CONFIG_FSL_LAYERSCAPE
  11#define CONFIG_GICV2
  12
  13#include <asm/arch/config.h>
  14#include <asm/arch/stream_id_lsch2.h>
  15
  16#define CONFIG_DISPLAY_BOARDINFO_LATE
  17
  18#define CONFIG_SYS_CLK_FREQ             125000000
  19
  20#define CONFIG_SKIP_LOWLEVEL_INIT
  21
  22#define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
  23#define CONFIG_SYS_LOAD_ADDR    (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
  24
  25#define CONFIG_SYS_DDR_SDRAM_BASE       0x80000000
  26#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY       0
  27#define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  28#define CONFIG_SYS_DDR_BLOCK2_BASE     0x880000000ULL
  29
  30/* Generic Timer Definitions */
  31#define COUNTER_FREQUENCY               25000000        /* 25MHz */
  32
  33/* CSU */
  34#define CONFIG_LAYERSCAPE_NS_ACCESS
  35
  36/* Size of malloc() pool */
  37#define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + 128 * 1024)
  38
  39/*SPI device */
  40#ifdef CONFIG_QSPI_BOOT
  41#define CONFIG_SYS_QE_FW_IN_SPIFLASH
  42#define CONFIG_SYS_FMAN_FW_ADDR         0x400d0000
  43#define CONFIG_ENV_SPI_BUS              0
  44#define CONFIG_ENV_SPI_CS               0
  45#define CONFIG_ENV_SPI_MAX_HZ           1000000
  46#define CONFIG_ENV_SPI_MODE             0x03
  47#define CONFIG_SPI_FLASH_SPANSION
  48#define CONFIG_FSL_SPI_INTERFACE
  49#define CONFIG_SF_DATAFLASH
  50
  51#define CONFIG_FSL_QSPI
  52#define QSPI0_AMBA_BASE         0x40000000
  53#define CONFIG_SPI_FLASH_SPANSION
  54
  55#define FSL_QSPI_FLASH_SIZE             SZ_64M
  56#define FSL_QSPI_FLASH_NUM              2
  57
  58/*
  59 * Environment
  60 */
  61#define CONFIG_ENV_OVERWRITE
  62
  63#define CONFIG_ENV_SIZE                 0x40000          /* 256KB */
  64#define CONFIG_ENV_OFFSET               0x300000        /* 3MB */
  65#define CONFIG_ENV_SECT_SIZE            0x40000
  66#endif
  67
  68/* SATA */
  69#define CONFIG_SCSI_AHCI_PLAT
  70
  71#define CONFIG_SYS_SATA                         AHCI_BASE_ADDR
  72
  73#define CONFIG_SYS_SCSI_MAX_SCSI_ID             1
  74#define CONFIG_SYS_SCSI_MAX_LUN                 1
  75#define CONFIG_SYS_SCSI_MAX_DEVICE              (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
  76                                                CONFIG_SYS_SCSI_MAX_LUN)
  77
  78/* I2C */
  79#define CONFIG_SYS_I2C
  80#define CONFIG_SYS_I2C_MXC
  81#define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  82#define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  83
  84#define CONFIG_CONS_INDEX       1
  85#define CONFIG_SYS_NS16550_SERIAL
  86#define CONFIG_SYS_NS16550_REG_SIZE     1
  87#define CONFIG_SYS_NS16550_CLK          (get_serial_clock())
  88
  89#define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200 }
  90
  91#define CONFIG_SYS_HZ                   1000
  92
  93#define CONFIG_HWCONFIG
  94#define HWCONFIG_BUFFER_SIZE            128
  95
  96#ifndef CONFIG_SPL_BUILD
  97#define BOOT_TARGET_DEVICES(func) \
  98        func(SCSI, scsi, 0) \
  99        func(MMC, mmc, 0) \
 100        func(USB, usb, 0)
 101#include <config_distro_bootcmd.h>
 102#endif
 103
 104/* Initial environment variables */
 105#define CONFIG_EXTRA_ENV_SETTINGS               \
 106        "verify=no\0"                           \
 107        "loadaddr=0x80100000\0"                 \
 108        "kernel_addr=0x100000\0"                \
 109        "fdt_high=0xffffffffffffffff\0"         \
 110        "initrd_high=0xffffffffffffffff\0"      \
 111        "kernel_start=0x1000000\0"              \
 112        "kernel_load=0xa0000000\0"              \
 113        "kernel_size=0x2800000\0"               \
 114
 115#undef CONFIG_BOOTCOMMAND
 116#define CONFIG_BOOTCOMMAND              "sf probe 0:0; sf read $kernel_load "\
 117                                        "$kernel_start $kernel_size && "\
 118                                        "bootm $kernel_load"
 119
 120/* Monitor Command Prompt */
 121#define CONFIG_SYS_CBSIZE               512     /* Console I/O Buffer Size */
 122#define CONFIG_SYS_MAXARGS              64      /* max command args */
 123
 124#define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 125
 126#include <asm/arch/soc.h>
 127
 128#endif /* __LS1012A_COMMON_H */
 129